Operating instructions | Electrolux 54750 Dishwasher User Manual

152955 17/2en
13-10-2005
15:59
Pagina 1
FAVORIT 54750
Dishwasher
Instruction book
PERFEKT IN FORM UND FUNKTION
152955 17/2en
13-10-2005
15:59
Pagina 2
Dear customer,
Please read this User Information carefully and keep it to refer to at a
later date.
Pass it on to any subsequent owner of the appliance.
The following symbols are used in the text:
Safety instructions
Warning! Notes that concern your personal safety.
Attention! Notes that show how to avoid damage to the appliance.
Useful tips and hints
Environmental information
Your dishwasher has the new washing system ”IMPULSE WASHING”.
With this dishwashing system the motor speed and spray pressure
are varied during the wash cycle to achieve better cleaning of the
dishes. It is for this reason that the noise level varies during the
dishwashing cycle.
2
152955 17/2en
13-10-2005
15:59
Pagina 3
Contents
CONTENTS
Operating instructions
Safety instructions
Disposal
Economical and ecological dishwashing
Description of the appliance
The control panel
Prior to using for the first time
The water softener
Filling with dishwasher salt
Rinse aid
In daily use
Loading cutlery and dishes
The lower basket
The cutlery basket
The upper basket
Adjusting the height of the upper basket
Use of detergent
Different kinds of detergent
Washing programmes
Starting a washing programme
Maintenance and cleaning
Cleaning the filters
Something not working
Service
Guarantee Conditions
Technical specifications
Installation instructions
Fitting under a counter
Levelling
Water supply connections
Water inlet hose with safety valve
Water outlet hose connection
Electrical connection
Hints for test centres
4
4
6
6
7
8
12
12
15
16
18
18
19
20
21
22
23
24
26
28
31
31
34
37
40
42
43
43
43
44
45
46
47
49
3
152955 17/2en
13-10-2005
15:59
Pagina 4
Operating instructions
OPERATING INSTRUCTIONS
Safety instructions
The safety of AEG electrical appliances conforms to accepted rules of
technology and the Appliance Safety Act. We as manufacturers,
however, see ourselves as being obliged to familiarise you with the
following safety instructions.
It is most important that this instruction book should be retained
with the appliance for future reference. Should the appliance be
sold or transferred to another owner, or should you move house
and leave the appliance, always ensure that the book is left with
the appliance in order that the new owner can get to know the
functioning of the appliance and the relevant safety information.
This information has been provided in the interest of your safety.
You MUST read it carefully before installing or using the
appliance.
If you are unsure about any aspect of the information in this
book, please contact our customer care department on 08705 950
950
Installation
●
●
●
●
●
Check your dishwasher for any transport damage. Never connect a
damaged machine. If your dishwasher is damaged, you should
contact your supplier.
For safety reasons it is dangerous to alter the specifications or
attempt to modify this product in any way.
Any electrical and plumbing work required to install this appliance
should be carried out by a qualified and competent person.
Care must be taken to ensure that the appliance does not stand on
the electrical supply cable.
The sides of the dishwasher must never be drilled to prevent
damage to hydraulic components.
Child safety
●
●
4
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the controls or play
with the product.
152955 17/2en
13-10-2005
15:59
Pagina 5
Operating instructions
●
●
●
Packaging parts may be dangerous for children, who could even be
suffocated! You should therefore keep all packaging well away
from children.
The water in your dishwasher is not for drinking. Detergent residues
may still be present in your machine. Keep children well away from
your dishwasher when the door is open.
Keep all detergents in a safe place out of children’s reach.
Your dishwasher in day-to-day use
●
●
●
●
●
●
●
●
●
●
●
Items that are contaminated by petrol, paint, steel or iron debris,
corrosive, acidic or alkaline chemicals must not be washed in this
dishwasher.
Under no circumstances should you open the door whilst the
appliance is in operation, especially during the washing phase, hot
water may escape. However, if the door is opened, a safety device
ensures that the machine stops.
Only use products (detergent, salt and rinse aid) specifically
designed for use in dishwashers.
Long bladed knives stored in an upright position are a potential
hazard.
Long and/or sharp items of cutlery such as carving knives must be
positioned horizontally in the upper basket.
Ensure that the door of the dishwasher is always closed when it is
not being loaded or unloaded. In this way you will avoid anybody
tripping over the open door and hurting themselves.
When finishing loading or unloading close the door, as an open
door can be a hazard.
Do not sit or stand on the open door.
Isolate the appliance from the power supply and turn off the water
supply after use.
This product should be serviced by an authorised service engineer,
and only genuine spare parts should be used.
Under no circumstances should you attempt to repair the machine
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local Service Force
Centre. Always insist on genuine spare parts.
5
152955 17/2en
13-10-2005
15:59
Pagina 6
Operating instructions
Disposal
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with standard international abbreviations:
>PE<
for polyethylene, e.g. sheet wrapping material.
>PS<
for polystyrene, e.g. padding material (always CFC-free).
>POM<
for polyoxymethylene, e.g. plastic clips.
Cardboard packaging is manufactured from recycled paper and should
be deposited in the waste paper collection for recycling.
As and when you cease to use your dishwasher and withdraw it from
service, your should render it unserviceable before having it disposed of.
Warning! Children at play could lock themselves in your dishwasher or
otherwise endanger their lives. Therefore cut off the power supply
cable and make the door closing device unusable to prevent children
from being trapped inside.
For the disposing of the appliance please take it to a recycling centre
or to your dealer who may, for a small contribution to the costs,
dispose it for you.
The symbol
on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please
contact your local city office, your household waste disposal service or
the shop where you purchased the product.
Economical and ecological dishwashing
●
●
●
●
6
Ensure that the water softener is correctly adjusted.
Do not pre-wash under running water.
Select the wash programme to suit the nature and degree of the
soiling on the dishes.
Do not use more detergent, dishwasher salt and rinse aid than is
recommended in these operating instructions and by the
manufacturer of the respective product.
