User manual | Electrolux 727039 Dishwasher User Manual

LAVAMAT 76650 A3
User manual
Washing Machine
2
Contents
Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the
appliance.
We wish you much joy with your new appliance.
CONTENTS
OPERATING INSTRUCTIONS
3
SAFETY INFORMATION
3
General safety
3
Installation
4
Use
4
Child Safety
5
PRODUCT DESCRIPTION
5
Detergent dispenser drawer
6
CONTROL PANEL
7
TABLE OF SYMBOLS
7
Display (7)
8
Indicator pilot lights (10)
9
FIRST USE
9
PERSONALIZATION
9
Acoustic signals
9
Child safety lock
9
DAILY USE
10
Load the laundry
10
Measure out the detergent and the fabric
softener
10
Select the required programme by means of
programme selector dial (1)
11
Select the desired TEMPERATURE (Button 2)
11
Select the spin speed (SPIN Reduction) or
the RINSE HOLD option (Button 3)
12
Programme option buttons
12
Select the PREWASH option (Button 4) 12
Select the STAIN option (Button 5)
12
Select the TIME SAVING option (Button 6)
12
Select an additional rinse (EXTRA RINSE)
13
Select the START/PAUSE (Button 8)
13
Select the DELAY START (Button 9)
13
Altering an option or a running programme
14
Interrupting a programme
14
Cancelling a programme
14
Opening the door after the programme has
started
14
At the end of the programme
14
WASHING PROGRAMMES
15
HELPFUL HINTS AND TIPS
19
Sorting out the laundry
19
Temperatures
19
Before loading the laundry
19
Maximum loads
20
Laundry weights
20
Removing stains
20
Detergents and additives
21
Degrees of water hardness
21
CARE AND CLEANING
21
Descaling
22
After each wash
22
Maintenance wash
22
External cleaning
22
Detergent dispenser drawer
22
Washing drum
23
Door seal
23
Drain pump
23
Cleaning the water inlet filters
25
Frost precautions
26
Emergency emptying out
26
WHAT TO DO IF…
26
TECHNICAL DATA
30
CONSUMPTION VALUES
30
INSTALLATION INSTRUCTIONS
31
INSTALLATION
31
Unpacking
31
Safety information
Positioning and levelling
Water inlet
Water-stop device
Water drainage
ELECTRICAL CONNECTION
33
33
35
35
36
ENVIRONMENT CONCERNS
Packaging materials
Ecological hints
3
36
37
37
Subject to change without notice
OPERATING INSTRUCTIONS
SAFETY INFORMATION
Read carefully & keep for future reference.
• The safety of Your appliance complies with the industry standards and with legal requirements on the safety of appliances. However, as manufacturers, we feel it is our duty
to provide the following safety notes.
• It is most important that this instruction book should be retained with the appliance for
future reference. Should the appliance be sold or transferred to another owner, or should
you move house and leave the appliance, always ensure that the book is supplied with
the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings.
• You MUST read them carefully before installing or using the appliance.
• Before first starting up, check the appliance for any damage incurred during transport.
Never connect up a damaged appliance . If parts are damaged, contact your supplier.
• If the appliance is delivered in the winter months when there are minus temperatures.
Store it at room temperature for 24 hours before using for the first time.
132940590-A-422010
General safety
• It is dangerous to alter the specifications or attempt to modify this product in any way.
• During high temperature wash programmes the door glass may get hot. Do not touch it!
• Make sure that small pets and children do not climb into the drum. To avoid this, please
check into the drum before using.
• Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine.
• Only use the advised quantities of fabric softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the manufacturer’s recommendations of quantities.
• Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case
as it is possible for such items to slip down between the tub and the inner drum.
• Do not use your washing machine to wash articles with whalebones, material without
hems or torn material.
• Always unplug the appliance and turn off the water supply after use, cleaning and maintenance.
4
Safety information
• Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced people may cause injury or serious malfunctioning. Contact
your local Service Centre. Always insist on genuine spare parts.
Installation
• This appliance is heavy. Care should be taken when moving it.
• When unpacking the appliance, check that it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing and transit bolts must be removed before use. Serious damage can occur to
the product and to property if this is not adhered to. See relevant section in the user
manual.
• After having installed the appliance, check that it is not standing on the inlet and drain
hose and the worktop is not pressing the electrical supply cable against the wall.
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air
to circulate freely under the appliance.
• Always be sure, that there is no water leakage from hoses and their connections after the
installation.
• If the appliance is installed in a location subject to frost, please read the “dangers of
freezing” chapter.
• Any plumbing work required to install this appliance should be carried out by a qualified
plumber or competent person.
• Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.
Use
• This appliance is designed for domestic use. It must not be used for purposes other than
those for which it was designed.
• Only wash and dry fabrics which are designed to be machine washed or dried. Follow the
instructions on each garment label
• Do not overload the appliance. See the Washing Programme Table.
• Before washing, ensure that all pockets are empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass
before washing. Underwired bras must NOT be machine washed.
• Garments which have been in contact with volatile petroleum products should not be
machine washed. If volatile cleaning fluids are used, care should be taken to ensure that
the fluid is removed from the garment before placing in the machine.
