Operating instructions | Electrolux 50815 Washer/Dryer User Manual

LAVAMAT 50815
Washing machine
User information
Dear Customer,
Please read this user information carefully and keep it to refer to later.
Please pass the user information on to any future owner of the appliance.
1
3
2
2
The following symbols are used in the text:
Safety instructions
Warning! Information that affects your personal safety.
Important! Information that prevents damage to the appliance.
Useful tips and hints
Environmental information
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Programme overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Before the first wash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparing and sorting washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Running a wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the door/loading washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding detergent/conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching on the appliance/selecting a programme . . . . . . . . . . . . . . . . . . .
Changing the spin speed/selecting rinse hold . . . . . . . . . . . . . . . . . . . . . . . .
Programme Option Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRE WASH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIME SAVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating RINSE+. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the delay timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupting a programme/adding washing . . . . . . . . . . . . . . . . . . . . . . . . . .
Washing cycle complete/Removing the washing. . . . . . . . . . . . . . . . . . . . . .
11
11
11
12
13
13
13
13
14
14
15
15
15
Child safety device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remedying small faults yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If the wash result is not satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carrying out an emergency drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drain pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
18
20
21
22
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Consumption values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3
Installation and connection instructions. . . . . . . . . . . . . . . . .
25
Safety information concerning installation . . . . . . . . . . . . . . . . . . . . . . . . 25
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Where to install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making the appliance level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
26
29
29
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Connecting to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Water Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Guarantee/Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service and Spare Parts
4
34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Operating Instructions
1 Safety
Prior to using the appliance for the first time
• Follow the “Installation and connection instructions”.
• If the appliance is delivered in the winter months when there are minus temperatures: store the washing machine at room temperature
for 24 hours before using for the first time.
Correct use
• The washing machine is only designed for the washing of normal domestic laundry at home.
• Additions or modifications to the washing machine are not permitted.
• Only use detergents/conditioners that are suitable for use in domestic
washing machines.
• The washing must not contain any flammable solvent. The risk of explosion exists.
• Do not use the washing machine for dry cleaning.
• Dyes/colour removers may only be used in the washing machine, if
the manufacturer of these products expressly permits this. We cannot
accept liability for any damage arising.
Child safety
• Keep packaging away from children. There is a risk of suffocation.
• Children often do not recognise the hazards associated with electrical
appliances. Do not allow children to use the washing machine unsupervised.
• Make sure that children and pets do not climb into the drum of the
washing machine. The risk of death exists.
5
General safety
• Repairs to the washing machine may only be carried out by qualified/
authorised service engineers.
• Never use the appliance when the electrical cable is damaged or the
control panel, worktop or plinth area are damaged to such an extent
that the inside of the appliance is openly accessible.
• Switch off the washing machine prior to cleaning it and carrying out
maintenance. In addition, remove the power plug from the power
point or – if the appliance has been hard-wired – switch off the cutout in the fuse box or completely remove the fuse.
• If operation is stopped, disconnect the appliance from the mains supply and turn off the tap.
• Never remove the power plug from the power point by pulling on the
cable. Always pull the plug.
• Multiway-plugs, connectors and extension cables must not be used.
Resulting overheating may constitute a fire hazard.
• Never wash the washing machine down with a water jet. Danger of
electric shock.
• When using wash programmes with high temperatures the glass in
the door will become hot. Do not touch it!
• Before emergency emptying of the appliance, before cleaning the
drain pump or opening the door in an emergency, let the water cool
down.
• Small animals can nibble on electrical cables and water hoses. This
can constitute a risk of electrocution and water damage. Keep small
animals away from the washing machine.
6
Description of the appliance
Detergent dispenser
drawer
Control panel
Rating plate
(behind door)
Plinth flap/
Drain pump
Screw feet
(height adjustable)
Control panel
Spin/RINSE HOLD button
Additional programme
buttons
DELAY TIMER button
Programme progress display
DOOR indicator
Programme selector
START/PAUSE button
7
Programme overview
COTTONS/LINEN
95, 60, 40, 30
6 kg
•
EASY-CARES
60, 40
3kg
EASY IRON 40
•
•
•
•
•3)
•
•
•
•
•
•
•
•
•
•
1kg
•
•
•
•
•
•
DELICATES
40, 30
3kg
•
•
•
•
•
•
WOOL/SILK H (Hand-washing)
30, COLD
2kg
•
•
•
•
RINSE
3kg
•
•
•
•
6kg
•
•
•
Programme
TIME SAVER
RINSE HOLD
•
600
6kg
800
PRE WASH
ENERGY SAVING2)
Spin speed
1000
max. load 1)
(dry washing)
Additional
programmes
DRAIN
SPIN
1) A 10 litre bucket contains approx. 2.5 kg of dry washing (cotton)
2) Programme settings for tests in accordance with or in support of EN 60 456 and IEC 60 456 are described in the section “Consumption values”.
3) Recommended load for short progammes is 3kg; full loading is possible however with somewhat reduced
cleaning results.
8
Application/Features
Energy-saving programme at 60°C for lightly to normally soiled whites/coloureds made of cotton/linen.
Programme for normally to heavily soiled coloureds/whites made of cotton/
linen.
Programme for easy-care mixed fibres and synthetics.
Special programme at 40°C for easy-care fabrics which after being washed
using this programme need to be ironed only lightly or not at all.