152955 17/2en
13-10-2005
15:59
Pagina 7
Operating instructions
Description of the appliance
IN154
1. Upper basket stop
7. Rinse aid dispenser
2. Water hardness switch
8. Filters
3. Salt container
9. Lower spray arm
4. Detergent dispenser
10. Upper spray arm
5. Control panel
11. Upper basket
6. Rating plate
12. Worktop
7
152955 17/2en
13-10-2005
15:59
Pagina 8
Operating instructions
The control panel
Function buttons
Indicator lights
1 2 3 4
On/Off button
Door handle
Programme selection
buttons
“Delay start”
button
Function buttons: in addition to the dishwashing programme
selected, the following functions can also be set with the help of these
buttons:
- the setting of the water softener,
- activation/deactivation of the rinse aid dispenser,
- activation/deactivation of the 3 in 1 function,
- the cancelling of a programme in progress.
Programme selection buttons: the selection of a washing
programme occurs by pressing one of these buttons (see "Washing
programmes" chart).
"Delay start" button: this option allows the start of the programme
to be delayed by 3, 6, or 9 hours.
Indicator lights: have the following meanings:
Salt refilling indicator light, illuminates when the salt has
run out
Rinse aid refilling indicator light, illuminates when the rinse
aid has run out
The salt and rinse aid indicator lights are never illuminated while a
washing programme is running even if filling with salt and rinse aid is
necessary.
8
152955 17/2en
13-10-2005
15:59
Pagina 9
Operating instructions
Programme in progress: illuminates when a washing
programme has been set and remains illuminated for all the
duration of the washing programme.
Turns off when the washing programme has ended.
When delay start has been set, this indicator light turns off
and will come on again once the countdown has elapsed and
the washing programme has started.
End of programme: illuminates when the washing
programme has ended, it also has added functions of visual
signalling as:
- the setting of the water softener,
- activation/deactivation of the rinse aid dispenser,
- intervention of an alarm due to the malfunction of the
machine.
3 IN 1 3 in 1 function: indicates the activation/deactivation of the
3 in 1 function (see “3 in 1 function”).
"3 in 1" function
This appliance is equipped with the 3 in 1 function, that allows the
use of the "3 in 1" combi detergent tablets.
This function can be selected with all washing programmes.
With the selection of this function the inflow of rinse aid and salt
from each respective supply container is automatically deactivated and
also the indicator lights for salt and rinse aid are deactivated.
Select the 3 in 1 function before the set of a washing programme.
Once selected this function (indicator light illuminated) it will remain
active also for the following washing programmes.
With the use of 3 in 1 function, the cycle durations given in the
“Washing programmes” chart may change.
NOTE: Once the programme is running, the 3 in 1 function can NO
longer be changed. If you want to exclude the 3 in 1 function you
have to cancel the programme setting (see chapter "Starting a washing
programme" - "Cancel a washing programme in progress") and then
deactivate the 3 in 1 function.
In this case you have to set a washing programme (and eventual
options) again.
9
152955 17/2en
13-10-2005
15:59
Pagina 10
Operating instructions
Activation/deactivation of the 3 in 1 function
(The dishwasher must be switched off)
1. Press the On/Off button. The indicator lights of the programme
selection buttons will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated this means that a washing programme is set.
The programme must be cancelled: press simultaneously
function buttons 2 and 3 for about 2 seconds, the indicator
light of the set programme button starts flashing. After about 2
seconds the indicator lights of all the programme selection buttons
will illuminate, this means that the set washing programme has
been cancelled and the machine is now in setting mode.
2. Press simultaneously function buttons 2 and 3, until the indicator
lights of function buttons 1, 2, 3 and 4 start flashing.
3. Press function button 4, the indicator lights of function buttons 1,
2 and 3 turn off while the indicator light of function button 4
goes on flashing.
4. Press function button 4 again, the “3 in 1” indicator light
illuminates, indicating that the “3 in 1 function” is active.
To deactivate the function press function button 4 again, the
indicator light turns off.
3 in 1 function active
indicator light on
3 in 1 function not active
indicator light off
5. To memorise the operation, switch off the dishwasher by pressing
the On/Off button or wait about 60 seconds after which the
dishwasher will automatically return to setting mode.
10
152955 17/2en
13-10-2005
15:59
Pagina 11
Operating instructions
NOTE: if the drying results are not satisfactory it is possible to activate
only the rinse aid dispenser.
The activation/deactivation of the rinse aid dispenser can only be
possible with the 3 in 1 function active.
Activation/deactivation of the rinse aid dispenser
(The dishwasher must be switched off)
When the rinse aid dispenser has been activated, the rinse aid
indicator light on the control panel is automatically activated.
1. Press the On/Off button. The indicator lights of the programme
selection buttons will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated this means that a washing programme is set.
The programme must be cancelled: press simultaneously
function buttons 2 and 3 for about 2 seconds, the indicator
light of the set programme button starts flashing. After about 2
seconds the indicator lights of all the programme selection buttons
will illuminate, this means that the set washing programme has
been cancelled and the machine is now in setting mode.
2. Press simultaneously function buttons 2 and 3, until the indicator
lights of function buttons 1, 2, 3 and 4 start flashing.
3. Press function button 2, the indicator lights of function buttons 1,
3 and 4 turn off while the indicator light of function button 2 goes
on flashing.
4. To activate the rinse aid dispenser, press function button 2 again,
the indicator light end of programme illuminates, indicating that
the rinse aid dispenser has been activated.
5. To memorise the operation, switch off the dishwasher by pressing
the On/Off button or wait about 60 seconds after which the
dishwasher will automatically return to setting mode.
To deactivate the rinse aid dispenser again, follow the above
instructions until the indicator light end of programme turns off.
11
152955 17/2en
13-10-2005
15:59
Pagina 12
Operating instructions
Prior to using for the first time
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply with the
installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill with
dishwasher salt
5. Fill the rinse aid dispenser.
Note:
If you want to use the "3 in 1" combi detergents, read carefully
the informations given in "Different kinds of detergents".
The water softener
The dishwasher is equipped with a water softener designed to remove
minerals and salts from the water supply, which would have a
detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your
water is.
Water hardness is measured in equivalent scales, German degrees (°dH),
French degrees (°TH) and mmol/l (millimol per litre).
The softener should be adjusted according to the hardness of the water
in your area. Your local Water Authority can advise you on the
hardness of the water in your area.
