Electrolux 65080 Vi Dishwasher User Manual

Favorit 65080 Vi
User manual
Dishwasher
2
Dear Customer
Thank you for choosing one of our highquality products.
With this appliance you will experience the perfect combination of functional
design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best per
formance and control indeed we are setting the highest standards of excel
lence.
In addition to this you find environmental and energy saving aspects as an inte
gral part of our products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfect
ly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a
safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
3
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips
2
Environmental information
1
Contents
3
Contents
Operating Instructions
4
Safety
4
Diagram of Appliance
5
Control Panel
6
Prior to Using for the First Time
Setting the Water Softener
Adding dishwasher Salt
Filling Up with Rinse Aid
Activating/deactivating the acoustic signal
In daily use
Loading cutlery and dishes
Adjusting the Height of the Upper Basket
Adding Detergent
Using 3 in 1 detergents
Selecting the dishwashing cycle (Cycle Table)
Starting a dishwashing cycle
Setting the Delay Timer
Switching Off the dishwasher
Care and cleaning
7
8
10
11
12
13
13
17
18
19
20
22
23
23
24
What to do if…
Remedying small malfunctions
If the dishwashing results are not satisfactory
Disposal
26
26
29
30
Technical data
30
Notes for Test Institutes
31
Installation and connection instructions
32
Safety Information for the Installation
32
Installing the Dishwasher
32
Connecting the dishwasher
Electrical Connection
Guarantee/Customer Service
33
35
36
Service and Spare Parts
39
4
Operating Instructions
Operating Instructions
1 Safety
Prior to using for the first time
• Follow the ”Instructions for installation and connection”.
Correct Use
• The dishwasher is only intended for washing domestic dishes.
• Additions or modifications to the dishwasher are not permitted.
• Use only special salt, detergent and rinse aid suitable for domestic dishwash
ers.
• Do not put any solvents in the dishwasher. This could cause an explosion.
Child Safety
• Keep packaging away from children. There is a risk of suffocation.
• Children often do not recognise the hazards associated with electrical appli
ances. Don’t allow children to use the dishwasher unsupervised.
• Make sure that children and pets don’t climb into the dishwasher. Could en
danger life!
• Dishwasher detergents can cause chemical burns to the eyes, mouth and
throat. Could endanger life! Comply with the safety instructions of the dish
washer detergent manufacturer.
• The water in the dishwasher is not for drinking. Risk of chemical burns.
General Safety
• Repairs to the dishwasher are only to be carried out by qualified/authorised
service engineers.
• When the dishwasher is not being used, switch it off and shut off the water
tap.
• Never unplug the appliance by pulling on the cable. Always pull the plug.
• Ensure that the door of the dishwasher is always closed when it is not being
loaded or unloaded. In this way you will avoid anybody tripping over the open
door and hurting themselves.
• Never sit or stand on the open door.
• If the dishwasher is located in a room where there may be a frost, remove the
connection hose from the tap after each use of the dishwasher.
Diagram of Appliance
Diagram of Appliance
Upper basket spray arm
and lower spray arm
Water softener
unit.
Salt Container
Detergent
Dispenser
Rinse aid
dispenser
Control panel
Rating plate
Filters
5
6
Control Panel
Control Panel
To use the appliance, always open the dishwasher door first.
ON/OFF button
The ON/OFF button is used to turn the dishwasher on and off.
Set delay
timer
1
Multidisplay
Programme buttons
2
Function buttons
3
Control
indicators
The Programme buttons are used to select the desired dishwashing cycle.
Prior to Using for the First Time
7
Function buttons: In addition to the preset dishwashing cycle, the following
functions can also be set using these buttons:
Function button 1
Sets the water softener
Function button 2
not programmed Function button 3
Activates/deactivates the acoustic signal
The multidisplay can indicate:
– the level of hardness to which the water softener is set.
– whether the acoustic signal has been activated/deactivated.
– the start delay that has been set.
– the estimated time remaining for the current dishwashing cycle.
– what type of error has occurred with the dishwasher.
The control indicators have the following meanings:
1)
Refill with dishwasher salt
1)
Refill with rinse aid
Turn on the tap
1) These control indicators are never illuminated while a dishwashing cycle is running.
Prior to Using for the First Time
3
If you wish to use 3 in 1 detergent:
– First read the section “Using 3 in 1 detergents”.
– Do not fill up with special salt or rinse aid.
If you do not use 3 in 1 detergent, before using for the first time
1. Set the water softener
2. Fill up with dishwasher salt
3. Fill up with rinse aid
8
Prior to Using for the First Time
Setting the Water Softener
3
The water softener must be set manually and electronically:
To avoid scale deposits on the dishes and in the dishwasher, the dishes must be
washed with soft water, i.e. water with a low lime content. The water softener
must be set according to the table to the water hardness in the area where you
live. Your local water company will be able to give you information about the
water hardness in your area.
The dishwasher must be switched off.
Setting manually:
1. Open the dishwasher door.
2. Remove the lower basket from the
dishwasher.