• As some duvets and eiderdowns should be washed/dried in large commercial machines
because of their bulk, please check with the manufacturer of the item before washing in
a domestic machine.
• The users should always check that they have not left their gas lighters (disposable or
otherwise) in their clothing.
• Never tumble dry items that have had contact with chemicals such as dry cleaning fluid.
These are of a volatile nature and could cause an explosion. Only tumble dry items which
have been washed in water or require airing.
• Plastic detergent dispensers should not remain in the drum during the drying cycle, as
the plastic used is not designed to withstand the heat. If you wish to wash-through-todry you should use the conventional detergent dispenser drawer.
Product description
5
• Never pull the power supply cable to remove the plug from the socket; always take hold
of the plug itself.
• Never use your new appliance if the power supply cable, the control panel, the working
surface or the base are damaged so that the inside of the appliance is accessible.
Child Safety
• This appliance is not intended for use by person (including children) with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• The packaging components (e.g. plastic film, polystyrene) can be dangerous to children danger of suffocation! Keep them out of children's reach.
• Keep all detergents in a safe place out of children’s reach.
• Make sure that children or pets do not climb
inside the drum. To prevent children or pets
becoming trapped inside the drum the machine incorporates a special feature. To activate this device, rotate the button (without
pressing it) inside the door clockwise until
the groove is horizontal. If necessary use a
coin. To disable this device and restore the
possibility of closing the door, rotate the
button anticlockwise until the groove is vertical.
PRODUCT DESCRIPTION
Your new appliance meets all modern requirements for effective treatment of laundry with
low water, energy and detergent consumption.
The NEW JET system allows total use of detergent and reduces water consumption so saving energy.
6
Product description
2
1
3
4
5
6
1
2
3
4
5
6
Detergent dispenser drawer
Control panel
Door opening handle
Rating plate
Drain pump
Adjustable feet
Detergent dispenser drawer
Compartment for detergent used for prewash. The prewash detergent is added at the
beginning of the wash programme.
Compartment for powder or liquid detergent used for main wash.
Compartment for liquid additives (fabric softener, starch).
Compartment for stain remover used for main wash with STAIN-option.
Control panel
7
CONTROL PANEL
Below is a picture of the control panel. It shows the programme selector dial as well as the
buttons and the display. These are presented by relevant numbers on the following pages.
1
1
2
3
4
5
6
7
8
9
10
2
3
4
5
6
7
Programme selector dial
SPIN reduction button (CENTRIFUGEREN)
PREWASH button (VOORWAS)
STAIN button (VLEKKEN PLUS)
SENSITIVE button (BEHOEDZAAM)
TIME SAVING button (TIJD)
Display
START/PAUSE button (START/PAUZE)
DELAY START button (STARTUITSTEL)
Indicator pilot lights
TABLE OF SYMBOLS
= Handwash
= Rinse Hold
= Cold
= Child Lock
8
9 10
8
Display (7)
7.1
7.2
7.3
7.5
7.4
7.1 Child safety lock symbol
7.2
• Duration of selected programme: after selecting a programme, the duration is displayed in hours and minutes (for example 2.05). The duration is calculated automatically
on the basis of the maximum recommended load for each type of fabric. After the programme has started, the time remaining is updated every minute.
• Alarm codes: in the event of operating problems, some alarm codes can be displayed,
for example E20 (see chapter «What to do if...»).
• End of programme: when the programme has finished a blinking zero is displayed,
the symbol 7.5 (Door locked) disappears on the display, the pilot light of button 8 goes
out and the door can be opened.
• Incorrect option selection: if an option which is not compatible with the set wash programme is selected, the message Err is displayed for a few seconds and the yellow pilot
light of button 8 light starts blinking.
• Delay Start: the selected delay (20 hours max) set by the relevant button appears on the
display for a few seconds, then the duration of the previously selected programme is displayed. The symbol 7.3 will appear on the display. The delay time value decreases by one
unit every hour. When only 1 hour remains, the time decreases every minute.
7.3 Delay Start - symbol
7.4 Programme progress display: the display shows the different washing programme
phases. After the appliance starts operating, the display show the relevant symbol of the
= RINSING, = DRAINING, =
washing phase which is running: = WASHING,
SPINNING - symbols
7.5 Door lock symbol
This symbol indicates if the door can be opened:
• symbol on: the door cannot be opened. The appliance is running or the appliance has
stopped with water left in the tub.
• symbol off: the door can be opened. The washing programme is finished.
9
Indicator pilot lights (10)
If the OVERDOSAGE (OVERDOSERING) pilot
light10.1 illuminates at the end of the programme, it indicates that too much detergent has
been used.
When the appliance is performing additional rinses the EXTRA RINSE (EXTRA SPOELEN) pilot light
10.2 illuminates. To add an additional rinse,
please see chapter «Select an additional rinse».
FIRST USE
• Ensure that the electrical and water connections comply with the installation instructions.
• Remove the polystyrene block and any material from the drum.
• Before the first wash, run a cotton cycle at the highest temperature without any laundry
in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a
measure of detergent into the main wash compartment and start the machine.