The water softener must be set in both ways: manually, using the water
hardness dial and electronically, using the function buttons on the
control panel.
12
152955 17/2en
13-10-2005
15:59
Pagina 13
Operating instructions
a) Setting manually
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness dial to position 1 or 2 (see table).
4. Replace the lower basket.
The dishwasher is factory set at
position 2.
Adjusting the water
hardness setting
Water hardness
mmol/l
°dH
°TH
(german
degrees)
(french
degrees)
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
91 - 125
76 - 90
65 - 75
51 - 64
40 - 50
9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
IV
19 - 22
15 - 18
33 - 39
26 - 32
3,3 - 3,9
2,6 - 3,2
11 - 14
19 - 25
4 - 10
<4
(millimol per litre,
Range
international unit for
the hardness of water)
Manually
Electronically
Number of
flashes of the
“end of
programme”
indicator light
10
9
8
7
6
10
9
8
7
6
III
5
4
5
4
1,9 - 2,5
II
3
3
7 - 18
0,7 - 1,8
I/II
2
2
<7
< 0,7
I
2
1
1
no salt
necessary
1
13
152955 17/2en
13-10-2005
15:59
Pagina 14
Operating instructions
b) Setting electronically
(The dishwasher must be switched off)
NOTE: the electronic setting of the water softener is possible ONLY
with the 3 in 1 function deactivated.
The dishwasher is factory set at level 5.
1. Press the On/Off button. The indicator lights of the programme
selection buttons will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated this means that a washing programme is set.
The programme must be cancelled: press simultaneously
function buttons 2 and 3 for about 2 seconds, the indicator
light of the set programme button starts flashing. After about 2
seconds the indicator lights of all the programme selection
buttons will illuminate, this means that the set washing
programme has been cancelled and the machine is now in setting
mode.
2. Press simultaneously function buttons 2 and 3, until the indicator
lights of function buttons 1, 2, 3 and 4 start flashing.
3. Press function button 1, the indicator lights of function buttons 2,
3 and 4 turn off while the indicator light of the button 1 goes on
flashing, at the same time the indicator light end of programme
starts to flash.
The current level is indicated by the number of flashes of the
indicator light end of programme (see chart).
Example:
5 flashes = level 5.
4. To change the level, press function button 1. Each time the button
is pressed the level changes. (For the selection of the new level see
the chart).
Examples:
if the current level is 5, by pressing function button 1 once,
level 6 is selected.
if the current level is 10, by pressing function button 1 once,
level 1 is selected.
5. To memorise the operation, switch off the dishwasher by pressing
the On/Off button or wait about 60 seconds after which the
dishwasher will automatically return to setting mode.
14
152955 17/2en
13-10-2005
15:59
Pagina 15
Operating instructions
Filling with dishwasher salt
Only use salt specifically designed for use in dishwashers.
All other types of salt not specifically designed for use in a
dishwasher, especially table salt, will damage the water softener.
Only fill with salt just before starting one of the complete washing
programmes.
This will prevent any grains of salt or salty water, which may have
been spilt, remaining on the bottom of the machine for any period
of time, which may cause corrosion.
To fill:
1. Open the door, remove the lower basket and unscrew the cap of
the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary only
before filling with salt for the first time).
3. Using the funnel provided, pour in the
salt until the container is full.
4. Replace the cap making sure that
there is no trace of salt on the screw
thread or on the gasket.
5. Replace on the cap tightly turning it
clockwise until it stops with a click.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel which
comes on when the salt has finished.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been replenished,
assuming the dishwasher remains switched on. If you are using
salts that take longer to dissolve then this can take longer. The
function of the machine is not affected.
Do not worry if water over flows from the unit when filling with salt,
this is quite normal.
15
152955 17/2en
13-10-2005
15:59
Pagina 16
Operating instructions
Rinse aid
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying.
The dispenser, which is positioned inside the door, holds about 110 ml
of rinse aid, which is sufficient for 16 - 40 dishwashing programmes,
depending upon the dosage setting.
Filling with rinse aid
1. Open the container by pressing the release button (A).
2. Add the rinse aid until the container is completely full. The
maximum level for filling is indicated by “max”.
Ensure that the lid is closed after every refill.
Clean up any rinse aid spilt during filling with an absorbent cloth
to avoid excess foaming during the next wash.
Only use branded rinse aid for dishwashers. Never fill the rinse aid
dispenser with any other substances (e.g. dishwasher cleaning
agent, liquid detergent). This would damage the appliance.
16
152955 17/2en
13-10-2005
15:59
Pagina 17
Operating instructions
Adjusting the dose
According to the finish and drying results obtained, adjust the dose of
rinse aid by means of the 6 position selector (position 1 minimum
dosage, position 6 maximum dosage).
The dose is factory set in position 4.
Increase the dose if there are drops of
water or lime spots on the dishes after
washing.
Reduce it if there are sticky whitish
streaks on the dishes or a bluish film on
glassware or knife blades.
Top up the rinse aid when the indicator light on the control panel
illuminates.
17
152955 17/2en
13-10-2005
15:59
Pagina 18
Operating instructions
In daily use
• Check if it’s necessary to refill with dishwasher salt or rinse aid.
• Load cutlery and dishes into the dishwasher.
• Fill with dishwasher detergent.
• Select a wash programme suitable for the cutlery and dishes.
• Start the wash programme.
Loading cutlery and dishes
Sponges, household cloths and any object that can absorb water
may not be washed in the dishwasher.
• Before loading the dishes, you should:
- Remove large left-overs.
- Soften remnants of burnt food in pans.
• When loading the dishes and cutlery, please note:
- Dishes and cutlery must not impede the rotation of the spray arms.
- Load hollow items such as cups, glasses, pans etc, with the opening
downwards so that water cannot collect in the container or a
deep base.
- Dishes and items of cutlery must not lie inside one another, or
cover each other.
- To avoid damage to glasses, they must not touch.
- Lay small objects in the cutlery basket.
• Plastic items and pans with teflon have a tendency to retain
water drops; these items will not dry as well as porcelain and steel
items.
