User`s guide | Electrolux 242000100 Refrigerator User Manual

Intel® Server Chassis SC5400 User’s
Guide
A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/
Products
Intel Order Number D38435-005
Disclaimer
Information in this document is provided in connection with Intel® products. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's
Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any
express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to
fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property
right. Intel products are not designed, intended or authorized for use in any medical, life saving, or life sustaining
applications or for any other application in which the failure of the Intel product could create a situation where
personal injury or death may occur. Intel may make changes to specifications and product descriptions at any time,
without notice.
Intel server boards contain a number of high-density VLSI and power delivery components that need adequate
airflow for cooling. Intel's own chassis are designed and tested to meet the intended thermal requirements of these
components when the fully integrated system is used together. It is the responsibility of the system integrator that
chooses not to use Intel developed server building blocks to consult vendor datasheets and operating parameters to
determine the amount of airflow required for their specific application and environmental conditions. Intel
Corporation can not be held responsible if components fail or the server board does not operate correctly when used
outside any of their published operating or non-operating limits.
Intel, Intel Pentium, and Intel Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in
the United States and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2006 - 2007, Intel Corporation. All Rights Reserved
ii
Intel® Server Chassis SC5400 User’s Guide
Safety Information
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the
instructions. See also Intel Server Boards and Server Chassis Safety Information on the
Intel® Server Deployment Toolkit CD and/or at http://support.intel.com/support/
motherboards/server/sb/cs-010770.htm.
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warnund Sicherheitshinweise in diesem Dokument, bevor
Sie eine der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu
Intel-Serverplatinen und Servergehäusen auf der Intel® Server Deployment Toolkit CD
oder unter http://support.intel.com/support/motherboards/server/sb/cs-010770.htm.
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce
document avant de suivre toute instruction. Consultez Intel Server Boards and Server
Chassis Safety Information sur le Intel® Server Deployment Toolkit CD ou bien rendezvous sur le site http://support.intel.com/support/motherboards/server/sb/cs-010770.htm.
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar
cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety
Information en el Intel® Server Deployment Toolkit CD y/o en http://support.intel.com/
support/motherboards/server/sb/cs-010770.htm.
iii
Intel® Server Chassis SC5400 User’s Guide
重要安全指导
Warnings
Heed safety instructions: Before working with your server product, whether you are
using this guide or any other resource as a reference, pay close attention to the safety
instructions. You must adhere to the assembly instructions in this guide to ensure and
maintain compliance with existing product certifications and approvals. Use only the
described, regulated components specified in this guide. Use of other products /
components will void the UL listing and other regulatory approvals of the product and
will most likely result in non-compliance with product regulations in the region(s) in
which the product is sold.
System power on/off: The power button DOES NOT turn off the system AC power. To
remove power from system, you must unplug the AC power cord from the wall outlet.
Make sure the AC power cord is unplugged before you open the chassis, add, or remove
any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be
present on power, telephone, and communication cables. Turn off the server and
disconnect the power cord, telecommunications systems, networks, and modems attached
to the server before opening it. Otherwise, personal injury or equipment damage can
result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives,
boards, and other parts. We recommend that you perform all procedures in this chapter
only at an ESD workstation. If one is not available, provide some ESD protection by
wearing an anti-static wrist strap attached to chassis ground any unpainted metal surface
on your server when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely
sensitive to ESD. Hold boards only by their edges. After removing a board from its
protective wrapper or from the server, place the board component side up on a grounded,
static free surface. Use a conductive foam pad if available but not the board wrapper. Do
not slide board over any surface.
iv
Intel® Server Chassis SC5400 User’s Guide
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips
over two jumper pins. Some jumpers have a small tab on top that you can grip with your
fingertips or with a pair of fine needle nosed pliers. If your jumpers do not have such a
tab, take care when using needle nosed pliers to remove or install a jumper; grip the
narrow sides of the jumper with the pliers, never the wide sides. Gripping the wide sides
can damage the contacts inside the jumper, causing intermittent problems with the
function controlled by that jumper. Take care to grip with, but not squeeze, the pliers or
other tool you use to remove a jumper, or you may bend or break the pins on the board.
Intel® Server Chassis SC5400 User’s Guide
v
vi
Intel® Server Chassis SC5400 User’s Guide
Preface
About this Manual
Thank you for purchasing and using the Intel® Server Chassis SC5400.
This manual is written for system technicians who are responsible for troubleshooting,
upgrading, and repairing this server chassis. This document provides a brief overview of
the features of the chassis, a list of accessories or other components you may need,
troubleshooting information, and instructions on how to add and replace components on
the Intel® Server Chassis SC5400. For the latest version of this manual, see http://
support.intel.com/support/motherboards/server/chassis/SC5400/.
Manual Organization
Chapter 1 provides a brief overview of the Intel® Server Chassis SC5400. In this chapter,
you will find a list of the server chassis features, photos of the product, and product
diagrams to help you identify components and their locations.
Chapter 2 provides instructions on adding and replacing components. Use this chapter for
step-by-step instructions and diagrams for installing or replacing components such as the
fans, power supply, drives, and other components.
Chapter 3 provides technical reference information on cable routing, power supply
specifications, and system environment requirements.
At the back of this document, you will find appendices on safety, regulatory, "getting
help", and warranty information.
vii
Product Contents, Order Options, and
Accessories
This server chassis is compatible with the following Intel® Server Boards:
• Intel® Server Board S5000PSL
• Intel® Server Board S5000XVN
Your Intel® Server Chassis SC5400 ships with the following items:
• 670W or 830W power supply, installed in the chassis
• A box of hardware components, referred to below as the "chassis hardware box"
• Fan cables, installed in the Intel® Server Chassis SC5400 with product code
SC5400LX or SC5400LXi
•
•
•
•
•
Chassis intrusion switch, installed in the chassis
Attention document, in the chassis product box
Intel® Server Chassis SC5400 Quick Start User's Guide, in the chassis hardware box
Six 32-6mm flat screws for installing drive component, in the chassis hardware box
Seven screws for mounting the server board into the chassis, in the chassis hardware
box
• USB cable, in the chassis hardware box
• COM2 cable, in the hardware box
In addition, you may need or want to purchase one or more of the following accessory
items for your server: Processor, memory DIMMs, hard drive, floppy drive, CD-ROM or
DVD-ROM drive, RAID controller, operating system.
For information about which accessories, memory, processors, and third-party hardware
have been tested and can be used with your board, and for ordering information for Intel
products, see http://support.intel.com/support/motherboards/server/chassis/SC5400/
compat.htm.
viii
Intel® Server Chassis SC5400 User’s Guide
Additional Information and Software
If you need more information about this product or information about the accessories that
can be used with this server chassis, use the following resources. These files are available
at http://support.intel.com/support/motherboards/server/chassis/SC5400/.
Unless otherwise indicated in the table below, once on this Web page, type the document
or software name in the search field at the left side of the screen and select the option to
search "This Product."
For this information or
software
Use this Document or Software
For in-depth technical
information about this
product, including BIOS
settings and chipset
information
IIntel® Server Chassis SC5400 Technical Product Specification
If you just received this
product and need to install
it
Intel® Server Chassis SC5400 Quick Start User's Guide in the
product box
For virtual system tours
and interactive repair
information
A link to the SMaRT Tool is available under "Other Resources" at the
right side of the screen at:
Accessories or other Intel
server products
Spares and Configuration Guide
Hardware (peripheral
boards, adapter cards) and
operating systems that
have been tested with this
product
Tested Hardware Operating Systems List
For software to manage
your Intel® server
Intel® System Management Software
For diagnostics test
software
Diagnostics
Intel® Server Chassis SC5400 User’s Guide
http://support.intel.com/support/motherboards/server/chassis/
SC5400/
ix
x
Intel® Server Chassis SC5400 User’s Guide
Contents
Safety Information ..................................................................................................... iii
Important Safety Instructions ........................................................................................ iii
Wichtige Sicherheitshinweise ....................................................................................... iii
Consignes de sécurité .................................................................................................. iii
Instrucciones de seguridad importantes ....................................................................... iii
Warnings ...................................................................................................................... iv
Preface ....................................................................................................................... vii
About this Manual ........................................................................................................ vii
Manual Organization ................................................................................................... vii
Product Contents, Order Options, and Accessories ....................................................viii
Additional Information and Software ............................................................................. ix
Chapter 1: Server Chassis Features ......................................................................... 1
Component Identification ............................................................................................... 6
Internal Components .................................................................................................6
Front Control Panel ................................................................................................... 7
Intel® Local Control Panel ......................................................................................... 9
Back Panel Features ...............................................................................................10
Peripheral Devices ..................................................................................................11
Standard and Optional Hot-swap Drive Bays ..............................................................12
Floppy / CD-ROM / DVD-ROM Slimline Carriers ........................................................12
Intel® Remote Management Module ...........................................................................13
Rack-mounted Systems ..............................................................................................13
Chapter 2: Hardware Installations and Upgrades ................................................. 15
Before You Begin ........................................................................................................15
Tools and Supplies Needed ....................................................................................15
System References .................................................................................................15
Removing and Installing the Chassis Cover ................................................................16
Removing the Chassis Cover .................................................................................16
Installing the Chassis Cover ...................................................................................17
Removing and Installing the Front Bezel .....................................................................18
Removing the Bezel Assembly (Pedestal Only) .....................................................18
Installing the Front Bezel (Pedestal Only) ...............................................................19
Removing and Installing the Processor and Memory Air Ducts ..................................20
Removing the Processor and Memory Air Ducts ....................................................20
Installing the Processor and Memory Air Ducts ......................................................21
Replacing a Fixed Fan (Intel® Server Chassis SC5400Base SC5400BRP only) ........23
Removing and Installing Hot Swap Fans (Intel® Server Chassis SC5400LX or
Intel® Server Chassis SC5400 User’s Guide
xi
SC5400LXi Only) ............................................................................................. 24
Removing Hot Swap Fans ...................................................................................... 24
Installing Hot Swap Fans ........................................................................................ 25
Installing and Removing a Slimline USB Floppy/CD/DVD Combo Kit ........................ 26
Installing a Slimline USB Floppy/CD/DVD Slimline Kit ........................................... 26
Removing a Slimline USB Floppy/CD/DVD Combo ............................................... 26
Removing and Installing a DVD or CD-ROM Drive ..................................................... 27
Removing a DVD or CD-ROM Drive ...................................................................... 27
Installing a DVD or CD-ROM Drive ........................................................................ 29
Removing and Installing Fixed Hard Drive(s) .............................................................. 30
Removing Fixed Hard Drive(s) ............................................................................... 30
Installing Fixed Hard Drive(s) ................................................................................. 35
Routing Power Cables to Fixed Drives ....................................................................... 40
Routing Data Cables to Fixed Drives .......................................................................... 41
Removing and Installing Hot Swap Drive(s) ................................................................ 42
Removing Hot Swap Drive(s) ................................................................................. 42
Installing Hot Swap Drive(s) ................................................................................... 44
Removing and Installing PCI Add-in Board(s) ............................................................. 45
Removing PCI Add-in Board(s) .............................................................................. 45
Installing PCI Add-in Board(s) ................................................................................ 47
Installing Additional Hot Swap Power Supply Module ................................................. 51
Replacing a Hot Swap Power Supply ......................................................................... 52
Replacing a Fixed Power Supply ................................................................................ 53
Replacing the Power Distribution Board ..................................................................... 54
Replacing the Control Panel ....................................................................................... 59
Installing and/or Removing a Server Board ................................................................ 60
Connecting and Disconnecting Cables to or from Server Board ................................. 61
Connecting Cables to Server Board ....................................................................... 61
Removing Cables from Server Board(s) ................................................................. 61
Chapter 3: Technical Reference ..............................................................................63
Power Supply Specifications ....................................................................................... 63
670-W Single Power Supply Input Voltages ........................................................... 63
670-W Single Power Supply Output Voltages ........................................................ 63
830-W Single Power Input Voltages ....................................................................... 63
830-W Single Power Supply Output Voltages ........................................................ 64
System Environmental Specifications ......................................................................... 64
Current Usage ............................................................................................................. 65
Calculating Power Usage ....................................................................................... 65
Appendix A: Getting Help ........................................................................................67
World Wide Web ......................................................................................................... 67
Telephone ................................................................................................................... 67
Appendix B: Regulatory and Compliance Information .........................................71
xii
Intel® Server Chassis SC5400 User’s Guide
Product Regulatory Compliance ..................................................................................71
Product Safety Compliance ....................................................................................71
Product Regulatory Compliance References ..........................................................72
Electromagnetic Compatibility Notices ........................................................................75
FCC Verification Statement (USA) ..........................................................................75
Industry Canada (ICES-003) ...................................................................................76
Europe (CE Declaration of Conformity) ..................................................................76
VCCI (Japan) ..........................................................................................................76
BSMI (Taiwan) ........................................................................................................76
Korean Compliance (RRL) ......................................................................................77
CNCA (CCC-China) ................................................................................................77
Product Ecology Compliance ..................................................................................77
Other Markings .......................................................................................................80
Regulated Specified Components ..........................................................................81
End-of-Life / Product Recycling ...................................................................................82
Appendix C: Warranty .............................................................................................. 83
Limited Warranty for Intel® Chassis Subassembly Products .......................................83
Extent of Limited Warranty ..........................................................................................84
Warranty Limitations and Exclusions ...........................................................................84
Limitations of Liability ..............................................................................................84
How to Obtain Warranty Service .................................................................................85
Telephone Support .................................................................................................85
Returning a Defective Product ................................................................................85
Appendix D: Safety Information .............................................................................. 87
English .........................................................................................................................87
Server Safety Information .......................................................................................87
Safety Warnings and Cautions ...............................................................................87
Intended Application Uses ......................................................................................88
Site Selection ..........................................................................................................88
Equipment Handling Practices ................................................................................88
Power and Electrical Warnings ...............................................................................89
System Access Warnings .......................................................................................90
Rack Mount Warnings .............................................................................................90
Electrostatic Discharge (ESD) ................................................................................91
Other Hazards .........................................................................................................91
Sicherheitshinweise für den Server ........................................................................93
Sicherheitshinweise und Vorsichtsmaßnahmen .....................................................93
Zielbenutzer der Anwendung ..................................................................................94
Standortauswahl .....................................................................................................94
Handhabung von Geräten .......................................................................................94
Warnungen zu Netzspannung und Elektrizität ........................................................95
Warnhinweise für den Systemzugang ....................................................................96
Warnhinweise für Racks .........................................................................................97
Intel® Server Chassis SC5400 User’s Guide
xiii
Elektrostatische Entladungen (ESD) ...................................................................... 97
Andere Gefahren .................................................................................................... 98
Français ...................................................................................................................... 99
Consignes de sécurité sur le serveur ..................................................................... 99
Sécurité: avertissements et mises en garde ........................................................... 99
Domaines d’utilisation prévus ............................................................................... 100
Sélection d’un emplacement ................................................................................ 100
Pratiques de manipulation de l’équipement .......................................................... 100
Alimentation et avertissements en matière d’électricité ........................................ 101
Avertissements sur l’accès au système ................................................................ 102
Avertissements sur le montage en rack ............................................................... 102
Décharges électrostatiques (ESD) ....................................................................... 103
Autres risques ....................................................................................................... 103
Información de seguridad del servidor ................................................................. 105
Advertencias y precauciones sobre seguridad ..................................................... 105
Aplicaciones y usos previstos ............................................................................... 106
Selección de la ubicación ..................................................................................... 106
Manipulación del equipo ....................................................................................... 106
Advertencias de alimentación y eléctricas ............................................................ 107
Advertencias el acceso al sistema ....................................................................... 108
Advertencias sobre el montaje en bastidor .......................................................... 108
Descarga electrostática (ESD) ............................................................................. 109
Appendix E: Installation/Assembly Safety Instructions ......................................117
English ...................................................................................................................... 117
Deutsch ..................................................................................................................... 119
Français .................................................................................................................... 122
Español ..................................................................................................................... 124
Italiano ....................................................................................................................... 126
xiv
Intel® Server Chassis SC5400 User’s Guide
List of Figures
Figure 1. Intel® Server Chassis SC5400 ................................................................................... 1
Figure 2. Internal Component Locations ................................................................................... 6
Figure 3. Front Control Panel .................................................................................................... 7
Figure 4. Intel® Local Control Panel Features........................................................................... 9
Figure 5. Server Chassis Back................................................................................................ 10
Figure 6. Optional Peripherals................................................................................................. 11
Figure 7. Removing the Chassis Cover................................................................................... 16
Figure 8. Installing the Chassis Cover..................................................................................... 17
Figure 9. Removing the Front Bezel........................................................................................ 18
Figure 10. Installing the Front Bezel........................................................................................ 19
Figure 11. Removing the Processor and Memory Air Ducts ................................................... 20
Figure 12. Removing Inner Plastic Air Baffle from Processor Air Duct ................................... 21
Figure 13. Installing the Processor and Memory Air Ducts ..................................................... 22
Figure 14. Removing a Fixed Fan ........................................................................................... 23
Figure 15. Removing Hot Swap Fan ....................................................................................... 24
Figure 16. Installing Hot Swap Fan ......................................................................................... 25
Figure 17. Removing Slide/Drive Assembly from Upper Device Bay...................................... 26
Figure 18. Re-inserting Empty EMI Shield/Slide Assembly into Chassis ................................ 27
Figure 19. Re-inserting Empty EMI Shield/Slide Assembly into Chassis ................................ 28
Figure 20. Removing EMI Shield/Slide Assembly from Upper Device Bay............................. 29
Figure 21. Attaching Slides to a DVD or CD-ROM Drive ........................................................ 29
Figure 22. Removing Six-drive Fixed Drive Cage from Chassis ............................................. 31
Figure 23. Unlocking and Opening Upper Door of Fixed Drive Cage ..................................... 31
Figure 24. Opening Lower Door of Fixed Drive Cage ............................................................. 32
Figure 25. Removing Drive/Slide Assembly from Drive Cage................................................. 32
Figure 26. Inserting Empty Device Slides into Drive Cage...................................................... 33
Figure 27. Closing Lower Door of Fixed Drive Cage............................................................... 33
Figure 28. Closing Upper Door of Fixed Drive Cage............................................................... 34
Figure 29. Tightening Thumb Screw ....................................................................................... 34
Figure 30. Removing Six-drive Fixed Drive Cage from Chassis ............................................. 35
Figure 31. Unlocking and Opening Upper Door of Fixed Drive Cage ..................................... 36
Figure 32. Opening Lower Door of Fixed Drive Cage ............................................................. 36
Figure 33. Removing Slides from Drive Cage ......................................................................... 37
Figure 34. Attaching Device Slides to Hard Drive ................................................................... 37
Figure 35. Inserting Drive/Slide Assembly into Drive Cage..................................................... 38
Figure 36. Closing Lower Door of Fixed Drive Cage............................................................... 38
Figure 37. Closing Upper Door of Fixed Drive Cage............................................................... 39
Figure 38. Tightening Captive Screw ...................................................................................... 39
Figure 39. Routing Power Cables to Fixed Drives .................................................................. 40
Figure 40. Routing SAS/SATA Data Cables ........................................................................... 41
Figure 41. Releasing Drive Carrier from Hot Swap Cage ....................................................... 42
Figure 42. Removing Hard Drive from Drive Carrier ............................................................... 42
Intel® Server Chassis SC5400 User’s Guide
xv
Figure 43. Installing Plastic Air Baffle in Drive Carrier ............................................................
Figure 44. Inserting Drive Carrier into Hot Swap Cage...........................................................
Figure 45. Removing Drive Carrier from Hot Swap Cage.......................................................
Figure 46. Removing Plastic Air Baffle ...................................................................................
Figure 47. Securing Hard Drive to Drive Carrier .....................................................................
Figure 48. Inserting Drive Carrier into Hot Swap Cage...........................................................
Figure 49. Preparing Chassis for Removal of PCI Add-in Board ............................................
Figure 50. Preparing Chassis for Addition of PCI Add-in Board .............................................
Figure 51. Installing Add-in Board...........................................................................................
Figure 52. Reinstalling PCI Add-in Card Retainer ..................................................................
Figure 53. Removing Power Supply Filler Panel ....................................................................
Figure 54. Installing Additional Hot Swap Power Supply Module ...........................................
Figure 55. Removing Hot Swap Power Supply from Chassis.................................................
