Electrolux 55750 Dishwasher User Manual

ÖKO-FAVORIT 55750
Dishwasher
Instructions for Use
Dear Customer
Please read these operating instructions carefully.
Please make sure you read the safety instructions on
the first pages of these operating instructions! Keep
the operating instructions for future reference. Pass
them on to any future owners.
With the warning triangle and/or by means of
key words (Warning!, Caution!, Important!),
information is emphasized which is important
for your safety or the correct functioning of
the appliance. It is essential that this informa
tion is observed.
1. This symbol guides you step by step when operating
the appliance.
2. . . .
3. . . .
Next to this symbol you receive additional in
formation and practical tips on using the ap
pliance.
Tips and information about the economical
and environmentally friendly use of the ma
chine are marked with the clover.
These operating instructions contain information ab
out how to independently solve any problems which
may arise. See "What to do if...".
This appliance conforms
with EC-Directive 73/23/EEC, 90/683/EEC,
89/336/EEC, 93/68/EEC
2
Content
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
General Hints & Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Prior to Using for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
The Crockery Basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Filling with Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the rinse aid dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filling the salt dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Water Softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The first wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
8
8
Cutlery basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lower basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
11
Filling with detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Selecting and starting the program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Program Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Unloading the crockery basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
Remedying faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Information for Test Institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Program display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remaining running time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End of the program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correcting or Deleting the Program Selection / Pre-selected Start Time . . . . . . . . . . . . . . . . . . . . . .
ECO button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mains power loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Re-filling the salt dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refilling the rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the large strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the fine strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the spray arm nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appliances with stainless steel outer surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
14
14
15
15
17
17
18
18
18
18
19
19
20
20
22
3
Safety Instructions
The safety aspects of this appliance comply with the accepted technical standards and the applicable safety regula
tions. Nevertheless, we consider it our obligation to make you aware of the following safety information:
Installation
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
• Any plumbing work required to install this ap
pliance should be carried out by a qualified plumber
or competent person.
• This appliance is heavy. Care should be taken when
moving it.
• It is dangerous to alter the specifications or attempt
to modify this product in any way.
• Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Child Safety
• This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
• Keep all packaging well away from children.
• Keep all detergents in a safe place out of children's
reach.
• Keep children away from the appliance when the
door is open, and take care when closing the door
not to trap childrens fingers.
Before Use
• Check your dishwasher for any transport damage.
Never connect a damaged appliance. If your ap
pliance is damaged contact your retailer.
• Before using your dishwasher for the first time, en
sure the voltage and current rating in your home is
the same as indicated on the rating plate.
During use
• Items that are contaminated by petrol paint, steel
or iron debris, corrosive, acidic or alkaline chemicals
must not be washed in this dishwasher.
• Under no circumstances should you open the door
whilst the appliance is in operation. Always turn off
the appliance before opening the door.
• Only use detergent specifically designed for use in
dishwashers.
• Long bladed knives stored in an upright position are
a potential hazard.
• Long and/or sharp items of cutlery such as carving
knives must be positioned horizontally in the upper
basket.
4
• When finished loading or unloading close the door,
as an open door can be a hazard.
• Isolate the appliance from the power supply and
turn off the water supply after use.
• Care should be taken when cleaning the bottom
door seal and hinge area as any exposed metal ed
ges may cut if care is not taken.
• This product should be serviced by an authorised
Service Engineer, and only genuine spare parts
should be used.
• Under no circumstances should you attempt to re
pair the machine yourself. Repairs carried out by in
experienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre.
• In the case of a fault, turn off the appliance, discon
nect the appliance from the water supply and con
tact your local Service Force Centre.
• Never sit or stand on the open door.
• If the power supply cable of your dishwasher is da
maged, it must be replaced by a cable available from
your local Service Force Centre.
• The water protection system prevents any water da
maged providing:
- The dishwasher is connected to the mains sup
ply.
- The dishwasher is correctly installed.
Environmental Information
Packaging: All packing materials used are environmen
tally friendly and reusable. The cardboard parts are
made from recycled paper, and the wood parts are un
treated. The plastics are marked as follows:
"PE" for polyethylene - e.g. packaging foil
"PS" for polystyrene
"POM" for polyoxymenthylene
Old appliances: When disposing of an old appliance,
cut off the power supply cable and remove any door
catches, to prevent young children being trapped in
side.
Contact your local Council or Environmental Health
Office to see if there are cycling facilities in your area.
Keep this instruction book for
future reference and ensure it is
passed on to any new owner.