3. Turn water hardness dial on the left wall of
the dishwasher interior to 1 or 2 (see table).
3
Setting electronically:
1. Press the ON/OFF button.
If the LED indicator of only one programme button is illuminated, this wash pro
gramme has been activated. The wash programme must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected will illumi
nate.
2. Press function buttons 2 and 3 simultaneously and hold them down.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 1.
The LED indicator for function button 1 will flash.
The multidisplay will indicate the hardness setting.
4. Pressing function button 1 increases the hardness setting by 1.
(Exception: hardness setting 1 follows hardness setting 10).
5. When the hardness setting is correct, press the ON/OFF button.
The hardness setting is now saved.
If the water softener is set electronically to “1”, this switches off the control in
dicator for dishwasher salt.
9
Prior to Using for the First Time
Setting for
water hardness
Water hardness
in
°d 2)
in
mmol/l 3)
51 70
43 50
37 42
29 36
23 28
9,0 12,5
7,6 8,9
6,5 7,5
5,1 6,4
4,0 5,0
IV
19 22
15 18
3,3 3,9
2,6 3,2
III
5*
4
11 14
1,9 2,5
II
3
4 10
0,7 1,8
I/II
below 4
below 0.7
Range
Manual
2*
I
1
Electronic
10 4)
9
8
7
6
2
1
no salt
required
Indicator
on the multi
display
Number
of
acoustic
signals1)
10L
9L
8L
7L
6L
5L
4L
3L
2L
10
9
8
7
6
1L
1
5
4
3
2
1) The water hardness will only be indicated acoustically if the acoustic signal has been activated.
2) (°d) German degree, measure of the hardness of water
3) [mmol/l] millimol per litre, international unit for water hardness
4) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting
10
Prior to Using for the First Time
Adding dishwasher Salt
1.
2.
3.
4.
3
3
To decalcify the water softener, it must be filled up with dishwasher salt. Use
only special salt suitable for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with dishwasher salt:
– Before using the dishwasher for the first time.
– When the control indicator for dishwasher salt is illuminated on the control
panel.
Open the door and remove the lower
basket.
Unscrew the lid on the salt dispenser by
turning it anticlockwise.
Only when using the dishwasher for the
first time:
Fill the salt dispenser with water.
Place the funnel (supplied) over the dis
penser opening.
Fill the dispenser with dishwasher salt; the
capacity of the dispenser is approx. 1.01.5
kg, depending on the size of the grains. Do
not overfill the dispenser.
If water overflows when filling up with dishwasher salt, this is completely harm
less.
5. Clean away any salt remnants from the dispenser opening.
6. Screw the lid back on in a clockwise direction.
7. Run a dishwashing cycle after filling the salt dispenser with dishwasher
salt. This will wash away salt water and salt crystals that have been spilt.
Depending on the size of the salt granules, it can take several hours for the salt
to dissolve in the water and for the control indicator for dishwasher salt to go
out.
Prior to Using for the First Time
11
Filling Up with Rinse Aid
Rinse aid causes the rinse water to flow easily from the crockery leaving gleam
ing dishes and glassware.
If you do not use 3in1 detergent, fill up with rinse aid:
– Before using the dishwasher for the first time.
– When the control indicator for rinse aid is illuminated on the control panel.
Use only special rinse aid for dishwashers.
1. Open the door.
The rinse aid compartment is located on
the inside of the dishwasher door.
2. Press the release button on the rinse aid
compartment.
3. Open the cover.
4. Pour rinse aid in slowly right up to the bro
ken “max” line;
this corresponds to a volume of approx.
140 ml when full.
5. Press the lid shut until it clicks into place.
6. Wipe up any spilt rinse aid with a cloth.
Otherwise there will be too much foam
when rinsing.
12
Prior to Using for the First Time
Setting the Amount of Rinse Aid Required
3
1.
2.
3.
4.
5.
6.
Only change the amount dispensed, if smears, milky spots (reduce the amount)
or dried on water spots (increase the amount) can be seen on glasses and dishes.
(See section “If dishwashing results are not satisfactory”.) The dosage can be set
from 16. The dosage is preset to “4” in the factory.
Open the dishwasher door.
Press the release button on the rinse aid
compartment.
Open the cover.
Set the dosage level.
Press the lid shut until it clicks into place.
If rinse aid has leaked out, wipe it away
with a cloth.
Activating/deactivating the acoustic signal
3
In addition to the optical display (e.g. indicating the end of the cycle, errors) you
can also choose to set an acoustic signal.
1. Press the ON/OFF button.
If the LED indicator of only one programme button is illuminated, this wash pro
gramme has been activated. The wash programme must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 2 seconds.
The LED indicators of all the programme buttons that can be selected will illumi
nate.
2. Press function buttons 2 and 3 simultaneously and hold them down.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 3.
The LED indicator for function button 3 will flash.
