Electrolux 79902G Range User Manual

79902G
Electronic gas hob
Operating instructions
GB
IE
The
The innovative features of your gas hob
Your new gas hob offers several innovative
functions that distinguish it from conventional
gas hobs.
Children safety device to prevent the
controls from being accidentally operated.
General shutdown to turn off all the
Electronic control of all functions.
burners at once for an emergency.
Touch controls to activate the hob
Safety device in case of power failure or
burner ignition failure.
functions simply by touching them with a
finger.
Electronic Timer to programme your
cooking.
Automatic reignition of the burners if
the flame is accidentally extinguished.
Residual heat indicator to advise that
the pan supports and the burners are still
hot.
2
Contents
For the User
The innovative features of your gas hob ................................................................................ 2
For your safety ................................................................................................................................... 4
Description of the hob .................................................................................................................... 6
Operating instructions .................................................................................................................... 7
Touch controls .............................................................................................................................. 7
How to light a burner ...............................................................................................................8
How to turn off a burner ......................................................................................................... 9
In case of ignition failure ........................................................................................................ 9
In case of accidental extinguishing (automatic reignition) ...................................... 10
How to turn off all the burners at once ............................................................................ 11
Burner Safety Cut-off Function ............................................................................................ 11
Hob Safety Cut-off Function .................................................................................................. 11
Protection against overheating ............................................................................................ 12
Child Safety Function ................................................................................................................ 12
The Electronic Timer ................................................................................................................... 13
How to programme a burner to switch off ...................................................................... 14
How to set the Minute Minder Function .......................................................................... 16
Safety and energy-saving advice ...............................................................................................17
Cooking Table .................................................................................................................................... 18
Cleaning and maintenance ........................................................................................................... 19
Something not working? ...............................................................................................................21
Service and Spare Parts ................................................................................................................... 23
Customer Care .................................................................................................................................... 23
Guarantee Conditions ..................................................................................................................... 24
For the installer
Instructions for the Installer ......................................................................................................... 25
Important safety requirements .................................................................................................... 26
Electrical connections ...................................................................................................................... 29
Wiring diagram ............................................................................................................................ 31
Conversion to LPG ............................................................................................................................ 32
Building In ........................................................................................................................................... 36
Installation possibilities ........................................................................................................... 38
3
For your safety
This new appliance is easy to use. Nevertheless, it is important to carefully read this booklet
before installing or using the appliance for the first time. This will allow you to obtain best
performance, avoid improper actions, use the appliance in complete safety and also respect the
environment.
If you need assistance, contact our Customer Care Department on 08705 350350.
Installation
This appliance must be installed and serviced
by a competent person as stated in the Gas
Safety ( Installation and Use) Regulations
Current Editions and the IEE Wiring
Regulations.
For appliances installed in the Republic of
Ireland please refer to NSAI-Domestic Gas
Installations I.S.813 Current Editions and the
ETCI Rules for Electrical Installations.
Installation of the appliance and connection
to the power supply must only be carried
out by QUALIFIED PERSONNEL. Before any
intervention, make sure the appliance is
DISCONNECTED from the power supply.
Ensure that air can freely circulate around
the appliance. Poor ventilation produces a
lack of oxygen.
Ensure that the gas and electrical supply
complies with the type stated on the rating
plate, located below the front edge of the
glass top.
This appliance is not connected to a
combustion products evacuation device. It
must be installed and connected in accordance
with current installation regulations. Particular
attention shall be given to the relevant
regulations regarding ventilation.
When in use a gas cooking appliance will
produce heat and moisture in the room in
which it has been installed. Ensure there is a
continuous air supply, keeping air vents in
good condition or installing a cooker hood
with a venting hose.
When using the hob for a long period time,
the ventilation should be improved, by
4
opening a window or increasing the
extractor speed.
After unpacking the appliance, make sure
the product is not damaged and that the
power cable is in perfect condition.
Otherwise, contact the dealer before
installing the appliance.
The manufacturer declines any liability
should these safety measures not be
observed.
Child Safety
This hob is designed to be operated by
adults. Do not allow children to play near or
with the hob.
It is highly recommended
to activate the child safety function every
time the hob is not operated.
The hob gets hot during use and some time
after it is switched off. The hob is supplied
with special indicators for the residual heat
(see chapter “How to light a burner”).
Children should be kept away from the
appliance until it has cooled down and the
residual heat indicators are off.
During use
This instruction booklet must be kept with
the appliance for any future reference. If the
appliance is sold or transferred to another
person, ensure the booklet is passed on to
the new user.
This hob is intended for domestic cooking
only. It is not designed for commercial or
industrial purposes.
It is dangerous to modify or try to modify
the characteristics of this product.
Keep the appliance clean. Food residuals
increase the risk of fire.