Description of the Appliance
Dishwasher
Cover for spray arm
Centre spray arm
Upper dish basket
(height-adjustable)
Setting switch for water softener
Coarse strainer
Cutlery basket top
Lower spray arm
Water inlet valve: do not open,
do not fill with water
Salt container
Fine strainer with
micro-strainer
Curtlery basket
Lower basket
Rinse aid container
Display window for rinse aid
Detergent container
Rating plate
Programme guide
Control Panel
Pre-rinse
Clean
Dry
Rinse
Half load
Mains switch
Programme end
Start time / Remaining time display
Programme sequence display
Regenerating salt
control lamp
Clear rinse agent
control lamp
Economy
Stop
Program button Pre-rinse,
with control lamp
Program button Quick,
with control lamp
Program button Intensive,
with control lamp
Program button Normal,
with control lamp
Program button Gentle, with control lamp
Delay start button
5
General Hints & Tips
To save energy:
Items not suitable for dishwashers.
• Do not prewash dishes under running water.
• Wait until the dishwasher is full before washing a
load. If necessary use the rinse and hold button.
• If washing a reduced quantity of dishes up to maxi
mum of 50% of the capacity, use the half load but
ton (1/2).
• Always select a wash programme suitable for the
type of crockery being washed and to the level of
soiling (See Programme Chart).
• Follow the detergent dosage recommendations in
this instruction book and the detergent manufac
turers instructions. Never over dose or under dose.
• Ensure the water softener is correctly set.
The following items should not be washed in the
dishwasher (unless they are sold as dishwasher
proof).
• Cutlery with wooden or horn handles or glued parts
• Bronze cutlery
• Saucepans with wooden handles
• Aluminium ware
• Crystal ware
• Leaded glass
• Plastic items
• Antique or fine decorated china
• Tin and copper items
• Artistic objects
• Wooden board
For best washing and drying results
• Before loading remove all scraps of food and soak
very heavily soiled pots and pans.
• Arrange saucepans, cups and glasses etc. upside
down.
• Tilt items with convex or concave surfaces so the
water drains off easily.
• Avoid contact between the dishes as far as possible.
• Wait a few minutes before removing the dishes; in
this way they will be cooler and the drying will be
improved.
• Empty the lower basket first and then the upper
basket; this will avoid water dripping from the up
per basket onto the dishes in the lower one.
• You will improve drying results by leaving the dish
washer door ajar for at least 15-30 minutes as soon
as the programme finishes.
Crockery that may be suitable:
• Earthenware crockery can be washed in the dish
washer if the manufacturer has indicated that it is
suitable.
• Some glazed finishes may fade after frequent ma
chine washing.
• Silver and aluminium parts tend to discolour during
machine washing.
• Copper, pewter and brass tend to stain.
• A chemical reaction can occur between silver cut
lery and stainless steel cutlery. As a precaution do
not wash together.
• Iron and cast iron objects can rust and stain other
items.
• Certain types of decoration can discolour when
washed in a dishwasher.
If in doubt check with the manufacturer of the item.
When buying new dishes, ensure that they are dishwas
her proof.
For best results we recommend the use of Finish detergents, rinse aid and salt.
6
Prior to Using for the First Time
Carry out the following steps before using your dish
washer for the first time.
A
Filling with Rinse Aid
Rinse aid is automatically added during the last rinse,
ensuring thorough rinsing, spot and streak free drying.
A If the rinse aid display light is lit on the control
panel, open the dispenser by turning the sealing
cap to the left.
B
B Fill with rinse aid up to the "max" mark. Do not ex
ceed the maximum container mark of 150 ml.
- Close the dispenser.
- Remove any spillage to prevent foaming.
The rinse aid display light on the control panel will go
out.
Setting the rinse aid dosage
According to the finish and drying results obtained, the
rinse aid dosage can be adjusted. Position 1 minimum
dosage, position 6 maximum dosage.
B
The factory setting is level 3.
Gradually increase the dosage if there are drops of wa
ter or lime spots on the dishes after washing. Reduce
it if there are sticky whitish streaks on the dishes.
Filling the salt dispenser
A
Warning! Only use special salt for dishwashers.
Other types of salt (e.g., cooking salt) often
contain water-insoluble components which
can block the water softener and may render
it unserviceable.
Salt and detergent packages often look very
similar. Detergent accidentally poured into the
salt dispenser will damage the water softener.
Each time you fill with special salt, ensure that
you are really holding a salt package in your
hand.
Fill with salt as follows:
A Open the cap of the salt dispenser.
