Advertisement
Advertisement
The IR-5000 includes these items:
IR-5000
USERS GUIDE
All-In-One
IR System
1
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed.
This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800)
840-0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.
Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical environment applications. Channel Vision customers using or selling Channel Vision products for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale.
500-149 rev D
How IR repeating works
AB-500
Channe Point an
IR remote control at the IR receiver
The IR receiver is wired to the IR hub which routes the signal to IR emitters Be sure the emitter is attached directly over the component’s
IR receiver. To locate the IR receiver, shine a flashlight into the unit and look for the sensor.
And the emitter repeats the IR signal
CD player in front of the component.
Specifications: (typical)
Power Supply Voltage:
IR Freq. range supported:
IR pickup range:
8 - 12 VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
IR receiver head dimensions:
IR emitter outputs:
Color:
0.65” x 0.35” x 0.25”
4
Black
Specifications subject to change without notice.
Directivity of IR Sensor
The effective receive distance of all IR receivers changes when the IR remote control is not directly in front of the IR sensor.
The graph below describes the performance of the IR sensor device used in this Channel Vision IR receiver. Please note that the graph below marks the distance as a percentage of the maximum distance. So at 0º, the distance is 1.0 (or 100%) and at 30º, the distance is 0.7 (or 70%) and so on.
Actual transmission distances are dependent upon frequency of remote control (40kHz has max range) and luminosity of remote control (i.e. Some remotes are brighter than others.)
0º 10º 20º 30º
Under ideal conditions, ranges of >40 feet are possible.
1.0
0.9
0.8
0.7
40º
50º
60º
70º
80º
0.6
0.4
0.2
0 0.2
0.4
d rel
– Relative Transmission Distance
0.6
Power supply
1 - hole mount
2 - IR-3002 emitters
1 - tabletop mount
4 - IR emitter holsters
1 - IR receiver holster
IR receiver head
CAUTION: wire.
Doing
DO so
NOT will
36”
prevent the to cut unit or from extend
Features:
!
Plasma Proof IR receiver
!
!
!
4 IR emitters
Status LEDs for power and IR signal indication
Versatile mounting accessories included
LED Status indicators:
Power and IR data
DC Power input
4 IR emitter outputs
Mounting the IR emitter
CD player
Remove the backing from the tape and attach the
IR emitter holster over the IR sensor of the device you wish to control.
Snap IR emitter into the holster as shown.
Mounting the IR receiver: Option 2 - Using the hole mount
Drill a 3/4” hole .
Push the IR receiver head through the hole.
Insert the IR receiver head into the IR receiver hole mount.
Push the IR receiver hole mount and IR receiver head back into the hole.
Mounting the IR receiver: Option 1 - Using the holster
Mount the IR receiver to the TV or on a surface within line of sight of your remote control.
Remove the backing from the tape and attach the
IR receiver holster in the desired location.
Snap IR receiver head into the holster as shown.
Mounting the IR receiver: Option 3 - Using the tabletop mount
Push the IR receiver head through the hole in the tabletop mount.
Insert the IR receiver head into the IR receiver hole mount.
To secure the mount, remove the backing from the foam tape
Push the IR receiver hole mount and IR receiver head back into the hole in the tabletop mount.
on the bottom of the unit and attach the mount to any flat surface.

Public link updated
The public link to your chat has been updated.
Advertisement