Gentle programme for delicate fabrics such as bonded fibres, micro-fibres,
synthetics, net curtains (load max. 20 to 25 m2 net curtains). With RINSE
HOLD also suitable for materials that have climatic membranes, e.g. outdoor
clothing.
Special gentle programme for machine and hand-washable wool/silk.
Separate gentle rinse (3 rinse cycles, liquid conditioner is washed in from the
compartment w, spin). Not suitable for wool. When loading easy-care or
delicate items, reduce the spin speed.
Care
symbols1)
MO
JMO
IKN
KN
IK
QLH
JMO
Draining following a rinse hold.
Draining and spinning, e.g. following a rinse hold, or separate spinning of
hand-washed cottons/linen. Reduce the spin revolution speed if spinning
easy-care, delicate or woollen items.
JMO
1) The figures in the care symbols indicate the maximum temperatures.
9
Before the first wash
1. Open the detergent drawer.
2. Pour approx. 2 litres of water through the detergent drawer into the
washing machine.
This closes the water container when the next programme is started
and the economy valve can function properly
3. To remove any production-related residues from the drum and water
tank, perform the first wash cycle without a load. Programme: COTTONS/LINEN 95, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.
Preparing and sorting washing
Preparing washing
• Empty the pockets. Remove foreign bodies (e.g. coins, paper clips,
nails, etc.).
• Do up zips, button up covers to prevent damage to washing.
• Remove the runners from net curtains or cover them with a net or a
bag.
• Wash delicate and small items in a net/pillowcase, e. g. net curtains,
tights, small socks, handkerchiefs, bras.
Important: Underwired Bras must NOT be machine washed. Small items
should be placed in a net bag/pillow case.
Sorting washing
• By colour: Wash white and coloured washing separately. Washing can
run.
• By temperature, type of washing and care symbol.
Important: Do not wash fabrics with the G care symbol (= do not
wash!) in the washing machine.
10
Running a wash cycle
Opening the door/loading washing
1. Open the door: pull the handle on the door.
When the appliance is switched on, the DOOR and START/PAUSE indicators show whether the door can be opened:
DOOR indicator
START/PAUSE indicator
Can the door be opened?
flashing
flashing
yes, after approx. 2 minutes
illuminated
illuminated
no, water level and/or
temperature too high
is off
flashing
yes
2. Separate washing and load loosely.
Mix large and small items.
Important: Do not get any washing
caught between the door and the
rubber seal.
3. Firmly push the door shut. Door
catch must audibly click shut.
Adding detergent/conditioner
Important! Only use detergents/conditioners that are suitable for use
in domestic washing machines.
Add detergent/conditioner in accordance with the detergent/conditioner manufacturer’s instructions. Observe instructions on the packaging.
The amount of detergent used depends on:
– the washing’s degree of soiling,
– the load size
– the hardness of the tap water.
• If the manufacturer does not make any recommendations with regard to small volumes of washing: for a half-load use a third less, and
for a very small load use only half the amount of detergent that is
recommended for a full load.
• Water softener should be used from water hardness range 2 (=medium). The amount of detergent used can then always be that as for
hardness range 1 (=soft). Your local water company will provide you
with information about water hardness in your area.
11
1. Pull out the detergent drawer as far as it will go.
2. Add the detergent/conditioner.
3. Push the detergent drawer in fully.
Washing powder/tablets
for the main wash cycle
Conditioner/
Wash-care products
to preserve the shape
of garments/
Starch
Washing powder/tablets
for the pre wash cycle or
in-wash stain treatment
Washing powder/tablets for the main wash cycle
If you are using water softener and require the right-hand compartment for detergent for the pre wash cycle/in-wash stain treatment, add
the water softener on top of the detergent for the main wash cycle in
the left-hand compartment.
Softener, wash-care products to preserve the shape of garments,
starch
Fill the compartment to no more than the MAX indicator. Add water to
thick liquid concentrates in accordance with the manufacturer’s instructions before using them. Dissolve powder starch.
If you are using liquid detergent:
Add liquid detergent using the dosage containers provided by the detergent manufacturer.
Switching on the appliance/selecting a programme
Set the programme and temperature using the programme selector.
3
12
The machine is switched on by selecting a programme.
The programme progress display
shows the programme steps that
the selected programme will carry
out.
Changing the spin speed/selecting rinse hold
3
The washing machine suggests the
maximum permitted spin speed
suitable for the selected programme. You can reduce this spin
speed:
To do this, press the Spin/RINSE
HOLD button repeatedly until the required speed is indicated.
The spin speed for the final spin can still be changed during the programme. To do this:
1. Press the START/PAUSE button.
2. Change the spin speed.
3. Press the START/PAUSE button again.
RINSE HOLD
With RINSE HOLD the washing is left to soak in the final rinse water.
There is no final spin after the intermediate spin(s). The intermediate
spin depends on the programme and cannot be changed.
Programme Option Buttons
If required, press the additional
programme button(s). The corresponding indicator will illuminate.
PRE WASH
Warm pre-wash before the main wash that follows automatically; with
intermediate spin for COTTONS/LINEN and EASY-CARES/EASY IRON,
without intermediate spin for DELICATES.
TIME SAVER
Shortened wash programme for lightly soiled washing.
13
Activating/deactivating RINSE+
If RINSE+ is activated, two additional rinse cycles take place with the
programmes COTTONS/LINEN, EASY-CARES/EASY IRON, DELICATES and
RINSE. RINSE+ remains permanently saved – even after the appliance
has been switched off.