B Fill the dispenser with water
7
C Fill with 1 kg of special salt. As a result, approx. 1
litre of water will be displaced.
A
- Remove salt from around the opening of the dis
penser.
B
- Close the salt dispenser by turning the cap until
the stop is reached.
- Immediately run the "Pre-rinse"program to
wash away any salt residues.
Never fill the salt dispenser with rinse aid or
detergent!
The salt display will go out after 1 or 2 rinse cycles.
Do not remove the water feed valve, and do not
fill with detergent for any reason.
C
Setting the Water Softener
The dishwasher is equipped with a water softener de
signed to remove minerals and salts from the water
supply, which would have a detrimental or adverse ef
fect on the operation of the appliance.
The higher the content of these salts, the harder your
water is.
The softener should be adjusted according to the hard
ness of the water in your area. Your local Water author
ity can advise you on the hardness of the water in your
area.
Adjust the dosage as follows:
Turn the setting button using a coin or a screwdriver
until the arrow on the knob points to the desired num
ber.
The arrow must point to a number and the po
sition must be engaged positively.
Clarke French degrees
(°TH)
degrees
PPM (Parts
per Million)
Level
0-9
0 - 12,5
0 - 125
1
9 - 18
12,5 - 25
125 - 250
2
18 - 26
25 - 37,5
250 - 375
3
26 - 35
37,5 - 50
375 - 500
4
> 35
> 50
> 500
5
The first wash cycle
- When using for the first time, use the Intensive pro
gram.
8
4
3
5
2
1
The Crockery Basket
Before loading, remove any food scraps. Do not
rinse with warm water or use a manual deter
gent.
The illustration gives you some tips for the op
timal loading of your dishwasher.
Lower basket
Heavily soiled, large pieces of crockery will be tho
roughly cleaned in the lower basket.
- Pull out the lower basket to its full extent.
- Arrange large and heavy pieces of crockery, such as
plates, bowls, pots etc., in the lower basket.
Cutlery basket
without cutlery basket top
- Place cutlery in the cutlery basket with the handles
downward, except for cutlery very narrow handles,
which could penetrate through the cutlery basket
and could block the spray arm.
- With the top fitted to the cutlery basket, the cutlery
no longer touches. All parts are accessible for the
water jet. In this way, cleaning and drying of the
cutlery is improved.
with cutlery basket top
Important:
Long bladed knives stored in an upright posi
tion are a potential hazard.
Long and / or sharp items of cutlery such as
carving knives must be positioned horizontally
in the upper basket.
Take care when loading or unloading sharp
items such as knives.
Removing the cutlery basket top
- Press in the clips slightly (A) and remove the cutlery
basket top upwards (B).
9
Lower basket
Adjustable plate rail, right, 10 piece
In order to make optimal use of the space in the lower
basket, the plate rails can be set in two positions, in the
longitudinal and transverse directions.
A
- To take out the plate rails, the plate rail grip must
be pulled away upwards (A).
- The plate rails are then put into the transverse posi
tion by fitting them into the longitudinal struts (D)
on the lower basket, and then pressing down the
plate rail (B) until it snaps into place.
The plate rail can be varied sideways (C). Positioning as
described above.
B
D
C
A
Adjustable plate rail insert, 5 piece
For deep plates or bowls, a part of the left plate rail can
be removed.
B
- To remove the plate rail insert, the plate rail grip is
pulled away upwards (A).
- The plate rail insert can also be used instead of the
10-piece plate rail, right (B).
B
D
10
Hinged plate rail, left
For large bowls and pots, the plate rail can be unhin
ged.
1
2
Remove the 5 piece plate rail inserts and cutlery basket.
Pull the plate rail slightly upwards, and fold down onto
the basket base to the right.
Important
The crosswise plate rack on the front right is optimally
suited to small, flat plates with a diameter of 170-210
mm.
Upper basket
Delicate, smaller pieces of crockery are gently washed
in the upper basket.
- Pull out the upper basket to the stop.
- Arrange the small, light and delicate pieces of crok
kery such as saucers, cup's, glasses and tempera
ture-resistant plastic parts in the upper basket.
Fig. A
Adjustable glass holder
- For stem glasses, suspend the glass holder in the
right-hand position (Fig. A) and fold it up.
Fig. B
- For high, cylindrical glasses, suspend the glass hol
der in the let-hand position (Fig. B) and fold it up.
- Glasses can also be placed over the protruding rods
(Fig. C).
- To unload the glass holder, or if it is not being used,
fold it back to the right.