PERSONALIZATION
Acoustic signals
The machine is provided with an acoustic device, which sounds in the following cases:
• at the end of the cycle
• in the event of operating problems.
By pressing the 3 and 4 buttons simultaneously for about 6 seconds, the acoustic signal is
deactivated (except for the events of operating problems). By pressing these 2 buttons
again, the acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appliance unattended and not to worry that children
might be injured by or cause damage to the appliance.
This function remains able also when the washing machine is not working.
There are two different ways to set this option:
• Before pressing button 8: it will be impossible to start the machine.
• after pressing button 8: it will be impossible to change any other programme or option.
To enable or disable this option press simultaneously for about 6 seconds buttons 4 and 5
until the symbol 7.1 appears or disappears on or from the display.
10
Daily use
DAILY USE
Load the laundry
1. Open the door by carefully pulling the
door handle outwards. Place the laundry
in the drum, one item at a time, shaking
them out as much as possible.
2. Close firmly the door. You must hear a
click during closing.
WARNING!
Do not embed the laundry between the door
and the rubber joint.
Measure out the detergent and the fabric softener
Your new appliance was designed to reduce water, energy and detergent consumption.
1. Pull out the dispenser drawer until it
stops. Measure out the amount of detergent required, pour it into the main wash
compartment and, if you wish to carry
out the prewash phase, pour the detergent into the compartment marked .
If you wish to perform the stain function,
pour the stain remover into the compartment marked with an arrow.
Daily use
11
2. If required, pour fabric softener into the
compartment marked (the amount
used must not exceed the MAX mark in
the drawer).
Close the drawer gently.
Select the required programme by means of programme selector dial (1)
You can choose the right programme for any type of laundry following the descriptions on
the washing programme tables (see «Washing Programmes»).
Turn the programme selector dial to the required programme. The programme selector determines the type of washing cycle (e.g. water level, drum movement, number of rinses) and
the washing temperature according to the type of laundry.
The pilot light of button 8 starts blinking.
the proThe selector dial can be turned either clockwise or anticlockwise. On position
gramme is reset and the machine is switched off.
, to
At the end of the programme the selector dial must be turned to position
switch the machine off.
If you turn the programme selector dial to another programme when the machine is working, the yellow pilot light of button 8 will blink 3 times and the message Err is displayed on
the display to indicate a wrong selection. The machine will not perform the new selected
programme.
Select the desired TEMPERATURE (Button 2)
When selecting a programme, the appliance automatically proposes the default temperature provided for that programme.
Press this button repeatedly to increase or decrease the temperature, if you want your
laundry to be washed at a temperature different from the one proposed by the washing
machine.
By selecting position (Cold) the machine will wash with cold water. To be used for extremely delicate items, such as curtains.
For the maximum and the minimum available wash water temperature, see «Washing programmes».
12
Daily use
Select the spin speed (SPIN Reduction) or the RINSE HOLD option (Button 3)
When the required programme has been selected, your appliance automatically proposes
the maximum spin speed provided for that programme.
Press this button repeatedly to change the spin speed, if you want your laundry to be spun
at a speed different from the one proposed by the washing machine. The relevant light will
light up.
RINSE HOLD : by selecting this option the water of the last rinse is not emptied out to
prevent the fabrics from creasing. When the programme has finished the display shows a
blinking , the symbol 7.5 appears on the display and the pilot light of button8 is off. The
door is locked to indicate that the water must be emptied out.
To empty the water out please read chapter «At the end of the programme».
Programme option buttons
Depending on the programme, different functions can be combined. These must be selected
after choosing the desired programme and before pressing the button 8.
When these buttons are pressed, the corresponding pilot lights come on. When they are
pressed again, the pilot lights go out.
If an incorrect option is selected, the in yellow pilot light of the button 8 blinks for 3 times
and the Err message appears on the display for some seconds.
For the compatibility among the washing programmes and the options see chapter «Washing Programmes».
Select the PREWASH option (Button 4)
Select this option if you wish your laundry to be prewashed at 30°C before the main wash.
The Prewash ends with a short spin in programmes for cotton and synthetic fabrics, whereas in the programmes for delicate fabrics the water is only drained.
The relevant light will light up.
Select the STAIN option (Button 5)
Select this option to treat heavily soiled or stained laundry with stain remover (extended
main wash with time optimized stain action phase). The relevant light will light up.
This option is not available with a temperature lower than 40°C.
If you wish to perform a programme with the stain option, pour stain remover into stain
compartment marked with an arrow.
Select the TIME SAVING option (Button 6)
This option allows you to modify the washing time, automatically proposed by the appliance.
DAILY: by pressing button 6 once, the relative pilot light comes on and the washing duration will be reduced to wash daily soiled laundry.
SUPER QUICK: by pressing button 6 twice the relative pilot light remains lit, the washing
duration will be reduced to wash lightly soiled laundry or items that have been used or
worn for a short time. On the display will be visualized the decreased washing time.
Daily use
13
Select an additional rinse (EXTRA RINSE)
This appliance is designed for saving water. However, for people with a very delicate skin
(allergic to detergents) it may be necessary to rinse the laundry using an extra quantity of
water.