The multidisplay will indicate the current setting:
0b
Acoustic signal deactivated
1b
Acoustic signal activated (factory setting)
4. Pressing function button 3 will change the setting.
5. Once the multidisplay is indicating the required setting, press the ON/OFF but
ton. The setting is now saved.
In daily use
13
In daily use
Loading cutlery and dishes
1
Sponges, cleaning cloths and any other objects that can absorb water must not
be washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to
retain water droplets. These dishes and pans therefore do not dry as well as
those made of china and stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable:
are of limited suitability:
• Only wash stoneware in the dishwasher if it is spe
• Cutlery with wooden, horn, china or
cifically marked by the manufacturer as being dish
mother of pearl handles
washersafe.
• Plastic items that are not heat re
• Glazed patterns may fade if washed very frequently
sistant
in the dishwasher.
• Older cutlery with cement
• Silver and aluminium parts have a tendency to dis
that is sensitive to temperature
colour during washing. Food remains, e.g. egg white,
• Dishes or cutlery with glued parts
egg yolk and mustard often cause discoloration and
• Pewter or copper items
staining on silver. Therefore always clean food resi
• Lead crystal glass
dues from silver immediately, if it is not to be
• Steel items that rust
washed straight after use.
• Wooden boards/platters
• Glass can become dull after a large number of wash
• Items made from synthetic materials
es.
• Before loading the dishes, you should:
– Remove the worst of the food residues.
– Soak pans with burnton food residues.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation of the spray arms.
– Load bowls, cups, glasses, pans, etc. with the opening downwards so that
water cannot collect in them
– Dishes and items of cutlery must not lie inside one another or cover one an
other
– To avoid damage to glasses, they must not touch one another
– Don’t put small items (e.g. lids) in the baskets for the dishes, but in the cut
lery basket, so that they can’t fall through the holes.
14
In daily use
Loading cutlery
1
Warning: Sharp knives and other items of cutlery with sharp edges must be laid
in the cutlery rack or in the upper basket to avoid the risk of injury.
To ensure that all items of cutlery in the cutlery basket can be reached by the
water, you should:
1.Place the grid insert on the cutlery 2.Place forks and spoons in the cutlery
basket
basket's grid insert with their han
dles pointing downwards.
For larger utensils, such as whisks, leave off one half of the cutlery grid.
The cutlery basket can be opened out.
Always make sure that you put your hand
around both parts of the twopart handle
when removing it from the dishwasher.
1. Place the cutlery basket on a table or work
surface.
2. Open out the twopart handle.
3. Remove cutlery.
In daily use
Loading / Unloading lower basket and upper basket
To load and unload, pull out or push in the
upper and lower baskets in the middle us
ing the handle on the front of the basket.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes and
pans in the lower basket.
(Max. diameter for plates 29 cm).
To make it easier to load larger dishes, the
two plate racks on the right in the lower
basket can be folded down.
15
16
In daily use
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long,
sharp cutlery in the upper basket.
• Arrange items of crockery on and under
the folding cup racks so that they are
offset from each other and water can
reach all items.
• The cup racks can be folded up out of the
way for tall crockery items.
• Lay or hang wine and brandy glasses in
the slots in the cup racks.
• For glasses with long stems, fold the
glass rack to the right, otherwise fold it
away to the left.
In daily use
• The row of spikes on the left of the upper
basket is also in two parts and can be
folded away.
Spikes not folded away: place glasses,
mugs etc. in the upper basket.
Spikes folded away: More room for serv
ing dishes.
Adjusting the Height of the Upper Basket
Maximum height of dishes in the
3
Upper basket
Lower basket
with upper basket raised
22 cm
30 cm
with upper basket lowered
24 cm
29 cm
The height of the baskets can also be adjusted when they are loaded.
Raising / Lowering the upper basket
1. Pull out the upper basket completely.
2. Holding the upper basket by the handle,
raise it as far as it will go and then lower it
vertically.
The upper basket will latch into the lower
or the upper position.
17
18
In daily use
Adding Detergent
1
3
Detergents remove the dirt from dishes and
cutlery.
The detergent must be added before the
cycle starts.
Only use detergent intended for domestic
dishwashers.
The detergent compartment is located on
the inside of the door.
1. If the lid is closed:
Press the release button.
The lid will spring open.
2. Place the detergent in the detergent dis
penser. The markings indicate the dosing
levels for powder detergents: “20/30” cor
responds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions
with regard to dosing and storage.
3. Close the lid and press until it locks into
place.
In the case of very heavily soiled dishes, fill
the adjoining compartment (1) with addi
tional detergent. This detergent comes into
use during the prewash cycle.
In daily use
19
Concentrated detergents
2
Today’s detergents for dishwashers are almost exclusively lowalkaline concen
trated detergents with natural enzymes in tablet or powder form.
Using 50°C dishwashing cycles in conjunction with these concentrated deter
gents reduces pollution and is good for your dishes, as these dishwashing cycles
are specially matched to the dirtdissolving properties of the enzymes in con
centrated detergents. It is for this reason that using 50 °C dishwashing cycles in
conjunction with concentrated detergents can achieve the same cleaning results
that can otherwise only be achieved using 65 °C cycles.