Fig. C
Adjustable Cup Support
Arrange crockery offset on and below the hinged cup
support, so that the spray jet can reach all parts. Stem
glasses can be suspended from the cut-outs in the cup
support.
The cup support can be positioned at two different
heights.
11
The upper basket is adjustable to the
right
- Set the upper basket to the desired height, corres
ponding to your crockery.
Even possible with the upper basket loaded.
Raising:
- Pull out the upper basket.
- Lift up the right side.
- Pull forward to the stop, and latch into the upper
position.
Lowering:
- Pull out the upper basket
- Lift the right side, and lower into the lower position.
Before washing, check that the spray arm can
rotate freely.
Maximum plate size
Upper basket: top position
Maximum plate size
Upper basket: bottom position
∅ 21
∅ 19
∅ 30
∅ 27
Large plates placed at an angle
12
∅ 28
∅ 25
Filling with detergent
A
Never use hand cleaning liquids or commercial
cleaners.
Only use commercially-available detergents
that are suitable for use in domestic dishwas
hers.
The detergent dispenser is normally open.
MAX
If it is closed:
MIN
B
A Press the button downwards, and the dispenser
will open.
C
B Fill the dispenser with detergent according to the
instructions of the detergent manufacturer. Only
place "tabs" in the detergent dispenser or the
cutlery basket in accordance with the informa
tion of the manufacturer.
C Press the dispenser lid shut.
D For warm Pre-rinse program, detergent can also
be filled in the dip of the lid.
D
Selecting and starting the program
1. Push the crockery basket completely in.
2. Fold up the door, and press it shut.
The door lock must latch, otherwise the ma
chine will not start.
3. Press the mains switch.
4. Press the Half Load button if only half the amount
of dishes are loaded.
5. Select one of the programs 1 - 5. Refer to the Pro
gram Table.
The indicator lamp for the selected programme flashes
for 5 seconds before the wash programme starts.
Half load
Mains switch
Economy
6. For a period of 5 seconds it is possible to change to
another programme, and also to select the Eco but
ton or the Half Load button.
After each press of a button, there is a period
of 5 seconds during which any corrections can
be made.
Do not open the door after the program has started!
To prevent scolding and damage to units by escap
ing steam.
13
Program display
The illuminated symbols in the display indicate which
phase of the program is currently running.
Remaining running time
As soon as a program starts, the time remaining lights
up in the display field in minutes. This time varies de
pending on the loading and temperature of the incom
ing water. The display may remain at one time for sevral
minutes. It may also jump in time this quite normal,
and does not indicate a fault.
End of the program
The illumination of a "0" in the start delay display and
the program end symbol in the program display indi
cate the end of the washing program.
Safety lock
The safety lock prevents an accidental restart after the
end of the program. In order to be able to enter a new
program, the dishwasher must either be switched off
and then on again, or the door must be opened and
then closed again.
The safety lock is released as soon as only the
Programme End symbol is illuminated in the
programme display.
Delay start
The start of the selected program can be delayed bet
ween 1 and 9 hours in steps of 1 hour using the Start
Time Pre-selection button.
- By repeatedly pressing the button, the delay time
can be programmed in hours, and will be dis
played in the display field. Display: Hours and a
small "h".
14
Pre-rinse
Drying
Cleaning
Rinsing
Program end
A washing program can be selected first, and
then the pre-selected start time can be pro
grammed, or vice versa.
If a pre-selected start time is programmed without a
washing program, the programmed time goes out after
5 seconds. After selecting a program, the selection of
the start delay must take place within 5 seconds.
An activated pre-selected start time will be indicated
in the display field by a blinking dot.
After the pre-selected start time has expired, the
machine starts up the selected program automati
cally.
Correcting or Deleting the
Program Selection / Pre-se
lected Start Time
Using the Stop button, a running program or the preselected start time can be interrupted or cancelled.
Interruption:
- Briefly activating the Stop button causes an inter
ruption of all programs, and the Stop control lamp
blinks.
- Activating the Stop button again makes the pro
gramming active once again.
Cancelling:
- Holding down the Stop button longer than 2 se
conds deletes the program and the pre-selected
start time, and any water present will be pumped
out. The Program End symbol in the display lights up
as soon as all the water has been pumped out.
ECO button
The wash temperature is reduced using the ECO button,
as a result less energy is consumed during heating up.
The economy button can be selected for all wash pro
grams.
The ECO button should be used in particular when
using low-alkali compact cleaners with enzymes. The
enzymes produce their full dirt-releasing effect in a
temperature range between 40 and 50 °C.