Figure 56. Installing Hot Swap Power Supply into Chassis ....................................................
Figure 57. Removing Fixed Power Supply..............................................................................
Figure 58. Removing Hot Swap Power Supply from Chassis.................................................
Figure 59. Removing Center Divider.......................................................................................
Figure 60. Removing Power Distribution Board......................................................................
Figure 61. Securing Power Distribution Board to Power Supply Cage ...................................
Figure 62. Re-installing Center Divider ...................................................................................
Figure 63. Installing Hot Swap Power Supply into Chassis ....................................................
xvi
43
43
44
44
45
45
46
48
49
50
51
51
52
52
53
54
55
56
57
58
58
Intel® Server Chassis SC5400 User’s Guide
List of Tables
Table 1. Server Chassis Features (BASE SKU) ....................................................................... 2
Table 2. Server Chassis Features (BRP SKU) .......................................................................... 3
Table 3. Server Chassis Features (LX SKU) ............................................................................. 4
Table 4. Server Chassis Features (LXi SKU) ............................................................................5
Table 5. Front Control Panel LED Descriptions ........................................................................ 8
Table 6. 670-W Power Supply Output Capability ....................................................................63
Table 7. 830-W Power Supply Output Capability ....................................................................64
Table 8. Environmental Specifications ....................................................................................64
Table 9. Power Usage Worksheet ...........................................................................................65
Table 10. Power Usage Worksheet 2 ......................................................................................66
Table 11. Product Regulatory Compliance Markings ..............................................................72
Table 12. Product Ecology Compliance Markings ...................................................................78
Table 13. Other Markings ........................................................................................................80
Intel® Server Chassis SC5400 User’s Guide
xvii
xviii
Intel® Server Chassis SC5400 User’s Guide
1
Server Chassis Features
This chapter briefly describes the main features of the Intel® Server Chassis SC5400. This
chapter provides a list of the server chassis features, as well as diagrams showing the
location of important components and connections on the server chassis.
AF000551
Figure 1. Intel® Server Chassis SC5400
Intel® Server Chassis SC5400 User’s Guide
1
Table 1 summarizes the features of the Intel® Server Chassis SC5400 Base SKU
Table 1. Server Chassis Features (BASE SKU)
Feature
Dimensions
Hard Drives
Description
•
•
•
•
16.6 inches high (Pedestal: 17 inches)
8.6 inches wide
27.4 inches deep (Pedestal: 28.4 inches)
34.6 kilograms
One fixed drive bay for up to six fixed SAS or SATA drives.
Optional hot-swap drive bays:
•
•
Six-drive SAS/SATA
Four-drive SAS/SATA
An optional four-drive fixed drive bay is also available.
Peripherals
Control Panel (dependent
on option selected)
•
•
•
•
Supports up to six drives, depending on peripheral choices.
Three multi-mount 5.25 peripheral bays
Front Control Panel
Intel® Local Control Panel (optional)
LEDs and displays
(dependent on option
selected)
With Front Control Panel:
Power Supply
One fixed 670-W power supply with an integrated cooling fan.
Upgradable to 830-W redundant power supplies.
Fans
Two fixed, non-redundant chassis fans:
•
•
•
•
•
•
NIC1 Activity
NIC2 Activity
Power / Sleep
System Status
System Identification
Hard Drive Activity
•
•
One 120-mm fan
One 92-mm fan
Upgradable to redundant.
USB 2.0
Video
2
•
•
•
Two front panel USB ports with Front Control Panel
Four back panel USB ports (depending on server board)
One rear panel video port
NOTE: The 12V 6-pin power connector is for the 150-W PCIe video
cards, which require an external 75-W power connector.
Intel® Server Chassis SC5400 User’s Guide
Table 2 summarizes the features of the BRP SKU.
Table 2. Server Chassis Features (BRP SKU)
Feature
Dimensions
Hard Drives
Description
•
•
•
•
16.6 inches high (Pedestal: 17 inches)
8.6 inches wide
27.4 inches deep (Pedestal: 28.4 inches)
36.2 kilograms
One fixed drive bay for up to six fixed SAS or SATA drives.
Optional hot swap drive bays:
•
•
Six-drive SAS/SATA
Four-drive SAS/SATA
An optional four-drive fixed drive bay is also available.
Peripherals
Control Panel (dependent
on option selected)
•
•
•
•
Supports up to ten drives
Three multi-mount 5.25-inch peripheral bays
Front Control Panel
Intel® Local Control Panel (optional)
LEDs and displays
(dependent on option
selected)
With Front Control Panel:
Power Supply
One 830-W power supply is standard. Upgradable to 830-W
redundant power supplies
Fans
Two fixed, non-redundant chassis fans:
•
•
•
•
•
•
NIC1 Activity
NIC2 Activity
Power / Sleep
System Status
System Identification
Hard Drive Activity
•
•
One 120-mm fan
One 92-mm fan
Upgradable to redundant.
USB 2.0
Video
•
•
•
•
Intel® Server Chassis SC5400 User’s Guide
Two front panel USB ports with Front Control Panel
Four back panel USB ports
One front panel video port (available only with Front Control
Panel)
One rear panel video port
3
Table 3 summarizes the features of the LX SKU.
Table 3. Server Chassis Features (LX SKU)
Feature
Dimensions
Hard Drives
Description
•
•
•
•
16.6 inches high (Pedestal: 17 inches)
8.6 inches wide
27.4 inches deep (Pedestal: 28.4 inches)
36.2 kilograms
One fixed drive bay for up to six fixed SAS or SATA drives.
Optional hot-swap drive bays:
•
•
Six-drive SAS/SATA
Four-drive SAS/SATA
An optional four-drive fixed drive bay is also available.
Peripherals
Control Panel (dependent
on option selected)
•
•
•
•
Three multi-mount 5.25-inch peripheral bays
Front Control Panel
Intel® Local Control Panel (optional)
LEDs and displays
(dependent on option
selected)
With Front Control Panel:
Power Supply
One redundant capable 830-W power supply module with an
integrated cooling fan. Optional second redundant power supply
module is available.
Fans
Four hot-swap, redundant chassis fans:
USB 2.0
Video
•
•
•
•
•
•
•
•
•
•
•
•
4
Supports up to ten drives
NIC1 Activity
NIC2 Activity
Power / Sleep
System Status
System Identification
Hard Drive Activity
Two 120-mm fans
Two 92-mm fans
Two front panel USB ports with Front Control Panel
Four back panel USB ports
One front panel video port (available only with Standard Control
Panel)
One rear panel video port
Intel® Server Chassis SC5400 User’s Guide
Table 3 summarizes the features of the SC5400LXi SKU
Table 4. Server Chassis Features (LXi SKU)
Feature
Dimensions
Hard Drives
Description
•
•
•
•
16.6 inches high (Pedestal: 17 inches)
8.6 inches wide
27.4 inches deep (Pedestal: 28.4 inches)
36.2 kilograms
One fixed drive bay for up to six fixed SAS or SATA drives.
Optional expanded or non-expanded hot-swap drive bays:
•
•
Six-drive SAS/SATA
Four-drive SAS/SATA
An optional four-drive fixed drive bay is available.
Peripherals
Control Panel (dependent
on option selected)
•
•
•
•
Supports up to ten drives
Three multi-mount 5.25-inch peripheral bays
Front Control Panel
Intel® Local Control Panel (optional)
LEDs and displays
(dependent on option
selected)
With Front Control Panel:
Power Supply
One redundant capable 830-W power supply module with an
integrated cooling fan. Optional second redundant power supply
module is available.
Fans
Four hot-swap, redundant chassis fans:
USB 2.0
Video
•
•
•
•
•
•
•
•
•
•
•
•
Intel® Server Chassis SC5400 User’s Guide
NIC1 Activity
NIC2 Activity
Power / Sleep
System Status
System Identification
Hard Drive Activity
Two 120-mm fans
Two 92-mm fans
Two front panel USB ports with Front Control Panel
Four back panel USB ports
One front panel video port (available only with Standard Control
Panel)
One rear panel video port
5
Component Identification
Internal Components
A
I
H
D
E
J
B
C
K
F
G
L
AF000511
A.
Fixed Power Supply
G.
Hard Disk Drive Cage Release
Mechanisms (2)
B.
Rear Serial B Connector
H.
Front Panel Controls
C.
PCI Add-in Card Panel
I.
5.25-inch Device Bays
D.
Memory Air Duct
J.
Front Panel USB/Serial B
E.
Processor Air Duct
K.
Fixed Drive Cage 4-Drive (accessory)
F.
Fixed Fans (2)
L.
Fixed Drive Cage 6-Drive
Figure 2. Internal Component Locations
6
Intel® Server Chassis SC5400 User’s Guide
Front Control Panel
The following figure shows the features available on the Front Control Panel. The Intel®
Local Control Panel is optional.
A
B
F
C
G
D
H
E
I
TP00701
A.
ID Toggle Switch
F.
NIC2 Activity LED (green)
B.
Reset Button
G.
ID LED (blue)
C.
NIC 1 Activity LED (green)
H.
Status LED (bi-color)
D.
Power Button
I.
NMI Button
E.
Hard Drive Activity LED (green)
Figure 3. Front Control Panel
Intel® Server Chassis SC5400 User’s Guide
7
Descriptions of the front control panel LEDs are listed in the following table. See your
server documentation for functionality of buttons.
Table 5. Front Control Panel LED Descriptions
LED Name
Power LED
Status
Green
Condition
Description
On
Power on
Off
Power off
On
System ready
Blink
System ready, but degraded: some CPU fault,
DIMM killed
Green/Blink
Amber
Blink
Condition during BMC reset.
Amber
On
Critical alarm: critical power module failure, critical
fan failure, voltage (power supply), voltage and
thermal fault
Blink
Non-critical failure: redundant fan failure,
redundant power failure, non-critical power and
voltage
Off
System not ready: POST error/NMI event/PCI or
terminator missing
Green
Hard drive
activity
Green
Blink
Hard drive activity
NIC1 activity
Green
On
Linked
Blink
LAN activity
Off
Idle
On
Linked
Blink
LAN activity
Off
Idle
Blink
Server identification; toggled by ID button or
software
Off
Server identification; toggled by ID button or
software
NIC2 activity
ID LED (rack
only)
8
Color
Green
Blue
Intel® Server Chassis SC5400 User’s Guide
Intel® Local Control Panel
The following figure shows the features available on the Intel® Local Control Panel. The
Intel® Local Control Panel is optional.
Note: The Intel® Local Control Panel requires the installation of the Intel® Remote
Management Module. See your server board documentation to determine if this control
panel is compatible with your server board.
A
B
C
D
E
AF000955
Callout
Function
A.
LCD display (variable content)
B.
LCD up navigation button
C.
LCD down navigation button
D.
LCD backup level navigation button
E.
LCD command enter button
Figure 4. Intel® Local Control Panel Features
Intel® Server Chassis SC5400 User’s Guide
9
Back Panel Features
A
G
B
F
E
D
C
TP00526
A.
Fixed Power Supply
B.
I/O Ports
C.
PCI Add-in Card Slots
D.
PCI Card Latch
E.
Rear Serial B Connector (optional)
F.
Knockout
G.
AC Power Connector
Note: I/O connectors vary, depending on the server board installed. See your server board
documentation for port identification.
Figure 5. Server Chassis Back
10
Intel® Server Chassis SC5400 User’s Guide
Peripheral Devices
The chassis provides locations and hardware for installing hard drives, a floppy drive, a
CD-ROM drive, or a DVD-ROM drive. The drives must be purchased separately. The
following figure shows the available options.
A
B
C
AF000552
A.
B.
C.
Slimline floppy drive / DVD-ROM drive / CD-ROM drive
USB ports (2)
Hard drive bays
Figure 6. Optional Peripherals
Intel® Server Chassis SC5400 User’s Guide
11
Standard and Optional Hot-swap Drive Bays
One bay supporting six cabled drives ships with the standard chassis. Optional hot swap
drive bays may replace the six-drive fixed drive bay. An optional four-drive fixed drive
bay (for cabled drives) is available. No tools are required to replace the fixed drive bays.
Optional four-drive and six-drive SAS/SATA and SCSI hot-swap drive bays are available.
For instructions on installing hard drives, see “Removing and Installing Hot Swap
Drive(s)” on page 42.
Note: Drives can consume up to 17 watts of power each. Drives must be specified to run at a
maximum ambient temperature of 45C.
The Intel® Server Chassis SC5400 does not support all SAS, SATA, or SCSI hard drives.
See “Additional Information and Software” on page ix for an Internet link to a list of
supported hardware.
Floppy / CD-ROM / DVD-ROM Slimline Carriers
For installation instructions on installing a floppy drive see “Installing and Removing a
Slimline USB Floppy/CD/DVD Combo Kit” on page 26. For installation instructions on
installing a CD-ROM drive or DVD-ROM drive, see “Removing and Installing a DVD or
CD-ROM Drive” on page 27.
To use one of the drives provided by Intel, use the following order codes:
• Slimline CD-ROM Drive: AXXSCD
• Slimline DVD/CDR Drive: AXXDVDCDR
• Slimline Floppy Drive: AXXCDUSBFDBRK
Note: The Intel® Server Chassis SC5400 does not support all slimline floppy, CD-ROM or
DVD-ROM hard drives. See “Additional Information and Software” on page ix for an
Internet link to a list of supported hardware. Intel provides accessory kits for these drives.
12
Intel® Server Chassis SC5400 User’s Guide
Intel® Remote Management Module
The Intel® Remote Management Module is available to provide advanced system
management features.
For installation instructions on installing the Intel® Remote Management Module, see the
instructions provided with the module.
Note: Some server boards may not support the Intel® Remote Management Module. See your
server board documentation to determine if this feature is compatible with your server
board.
Rack-mounted Systems
Your Intel® Server Chassis SC5400 can be mounted into a rack. Intel provides a tool-less
rail kit and a cable management arm to mount this server chassis into a rack. When
installing the chassis into a rack, Intel recommends you install systems from the bottom of
the rack to the top. In other words, install the first system in the rack into the bottom
position of the rack, the second system in the second position from the bottom, and so on.
Instructions for installing your chassis into a rack are included in the rail kit.
The order numbers are as follows:
• Tool-less Rail Kit: ARIGRACK
• Cable Management Arm: AXXRACKCARM (requires the tool-less rail kit)
Intel® Server Chassis SC5400 User’s Guide
13
14
Intel® Server Chassis SC5400 User’s Guide
2
Hardware Installations and
Upgrades
Before You Begin
Before working with your server product, pay close attention to the “Safety Information”
on page iii.
This document provides instructions for adding and replacing chassis components. For
instructions on replacing components on the server board, such as the processor and
memory DIMMs, see the instructions provided with the server board.
Tools and Supplies Needed
• Phillips* (cross head) screwdriver (#1 bit and #2 bit)
• Needle nosed pliers
• Anti-static wrist strap and conductive foam pad (recommended)
System References
All references to left, right, front, top, and bottom assume the reader is facing the front of
the chassis as it would be positioned for normal operation.
Intel® Server Chassis SC5400 User’s Guide
15
Removing and Installing the Chassis Cover
Removing the Chassis Cover
The Intel® Server Chassis SC5400 must be operated with the top cover in place to ensure
proper cooling. You will need to remove the top cover to add or replace components
inside of the platform. Before removing the top cover, power down the server and unplug
all peripheral devices and the AC power cable.
Note: A non-skid surface or a stop behind the chassis may be needed to prevent the chassis from
sliding on your work surface.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord.
4. Remove the access cover screw if it is installed (see letter "A" in the following
figure). While holding in the blue button at the top of the chassis (see letter "B"),
slide the top cover back until it stops. Lift the cover outward to remove it.
B
B
A
A
AF000555
Figure 7. Removing the Chassis Cover
16
Intel® Server Chassis SC5400 User’s Guide
Installing the Chassis Cover
1. Slide the chassis cover on the chassis.
2. Latch the cover securely to the chassis.
3. If the chassis will be re-shipped, secure the chassis cover to the chassis with the
access cover screw (see letter “A” in the following figure).
A
A
AF000572
Figure 8. Installing the Chassis Cover
Intel® Server Chassis SC5400 User’s Guide
17
Removing and Installing the Front Bezel
Removing the Bezel Assembly (Pedestal Only)
Caution: Do not rotate the bezel assembly more than 40 degrees or you will damage the bezel
assembly.
Note: The bezel assembly consists of two components, a front door and a sub-bezel.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Release the two plastic tabs (see letter “A” in the following figure) on the left side
of the bezel assembly to disengage the tabs.
5. Rotate the bezel assembly (see letter “B”) no more than 40 degrees outward.
6. At a 40-degree angle, push the bezel assembly away from the chassis (see letter
“C”).
7. If the bezel assembly does not immediately disconnect from the chassis, tap the
left-hand side of the bezel assembly to disengage the bezel hooks on the right-hand
side of the chassis.
A
C
A
B
AF000557
Figure 9. Removing the Front Bezel
18
Intel® Server Chassis SC5400 User’s Guide
Installing the Front Bezel (Pedestal Only)
Caution: This step applies to a pedestal configuration chassis only. For instructions on installing a
bezel in a rack-mount configuration, refer to the Rack Conversion kit Installation Guide:
Intel® Server Chassis SC5400.
1. Open the outer bezel door of the bezel assembly (see letter “A” in the following
figure).
2. Remove the filler panels that correspond to installed devices (see letter “B”).
3. Close the outer bezel door (see letter “C”).
4. Fit the right edge of the bezel assembly against the right side of the chassis.
5. Engage the plastic bezel hooks (see letter “D”) into the raised metal slots at the
chassis edge.
6. Rotate the bezel assembly toward the chassis.
7. Latch the two plastic tabs (see letter “E”) on the left side of the bezel assembly to
the chassis.
D
B
E
A
C
E
40° Max
AF000558
Figure 10. Installing the Front Bezel
Intel® Server Chassis SC5400 User’s Guide
19
Removing and Installing the Processor and
Memory Air Ducts
Always operate your server chassis with the processor and memory air ducts in place. The
air ducts are required for proper airflow within the chassis.
For instructions on adding or replacing a processor, first remove the processor and
memory air ducts, and then see your server board user guide for instructions on processor
installations and removals. Return to these instructions to reinstall the processor and
memory air ducts after installing your processor and heat sink.
Removing the Processor and Memory Air Ducts
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Press the latch on the memory air duct to disengage it from the server board (see
letter “A” in the following figure).
5. Detach the memory air duct from the processor air duct (see letter “B”).
6. Remove the processor air duct (see letter “C”).
A
B
C
AF000321
Figure 11. Removing the Processor and Memory Air Ducts
20
Intel® Server Chassis SC5400 User’s Guide
Installing the Processor and Memory Air Ducts
1. If your system has two processors, remove the inner plastic air baffle from the
inside of the processor air duct (see letter “A” in the following figure).
Caution: This step only applies to systems with two processors. If your server board has only one
processor installed, leave the inner air baffle in place and proceed to step two.
A
AF000323
Figure 12. Removing Inner Plastic Air Baffle from Processor Air Duct
2. Install the processor air duct. Make sure the tabs on the processor air duct (see
letters “A” and “B” in the following figure) engage their matching slots on the
chassis before inserting tabs into the chassis slots.
3. Install the memory air duct next by holding the large tab-end of the memory air
duct at a downward angle and then inserting the large tab (see letter “C”) from the
underside into the matching slot on the processor air duct.
Intel® Server Chassis SC5400 User’s Guide
21
4. Rotate the memory air duct downward until the two small tabs (see letter “D”)
engage and the memory air duct latch (see letter “E”) snaps into place.
B
A
B
A
1
D
2
C
D
E
A
E
AF000325
Figure 13. Installing the Processor and Memory Air Ducts
Caution: The processor air duct interlocks with the memory air duct in two places before latching
into place.
Note: Use care to avoid pinching the cables.
22
Intel® Server Chassis SC5400 User’s Guide
Replacing a Fixed Fan (Intel® Server Chassis
SC5400Base SC5400BRP only)
Note: This procedure applies only to the Intel® Server Chassis SC5400 BASE and Intel® Server
Chassis SC5400BRP configurations. The Intel® Server Chassis SC5400LX and
SC5400LXi ship with hot-swap fans.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Disconnect the appropriate fan power cable from the server board.
5. Remove the 92-mm (see letter “A” in the following figure) or 120-mm (see letter
“B”) fixed fan from its snap-in bracket.