Press simultaneously buttons 2 and 3 for some seconds: the pilot light 10.2 comes on. This
function stays permanently on. To remove it press the same buttons again until the pilot
light 10.2 goes off.
Select the START/PAUSE (Button 8)
To start the selected programme, press the button 8, the corresponding red pilot light stops
blinking.
The symbols 7.4 and 7.5 appear on the display to indicate that the appliance starts operating and that the door is locked.
To interrupt a programme which is running, press the button 8: the corresponding red pilot
light starts blinking.
To restart the programme from the point at which it was interrupted, press the button 8
again. If you have chosen a delayed start with button 9, the machine will begin the countdown. If an incorrect option is selected, the yellow pilot light of the button 8 blinks for 3
times the message Err is displayed for about a few seconds.
Select the DELAY START (Button 9)
Before you start the programme, if you wish to delay the start, press the button repeatedly, to select the desired delay.
The selected delay time value (up to 20 hours) will appear on the display for a few seconds,
then the duration of the programme will appear again.
You must select this option after you have set the programme and before you press the
button 8.
The wash programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1
hour up to a maximum of 20 hours by means of this button.
The door will be locked throughout the delay time. If you wish to add laundry in the machine during the delay time you will press button 8 to put the machine in pause. Add the
laundry, close the door and press button 8 again.
Selecting the delayed start.
• Select the programme and the required options.
• Select the delay start.
• Press button 8: the appliance starts its hourly countdown. The programme will start after
the selected delay has expired.
Cancelling the delayed start
• Set the washing machine to PAUSE by pressing the button 8;
• Press button 9 once until the symbol ’ is displayed;
• Press the button 8 again to start the programme.
The selected delay can be changed only after selecting the washing programme again.
The Delay Start can not be selected with the draining programme.
14
Daily use
Altering an option or a running programme
It is possible to change some options before the programme carries them out. Before you
make any change, you must pause the washing machine by pressing the button 8.
Changing a running programme is possible only by resetting it. Turn the programme seand then to the new programme position. Start the new programme by
lector dial to
pressing the 8 button again. The washing water in the tub will not emptied out.
Interrupting a programme
Press the button 8 to interrupt a programme which is running, the corresponding light
starts blinking. Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to
new programme.
to cancel a programme which is running. Now you can select a
Opening the door after the programme has started
When the machine is working and through the delay time, the door is locked. If, for any
reason, it is necessary to open it, set firstly the machine to pause by pressing the button 8.
If the symbol 7.5 goes off, the door can be opened.
If the symbol 7.5 stays on and the door remains locked, this means that the machine is
already heating or that the water level is too high. In this case the door can not be opened.
If you cannot open the door but you need to open it you have to switch the machine off by
turning the selector dial to . After a few minutes the door can be opened (pay attention to the water level and temperature !).
After closing the door, it is necessary to select the programme and options again and to
press button 8.
At the end of the programme
The machine stops automatically, the pilot light of button 8 and the symbol 7.5 go off. A
blinking will appear on the display. Some acoustic signals sound. The door can be opened.
If a programme or an option that ends with water left in the tub has been selected, a blinking will appear on the display, the pilot light of button 8 goes off and the door remains
locked to indicate that the water must be emptied out before opening the door.
Follow the below instructions to empty out the water:
• Turn the programme selector dial to
• Select the draining or spinning programme
• Reduce the spin speed, if needed, by pressing the relevant button
• Press button 8 to start the programme
• When the programme has finished the display shows a blinking . When the symbol 7.5
goes off, the door can be opened.
Turn the programme selector dial to to switch the machine off. Remove the laundry
from the drum and carefully check that the drum is empty. If you do not intend to carry
out another wash, close the water tap. Leave the door open to prevent the formation of
mildew and unpleasant smells.
15
Stand by : once the programme has finished after a few minutes the energy saving system
will be enabled. The brightness of the display is reduced. By pressing any button the appliance will come out of the energy saving status.
WASHING PROGRAMMES
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Fabrics Load - Type of
Laundry
Options
KATOEN
95° - Cold
Main wash - Rinses - Long spin at the maximum spin
speed
Max. load 7 kg - Reduced load 3.5 kg1)
White and coloured cotton (normally soiled items).
SPIN REDUCTION
RINSE HOLD
PREWASH 2)
STAIN 3)
EXTRA RINSE
TIME SAVING1)
HYGIËNE
60°
Main wash - Rinses - Long spin at the maximum spin
speed
Max. load 7 kg
The washing programme for white cottons. This program eliminates the micro-organisms thanks to the
washing by 60°C and an additional rinse. In this way
the action is more effective. Put into the compartment Stain a special additive for hygiene and select
the option Stain.
SPIN REDUCTION
RINSE HOLD
PREWASH2)
STAIN
40 - 60 MIX
40°
Main wash - Rinses - Long spin at the maximum spin
speed
Max. load 7 kg
White and coloured cotton This programme can be
used for laundry, which should be washed at 40°C or
60°C separately. The maximum load capacity can be
put into the drum in order to save energy and water.
The same good washing result will be obtained as for
normal programme at 60°C.