Activating RINSE+:
1. Turn the programme selector to COTTONS/LINEN, EASY-CARES/EASY
IRON or DELICATES (with the temperature of your choice).
2. Simultaneously press and hold the PRE WASH and DELAY TIMER buttons until RINSE and RINSE+ are illuminated on the programme
progress display. RINSE+ has now been permanently activated.
Prior to the start of a programme RINSE+ is illuminated in the programme progress display and while the additional rinse cycles are being
performed.
Deactivating RINSE+
1. Turn the programme selector to COTTONS/LINEN, EASY-CARES/EASY
IRON or DELICATES (with the temperature of your choice).
2. Simultaneously press and hold the PRE WASH and DELAY TIMER buttons until RINSE+ goes out on the programme progress display. RINSE+
is now permanently deactivated.
Setting the delay timer
3
14
The DELAY TIMER button allows you to delay the start of a programme.
1. Select the programme.
2. Press the DELAY TIMER button once if the wash programme is to start
in 6 hours. The 6h indicator will illuminate.
Press the DELAY TIMER button twice if the wash programme is to start
in 3 hours. The 3h indicator will illuminate.
If you press the DELAY TIMER button again, the delay timer will be cancelled. The indicator will go out.
3. To activate the delay timer, press the START/PAUSE button.
Note: If a time delay of 6 hours is selected, the 6h indicator will illuminate. After 3 hours the display will switch and 3h will be illuminated.
After a total of 6 hours the wash programme will then start.
Starting a programme
3
1. Check that the tap is turned on.
2. Press the START/PAUSE button. The programme is started or will start
after the delay timer has counted down.
During the wash programme the current stage of the programme will
be shown in the programme progress display.
If after pressing the START/PAUSE button the END indicator flashes 4x,
the door has not been correctly shut. Push the door firmly closed and
press the START/PAUSE button again.
Interrupting a programme/adding washing
Interrupting a programme
• A washing programme can be interrupted at any time by pressing the
START/PAUSE button and then re-started by pressing the START/
PAUSE button again.
• To cancel a programme before it has ended, turn the programme selector to OFF. Important! Be careful of water in the appliance.
Adding washing
Washing can be added as long as the DOOR indicator is not illuminated.
1. Press the START/PAUSE button. The door can be opened.
2. Close the door and press the START/PAUSE button again. The programme will continue.
Washing cycle complete/Removing the washing
When the programme has finished, END will illuminate in the programme progress display. As soon as the DOOR indicator goes out and
the END indicator illuminates, the door can be opened.
1. Open the door and remove the washing.
2. Turn the programme selector to OFF.
3. Turn off the tap.
4. After washing, pull out the detergent drawer a little to allow it to dry.
Keep the door very slightly open so that the washing machine can air.
15
If RINSE HOLD has been selected:
Following a rinse hold DOOR and END will illuminate in the programme
progress display.
First the water must be drained:
– Either turn the programme selector to OFF, then to DRAIN and press
the START/PAUSE button (the water will be drained without spinning),
– or turn the programme selector to OFF and then to SPIN. Depending
on the type of washing, if required, reduce the spin speed and press
the START/PAUSE button (the water will be drained and the washing
spun).
Child safety device
If the child safety device has been activated, the door can no longer be
shut.
Activating the child safety device:
Use a coin to turn the knob (on the
inside of the door) in a clockwise direction as far as it will go.
1
Warning! The knob must not be depressed after being set, otherwise
the child safety device is not activated. The knob must stand out as
shown in the illustration.
Deactivating the child safety device:
Turn the knob in an anti-clockwise direction as far as it will go.
16
Cleaning and maintenance
Important! Do not use furniture care products or aggressive cleaners to
clean the appliance.
Wipe control panel and body with a damp cloth.
Cleaning procedure
If you plan to wash mainly at low temperature, you should run a hot
programme from time to time. This will reduce any deposits and clean
the appliance from the inside.
Detergent dispenser drawer
The detergent dispenser drawer should be cleaned regularly.
1. Remove the detergent dispenser drawer by pulling it firmly.
2. Remove the conditioner insert from
the middle compartment.
3. Clean all parts with water.
4. Put the conditioner insert in as far as
it will go, so that it is firmly in place.
5. Clean all parts of the washing machine, especially the nozzles in the
top of the washing-in chamber, with
a brush.
6. Insert the detergent dispenser drawer in the guide rails and push it in.
Washing drum
Rust deposits in the drum may occur due to rusting foreign bodies in
the washing or tap water containing iron.
Important! Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool.
1. Remove any rust deposits on the drum with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing to clean off any cleaning
agent residues. Programme: COTTONS/LINEN 95, press the TIME SAVER
button, add approx. 1/4 measuring cup of detergent.
17
Door and rubber collar
Regularly check whether deposits or foreign bodies are present in the
folds of the rubber collar or on the inside of the glass door.
Clean the glass in the door and the rubber collar regularly.
What to do if...
Remedying small faults yourself
If the programme progress display indicates one of the following fault
codes during operation:
– END flashes 1x (problem with water inlet),
– END flashes 2x (problem with water outflow),
– END flashes 4x (door open),
please consult the following table.
After the fault has been remedied, press the START/PAUSE button
In the case of other fault messages (one or more flashing indicators on
the programme progress display):
switch the appliance off and on again. Set the programme again. Press
the START/PAUSE button.
If the fault appears again, please contact your local Service Force Centre.
Problem
Possible cause
Power plug not plugged in
or problem with the fuse.