A
92-mm
Fixed Fan
B
120-mm
Fixed Fan
TP00991
Figure 14. Removing a Fixed Fan
6. Install new 92-mm or 120-mm fixed fan.
7. Connect fan power cable to the server board. See the Intel® server board Quick
Start User’s Guide or User Guide for appropriate connection location.
8. Re-install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
9. Plug all peripheral devices and the AC power cable into the server and then power
up the server.
Intel® Server Chassis SC5400 User’s Guide
23
Removing and Installing Hot Swap Fans (Intel®
Server Chassis SC5400LX or SC5400LXi Only)
Removing Hot Swap Fans
Note: This procedure applies only to the Intel® Server Chassis SC5400LX and SC5400LXi
configurations. The Intel® Server Chassis SC5400 BASE and Intel® Server Chassis
SC5400BRP configurations ship with fixed fans.
The hot-swap fans from the Intel® Server Chassis SC5300LX cannot be used in the Intel®
Server Chassis SC5400LX or SC5400LXi.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
3. Press latch on fan (see letter “A” in the following figure) and pull on handle to
remove hot swap fan from chassis.
4. Repeat previous step for removal of remaining hot swap fans.
A
AF000573
Figure 15. Removing Hot Swap Fan
24
Intel® Server Chassis SC5400 User’s Guide
Installing Hot Swap Fans
Note: This procedure applies only to the Intel® Server Chassis SC5400LX or SC5400LXi
configurations. The Intel® Server Chassis SC5400 BASE and Intel® Server Chassis
SC5400BRP configurations ship with fixed fans.
The hot-swap fans from the Intel® Server Chassis SC5300 LX cannot be used in the Intel®
Server Chassis SC5400LX or SC5400LXi.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Remove the chassis cover if not removed in a previous step. For instructions, see
“Removing the Chassis Cover” on page 16.
3. Insert the hot swap fan into the chassis until it latches into place.
4. Repeat previous step for insertion of remaining hot swap fans.
AF000574
Figure 16. Installing Hot Swap Fan
Intel® Server Chassis SC5400 User’s Guide
25
Installing and Removing a Slimline USB Floppy/
CD/DVD Combo Kit
Installing a Slimline USB Floppy/CD/DVD Slimline Kit
Refer to the Slimline USB Floppy/CD-ROM/DVD-ROM Drive Kit Install Guide that
shipped with your slimline combo kit for installation instructions.
Removing a Slimline USB Floppy/CD/DVD Combo
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Disconnect the power and data cables to the slimline combo drive assembly.
6. Remove the combo drive/slide assembly from the chassis by pressing in on the
slide release latches (see letter “A” in the following figure). Remove the slides from
the slimline combo drive tray by pulling the slides away from the tray (see letter
“B”). A gentle pull should release the slide from the side dimple on the drive tray.
A
B
A
B
AF000575
Figure 17. Removing Slide/Drive Assembly from Upper Device Bay
26
Intel® Server Chassis SC5400 User’s Guide
7. If not replacing with another drive, re-attach pair of slides to an EMI shield and reinsert EMI shield/slide assembly into chassis for proper airflow.
AF000605
Figure 18. Re-inserting Empty EMI Shield/Slide Assembly into Chassis
8. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
9. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
10. Plug all peripheral devices and the AC power cable into the server.
11. Power up the server.
Removing and Installing a DVD or CD-ROM
Drive
Removing a DVD or CD-ROM Drive
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Disconnect the power and data cables to the DVD/CD-ROM drive.
Intel® Server Chassis SC5400 User’s Guide
27
6. Remove the DVD/CD-ROM drive/slide assembly from the chassis by pressing in
on the slide release latches (see letter “A” in the following figure). Remove the
slides from the DVD or CD-ROM drive by pulling the slides away from the drive
(see letter “B”). A gentle pull should release the slide from the side dimple on the
drive.
A
B
A
B
AF000575
7. If not replacing with another drive, re-attach pair of slides to an EMI shield and reinsert EMI shield/slide assembly into chassis for proper airflow.
AF000605
Figure 19. Re-inserting Empty EMI Shield/Slide Assembly into Chassis
8. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
9. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
10. Plug all peripheral devices and the AC power cable into the server.
11. Power up the server.
28
Intel® Server Chassis SC5400 User’s Guide
Installing a DVD or CD-ROM Drive
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Remove an EMI shield/slide assembly from the upper device bay by pressing the
two slide assembly latches inward (see letter “A” in the following figure). Remove
the slides from the EMI shield by pulling the slides away from the EMI shield to
release them from the EMI shield (see letter “B”).
A
B
A
B
AF000945
Figure 20. Removing EMI Shield/Slide Assembly from Upper Device Bay
6. Attach slides to the DVD or CD-ROM drive by pressing the slides firmly into the
side dimples on the DVD or CD-ROM drive.
AF000576
Figure 21. Attaching Slides to a DVD or CD-ROM Drive
Intel® Server Chassis SC5400 User’s Guide
29
7. Insert the drive/slide assembly into the upper device bay until the slides lock into
place.
8. Connect power and data cables.
9. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
10. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
11. Plug all peripheral devices and the AC power cable into the server.
12. Power up the server.
Removing and Installing Fixed Hard Drive(s)
Removing Fixed Hard Drive(s)
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Push the blue plastic release mechanism upward to release the fixed drive cage (see
letter “A” in the following figure).
6. Remove power and data cables from the hard drive connectors.
7. Pull the drive cage out about two inches (see letter “B”) so that it is partially
exposed from the drive bay slot in the chassis. Partially exposing the drive cage will
make it easier to open the upper door of the drive cage.
Note: As an alternative, you may also fully remove the drive cage from its drive bay
slot in the chassis. Take care, however, to position the drive cage horizontally
before opening the drive cage doors or the drive rails will spill out.
30
Intel® Server Chassis SC5400 User’s Guide
A
B
TP00906
Figure 22. Removing Six-drive Fixed Drive Cage from Chassis
8. Loosen the thumb screw (see letter “A” in the following figure). Open the upper
door of the drive cage (see letter “B”).
B
A
AF000579
Figure 23. Unlocking and Opening Upper Door of Fixed Drive Cage
Intel® Server Chassis SC5400 User’s Guide
31
9. Open the lower door.
AF000946
Figure 24. Opening Lower Door of Fixed Drive Cage
10. Remove the drive/slide assembly from the drive cage.
AF000588
Figure 25. Removing Drive/Slide Assembly from Drive Cage
32
Intel® Server Chassis SC5400 User’s Guide
11. Remove the device slides from hard drive. If not replacing hard drive, insert empty
device slides into drive cage.
AF000947
Figure 26. Inserting Empty Device Slides into Drive Cage
12. Close the lower door of drive cage.
AF000948
Figure 27. Closing Lower Door of Fixed Drive Cage
Intel® Server Chassis SC5400 User’s Guide
33
13. Close the upper door.
AF000949
Figure 28. Closing Upper Door of Fixed Drive Cage
14. Tighten the captive screw.
AF000586
Figure 29. Tightening Thumb Screw
15. Reinstall fixed hard drive into chassis.
16. If other hard drives remain in the drive cage, reconnect power and data cables.
17. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
18. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
19. Plug all peripheral devices and the AC power cable into the server.
20. Power up the server.
34
Intel® Server Chassis SC5400 User’s Guide
Installing Fixed Hard Drive(s)
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Push the blue plastic release mechanism upward to release the fixed drive cage (see
letter “A” in the following figure). Pull the drive cage out about two inches (see
letter “B”) so that it is partially exposed from the drive bay slot in the chassis.
Partially exposing the drive cage will make it easier to open the upper door of the
drive cage.
Note: As an alternative, you may also fully remove the drive cage from its drive bay
slot in the chassis. Take care, however, to position the drive cage horizontally
before opening the drive cage doors or the drive rails will spill out.
A
B
TP00906
Figure 30. Removing Six-drive Fixed Drive Cage from Chassis
Intel® Server Chassis SC5400 User’s Guide
35
6. Loosen the captive screw (see letter “A” in the following figure). Open the upper
door (see letter “B”).
B
A
AF000579
Figure 31. Unlocking and Opening Upper Door of Fixed Drive Cage
7. Open the lower door.
AF000580
Figure 32. Opening Lower Door of Fixed Drive Cage
36
Intel® Server Chassis SC5400 User’s Guide
8. Remove a pair of device slides from the drive cage.
AF000581
Figure 33. Removing Slides from Drive Cage
9. Attach the device slides to the hard drive. This is a tool-less operation. Insert pins
on device slides into mounting holes on hard drive. Press firmly to secure device
slides to hard drive. Ensure that the metal tabs on the device slides are facing the
front of the hard drive and facing towards each other.
AF000582
Figure 34. Attaching Device Slides to Hard Drive
Intel® Server Chassis SC5400 User’s Guide
37
10. Insert the drive/slide assembly into the drive cage. Make sure the cable connector
end of the hard drive faces towards the rear of the drive cage.
AF000583
Figure 35. Inserting Drive/Slide Assembly into Drive Cage
11. Repeat above steps for installation of additional hard drives into the drive cage.
12. Close the lower door of drive cage.
.
AF000584
Figure 36. Closing Lower Door of Fixed Drive Cage
38
Intel® Server Chassis SC5400 User’s Guide
13. Close the upper door of drive cage.
AF000585
Figure 37. Closing Upper Door of Fixed Drive Cage
14. Tighten the captive screw.
AF000586
Figure 38. Tightening Captive Screw
15. Re-install fixed drive cage into chassis.
16. Connect power and data cables to connectors on hard drive(s).
17. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
18. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
19. Plug all peripheral devices and the AC power cable into the server.
20. Power up the server.
Intel® Server Chassis SC5400 User’s Guide
39
Routing Power Cables to Fixed Drives
P2
Power Cable Routing
Chassis Primary Side View
To Upper Device Bay
To Server Board
To 4-Drive
Cage
To 6-Drive
Cage
Cable
Slot
PCI Add-in
card retainer
detail
AF000510
Figure 39. Routing Power Cables to Fixed Drives
Route longest power cables to the 6-drive bay and shorter cables to the 4-drive bay and
upper device bay.
Power Cable Routing Guidelines:
• P3, P4 and P5 power cables route to removable drives.
• P6, P7, P8, P9, P10 and P11 power cables (standard SAS/SATA); route as
appropriate.
• P12 and P13 power cables (SATA); route as appropriate.
40
Intel® Server Chassis SC5400 User’s Guide
Routing Data Cables to Fixed Drives
Note: Front panel, USB and one IDE cable are pre-routed by the factory. SAS or SATA cables
are supplied with the server board and hot-swap drive accessory kits. No cables are
supplied with the fixed drive bay kit.
• Route SAS/SATA data cables through the chassis openings located near the bottom
of the drive cage.
• Connect data cables to the respective fixed drive and to the appropriate connector on
the server board.
SAS/SATA Cable Routing
Chassis Primary Side View
SAS/SATA
To 4-Drive
Cage
IDE/USB/Front Panel Cables
4/6 Drive
Bay Cables
Chassis Primary Side View
To 6-Drive Cage
AF000509
Figure 40. Routing SAS/SATA Data Cables
Intel® Server Chassis SC5400 User’s Guide
41
Removing and Installing Hot Swap Drive(s)
Removing Hot Swap Drive(s)
1. Rotate the black lever downwards to unlatch the drive carrier. With the black lever
open, remove the drive carrier from the drive cage.
AF000593
Figure 41. Releasing Drive Carrier from Hot Swap Cage
2. Remove the four screws securing the hard drive to the drive carrier. Remove the
hard drive from the drive carrier.
AF000595
Figure 42. Removing Hard Drive from Drive Carrier
42
Intel® Server Chassis SC5400 User’s Guide
3. If not replacing with another hard drive, re-install the plastic air baffle into the
empty drive carrier. Secure the plastic air baffle to the drive carrier using the four
screws that were formerly attached to the hard drive.
Note: Plastic air baffles are necessary in all empty drive carriers to ensure proper
airflow within the chassis.
AF000950
Figure 43. Installing Plastic Air Baffle in Drive Carrier
4. With the black lever open, insert the drive carrier into the drive cage. Once inserted,
rotate the black lever upwards to latch the drive carrier into position.
AF000592
Figure 44. Inserting Drive Carrier into Hot Swap Cage
Intel® Server Chassis SC5400 User’s Guide
43
Installing Hot Swap Drive(s)
1. Press in on the green latch (see letter “A” in the following figure) at the end of the
drive carrier to disengage it from the hot swap drive cage.
2. Pull out on the black lever (see letter “B”) to fully open the drive carrier. When the
lever reaches a fully opened position, it will push the drive carrier out from the hot
swap drive cage. Slide the drive carrier out of the drive cage (see letter “C”).
A
B
C
AF000589
Figure 45. Removing Drive Carrier from Hot Swap Cage
3. Remove the four screws that secure the plastic air baffle to the drive carrier.
Remove the plastic air baffle.
AF000590
Figure 46. Removing Plastic Air Baffle
4. Secure the hard drive to the drive carrier using the four screws that were formerly
attached to the plastic air baffle. Ensure that the connector end of the hard drive is
facing the back of the drive carrier. The label side of the hard drive should be facing
up in the drive carrier.
44
Intel® Server Chassis SC5400 User’s Guide
AF000591
Figure 47. Securing Hard Drive to Drive Carrier
5. With the black lever open, insert the drive carrier into the drive cage. Once inserted,
rotate the black lever upwards to latch the drive carrier into position.
AF000592
Figure 48. Inserting Drive Carrier into Hot Swap Cage
Removing and Installing PCI Add-in Board(s)
Removing PCI Add-in Board(s)
Caution: When removing a full-length add-in card, you must pull back the latch on the plastic card
guide at the front of the chassis to release the card from the card guide.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Remove any cables attached to the add-in card, if necessary.
6. Remove the PCI add-in card retainer. Press in on the two plastic tabs (see letter “A”
in the following figure) to release the PCI add-in card retainer from the chassis.
Intel® Server Chassis SC5400 User’s Guide
45
Open the back panel PCI add-in card retention device (see letter “B”) by pressing
open from the inside of the chassis.
A
A
B
AF000600
Figure 49. Preparing Chassis for Removal of PCI Add-in Board
46
Intel® Server Chassis SC5400 User’s Guide
7. Firmly grab the PCI add-in board by its top edge or outer corners and remove from
the expansion slot on the server board. Place the removed PCI add-in board in an
anti-static protective wrapper. Close the back panel PCI add-in card retention
device.
8. Remove additional PCI add-in boards as necessary. When done, reinstall the PCI
add-in card retainer and close the PCI add-in card retention device(s).
9. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
10. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
11. Plug all peripheral devices and the AC power cable into the server.
12. Power up the server.
Installing PCI Add-in Board(s)
Caution: You may want to install an operating system before installing any add-in boards.
Do not overload the server board by installing add-in boards that draw excessive current.
Add-in boards can be extremely sensitive to ESD and always require careful handling.
After removing the board from its protective wrapper, place it component side up on a
grounded, static-free surface. Do not slide the board over any surface.
When removing a full-length add-in card, you must pull back on the latch on the plastic
card guide at the front of the chassis to release the card from the card guide.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
Intel® Server Chassis SC5400 User’s Guide
47
5. Press in on the two plastic tabs (see letter “A” in the following figure) and remove
the PCI add-in card retainer. Open the back panel PCI add-in card retention device
(see letter “B”) by pressing open from the inside of the chassis. Remove the PCI
slot shield (see letter “C”), if it has not already been removed, by pushing the shield
out from the inside of the chassis
A
A
B
C
AF000954
Figure 50. Preparing Chassis for Addition of PCI Add-in Board
6. Remove the PCI add-in board from its protective wrapper. Be careful not to touch
the components or gold edge connectors. Place the add-in board on an anti-static
surface. Record the type and serial number of the add-in board in your equipment
log. Set the jumpers or switches on the board according to the manufacturer’s
instructions.
48
Intel® Server Chassis SC5400 User’s Guide
7. Hold the PCI add-in board by its top edge or upper corners. Firmly press the add-in
board into an expansion slot on the server board (see letter “A” in the following
figure). Close the back panel PCI add-in card retention device (see letter “B”).
A
B
AF000599
Figure 51. Installing Add-in Board
8. Repeat steps 2-10 until all the PCI add-in cards are installed.
Intel® Server Chassis SC5400 User’s Guide
49
9. Reinstall the PCI Add-in Card Retainer.
AF000600
Figure 52. Reinstalling PCI Add-in Card Retainer
10. Attach cables if necessary.
11. Install the front bezel. For instructions, see “Removing and Installing the Front
Bezel” on page 18.
12. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
13. Plug all peripheral devices and the AC power cable into the server.
14. Power up the server.
50
Intel® Server Chassis SC5400 User’s Guide
Installing Additional Hot Swap Power Supply
Module
Caution: This step only applies to a chassis with redundant power supply capability. Do not
perform this step if your chassis has a fixed power supply.
1. Remove screws (see letter “A” in the following figure). Remove the power supply
filler panel (see letter “B”).
A
A
B
AF000602
Figure 53. Removing Power Supply Filler Panel
2. Insert the power supply module until it clicks into place. Secure with screw (see
letter “A” in the following figure) if shipping chassis to another location.
A
AF000603
Figure 54. Installing Additional Hot Swap Power Supply Module
Intel® Server Chassis SC5400 User’s Guide
51
Replacing a Hot Swap Power Supply
Warning: Hazardous voltage, current, and energy levels are present inside the power supply. There
are no user-serviceable parts inside it; servicing should be done by technically qualified
personnel.
1. Remove the power cable from the defective hot swap power supply.
2. If present, remove shipping screw securing defective hot swap power supply to
chassis (see letter “A” in the following figure). Press on green latch (see letter “B”)
while pulling on handle to remove power supply from chassis.
A
B
AF000956
Figure 55. Removing Hot Swap Power Supply from Chassis
3. Insert new hot swap power supply into chassis. Replace shipping screw (see letter
“A” in the following figure) if shipping chassis to another location.
A
AF000603
Figure 56. Installing Hot Swap Power Supply into Chassis
4. Connect power cable to replaced power supply.
52
Intel® Server Chassis SC5400 User’s Guide
Replacing a Fixed Power Supply
Warning: Hazardous voltage, current, and energy levels are present inside the power supply. There
are no user-serviceable parts inside it; servicing should be done by technically qualified
personnel.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Disconnect all internal power cables from chassis components and server board.
5. Remove the eight screws securing the fixed power supply shield to the chassis (see
letter “A” in the following figure). Remove the fixed power supply (see letter “B”).
B
A
AF000957
Figure 57. Removing Fixed Power Supply
6. Insert new fixed power supply.
7. Secure the fixed power supply shield to the chassis with the eight screws.
8. Connect the P1, P14, and P16 cables to the server board. See the Intel® server
board Quick Start User’s Guide or User Guide for connection locations.
9. Reconnect power cables to other chassis components as appropriate.
10. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
11. Plug all peripheral devices and the AC power cable into the server.
12. Power up the server.
Intel® Server Chassis SC5400 User’s Guide
53
Replacing the Power Distribution Board
Warning: Hazardous voltage, current, and energy levels are present inside the power supply. There
are no user-serviceable parts inside it; servicing should be done by technically qualified
personnel.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the memory and processor air ducts. For instructions, see “Removing the
Processor and Memory Air Ducts” on page 20.
5. If present, remove shipping screw securing hot swap power supply to chassis (see
letter “A” in the following figure). Press on green latch (see letter “B”) while
pulling on handle to remove power supply from chassis. Repeat this step for the
second hot swap power supply if one is installed.
A
B
AF000956
Figure 58. Removing Hot Swap Power Supply from Chassis
6. Disconnect all internal power cables from chassis components and server board.
54
Intel® Server Chassis SC5400 User’s Guide
7. Remove screw (see letter “A” in the following figure) securing center divider to the
power supply cage. Push center divider straight back (see letter “B”) to release tabs
from chassis slots. Then, while holding the right edge of the center divider at a
downward angle, disengage tabs from chassis wall by pushing center divider up
and sideways (see letter “C”). Remove center divider from power supply cage (see
letter “D”).