This appliance cannot be cleaned with steam
or with a steam cleaning machine.
In case of malfunctions, never attempt to
repair the appliance on your own. Repairs
carried out by unqualified persons can cause
damage and accidents. Refer to the contents
of this booklet (see chapter “Something not
working”). If you do not find the information
required, contact the nearest Service Force
Centre. Servicing of this appliance must be
carried out by an authorised Service
Engineer.
Always insist on genuine spare parts.
After using the appliance, deactivate it by
using the main ON/OFF touch control and
make sure the relevant red indicator is off.
Then, lock all the hob controls by touching
.
the “Lock” Control
When using other electrical appliances,
ensure the cable does not come into contact
with the hot surfaces of this cooking
appliance.
Environmental Information
All the materials used are environment
friendly and recyclable. Please make your
contribution to safeguarding the
environment by using the special
differentiated collection channels.
Dismantled or no longer used appliances are
not worthless waste. Through ecological
disposal, various materials used in the
production of your appliance can be
recycled.
Find out about the current possibilities of
disposal from your specialised dealer, or from
your local Council.
When disposing of an old appliance, make
it unusable, by cutting off the cable.
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
Guide to Use the instructions
The following symbols will be found in the text
to guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
Hints and Tips
Environmental Information
These instructions are only valid for countries
whose identification symbols are given on the
cover of the instruction booklet and on the
appliance.
5
Description of the hob
Timer control
zone
Semirapid
burner
Semirapid
burner
Child
Safety
Control
Auxiliary
burner
Rear left
burner
control
zone
Rapid
burner
Rear right
burner
control
zone
Front left
burner
control zone
6
Main
ON/OFF
switch
Front right
burner
control zone
Operating instructions
Before using the appliance, remove all
packaging, including the advertising
labels and any protective film.
Touch Controls
The hob is supplied with special Touch Controls.
To operate your hob, simply touch the required
control with a fingertip.
Ensure to only touch one control at a time during
use.
Here follow the symbols for the main Touch
Controls, and the relevant indicators
Main ON/OFF Touch Control
Burner
control zone
Burner Ignition Touch Control
Flame level indicators
Increasing Touch Control for the flame
level
Decreasing Touch Control for the
flame level
Residual heat indicator
7
How to light a burner
1. Touch the main ON/OFF Control
for
about 3 seconds to switch on the hob. The
red indicator above the touch control lights
up, an acoustic signal sounds and the hob
is ready to use.
2. Touch the Burner Ignition Touch Control
of the required burner. The flame level
indicators located right above the symbols
and
illuminate.
3. Within about 3 seconds, touch the
Increasing
or Decreasing
Touch
Control to light the burner.
- If touch control
is selected, the burner
automatically lights at maximum flame level
(all the flame level indicators illuminate).
8
- If touch control
is selected, the burner
automatically lights at medium flame level
(three flame level indicators illuminate).
4. To adjust the burner flame level, use the
Increasing
or Decreasing
Touch
Control.
The residual heat indicator
lights up
immediately after the burner is lit.
This means that the cooking zone is getting
hot: the indicator remains on until the pan
support and the burner have cooled down.
How to turn off a burner
1. To turn off a burner press the relevant Burner
Ignition Touch Control
. All the flame
level indicators go off.
The residual heat indicator remains on until
the pan support and the burner have cooled
down.
In case of ignition failure
The hob ignition device generates a series of
small sparks for about 6 seconds.
If the flame does not light during this period,
the gas flow to the burner is interrupted. After
3 seconds, the ignition device automatically
repeats the ignition procedure for another 6
seconds.
After three failed ignition attempts, a safety
device is set on the burner. The flame level
indicators flash.
Caution! When the safety device is set
on a burner, the burner controls cannot
be operated for about 60 seconds.
9
After 60 seconds, you can remove the safety
device on the burner by touching both the
Increasing Controls
and the Decreasing
Control
at the same time.
Then, follow the instructions given in the
paragraph “How to light a burner”.
Caution! Check that the burner cap and
crown are correctly positioned (see
diagram).
If the ignition problem persists, refer to
chapter “Something not working”.
Never use a manual spark gas-lighter if
the burner ignition device does not work
correctly. If necessary, use a match.
In case of accidental
extinguishing (automatic
reignition)
If the burner flame is accidentally extinguished
(draughts, spilling of liquids, etc.), the gas flow is
immediately interrupted.
After about 20 seconds, the ignition device
automatically repeats the ignition procedure.
Upon reignition, the burner flame is first set at
maximum level, then it is automatically adjusted
to the level set before it was accidentally
extinguished.
If three consecutive reignition attempts fail, a
safety device is set on the burner. The flame
level indicators and the residual heat indicator
flash.
Caution! When the safety device is set
on a burner, the burner controls cannot
be operated for about 60 seconds.