Half load
Mains switch
Economy
15
Duration of
programm
Drying
Rinsing
Intermediate
Rinse
Clean
Pre-rinse
Program Chart
Gentle
Light to normally soiled crockery
45°C
65°C
59 min.
+ ECO
Lightly soiled crockery
40°C
60°C
48 min.
+
Lightly soiled crockery with half load
40°C
60°C
45 min.
Heavily-soiled crockery
50°C
68°C
70 min.
+ ECO
The most economical programme for
stubborn dirt. Using this programme, AAA
performance in accordance with the
EN 50242 "Energy Label" is achieved *)
50°C
68°C
2.5 h
+
Normally soiled crockery with half load
ÇÇ
ÇÇÇÇÇÇÇ
ÇÇÇÇÇÇÇÇÇ
Normal
Intensive
ÇÇÇÇÇ
ÇÇÇÇÇÇÇ
ÇÇÇÇÇÇÇÇÇÇÇÇ
50°C
65°C
64 min.
Very heavily-soiled crockery
47°C
68°C
73°C
86 min.
+ ECO
Heavily to very heavily-soiled crockery
40°C
63°C
68°C
81 min.
+
Heavily to very heavily-soiled crockery
with half load
40°C
63°C
68°C
75 min.
Very light to lightly soiled crockery
45°C
65°C
44 min.
+ ECO
very lightly soiled crockery
40°C
60°C
38 min.
+
very lightly soiled crockery with half load
40°C
60°C
34 min.
Quick
Pre-rinse
Wash off cold
ÇÇÇÇÇÇÇÇÇÇÇÇ
ÇÇÇÇÇÇÇÇÇÇÇÇ
Ç ÇÇÇÇÇÇ
Ç ÇÇÇÇÇÇ
ÇÇÇÇ
5
The programme times and temperatures are intended as a guide only. The actual programme times will de
pend an incoming water temperature an pressure
*)
16
A = Best energy efficiency
A = Best cleaning result
Programme with significantly extended drying
A = Best drying result
Mains power loss
In case of a power failure, or a deliberate disconnection
to the power supply, all the set values are retained.
Error message
Start time /
Remaining time
display
Programme
sequence display
The electronics of the dishwasher can independently
recognise and display faults. If a fault occurs, an error
code in the display, one of the program control lamps
and the Program End symbol in the display will blink.
Please note down this error code before making con
tact your Service Centre.
The error message is deleted by switching off the main
switch.
Mains switch
Error codes and possible causes
A = Water tap closed, inlet hose filter blocked
C = Drain hose, coarse or fine strainer or sink trap
blocked
E
= Water pressure too low, water tap not completely opened, inlet hose or inlet hose filter is
blocked, machine losing water.
E2 = Call AEG Service force
H = Call AEG Service force
L
= Call AEG Service force
Unloading the crockery basket
After the washing program is complete:
First unload the lower basket.
Then unload the upper basket, so that no drops of wa
ter fall onto the dry crockery in the lower basket.
Inspect the coarse strainer after every washing
sequence. Clean as necessary.
17
Cleaning and care
Internal Cleaning
Ensure that the seals around the door, the detergent
and rinse aid dispensers are cleaned regularly with a
damp cloth.
We recommend the use of Finish Dishwasher Cleaner,
every 3 months or run a 65oC wash without dishes
using detergent. Regular use of Finish Dishwasher
Cleaner cleans inaccessible parts, eliminates unplea
sant food odours and helps prevent the build-up of li
mescale.
Re-filling the salt dispenser
Never fill the salt dispenser with rinsing aids or
detergents!
When the salt replenishment lamp lights up, you must
refill the special salt for the water softener.
Proceed as described in the "Using for the First Time"
chapter, however you do not need to add any water
during this process.
Immediately after refilling, run the "Pre-rinse"
program to wash away any salt residues.
Refilling the rinse aid
When the rinse aid light on the control panel lights up,
you must refill with rinse aid.
Proceed as described in the "Using for the First Time"
chapter.
Immediately remove any spilled rinse aid, as
otherwise foaming could occur.
Cleaning the large strainer
Check the large strainer after every cleaning run. Clean
as necessary.
- The large strainer can be simply pulled out and be
re-installed.
- Clean the strainer under running water.
18
Cleaning the fine strainer
The fine strainer must be cleaned from time to time:
- Unlock the strainer by turning it to position A, lift
out the fine strainer and clean it under running wa
ter with a brush.