A
B
C
D
TP00696
Figure 59. Removing Center Divider
Intel® Server Chassis SC5400 User’s Guide
55
8. Loosen thumb screw (see letter “A” in the following figure) securing the power
distribution board to the chassis. Lift the power distribution board off of the
standoffs (see letter “B”) and then remove it through the back of the power supply
cage (see letter “C”). You may have to feed the power cables through the power
supply cage while removing the power distribution board.
B
A
C
TP00698
Note: Cables on back of power distribution board not shown to clarify insertion process.
Figure 60. Removing Power Distribution Board
56
Intel® Server Chassis SC5400 User’s Guide
9. Insert new power distribution board into power supply cage (see letter “A” in the
following figure). Try to route the power cables to the appropriate area at the time
of insertion (see Steps 9 and 10 below). Position the power distribution board on the
four standoffs inside the power supply cage. Push down on the power distribution
board to securely attach it to the standoffs (see letter “B”). Tighten thumb screw
(see letter “C”).
B
C
A
TP00693
Note: Cables on back of power distribution board not shown to clarify insertion process.
Figure 61. Securing Power Distribution Board to Power Supply Cage
10. Connect the P1, P14, and P16 cables to the server board. See the Intel® server
board Quick Start User’s Guide or User Guide for appropriate connection
locations.
11. Reconnect power cables to other chassis components as appropriate.
Intel® Server Chassis SC5400 User’s Guide
57
12. Reinstall center divider (see letter “A” in the following figure) and secure to chassis
with one screw (see letter “B”).
B
A
C
TP00843
Figure 62. Re-installing Center Divider
13. Insert hot swap power supply(ies) into chassis. Replace shipping screw(s) (see
letter “A” in the following figure) if shipping chassis to another location.
A
AF000603
Figure 63. Installing Hot Swap Power Supply into Chassis
58
Intel® Server Chassis SC5400 User’s Guide
14. Re-install the memory and processor air ducts. For instructions, see “Installing the
Processor and Memory Air Ducts” on page 21.
15. Re-install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
16. Plug all peripheral devices and the AC power cable into the server.
17. Power up the server.
Replacing the Control Panel
The steps for replacing the front control panel and the Intel® Local Control Panel are
nearly identical. Use the following steps for both varieties of the control panel. Where
necessary, differences between the two control panels are noted.
Your server must be operated with a control panel installed.
Caution: The control panel is NOT hot swappable. Before removing or replacing the control panel,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel if it is installed. For instructions, see “Removing and
Installing the Front Bezel” on page 18.
5. Press the latch at the back of the control panel.
6. Slide the control panel out through the front of the chassis far enough so that you
can reach the front panel and USB cable connectors at the rear of the control panel.
7. Disconnect cables.
8. Install the control panel module into the chassis.
9. Reconnect cables.
10. (Optional) Install the front bezel. For instructions, see “Removing and Installing the
Front Bezel” on page 18.
11. Install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
12. Plug all peripheral devices and the AC power cable into the server.
13. Power up the server.
Intel® Server Chassis SC5400 User’s Guide
59
Installing and/or Removing a Server Board
Note: The server board you can install in your chassis depends upon the chassis model.
To install or remove a server board, do the following:
1. Observe the safety and ESD precautions at the beginning of this book.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover” on
page 16.
4. Remove the front bezel assembly if it is installed. For instructions, see “Removing
the Bezel Assembly (Pedestal Only)” on page 18.
5. Remove any PCI add-in boards that are present. For instructions, see “Removing
PCI Add-in Board(s)” on page 45.
6. Remove the processor and memory air ducts. For instructions, see “Removing the
Processor and Memory Air Ducts” on page 20.
7. If installing a server board, refer to the User Guide and/or Quick Start User’s Guide
that shipped with your Intel® server board for installation instructions. Use the
mounting screws, bumpers and standoffs (if necessary) that came with your chassis
to secure the server board to the chassis. Make sure the server board is properly
seated and then tighten the screws firmly, starting with the screws at the center of
the server board. Make cable connections per instructions in the Intel® server board
User Guide and/or Quick Start User’s Guide.
8. If removing a server board, disconnect all cables connected to the server board.
Remove the mounting screws, starting with the screws at the center of the server
board. Remove the server board.
9. Re-install the processor and memory air ducts. For instructions, see “Installing the
Processor and Memory Air Ducts” on page 21.
10. If desired, install any PCI Add-in boards. For instructions, see “Installing PCI Addin Board(s)” on page 47.
11. Re-install the front bezel assembly. For instructions, see “Installing the Front Bezel
(Pedestal Only)” on page 19.
12. Re-install the chassis cover. For instructions, see “Installing the Chassis Cover” on
page 17.
13. Plug all peripheral devices and the AC power cable into the server.
14. Power up the server.
60
Intel® Server Chassis SC5400 User’s Guide
Connecting and Disconnecting Cables to or
from Server Board
Caution: Use caution when routing cables to ensure that cables do not obstruct fan airflow.
1. See your Intel® Server Board User Guide or Quick Start User’s Guide for cable
connection locations.
2. If your server has a hot swap power supply, secure the cables (that route toward the
server board) to the chassis.
Connecting Cables to Server Board
1. If your server has a hot swap power supply, connect the cables (that route toward
the server board) to the chassis.
2. See your Intel® Server Board User Guide or Quick Start User’s Guide for cable
connection locations.
Removing Cables from Server Board(s)
1. If your server has a hot swap power supply, remove the cables (that route toward
the server board) to the chassis.
2. See your Intel® Server Board User Guide or Quick Start User’s Guide for cable
connection locations.
Intel® Server Chassis SC5400 User’s Guide
61
62
Intel® Server Chassis SC5400 User’s Guide
3
Technical Reference
Power Supply Specifications
670-W Single Power Supply Input Voltages
• 100-127V at 50/60 Hz; 12A max.
• 200-240V at 50/60 Hz; 7A max.
670-W Single Power Supply Output Voltages
The following table lists the total wattage available from the power subsystem for each
voltage. Ensure that your loads do not exceed the combined total wattage of 670 Watts.
For information about calculating the power usage for your configuration, see
“Calculating Power Usage” on page 65.
Table 6. 670-W Power Supply Output Capability
Voltage
Maximum Current
+3.3 V
24 A
+5.0 V
30 A
+5 V Standby
3A
+12.0
48 A
-12.0 V
0.5 A
Warning: Do not exceed a combined power output of 170 Watts for the +5 V and +3.3 V outputs.
Exceeding a combined 170 Watts will overload the power subsystem and may cause the
power supplies to overheat and malfunction.
The expansion slots on the server board are rated for no more than 25 Watts for any one
slot. The average current usage per slot should not exceed 13 Watts.
830-W Single Power Input Voltages
• 100-127 V∼at 50/60 Hz; 14 A max.
• 200-240 V∼at 50/60 Hz; 8 A max.
Intel® Server Chassis SC5400 User’s Guide
63
830-W Single Power Supply Output Voltages
The following table lists the total wattage available from the power subsystem for each
voltage. If you configure your system heavily, ensure that your loads do not exceed the
combined total wattage of 800 Watts. For information about calculating the power usage
for your configuration, see “Calculating Power Usage” on page 65.
Table 7. 830-W Power Supply Output Capability
Voltage
Maximum Current
+3.3 V
25 A
+5.0 V
33 A
+5 V Standby
3A
+12.0
51 A
-12.0 V
0.5 A
Warning: Do not exceed a combined power output of 170 Watts for the +5 V and +3.3 V outputs.
Exceeding a combined 170 Watts will overload the power subsystem and may cause the
power supplies to overheat and malfunction.
The expansion slots on the server board are rated for no more than 25 Watts for any one
slot. The average current usage per slot should not exceed 13 Watts.
System Environmental Specifications
Table 8. Environmental Specifications
Non-operating: -40 ° to 70 °C.
Temperature
Humidity
Shock
Acoustic noise
Electrostatic discharge
(ESD)
64
Operating: 10 ° to 35 °C; derated 0.5 °C for every 1000 ft. (305 m) to
a maximum of 10,000 ft.
Non-operating: 90% relative humidity (non-condensing) at 30 °C.
Operating: 2.0 g, 11 msec, 1/2 sine
Packaged: Operational after an 18" free fall.
UP, DP, BRP configurations - 5.5 BA LWA idle; 6.0 BA LWA typical
operating
Tested to 15 kilovolts (kV); no component damage.
Intel® Server Chassis SC5400 User’s Guide
Current Usage
Calculating Power Usage
The total combined wattage for your configuration must be less than the wattage rating
for your power supply. Use the two worksheets in this section to calculate the total used
by your configuration. For current and voltage requirements of add-in boards and
peripherals, see your vendor documents.
Worksheet, Calculating DC Power Usage
Table 9. Power Usage Worksheet
Current (maximum) at voltage level:
Device
+3.3
V
+5 V
–5 V
+12
V
–12
V
5 V Standby
Baseboard, Front Panel
Board and Fans
Processor(s)
Memory
3.5-inch Diskette Drive
CD-ROM Drive
Second 5.25-inch Device
Third 5.25-inch Device
1st Hard Drive
2nd Hard Drive
3rd Hard Drive
4th Hard Drive
5th Hard Drive
6th Hard Drive
Expansion Board 1
Expansion Board 2
Expansion Board 3
Expansion Board 4
Expansion Board 5
Expansion Board 6
Intel® Remote Management
Module
Control Panel
Total Current
Intel® Server Chassis SC5400 User’s Guide
65
Worksheet, Total Combined Power Used by the Server
3. From the previous worksheet, enter the total current for each column.
4. Multiply the voltage by the total current to get the total wattage for each voltage
level.
Add the total wattage for each voltage level to arrive at the total combined power usage
for the power subsystem.
Table 10. Power Usage Worksheet 2
Voltage level and total current
(V X A = W)
Total Watts
for each voltage level
(+3.3 V) X (______ A)
________ W
(+5 V) X (______ A)
________ W
(+12 V) X (______ A)
________ W
(–12 V) X (______ A)
________ W
(5 V standby) X (______ A)
________ W
Total Combined Wattage
________ W
Caution: Do not exceed a combined power output of 170 Watts for the +5 V and +3.3 V outputs.
Exceeding a combined 170 Watts will overload the power subsystem and may cause the
power supplies to overheat and malfunction.
66
Intel® Server Chassis SC5400 User’s Guide
Appendix B: Regulatory and
Compliance Information
Product Regulatory Compliance
Warning: To ensure regulatory compliance, you must adhere to the assembly instructions in this
guide to ensure and maintain compliance with existing product certifications and
approvals. Use only the described, regulated components specified in this guide. Use of
other products/components will void the UL listing and other regulatory approvals of the
product and will most likely result in noncompliance with product regulations in the
region(s) in which the product is sold.
To help ensure EMC compliance with your local regional rules and regulations, before
computer integration, make sure that the server system, power supply, and other modules
have passed EMC testing using a server board with a microprocessor from the same
family (or higher) and operating at the same (or higher) speed as the microprocessor used
on this server board. The final configuration of your end system product may require
additional EMC compliance testing. For more information, please contact your local Intel
representative.
This is an FCC Class A device. Integration of it into a Class B system does not result in a
Class B device.
Product Safety Compliance
This server chassis product, when correctly integrated per this guide, complies with the
following safety and electromagnetic compatibility (EMC) regulations.
Intended Application
This product was evaluated as Information Technology Equipment (ITE), which may be
installed in offices, schools, computer rooms, and similar commercial type locations. The
suitability of this product for other product categories and environments (such as: medical,
industrial, telecommunications, NEBS, residential, alarm systems, test equipment, etc.),
other than an ITE application, may require further evaluation.
Intel® Server Chassis SC5400 User’s Guide
71
Product Regulatory Compliance References
The following table references Server Chassis Compliance and markings that may appear
on the product. Markings below are typical markings however, may vary or be different
based on how certification is obtained.
Note: Certifications Emissions requirements are to Class A.
Table 11. Product Regulatory Compliance Markings
Compliance Regional
Description
Australia / New Zealand
Compliance
Reference
Compliance Reference Marking Example
AS/NZS 3548
(Emissions)
N232
Argentina
IRAM
Certification
(Safety)
Belarus
Belarus
Certification
Canada / USA
CSA 60950 - UL
60950 (Safety)
Canada / USA
Industry Canada
ICES-003
(Emissions)
None Required
CANADA ICES-003 CLASS A
CANADA NMB-003 CLASSE A
FCC
CFR 47, Part 15
(Emissions)
China
CNCA - CB4943
(Safety)
GB 9254
(Emissions)
GB17625
(Harmonics)
72
Intel® Server Chassis SC5400 User’s Guide
Table 11. Product Regulatory Compliance Markings
Compliance Regional
Description
CENELEC Europe
Compliance
Reference
Compliance Reference Marking Example
Low Voltage
Directive 93/68/
EEC;
EMC Directive 89/
336/EEC
EN55022
(Emissions)
EN55024
(Immunity)
EN61000-3-2
(Harmonics)
EN61000-3-3
(Voltage Flicker)
CE Declaration of
Conformity
Germany
GS Certification EN60950
International
CB Certification IEC60950
None Required
CISPR 22 /
CISPR 24
Japan
VCCI Certification
Korea
RRL Certification
MIC Notice No.
1997-41 (EMC) &
1997-42 (EMI)
Intel® Server Chassis SC5400 User’s Guide
73
Table 11. Product Regulatory Compliance Markings
Compliance Regional
Description
Russia
Compliance
Reference
Compliance Reference Marking Example
GOST-R
Certification
GOST R 2921691 (Emissions)
GOST R 5062895 (Immunity)
Ukraine
Ukraine
Certification
Taiwan
BSMI CNS13438
None Required
R33025
74
Intel® Server Chassis SC5400 User’s Guide
Electromagnetic Compatibility Notices
FCC Verification Statement (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation
5200 N.E. Elam Young Parkway
Hillsboro, OR 97124-6497
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit other than the one to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment. The customer is responsible for
ensuring compliance of the modified product.
Only peripherals (computer input/output devices, terminals, printers, etc.) that comply
with FCC Class A or B limits may be attached to this computer product. Operation with
noncompliant peripherals is likely to result in interference to radio and TV reception.
All cables used to connect to peripherals must be shielded and grounded. Operation with
cables, connected to peripherals, that are not shielded and grounded may result in
interference to radio and TV reception.
Intel® Server Chassis SC5400 User’s Guide
75
Industry Canada (ICES-003)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:
"Apparelis Numériques", NMB-003 édictee par le Ministre Canadian des
Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the interference-causing equipment standard entitled: "Digital
Apparatus," ICES-003 of the Canadian Department of Communications.
Europe (CE Declaration of Conformity)
This product has been tested in accordance to, and complies with the Low Voltage
Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked
with the CE Mark to illustrate its compliance.
VCCI (Japan)
English translation of the preceding notice:
This is a Class A product based on the standard of the Voluntary Control Council for
Interference (VCCI) from Information Technology Equipment. If this is used near a radio
or television receiver in a domestic environment, it may cause radio interference. Install
and use the equipment according to the instruction manual.
BSMI (Taiwan)
The BSMI Certification Marking and EMC warning is located on the outside rear area of
the product.
76
Intel® Server Chassis SC5400 User’s Guide
Korean Compliance (RRL)
Following is the RRL certification information for Korea.
English translation of the notice above:
1. Type of Equipment (Model Name): On License and Product
2. Certification No.: On RRL certificate. Obtain certificate from local Intel
representative
3. Name of Certification Recipient: Intel Corporation
4. Date of Manufacturer: Refer to date code on product
5. Manufacturer/Nation: Intel Corporation/Refer to country of origin marked on
product
CNCA (CCC-China)
The CCC Certification Marking and EMC warning is located on the outside rear area of
the product.
Product Ecology Compliance
Intel has a system in place to restrict the use of banned substances in accordance with
world wide product ecology regulatory requirements. The following is Intel's product
ecology compliance criteria.
Intel® Server Chassis SC5400 User’s Guide
77
Table 12. Product Ecology Compliance Markings
Compliance
Regional
Description
California
China
Compliance Reference
Marking Example
Compliance Reference
California Code of Regulations, Title 22,
Division 4.5; Chapter 33: Best
Management Practices for Perchlorate
Materials.
Special handling may apply. See
www.dtsc.ca.gov/
hazardouswaste/perchlorate.
This notice is required by
California Code of Regulations,
Title 22, Division 4.5; Chapter 33:
Best Management Practices for
Perchlorate Materials. This
product / part includes a battery
which contains Perchlorate
material.
China RoHS
Administrative Measures on the Control of
Pollution Caused by Electronic
Information Products" (EIP) #39. Referred
to as China RoHS.
Mark requires to be applied to retail
products only. Mark used is the
Environmental Friendly Use Period
(EFUP). Number represents years.
China Recycling (GB18455-2001)
Mark requires to be applied to be retail
product only. Marking applied to bulk
packaging and single packages. Not
applied to internal packaging such as
plastics, foams, etc.
78
Intel Internal
Specification
All materials, parts and subassemblies
must not contain restricted materials as
defined in Intel's Environmental Product
Content Specification of Suppliers and
Outsourced Manufacturers - http://
supplier.intel.com/ehs/environmental.htm
Europe
Waste Electrical and Electronic
Equipment (WEEE) Directive 2002/96/
EC - Mark applied to system level
products only.
None Required
Intel® Server Chassis SC5400 User’s Guide
Compliance
Regional
Description
Europe
Compliance Reference
European Directive 2002/95/EC -
Compliance Reference
Marking Example
None Required.
Restriction of Hazardous Substances
(RoHS). Threshold limits and banned
substances are noted below.
Quantity limit of 0.1% by mass (1000
PPM) for: Lead, Mercury, Hexavalent
Chromium, Polybrominated Biphenyls
Diphenyl Ethers (PBB/PBDE)
Quantity limit of 0.01% by mass (100
PPM) for: Cadmium
Germany
German Green Dot
Applied to Retail Packaging Only for
Boxed Boards
Intel Internal
Specification
International
All materials, parts and subassemblies
must not contain restricted materials as
defined in Intel's Environmental Product
Content Specification of Suppliers and
Outsourced Manufacturers - http://
supplier.intel.com/ehs/environmental.htm.
None Required
ISO11469 - Plastic parts weighing >25gm
are intended to be marked with per
ISO11469.
>PC/ABS<
Recycling Markings - Fiberboard (FB) and
Cardboard (CB) are marked with
international recycling marks. Applied to
outer bulk packaging and single package.
Japan
Japan Recycling
Applied to Retail Packaging Only for
Boxed Boards
Intel® Server Chassis SC5400 User’s Guide
79
Other Markings
Table 13. Other Markings
Compliance
Description
Compliance Reference
Marking Example
Compliance Reference
Stand-by
Power
Stand-by Power Warnings
Multiple Power
Cords
Multiple Power Cords Warnings
English:
Applied to product if more than one power
cord is used.
This unit has more than one
power supply cord. To reduce
the risk of electrical shock,
disconnect (2) two power supply
cords before servicing.
Applied to product if stand-by power
switch is used.
Simplified Chinese
注意:
本设备包括多条电源系统电缆。
为避免遭受电击,
在进行维修之前应断开两(2)
条电源系统电缆
Traditional Chinese
注意:
本設備包括多條電源系統電纜。
遭受電擊,
在進行維修之前應斷開兩(2)
條電源系統電纜
German:
Dieses Geräte hat mehr als ein
Stromkabel. Um eine Gefahr des
elektrischen Schlages zu
verringern trennen sie beide (2)
Stromkabeln bevor
Instandhaltung
80
Intel® Server Chassis SC5400 User’s Guide
Compliance
Description
Ground
Connection
Compliance Reference
Ground Connection Warnings
Compliance Reference
Marking Example
Line1 :
“WARNING:”
Swedish on line2:
“Apparaten skall anslutas till
jordat uttag, när den ansluts till
ett nätverk."
Finnish on line 3:
"Laite on liitettävä
suojamaadoituskoskettimilla
varustettuun pistorasiaan."
English on line 4:
"Connect only to a properly earth
grounded outlet."
Regulated Specified Components
To maintain the UL listing and compliance to other regulatory certifications and/or
declarations, the following regulated components must be used and conditions adhered to.
Interchanging or use of other components will void the UL listing and other product
certifications and approvals.
Updated product information for configurations can be found on the Intel Server Builder
Web site at the following URL: http://channel.intel.com/go/serverbuilder
If you do not have access to Intel's Web address, please contact your local Intel
representative.
• Server Chassis: (base chassis is provided with power supply and fans) - UL listed.