After 60 seconds, you can remove the safety
device on the burner by touching both the
Increasing Controls
and the Decreasing
Control
at the same time.
Then, follow the instructions given in the
paragraph “How to light a burner”.
10
Burner
Cap
Burner
crown
Spark
plug
Thermocouple
How to turn off all the
burners at once
In case of unexpected safety hazard (spilling of
liquids, children hazard, etc.), you can
immediately turn off all the hob burners at once
by touching the main ON/OFF Control
.
Burner Safety Cut-off
Function
If you leave one or more burners lit and
unattended for a long time (that is, you don’t
touch any control for at least 4 hours), each lit
burner is automatically turned off and a safety
device is set on it.
If you select the burner that doesn’t work
with the Timer Control
Code number
10 flashes in the cooking time display.
Caution! When the safety device is set
on a burner, the burner controls cannot
be operated for about 60 seconds.
After 60 seconds, you can remove the safety
device on the burner by touching both the
Increasing Controls
and the Decreasing
Control
at the same time.
Then, follow the instructions given in the
paragraph “How to light a burner”.
Hob Safety
Function
Cut-off
If no burner is on but the hob is activated (the
red indicator above the main ON/OFF touch
control
is on), the hob is automatically
switched off if no control is operated within 30
minutes.
11
Protection
overheating
against
If the hob is used intensively, e.g. several burners
at maximum level for a long time, a temperature
sensor detects possible overheating and
automatically adjusts all the lit burners to
minimum.
If the hob temperature keeps rising although
the flame level has been reduced, all the lit
burners are automatically turned off and a safety
device is set on all the four burners.
If you select all the burners with the Timer
Control
(one at a time) Code number
9 flashes in the cooking time display.
Caution! When the safety device is set
on all the burners, their controls cannot
be operated for about 60 seconds.
After the 60 seconds, you can reactivate all the
burners by touching the Increasing Control
and the Decreasing Control
of one of the
four burners at the same time.
Once the safety device has been removed, wait
until the hob has cooled down before using it
again.
Child Safety Function
To avoid children operating the hob controls, it
is possible to lock them.
1. Touch the “Lock” Control
for about 3
seconds. The red indicator next to the “Lock”
symbol
lights up and an acoustic signal
sounds.
Now all the hob controls are locked, except the
main ON/OFF Touch Control.
Any lit burner keeps operating, but cannot be
adjusted.
12
2. To unlock the hob controls, touch the “Lock”
Control
for about 3 seconds. The red
indicator next to the “Lock” symbol
off and an acoustic signal sounds.
goes
It is highly recommended to activate
the child safety function every time the
hob is not operated.
In case of a power failure, the hob stores
the children safety function setting in
the system memory. If the controls are
locked at the time of the power failure,
they will still be locked when the power
is restored.
The Electronic Timer
Your hob is supplied with an electronic timer
enabling you to programme the cooking
duration. The timer can also be used as a minute
minder, when the hob is not in use.
The hob can even be used manually, i.e.
without any programming.
The timer only operates when the hob
is switched on by means of the main ON/
OFF Control
Timer
control zone
.
Here follow the symbols in the Timer Control
Zone:
Touch Control to activate the Timer
and select a burner.
Cooking time display
Burner selection display
Increasing Touch Control for the time
setting
Decreasing Touch Control for the
time setting
13
How to programme a
burner to switch off
To programme a burner to switch off, proceed
as follows:
1. If necessary, activate the hob by touching
the main ON/OFF Control
for about 3
seconds.
2. Light the burner and adjust the flame level
using the Increasing
or Decreasing
controls (see par. “How to light a burner”).
3. Activate the Timer by touching the Timer
Control
and select the required burner
by repeatedly touching the Timer Control
.
4. Set the required cooking time touching the
Increasing
and Decreasing
Controls.
(max. time: 99 minutes).
Once the cooking time has been set, the
burner selection can no longer be
changed.
If you want to change burner, you must
set the cooking time to zero by means of
the Decreasing
control, and then
change the burner selection by touching
the Timer Control
14
.
5. The timerstarts the countdown a few
seconds after the cooking time has been set.
6. During the last ten seconds, the timer starts
beeping to advise that the cooking time is
about to end.
7. An acoustic signal sounds at the end of the
cooking time. To stop the acoustic signal,
touch the Timer Control
.
To adjust the cooking time:
or Decreasing
1. Touch the Increasing
Control or at any time to adjust the time
setting.
To cancel the time setting:
1. Touch the Decreasing
Control to set the
cooking time to zero.
It is possible to programme the switchoff of ONLY one burner at a time.
You can set the cooking time as well
when the burner is already lit.
For example, you can bring a pot of
water to the boil, then put some
vegetables, meat or pasta and
programme the required time for their
cooking.