18
152955 17/2en
13-10-2005
15:59
Pagina 19
Operating instructions
For washing in the dishwasher the following cutlery/dishes
are not suitable:
• Cutlery with wooden, horn, china or
mother-of-pearl handles
are of limited suitability:
• Plastic items that are not heat resistant
• Only wash stoneware in the dishwasher if it
is specifically marked as being dishwashersafe by the manufacturer.
• Older cutlery with glued parts that is not
temperature resistant
• Glazed patterns may fade if machine
washed frequently.
• Bonded cutlery items or dishes
• Silver and aluminium parts have a tendency
to discolour during washing. Residues, e.g.
egg white, egg yolk and mustard often
cause discolouring and staining on silver.
Therefore always clean left-overs from silver
immediately, if it is not to be washed
straight after use.
• Pewter or copper items
• Lead crystal glass
• Steel items subject to rusting
• Wooden platters
• Items made from synthetic fibres
• Some types of glass can become dull after a
large number of washes.
Open the door and slide out the baskets to load the dishes.
The lower basket
The lower basket is designed to take saucepans, lids, plates, salad
bowls, cutlery etc.
Serving dishes and large lids should be arranged around the edge of
the basket, ensuring that the spray arms can turn freely.
19
152955 17/2en
13-10-2005
15:59
Pagina 20
Operating instructions
The cutlery basket
Long bladed knives stored in an upright position are a potential
hazard.
Long and/or sharp items of cutlery such as carving knives must be
positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as knives.
Forks and spoons should be placed in the removable cutlery basket
with the handles facing downwards and the knives with their handles
facing upwards.
If the handles protrude from the bottom of the basket, obstructing the
lower spray arm, load the cutlery with the handles facing upwards.
Mix spoons with other cutlery to prevent them from sticking together.
To unload your dishwasher more easily, you can take the cutlery basket
out of the lower basket and unfold it. This makes it easier to remove
small pieces of cutlery.
Important note! To prevent the full cutlery basket from inadvertently
unfolding when being taken out, place your hand right round the twopiece handle and hold it firmly.
1. Place the cutlery basket on a firm support (table, worktop)
and unfold both handle parts.
2. After unfolding, fold back both handle parts.
20
152955 17/2en
13-10-2005
15:59
Pagina 21
Operating instructions
The upper basket
The upper basket is designed for plates (dessert plates, saucers, dinner
plates of up to 24 cm in diameter), salad bowls, cups and glasses.
Arrange items on and underneath the cup racks so that water can
reach all surfaces.
Glasses with long stems can be placed upside down in the cup racks.
For taller items, the cup racks can be folded upwards.
Light items (plastic bowls etc.) must be loaded in the upper basket and
arranged so they do not move.
Before closing the door, ensure that the spray arms can rotate
freely.
21
152955 17/2en
13-10-2005
15:59
Pagina 22
Operating instructions
Adjusting the height of the upper basket
If washing very large plates you can load them in the lower basket
after moving the upper basket to the higher position.
Maximum height of the dishes in:
upper basket
lower basket
With upper basket raised
20 cm
31 cm
With upper basket lowered
24 cm
27 cm
To move to the higher position proceed as follows:
1. Move the front runner stops (A) of the upper basket outwards
and slide the basket out.
2. Refit the basket in the higher position and replace the stops (A)
in their original position.
When the basket is in the higher
position you will not be able to use
the cup rack(s).
After loading your machine always close the door, as an open door
can be a hazard.
22
152955 17/2en
13-10-2005
15:59
Pagina 23
Operating instructions
Use of detergent
Only use detergents specifically designed for use in dishwashers.
We recommend the use of Finish detergents.
Using no more than the correct amount of detergent contributes
to reducing pollution.
Please observe the manufacturer’s dosing and storage
recommendations as stated on the detergent packaging.
Fill with detergent
1. If the lid is closed: press release button (1). The lid springs open.
2. Fill the detergent dispenser (2) with detergent.
The marking indicates the dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent
3. All programmes with prewash need an additional detergent dose
(5/10 g) that must be placed in the prewash detergent chamber (3).
This detergent will take effect during the prewash phase.
4. Close the lid and press until it locks in place.
23
152955 17/2en
13-10-2005
15:59
Pagina 24
Operating instructions
Different kinds of detergent
Detergent tablets
Detergent tablets from different manufactures dissolve at different
rates. For this reason, some detergent tablets do not attain their full
cleaning power during short washing programmes. Therefore please
use long washing programmes when using detergent tablets, to ensure
the complete removal of detergent residuals.
Concentrated detergent
Modern detergents for dishwashers are almost exclusively low-alkaline
concentrated detergents with natural enzymes in tablet form.
Using 50°C washing programmes in conjunction with these
concentrated detergents reduces pollution and is good for your dishes,
as these washing programmes are specially matched to the dirtdissolving properties of the enzymes in concentrated detergents. It is
for this reason that using 50°C washing programmes in conjunction
with concentrated detergents can achieve the same cleaning results
that can otherwise only be achieved using 65°C washing programmes.
EASY
POURING
PACK
N EW
ION
DOUBLE ACT
FOR A
BRILLIANT
RILLIANT
SHINE
L I Q U I D
G E L
P O W D E R
RINSE
C O N C E N T R AT E D D I S H WA S H E R D E T E R G E N T
24
152955 17/2en
13-10-2005
15:59
Pagina 25
Operating instructions
Use of "3 in 1" combi detergents
These products are detergents with a combined cleaning, rinsing and
salt function.
1. Check whether these detergents are suitable for your water
hardness. Follow the manufacturers instructions.
2. Set the "3 in 1" function.
3. Before the start of the washing programme put the "3 in 1"
detergent in the detergent dispenser.
NOTE: If the drying results are not satisfactory we recommend that
you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Activate the rinse aid dispenser and set the rinse aid dosage to
position 2.
If you decide to turn back to the use of the standard detergent
system we advise that you:
● Deactivate the "3 in 1" function.
●
Fill up the dispensers for salt and rinse aid again.
●
Adjust the water hardness setting to the highest setting perform up
to 3 normal washing programmes without loading any dishes.
Adjust the water hardness setting according to the hardness of the
water in your area.
Adjust the rinse aid dosage.