• Server board: you must use an Intel server board - UL recognized.
• Add-in boards: must have a printed wiring board flammability rating of minimum
UL94V-1. Add-in boards containing external power connectors and/or lithium
batteries must be UL recognized or UL listed. Any add-in board containing modem
telecommunication circuitry must be UL listed. In addition, the modem must have
the appropriate telecommunications, safety, and EMC approvals for the region in
which it is sold.
• Peripheral Storage Devices: must be a UL recognized or UL listed accessory and
TUV or VDE licensed. Total server configuration is not to exceed the maximum
loading conditions of the power supply.
Intel® Server Chassis SC5400 User’s Guide
81
End-of-Life / Product Recycling
Product recycling and end-of-life take-back systems and requirements vary by country.
Contact the retailer or distributor of this product for information about product recycling
and / or take-back.
82
Intel® Server Chassis SC5400 User’s Guide
Appendix E: Installation/Assembly
Safety Instructions
English
The power supply in this product contains no user-serviceable parts.
Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is
not the exact type required. A product with more than one power
supply will have a separate AC power cord for each supply.
The power button on the system does not turn off system AC power.
To remove AC power from the system, you must unplug each AC
power cord from the wall outlet or power supply.
The power cord(s) is considered the disconnect device to the main
(AC) power. The socket outlet that the system plugs into shall be
installed near the equipment and shall be easily accessible.
SAFETY STEPS: Whenever you remove the chassis covers to
access the inside of the system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall
outlets.
4. Label and disconnect all cables connected to I/O connectors
or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by
wearing an antistatic wrist strap attached to chassis ground of
the system-any unpainted metal surface-when handling
components.
6. Do not operate the system with the chassis covers removed.
Intel® Server Chassis SC5400 User’s Guide
117
After you have completed the six SAFETY steps above, you can
remove the system covers. To do this:
1. Unlock and remove the padlock from the back of the system if
a padlock has been installed.
2. Remove and save all screws from the covers.
3. Remove the cover(s).
For proper cooling and airflow, always reinstall the chassis covers
before turning on the system. Operating the system without the
covers in place can damage system parts. To install the covers:
1. Check first to make sure you have not left loose tools or parts
inside the system.
2. Check that cables, add-in boards, and other components are
properly installed.
3. Attach the covers to the chassis with the screws removed
earlier, and tighten them firmly.
4. Insert and lock the padlock to the system to prevent
unauthorized access inside the system.
5. Connect all external cables and the AC power cord(s) to the
system.
A microprocessor and heat sink may be hot if the system has been
running. Also, there may be sharp pins and edges on some board
and chassis parts. Contact should be made with care. Consider
wearing protective gloves.
Danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
equipment manufacturer. Dispose of used batteries according to
manufacturer's instructions.
The system is designed to operate in a typical office environment.
Choose a site that is:
•
•
•
•
•
•
•
118
Clean and free of airborne particles (other than normal room
dust).
Well ventilated and away from sources of heat including direct
sunlight.
Away from sources of vibration or physical shock.
Isolated from strong electromagnetic fields produced by
electrical devices.
In regions that are susceptible to electrical storms, we
recommend you plug your system into a surge suppresser and
disconnect telecommunication lines to your modem during an
electrical storm.
Provided with a properly grounded wall outlet.
Provided with sufficient space to access the power supply
cord(s), because they serve as the product's main power
disconnect.
Intel® Server Chassis SC5400 User’s Guide
Deutsch
Benutzer können am Netzgerät dieses Produkts keine Reparaturen
vornehmen. Das Produkt enthält möglicherweise mehrere
Netzgeräte. Wartungsarbeiten müssen von qualifizierten Technikern
ausgeführt werden.
Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu
verwenden, wenn es sich nicht genau um den erforderlichen Typ
handelt. Ein Produkt mit mehreren Netzgeräten hat für jedes
Netzgerät ein eigenes Netzkabel.
Der Wechselstrom des Systems wird durch den Ein-/Aus-Schalter
für Gleichstrom nicht ausgeschaltet. Ziehen Sie jedes
Wechselstrom-Netzkabel aus der Steckdose bzw. dem Netzgerät,
um den Stromanschluß des Systems zu unterbrechen.
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu
gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus der
Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie
alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um
elektrostatische Ladungen (ESD) über blanke Metallstellen
bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß
montiertes Gehäuse ein.
Intel® Server Chassis SC5400 User’s Guide
119
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu
gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus der
Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie
alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um
elektrostatische Ladungen (ESD) über blanke Metallstellen
bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß
montiertes Gehäuse ein.
Zur ordnungsgemäßen Kühlung und Lüftung muß die
Gehäuseabdeckung immer wieder vor dem Einschalten installiert
werden. Ein Betrieb des Systems ohne angebrachte Abdeckung
kann Ihrem System oder Teile darin beschädigen. Um die
Abdeckung wieder anzubringen:
1. Vergewissern Sie sich, daß Sie keine Werkzeuge oder Teile
im Innern des Systems zurückgelassen haben.
2. Überprüfen Sie alle Kabel, Zusatzkarten und andere
Komponenten auf ordnungsgemäßen Sitz und Installation.
3. Bringen Sie die Abdeckungen wieder am Gehäuse an, indem
Sie die zuvor gelösten Schrauben wieder anbringen. Ziehen
Sie diese gut an.
4. Bringen Sie die Verschlußeinrichtung (Padlock) wieder an und
schließen Sie diese, um ein unerlaubtes Öffnen des Systems
zu verhindern.
5. Schließen Sie alle externen Kabel und den AC
Stromanschlußstecker Ihres Systems wieder an.
Der Mikroprozessor und der Kühler sind möglicherweise erhitzt,
wenn das System in Betrieb ist. Außerdem können einige Platinen
und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten
an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie
sollten Schutzhandschuhe tragen.
Bei falschem Einsetzen einer neuen Batterie besteht
Explosionsgefahr. Die Batterie darf nur durch denselben oder einen
entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt
werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des
Herstellers entsprechend.
120
Intel® Server Chassis SC5400 User’s Guide
Das System wurde für den Betrieb in einer normalen Büroumgebung
entwickelt. Der Standort sollte:
•
•
•
•
•
•
•
Intel® Server Chassis SC5400 User’s Guide
"sauber und staubfrei sein (Hausstaub ausgenommen);
"gut gelüftet und keinen Heizquellen ausgesetzt sein
(einschließlich direkter Sonneneinstrahlung);
"keinen Erschütterungen ausgesetzt sein;
"keine starken, von elektrischen Geräten erzeugten
elektromagnetischen Felder aufweisen;
"in Regionen, in denen elektrische Stürme auftreten, mit einem
Überspannungsschutzgerät verbunden sein; während eines
elektrischen Sturms sollte keine Verbindung der
Telekommunikationsleitungen mit dem Modem bestehen;
"mit einer geerdeten Wechselstromsteckdose ausgerüstet sein;
"über ausreichend Platz verfügen, um Zugang zu den
Netzkabeln zu gewährleisten, da der Stromanschluß des
Produkts hauptsächlich über die Kabel unterbrochen wird
121
Français
Le bloc d'alimentation de ce produit ne contient aucune pièce
pouvant être réparée par l'utilisateur. Ce produit peut contenir plus
d'un bloc d'alimentation. Veuillez contacter un technicien qualifié en
cas de problème.
Ne pas essayer d'utiliser ni modifier le câble d'alimentation CA
fourni, s'il ne correspond pas exactement au type requis. Le nombre
de câbles d'alimentation CA fournis correspond au nombre de blocs
d'alimentation du produit
Notez que le commutateur CC de mise sous tension /hors tension
du panneau avant n'éteint pas l'alimentation CA du système. Pour
mettre le système hors tension, vous devez débrancher chaque
câble d'alimentation de sa prise.
CONSIGNES DE SÉCURITÉ -Lorsque vous ouvrez le boîtier pour
accéder à l'intérieur du système, suivez les consignes suivantes:
1. Mettez hors tension tous les périphériques connectés au
système.
2. Mettez le système hors tension en mettant l'interrupteur
général en position OFF (bouton-poussoir).
3. Débranchez tous les cordons d'alimentation c.a. du système
et des prises murales.
4. Identifiez et débranchez tous les câbles reliés aux
connecteurs d'E-S ou aux accès derrière le système.
5. Pour prévenir les décharges électrostatiques lorsque vous
touchez aux composants, portez une bande antistatique pour
poignet et reliez-la à la masse du système (toute surface
métallique non peinte du boîtier).
6. Ne faites pas fonctionner le système tandis que le boîtier est
ouvert.
Une fois TOUTES les étapes précédentes accomplies, vous pouvez
retirer les panneaux du système. Procédez comme suit:
1. Si un cadenas a été installé sur à l'arrière du système,
déverrouillez-le et retirez-le.
2. Retirez toutes les vis des panneaux et mettez-les dans un
endroit sûr.
3. Retirez les panneaux.
122
Intel® Server Chassis SC5400 User’s Guide
Afin de permettre le refroidissement et l'aération du système,
réinstallez toujours les panneaux du boîtier avant de mettre le
système sous tension. Le fonctionnement du système en l'absence
des panneaux risque d'endommager ses pièces. Pour installer les
panneaux, procédez comme suit:
1. Assurez-vous de ne pas avoir oublié d'outils ou de pièces
démontées dans le système.
2. Assurez-vous que les câbles, les cartes d'extension et les
autres composants sont bien installés.
3. Revissez solidement les panneaux du boîtier avec les vis
retirées plus tôt.
4. Remettez le cadenas en place et verrouillez-le afin de
prévenir tout accès non autorisé à l'intérieur du système.
5. Rebranchez tous les cordons d'alimentation c. a. et câbles
externes au système.
Le microprocesseur et le dissipateur de chaleur peuvent être chauds
si le système a été sous tension. Faites également attention aux
broches aiguës des cartes et aux bords tranchants du capot. Nous
vous recommandons l'usage de gants de protection.
Danger d'explosion si la batterie n'est pas remontée correctement.
Remplacer uniquement avec une batterie du même type ou d'un
type équivalent recommandé par le fabricant. Disposez des piles
usées selon les instructions du fabricant.
Le système a été conçu pour fonctionner dans un cadre de travail
normal. L'emplacement choisi doit être:
•
•
•
•
•
•
•
Intel® Server Chassis SC5400 User’s Guide
"Propre et dépourvu de poussière en suspension (sauf la
poussière normale).
"Bien aéré et loin des sources de chaleur, y compris du soleil
direct.
"A l'abri des chocs et des sources de vibrations.
"Isolé de forts champs électromagnétiques géenérés par des
appareils électriques.
"Dans les régions sujettes aux orages magnétiques il est
recomandé de brancher votre système à un supresseur de
surtension, et de débrancher toutes les lignes de
télécommunications de votre modem durant un orage.
"Muni d'une prise murale correctement mise à la terre.
"Suffisamment spacieux pour vous permettre d'accéder aux
câbles d'alimentation (ceux-ci étant le seul moyen de mettre le
système hors tension).
123
Español
El usuario debe abstenerse de manipular los componentes de la
fuente de alimentación de este producto, cuya reparación debe
dejarse exclusivamente en manos de personal técnico
especializado. Puede que este producto disponga de más de una
fuente de alimentación
No intente modificar ni usar el cable de alimentación de corriente
alterna, si no corresponde exactamente con el tipo requerido.
El número de cables suministrados se corresponden con el número
de fuentes de alimentación de corriente alterna que tenga el
producto
Nótese que el interruptor activado/desactivado en el panel frontal no
desconecta la corriente alterna del sistema. Para desconectarla,
deberá desenchufar todos los cables de corriente alterna de la
pared o desconectar la fuente de alimentación.
INSTRUCCIONES DE SEGURIDAD: Cuando extraiga la tapa del
chasis para acceder al interior del sistema, siga las siguientes
instrucciones:
1. Apague todos los dispositivos periféricos conectados al
sistema.
2. Apague el sistema presionando el interruptor encendido/
apagado.
3. Desconecte todos los cables de alimentación CA del sistema
o de las tomas de corriente alterna.
4. Identifique y desconecte todos los cables enchufados a los
conectores E/S o a los puertos situados en la parte posterior
del sistema.
5. Cuando manipule los componentes, es importante protegerse
contra la descarga electrostática (ESD). Puede hacerlo si
utiliza una muñequera antiestática sujetada a la toma de tierra
del chasis - o a cualquier tipo de superficie de metal sin pintar.
6. No ponga en marcha el sistema si se han extraído las tapas
del chasis.
Después de completar las seis instrucciones de SEGURIDAD
mencionadas, ya puede extraer las tapas del sistema. Para ello:
1. Desbloquee y extraiga el bloqueo de seguridad de la parte
posterior del sistema, si se ha instalado uno.
2. Extraiga y guarde todos los tornillos de las tapas.Extraiga las
tapas.
124
Intel® Server Chassis SC5400 User’s Guide
Para obtener un enfriamiento y un flujo de aire adecuados, reinstale
siempre las tapas del chasis antes de poner en marcha el sistema.
Si pone en funcionamiento el sistema sin las tapas bien colocadas
puede dañar los componentes del sistema. Para instalar las tapas:
1. Asegúrese primero de no haber dejado herramientas o
componentes sueltos dentro del sistema.
2. Compruebe que los cables, las placas adicionales y otros
componentes se hayan instalado correctamente.
3. Incorpore las tapas al chasis mediante los tornillos extraídos
anteriormente, tensándolos firmemente.
4. Inserte el bloqueo de seguridad en el sistema y bloquéelo
para impedir que pueda accederse al mismo sin autorización.
5. Conecte todos los cables externos y los cables de
alimentación CA al sistema.
Si el sistema ha estado en funcionamiento, el microprocesador y el
disipador de calor pueden estar aún calientes. También conviene
tener en cuenta que en el chasis o en el tablero puede haber piezas
cortantes o punzantes. Por ello, se recomienda precaución y el uso
de guantes protectores.
Existe peligro de explosión si la pila no se cambia de forma
adecuada. Utilice solamente pilas iguales o del mismo tipo que las
recomendadas por el fabricante del equipo. Para deshacerse de las
pilas usadas, siga igualmente las instrucciones del fabricante.
El sistema está diseñado para funcionar en un entorno de trabajo
normal. Escoja un lugar:
•
•
•
•
•
•
•
Intel® Server Chassis SC5400 User’s Guide
"Limpio y libre de partículas en suspensión (salvo el polvo
normal).
"Bien ventilado y alejado de fuentes de calor, incluida la luz
solar directa.
"Alejado de fuentes de vibración.
"Aislado de campos electromagnéticos fuertes producidos por
dispositivos eléctricos.
"En regiones con frecuentes tormentas eléctricas, se
recomienda conectar su sistema a un eliminador de
sobrevoltage y desconectar el módem de las líneas de
telecomunicación durante las tormentas.
"Provisto de una toma de tierra correctamente instalada.
"Provisto de espacio suficiente como para acceder a los cables
de alimentación, ya que éstos hacen de medio principal de
desconexión del sistema.
125
Italiano
Rivolgersi ad un tecnico specializzato per la riparazione dei
componenti dell'alimentazione di questo prodotto. È possibile che il
prodotto disponga di più fonti di alimentazione.
Non modificare o utilizzare il cavo di alimentazione in c.a. fornito dal
produttore, se non corrisponde esattamente al tipo richiesto. Ad ogni
fonte di alimentazione corrisponde un cavo di alimentazione in c.a.
separato
L'interruttore attivato/disattivato nel pannello anteriore non
interrompe l'alimentazione in c.a. del sistema. Per interromperla, è
necessario scollegare tutti i cavi di alimentazione in c.a. dalle prese
a muro o dall'alimentazione di corrente.
PASSI DI SICUREZZA: Qualora si rimuovano le coperture del telaio
per accedere all'interno del sistema, seguire i seguenti passi:
1. Spegnere tutti i dispositivi periferici collegati al sistema.
2. Spegnere il sistema, usando il pulsante spento/acceso
dell'interruttore del sistema.
3. Togliere tutte le spine dei cavi del sistema dalle prese
elettriche.
4. Identificare e sconnettere tutti i cavi attaccati ai collegamenti I/
O od alle prese installate sul retro del sistema.
5. Qualora si tocchino i componenti, proteggersi dallo scarico
elettrostatico (SES), portando un cinghia anti-statica da polso
che è attaccata alla presa a terra del telaio del sistema qualsiasi superficie non dipinta - .
6. Non far operare il sistema quando il telaio è senza le
coperture.
Dopo aver seguito i sei passi di SICUREZZA sopracitati, togliere le
coperture del telaio del sistema come seque:
1. Aprire e rimuovere il lucchetto dal retro del sistema qualora ve
ne fosse uno installato.
2. Togliere e mettere in un posto sicuro tutte le viti delle
coperture.
3. Togliere le coperture.
126
Intel® Server Chassis SC5400 User’s Guide
Per il giusto flusso dell'aria e raffreddamento del sistema, rimettere
sempre le coperture del telaio prima di riaccendere il sistema.
Operare il sistema senza le coperture al loro proprio posto potrebbe
danneggiare i componenti del sistema. Per rimettere le coperture del
telaio:
1. Controllare prima che non si siano lasciati degli attrezzi o dei
componenti dentro il sistema.
2. Controllare che i cavi, dei supporti aggiuntivi ed altri
componenti siano stati installati appropriatamente.
3. Attaccare le coperture al telaio con le viti tolte in precedenza e
avvitarle strettamente.
4. Inserire e chiudere a chiave il lucchetto sul retro del sistema
per impedire l'accesso non autorizzato al sistema.
5. Ricollegare tutti i cavi esterni e le prolunghe AC del sistema.
Se il sistema è stato a lungo in funzione, il microprocessore e il
dissipatore di calore potrebbero essere surriscaldati. Fare
attenzione alla presenza di piedini appuntiti e parti taglienti sulle
schede e sul telaio. È consigliabile l'uso di guanti di protezione.
Esiste il pericolo di un esplosione se la pila non viene sostituita in
modo corretto. Utilizzare solo pile uguali o di tipo equivalente a
quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire
le istruzioni del produttore.
Il sistema è progettato per funzionare in un ambiente di lavoro tipo.
Scegliere una postazione che sia:
•
•
•
•
•
•
•
Intel® Server Chassis SC5400 User’s Guide
"Pulita e libera da particelle in sospensione (a parte la normale
polvere presente nell'ambiente).
"Ben ventilata e lontana da fonti di calore, compresa la luce
solare diretta.
"Al riparo da urti e lontana da fonti di vibrazione.
"Isolata dai forti campi magnetici prodotti da dispositivi elettrici.
"In aree soggette a temporali, è consigliabile collegare il
sistema ad un limitatore di corrente. In caso di temporali,
scollegare le linee di comunicazione dal modem.
"Dotata di una presa a muro correttamente installata.
"Dotata di spazio sufficiente ad accedere ai cavi di
alimentazione, i quali rappresentano il mezzo principale di
scollegamento del sistema.
127
128
Intel® Server Chassis SC5400 User’s Guide
Appendix D: Safety Information
English
Server Safety Information
This document applies to Intel® server boards, Intel® server chassis (pedestal and rackmount) and installed peripherals. To reduce the risk of bodily injury, electrical shock, fire,
and equipment damage, read this document and observe all warnings and precautions in
this guide before installing or maintaining your Intel® server product.
In the event of a conflict between the information in this document and information
provided with the product or on the website for a particular product, the product
documentation takes precedence.
Your server should be integrated and serviced only by technically qualified persons.
You must adhere to the guidelines in this guide and the assembly instructions in your
server manuals to ensure and maintain compliance with existing product certifications and
approvals. Use only the described, regulated components specified in this guide. Use of
other products / components will void the UL Listing and other regulatory approvals of
the product, and may result in noncompliance with product regulations in the region(s) in
which the product is sold.
Safety Warnings and Cautions
To avoid personal injury or property damage, before you begin installing the product,
read, observe, and adhere to all of the following safety instructions and information. The
following safety symbols may be used throughout the documentation and may be marked
on the product and / or the product packaging.
CAUTION
Indicates the presence of a hazard that may cause minor personal injury or
property damage if the CAUTION is ignored.
WARNING
Indicates the presence of a hazard that may result in serious personal injury if
the WARNING is ignored.
Indicates potential hazard if indicated information is ignored.