Detergent tablets
3
Detergent tablets from different manufacturers dissolve at different rates. For
this reason, some detergent tablets do not attain their full cleaning power dur
ing short cycles. Therefore please use dishwashing cycles with prewash when
using detergent tablets.
Using 3 in 1 detergents
These products are detergents with a combined cleaning, rinsing and salt func
tion.
If you want to use 3 in 1 products
1. There is no need to fill up with special salt or rinse aid.
2. Set the water softener to water hardness range “I”.
3. Set the rinse aid dosage to “1”.
Before the start of the dishwashing cycle put 3in1 detergent in the detergent
dispenser.
If you do not want to use 3 in 1 products any more
If you want to stop using 3in1 products, please do the following:
• Fill up the dispensers for salt and rinse aid again.
• Switch the water softener to the highest setting and perform up to three nor
mal cycles without loading any dishes.
• Then set the water softener to the water hardness in your area.
If you want to use 4 in 1 products
When using "4 in 1" detergents that integrate also anti glass corrosion agent
into "3 in 1" formula, please follow the same indication as given for "3 in 1" de
tergents.
20
In daily use
Selecting the dishwashing cycle (Cycle Table)
•
•
•
•
•
•
•
130 160
0,95 1,05
11 13
12
< 0,1
4
Dishes, excluding
saucepans
just used, lightly to nor
mally soiled
•
•
Used dishes that are be
ing stored in the dish
•
washer and are to be
washed later.
ECO 50°
(cold)6)
5)
Dinner service and
cookware, tempera
normally soiled
turesensitive
crockery
All types of dishes
22 24
30 MIN
(60)4)
11 22
•
9
•
1,80 2,00
normally soiled,
driedon food remains
1,1 1,6
Dinner service and
cookware
0,8
AUTO
(45° 70°)3)
120 130
•
90 125
•
30
heavily soiled,
driedon food remains,
in particular protein
and starch
Water (litres)
Drying
•
Dinner service and
cookware
Energy (kWh)
Final rinse
•
INTENSIV
CARE 70°2)
Length (minutes)
Intermediate rinse
2x
Type of
soiling
Main wash
Suitable
for:
Prewash
Dishwashing
cycle
Consumption
values1)
1 to 2x
Programme
sequence
1) The consumption values were obtained under standardised conditions. They depend on how full the bas
kets for the dishes are. Variations are therefore possible in practice.
2) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e.g. plastic chopping
boards or jam jars.
3) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The
length of the cycle and water and energy consumption can vary greatly – depending upon the load and
how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically
adjusted to between 45°C and 70°C.
4) When using this cycle, only load the dishwasher half full.
5) Test programme for Test Institutes
6) This cycle does not need any detergent.
In daily use
Selecting a programme
When your dishes look like this, select:
an intensive programme.
a normal or energysaving programme.
a short programme (e.g. 30 minute pro
gramme).
21
22
In daily use
Starting a dishwashing cycle
1.
2.
3.
4.
3
3
Check that the spray arms can turn freely.
Turn the water tap on fully.
Press the ON/OFF button.
Select the desired cycle.
The programme indicator comes on. The remaining time expected for the cycle
will be shown in the multidisplay.
During the dishwashing cycle, the remaining time shown in the multidisplay
may be adjusted according to the size of the load, degree of soiling, etc.
5. Close the door. The dishwashing cycle will begin.
A light signal in the form of a dot appears at floor level.
If the dishwasher is built in at high level with flush fitting cupboard doors
around it, the light signal cannot be seen.
The dot shaped light signal is not dangerous. (It is not a laser.) It lights up while
a dishwasher cycle is running and goes out when the cycle ends.
Interrupting or Cancelling a dishwashing cycle
1
Interrupt a dishwashing cycle that is in progress if it is absolutely necessary.
Interrupting the dishwashing programme by opening the dishwasher door
Hot steam may escape when the door is opened. There is a risk of scalding.
1. Open the door carefully. The dishwashing cycle will stop.
2. Close the door. The cycle will continue.
Cancelling the wash programme
1. Press function buttons 2 and 3 and hold them down.
The LED indicators of all the programme buttons that can be selected will illumi
nate.
2. Release the function buttons. The wash programme has been cancelled.
3. If you want to start a new wash programme, check whether there is any deter
gent in the dispenser.
In daily use
23
Setting the Delay Timer
3
With the delay timer you can delay the start of a dishwashing cycle for between
1 and 19 hours.
1. Press the Delay Timer button repeatedly until the multidisplay shows the de
sired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay
Timer indicator is illuminated.
2. Select dishwashing cycle.
3. The time remaining to the start of the cycle is continuously displayed (e. g. 12h,
11h, 10h, … 1h etc.).
To change the time delay:
As long as the cycle has not yet started, you can still change the setting by
pressing the DELAY TIMER button.