●
●
NOTE: When using 4 in 1 detergents that integrate also anti-glass
corrosion agent into "3 in 1" formula, please follow the same
instruction as given for "3 in 1" detergents above.
25
152955 17/2en
13-10-2005
15:59
Pagina 26
Operating instructions
Washing programmes
Water (litres)
Energy (kWh)
Drying
Final rinse
• • • • •
80 0,8 12
105 1,2 21
Fresh soil
- • - • -
25 0,7
30 0,8
Crockery, cutlery,
pots and pans
Heavy soil
• • •
• • 2x
115 1,6 19
125 1,8 21
Crockery and
cutlery
Normal soil
• • • • •
160 0,75 12
170 0,8 13
Any. Partial load
(to be completed
later in the day).
This programme does not
require the use of
detergent.
• - - - -
12 0,1
AUTOMATIC
Crockery, cutlery,
pots and pans
Normal / light soil
30 MIN. 1
Crockery and
cutlery
INTENSIV
CARE 70°
ECO 50° 2
(Rinse and Hold)
Intermediate
Degree of
soil
Main wash
Type of
load
Pre-rinse
Programme
Duration (minutes)
Consumption
values3
Cycle
description
1/2x
7
8
3
4
(1) Ideal for washing crockery and cutlery of breakfast and dinner (fresh soil).
This is the perfect daily programme, made to meet the needs of a family of 4 persons who
only wish to load breakfast and dinner crockery and cutlery.
(2) Testing programme for EN 50242 (see "Hints for Test Centres). This programme, developed
for the use of detergents with enzymes, allows you to achieve, with reduced consumption
of energy the same cleaning results that would otherwise be obtained only with the 65°C
programmes and conventional detergents. To compensate the lower temperature, the
duration of washing and drying have been extended.
(3) The consumption values are intended as a guide and depends on the pressure and the
temperature of the water and also by the variations of the power supply.
26
152955 17/2en
13-10-2005
15:59
Pagina 27
Operating instructions
"AUTOMATIC" washing programme
During the "AUTOMATIC" washing programme the amount of soil on the dishes is determined
by how cloudy the water is.
If the appliance is partially loaded and the dishes lightly soiled, the "prewash", "main wash",
and "rinse" phases of the programme are shorter and the water consumption level is lower.
If the appliance is fully loaded and the dishes heavily soiled, the "prewash"", main wash", and
"rinse" phases of the programme are longer and the water consumption level is higher.
For this reason the programme duration, water and energy consumption levels can vary within
the stated range for AUTOMATIC programme (see "Washing programmes chart").
During the "AUTOMATIC" programme the temperature of the main wash water is also
automatically adjusted between 50°C and 65°C depending on the amount of soil on the
dishes.
27
152955 17/2en
13-10-2005
15:59
Pagina 28
Operating instructions
Starting a washing programme
1. Check that the baskets have been loaded
correctly and that the spray arms can rotate
freely
2. Turn on the water tap
3. Close the dishwasher door
4. Press the On/Off button
The indicator lights of the programme selection buttons illuminate.
5. Setting and starting the programme
To select a programme, press the button of the programme you
wish to select (see "Washing programmes" chart).
The corresponding indicator light remains illuminated while the
other programme buttons indicator lights turn off.
The programme in progress indicator light will illuminate.
After about 3 seconds from the last pressure of a button the
programme starts automatically.
The programme in progress indicator light remains illuminated.
Setting and starting the programme with “delay start”
Set the delay start before selecting a washing programme.
Press the "delay start" button until the indicator light
corresponding to the chosen hours flashes (3h, 6h or 9h).
Press the button corresponding to the required programme (see
“Washing programmes” chart).
After about 3 seconds from the last pressure of a button the
countdown starts automatically.
The countdown will decrease with steps of 3 hours.
The opening of the door will not modify or interrupt the
countdown.
Once the delay start has elapsed the programme will start
automatically.
28
152955 17/2en
13-10-2005
15:59
Pagina 29
Operating instructions
Note: With the delay start function set, the programme in
progress indicator light is off. Once the countdown of the delay
start has elapsed, the washing programme will start automatically
and the programme in progress indicator light will illuminate.
Note: it is possible to select a washing programme and the delay
start also with the door slightly opened. In this case the start of
the programme or of the countdown will occur after the closure of
the door. Until that moment it is possible to modify the set made.
6. To interrupt or cancel a washing programme
in progress
Interrupt or cancel a washing programme in progress
ONLY if it’s absolutely necessary
Attention! Hot steam may escape when the door is opened.
Open the door carefully.
Interrupt a washing programme in progress
a) Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point at
which it was interrupted.
b) Press the On/Off button (in this case all the indicator light turn
off). Press the On/Off button again; the programme will start
from the point at which it was interrupted.
Cancel a washing programme in progress
To cancel a washing programme in progress, press simultaneously
function buttons 2 and 3 for about 2 seconds, the indicator light
of the button corresponding to the running programme starts
flashing.
After about 2 seconds the indicator lights of all the programme
selection buttons will illuminate, this means that the running
programme has been cancelled and that the machine has returned
to setting mode.
If a new washing programme is to be selected, check that there
is detergent in the detergent dispenser.
29
152955 17/2en
13-10-2005
15:59
Pagina 30
Operating instructions
7. Cancelling the “delay start”
It is possible to cancel a countdown in progress or before it starts,
simply pressing the delay start button until the indicator lights
corresponding to delay start hours (3h, 6h or 9h) turn off.
In this case the selected washing programme will start
automatically after a 3 seconds.
8. End of the washing programme
The dishwasher will automatically stop and the programme in
progress indicator light turns off.
The end of programme indicator light will illuminate.
The indicator light of the programme just ended will remain on.
The dishwasher’s drying system is provided with a device that
allows air to circulate inside the dishwasher to prevent residual
steam recondensing on the dishes as water droplets.
Once the washing programme has ended this device operates
intermittently for other 20 minutes, as long as the dishwasher
is switched on.
If the On/Off button is pressed or the door is opened during
these 20 minutes, the device will be automatically cancelled.
Switch off the dishwasher by pressing the On/Off button.