Indicates shock hazards that result in serious injury or death if safety
instructions are not followed.
Intel® Server Chassis SC5400 User’s Guide
87
Indicates hot components or surfaces.
Indicates do not touch fan blades, may result in injury.
Indicates to unplug all AC power cord(s) to disconnect AC power
Please recycle battery
Intended Application Uses
This product was evaluated as Information Technology Equipment (ITE), which may be
installed in offices, schools, computer rooms, and similar commercial type locations. The
suitability of this product for other product categories and environments (such as medical,
industrial, residential, alarm systems, and test equipment), other than an ITE application,
may require further evaluation.
Site Selection
The system is designed to operate in a typical office environment. Choose a site that is:
• Clean, dry, and free of airborne particles (other than normal room dust).
• Well-ventilated and away from sources of heat including direct sunlight and
radiators.
• Away from sources of vibration or physical shock.
• Isolated from strong electromagnetic fields produced by electrical devices.
• In regions that are susceptible to electrical storms, we recommend you plug your
system into a surge suppressor and disconnect telecommunication lines to your
modem during an electrical storm.
• Provided with a properly grounded wall outlet.
• Provided with sufficient space to access the power supply cord(s), because they
serve as the product's main power disconnect.
Equipment Handling Practices
Reduce the risk of personal injury or equipment damage:
• Conform to local occupational health and safety requirements when moving and
lifting equipment.
• Use mechanical assistance or other suitable assistance when moving and lifting
equipment.
88
Intel® Server Chassis SC5400 User’s Guide
• To reduce the weight for easier handling, remove any easily detachable components.
Power and Electrical Warnings
Caution: The power button, indicated by the stand-by power marking, DOES NOT completely turn
off the system AC power, 5V standby power is active whenever the system is plugged in. To
remove power from system, you must unplug the AC power cord from the wall outlet. Your
system may use more than one AC power cord. Make sure all AC power cords are
unplugged. Make sure the AC power cord(s) is/are unplugged before you open the chassis,
or add or remove any non hot-plug components.
Do not attempt to modify or use an AC power cord if it is not the exact type required. A
separate AC cord is required for each system power supply.
Some power supplies in Intel® servers use Neutral Pole Fusing. To avoid risk of shock use
caution when working with power supplies that use Neutral Pole Fusing.
The power supply in this product contains no user-serviceable parts. Do not open the
power supply. Hazardous voltage, current and energy levels are present inside the power
supply. Return to manufacturer for servicing.
When replacing a hot-plug power supply, unplug the power cord to the power supply
being replaced before removing it from the server.
To avoid risk of electric shock, turn off the server and disconnect the power cord,
telecommunications systems, networks, and modems attached to the server before opening
it.
Power Cord Warnings
If an AC power cord was not provided with your product, purchase one that is approved
for use in your country.
Caution: To avoid electrical shock or fire, check the power cord(s) that will be used with the
product as follows:
• Do not attempt to modify or use the AC power cord(s) if they are not the exact type
required to fit into the grounded electrical outlets
• The power cord(s) must meet the following criteria:
• The power cord must have an electrical rating that is greater than that of the
electrical current rating marked on the product.
• The power cord must have safety ground pin or contact that is suitable for the
electrical outlet.
• The power supply cord(s) is/are the main disconnect device to AC power. The socket
outlet(s) must be near the equipment and readily accessible for disconnection.
• The power supply cord(s) must be plugged into socket-outlet(s) that is /are provided
with a suitable earth ground.
Intel® Server Chassis SC5400 User’s Guide
89
System Access Warnings
Caution: To avoid personal injury or property damage, the following safety instructions apply
whenever accessing the inside of the product:
• Turn off all peripheral devices connected to this product.
• Turn off the system by pressing the power button to off.
• Disconnect the AC power by unplugging all AC power cords from the system or wall
outlet.
• Disconnect all cables and telecommunication lines that are connected to the system.
• Retain all screws or other fasteners when removing access cover(s). Upon
completion of accessing inside the product, refasten access cover with original
screws or fasteners.
• Do not access the inside of the power supply. There are no serviceable parts in the
power supply. Return to manufacturer for servicing.
• Power down the server and disconnect all power cords before adding or replacing
any non hot-plug component.
• When replacing a hot-plug power supply, unplug the power cord to the power supply
being replaced before removing the power supply from the server.
Caution: If the server has been running, any installed processor(s) and heat sink(s) may be hot.
Unless you are adding or removing a hot-plug component, allow the system to cool before
opening the covers. To avoid the possibility of coming into contact with hot component(s)
during a hot-plug installation, be careful when removing or installing the hot-plug
component(s).
Caution: To avoid injury do not contact moving fan blades. If your system is supplied with a guard
over the fan, do not operate the system without the fan guard in place.
Rack Mount Warnings
The equipment rack must be anchored to an unmovable support to prevent it from tipping
when a server or piece of equipment is extended from it. The equipment rack must be
installed according to the rack manufacturer's instructions.
Install equipment in the rack from the bottom up, with the heaviest equipment at the
bottom of the rack.
Extend only one piece of equipment from the rack at a time.
You are responsible for installing a main power disconnect for the entire rack unit. This
main disconnect must be readily accessible, and it must be labeled as controlling power to
the entire unit, not just to the server(s).
To avoid risk of potential electric shock, a proper safety ground must be implemented for
the rack and each piece of equipment installed in it.
90
Intel® Server Chassis SC5400 User’s Guide
Electrostatic Discharge (ESD)
Caution: ESD can damage disk drives, boards, and other parts. We recommend that you perform all
procedures at an ESD workstation. If one is not available, provide some ESD protection
by wearing an antistatic wrist strap attached to chassis ground -- any unpainted metal
surface -- on your server when handling parts.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only
by their edges. After removing a board from its protective wrapper or from the server,
place the board component side up on a grounded, static free surface. Use a conductive
foam pad if available but not the board wrapper. Do not slide board over any surface.
Other Hazards
Battery Replacement
Caution: There is the danger of explosion if the battery is incorrectly replaced. When replacing the
battery, use only the battery recommended by the equipment manufacturer.
Dispose of batteries according to local ordinances and regulations.
Do not attempt to recharge a battery.
Do not attempt to disassemble, puncture, or otherwise damage a battery.
Intel® Server Chassis SC5400 User’s Guide
91
Cooling and Airflow
Caution: Carefully route cables as directed to minimize airflow blockage and cooling problems.
For proper cooling and airflow, operate the system only with the chassis covers installed.
Operating the system without the covers in place can damage system parts. To install the
covers:
• Check first to make sure you have not left loose tools or parts inside the system.
• Check that cables, add-in boards, and other components are properly installed.
• Attach the covers to the chassis according to the product instructions.
Laser Peripherals or Devices
Caution: To avoid risk of radiation exposure and/or personal injury:
• Do not open the enclosure of any laser peripheral or device
• Laser peripherals or devices have are not user serviceable
• Return to manufacturer for servicing
92
Intel® Server Chassis SC5400 User’s Guide
Deutsch
Sicherheitshinweise für den Server
Das vorliegende Dokument bezieht sich auf Intel® Serverplatinen, Intel® Servergehäuse
(Standfuß und Rack) sowie installierte Peripheriegeräte. Es enthält Warnungen und
Vorsichtsmaßnahmen zur Vermeidung von Gefahren durch Verletzung, Stromschlag,
Feuer und Beschädigungen von Geräten. Lesen Sie diese Dokument daher sorgfältig,
bevor Sie Ihr Intel® Serverprodukt installieren oder warten.
Bei Widersprüchen zwischen den hier vorliegenden Angaben und den Informationen im
Lieferumfang des Produkts oder auf der Website des betreffenden Produkts hat die
Produktdokumentation Vorrang.
Die Integration und Wartung des Servers darf nur durch technisch qualifizierte Personen
erfolgen.
Um die Einhaltung der vorhandenen Zulassungen und Genehmigungen für das Produkt zu
gewährleisten, sind die Richtlinien in diesem Handbuch sowie die Montageanleitungen in
den Serverhandbüchern zu beachten. Verwenden Sie nur die beschriebenen, zugelassenen
Komponenten, die im vorliegenden Handbuch angegeben werden. Die Verwendung
anderer Produkte oder Komponenten führt zum Erlöschen der UL-Zulassung und anderer
Genehmigungen für das Produkt. Dadurch kann das Produkt gegen Produktbestimmungen
verstoßen, die im Verkaufsland gelten.
Sicherheitshinweise und Vorsichtsmaßnahmen
Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor dem Beginn der
Produktinstallation die nachfolgend aufgeführten Sicherheitshinweise und -informationen
sorgfältig lesen und befolgen. In dem vorliegenden Handbuch sowie auf dem Produkt und
auf der Verpackung werden folgende Sicherheitssymbole verwendet:
VORSICHT
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung des
VORSICHTSHINWEISES zu leichteren Verletzungen bzw.
Sachbeschädigungen führen kann.
WARNUNG
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung der WARNUNG zu
ernsten Verletzungen führen kann.
Weist auf potentielle Gefahr bei Nichtbeachtung der angezeigten Informationen
hin.
Weist auf die Gefahr eines Stromschlags hin, der bei Nichtbeachtung der
Sicherheitshinweise zu schweren oder tödlichen Verletzungen führen kann.
Weist auf Verbrennungsgefahr an heißen Bauteilen bzw. Oberflächen hin.
Intel® Server Chassis SC5400 User’s Guide
93
Weist darauf hin, daß das Anfassen des Gebläses zu Verletzungen führen kann.
Bedeutet, alle Netzkabel abzuziehen und das Gerät von der Netzspannung zu
trennen.
Bereiten Sie bitte Batterie auf
Zielbenutzer der Anwendung
Dieses Produkt wurde in seiner Eigenschaft als IT-Gerät getestet, das in Büros, Schulen,
Computerräumen und ähnlichen öffentlichen Räumlichkeiten installiert werden kann. Die
Eignung dieses Produkts für andere Einsatzbereiche als IT (z. B. Medizin, Industrie,
Alarmsysteme oder Prüfgeräte) kann u. U. weitere Tests erfordern.
Standortauswahl
Das System ist für den Betrieb innerhalb normaler Büroumgebungen geeignet. Wählen
Sie einen Standort, der folgenden Kriterien entspricht:
• Sauber, trocken und frei von Partikeln in der Luft (außer dem normalen Raumstaub).
• Gut belüftet, nicht in der Nähe von Wärmequellen und keiner direkten
Sonnenbestrahlung ausgesetzt.
• Nicht in der Nähe von Vibrations oder Erschütterungsquellen.
• Abgeschirmt von starken elektromagnetischen Feldern, die durch elektrische Geräte
erzeugt werden.
• In gewittergefährdeten Gebieten sollten Sie das System an einen
Überspannungsschutz anschließen und bei einem Gewitter die
Telekommunikationskabel zum Modem abziehen.
• Eine ordnungsgemäß geerdete Wandsteckdose muß vorhanden sein.
• Ausreichender Freiraum für den Zugang zu den Netzkabeln, da diese die
Hauptvorrichtung zum Trennen des Produkts von der Stromversorgung sind.
Handhabung von Geräten
Beachten Sie zur Vermeidung von Verletzungen oder Beschädigungen an den Geräten die
folgenden Hinweise:
• Halten Sie beim Transportieren und Anheben von Geräten die örtlichen Gesundheits
und Sicherheitsvorschriften ein.
• Verwenden Sie mechanische oder andere geeignete Hilfsmittel zum Transportieren
oder Anheben von Geräten.
94
Intel® Server Chassis SC5400 User’s Guide
• Entfernen Sie alle Komponenten, die sich leicht abnehmen lassen, um das Gewicht
zu reduzieren und die Handhabung zu erleichtern.
Warnungen zu Netzspannung und Elektrizität
Vorsicht: Durch Betätigen der mit dem Standby-Symbol gekennzeichneten Netztaste wird das
System NICHT vollständig vom Netz getrennt. Es sind weiterhin 5 V aktiv, solange das
System eingesteckt ist. Um das System vollständig vom Strom zu trennen, muß das
Netzkabel aus der Steckdose abgezogen werden. Das System verfügt möglicherweise über
mehrere Netzkabel. Vergewissern Sie sich in diesem Fall, daß alle Netzkabel abgezogen
sind. Wenn Sie Komponenten ein- oder ausbauen möchten, die nicht hot-plug-fähig sind,
stellen Sie sicher, daß zuvor alle Netzkabel abgezogen sind.
Nehmen Sie keine Änderungen am Netzkabel vor, und verwenden Sie kein Kabel, das nicht
genau dem geforderten Typ entspricht. Jedes Netzteil im System muß über ein eigenes
Netzkabel angeschlossen werden.
Einige Netzteile von Intel Servern verwenden Nullleitersicherungen. Vorsicht ist geboten
im Umgang mit Netzteilen, welche Nullleitersicherungen verwenden, um das Risiko eines
elektrischen Schlages zu vermeiden
Das Netzteil in diesem Produkt enthält keine Teile, die vom Benutzer gewartet werden
können. Öffnen Sie das Netzteil nicht. Im Netzteil bestehen gefährliche Spannungen,
Ströme und Energiequellen. Schicken Sie das Gerät für Wartungsarbeiten an den
Hersteller zurück.
Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab, bevor
Sie es aus dem Server ausbauen.
Zur Vermeidung von Stromschlägen schalten Sie den Server aus, und trennen Sie vor dem
Öffnen des Geräts das Netzkabel sowie alle an den Server angeschlossene
Telekommunikationssysteme, Netzwerke und Modems.
Intel® Server Chassis SC5400 User’s Guide
95
Hinweis für Netzkabel
Wenn kein Netzkabel mit dem Produkt geliefert wurde, kaufen Sie ein Kabel, das für die
Vorsicht: Prüfen Sie zur Vermeidung von Stromschlag- oder Feuergefahr die mit dem Produkt zu
verwendenden Netzkabel wie folgt:
• Nehmen Sie keine Änderungen an einem Netzkabel vor, und benutzen sie es nicht,
wenn es nicht genau in die geerdeten Netzsteckdosen paßt.
• Netzkabel müssen die folgenden Anforderungen erfüllen:
• Die Nennbelastbarkeit des Netzkabels muß mindestens so hoch sein wie die am
Produkt angegebenen Nennstromaufnahme.
• Das Netzkabel muß einen zur Netzsteckdose passenden Schutzkontakt besitzen.
• Die Netzkabel sind die Hauptvorrichtung zum Trennen des Geräts vom Stromnetz.
Die Steckdose muß in der Nähe der Anlage angebracht und gut erreichbar sein.
• Netzkabel müssen an eine ordnungsgemäß geerdete Steckdose angeschlossen sein.
Warnhinweise für den Systemzugang
Vorsicht: Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor Arbeiten im
Produktinneren folgende Sicherheitsanweisungen beachten:
• Schalten Sie alle am Produkt angeschlossenen Peripheriegeräte aus.
• Schalten Sie das System mit dem Netzschalter aus.
• Trennen Sie das Gerät von der Stromquelle, indem Sie alle Netzkabel vom System
bzw. aus der Steckdose ziehen.
• Ziehen Sie alle Kabel und alle an das System angeschlossenen
Telekommunikationsleitungen ab.
• Bewahren Sie alle Schrauben und anderen Befestigungselemente gut auf, nachdem
Sie die Gehäuseabdeckung entfernt haben. Wenn Sie Ihre Arbeiten im Systeminneren
beendet haben, befestigen Sie die Gehäuseabdeckung mit den Originalschrauben
bzw. -befestigungselementen.
• Führen Sie keine Arbeiten im Netzteil aus.Das Netzteil enthält keine für den
Benutzer wartungsbedürftigen Teile. Schicken Sie das Gerät für Wartungsarbeiten
an den Hersteller zurück.
• Schalten Sie den Server aus, und ziehen Sie alle Netzkabel ab, bevor Sie
Komponenten ein- oder ausbauen, die nicht hot-plug-fähig sind.
• Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab,
bevor Sie es aus dem Server ausbauen.
Vorsicht: War Ihr Server in Betrieb, können die installierten Prozessoren und Kühlkörper heiß sein.
Sofern Sie keine Hot-Plug-Komponenten ein- oder ausbauen, warten Sie mit dem
Abnehmen der Abdeckungen, bis das System abgekühlt ist. Gehen Sie beim Aus- oder
96
Intel® Server Chassis SC5400 User’s Guide
Einbauen von Hot-Plug-Komponenten sorgfältig vor, um nicht mit heißen Komponenten
in Berührung zu kommen.
Vorsicht: Berühren Sie nicht die rotierenden Lüfterflügel, um Verletzungen zu vermeiden. Falls Ihr
System mit eine Lüfterabdeckung besitzt, darf es nicht ohne diese Abdeckung betrieben
werden.
Warnhinweise für Racks
Das Geräte-Rack muß auf einer geeigneten, festen Unterlage verankert werden, um ein
Umkippen zu vermeiden, wenn ein Server oder andere Geräte herausgezogen werden. Bei
der Installation des Racks müssen die Anweisungen des Rack-Herstellers beachtet
werden.
Gehen Sie bei der Installation von Geräten im Rack immer von unten nach oben vor, und
bauen Sie das schwerste Gerät an der untersten Position im Rack ein.
Ziehen Sie jeweils immer nur ein Gerät aus dem Rack heraus.
Sie müssen für die gesamte Rack-Einheit einen Netztrennschalter einrichten. Dieser
Netztrennschalter muß leicht zugänglich sein und über eine Kennzeichnung verfügen, die
besagt, daß er die Stromzufuhr zur gesamten Einheit steuert und nicht nur zu den Servern.
Zur Vermeidung von Stromschlaggefahr müssen das Rack selbst und alle darin
eingebauten Geräte ordnungsgemäß geerdet sein.
Elektrostatische Entladungen (ESD)
Vorsicht: Elektrostatische Entladungen können zur Beschädigung von Festplatten, Platinen und
anderen Komponenten führen. Daher sollten Sie alle Arbeiten an einer ESD-Workstation
ausführen. Steht ein solcher Arbeitsplatz nicht zur Verfügung, erzielen Sie einen gewissen
Schutz vor elektrostatischen Entladungen durch Tragen einer Antistatik-Manschette, die
Sie während der Arbeit zur Erdung an einem beliebigen unlackierten Metallteil des
Computergehäuses befestigen.
Gehen Sei bei der Handhabung von Platinen immer mit größter Vorsicht vor. Sie können
äußerst empfindlich gegenüber elektrostatischer Entladung sein. Halten Sie Platinen nur
an den Kanten fest. Legen Sie die Platinen nach dem Auspacken aus der Schutzhülle oder
nach dem Ausbau aus dem Server mit der Bauelementseite nach oben auf eine geerdete,
statisch entladene Unterlage.Verwenden Sie dazu, sofern verfügbar, eine leitfahige
Schaumstoffunterlage, aber niche die Schutzhülle der Platine. Ziehen Sie die Platine nicht
über eine Fläche.
Intel® Server Chassis SC5400 User’s Guide
97
Andere Gefahren
Batterieaustausch
Vorsicht: Wird die Batterie unsachgemäß ausgetauscht, besteht Explosionsgefahr. Verwenden Sie
als Ersatz nur die vom Gerätehersteller empfohlene Batterie.
Beachten Sie bei der Entsorgung von Batterien die gültigen Bestimmungen.
Versuchen Sie nicht, eine Batterie aufzuladen.
Versuchen Sie nicht, eine Batterie zu öffnen oder sonstwie zu beschädigen.
Kühlung und Luftstrom
Vorsicht: Verlegen Sie Kabel sorgfältig entsprechend der Anleitung, um Störungen des Luftstroms
und Kühlungsprobleme zu vermeiden.
Zur Gewährleistung des ordnungsgemäßen Kühlungs- und Luftstromverhaltens darf das
System nur mit angebrachten Gehäuseabdeckungen betrieben werden. Die
Inbetriebnahme des Systems ohne Abdeckung kann zur Beschädigung von
Systemkomponenten führen. So bringen Sie die Abdeckung wieder an:
• Vergewissern Sie sich zunächst, daß Sie keine Werkzeuge oder Teile im Gehäuse
vergessen haben.
• Prüfen Sie, ob Kabel, Erweiterungskarten sowie weitere Komponenten
ordnungsgemäß angebracht sind.
• Befestigen Sie die Abdeckungen am Gehäuse des Produkts, wie in dessen Anleitung
beschrieben.
