Operating instructions | Electrolux 502 D Ventilation Hood User Manual

502 D
Extractor Hood
Installation and Operating Instructions
Contents
Electrical connections .......................................................... 4
Safety warnings for electricians .............................................. 4
Appliances with 2 wires .......................................................... 5
Safety warnings for kitchen unit installer ................................ 6
General details ........................................................................ 7
Extractor version ..................................................................... 7
Filter Version ........................................................................... 8
Description of the appliance ................................................ 9
Technical details ................................................................... 9
Fixing the hood ..................................................................... 10
Safeting warnings for user .................................................... 11
Hood operation ..................................................................... 12
Care and maintenance ........................................................ 13
Metal grease filter ................................................................ 13
Charcoal filter ........................................................................ 14
Replacing the lamps ............................................................. 15
Cleaning ................................................................................ 15
Special accessories ............................................................ 16
Technical assistance service ............................................. 16
3
Electrical connections
Safety warnings
for electrician
It must be ensured that the voltage and current indicated on the
rating plate agree with the voltage of the user to electricity supply.
If the appliance has been equipped with a mains lead with a
moulded-on type plug, the following regulations must be comply
with:
The plug moulded on to the lead incorporates a fuse. For
replacement, use a 5 amp BS1362 fuse. Only ASTA approved or
certified fuses should be used. If the fuse cover/carrier is lost, a
replacement cover/carrie must be obtained from an electrical
goods retailer. If the socket outlets are not suitable for the plug
fitted to the appliance, then the plug must be cut off and destroyed
for safety reasons, and an appropriate plug be fitted.
When wiring the plug ensure that all strands of wire are securely
retained in each terminal. Do not forget to tighten the mains lead
clamp on the plug.
Electrical connections
230 V - using fixed power supply line with plug.
240 V - using fixed power supply line (Great Britain).
Fuse rating 13 amps
(The unit should only be connected up by an authorized electrician).
See rating plate for further information.
It is recommended that the socket for the plug is sited above the
cooker hood or above the overhead cabinet.
This has 2 advantages:
1) The socket is not visible.
2) The appliance can easily be unplugged when necessary.
If a fixed connection is required the cooker hood should be
connected by an electrical installer registered with a competent
electricity company. An isolating device is to be provided on the
fixed wiring side. Switches with a contact opening of more than
3mm apply as isolating devices.
These include-automatic cut-out switches, fuses and contactors
(VDE 0730, s. 7, Part1).
4
Electrical connection for the UK
The appliance must be connected to fixed wiring with a double
pole switched fused spur outlet with or without pilot lamp.
Appliances
with 2 wires
We strongly recommend the appliance to be connected only by
a qualified electrician who is a member of the NICEIC who will
comply with the IEE and any local regulations.
NOTE:
The terminology “DOUBLE POLE” means that both the live
and the neutral supplies are switched and disconnected at
the same time.
The terminations labelled SUPPLY are for the connection for the
internal house wiring and the terminations labelled LOAD are
for the appliance.
IMPORTANT
The wires of the mains lead supplied with this appliance are
coloured in accordance with the following code:
Blue-Neutral
Brown-Live
As the colours of the flexible cord of this appliance may not
correspond with the coloured markings identifying the terminals in the plug, proceed as follows: The wire which is
coloured brown must be connected to the terminal which is
marked with the letter L or coloured red.
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
BLUE
(NEUTRAL)
BROWN
(LIVE)
L
LOAD
L
N
SUPPLY
LOAD
FUSE
ON
DP 13A, 250V
N SUPPLY
5
Safety warnings
for kitchen unit
installer
When the unit is used in its extractor version, a sufficiently large
ventilation hole must be provided, with dimensions that are
approximately the same as the outlet hole.
The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be
connected to ventilation ducts for rooms in which fuel-burning
appliances are installed.
It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney
flue or combustion gas duct.
The air outlet installation must comply with the regulations laid
down by the relevant authorities.
National and regional building regulations impose a number of
restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas
fires, in the same room.
The local decree on fuel-burning systems specifies a maximum
depression of 0.04 mbar in such rooms.
Hoods can only be used safely with appliances connected to a
chimney if the room and/or flat (air/environment combination) is
ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the possibility of negative
pressure being created during operation of the hood.