- Place the strainer in its holder and secure it by tur
ning to position B.
Cleaning the spray arm nozz
les
A
B
Regularly check the nozzles on the three spray arms for
blockages. If necessary, clean out the nozzles with a
fine wire or a fine pin and a strong jet of water.
Take care not damage the nozzle openings.
Roof spray arm
Remove the roof spray arm:
- Loosen the securing screw (A) by turning to the
left.
- Pull the spray arm from the shaft.
- Clean the spray arm and the securing screw.
- Refix the spray arm with the securing screw (A)
by turning to the right.
A
B
Central spray arm
- Remove the central spray arm by turning it to the
side, and hoisting off.
The two-part spray arm bearing is held together by
a clamping spring (B).
- To re-install, press the central spray arm upwards
until you can feel it locking into place.
Lower spray arm
Remove the lower spray arm:
- Loosen the nut (C) by turning it to the left
C
- Pull the spray arm from the shaft
- Clean the nozzles
- Refix the spray arm with the nut (C) by turning to
the right.
19
Cleaning the appliance
Clean the outer surfaces of the machine, and in parti
cular the control panel, regularly using a soft, damp
cloth. Only use neutral detergents (e.g., hand washing
liquid), but not scouring agents or solvents such as ace
tone, paintbrush cleaner or thinners etc.
Appliances with stainless steel
outer surfaces
For the stainless steel front, we recommend thorough
and regular care and cleaning with suitable stainless
steel cleaners.
Pay attention to the instructions regarding detergents
and care products. Do not use abrasive or scouring
agents.
Before wiping, apply the detergent to a damp cloth,
clean the surfaces with it, and dry with a clean cloth.
When cleaning, ensure that the stainless steel surface
finish (the fine diagonal lines) is not worked against
the grain: no circular movements!
20
Remedying faults
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carryout the checks listed below.
Important:
If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or
installation a charge will be made even if the appliance is in guarantee.
The drain pump runs continually even when the ap
pliance is switched off.
- The water protection system has been triggered.
First close the water taps, and then pull out the
mains plug or switch off or turn out the fuses. Call
AEG Service Force.
The program does not start.
- Are the fuses of the fixed installation in order? Is the
appliance connected to the electrical supply?
- Has the door been properly closed? Press the door
shut until the door lock latches in.
- Has the pre-select start time been set?
The machine does not fill with water.
- Is the water tap completely open?
- Is the water tap blocked? Open and close the water
tap several times.
- Is the strainer in the hose fitting to the water tap
blocked? Clean the strainer if necessary.
- Is the inlet hose kinked? Check the hose run.
- Is a minimum water flow pressure of 1 bar availa
ble?
The program sequence display remains static at the
start of the cleaning
- Is the water tap completely open?
- Is the strainer in the hose fitting at the water tap
blocked? Clean if necessary.
The water is not pumped away
- Is the drain hose kinked? Check the run of the hose
(see the "Water Drainage" section).
- Is the sink drain blocked? Clear any blockages.
The crockery is not clean
- Have you selected a program that is suitable for
the type and degree of soiling of your crockery?
(see Program Chart)
- Have you arranged the crockery so that the
sprayed water has access to all surfaces, both in
ternal and external? The crockery baskets must
not be overfilled.
- Was the spray arm blocked by crockery or pieces
of cutlery?
- Are the spray arm nozzles clean?
- Are all the filters in the bese of your dishwasher
clean? Have the filters been installed correctly?
-
Have you used the correct amount of detergent?
Is the drain hose correctly filted.
Is the on-site sink drain blocked?
Is there salt in the salt dispenser? Without it, the
water will not be softened. Lime deposits can
form on your crockery and in the machine.
- Has the water softener system been set to the
local water hardness?
The crockery is not dry, and has no sparkle.
- Is there rinse aid in the dispenser?
- Has the salt dosage been correctly set?
Glasses and dishes have streaks, stripes, milky blot
ches or blue-coloured bloom.
- The rinse aid is being overdosed. Set a lower rinse
aid dosage
Glasses and dishes have dried-on "water drops".
- The rinse aid is being underdosed. Set the rinse
aid dosage higher.
- Is the lid of the salt container properly closed?
Rust marks can be seen in the washing area.
- The dishwasher interior is made of stainless steel.
Rust marks inside the dishwasher are caused by
external rust (rust particles from the water pi
ping, from pans, cutlery etc.). Remove such marks
using a commercially-available stainless steel
cleaner.
- Was the "Pre-rinse" program started immediately
after refilling the salt?