Washing machine does
not work.
Connect the plug to a mains
socket. Check the fuse.
The door is not shut proper- Close the door - there should
ly.
be an audible click.
The START/PAUSE button
was not pressed for long
enough.
18
Remedy
Press the START/PAUSE button for longer.
The door cannot be
closed.
The child safety device is ac- Deactivate the child safety
tivated.
device.
The END indicator is
flashing 4x.
The door is not closed prop- Close the door properly. Reerly.
start the programme.
Problem
Possible cause
The tap is turned off.
The END indicator is
The filter in the inlet hose
flashing 1x.
screw connection is blocked.
(Problems with the water inflow.)
The tap is blocked by limescale or is faulty.
Remedy
Turn on the tap.
Turn off the tap. Unscrew the
hose, remove the filter and
clean it.
Check the tap and have it repaired, if necessary.
The transport lock has not
Removing the transport lock.
been removed.
The washing machine
vibrates when operating
Adjust the feet as described
The screw feet not correctly
or is not stable.
in the installation and conadjusted.
nection instructions.
Washing has not been
spun.
Only a few large items of
washing in the drum.
Always load the drum as full
as possible. Mix large and
small items.
The inlet hose screw connection is leaking.
Tighten the inlet hose.
The outlet hose is leaking.
Replace outlet hose.
Water is running out
The drain pump lid has not
from under the washing been closed properly.
machine.
Washing was caught in the
door.
Close the cover properly.
Load washing carefully for
the next wash.
The emergency drain hose is Screw on the emergency
leaking.
drain hose firmly.
There is a lot of foam.
Too much detergent has
probably been used.
Follow the manufacturer's
instructions exactly when
measuring out detergent.
There is a kink in the outlet
hose.
Straighten the hose.
The maximum pump height
of 1m has been exceeded.
Please contact your local
Service Force Centre
The END indicator is
flashing 2x.
(Problems with the waThe drain pump is blocked.
ter outflow.)
Switch off the appliance.
Disconnect the power plug.
Clean the drain pump. Remove foreign bodies from
the pump housing.
For sink spigot connections:
Clean the spigot.
the spigot is blocked.
19
Problem
Conditioner has not
been rinsed in, compartment w for conditioner is filled with
water.
Possible cause
The conditioner insert in the
Clean the detergent drawer,
compartment for additives
insert the conditioner insert
has not been correctly infirmly.
serted or is blocked.
The door is locked.
The door cannot be
opened when the wash- There has been a power cut.
ing machine is switched (All the indicators have gone
on.
out.)
The door remains locked for
approx. 2 minutes.
The washing is badly
creased.
Remedy
Perhaps too many items
were loaded.
Wait until the DOOR indicator goes out and the END indicator illuminates.
The programme will continue
when the power cut has ended.
To remove the washing:
If water can be seen in the
appliance, first empty the
water before opening the
door (see section “Carrying
out an emergency drain”).
Observe the maximum load
volume.
If the wash result is not satisfactory
The washing is grey and there are limescale deposits in the drum
• Too little detergent was used.
• An incorrect detergent was used.
• Individual stains were not pre-treated.
• The programme or temperature was not set properly.
There are grey stains on the washing
• Items that were soiled with ointments, fats or oils were washed using
too little detergent.
• The wash temperature used was too low.
• A common cause is that conditioner – in particular the type in concentrated form - has come in contact with the washing. Wash out
such marks as soon as possible and exercise care when using the said
conditioner.
Foam can still be seen following the final rinse
• Modern detergents can cause foam to be created even during the final rinse. In spite of this, the washing has been sufficiently rinsed.
20
There are white residues on the washing
• What can be seen here are insoluble substances which modern detergents contain. They are not the result of insufficient rinsing.
Shake or brush the washing. If possible turn the washing inside out
before washing. Check your choice of detergent. Especially with dark
colours it is advisable to use liquid detergents.
Carrying out an emergency drain
1
Warning! Prior to carrying out an emergency drain, switch off the
washing machine and remove the power plug from the power point.
Warning! The water that comes out of the emergency drain hose may
be hot. There is a risk of scalding. Let the water cool before performing
an emergency drain!
1. Open the plinth flap and remove it.
2. Remove the emergency drain hose.
3. Place a shallow container underneath it. Then loosen the drain plug
by turning it in an anti-clockwise
direction and pull it out.
4. The water will run out. If it is necessary to empty the container more
than once, seal up the emergency
drain hose with the drain plug while
you are doing so.
When the water has all drained away:
5. Insert the plug firmly into the emergency drain hose and turn it in a
clockwise direction until it is firmly in place.
6. Replace the emergency drain hose into the retainer.
7. Insert the plinth flap into place and close it.
21
Drain pump
1
The drain pump is maintenance-free. It is only necessary to open the
pump cover if there is a malfunction and water is no longer being
pumped out, e.g. if the pump wheel is blocked.
Before loading the machine, please always ensure that there are no foreign bodies present in the pockets or in between the items to be
washed. Paper clips, nails, etc. which may find their way into the washing machine along with the washing will remain in the drain pump
housing (foreign body trap that protects the pump wheel).
Warning! Before opening the cover of the drain pump, switch off the
washing machine and remove the power plug from the power point.
1. First carry out an emergency drain.
2. Place a cloth on the floor in front of the cover of the drain pump.
Residual water runs out.