If you have any doubts, contact the relevant controlling authority
or building inspector’s office.
Since the rule for rooms with out fuel burning appliances is “air
inlet should be same size as extractor outlet hole”, an aperture of
500-600 cm2, which is to say a larger hole, could reduce the
performance of the extractor hood.
If the hood is used in its filtering version (carbon filter), it will
operate simply and safely in the above conditions without the
need for any of the aforementioned measures.
When the hood is used in its extractor function, the following rules
must be followed to obtain optimal operation:
— short and straight outlet hose
— minimum number of bends in the outlet hose
— Install hoses with an acute angle, always following a gentle
curve only
— hose as large as possible (100 mm Ø).
6
Failure to observe these basic rules will drastically reduce the
performance and increase the noise levels of the extractor hood.
When used as an extractor unit, the hood must be fitted with a
100mm diameter hose.
If the fumes must be forced out through the wall, you must obtain
a MKZ sizable wall exhaust pipe (with external exhaust and air
intake), E-Nr.- 610 899 004 (Ø 120 mm) which is one of our
optional parts.
When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/
ring surfaces:
electric cookers
650 mm
gas cookers
700 mm
coal and oil cookers
900 mm min.
Where flexible ducting is fitted the length should be no more
than:
— 3 metres with one 90° bend
— 2 metres with two 90° bends.
Bends of more than 90° will reduce the efficiency of the hood
and reduce the air flow.
General details
The hood is supplied as a ducted version, but may also be used
in recirculation mode by inserting a charcoal filter (Special
accessories).
Extractor
version
The air is ducted out through a pipe which is connected to the
outlet hole A (fig. 1) by means of a coupling flange B.
To connect the hood to a wall box, you use hoses and wall boxes
as offered on the AEG price list as optional extras.
B
A
1
7
Filter version
Cooking vapours are cleaned by the charcoal filter (Special
accessories) and ducted back into the kitchen.
The AEG original KF-Plus charcoal filter is necessary for the
recirculating mode (see paragraph “Special accessories”).
For the recirculating mode proceed as follows:
a) Remove the grid by turning knob A (fig. 2).
b) Position the filter (fig. 3) and rotate clockwise until it stops.
In this mode air will be expelled through an exhaust pipe with
an internal diameter of 100 mm on the top of the cupboard.
c) Replace the grid.
A
2
3
8
A
Description of the appliance
1) Light switch
2) Motor switch
3) Work surface lamp
4) Grid
3
4
2
1
Technical details
Model
502 D
Net weight:
Height
Width
Depth
5 kg
145 mm
520 mm
285 mm
Absorbed power:
160W
Motor:
1 x 120 W
Lighting:
1 x 40 Watt
Lengt of the cable: 110 cm
Fan powers (speed), speed in compliance with DIN 44971
Speed:
1
Extractor version: 126 m3/h
Filter version:
110 m3/h
2
3
149 m3/h
133 m3/h
185 m3/h
170 m3/h
Flange: 100 mm Ø
9
Fixing
the hood
After having adjusted the hood for the version required, it may be
installed.
This appliance is designed for fitting in a cabinet or some other
support.
The opening to be made on the bottom of the wall-hung cabinet
must correspond with the measurements shown in fig. 4
(495 X 260 mm).
To fix the hood proceed as follows:
a) remove the grid.
b) Fit the hood into the opening.
c) Secure the unit to the cabinet by screwing up screws through
holes C (fig. 4).
d) Replace the grid.
C
C
4
10
The hood is fitted with one variable speed motor.
The most effective use of the hood is obtained by switching it on
a few minutes before you start cooking and leaving it on a for
approximately 5-15 minutes after having finished, thus ensuring
that all that cooking odours are eliminated.
Safety warnings
for user
Never leave a cooking hob or ring on without a pot or pan on
top of it, to avoid the possibility of excess heat damaging the
unit. Gas, oil or coal cooker flames in particular should never
be left uncovered.
Special care should be taken when using deep fat fryers
since the oil in them can overheat and burst into flames.
The risk of fat catching fire is increased when using dirty oil.
It is extremely important to note that overheating can cause
a fire.
Never carry out any flambé cooking under the hood.