Error codes and possible causes
A = Water tap closed, inlet hose filter blocked
C = Drain hose, coarse or fine strainer or sink trap
blocked
E = Water pressure too low, water tap not completely opened, inlet hose or inlet new filter is
blocked, machine losing water.
E2 = Call AEG Service force
H = Call AEG Service force
L = Call AEG Service force
21
Service & Spare Parts
If you wish to purchase spare parts or require an engi
neer, contact your local AEG Service Force Centre by
telephoning:
08705 929929
Your telephone call will be automatically routed to the
Service Centre covering your post code area.
When you contact the Service Centre they will need
the following information:
1.
2.
3.
4.
Your name & address, including post code.
Your telephone number.
Clear and concise details of the fault.
The model, serial and production number.
(This information can be found the rating plate). In
order that you have this information to hand when
you call, we recommend you write the information
below.
Product No: .........................................................................
Serial No: .............................................................................
Model No: ............................................................................
5. Date of purchase.
Please note that it will be necessary to provide proof
of purchase for any in guarantee service call.
Inguarantee customers should ensure that the chap
ter headed `Remedying Faults' has been read, as the en
gineer will make a charge if the fault is not a mechani
cal or electrical breakdown.
Customer Care
For general enquiries concerning your AEG appliance
or for further information on AEG products please con
tact our Customer Care Department by letter or tele
phone as follows:
Customer Care Department
AEG Domestic Appliances
55-77 High Street
Slough
Berkshire SL1 1DZ
Tel: 08705 350350
22
Serial Number
Prod–Nr.:
Serie–Nr.:
Mod:
Modell
Technical Data
Dimensions
Width
Height
Max. depth
Max. depth with open door
Operational voltage
Frequency
54.6 cm
75.9 cm
57.0 cm
114.5 cm
230 V
50 Hz
Power consumption
Circulation pump
150 W
Power consumption
Heating elements
2000 W
Total power
2150 W 10 A
Mains water pressure
Cold or hot water up to
max. 65 °C
min.
max.
1 bar (flow pressure)
Capacity
Half load (1/2)
*Standard place settings IEC
*Standard place settings IEC
11
10 bar
6
Consumption
Intensieve
Intensieve + Eco
Intensieve + 1/2
Energy (kWh)
1,6
1,3
1,13
Water (l)
16
16
15
Normal
Normal + Eco
Normal + 1/2
1,0
1,0
0,9
16
15
15
Quick
Quick + Eco
Quick + 1/2
1,0
0,8
0,7
14
14
12
Gentle
Gentle + Eco
Gentle + 1/2
1,0
0,8
0,7
14
14
12
* A standard place setting consists of: 1 soup bowl, 1 flat plate, 1 dessert plate, 1 saucer, 1 cup, 1 glass, 1 knife, 1
fork, 1 soup spoon, 1 dessert spoon, 1 tea spoon.
23
Information for Test Institutes
Prior to the tests, the salt container for the
water softener and the rinse aid container
must be completely full.
Test standard:
EN 50 242
Comparison program:
Normal + Eco
Capacity:
tings
11 standard place set
Detergent dosing:
27,5 g in the detergent
container
Rinse aid dosing:
setting 6
Loading example:
Flat plates
Oval plates
Dessert plates
Soup plates
Soup plates
1-10
11
12
13-23
24
24
Soup spoons
Serving fork
Soup spoon
Forks
Sauce ladle
25-35
36-37
38-48
49-59
Knives
Serving spoons
Dessert spoons
Tea spoons
Dessert plates
Installation Instructions
UK
Any electrical work required to install this
appliance should be carried out by a quali
fied electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a quali
fied plumber or competent person.
• The dishwasher is delivered ready for connection,
i.e. with power supply cable, drain hose and inlet
hose with fitted filter and seal.
ECO
65˚
70˚
STOP
45˚
86 - 91 cm
• The installation should be carried out to connec
tions provided in a neighboring cupboard (not di
rectly behind the unit).
ÖKO_FAVORIT
45˚
• The regulations of the local water and electricity
companies must be complied with.
Water Supply Connections
• The dishwasher must be plumbed into a cold water
supply.
• The water pressure must be within the limits given
in the technical specifications. Your local Water Au
thority will advise you on the average mains pres
sure in your area.
• A shut-off device with a ¾" connection must be
provided on site.
600
• The inlet hose has a filter to remove any impurities
from the water supply and a rubber seal. When fit
ting ensure that the filter and seal are correctly po
sitioned.