SPIN REDUCTION
RINSE HOLD
PREWASH
STAIN
EXTRA RINSE
JEANS
60° - Cold
Main wash - Rinses - Long spin at 1200 rpm
Max. load 3.5 kg
With this programme it is possible to wash items like
pants, shirts or jackets in Jeans and also jersey realized with hi-tech materials. (The Extra Rinse option will
be activated automatically).
SPIN REDUCTION
RINSE HOLD
PREWASH2)
Detergent
Compartment
16
Washing programmes
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Fabrics Load - Type of
Laundry
Options
SYNTHETICA
60° - Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load 3.5 kg - Reduced load 2 kg
Synthetic or mixed fabrics: underwear, coloured
garments, non-shrink shirts, blouses.
SPIN REDUCTION
RINSE HOLD
PREWASH2)
STAIN
TIME SAVING1)
EXTRA RINSE
STRIJKVRIJ PLUS
60° - Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load 1,5 kg
Synthetic fabrics to be gentle washed and
spun.Selecting this programme the laundry is gently
washed and spun to avoid any creasing. In this way
ironing is easier. Furthermore the machine will perform additional rinses.
SPIN REDUCTION
RINSE HOLD
PREWASH2)
EXTRA RINSE
FIJNE WAS
40° - Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load kg 3.5 - Reduced load kg 2
Delicate fabrics: acrylics, viscose, polyester.
SPIN REDUCTION
RINSE HOLD
PREWASH2)
STAIN 3)
TIME SAVING 1)
EXTRA RINSE
VISCOSE
40° - Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load kg 3,5
Special gentle programme for fabrics such a viscose,
cupro, lyocell. It performs an cleaning action more intensive than the handwash programme.
SPIN REDUCTION
RINSE HOLD
PREWASH2)
STAIN 3)
EXTRA RINSE
KORT SPOELEN
Rinses - Short spin at 1200 rpm
Max. load 7 kg
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs some rinses, followed by a final spin.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
POMPEN
Draining of water
Max. load 7 kg
For emptying out the water of the last rinse in programmes with the option selected, which ends with
water left in the tub.
Detergent
Compartment
Washing programmes
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Fabrics Load - Type of
Laundry
Options
CENTRIFUGEREN
Drain and long spin at the maximum spin speed
Max. load 7 kg
Separate spin for hand washed cotton garments and
after programmes with the option selected which
ends with water left in the tub. Before selecting this
.
programme the selector dial must be turned to
You can choose the spin speed by pressing the relevant button to adapt it to the fabrics to be spun.
SPIN REDUCTION
DEKENS
40° - 30°
Main wash - Rinses - Short spin at 800 rpm
Max. load 2 kg
Special programme for a single synthetic blanket, duvet, bedspread and so on.
SPIN REDUCTION
WOL PLUS
Handwash
40° - Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load 2 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate fabrics. Note: A single or bulky item may cause imbalance. If the appliance doesn’t perform the final spin
phase, add more items, redistribute the load manually
and then select the spinning programme.
SPIN REDUCTION
RINSE HOLD
LINGERIE
Handwash
40° - Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load 1 kg
This programme is suitable for very delicate items, as
lingerie, bras and underwear etc.
SPIN REDUCTION
RINSE HOLD
SPORTKLEDING
40° - Cold
Main wash - Rinses - Short spin at 800 rpm
Max. load 2.5 kg
Special programme for sport clothes. By selecting this
programme, we recommend that you not add any
additives.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
17
Detergent
Compartment
18
Washing programmes
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Fabrics Load - Type of
Laundry
Options
OUTDOOR
40° - Cold
Prewash - Main wash - Rinses - Short spin at 1200
rpm
Max. load 2.5 kg
Special programme is suitable for washing heavily
soiled sport items. The machine will add automatically a prewash phase before the main wash to eliminate mud stains. For this phase we recommend that
compartment
you NOT put the detergent into the
of the detergent drawer in order to wash the items
with water only.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
20 MIN. - 3 KG
30°
Main wash - Rinses - Short spin at 1200 rpm
Max. load 3 kg
This programme may be used for a quick washing of
sport items or cotton and synthetic items, lightly
soiled or worn once.
SPIN REDUCTION
KORT INTENSIEF
60° - 40°
Main wash - Rinses - Short spin at 1200 rpm
Max. load 5 kg
Quick washing programme, to be used for lightly
soiled white/fast coloured cottons and mixed fabrics.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
SUPER ECO
Cold
Main wash - Rinses - Short spin at 1200 rpm
Max. load 3 kg
Mixed fabrics (cotton and synthetic). Cold wash
programme designed for saving energy, water and
time. This programme is suitable with detergents that
becomes effective at low temperature. The detergent
must be used with the supplied or a suitable detergent dosing cap (use the amount of the detergent
recommended by detergent's manufacturer). The appliance automatically runs a short heating phase if
the water temperature is lower than 6°C only.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
Detergent
Compartment
Helpful hints and tips
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Fabrics Load - Type of
Laundry
ECO
60°
Main wash - Rinses - Long spin at the maximum spin
speed
Max. load 7 kg
White and fast coloured cotton.
This programme can be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency so saving
energy.