Cancelling the time delay:
Press the Delay Timer button repeatedly until the length of the selected cycle
appears in the multidisplay. The selected dishwashing cycle will begin immedi
ately.
To change a dishwashing cycle
As long as the cycle has not yet started, you can still change the dishwashing
cycle. First cancel the dishwashing cycle, then reset the time delay, lastly select
the new dishwashing cycle.
Switching Off the dishwasher
1
When the dishwasher cycle has ended, the dotshaped light signal below the
door of the appliance goes out.
If the acoustic signal has been enabled, a continuous tone will sound for 15 sec
onds at the end of the dishwashing cycle.
If the dishwasher door is not opened, the acoustic signal sounds again after 3
and 6 minutes.
Carefully open the door. Hot steam may escape.
• Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about
15 minutes before removing them. You also get a better drying result.
• Dishes dry more quickly if you open the door for a moment after the cycle has
ended and then leave it slightly open.
1. Press the ON/OFF button. All display indicators will go out.
2. Turn off the water tap.
24
Care and cleaning
Removing the Dishes
3
It is normal for the inner door and the dispensers to be damp.
• Empty the lower basket first, then the upper basket. This way you avoid drip
ping water from the upper basket onto dishes in the lower basket.
Care and cleaning
1
Do not use furniture care products or aggressive cleaners.
• When necessary, clean the dishwasher’s controls with a soft cloth.
• Occasionally check the internal dispensers, door seal and water inlet filter (if
fitted) for dirt and clean them, if necessary.
Cleaning the filters
3
The filters must be regularly checked and
cleaned. Dirty filters will spoil the wash re
sults, and may lead to malfunction of your
dishwasher.
1. Open the door and remove the lower basket.
2. Turn the handle about ¼ of a turn anticlock
wise (A) and remove the filter system (B).
3. Grasp the grip hole on the fine filter (1) and
remove it from the microfilter (2).
4. Clean all filters thoroughly under running
water.
Care and cleaning
1
5. Remove the flat filter (3) from the base of
the washing compartment and clean both
surfaces thoroughly.
6. Reinsert the flat filter.
7. Place the fine filter in the microfilter and fit
the two together.
8. Insert the filter system in place and lock it by
turning the handle clockwise as far as it will
go. Ensure that the flat filter does not pro
trude above the base of the washing com
partment.
Under no circumstances may the dishwasher be used without its filters.
25
26
What to do if…
What to do if…
Remedying small malfunctions
Before you call the Customer Care Department, please check whether
– you cannot remedy the fault yourself with the help of the following fault ta
ble
or
– whether it is caused by faulty, electrical connections and/or faulty water con
nections.
In these cases the engineer must make you liable for the costs of the Customer
Service intervention even during the warranty period.
In the event of a fault, the light signal at floor level flashes.
If the acoustic signal is activated, warning tones sound if there are faults.
If one of the following fault codes is displayed in the multidisplay during oper
ation:
– Fault codeÅ 10 (Problems with water inlet),
– Fault codeÅ 20 (Problems with water drainage),
please have a look at the following table.
When the fault is remedied, press the button for the cycle that has started. The
cycle will continue.
With other fault codes (“Å ” followed by a number):
– Abort the dishwashing cycle.
– Switch the appliance off and on again.
– Reset the dishwashing cycle.
If the fault is displayed again, please contact your local Service Force Centre and
inform them of the fault code.
What to do if…
Malfunction
1 short warning tone, con
tinuously repeated, can be
heard,
the cycle indicator for the se
lected wash program is flash
ing:
the control indicator
lights up:
fault code Å 10 is displayed
in the multidisplay:
(Problems with water inlet)
Possible cause
27
Remedy
Water tap is blocked with
limescale or is faulty.
Check the tap and have it re
paired, if necessary.
The tap is turned off.
Turn on the tap.
The filter (where present) in the
Clean the filter in the threaded
threaded hose fitting on the
hose fitting.
tap is blocked.
Cancel the dishwashing cycle
(see chapter: Starting a dish
washing cycle),
Filters in the base of the wash
clean filters (see chapter:
ing compartment are blocked.
Cleaning the filters),
then start the dishwashing cy
cle again.
Water supply hose has not
been correctly positioned.
Check the position of the hose.
2 short warning tones, con The sink outlet is blocked.
Clean the siphon.
tinuously repeated, can be
heard,
the cycle indicator for the se
lected dishwashing cycle is
Water drain hose has not been
Check the position of the hose.
flashing,
correctly positioned.
fault code Å 20 is displayed
in the multidisplay. (Prob
lems with water outflow)
3 short warning tones, con
tinuously repeated, can be
The antiflood system has been
heard,
triggered.
Fault code Å 30 is displayed
in the multidisplay.
The cycle is not starting.
First shut off the water tap,
then switch off the appliance
and contact the Customer Care
Department.
The mains plug is not plugged
in.
Connect the plug to a mains
socket.
A fuse in the house’s wiring
system is defective.