Laser-Peripheriegeräte oder -Komponenten
Vorsicht: Beachten Sie zur Vermeidung von Strahlung und Verletzungen die folgenden Hinweise:
• Öffnen Sie keinesfalls das Gehäuse von Laser-Peripheriegeräten oder LaserKomponenten.
• Laser-Peripheriegeräte oder -Komponenten besitzen keine für den Benutzer
wartungsbedürftigen Teile.
• Schicken Sie das Gerät für Wartungsarbeiten an den Hersteller zurück.
98
Intel® Server Chassis SC5400 User’s Guide
Français
Consignes de sécurité sur le serveur
Ce document s’applique aux cartes serveur Intel®, au châssis de serveur Intel® (sur pieds
et sur rack) et aux périphériques installés. Pour réduire les risques de dommages
corporels, d’électrocution, d’incendie et de dommages matériels, lisez ce document et
respectez tous les avertissements et précautions mentionnés dans ce guide avant
d’installer ou de mettre à jour votre produit serveur Intel®.
En cas de conflit entre les informations fournies dans ce document et celles livrées avec le
produit ou publiées sur le site Web pour un produit particulier, la documentation du
produit prime.
Votre serveur doit être intégré et entretenu uniquement par des techniciens qualifiés.
Vous devez suivre les informations de ce guide et les instructions d’assemblage des
manuels de serveur pour vérifier et maintenir la conformité avec les certifications et
approbations de produit existantes. Utilisez uniquement les composants décrits et
réglementés spécifiés dans ce guide. L’utilisation d’autres produits/composants annulera
la liste UL et les autres approbations réglementaires du produit, et le produit peut ne pas
être conforme aux autres lois et réglementations locales applicables au produit.
Sécurité: avertissements et mises en garde
Pour éviter de vous blesser ou d’endommager votre équipement, lisez et respectez toutes
les informations et consignes de sécurité avant de commencer l’installation du produit.
Les symboles de sécurité suivants peuvent être utilisés tout au long de cette
documentation et peuvent figurer sur le produit ou sur son emballage.
ATTENTION
Indique la présence d’un risque pouvant entraîner des blessures physiques
mineures ou endommager légèrement le matériel si la mise en garde n’est pas
prise en compte.
AVERTISSEMENT
Indique la présence d’un risque pouvant entraîner des blessures corporelles
graves si l’avertissement n’est pas pris en compte.
Indique un risque potentiel si les informations signalées ne sont pas prises en
compte.
Indique des risques d’électrocution pouvant entraîner des blessures
corporelles graves ou mortelles si les consignes de sécurité ne sont pas
respectées.
Signale des composants ou des surfaces soumis à des températures élevées.
Indique de ne pas toucher aux pales de ventilateur, car cela peut entraîner des
blessures.
Intel® Server Chassis SC5400 User’s Guide
99
Indique de débrancher tous les cordons d’alimentation secteur pour
déconnecter l’alimentation.
Veuillez réutiliser la batterie
Domaines d’utilisation prévus
Ce produit a été testé comme équipement informatique (ITE) et peut être installé dans des
bureaux, des écoles, des salles informatiques et des endroits commerciaux similaires.
L’utilisation du présent produit dans des catégories et environnements de produits et
domaines d’application (par exemple, le domaine médical, industriel, résidentiel, les
systèmes d’alarme et les appareils de contrôle) autres qu’ITE doit faire l’objet
d’évaluations supplémentaires.
Sélection d’un emplacement
Le système est conçu pour fonctionner dans un environnement standard de bureau.
Choisissez un emplacement respectant les conditions suivantes :
• Propre, sec et exempt de particules en suspension (autres que la poussière normale
d’une pièce).
• Bien ventilé et à l’écart des sources de chaleur telles que la lumière directe du soleil
et les radiateurs.
• À l’écart des sources de vibration ou des chocs physiques.
• Isolé des champs électromagnétiques importants produits par des appareils
électriques.
• Dans les régions sujettes aux orages magnétiques, nous vous recommandons de
brancher votre système à un suppresseur de surtension et de déconnecter les lignes
de télécommunication de votre modem pendant les orages.
• Équipé d’une prise murale reliée à la terre.
• Équipé d’un espace suffisant pour accéder aux cordons d’alimentation secteur, car ils
servent de disjoncteur principal d’alimentation du produit.
Pratiques de manipulation de l’équipement
Réduisez le risque de dommages personnels ou matériels :
• Conformez-vous aux exigences de médecine du travail et de sécurité lorsque vous
déplacez et soulevez le matériel.
• Utilisez l’assistance mécanique ou toute autre assistance appropriée lorsque vous
déplacez et soulevez le matériel.
• Pour réduire le poids en vue de faciliter la manipulation, retirez tout composant
amovible.
100
Intel® Server Chassis SC5400 User’s Guide
Alimentation et avertissements en matière d’électricité
Attention: Le bouton d’alimentation, indiqué par le symbole de mise en veille, NE COUPE PAS
complètement l’alimentation secteur du système car le courant de veille 5 V reste actif
lorsque le système est sous tension. Pour couper l’alimentation du système, vous devez
débrancher le cordon d’alimentation secteur de la prise murale. Votre système peut
utiliser plusieurs cordons d’alimentation secteur. Assurez-vous que tous les cordons
d’alimentation sont débranchés. Vous devez les débrancher avant d’ouvrir le châssis,
d’ajouter ou de supprimer un composant non connectable à chaud.
Les alimentations de certains serveurs Intel sont munies de doubles fusibles pôle/neutre:
veuillez observer les précautions d'usage afin d'éviter tout risque d'eléctrocution.
N’essayez pas de modifier ou d’utiliser un cordon d’alimentation secteur s’il ne s’agit pas
du type exact requis. Un cordon secteur est requis pour chaque alimentation système.
Le bloc d’alimentation de ce produit ne contient aucun composant réparable par
l’utilisateur. N’ouvrez pas le bloc d’alimentation. L’intérieur de celui-ci est soumis à des
niveaux dangereux de tension, de courant et d’énergie. Renvoyez-le au fabricant en cas de
problème.
Lorsque vous remplacez un bloc d’alimentation à chaud, débranchez le cordon du bloc
d’alimentation en cours de remplacement avant de le retirer du serveur.
Pour éviter tout risque d’électrocution, mettez le système hors tension et débranchez les
cordons d’alimentation ainsi que les systèmes de télécommunication, réseaux et modems
reliés au système avant d’ouvrir ce dernier.
Avertissements sur le cordon d’alimentation
Si aucun cordon d’alimentation secteur n’a été fourni avec votre produit, vous devez vous
en procurer un qui soit approuvé pour une utilisation dans votre pays.
Attention: Pour éviter tout risque d’électrocution ou d’incendie, vérifiez les cordons d’alimentation
qui seront utilisés avec le produit comme suit:
• N’essayez pas d’utiliser ou de modifier les cordons d’alimentation en CA s’ils ne
correspondent pas exactement au type requis pour les prises électriques reliées à la
terre.
• Les cordons d’alimentation doivent répondre aux critères suivants :
• Le cordon d’alimentation doit supporter une intensité supérieure à celle indiquée
sur le produit.
• Le cordon d’alimentation doit posséder une broche ou un contact de mise à la terre
approprié à la prise électrique.
• Les cordons d’alimentation électrique représentent le principal dispositif de
déconnexion raccordé à l’alimentation secteur. Les prises de courant doivent se
trouver à proximité de l’équipement et être facilement accessibles pour une
déconnexion.
• Les cordons d’alimentation doivent être branchés sur des prises électriques
correctement reliées à la terre.
Intel® Server Chassis SC5400 User’s Guide
101
Avertissements sur l’accès au système
Attention: Pour éviter de vous blesser ou d’endommager votre équipement, les consignes de sécurité
suivantes s’appliquent chaque fois que vous accédez à l’intérieur du produit:
• Mettez hors tension tous les périphériques connectés à ce produit.
• Éteignez le système en appuyant sur le bouton d’alimentation.
• Déconnectez l’alimentation secteur en débranchant tous les cordons d’alimentation
secteur du système ou de la prise murale.
• Déconnectez l’ensemble des câbles et lignes de télécommunication qui sont
connectés au système.
• Mettez toutes les vis ou autres attaches de côté lorsque vous retirez les panneaux
d’accès. Une fois que vous avez terminé d’accéder à l’intérieur du produit, refixez le
panneau d’accès avec les vis ou attaches d’origine.
• N’essayez pas d’accéder à l’intérieur du bloc d’alimentation. Il ne contient aucune
pièce réparable. Renvoyez-le au fabricant en cas de problème.
• Mettez le serveur hors tension et débranchez tous les cordons d’alimentation avant
d’ajouter ou de remplacer tout composant non connectable à chaud.
• Lorsque vous remplacez le bloc d’alimentation à chaud, débranchez le cordon du bloc
d’alimentation en cours de remplacement avant de retirer le bloc du serveur.
Attention: Si le serveur a été utilisé, les processeurs et dissipateurs de chaleur installés peuvent être
chauds. À moins que vous n’ajoutiez ou ne retiriez un composant connectable à chaud,
laissez le système refroidir avant d’ouvrir les panneaux. Pour éviter tout risque d’entrer
en contact avec un composant chaud lors d’une installation à chaud, prenez toutes les
précautions nécessaires lorsque vous retirez ou installez des composants connectables à
chaud.
Attention: Pour éviter de vous blesser, ne touchez pas les pales de ventilateur en mouvement. Si votre
système est fourni avec une protection sur le ventilateur, ne mettez pas le système en route
sans la protection en place.
Avertissements sur le montage en rack
Le rack doit être fixé à un support inamovible pour éviter qu’il ne bascule lors de
l’extension d’un serveur ou d’un élément de l’équipement. Le rack doit être installé
conformément aux instructions du fabricant.
Installez les équipements dans le rack en partant du bas, en plaçant le plus lourd en bas du
rack.
N’étendez qu’un seul élément de l’équipement à partir du rack à la fois.
Vous êtes responsable de l’installation d’un disjoncteur principal d’alimentation pour la
totalité du rack. Ce disjoncteur principal doit être rapidement accessible et doit être
étiqueté comme contrôlant toute l’unité, et pas uniquement le ou les serveurs.
102
Intel® Server Chassis SC5400 User’s Guide
Pour éviter tout risque d’électrocution, le rack et chaque élément de l’équipement installé
dans le rack doivent être correctement reliés à la terre.
Décharges électrostatiques (ESD)
Attention: Les décharges électrostatiques (ESD) peuvent endommager les lecteurs de disque dur, les
cartes et d’autres pièces. Il est fortement conseillé d’effectuer l’ensemble des procédures
décrites à un poste de travail protégé contre les ESD. Au cas où aucun poste de ce type ne
serait disponible, protégez-vous contre les ESD en portant un bracelet antistatique relié à
la masse du châssis (n’importe quelle surface métallique non peinte) de votre serveur
lorsque que vous manipulez les pièces.
Manipulez toujours les cartes avec précaution. Elles peuvent être extrêmement sensibles
aux ESD. Ne tenez les cartes que par leurs bords. Après avoir retiré une carte de son
emballage de protection ou du serveur, placez-la sur une surface reliée à la terre, exempte
de charge statique, composants orientés vers le haut. Utilisez si possible un tapi de
mousse conducteru, mais pas l’emballage de la carte. Veillez à ce que la carte ne glisse
sur aucune surface.
Autres risques
Remplacement de la pile
Attention: Il existe un risque d’explosion si la pile n’est pas correctement remplacée. Lors du
remplacement de la pile, utilisez uniquement celle recommandée par le fabricant du
matériel.
Mettez la pile au rebut en vous conformant aux réglementations locales.
N’essayez pas de recharger une pile.
N’essayez pas de démonter, de percer ou d’endommager la pile d’une quelconque façon.
Refroidissement et ventilation
Attention: Routez les câbles avec précaution comme indiqué pour minimiser les blocages de
circulation d’air et les problèmes de refroidissement.
Afin de permettre une ventilation et un refroidissement corrects, ne mettez le système en
marche que lorsque les panneaux du châssis sont en place. L’utilisation du système sans
les panneaux peut endommager les composants système. Pour installer les panneaux :
• Vérifiez tout d’abord que vous n’avez pas oublié d’outils ou de composants détachés
à l’intérieur du système.
• Vérifiez que les câbles, les cartes d’extension et les autres composants sont
correctement installés.
• Fixez les panneaux au châssis en suivant les instructions du produit.
Intel® Server Chassis SC5400 User’s Guide
103
Périphériques laser
Attention: Pour éviter tout risque d’exposition aux rayonnements et/ou de dommage personnel:
• N’ouvrez pas l’enceinte d’un périphérique laser.
• Les périphériques laser ne sont pas réparables par l’utilisateur.
• Retournez-les au fabricant en cas de problème.
104
Intel® Server Chassis SC5400 User’s Guide
Español
Información de seguridad del servidor
Este documento se aplica a las tarjetas de servidor de Intel®, las carcasas de servidor de
Intel® (montaje en bastidor y en pedestal) y los dispositivos periféricos. Para reducir el
riesgo de daños corporales, descargas eléctricas, fuego y en el equipo, lea este documento
y preste atención a todos las advertencias y precauciones de esta guía antes de instalar o
mantener el producto de servidor de Intel®.
En el caso de que haya diferencias entre la información para un producto en particular
contenida en este documento y la información proporcionada con dicho producto o en el
sitio Web, la documentación del producto es la que prevalece.
Sólo personal técnico cualificado debe montar y prestar los servicios para el servidor.
Debe ceñirse a las directrices de esta guía y a las instrucciones de montaje de los manuales
del servidor para asegurar y mantener el cumplimiento con las certificaciones y
homologaciones existentes de los productos. Utilice sólo los componentes descritos y
homologados que se especifican en esta guía. El uso de otros productos o componentes
anulará la homologación UL y otras certificaciones oficiales del producto, pudiendo dejar
de ser compatible con las normativas locales de los países en los que se comercializa.
Advertencias y precauciones sobre seguridad
Para reducir la posibilidad de que se produzcan lesiones personales o daños en la
propiedad, antes de empezar a instalar el producto, lea, observe y cumpla toda la
información e instrucciones de seguridad siguientes. Puede que se utilicen los siguientes
símbolos de seguridad en la documentación y es posible que aparezcan en el producto o en
su embalaje.
PRECAUCIÓN
ADVERTENCIA
Indica la existencia de un riesgo que podría causar lesiones personales o daños
en la propiedad leves si no se tiene en cuenta la PRECAUCIÓN.
Indica la existencia de un riesgo que podría causar lesiones personales graves
si no se tiene en cuenta la ADVERTENCIA.
Indica un riesgo potencial si no se tiene en cuenta la información indicada.
Indica riesgo de descargas eléctricas que podrían causar lesiones graves o la
muerte si no se siguen las instrucciones de seguridad.
Indica componentes o superficies calientes.
Indica que no se deben tocar las aspas de los ventiladores, ya que de lo
contrario se podrían producir lesiones.
Intel® Server Chassis SC5400 User’s Guide
105
Indica que es necesario desenchufar los cables de alimentación de CA para
desconectar la alimentación de CA
Recicle por favor la batería
Aplicaciones y usos previstos
Este producto ha sido evaluado como equipo de tecnología informática (ITE) que puede
instalarse en oficinas, escuelas, salas de equipos informáticos o lugares de ámbito
comercial similares. Es posible que sea necesario llevar a cabo una evaluación adicional
para comprobar si este producto es apropiado para otras categorías de productos y
entornos además de las aplicaciones informáticas (por ejemplo, soluciones médicas,
industriales, residenciales, sistemas de alarma y equipos de pruebas).
Selección de la ubicación
El sistema se ha diseñado para funcionar en un entorno normal de oficinas. Seleccione una
ubicación que esté:
• Limpia, seca y libre de macropartículas en suspensión en el aire (que no sean el
polvo habitual de la habitación).
• Bien ventilada y alejada de fuentes de calor, incluida la luz solar directa y los
radiadores.
• Alejada de fuentes de vibración o de golpes físicos.
• Aislada de campos electromagnéticos producidos por dispositivos eléctricos.
• En zonas propensas a tormentas eléctricas, se recomienda que conecte el servidor a
un supresor de sobretensiones y desconecte las líneas de telecomunicaciones al
módem durante una tormenta eléctrica.
• Provista de una toma de corriente alterna correctamente conectada a tierra.
• Provista de espacio suficiente para acceder a los cables de la fuente de alimentación
ya que constituyen la desconexión principal de la alimentación.
Manipulación del equipo
Reduzca el riesgo de daños personales o en el equipo:
• Respete los requisitos de sanidad y seguridad laborales de su país cuando traslade y
levante el equipo.
• Utilice medios mecánicos u otros que sean adecuados al trasladar o levantar el
equipo.
• Para que el peso sea menor para manipularlo con más facilidad, extraiga los
componentes que sean de fácil extracción.
106
Intel® Server Chassis SC5400 User’s Guide
Advertencias de alimentación y eléctricas
Precaución: El botón de encendido, indicado con la marca del modo de reposo o stand-by, NO
DESCONECTA completamente la alimentación de CA del sistema, ya que el modo de
reposo de 5 V sigue activo mientras el sistema está enchufado. Para desconectar el
sistema debe desenchufar el cable de alimentación de CA de la toma de la pared. Puede
usar más de un cable de alimentación de CA con el sistema. Asegúrese de que todos los
cables de alimentación de CA están desenchufados. Asegúrese de que los cables de
alimentación de CA estén desenchufado antes de abrir la carcasa, agregar o extraer
cualquier componente que no es de conexión en funcionamiento.
Algunas fuentes de alimentación de electricidad de los servidores de Intel utilizan el polo
neutral del fuselaje. Para evitar riesgos de choques electricos use precauciónes al
trabajar con las fuentes de alimentación que utilizan el polo neutral de fuselaje.
No intente modificar ni utilizar un cable de alimentación de CA si no es del tipo exacto
requerido. Se necesita un cable de CA para cada fuente de alimentación del sistema.
La fuente de alimentación de este producto no contiene piezas que puedan ser reparadas
por el usuario. No abra la fuente de alimentación. Dentro de la fuente de alimentación
puede haber niveles de tensión, corriente y energía peligrosos. Devuélvala al fabricante
para repararla.
Al reemplazar una fuente de alimentación de conexión en funcionamiento, desenchufe el
cable de alimentación de la fuente de alimentación que va a reemplazar antes de extraerla
del servidor.
Para evitar el riesgo de descargas eléctricas, antes de abrir el servidor, apáguelo,
desconecte el cable de alimentación, los sistemas de telecomunicaciones, las redes y los
módems conectados al mismo.
Advertencias sobre el cable de alimentación
Si no se ha proporcionado con el producto ningún cable de alimentación de CA, adquiera
alguno cuyo uso esté aprobado en su país.
Precaución: Para evitar descargas eléctricas o fuego, revise los cables de alimentación que usará con
el producto tal y como se describe a continuación:
• No intente modificar ni utilizar los cables de alimentación de CA si no son
exactamente del modelo especificado para ajustarse a las tomas de corriente
conectadas a tierra
• Los cables de alimentación deben reunir los siguientes requisitos:
• El cable de alimentación debe disponer de una capacidad nominal de corriente
eléctrica mayor que la capacidad especificada en el producto.
• El cable de alimentación debe disponer de una patilla o contacto de conexión a
tierra que sea apto para la toma de corriente.
• Los cables de la fuente de alimentación son los dispositivos de desconexión
principales a la corriente alterna. El enchufe o enchufes de zócalo deben
encontrarse cerca del equipo y el acceso a ellos debe poderse efectuar de forma
inmediata con el fin de desconectarlos.
Intel® Server Chassis SC5400 User’s Guide
107
• Los cables de la fuente de alimentación deben estar conectados a los enchufes con
una toma de tierra adecuada.
Advertencias el acceso al sistema
Precaución: Para evitar lesiones personales o daños en la propiedad, se aplican las siguientes
instrucciones de seguridad siempre que se acceda al interior del producto:
• Apague todos los dispositivos periféricos conectados a este producto.
• Pulse el botón de alimentación para apagar el sistema.
• Desconecte la alimentación de CA desenchufando los cables de alimentación de CA
del sistema o de la toma de corriente alterna.
• Desconecte todos los cables y líneas de telecomunicación que estén conectados al
sistema.