Options
19
Detergent
Compartment
SPIN REDUCTION
RINSE HOLD
PREWASH2)
STAIN
EXTRA RINSE
= OFF
For cancelling the programme which is running or to
switch the machine off .
1) If you select the Super Quick option by pressing button 6, we recommend that you reduce the maximum load as
indicated. Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without prewash must be selected.
3) Stain option can be selected only at the temperature of 40°C or higher.
HELPFUL HINTS AND TIPS
Sorting out the laundry
Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens.
Temperatures
95° or 90°
for normally soiled white cottons and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
60°/50°
for normally soiled, colour fast garments (e.g. shirts, night dresses,
pyjamas....) in linen, cotton or synthetic fibres and for lightly soiled
white cotton (e.g. underwear)
40°-30°- Cold
for delicate items (e.g. net curtains), mixed laundry including synthetic fibres and woollens bearing the label «pure new wool, machine washable, non-shrink»
Before loading the laundry
Never wash whites and coloureds together. Whites may lose their «whiteness» in the wash.
New coloured items may run in the first wash; they should therefore be washed separately
the first time.
Make sure that no metal objects are left in the laundry (e.g. hair clips, safety pins,
pins).
Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or detergent paste.
20
Helpful hints and tips
Treat curtains with special care. Remove hooks or tie them up in a bag or net.
Maximum loads
Recommended loads are indicated in the washing programme charts.
General rules:
• Cotton, linen: drum full but not too tightly packed;
• Synthetics: drum no more than half full;
• Delicate fabrics and woollens: drum no more than one third full.
Washing a maximum load makes the most efficient use of water and energy.
For heavily soiled laundry, reduce the load size.
Laundry weights
The following weights are indicative:
The following weights are indicative:
bathrobe
1200 g
quilt cover
700 g
man’s work shirt
600 g
sheet, man’s pyjamas
500 g
tablecloth
250 g
pillow case, towelling towel, night dress, man’s shirt
200 g
tea cloth, ladies’ briefs, napkin, blouse, men’s underpants
100 g
Removing stains
Stubborn stains may not be removed by just water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a
special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab
the stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful
with rust stains which are not recent since the cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites and fast coloureds only).
Grass: soap lightly and treat with bleach (whites and fast coloureds only).
Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Treat
any residual marks with bleach.
Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
1) do not use acetone on artificial silk
Care and cleaning
21
Ink: depending on the type of ink, moisten the fabric first with acetone1), then with acetic
acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.
Detergents and additives
Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment.
Although biodegradable, detergents contain substances which, in large quantities, can upset the delicate balance of nature.
The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.),
the colour, washing temperature and degree of soiling.
All commonly available washing machine detergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C max) and woollens
• liquid detergents, preferably for low temperature wash programmes (60°C max) for all
types of fabric, or special for woollens only.
The detergent and any additives must be placed in the appropriate compartments of the
dispenser drawer before starting the wash programme.
If using liquid detergents, a programme without prewash must be selected.
Your appliance incorporates a recirculation system which allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of hardness. Information on hardness of
the water in your area can be obtained from the relevant water supply company, or from
your local authority.
A water softener must be added when water has a medium-high degree of hardness (from
degree of hardness II). Follow the manufacturer’s instructions. The quantity of detergent
can then always be adjusted to degree of hardness I (= soft).
Level
Characteristic
Degrees of water hardness
German °dH
French °T.H.
1
soft
0-7
0-15
2
medium
8-14
16-25
3
hard
15-21
26-37
4
very hard
> 21
> 37
CARE AND CLEANING
You must DISCONNECT the appliance from the electricity supply, before you can carry out
any cleaning or maintenance work.
22
Care and cleaning
Descaling
The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according
to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits.
After each wash
Leave the door open for a while. This helps to prevent mould and stagnant smells forming
inside the appliance. Keeping the door open after a wash will also help to preserve the door
seal.
Maintenance wash
With the use of low temperature washes it is possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash programme.
• Use a normal measure of detergent, must be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance with soap and water only, and then dry thoroughly.
Do not use methylated spirits, solvents or similar products to clean the cabinet.
Detergent dispenser drawer
The detergent dispenser drawer should be cleaned regularly.
1. Remove the detergent dispenser drawer by pulling it firmly.
2. Remove the conditioner insert from the
middle compartment.
3. Clean all parts with water.
4. Put the conditioner insert in as far as it
will go, so that it is firmly in place.
5. Clean all parts of the washing machine,
especially the nozzles in the top of the
washing-in chamber, with a brush.
6. Insert the detergent dispenser drawer in
the guide rails and push it in.
Care and cleaning
23
Washing drum
Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap
water containing iron.
Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or
iron or steel wool.
1. Remove any rust deposits on the drum with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing to clean off any cleaning agent residues.
Programme: Short Cotton Programme at maximum temperature and add approx. 1/4
measuring cup of detergent.
Door seal
Check from time to time the door seal and objects
that could be trapped in the fold.
Drain pump
The pump should be inspected regularly and particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during draining due to objects such as safety pins,
coins etc. blocking the pump;
• a problem with water draining is detected (see chapter “What to do if...” for more details).
WARNING!
Before opening the pump door, switch the appliance off remove the mains plug from the
socket.
