CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service center.
A0127W & A0127IA
Keypad
(for use with the A4601)
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Pwr Mute
500-071 rev E
C
HANNEL
V
ISION
TM
© 2004 Channel Vision Technology
A0127 Keypad
A0127 ... Keypad controller for use with the A4601.
Features:
Available in both white (A0127W) and ivory/almond (A0127IA) colors.
Teaching capability allows controls to be stored in learning remote controls.
User changeable source buttons make it easy to customize.
Source selection buttons allow any of the 4 sources to be selected for playback.
Volume +/- buttons.
Increases or decreases the audio level in a zone.
Power button.
Turns off the audio and video playing in a zone.
2
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Pwr Mute
Mute button.
Mutes the audio playing in a zone (video will still be present).
IR receiver.
Detects IR signals and repeats through the IR system.
How IR repeating works
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
The Pwr button flashes as IR information is received.
Point any
IR remote control at the A0127
Pwr Mute
Channe
AB-500
Vis io n
TM
VCR
DVD
Tu
TV
CD
Select
Sat
Off
All
O
Learn
Error
Ch
Power
7
0
8
4
-/--
9
5
1
2
Learn
Rew<<
Play>
Tx
Batt
Stop
Pause
FF>>
3
6
Vo
CD player
Be sure the flasher is attached directly over the component’s IR receiver.
And the flasher repeats the IR signal in the other room.
Using the A0501 remote control.. designed to control your A4601.
(Download IR codes at: www.channelvision.com
and www.remotecentral.com
)
Zone Power - Turns on/off the zone you are in
Power - Master power
(turns all zones on/off)
C HANNEL V
ISION TM
POWER
MODEL
A0501 1
R
C
E
S
O
U
2
3
4
ZONE
POWER
Source Buttons
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Pwr Mute
MUTE
VOL
Mute - Mutes the audio for the zone you are in
VOL - Controls volume for the zone you are in
C HANNEL
V ISI
W
PO
TM
ON
ER
MO
DE
L
1
S
O
U
2
R
C
E
3
4
ZO
NE
POWE
R
VO
L
MU
TE
Setting the A0127 as the master keypad...
By changing a jumper setting on the A0127 you can make it a master keypad.
This simply means that the master A0127 will be able to power on or power off the entire system from a single zone.
Normal control jumper position
Power button will now turn off/on all zones
Master control jumper position
When the system is powered back on each zone will return to its previous volume level and source selection.
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Pwr Mute
7
6
Wiring the A0127 keypad...
Keypads connect to the A4601 through the RJ45 jacks on the back panel of the A4601. Connections to the A0127 may be accomplished either by using the RJ45 jack or the screw terminals provided on the back side of the keypad.
When using the RJ45 jacks, simply wire both ends of the cable according to the TIA568A standard. When using the screw terminals on the A0127, make sure to wire the RJ45 plug connecting to the A4601 as shown below.
Pin
IR
4: signal
7:
Ground
8:
+VDC
Pin Pin
Pin
IR
4: signal
Pin
7:
Ground
8:
+VDC
Pin
Front
A0127
Rear
A4601
Changing buttons face plates on the A0127 keypad...
The A0127IA comes with both Almond and Ivory face plates and buttons.
Both the A0127W and A0127IA come with replacement buttons labeled for a variety of sources.
Faceplate tabs
The procedure below describes the how to exchange your buttons and faceplate.
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Cam 1
Pwr Mute
Tuner
Sat
CD
DVD
Zone
CD 2
XM
Sirius
Cam 2
Cam 3
Cam 4
TV
1 Detach the existing faceplate by pressing the plastic tabs with a flat blade screwdriver. (Press inward and upward
1 at a 30 degree angle)
30°
1
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Pwr Mute
Buttons
Align rubber tabs with holes in PCB
2 Exchange the labeled buttons
(and colored faceplate) to your preference and assemble as shown
Pin 8: +VDC
Pin 4: IR signal
N.C.
Pin 7: Ground
Accessories
AB-500 ... Universal remote control.. Learns IR codes for up to 6 sources.
IR-3003 & IR-3002 ... Single and dual head IR flashers. Use one head per source to control from the remote room. (IR-3002 shown).
3
4
See page 6 for connection details
Channel Vision A4601
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
6 Control 5
R-Audio-L
OUTPUTS
Video
5
6
AB-500
4 Control 3
R-Audio-L
OUTPUTS
Video
3
4
GLOBAL
INPUT
R IN
L IN
1
R OUT
R IN
LOCAL
L IN
GLOBAL L OUT
2
R OUT
R IN
LOCAL
L IN
GLOBAL L OUT
R IN
CHANNELS
3
R OUT
R IN
4
R OUT
LOCAL LOCAL
L IN
GLOBAL L OUT
L IN
GLOBAL L OUT
A1260 Rear Panel
5
R OUT
R IN
LOCAL
L IN
GLOBAL L OUT
6
R IN
LOCAL
L IN
GLOBAL
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
Pwr Mute
Room 6
Sat radio
DVD player
CD player
2 Control 1
O UTPUTS
Video
1
Hi-Z
75
1 2 3 4
2
Sig
Gnd
+V
R-Audio-L
IR Emitters
Video
3
4
INPUTS
R-Audio-L
1A/250V
FUSE
Input Voltage
115
Video
1
2
230 / 115 VAC
50 / 60 Hz
Power
IR emitter outputs allow IR-3002 flashers to be connected for remote control of source components.
Each zone is controlled through the A0127 keypad which connects to the RJ45 jacks on the rear panel.
A learning remote (such as the AB-500) can be programmed to control your source components and the A0127 (see page 7 for details). This is an easy way to control all your components from any room in the house.
Note: If you are using a Philips Pronto remote control, you may download IR codes for the A0127 from www.channelvision.com
or from www.remotecentral.com.
5