3. Unscrew the pump cover in an anticlockwise direction and remove it.
4. Remove foreign bodies and fluff
from the pump housing and from
the pump wheel.
5. Check whether the pump wheel
right at the back of the pump housing can turn. (If the wheel rotates
with a jerky motion, this is normal.)
If the pumping wheel cannot be
turned, please contact your local
Service Force Centre.
6. Insert the pump cover. Insert the
guides at the sides of the cover into
the guide slots and tighten the cover by turning in a clockwise direction.
7. Close off the emergency drain hose
and place it in the retainer.
8. Close the plinth flap.
22
Disposal
2
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging materials in the appropriate
container at your local waste disposal facilities.
Old appliance
W
1
The symbol
on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you
purchased the product.
Warning: When your appliance has finished its working life, remove
the plug from the mains socket. Cut off the cable and plug and dispose
of them.
Destroy the door lock. This prevents children from trapping themselves
inside and endangering their lives.
23
Technical data
5
This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending
Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x Width x Depth
850 x 598 x 603 mm
Depth when door is open
980 mm
Height adjustment
approx. +10/-5mm
Load (depending on programme)
Max. 6kg
Area of use
Domestic
Drum spin speed
see Rating Plate
Water pressure
1-10bar (=10–100N/cm2=0.1–1.0MPa)
Consumption values
The consumption values were obtained under standardised conditions.
They can differ in household use.
Programme selector
(Temperature)
Load size
in kg1)
Water
in litres
Energy
in kWh
Time in
minutes
6
62
2,20
146
6
49
1,12
125
COTTONS/LINEN 40
6
58
0,70
129
EASY-CARES 40
3
58
0,52
80
DELICATES 30
3
58
0,42
66
WOOL/SILK H (Hand-washing) 30
2
54
0,45
54
COTTONS/LINEN 95
ENERGY SAVING
2)
1) The load size is determined in accordance with the EN 60456 standard load.
2) Note: Programme setting for tests in accordance with or in support of standard
EN 60 456 and IEC 60 456. Actual consumption will vary from the indicated values
depending on water pressure, water hardness, water temperature at filling, room
temperature, type and quantity of washing, detergent used, variations in mains voltage and any additional programme functions selected.
24
Installation and connection instructions
1 Safety information concerning
installation
• This washing machine cannot be built-in.
• Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged to the mains. In the event of
damage to the appliance contact your supplier.
• Be sure to remove all the components of the transport lock before using the appliance for the first time. Otherwise when spinning damage
may be caused to the appliance or to neighbouring units or furniture.
• Before using the appliance for the first time, splash protection must
be completed. (See “Removing transit packaging”).
• Always plug the mains plug into a correctly installed shockproof
socket.
• If hard-wired: hard-wiring to the mains may only be carried out by
an a qualified electrician.
• Prior to using the appliance for the first time, ensure that the rated
voltage and current on the rating plate match the mains voltage and
current where the appliance is to be installed. The required fuse protection is also to be found on the rating plate.
• If work on the plumbing is required for the proper connection of the
washing machine to the water supply, this must be undertaken by a
registered plumber.
• If work on the electricity supply system is required for the proper
connection of the washing machine to the electricity supply, this
must be undertaken by a registered electrician.
• The washing machine’s mains cable must only be replaced by a
Service Force Engineer
25
Installing the appliance
Transporting the appliance
1
Warning: The washing machine is very heavy. There is a risk of injury.
Exercise care when lifting the appliance.
• Do not lay the washing machine on its front nor on its right side
(as seen from the front). Electrical components may get wet.
• Never transport the appliance without using the transport lock. Only
remove the transport lock when the appliance is in its place of installation. Transporting the appliance without the use of the transport
lock can cause damage to the appliance.
• Never lift the appliance by the door when it is open nor by the plinth.
When using a sack trolley to transport the washing machine:
• Only use the sack trolley on the side of the appliance.
Unpacking
1
The transport safeguard must be removed before putting the appliance
into operation.
Important!
You are advised to keep all the packaging for re-use in case the
machine is to be transported again.
1. After removing all the packaging,
with assistance carefully lay the machine on it’s back to remove the polystyrene base from the bottom.
26
2. Remove the power supply cable and
the draining hose from the hose
holders on the rear of the appliance.
3. With a suitable spanner unscrew and
remove the central rear bolt A. Slide
out the relevant plastic spacer.
4. Unscrew and remove the two large
rear bolts B and the six smaller bolts
C.
27
5. Remove the bracket D.
6. Refit the six smaller bolts C.
7. Open the porthole and remove the
polystyrene block fitted with the adhesive tape on the door seal.
8. Fill the smaller upper hole and the
two large ones with the corresponding plastic plug caps supplied in the
bag containing the instruction
booklet.
Important!
All the different plug caps are supplied with the appliance in the plastic bag containing the instruction
booklet.
28
Connect the water inlet hose as described under the paragraph “Water
inlet”.
Where to install
Important! The washing machine must not be operated in a room
where there is a danger of frost. There is a risk of frost damage or adverse effect on the perfomance of the machine. Frost damage is not
covered under the warranty.
• The surface on which the appliance is to be installed must be firm
and level. Do not install the appliance on carpeted floors or soft floor
coverings.
• The surface on which the appliance is to be installed must be clean
and dry and free from grease, so that the appliance does not slide.
• If the location in which the appliance is to be installed is fitted with
small-format tiles, put a rubber mat (available in the shops) under
the appliance.
Making the appliance level
The four feet of the appliance are
pre-adjusted.