Proceed as follows:
1. Unplug the appliance.
2. If necessary wait until the water has cooled down.
3. Open the pump door.
4. Pull flap forward to remove.
5. Place a container close to the pump to
collect any spillage.
24
Care and cleaning
6.
Pull out the emergency emptying hose,
place it in the container and remove its
cap.
7.
When no more water comes out, unscrew the pump cover by turning it anti-clockwise and remove the filter. Use
pliers, if necessary. Always keep a rag
nearby to dry up any water spillages
when removing the cover.
Clean the filter under a tap, to remove
any traces of fluff.
Remove foreign bodies and fluff from
the filter seat and from the pump impeller.
8.
9.
Check carefully whether the pump impeller rotates (it rotates jerkily). If it
doesn’t rotate, please contact your Service Centre.
10. Put the cap back on the emergency
emptying hose and place the latter back
in its seat.
11. Replace the filter into the pump by inserting it correctly into the special
guides. Screw the pump cover firmly by
turning it clockwise.
12. Refit the flap and close the pump door.
WARNING!
Care and cleaning
25
When the appliance is in use and depending on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When refitting the pump cover, ensure it is securely re-tightened so as to stop leaks and young children being able to remove it.
Cleaning the water inlet filters
If the appliance doesn't fill, it takes a long time to fill with water, the starting button blinks
yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..."
for more details), check if the water inlet filters are blocked .
To clean the water inlet filters:
1. Turn off the water tap.
2. Unscrew the hose from the tap.
3. Clean the filter in the hose with a stiff
brush.
4. Screw the hose back onto the tap. Make
sure the connection is tight.
5. Unscrew the hose from the machine. Keep
a towel nearby because some water may
flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
26
What to do if…
7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.
Frost precautions
If the machine is installed in a place where the temperature could drop below 0°C, proceed
as follows:
1. close the water tap and unscrew the water inlet hose from the tap;
2. place the end of the emergency emptying hose and that of the inlet hose in a bowl
placed on the floor and let water drain out;
3. screw the water inlet hose back on and reposition the emergency emptying hose after
having put the cap on again.
By doing this, any water remaining in the machine is removed, avoiding ice forming and
consequently damage to the appliance.
When you use the machine again, make sure that the ambient temperature is above 0°C.
Emergency emptying out
If the water is not discharged, proceed as follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has cooled down;
4. open the pump door;
5. place a bowl on the floor and place the end of the emergency emptying hose into the
bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl
is full, put the cap back on the hose. Empty the bowl. Repeat the procedure until water
stops flowing out;
6. clean the pump if necessary as previously described;
7. replace the emergency emptying hose in its seat after having plugged it;
8. screw the pump again and close the door.
WHAT TO DO IF…
Certain problems are due to lack of simple maintenance or oversights, which can be solved
easily without calling out an engineer. Before contacting your local Service Centre, please
carry out the checks listed below.
What to do if…
27
During machine operation it is possible that the yellow pilot light of button 8 blinks, one of
the following alarm codes appears on the display and at the same time some acoustic signals sound every 20 seconds to indicate that the machine is not working:
: problem with the water supply
•
: problem with the water draining
•
: door open
•
: anti-flooding system has activated
•
Once the problem has been eliminated, press the button 8 to restart the programme. If after all checks, the problem persists, contact your local Service Centre.
Problem
Possible cause/Solution
The washing machine does not start:
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power
socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse in your house has blown.
• Replace the fuse.
The selector dial is not correctly positioned and
the button 8 has not been pressed.
• Please turn the selector dial and press the
button 8 again.
The delay start has been selected.
• If the laundry is to be washed immediately,
cancel the delay start.
The Child safety lock has been activated.
• Deactivate this device.
The machine does not fill:
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked.
• Clean the water inlet filters (see "Cleaning
the water inlet filters" for more details).
The door is not properly closed.
• Close the door firmly.
The machine fills then empties immediately:
The end of the drain hose is too low.
• Refer to relevant paragraph in «Water drainage» section.
28
What to do if…
Problem
Possible cause/Solution
The machine does not empty and/or does not
spin:
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
• Clean the drain filter.
An option or a programme that ends with the
water still in the tub or a that eliminates all the
spinning phases has been selected.
• Select the draining or the spinning programme.
The laundry is not evenly distributed in the
drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of
the inlet hose fittings. It is not always easy to
see this as the water runs down the hose; check
to see if it is damp.
• Check the water inlet hose connection.
The drain or the inlet hose is damaged.
• Replace it with a new one.
The cap on the emergency emptying hose has
not been replaced or the filter has not been
properly screwed in after cleaning action.
• Refit the cap on the emergency emptying
hose or screw the filter fully in.
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has
been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to
washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the symbol 7.5 has gone off.
There is water in the drum.
• Select drain or spin programme to empty out
the water.
What to do if…
Problem
29
Possible cause/Solution
The machine vibrates or is noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the
drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the machine does not
spin:
The electronic unbalance detection device has
cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed
by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after
some minutes, the laundry is still not evenly
distributed in the drum, the machine will not
spin.
• The laundry load is perhaps to little, add
more items, redistribute the load manually
and then select the spinning programme.