Open the dishwasher’s door, leave it ajar and wait a few minutes
before removing the dishes; in this way they will be cooler and the
drying will be improved.
9. Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should therefore be
allowed to cool down before removing from the appliance.
Empty the lower basket first and then the upper one; this will
avoid water dripping from the upper basket onto the dishes in the
lower one.
Water may appear on the sides and the door of the dishwasher as
the stainless steel will eventually become cooler then the dishes.
When the washing programme has finished, it is recommended
that the dishwasher is unplugged and the water tap turned off.
30
152955 17/2en
13-10-2005
15:59
Pagina 31
Operating instructions
Maintenance and cleaning
Clean the external surfaces of the machine and control panel with a
damp soft cloth. If necessary use only neutral detergents. Never use
abrasive products, scouring pads or solvent (acetone, trichloroethylene
etc....).
Ensure that the seals around the door, the detergent and rinse aid
dispensers are cleaned regularly with a damp cloth.
We recommend the use of Finish Dishwasher Cleaner every 3 months
or run a 65°C wash programme without dishes using detergent.
Regular use of Finish Dishwasher Cleaner cleans inaccessible parts,
eliminates unpleasant food odours and helps prevent the build-up of
limescale.
Cleaning the filters
The filters must be checked and cleaned from time to time.
Dirty filters will degrade the washing result.
1. Open the door, remove the lower basket.
2. The dishwasher filter system comprises a coarse filter (A), a
microfilter (B) and a flat filter (C).
Unlock the filter system using the handle on the microfilter, and
remove.
3. Turn the handle about 1/4 a turn anticlockwise and remove.
31
152955 17/2en
13-10-2005
15:59
Pagina 32
Operating instructions
4. Take hold of the coarse filter (A) by the handle with the hole and
remove from the microfilter (B).
5. Clean all filters thoroughly under running water.
6. Remove the flat filter (C) from the base of the washing
compartment and clean both faces thoroughly.
7. Put the flat filter (C) back in the base of the washing compartment.
8. Place the coarse filter (A) in the microfilter (B) and press together.
9. Put the filter combination in place and lock by turning the handle
clockwise to the stop. During this process ensure that the flat filter
does not protrude above the base of the washing compartment.
Attention!
Under no circumstances may the dishwasher be used without filters.
Incorrect repositioning and fitting of the filters will produce poor
washing results.
NEVER try to remove the upper
spray arm.
If residues of soil have clogged the
holes in the upper spray arm,
remove them with a cocktail stick.
32
152955 17/2en
13-10-2005
15:59
Pagina 33
Operating instructions
Prolonged periods of non-operation
If you are not using the machine for any period of time you are
advised to:
1. Unplug the appliance and then turn off the water.
2. Leave the door ajar to prevent the formation of any unpleasant
smells.
3. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where the temperature is
below 0°C. If this is unavoidable, empty the machine, close the
appliance door, disconnect the water inlet pipe and empty it.
Moving the machine
If you have to move the machine (moving house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
33
152955 17/2en
13-10-2005
15:59
Pagina 34
Operating instructions
Something not working
Certain problems are due to the lack of simple maintenance or
oversights, which can be solved with the help of the instructions given
here, without calling out an engineer.
Important: If you call out an engineer to a fault listed below or to
repair a fault caused by incorrect use or installation a charge will be
made, even if the appliance is in guarantee.
...a flashing fault code appears
The dishwasher will not start or stops during operation.
The intervention of an alarm is indicated by:
- the continuous flashing of the indicator light of the running
programme,
- a combination of flashing and pauses of the end of programme
indicator light (as described in the chart).
Open the door and carry out the following suggested corrective
actions.
Fault code / Malfunction
- continuous flashing of
the indicator light of
the running programme
- 1 flash of the indicator
light "end of
programme".
The machine does not fill
with water
- continuous flashing of
the indicator light of
the running programme
- 2 flashes of the
indicator light "end of
programme".
The dishwasher will not
drain
34
Possible cause
Solutions
The water tap is blocked or
furred with limescale.
Clean the water tap.
The water tap is turned off.
Turn the water tap on.
The filter (where present) in
the threaded hose fitting at
the water inlet valve is
blocked.
Clean the filter in the
threaded hose fitting.
The water inlet hose has not
been correctly laid or it is
bent or squashed.
Check the water inlet hose
connection.
The sink spigot is blocked.
Clean out the sink spigot.
The water drain hose has not
been correctly laid or it is
bent or squashed.
Check the water drain
hose connection.
152955 17/2en
13-10-2005
15:59
Pagina 35
Operating instructions
- continuous flashing of
the indicator light of
the running programme
Anti-flood device has
activated.
Close the water tap and
contact your local Service
Force Centre.
- 3 flashes of the
indicator light "end of
programme".
Once the checks have been carried out, close the door and press the
button of the programme that was running before the intervention of
the alarm, the programme will continue from the point at which it was
interrupted. If the fault code reappears contact your local Service
Force Centre.
For other combinations of fault codes not described in the above chart
will appear, please contact your local Service Force Centre.
...there are problems when operating the dishwasher
Fault
The programme does not
start
There is a whistling noise
during washing
Possible cause
Solutions
The dishwasher door has not
been properly closed.
Close the door.
The main plug is not plugged
in.
Insert the mains plug.
The fuse has blown in the
household fuse box.
Replace the fuse.
For dishwasher models with
delay start option:
Delay start has been selected.
If dishes are o be washed
immediately, cancel the
delay start.
The whistling is not a cause
for concern.
Use a different brand of
detergent.
35
152955 17/2en
13-10-2005
15:59
Pagina 36
Operating instructions
...the wash results are not satisfactory
The dishes are not clean
●
●
●
●
●
●
●
●
The wrong washing programme has been selected.
The dishes were arranged in such a way as to stop water reaching all
parts of the surface. The baskets must not be overloaded.
The spray arms do not rotate freely due to wrong arrangement of
the load.
The filters in the base of the washing compartment are dirty or
incorrectly positioned.
Too little or no detergent has been used.
Where there are limescale deposits on the dishes; the salt container
is empty or the wrong level of the water softener has been selected.
The drain hose connection is not correct.
The salt container cap is not properly closed.