Replace fuse.
For dishwasher models with a If the dishes are to be washed
delay start timer:
immediately, cancel the delay
A start time has been selected. start.
28
What to do if…
Malfunction
Possible cause
Remedy
Rust spots are visible in the
dishwashing compartment.
The dishwashing compart
ment is made from rustfree
stainless steel. Rust spots in
the dishwashing compartment
Only wash cutlery, dishes and
are due to rust particles from
pans that are suitable for dish
external sources (rust particles
washer use.
from water pipes, pans, cutlery,
etc.). Remove such spots with a
commerciallyavailable clean
ing product for stainless steel.
A whistling noise can be
heard when washing dishes.
Decalcify appliance with com
mercially available agents for
cleaning dishwashers.
The whistling is not a cause for If the noises can still be heard
concern.
after decalcifying the machine,
use a different brand of deter
gent for washing cutlery and
dishes.
What to do if…
29
If the dishwashing results are not satisfactory
The dishes are still dirty.
• The wrong dishwashing cycle was selected.
• The dishes were loaded is such a way that the dishwashing water did not
reach all items. The baskets for the dishes must not be overloaded. The spray
arms must be free to turn.
• Filters in the floor of the dishwasher are not clean or incorrectly inserted.
• Good quality detergent was not used, or too little was used.
• In the case of scale deposits on the dishes: The special salt dispenser is empty
or the water softening system has been incorrectly set.
• The drain hose is incorrectly positioned.
• If at the end of the dishwashing cycle there is still detergent left in the deter
gent dispenser, either the spray arm was jammed or the spray arm jets are
blocked with pollutants in the dishwashing water.
You have the option of removing the spray arms from their fixture for clean
ing (see section “Care and Cleaning”).
The dishes do not dry and are not shining.
• Poor quality rinse aid was used.
• The rinse aid dispenser is empty.
There are smears, streaks, milky spots or a shiny bluish coating on glasses
and dishes.
• Lower rinse aid dosage.
There are dried water drops on the glasses and dishes.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer's cus
tomer advice centre.
Glass corrosion
• Contact the detergent manufacturer's customer advice centre.
30
Disposal
Disposal
2
Packaging material
The packaging materials are environmentally friendly and can be recycled. The
plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dis
pose of the packaging materials in the appropriate container at your local waste
disposal facilities.
2
Old appliance
W
1
The symbol
on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equip
ment. By ensuring this product is disposed of correctly, you will help prevent po
tential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you
purchased the product.
Warning! When your appliance has finished its working life, remove the plug
from the socket. Cut off the cable and plug and dispose of them.
Break the door lock so that the door no longer shuts. This prevents children from
trapping themselves inside and endangering their lives.
Technical data
5
Capacity:
12 place settings including serving dishes
Permitted water pressure:
0.11.0 MPa (= 10100 N/cm2 = 110 bar )
Electrical connection:
Also see the rating plate on the righthand side of the dishwasher’s
interior door .
Dimensions:
820 880 x 596 x 555 (H x W x D in mm)
Max. weight:
45 kg
Notes for Test Institutes
31
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the appliance
fully loaded and using the test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be carried out when the salt dis
penser in the water softener and the rinse aid dispenser have been filled with
salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).
Full load:
12 place settings including serving dishes
Amount of detergent required:
5g + 25g (Type B)
Rinse aid setting:
4 (Type III)
Example loading arrangements:
Upper basket *)
*) If there are cup racks in place on the lefthand side or the cutlery tray is in place, remove them.
Lower basket with cutlery basket*)
Cutlery basket
*) If necessary, you can remove the cup racks on the lefthand side and/or the beer glass holder.
32
Installation and connection instructions
Installation and connection instructions
1 Safety Information for the Installation
• Only transport the dishwasher in an upright position, otherwise salt water
may run out.
• Before using the dishwasher for the first time, check for any damage caused in
transport. Do not under any circumstances connect an appliance that is dam
aged. In the case of damage, please contact your supplier.
• Never use the dishwasher if the mains cable, water inlet or drain hose are
damaged; or if the control panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.
• Always plug the mains plug into a correctly installed shockproof socket.
• Prior to using the appliance for the first time, ensure that the rated voltage
and type of supply on the rating plate match that of the supply where the ap
pliance is to be installed. The fuse rating is also to be found on the rating plate.
• Multiway plugs / connectors and extension cables must not be used. This
could constitute a fire hazard through overheating.
• The dishwasher’s cable must only be replaced by a Service Force Engineer.
• A water inlet hose with safety valve must only be replaced by a Service Force
Engineer.
Installing the Dishwasher
• The dishwasher must be installed on a firm floor and adjusted to ensure that it
is stable and level in all directions.
• To compensate for unevenness in the floor and to match the height of the ap
pliance to that of surrounding units, extend the threaded feet using a screw
driver.
• Adjust the rear foot of the appliance using a cordless screwdriver from the
front of the appliance (see installation template).