• Guarde todos los tornillos o elementos de fijación cuando retire las cubiertas de
acceso. Cuando termine de operar en el interior del producto, vuelva a colocar los
tornillos o los elementos de fijación originales de la cubierta de acceso.
• No acceda al interior de la fuente de alimentación. No hay elementos en la fuente de
alimentación que usted pueda reparar y utilizar. Devuélvala al fabricante para
repararla.
• Apague el servidor y desconecte todos los cables de alimentación antes de agregar
o reemplazar cualquier componente que no es de conexión en funcionamiento.
• Al reemplazar una fuente de alimentación de conexión en funcionamiento, desenchufe
el cable de alimentación de la fuente de alimentación que va a reemplazar antes de
extraerla del servidor.
Precaución: Si el servidor se ha estado ejecutando, los procesadores y disipadores de calor estarán
recalentados. A no ser que esté instalando o extrayendo un componente de conexión en
funcionamiento, deje que el sistema se enfríe antes de abrir las cubiertas. Para que no
llegue a tocar los componentes que estén calientes cuando esté realizando una instalación
de conexión en funcionamiento, tenga cuidado al extraer o instalar los componentes de
conexión en funcionamiento.
Precaución: Para evitar posibles daños, no toque las aspas en movimiento de los ventiladores. Si el
sistema se le ha suministrado con una protección para el ventilador, asegúrese de que
cuando esté funcionando el sistema la protección esté en su sitio.
Advertencias sobre el montaje en bastidor
El bastidor del equipo se debe sujetar con un soporte fijo para evitar que se caiga cuando
se extraiga un servidor o una pieza del mismo. El bastidor del equipo debe instalarse
siguiendo las instrucciones del fabricante del bastidor.
Instale el equipo en el bastidor comenzando desde la parte de abajo, con el equipo más
pesado en la parte inferior del bastidor.
108
Intel® Server Chassis SC5400 User’s Guide
Extraiga las piezas del equipo del bastidor de una a una.
El usuario es el responsable de la instalación de un dispositivo de desconexión de la
alimentación principal para toda la unidad del bastidor. El acceso a este dispositivo de
desconexión deberá ser de fácil acceso y deberán incluirse indicaciones que lo
identifiquen como el control de alimentación eléctrica de toda la unidad, no sólo de los
servidores.
Para evitar el riesgo de descargas eléctricas, deberá instalar una conexión a tierra
apropiada para el bastidor y para cada pieza del equipo instalada en el mismo.
Descarga electrostática (ESD)
Precaución: Las descargas electrostáticas pueden dañar las unidades de disco, las tarjetas y otros
componentes. Recomendamos que realice todos los procedimientos en una estación de
trabajo protegida contra descargas electrostáticas. En caso de que no haya una
disponible, protéjase de alguna forma contras las descargas llevando un brazalete
antiestático conectado a la toma de tierra de la carcasa (cualquier superficie de metal
que no esté pintada) del servidor cuando manipule las piezas.
Manipule siempre las tarjetas con el máximo cuidado. Pueden ser sumamente sensibles a
las descargas electrostáticas. Sujételas sólo por los bordes. Una vez extraída la tarjeta de
su envoltorio de protección o del servidor, colóquela con el lado de los componentes
hacia arriba sobre una superficie con toma de tiearra y sin carga estática. Utilice una
almohadilla de espuma conductora si dispone de ella, pero nunca el envoltorio de la
tarjeta. No deslice la tarjeta sobre ninguna superficie.
Sustitución de la batería
Precaución: Existe el peligro de explosión si la batería no se reemplaza correctamente. Al reemplazar
la batería, utilice sólo la batería recomendada por el fabricante del equipo.
Deseche las baterías respetando la normativa local.
No intente recargar la batería.
No intente desmontar, pinchar o causar cualquier otro desperfecto a una batería.
Enfriamiento y circulación de aire
Precaución: El tendido de los cables debe realizarse cuidadosamente tal y como se le indica para
reducir al mínimo los problemas de obstrucción de la ventilación y de refrigeración.
Para conseguir una refrigeración y corriente de aire adecuadas, compruebe que cuando
sistema esté funcionando, las cubiertas de la carcasa están instaladas. Si utiliza el sistema
sin las cubiertas, podría dañar sus componentes. Para instalar las cubiertas:
• Compruebe primero que no ha dejado herramientas o piezas sueltas dentro del
sistema.
• Compruebe que los cables, tarjetas adicionales y otros componentes están
instalados correctamente.
Intel® Server Chassis SC5400 User’s Guide
109
• Sujete las cubiertas a la carcasa siguiendo las instrucciones del producto.
Periféricos o dispositivos láser
Precaución: Para evitar el riesgo de la exposición a radiaciones o de daños personales:
• No abra la caja de ningún periférico o dispositivo láser
• Los periféricos o dispositivos láser no pueden ser reparados por el usuario
• Haga que el fabricante los repare.
110
Intel® Server Chassis SC5400 User’s Guide
简体中文
服务器安全信息
本文档适用于 Intel® 服务器主板、Intel®
服务器机箱(基座和机架固定件)和已安装的外设。为减少人身伤害、电击、火
以及设备毁坏的危险,请在安装或维护 Intel®
服务器产品之前阅读本文档并遵循本指南中的所有警告和预防措施。
如果本文档中的信息与特定产品的随附信息或 Web
站点信息之间存在不一致,请以产品文档为准。
服务器须由合格的技术人员进行集成和维护。
必须遵守本指南的规定和服务器手册的装配指导,以确保符合现有的产品认证和
批。仅使用本指南中描述和规定的指定组件。使用其他产品 / 组件将使产品的
认证和其他管理审批无效,并可能导致产品不符合销售地的产品法规。
安全警告与注意事项
为避免人身伤害与财产损失,安装本产品之前,请阅读以下所有安全指导和信息
下面所列的安全符号可能在整个文档中使用并可能标注于产品和 /
或产品包装之上。
注意
表示如果无视此“? ? ? 项”? ? ? ? ? ? ? 轻微人身伤害或财产损失的危
警告
表示如果无视此“? ? ”? ? ? ? ? ? ? 严重人身伤害的危险。
表示如果无视所示信息,即存在潜在的危险。
表示如果不遵守安全指导,存在可导致严重伤害或死亡的电击危险。
表示灼热组件或表面。
表示请勿触摸风机叶片,否则可能致伤。
表示拔下所有交流电线,断开交流电源
Intel® Server Chassis SC5400 User’s Guide
111
预期应用使用
根据评估,本产品为信息技术设备
(ITE),可安装在办公室、学校、计算机房和类似的商业场所。本产品对于非 ITE
应用的其他产品种类和环境(如医疗、工业、住宅、报警系统和测试设备)的适用
性尚有待进一步的评估。
场地选择
本系统专为在典型办公环境运行而设计。请选择符合以下条件的地点:
•
•
•
•
•
•
•
清洁、干燥,无气载微粒(而非一般的室内尘埃)。
通风良好,远离热源(包括直接日晒和散热器)。
远离振动源或物理震动。
与电气设备产生的强大电磁场隔离。
在易受闪电袭击的地区,我们建议将系统插入电涌抑制器并在闪电期间断开通信
线路与调制解调器之间的连接。
提供正确接地的墙壁插座。
提供足够的空间,以便拿取电源供应线,因为这是本产品的主要电源断开器。
设备操作规范
减少人身伤害或设备受损的危险:
•
•
•
移举设备时遵守当地的职业健康与安全要求。
借助机械手段或其他合适的手段移举设备。
拆除一切易分离组件,以降低重量并方便操作。
电源与电气警告
注意事项
电源按钮(如待机电源标记所示)并不能完全关闭系统的交流电源,只要系统已接
通电源,就存在 5V
待机电源。要从系统切断电源,须从墙壁电源插座中拔下交流电线。您的系统可能
不止使用一根交流电线。请确保所有的交流电线都已拔下。打开机箱或增加或去除
任何热插拔组件之前,确保交流电线已拔下。
若非所需的确切类型,请勿尝试修改或使用交流电线。系统的每个电源供应设备都
需要一根单独的交流电线。
本产品的电源供应设备包含非用户维修部件。请勿打开电源供应设备。电源供应设
备包含非常危险的电压级、电流级和能量级。请与生产商联系维修事宜。
替换热插拔电源供应设备时,请先拔下需替换的电源供应设备上的电源线,再将其
从服务器上移除。
112
Intel® Server Chassis SC5400 User’s Guide
为避免电击,请在打开服务器之前,关闭服务器并断开服务器上连接的电源线、电
信系统、网络和调制解调器。
电源线警告
如果产品未提供交流电线,请购买一根您所在国家批准使用的交流电线。
注意事项
为避免电击或火灾危险,请按如下所述对产品所用的电源线进行检查:
•
•
•
•
若非所需的符合接地插座的确切类型,请勿尝试修改或使用交流电线
电源线须符合以下标准:
⎯ 电源线的电气额定值须大于产品上标注的电流额定值。
⎯ 电源线须拥有适合插座的安全接地插头或触点。
电源线为交流电源的主要断开设备。插座须靠近设备并可随时断开。
电源线须插入所提供的拥有合适接地的插座。
系统使用警告
注意事项
为避免人身伤害或财产损失,无论何时检查产品内部,以下安全指导都适用:
•
•
•
•
•
•
•
•
关闭所有与本产品相连的外设。
按下电源按钮至关闭状态,关闭系统。
从系统或墙壁插座上拔下所有交流电线,断开交流电源。
断开与系统相连的所有线缆和通信线路。
卸除舱口盖时,保留所有螺钉及其他紧固件。完成产品内部检查之后,请
用螺钉或紧固件重新固定舱口盖。
请勿打开电源供应设备。电源供应设备内没有可维修部件。请与生产商联系
维修事宜.
增加或替换任何非热插拔组件之前,请关闭服务器电源并断开所有电源线
。
替换热插拔电源供应设备时,请先拔下需替换的电源供应设备上的电源线
,然后再从服务器上移除电源供应设备。
注意事项
如果服务器一直在运行,任何已安装的处理器和吸热设备都可能很热。除非要增加
或移除热插拔组件,否则请待系统冷却后再开盖。为避免在热插拔组件安装过程中
接触灼热组件,移除或安装热插拔组件时务须小心。
Intel® Server Chassis SC5400 User’s Guide
113
注意事项
为避免受伤,请勿触摸运转的风机叶片。如果系统的风机上配有防护装置,请勿卸
下风机防护装置运行系统。
机架固定件警告
设备的机架须固定在稳固的支座上,以防从中安装服务器或设备时倒塌。须按照机
架生产商提供的安装说明进行安装。
从下往上将设备安装在机架上,最重的设备安装在机架的最底层。
一次只从机架上安装一件设备。
您须负责安装整个机架装置的主要电源断开设备。此主要断开设备须随时可用,且
须标明为控制整个装置(而不仅限于服务器)的电源。
为避免潜在的电击危险,须对机架及其上所安装的每一件设备实行正确的安全接地
。
静电放电 (ESD)
注意事项
ESD 会损坏磁盘驱动器、主板及其他部件。我们建议您执行 ESD
工作站的所有步骤。如果没有 ESD
工作站,则采取一些静电放电保护措施,操作部件时,戴上与服务器上的机箱接地
或任何未喷漆金属表面连接的防静电腕带。
操作主板时始终保持小心。它们可能对 ESD
非常敏感。拿持主板时只接触边缘。从保护包装中或从服务器上取出主板后,请将
主板组件侧面朝上放置在无静电的接地表面上。请使用导电泡沫垫(若有),不要
使用主板包装。请勿将主板在任何表面上滑动。
114
Intel® Server Chassis SC5400 User’s Guide
其他危险
替换电池
注意事项
不正确替换电池可能导致爆炸危险。替换电池时,请只使用设备生产商推荐使用的
电池。
请按当地法规处置电池。
请勿对电池充电。
请勿拆卸、刺穿或以其他方式损坏电池。
冷却和气流
注意事项
按照说明小心布置线缆,尽量减少气流阻塞和冷却问题。
为保证适当的冷却和气流,运行系统时请确保机箱盖已安装。未安装机箱盖即运行
系统可能导致系统部件受损。安装机箱盖的步骤如下:
•
•
•
首先检查并确保系统内没有遗留的未固定工具或部件。
检查线缆、内插板和其他组件已正确安装。
按产品说明安装机箱盖。
激光外设或激光设备
注意事项
为避免幅射暴露和 / 或人身伤害:
•
请勿打开任何激光外设或激光设备的外壳
•
激光外设或激光设备为非用户维修设备
请与生产商联系维修事宜
Intel® Server Chassis SC5400 User’s Guide
115
116
Intel® Server Chassis SC5400 User’s Guide
Appendix C: Warranty
Limited Warranty for Intel® Chassis
Subassembly Products
Intel warrants that the Products (defined herein as the Intel® chassis subassembly and all
of its various components and software delivered with or as part of the Products) to be
delivered hereunder, if properly used and installed, will be free from defects in material
and workmanship and will substantially conform to Intel's publicly available
specifications for a period of three (3) years after the date the Product was purchased from
an Intel authorized distributor. Software of any kind delivered with or as part of products
is expressly provided "as is" unless specifically provided for otherwise in any software
license accompanying the software.
If any Product furnished by Intel which is the subject of this Limited Warranty fails during
the warranty period for reasons covered by this Limited Warranty, Intel, at its option, will:
• REPAIR the Product by means of hardware and/or software; OR
• REPLACE the Product with another Product; OR
• REFUND the then-current value of the Product if Intel is unable to repair or replace
the Product.
If such Product is defective, transportation charges for the return of Product to buyer
within the USA will be paid by Intel. For all other locations, the warranty excludes all
costs of shipping, customs clearance, and other related charges. Intel will have a
reasonable time to make repairs or to replace Product or to refund the then-current value
of the Product.
In no event will Intel be liable for any other costs associated with the replacement or
repair of Product, including labor, installation or other costs incurred by buyer and in
particular, any costs relating to the removal or replacement of any product soldered or
otherwise permanently affixed to any printed circuit board.
This Limited Warranty, and any implied warranties that may exist under state law, apply
only to the original purchaser of the Product.
Intel® Server Chassis SC5400 User’s Guide
83
Extent of Limited Warranty
Intel does not warrant that Products to be delivered hereunder, whether delivered standalone or integrated with other Products, including without limitation semiconductor
components, will be free from design defects or errors known as "errata." Current
characterized errata are available upon request.
This Limited Warranty does not cover damages due to external causes, including accident,
problems with electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improper installation, or improper testing.
Warranty Limitations and Exclusions
These warranties replace all other warranties, expressed or implied including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose.
Intel makes no expressed warranties beyond those stated here. Intel disclaims all other
warranties, expressed or implied including, without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do not allow the
exclusion of implied warranties, so this limitation may not apply.
All expressed and implied warranties are limited in duration to the limited warranty
period. No warranties apply after that period. Some jurisdictions do not allow limitations
on how long an implied warranty lasts, so this limitation may not apply to you.
Limitations of Liability
Intel's responsibility under this, or any other warranty, implied or expressed, is limited to
repair, replacement, or refund, as set forth above. These remedies are the sole and
exclusive remedies for any breach of warranty. Intel is not responsible for direct, special,
incidental, or consequential damages resulting from any breach of warranty under another
legal theory including, but not limited to, lost profits, downtime, goodwill, damage to or
replacement of equipment and property, and any costs of recovering, reprogramming, or
reproducing any program or data stored in or used with a system containing this product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights
that vary from jurisdiction to jurisdiction.
Any and all disputes arising under or related to this Limited Warranty shall be adjudicated
in the following forums and governed by the following laws: for the United States of
America, Canada, North America, and South America, the forum shall be Santa Clara,
California, USA, and the applicable law shall be that of the State of California, USA; for
the Asia Pacific region, the forum shall be Singapore and the applicable law shall be that
of Singapore; for Europe and the rest of the world, the forum shall be London and the
applicable law shall be that of the United Kingdom.
84
Intel® Server Chassis SC5400 User’s Guide
In the event of any conflict between the English language version and any other translated
version(s) of this Limited Warranty, the English language version shall control.
How to Obtain Warranty Service
To obtain warranty service for this Product, you may contact Intel or your authorized
distributor.
• North America and Latin America To obtain warranty repair for the product, please
go to the following Web site to obtain instructions: http://support.intel.com/support/
motherboards/draform.htm
• In Europe and in Asia Contact your original authorized distributor for warranty
service.
Any replacement Product is warranted under this written warranty and is subject to the
same limitations and exclusions for the remainder of the original warranty period.
Telephone Support
If you cannot find the information you need on Intel's World Wide Web site (http://
www.intel.com/), call your local distributor or an Intel Customer Support representative.
See “Getting Help” for telephone numbers.
Returning a Defective Product
Before returning any product, call your authorized dealer/distribution authority.
Intel® Server Chassis SC5400 User’s Guide
85
86
Intel® Server Chassis SC5400 User’s Guide
Appendix A: Getting Help
World Wide Web
http://support.intel.com/support/motherboards/server/SC5400.
Telephone
All calls are billed US $25.00 per incident, levied in local currency at the applicable credit
card exchange rate plus applicable taxes. (Intel reserves the right to change the pricing for
telephone support at any time without notice).
Before calling, fill out an Intel® Server Issue Report Form, available from the Web at
http://support.intel.com/support/motherboards/server/SC5400. For the fastest service,
submit your form via the Internet.
For an updated support contact list, see http://www.intel.com/support/9089.htm/
U.S. and Canada
1-800-404-2284
Europe
Belgium ..... 02 714 3182
Denmark ... 38 487077
Finland ...... 9 693 79297
France........ 01 41 918529
Germany ... 069 9509 6099
Holland ...... 020 487 4562
Italy............ 02 696 33276
Norway ...... 23 1620 50
Spain .......... 91 377 8166
Sweden....... 08 445 1251
UK.............. 870 6072439
Intel® Server Chassis SC5400 User’s Guide
67
In Asia-Pacific Region
Australia.... 1800 649931
Cambodia.. 63 2 636 9797 (via Philippines)
China ......... 800 820 1100 (toll-free)
.................... 8 621 33104691 (not toll-free)
Hong Kong 852 2 844 4456
India........... 0006517 2 68303634 (manual toll-free. You need an IDD-equipped
telephone)
Indonesia ... 803 65 7249
Korea ......... 822 767 2595
Malaysia .... 1 800 80 1390
Myanmar... 63 2 636 9796 (via Philippines)
New Zealand 0800 444 365
Pakistan..... 632 63684 15 (IDD via Philippines)
Philippines 1 800 1 651 0117
Singapore .. 65 6213-1311
Taiwan ....... 2 2545-1640
Thailand .... 1 800 631 0003
Vietnam ..... 632 6368416 (IDD via Philippines)
Japan
Domestic.... 0120 868686
Outside country
81 298 47 0800
Latin America
Argentina .. Contact AT&T USA at 0-800 222 1288. Once connected, dial 800 843 4481
Brazil ......... 001-916 377 0180
Chile
68
Easter Island.. ............ Contact AT&T USA at 800 800 311. Once
connected, dial 800 843 4481
Mainland and Juan .. Contact AT&T USA at 800 225 288. Once
connected, dial 800 843 4481
Intel® Server Chassis SC5400 User’s Guide
Colombia ... Contact AT&T USA at 01 800 911 0010. Once connected, dial 800 843 4481
Costa Rica . Contact AT&T USA at 0 800 0 114 114. Once connected, dial 800 843 4481
Ecuador
(Andimate) .... Contact AT&T USA at 1 999 119. Once connected,
dial 800 843 4481
(Pacifictel) ..... Contact AT&T USA at 1 800 225 528. Once connected, dial
800 843 4481
Guatemala. Contact AT&T USA at 99 99 190. Once connected, dial 800 843 4481
Mexico ....... Contact AT&T USA at 001 800 462 628 4240. Once connected, dial 800 843
4481
Miami ........ 1 800 621 8423
Panama...... Contact AT&T USA at 00 800 001 0109. Once connected, dial 800 843 4481
Paraguay ... 001 916 377 0114
Peru ........... 001 916 377 0114
Uruguay..... 001 916 377 0114
Venezuela... Contact AT&T USA at 0 800 2255 288. Once connected, dial 800 843 4481
Intel® Server Chassis SC5400 User’s Guide
69
70
Intel® Server Chassis SC5400 User’s Guide
Download PDF

advertising