Large degrees of unevenness can be
compensated for by individually adjusting the height adjustable screw
feet.
Use the special spanner supplied to
do this.
Important! Do not use pieces of
wood, cardboard or such like to level out unevenness in the floor, but
adjust the height adjustable screw
feet instead.
29
Electrical Connection
1
1
30
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING – THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should these safety measures
not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used.
Should the plug need to be replaced
for any reason, proceed as described
below.
The wires in the mains lead are
coloured in accordance with the
following code:
Green and Yellow:
Earth
Blue:
Neutral
Brown:
Live
• The wire coloured green and yellow
must be connected to the terminal
marked with the letter “E“ or by the
earth symbol E or coloured green and yellow.
• The wire coloured blue must be connected to the terminal “N“ or
coloured black.
• The wire coloured brown must be connected to the terminal marked
“L“ or coloured red.
• Upon completion there must be no cut, or stray strands of wire
present and the cord clamp must be secure over the outer sheath.
WARNING! A cut off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut off plug is disposed of safely.
Permanent Connection
1
In the case of a permanent connection it is necessary that you install a
double pole switch between the appliance and the electricity supply
(mains), with a minimum gap of 3mm between the switch contacts and
of a type suitable for the required load in compliance with the current
electrical regulations.
The switch must not break the yellow and green earth cable at any
point.
This appliance complies with the requirements laid out in the EEC Directive 76/899.
Voltage 240 V AC: Fuse rating 13amps
See rating plate for further information.
This appliance meets VDE requirements.
Particular regulations of local electricity authorities must be observed.
This appliance conforms to EEC Directive No. 82/499/EWG on radio interference.
WARNING! Repairs to electrical appliances must only be carried out by
trained personnel. Improper repairs may lead to serious risks for the user.
Connecting to the water supply
Permitted water pressure
The water pressure must be at least 1 bar (=10N/cm2 =0.1MPa), and
may be a maximum of 10bar (=100N/cm2 =1MPa).
– If more than 10bar: Connect a pressure reduction valve.
– If less than 1bar: Disconnect the appliance end of the inlet hose from
the solenoid inlet valve and remove the flow meter. (In addition remove the filter using pointed pliers and take out the rubber gasket
behind it.) Refit the filter.
31
Water inlet
Attention!
• An inlet hose is supplied and can be found inside the machine drum.
• Do not use the hose from your previous machine to connect to
the water supply.
• This appliance must be connected to a cold water supply.
1. Open the porthole and extract the inlet hose.
2. Connect the hose with the angled
connection to the machine.
Important!
Do not place the inlet hose downwards. Angle the hose to the left
or right depending on the position
of your water tap.
3. Set the hose correctly by loosening
the ring nut. After positioning the
inlet hose, be sure to tighten the
ring nut again to prevent leaks.
4. Connect the hose to a tap with a
3/4” thread.
Always use the hose supplied with
the appliance.
Water Drainage
The appliance drain hose should hook into a standpipe, the hook in the
drain hose is formed using the plastic “U-Piece“ supplied. The standpipe
should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and
standpipe.
Important! It is essential to lay the drainage hose without kinks.
32
When discharging into a standpipe ensure that the top of the
curve in the hose end is no more
than 90 cm (35.4’’) and no less
than 60 cm (23.6’’) above floor
level.
The upright standpipe should
have a minimum, length of 30 cm
(12’’) from the bottom of the elbow to the top of the pipe (see
diagram). Make sure that it is designed in such a way that the end
of the drain hose cannot be covered with water.
Longer drain hoses are available
in lengths of 2.7 and 4 metres
from your Service Force Centre.
For drainage into an outlet
spigot: If the outlet spigot has not
been used before, remove any blanking plug that may be in place. Push
the drain hose onto the spigot and
secure with a clip if required. Ensure
the drain hose is looped upwards to
prevent waste water from the sink
entering the washing machine.
Important! The end of the drainage hose must not be submerged in the
pumped-out water. Otherwise, the water could be sucked back into the
appliance.
Pumping heights of over 1 metre
The washing machine’s drain pump is able to pump water to a height of
1metre, calculated from the surface on which the appliance is installed.
Important! If pumping height is over 1 metre malfunctions and damage to the appliance may arise.
For pumping heights over 1metre a conversion kit can be obtained.
Please contact Service Force Centre.
33
Guarantee/Customer Service
Great Britain
Standard guarantee conditions
We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or
any part thereof is proved to be defective by reason only of faulty workmanship or materials, we
will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage
on condition that:
• The appliance has been correctly installed and used only on the electricity or gas supply stated
on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer's operating and maintenance instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any
person not authorised by us.
• All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property.
• This guarantee is in addition to your statutory and other legal rights.
• Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available
outside these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those which are subject
to rental agreements.
• Products of AEG manufacture which are not marketed by AEG.
Weitere Kundendienststellen im Ausland
In diesen Ländern gelten die Garantiebedingungen der örtlichen Partner. Diese können dort eingesehen werden.
Further after-sales service agencies overseas
In these countries our AEG-Electrolux agents’ own guarantee conditions are applicable. Please obtain further details direct.
Autres agences étrangères assurant le service après-vente
Dans ces pays, les conditions de garantie des concessionnaires de la région sont valables. Vous pouvez les consulter sur place.
Otros puntos de Postventa en el extranjero
En estos países rigen las condiciones de nuestros representantes locales.
las cuales pueden ser consultadas allí mismo.