• The drain hose, inlet hose and mains cable must be laid so that they are able to
move freely within the plinth area, and so that they are not kinked or crushed
when the dishwasher is in position.
• The dishwasher must also be screwed tightly to the work surface or to the ad
joining units. This is essential to ensure the dishwasher does not tip up.
Connecting the dishwasher
33
Dishwashers That Can be Integrated
(see installation template supplied)
Using the installation template supplied, split cupboard doors can be easily in
stalled and firmly fitted.
Connecting the dishwasher
Connecting to the water supply
• The dishwasher can be connected to cold or hot water supplies up to max.
60°C.
• The dishwasher must not be connected to open hot water appliances or in
stantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure:
0,1 MPa ( = 1 bar = 10 N/cm2 )
Consult your plumber if the water pressure is
less than 0,1 MPa
Highest permitted water pressure:
1 MPa ( = 10 bar = 100 N/cm2 )
If the water pressure is greater than
1 MPa, a pressure reduction valve must be used
(available from your dealer).
Connecting the inlet hose
1
3
The water inlet hose must not be kinked, crushed or entangled when it is being
connected.
Connect the threaded hose fitting (ISO 2281:2000) on the water inlet hose to a
tap with an external thread (¾ inch). The inlet hose is fitted with either a plastic
or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make sure that the tap is not drip
ping.)
So that access to the tap in the kitchen is not restricted by the use of the dish
washer, we recommend installing an additional tap, or fitting a Tbranch to the
existing tap.
34
1
Connecting the dishwasher
WARNING! Dangerous voltage
(This does apply to dishwashers with safety
valve).
The electrical cable for the safety valve is in
the doublewalled water inlet hose and is
live.
Therefore do not immerse the water inlet
hose or the safety valve in water.
Water drainage
1
Drain hose
The drain hose must not be kinked, crushed or entangled.
Connecting the drain hose:
– Maximum permitted height: 1 metre.
– Minimum required height: 40 cm above the bottom edge of the appliance.
Extension hoses
• Extension hoses are available from your lo
cal Service Force Centre. To ensure that the
function of the appliance is not impeded,
the internal diameter of extension hoses
must be 19 mm.
• Extension hoses must not be laid more
than a maximum distance of 4 metres
horizontally; the maximum permitted
height for the connection for the drain
hose is then 85 cm.
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all commonly available sink outlet types.
The outer diameter of the sink outlet connection must be at least 15 mm.
• The drain hose must be fixed to the sink outlet connection using the hose clamp sup
plied.
Antiflood system
For protection from water damage, the dishwasher is equipped with a antiflood sys
tem.
In the event of a fault, the safety valve in the water inlet hose immediately interrupts
the supply of water to the appliance.
Connecting the dishwasher
35
Electrical Connection
1
Any electrical work required to install this appliance should be carried out
by a qualified electrician or competent person.
WARNING This appliance must be earthed.
The manufacturer declines any responsibility should these safety meas
ures not be observed.
Before switching on make sure the electricity supply voltage is the same as that
indicated on the appliance rating plate.
To isolate the dishwasher from the mains, remove the mains plug.
Important: The plug must still be accessible after the appliance has been in
stalled.
Changing a fuse
The appliance is supplied with a 13amp plug fitted. In the event of having to
change the fuse in the plug supplied, a 13amp ASTA approved (BS 1363A) fuse
must be used.
Green & Yellow
Should the plug need to be replaced for
any reason, proceed as described below.
The wires on the mains lead are coloured in
accordance with the following code.
Green and Yellow:
Blue:
Brown:
1
Earth
Neutral
Live
Blue
Brown
• The wire coloured green and yellow must
Cord Clamp
be connected to the terminal marked
with the letter “E“ or by the earth symbol E or coloured green and yellow.
• The wire coloured blue must be connected to the terminal “N“ or coloured
black.
• The wire coloured brown must be connected to the terminal marked “L“ or col
oured red.
• Upon completion there must be no cut, or stray strands of wire present and
the cord clamp must be secure over the outer sheath.
WARNING! A cut off plug inserted into a 13 amp socket is a serious safety
(shock) hazard. Ensure that, if it is necessary to cut off the plug, it is dis
posed of safely and not retained.
36
Guarantee/Customer Service
Guarantee/Customer Service
Standard guarantee conditions
We, AEGElectrolux, undertake that if within 12 months of the date of the pur
chase this AEGElectrolux appliance or any part thereof is proved to be defective
by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condi
tion that:
• The appliance has been correctly installed and used only on the electricity
supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in ac
cordance with the manufacturer’s instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tam
pered with by any person not authorised by us.
• Electrolux Service Force Centre must undertake all service work under this
guarantee
• Any appliance or defective part replaced shall become the Company’s proper
ty.
• This guarantee is in addition to your statutory and other legal rights.
Exclusions
• Damage or calls resulting from transportation, improper use or neglect, the
replacement of any light bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed
or calls to appliances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those
which are subject to rental agreements.