510
No water must escape from the fitting after
the shut-off device has been opened.
Water outlet hose connection
• Ensure the drain hose is not bent or squashed as the
could prevent or slow down the discharge of water.
• The outlet hose should be connected to a water
outlet provided in a neighboring cupboard (not di
rectly behind the unit).
574
546
762
759
550
570
• The dishwasher is fitted with a device to prevent the
back flow of water, which allows the installation
height of the unit to be above the outlet height.
• The highest point of the drain hose should never ex
ceed the unit height.
AEG
153 0409 20 / 09.99
1
Electrical Connection
This appliance must be earthed.
The manufacturer declines any responsibil
ity should this safety measure not be ob
served.
Before switching on make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
Changing a fuse
Your appliance is supplied with a 13 amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363A) fuse must
be used,
Should the plug need to be replaced for any reason,
proceed as described below.
The wires on the mains lead are coloured in accordance
with the following code.
Green and Yellow
-Earth
Blue
-Neutral
Brown
-Live
The wired coloured green and yellow must be connec
ted to the terminal marked with the letter "E" or by the
earth symbol
or coloured green and yellow.
The wired coloured blue must be connected to the ter
minal "N" or coloured black.
The wire cooured brown must be connected to the ter
minal marked "L" or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
A cut off plug inserted into a 13amp socket
is a serious safety (shock) hazard.
Ensure that the cut of plug is disposed of sa
fely.
Permanent connection
In the case of permanent connection it is necessary
that you install a double pole switch between the ap
pliance and the electricity supply (mains), with a mini
mum gap of 3mm between the switch contacts and a
type suitable for the required load in compliance with
the current electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
AEG
153 0409 20 / 09.99
Assembly Instructions for the Side Rail Assembly Kit
Components:
1 off
1 off
4 off
4 off
4 off
Detail A
Side rail, right
Side rail, left
Spacer 4 mm
Spacer 3mm
Spax screw 4.0 x 20 galvanised
SL L
neighbouring
edge
SL R
SL L
DS 1
DS 2
SCHR
Detail B
DS 1
DS 2
600
SL L
SCHR
100
19
21
16
A+B
759
19
510min.
546
762
562568
1619
550
Procedure:
574
759
SL L
SL R
570
Frame side panel thickness 19 mm:
- Remove the protective tape of the two spacing washers (DS 1) mounted on the side rails (SL R + SL L).
- Position the side rail (SL L):
> Lower side (open) lying on the floor of the niche
> Edge lying against the side panel of the frame (see Detail A).
- Press on and fix the side rail (SL L), and secure with the supplied screws (2x SCHR
- Repeat this procedure for side rail SL R.
Frame side panel thickness 16 mm:
- Remove the protective tape of the two spacing washers (DS 1) mounted on the side rails (SL R + SL L).
- Stick the separately-supplied 3 mm spacing washers (SL R + SL L) over the pre-mounted 4 mm spacing washers
(DS 1) as shown in Detail B.
The adhesive tape of the 3mm spacing washer (DS 2) must be on the outer side.
- Continue as described for the 19 mm thick frame side panel.
153 0771 03 / 03.98
3
Installation
Detail A
• Stick on the damp protection film as described in
the instructions on the rear side of the film (shorten
where necessary).
• Attach the side rails to the side panels of the furni
ture as described in the separate assembly instruc
tions.
• Place the appliance in front of the high cupboard,
and run the cable and hoses through the high cup
board's bay so that they are neither kinked or squas
hed.
• Align the dishwasher in the centre of the bay and
flush with the side panels, and where necessary, ad
just to be flush at the front surface using shims.
• Carefully open the door of the appliance without
changing the settings of the appliance.
Detail B
• Using the pre-drilled holes, screw the appliance to
the side panels of the furniture on both sides in the
upper inner area (see Detail A).
• Before screwing the appliance diagonally through
the base plate using two additional screws (always
pre-drill), it is advisable to protect the appliance
door from damage using suitable materials (e.g. the
cardboard packaging). In order to tighten these
screws, the door must be opened by approx. 45 de
grees (see Detail B).
Technical Data
Dimensions
Height
Depth
Width
Capacity
Electrical connection
Motor rating during wash
Power of heating element
Overall power
Water supply pressure
AEG
75.9 cm
57.0 cm
54.6 cm
12 place settings
230-240V 50Hz
140 W
2000 W
2150 W
Minimum 1bar
Maximum 10 bar
153 0409 20 / 09.99
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
Copyright by AEG
153 0728 10 / 09.99 mh
26