Ulteriori uffici del servizio tecnico assistenza clienti all’estero
In questi paesi sono valide le condizioni di garanzia dei partner locali.
Queste condizioni possono essere esaminante sul luogo.
Serviços de assistência técnica no estrangeiro
Nestes países são válidas as condições de garantia dos concessionários
locais, podendo aí ser consultadas.
34
További vevöszolgálati irodák külföldön
Ezekben az országokban a mi AEG-Electrolux vevöszolgálatainknál
saját jótállási feltételek alkalmazhatók. A további adatokat kérjük
közvetlenül szerezzék be.
Servisne službe
Na garancijskem listu boste našli seznam pooblašèenih servisnih
služb AEG-Electrolux.
U.A.E. Abu Dhabi
Universal Trading Company
P.O. Box 43 99
Tel.: 6335331
Service Center 6733974
Jordan
Jordan Household
Supply Co. Ltd.
P.O. Box 3/68
Amman/Tel.: 69 70 50
Malta
ITC
International Trading Company
White House Building
Mountbatte Street
Blata L-Bajda/Tel.: 220644
Egypt
Middle East Commercial
Center
4 Salah El Dein St. - 2nd floor
Heliopolis, Kairo
Egypt
Tel.: 2024181719
Canada
EURO-LINE Appliances
2150 Winston PARK Drive 20
Oakville, Ontario L6H 5V1
Tel.: 905 829 3980
Fax: 905 829 3985
Mauritius
Happy World Centre Ltd.
P.O. 7 54
1 Chausee Street
Port Louis
Tel.: 25355
Australia
The Andi-Co Group
1 Stamford Road
Oakleigh VIC 3166
Tel.: (03) 9569 1255
Fax: (03) 9569 1450
www.andico.com.au
Korea (South)
Core Incorp.
3/F Chewoo Bldg.
200 Nonhyun-Dong
Kangnam-Ku 135-010
Seoul
Telefon 82 2 549 89 61
Namibia
AEG NAMIBIA (PTY)
LIMITED-Jeppe Street
Northern Industrial Area
Windhoek
Tel.: (061) 21-6082/4
Fax: (061) 217838
Bahrain/Arabian Gulf
A.A. Zayani & Sons
P.O. Box 9 32
Bahrain
Tel.: 17311124
Croatia
Electrolux D.O.O.
Suplova 7
10000 Zagreb
Tel.: 1 61 19512
Fax: 1 61 19513
New Zealand
Monaco Corporation Ltd.
10 Rothwell Avenue
Albany - Auckland
4399 Auckland 1
New Zealand
Tel.: 00 64-92 59 11 11
Fax: 00 64-92 59 11 12
Bulgaria
Electrolux Bulgaria E.O.O.D.
91 Levski Blvd.
1000 Sofia
Tel.: 2 806676
Fax. 2 980 5276
Kuwait/Arabian Gulf
Ali Al-Ghanim Est.
P.O. Box 21540 - Safat
Tel.: 4822190
Fax: 4820116
Syria
WATTAR CO.
P.O. Box 36109
Mazzeh - Damascus
Direct Phone: 00963116132649
Fax: 00963116119537
Cyprus
Hadjikyrlakos & Sons Ltd.
Prodromou 121
P.O. Box 21587
Nicosia 1511
Service Telephones:
Nicosia 02 481226
Limassol 05 562182
Larnaca 04 633929
Paphos 06 932 699
Lebanon
Adib & Assaferi
P.O. Box 539
Tripoli
Iran
ARIAN International Development Co.
AEG Showroom
Shariati, Balatar as Safar
Teheran / Iran
Phone No. Showroom:
021 / 285 513 / 4
Phone No. Service:
021 / 312 27 67 / 8
35
36
Estonia
Electrolux Estonia Ltd.
Mustamäe tee 24
EE0006 Tallinn
Tel.: (372) 6 650 090
Fax: (372) 6 650 092
Latvia
Electrolux Latvija Ltd.
Kr.Barona iela 130/2
Riga, LV-1012
Tel.: 371 7313626
Fax: 371 7845954
Poland
Electrolux Poland Sp. zo.o.
ul. Domaniewska 41
02-034 Warszawa
tel.: 022 874 33 33
fax: 022 874 33 00
Hong Kong
Dah Chong Hong Ltd.
20 Kai Cheung Road
Kowloon Bay
Kowloon - Hong Kong
Tel.: 0085222621620
Fax: 0085227550333
Lithuania
Electrolux Lithuania
Verkui 29
2600 Vilnus
Tel.: 372 272 3326
Fax: 372 272 3366
Russia
Electrolux Russia Ltd.
16 Olympiysky prospekt
129090 Moscow
Tel.: (095) 937 7837
Fax: (095) 926 5513
Israel
Evis Ltd.
Tadiran-Ampa Service
10 Gibonay Israel Street
New Industrial Zone
Netanya, 42504
Israel
Malaysia
Arzbergh Engineering
No. 49A/B, Jalan Petaling
Utama 7
4600 Petaling Jaya
Tel.: 3 795 1084
Fax: 3 795 1082
Saudi Arabia
Awad Badi Nahas Est
Shara Siteen
Jeddah 21463
Phone: 6646583
Alia Trading Co
Mecca Road
Riyadh 11491
Phone 4645977
Japan
Electrolux Japan Ltd.