Always disconnect the unit from the power supply before
carrying out any work on the hood, including replacing the
light bulb (take the cartridge fuse out of the fuse holder or switch
off the automatic circuit breaker).
It is very important to clean the hood and the grease filters at
the recommended intervals. Failure to do so could cause
grease deposits to build up, causing a fire hazard.
11
Hood Operation
Controls
The hood is fitted with a variable speed motor. The most effective
use of the hood is obtained by switching it on a few minutes before
you start cooking and leaving it on a for approximately 15 minutes
after you have finished, thus ensuring all cooking odours are
eliminated. The control switches are located on the unit’s front
panel: the light switch (A) switches the hood lamp on and off;
the motor switch (B) switches the cooking smoke and vapour
extractor motor on and off, enabling you to select one of the three
different speeds.
B
A
12
Care and Maintenance
Before performing any maintenance operation, disconnect the
hood from the electricity.
Metal
grease filter
The hood has a metal grease filter.
To clean the filter, proceed as follows:
Open the grill by turning knob A (fig. 2).
A
A
2
Pull the two plastic stops B as shown by the arrows (fig. 5) and
remove the metal filter.
B
B
5
You should take out the metal filter every four weeks and wash it
either in the dishwashing machine or by hand.
Clean the internal housing only with warm washing-up water — do
not use any harsh cleaners, brushes, or abrasive.
Soak metal filter cassette for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Repeat the
process if necessary. Re-fit the cassette when it is dry.
Hand-washing
Place metal filter cassette in dishwasher. Select most powerful
washing program and highest temperature, at least 65° C. Repeat the
process. Re-fit the cassette when it is dry.
When washing the metal grease filter in the dishwasher a slight
discoloration of the filter can occur.
Dishwashing
machine
13
Charcoal
filter
The charcoal filter must be changed at least every 4 months.
The charcoal filter cannot be washed or regenerated.
The hood can only work well in the recirculating mode if the AEG
recommended filter has been used, the filter is changed as
recommended in this section and if the hood is cleaned and
maintained as instructed in this booklet.
Therefore follow the instructions closely for best performance.
The charcoal filter deals with odours which are created during
cooking.
Pull the two plastic stops B as shown by the arrows (fig. 5) and
remove the metal filter.
New charcoal filters are available from AEG or your retailer; it
must not be washed.
To remove rotate the filter in anticlockwise (Fig. 3).
Re-fit the metal filter
3
Attention
Failure to observe the rules for cleaning the appliance and
changing and cleaning the filters may cause fires. Therefore, we
recommend you follow these instructions carefully.
14
Always turn off the electricity before replacing lamps!
Replacing
the lamps
1) Remove the grid (Fig. 2) in order to check the lamps and
replace them if necessary.
A
A
2
2) Unscrew the lamps that do not work and replace them with
40W max lamps (E14).
If the light does not function, check that the lamps are properly
screwed before contacting a customers’ service centre.
Warning: always disconnect the hood from the mains power
supply before cleaning it.
Never insert pointed objects in the motor’s protective grille.
Cleaning
Wash the outside surfaces using a mild detergent solution.
Never use caustic detergents or abrasive brushes or powders.
Only ever clean the switch panel and filter grille using a damp
cloth and mild detergents.
It is extremely important to clean the unit and change the
filters at the recommended intervals. Failure to do so will
cause grease deposits to build up that could constitute a fire
hazard.
Attention
Failure to observe the rules for cleaning the appliance and
changing and cleaning the filters may cause fire. Therefore,
properly observing these instructions is highly recommended.
15
Special accessories
See AEG price-list for wallbox and hose accessories.
KF-Plus charcoal filter
E-Nr. 942 118 620
Technical assistance service
You are welcome to telephone our technical assistance service
(see list of technical assistance centres) whenever you need
information or in the unlikely event of a fault.
When calling, please be ready to specify:
1. The model code number
2. The serial number (E-Nr.)
3. The manufacturing number (F-Nr.)
This information is shown on the registration plate inside the
unit behind the grease filter grille.
We reserve the right to change specifications and colours as a
result of our policy of continuing technological development.
16
AEG Hausgeräte AG
Postfach 1036
D-90327 Nürnberg
© Copyright by AEG
H 259 226 140
L 650A
Download PDF

advertising