• Products of Electrolux manufacturer that are not marketed by Electrolux
Guarantee/Customer Service
37
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for
the period specified in the appliance guarantee or otherwise by law. If you move from one of these coun
tries to another of the countries listed below the appliance guarantee will move with you subject to the fol
lowing qualifications:
• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced
by production of a valid purchase document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in
your new country of residence for this particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred
to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used
within the home, i.e. is not used for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in force within your new country of
residence.
The provisions of this European Guarantee do not affect any of the rights granted to you by law.
www.electrolux.com
p
t
b
Albania
+35 5 4 261 450
Rr. Pjeter Bogdani Nr. 7 Tirane
Belgique/België/
Belgien
+32 2 363 04 44
Bergensesteenweg 719, 1502 Lembeek
Èeská republika
+420 2 61 12 61 12
Budìjovická 3, Praha 4, 140 21
Danmark
+45 70 11 74 00
Sjællandsgade 2, 7000 Fredericia
Deutschland
+49 180 32 26 622
Muggenhofer Str. 135, 90429 Nürnberg
Eesti
+37 2 66 50 030
Mustamäe tee 24, 10621 Tallinn
España
+34 902 11 63 88
Carretera M300, Km. 29,900
Alcalá de Henares Madrid
France
www.electrolux.fr
Great Britain
+44 8705 929 929
Addington Way, Luton, Bedfordshire
LU4 9QQ
Hellas
+30 23 10 56 19 70
4 Limnou Str., 54627 Thessaloniki
Hrvatska
+385 1 63 23 338
Slavonska avenija 3, 10000 Zagreb
Ireland
+353 1 40 90 753
Long Mile Road Dublin 12
Italia
+39 (0) 434 558500
C.so Lino Zanussi, 26 33080 Porcia (PN)
Latvija
+37 17 84 59 34
Kr. Barona iela 130/2, LV1012, Riga
Lietuva
+370 5 2780609
Ozo 10A, LT 08200 Vilnius
Luxembourg
+352 42 431 301
Rue de Bitbourg, 7, L1273 Hamm
Magyarország
+36 1 252 1773
H1142 Budapest XIV,
Erzsébet királyné útja 87
38
Guarantee/Customer Service
p
t
b
Nederland
+31 17 24 68 300
Vennootsweg 1, 2404 CG Alphen aan den Rijn
Norge
+47 81 5 30 222
Risløkkvn. 2 , 0508 Oslo
Österreich
+43 18 66 400
Herziggasse 9, 1230 Wien
Polska
+48 22 43 47 300
ul. Kolejowa 5/7, Warszawa
Portugal
+35 12 14 40 39 39
Quinta da Fonte Edificio Gonçalves Zarco Q 35
2774 518 Paço de Arcos
Romania
+40 21 451 20 30
Str. Garii Progresului 2, S4, 040671 RO
Schweiz/Suisse/
Svizzera
+41 62 88 99 111
Industriestrasse 10, CH5506 Mägenwil
Slovenija
+38 61 24 25 731
Electrolux Ljubljana d.o.o.
Gerbiceva 98, 1000 Ljubljana
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux Domáce spot
rebièe SK, Seberíniho 1, 821 03 Bratislava
Suomi
www.electrolux.fi
Sverige
+46 (0)771 76 76 76
Electrolux Service, S:t Göransgatan 143,
S105 45 Stockholm
Türkiye
+90 21 22 93 10 25
Tarlabaþý caddesi no : 35 Taksim
Istanbul
Ðîññèÿ
+7 095 937 7837
129090 Ìîñêâà, Îëèìïèéñêèé
ïðîñïåêò, 16, ÁÖ „Îëèìïèê“
Service and Spare Parts
39
Service and Spare Parts
If the event of your appliance requiring service, or if you wish to purchase spare
parts, please contact Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to the Service Force Centre cov
ering your post code area.
For the address of your local Service Force Centre and further information about
Service Force, please visit the website at
www. serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the
heading „What to do if...“
When you contact the Service Force Centre you will need to give the following
details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date.
Please note that a valid purchase receipt or
guarantee documentation is required for in
guarantee service calls.
Customer Care
For general enquiries concerning your AEG
Electrolux appliance, or for further informa
tion on AEGElectrolux products please
contact our Customer Care Department by
letter or telephone at the address below or
visit our website at www.aeg.co.uk.
For Customer Service in the Republic of
Customer Care Department
Ireland please contact us at the address be
Major Appliances
low:
AEGElectrolux
AEG/ Electrolux Group (Ire) Ltd
Domestic Appliances
Long Mile Road/ Dublin 12
Addington Way
Republic of Ireland
Luton
Tel: +353 (0) 1 4090754
Bedfordshire, LU4 9QQ
Email: service.eid@electrolux.ie
Tel: 08705 350350 (*)
(*) Calls may be recorded for training purposes
117 987 82/0-00-040407-01
Subject to change without notice
www.electrolux.com
www.aeg-electrolux.co.uk