The machine makes an unusual noise:
The machine is fitted with a type of motor
which makes an unusual noise compared with
other traditional motors. This new motor ensures a softer start and more even distribution
of the laundry in the drum when spinning, as
well as increased stability of the machine.
No water is visible in the drum:
Machines based on modern technology operate
very economically using very little water without affecting performance.
The display shows the alarm code
:
Anti-flooding system has activated.
• Disconnect the appliance, close the water tap
and contact the Service Force Centre.
30
Technical data
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and purchase date of your machine: the Service Centre
will require this information.
TECHNICAL DATA
Dimensions
Width
Height
Depth
60 cm
85 cm
60 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Cotton
7 kg
Spin Speed
Maximum
1600 rpm
CONSUMPTION VALUES
Programme
Energy consumption
(KWh)
Water consumption
(litres)
White Cottons 95°
2.10
62
Cottons 60°
1.35
58
Cotton Energy Saving
Programme 60° 1)
0.91
45
Cottons 40°
0.75
58
Synthetics 40°
0.55
51
Delicates 40°
0.55
63
Wool/ Handwash 30°
0.25
62
Programme duration
(Minutes)
For the duration of
the programmes,
please refer to the
display on the control panel.
1) «Cotton Energy Saving programme » at 60°C with a load of 8 kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
Installation
31
The consumption data shown on this chart is to be considered purely indicative, as it may
vary depending on the quantity and type of laundry, on the inlet water temperature and on
the ambient temperature.
INSTALLATION INSTRUCTIONS
INSTALLATION
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining hose from the hose holders on
the rear of the appliance.
32
Installation
3. Unscrew the three bolts using the key
supplied with the machine.
4. Slide out the relevant plastic spacers.
5. Open the porthole, take out the inlet hose
from the drum and remove the polystyrene block fitted on the door seal.
Installation
33
6. Fill the smaller upper hole and the two
large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
7. Connect the water inlet hose as described
under the paragraph «Water inlet».
Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber
coating.
Never try to correct any unevenness in the floor
by putting pieces of wood, cardboard or similar
materials under the machine.
If it is impossible to avoid positioning the machine
next to a gas cooker or coalburning stove, an insulating panel covered with aluminium foil on the
side facing the cooker or stove, must be inserted
between the two appliances.
The machine must not be installed in rooms where the temperature can drop below 0°C.
The water inlet hose and the drain hose must not be kinked.
Please ensure that when the appliance is installed, it is easily accessible for the engineer in
the event of a breakdown.
Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or
similar materials under the machine to compensate for any unevenness in the floor.
Water inlet
An inlet hose is supplied and can be found inside the machine drum.
This appliance must be connected to a cold water supply.
Do not use the hose from your previous machine to connect to the water supply.
34
Installation
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled connection to the machine.
Do not place the inlet hose downwards.
Angle the hose to the left or right depending on the position of your water tap.
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the
tap, you will have to purchase a new, longer
hose specially designed for this type of use.
Installation should comply with local water
authority and building regulations requirements. Check the minimum water pressure required for safe operation of the appliance in
the chapter "Technical Data".
Installation
35
Water-stop device
The inlet hose is provided with a water stop device, which protects against damage caused by
water leaks in the hose which could develop due
to natural ageing of the hose. This fault is shown
by a red sector in the window «A». Should this occur, turn the water tap off and refer to your Service Centre to replace the hose.
A
Water drainage
The end of the drain hose can be positioned in three ways:
1. Hooked over the edge of a sink using the plastic hose guide supplied with the
machine.
In this case, make sure the end cannot come unhooked when the machine is emptying.
This could be done by tying it to the tap
with a piece of string or attaching it to
the wall.
2. In a sink drain pipe branch. This branch
must be above the trap so that the bend
is at least 60 cm above the ground.
3. Directly into a drain pipe at a height
of not less than 60 cm and not more than
90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter
of the drain hose.
The drain hose must not be kinked.
36
Electrical connection
The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.
ELECTRICAL CONNECTION
Information on the electrical connection is given on the rating plate on the inner edge of
the appliance door.
Check that your domestic electrical installation can take the maximum load required, also
taking into account any other appliances in use.
WARNING!
Connect the machine to an earthed socket.
WARNING!
The manufacturer does not accept any responsibility for damage or injury through
failure to comply with the above safety precaution.
WARNING!
The power supply cable must be easily accessible after installing the machine.
WARNING!
Should the appliance power supply cable need to be replaced, this must be carried
out by a Service Centre.
ENVIRONMENT CONCERNS
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
37
Packaging materials
The materials marked with the symbol are recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of them properly in appropriate collection containers.
Ecological hints
To save water, energy and to help protect the environment, we recommend that you follow
these tips:
• Normally soiled laundry may be washed without prewashing in order to save detergent,
water and time (the environment is protected too!).
• The machine works more economically if it is fully loaded.
• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can
then be washed at a lower temperature.
• Measure out detergent according to the water hardness, the degree of soiling and the
quantity of laundry being washed.
38
39
132940590-A-422010
www.aeg-electrolux.com/shop
Download PDF

advertising