Domestic Appliances
Department
Maruzen Showa Warehouse
Building
Tookai 4-5-12, Ota-ku
143-006 Tokyo
Tel.: 0120-13-7117
Fax: 03-3790-5257
Singapore
Group Pte Ltd.
833 Bukit Timah Road
Unit no. 01-11 Royalville
279887 Singapore
Tel.: 0065 64638484
Fax: 0065 64638488
Slovenia
Electrolux Slovenia D.O.O.
Traska Ul. 132
1000 Ljubljana
Tel.: 61 1234 137
Fax: 61 1234 238
Thailand
Olympia Thai Tower, 444
Rachadapiser Road
Samsennok- Huaykwang
10320 Bangkok
Thailand
Tel.: 006625136111
Fax: 006625136334
Slovakia Rep.
Electrolux Slovakia S.R.O.
Seberiniho 1
821 03 Bratislava
Tel.: 02 4333 4322, 4355
Fax: 02 4333 6976
South Africa
AEG (Pty) Ltd.
55, 12th Road
P.O. Box 1 02 64
Kew/Johannesburg 2000
Tel.: 8069111
Hungary
Electrolux Lehel KFT
Erzsébet Királyné útja 87.
1142 Budapest
Tel.: 00361/467-3200
Czech Rep.
ELECTROLUX DOMÁCå
SPOTØEBIÈE CZ
DIVIZE ELECTROLUX S.R.O.
Customer Centre
Hanusova ul.
140 21 Praha 4
Tel.: 2 6112 6112
Telefax: 2 6112 3504
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user
manual, for the period specified in the appliance guarantee or otherwise by law. If you move
from one of these countries to another of the countries listed below the appliance guarantee
will move with you subject to the following qualifications:• The appliance guarantee starts from the date you first purchased the appliance which will be
evidenced by production of a valid purchase document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and parts as
exists in your new country of residence for this particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the appliance and cannot be
transferred to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is
only used within the home, i.e. is not used for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in force within your new
country of residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
www.electrolux.com
p
t
b
Albania
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/
Belgien
+32 2 363 04 44
Bergensesteenweg 719, 1502 Lembeek
Èeská republika
+420 2 61 12 61 12
Budìjovická 3, Praha 4, 140 21
Danmark
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
Deutschland
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
Eesti
+37 2 66 50 030
Mustamäe tee 24, 10621 Tallinn
España
+34 902 11 63 88
Carretera M-300, Km. 29,900
Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire
LU4 9QQ
Hellas
+30 23 10 56 19 70
4 Limnou Str., 54627 Thessaloniki
Hrvatska
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
Ireland
+353 1 40 90 753
Long Mile Road Dublin 12
Italia
+39 (0) 434 558500
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Latvija
+37 17 84 59 34
Kr. Barona iela 130/2, LV-1012, Riga
Lietuva
+370 5 2780609
Verkių 29, LT09108 Vilnius
Luxembourg
+35 2 42 43 13 01
Rue de Bitbourg, 7, L-1273 Hamm
37
38
p
t
b
Magyarország
+36 1 252 1773
H-1142 Budapest XIV,
Erzsébet királyné útja 87
Nederland
+31 17 24 68 300
Vennootsweg 1, 2404 CG Alphen aan den Rijn
Norge
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
Österreich
+43 18 66 400
Herziggasse 9, 1230 Wien
Polska
+48 22 43 47 300
ul. Kolejowa 5/7, Warsaw
Portugal
+35 12 14 40 39 39
Quinta da Fonte - Edificio Gonçalves
Zarco - Q 35
2774 - 518 Paço de Arcos
Romania
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671 RO
Schweiz/Suisse/
Svizzera
+41 62 88 99 111
Industriestrasse 10, CH-5506 Mägenwil
Slovenija
+38 61 24 25 731
Electrolux Ljubljana, d.o.o.
Tržaška 132, 1000 Ljubljana
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux
Domáce spotrebièe SK, Seberíniho 1,
821 03 Bratislava
Suomi
+35 8 26 22 33 00
Konepajanranta 4, 28100 Pori
Sverige
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143,
S-105 45 Stockholm
Türkiye
+90 21 22 93 10 25
Tarlabaþý caddesi no : 35 Taksim
Istanbul
Ðîññèÿ
+7 495 9377837
129090 Ìîñêâà, Îëèìïèéñêèé
ïðîñïåêò, 16, ÁÖ „Îëèìïèê“
Service and Spare Parts
If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to the Service Force
Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the website at
www. serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details
under the heading „What to do if...“
When you contact the Service Force Centre you will need to give the
following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating
plate)
5. The purchase date.
Please note that a valid purchase receipt or guarantee documentation is
required for in-guarantee service
calls.
Customer Care
For general enquiries concerning
your AEG appliance, or for further
information on AEG products please
contact our Customer Care Department by letter or telephone at the
address below or visit our website at www.aeg.co.uk.
Customer Care Department For Customer Service in the Republic
Major Appliances
of Ireland please contact us at the adAEG Domestic Appliances
dress below:
Addington Way
AEG/ Electrolux Group (Ire) Ltd
Luton
Long Mile Road/ Dublin 12
Bedfordshire, LU4 9QQ
Republic of Ireland
Tel: 08705 350350 (*)
Tel: +353 (0) 1 4090754
Email: service.eid@electrolux.ie
(*) Calls may be recorded for training purposes
39
www.electrolux.com
www.aeg-electrolux.co.uk
132 978 980-01-160806-01
Subject to change without notice
Download PDF

advertising