The dishes are wet and dull
●
●
Rinse aid was not used.
The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on glasses
and dishes
●
Decrease rinse aid dosing.
Water drops have dried onto glasses and dishes
●
●
36
Increase rinse aid dosing.
The detergent may be the cause. Contact the detergent
manufacturer’s consumer care line.
152955 17/2en
13-10-2005
15:59
Pagina 37
Service
If after all these checks, the problem persists, contact your local
Service Force Centre, quoting the model (Mod.), product number (PNC)
and serial number (S.N.).
This information can be found on the rating plate located on the side
of the dishwasher door (see picture).
Mod.
.
Prod.N
.......
o. .......
.
Ser.
No.
.......
..
So that you always have these numbers
at hand, we recommend you to make a
note of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . .
This product should be serviced by an authorised service engineer, and
only genuine spare parts should be used.
Under no circumstances should you attempt to repair the machine
yourself.
Repairs carried out by inexperienced persons may cause injury or
serious malfunctioning. Contact your local Service Force Centre.
Always insist on genuine spare parts.
37
152955 17/2en
13-10-2005
15:59
Pagina 38
Service
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to
purchase spare parts please contact your local Service Force Centre by
telephoning:
08705 929929
Your telephone call will be automatically routed to the Service Force
Centre covering your post code area.
For the address of your local Service Force Centre and further
information about Service Force, please visit the website at
www.serviceforce.co.uk
Before calling out an engineer, please ensure you read the details
under the heading "Something not working".
When you contact the Service Force Centre you will need to give the
following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the
rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
For Custom er Service in The Republic of Ireland please contact us at
the address below:
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0)1 4090751
Email: service.eid@electrolux.ie
38
152955 17/2en
13-10-2005
15:59
Pagina 39
Service
Customer Care Department
For general enquiries concerning your AEG-Electrolux appliance or for
further information on AEG-Electrolux products, please contact our
Customer Care Department by letter or telephone at the address below
or visit our website at:
www.AEG.co.uk
Customer Care Department
Major Appliances
Electrolux
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 350350 (*)
* calls to this number may be recorded for training purposes
To buy accessories, consumables and spare parts at our online shop
please visit: http://www.aeg-electrolux.co.uk
39
152955 17/2en
13-10-2005
15:59
Pagina 40
Guarantee Conditions
Guarantee Conditions
Standard Guarantee Conditions
We, AEG-Electrolux, undertake that if within 12 months of the date of
purchase this AEG-Electrolux appliance or any part thereof is proved to be
defective by reason only of faulty workmanship or materials, we will, at our
option repair or replace the same FREE OF CHARGE for labour, materials or
carriage on condition that:
● The appliance has been correctly installed and used only on the electricity
supply stated on the rating plate.
● The appliance has been used for normal domestic purposes only, and in
accordance with the manufacturer’s instructions.
● The appliance has not been serviced, maintained repaired, taken apart or
tampered with by any person not authorised by us.
● All service work under this guarantee must be undertaken by a Service
Force Centre.
● Any appliance or defective part replaced shall become the Company’s
property.
● This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits
may be available outside these hours in which case a premium will be
charged.
Exclusions
This guarantee does not cover:
● Damage or calls resulting from transportation, improper use or neglect,
the replacement of any light bulbs or removable parts of glass or plastic.
● Costs incurred for calls to put right an appliance which is improperly
installed or calls to appliances outside the United Kingdom.
● Appliances found to be in use within a commercial environment, plus
those which are subject to rental agreements.
● Products of AEG-Electrolux manufacture which are not marketed by
AEG-Electrolux.
40
152955 17/2en
13-10-2005
15:59
Pagina 41
Guarantee Conditions
European Guarantee
If you should move to another country within Europe then your guarantee
moves with you to your new home subject to the following qualifications:
● The guarantee starts from the date you first purchased your product.
● The guarantee is for the same period and to the same extent for labour
and parts as exists in the new country of use for this brand or range of
products.
● This guarantee relates to you and cannot be transferred to another user.
● Your new home is within the European Community (EC) or European Free
Trade Area.
● The product is installed and used in accordance with our instructions and
is only used domestically, i.e. a normal household.
● The product is installed taking into account regulations in your new
country.
Before you move please contact your nearest Customer Care centre, listed
below, to give them details of your new home. They will then ensure that the
local Service Organisation is aware of your move and able to look after you
and your appliance.
France
Germany
Italy
Sweden
UK
Ireland
Senlis
Nurenberg
Pordenone
Stockholm
Luton
Dublin
+33 (0) 344 62 20 13
+49 (0) 800 234 7378
+39 (0) 800 11 7511
+46 (0) 20 78 77 50
+44 (0) 8705 350350
+353 (0)1 4090753
41
152955 17/2en
13-10-2005
15:59
Pagina 42
Operating instructions
Technical specifications
Dimensions:
Width
Height with worktop
Height without worktop
Max depth
Max depth with open door
Electrical connection:
Voltage
Overall power
Fuse
Information on the electrical connection is given on the
rating plate on the inner edge of the dishwasher’s door.
Water supply pressure:
Minimum
Maximum
Capacity:
45 cm
85 cm
82 cm
63 cm
118.5 cm
50 kPa (0.5 bar)
800 kPa (8 bar)
9 place settings
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent
modifications.
42
152955 17/2en
13-10-2005
15:59
Pagina 43
Installation instructions
Installation instructions
Any electrical and/or plumbing work required to install this
appliance should be carried out by a qualified electrician and/or
plumber or competent person.
Remove all packaging before positioning the machine.
If possible, position the machine next to a water tap and a drain.
Fitting under a counter
(kitchen worktop or sink)
By removing the machine’s worktop, you can install it under a close
fitting sink unit or a pre-existing top, providing the dimensions of the
recess correspond to those shown in the picture.
Proceed as follows:
Remove the machine’s worktop by
unscrewing the two rear retaining
screws, pull the worktop from the back
of the machine and slide out the front
slots, lifting the worktop.
Insert the machine after adjusting height
and levelling with the adjustable feet.
When inserting the machine, ensure that
the water inlet and drain hoses are not
kinked or squashed.
During all operations that involve accessibility to internal components
the dishwasher has to be unplugged.
Be sure that once the appliance has been installed, it is easily
accessible for the service engineer in the event that a repair is
required.
If the dishwasher is later used as a free-standing appliance, the
original worktop must be re-mounted.
The plinth on free-standing appliances is not adjustable.
Levelling
Good levelling is essential for correct closure and sealing of the door.
When the appliance is correctly levelled, the door will not catch on
either side of the cabinet.
If the door does not close correctly, loosen or tighten the adjustable
feet until the machine is perfectly level.
43
152955 17/2en
13-10-2005
15:59
Pagina 44
Installation instructions
Water supply connections
This dishwasher must be plumbed into a cold water supply.
For making the connection itself, the coupling nut fitted to the
machine’s supply hose is designed to screw onto a 3/4" inch gas thread
spout.
The water pressure must be within the limits given in the "Technical
specifications". Your local Water Authority will advise you on the
average mains pressure in your area.
The water inlet hose must not be kinked, crushed, or entangled when it
is being connected.
The inlet hose must hang down vertically from the supply tap.
The dishwasher features fill and drain hoses which can be turned
either to the left or the right to suit the installation by means of the
locknut. The locknut must be correctly fitted to avoid water leaks.
(Attention! NOT all models of dishwashers have fill and drain hoses
provided with locknut. In this case, this kind of facility is not
possible).
If the machine is connected to new pipes or pipes which have not
been used for a long time, you should run the water for a few minutes
before connecting the inlet hose.
Do not use, for connection, old hoses which have been used with
another appliance.
The dishwasher is fitted with safety devices that prevent the wash
water returning into the drinking water system and comply with the
applicable plumbing regulations.
44
152955 17/2en
13-10-2005
15:59
Pagina 45
Installation instructions
Water inlet hose with safety valve
After connecting the double-walled water inlet hose, the safety valve
is next to the tap. Therefore the water inlet hose is only under pressure
while the water is running. If the water inlet hose starts to leak during
this operation, the safety valve cuts off the running water.
Please take care when installing the water inlet hose:
- The electrical cable for the safety valve is in the double-walled
water inlet hose. Do not immerse the water inlet hose or the safety
valve in water.
- If water inlet hose or the safety valve is damaged, remove the mains
plug immediately.
- A water inlet hose with safety valve must only be replaced by a
specialist or by the Service Force Centre.
- Place the water inlet hose in such a way that it is never higher than
the bottom edge of the safety valve.
45
152955 17/2en
13-10-2005
15:59
Pagina 46
Installation instructions
Water outlet hose connection
The end of the drain hose can be connected in the following ways:
1. To the sink outlet spigot, securing it to the underside of the work
surface. This will prevent waste water from the sink running into the
machine.
2. Hooked over the edge of the sink using the special curved plastic
guide (if provided with the machine).
3. To a stand pipe provided with vent-hole, minimum internal
diameter 4 cm.
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.
The drain hose can face either to the right or left of the dishwasher
Ensure the hose is not bent or squashed as this could prevent or slow
down the discharge of water.
The sink plug must not be in place when the machine is draining as
this could cause the water to syphon back into the machine.
If you use a drain hose extension it must be no longer than 2 metres
and its internal diameter must be no smaller than the diameter of the
hose provided.
Likewise the internal diameter of the couplings used for connections
to the waste outlet must be no smaller than the diameter of the hose
provided.
Attention!
Our appliances are supplied with a security device to protect against
the return of dirty water back into the machine.
If the spigot of your sink has a "no return valve" incorporated this can
prevent the correct draining of your dishwasher.
We advise you therefore to remove it.
46
152955 17/2en
13-10-2005
15:59
Pagina 47
Installation instructions
Electrical connection
This appliance must be earthed.
The manufacturer declines any responsibility should this safety
measure not be observed.
If the plug that is fitted to your appliance is not suitable for the
socket, it must be cut off and the appropriate plug fitted.
Important
The wires on the mains lead are coloured in accordance with the
following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
If you fit your own plug, the colours of the wires in the mains lead of
your appliance may not correspond with the markings identifying the
terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the terminal in the
plug which is marked with the letter "E" or the earth symbol
or
coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug which is
marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the plug which is
marked with the letter "L" or coloured red.
47
152955 17/2en
13-10-2005
15:59
Pagina 48
Installation instructions
The plug moulded onto the lead incorporates a 13amp BSI362 fuse.
Only ASTA or BSI fuses should be used.
The plug must not be used if the fuse cover/carrier is lost. The
cover/carrier is indicated by the coloured insert at the base of the
plug.
A replacement cover/carrier must be obtained from your local Service
Force Centre.
To isolate the dishwasher from mains, remove the mains plug.
Important!
The plug must still be accessible after the appliance has been
installed.
The appliance should not be connected to the electrical supply by
means of an extension cable.
In case that the electrical cable has to be replaced, please contact
your local Service Force Centre.
Warning!
A cut off plug inserted into a 13 amp socket is a serious safety
(shock) hazard. Ensure that it is disposed of safely.
48
152955 17/2en
13-10-2005
15:59
Pagina 49
Hints for test centres
Hints for test centres
Testing in accordance with EN 60704 must be carried out with
appliance fully loaded and using the test programme (see "Washing
programmes" chart).
Test in accordance with EN 50242 must be carried out when the salt
dispenser and rinse aid container have been filled with salt and rinse
aid respectively and using the test programme (see "Washing
programmes" chart).
Load:
9 standard place settings
Rinse aid setting
Position 4 (type III)
Detergent dosage:
5 g + 20 g (type B)
Arrangement upper
basket without smaller
bowl and salad-bowl
Arrangement upper
basket with smaller bowl
and salad-bowl
Arrangement
lower basket
Arrangement cutlery basket
Cup racks: position A
49
152955 17/2en
13-10-2005
15:59
Pagina 50
152955 17/2en
13-10-2005
15:59
Pagina 51
152955 17/2en
13-10-2005
15:59
Pagina 52
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, vacuum cleaners, chain
saws and lawn mowers) are sold each year to a value of approx. 14 billion USD in more than 150 countries
around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
152 955 17/2
Subject to change without notice
10/05
Download PDF

advertising