The residual heat indicators remain on
even when the hob is off, until the burner
and the pan supports have cooled down.
15
How to set the Minute
Minder Function
You can use the timer as a simple minute minder
when none of the burners are operating.
The hob must be activated in order to use the
timer as a minute minder.
Proceed as follows:
1. If necessary, activate the hob by touching
for about 3
the main ON/OFF Control
seconds.
2. Touch the Timer Control
to activate the
timer.
3. Touch the Increasing
or Decreasing
controls to set the required time (max.
time: 99 minutes).
4. The timer begins the countdown a few
seconds after the time has been set.
5. During the last ten seconds, the timer starts
beeping to advise that the timed period is
about to end.
6. An acoustic signal sounds at the end of the
timed period. To stop the acoustic signal,
touch the Timer Control
.
To adjust the time setting:
1. Touch the Increasing
or Decreasing
Control or at any time to adjust the minute
minder setting.
To cancel the time setting:
1. Touch the Decreasing
Control to set the
minute minder to zero.
16
Safety and energy-saving advice
For a correct use of the hob
To ensure maximum burner efficiency and lower
gas consumption, you should only use pots and
pans with a flat bottom fitting the size of the
burner used (see table).
If you use a saucepan which is smaller
than the recommended size, the flame
will spread beyond the bottom of the
vessel, causing the handle to overheat.
Pots must never be placed onto the
control zones.
Always turn the flame down or off
before removing pots from the burners.
Take care when frying food in hot oil
or fat, as the overheated splashes could
easily ignite.
For an easier ignition of the burner, light
it before placing the pan on the pan
support.
Unstable or misshapen pans should not
be used on the hob as unstable pans can
cause an accident by tipping or spillage.
It is advisable to cook with lids on.
By using a pressure cooker you will obtain
further energy-saving and shorter
cooking times.
As soon as a liquid starts boiling, turn
down the flame so that it will barely keep
the liquid simmering.
Avoid cooking with potstones,
earthenware pots or cast iron plates.
Also, avoid using aluminiun foil for
protecting the top during operation.
Burner
diameter
min.
diameter
max.
Large (rapid)
Medium (semirapid)
Small (Auxiliary)
160 mm
120 mm
80 mm
240 mm
220 mm
160 mm
17
Soups
Broths
Fish
Court- bouillon
15-20 minutes
Bechamel
x
x
10 minutes
Endives
Vegetables
Meat
Frying
x
x
Peas in sauce
25-30 minutes
x
x
Provence tomatoes
15-20 minutes
x
x
Fried potatoes
x
x
Pasta
x
Steak (in pot)
x
Fried escalope
10-12 minutes
x
Chips
18-22 minutes
x
Rice pudding
35 minutes
Stewed fruit
Desserts
BURNER POWER
x
Hollandaise
Sauces
SEMI-RAPID
AUXILIARY
DISHES
Recommended
cooking time
(Where no
recommendation
is given, times
should be set
according
to your personal
requirements)
RAPID
Cooking Table
x
x
x
Pancakes
3-4 minutes
x
Chocolate
5-6 minutes
x
Custard
20-25 minutes
x
Where two burners are indicated in the table, it is recommended that you choose the burner
taking into consideration the quantity of food to be cooked.
18
Cleaning and maintenance
Before any maintenance or cleaning
can be carried out, you must
DISCONNECT the hob from the
electricity supply and wait until it has
cooled down.
This appliance cannot be cleaned with
steam or with a steam cleaning machine.
The Hob Top
Regularly wipe over the hob top using a soft cloth
well wrung out in warm water to which a little
washing up liquid has been added. Avoid the
use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick
saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that proper cleaning product is
used.
If scratches or cracks are noticed on
the glass top, immediately disconnect
the appliance from the electrical supply
to avoid the risk of electrical shock.
Then, contact your local Service Force
Centre and avoid using the appliance
until it has been repaired.
19
Pan Supports
The pan supports are dishwasher proof. If
washing them by hand, take care when drying
them as the enamelling process occasionally
leaves rough edges. If necessary, remove
stubborn stains using a paste cleaner.
The pan supports can be removed from the hob
to enable better cleaning.
To keep the pan supports in the correct position,
they are fixed on metal pins located in the back
of the hob. After cleaning the hob, ensure the
pan supports are properly placed as shown in
the diagram.
Pay attention when replacing the pan
supports in order to avoid scratching
the glass hob top.
The Burners
Frequently wash the burner caps and crowns
using hot soapy water, and remove marks with a
mild paste cleaner. A well moistened soap
impregnated steel wool pad can be used with
caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft
cloth, then place back the crown and the cap in
their correct position on the burner.
For stubborn stains, use normal non-abrasive
cleaners or specific products available on the
market. NEVER use scouring pads, steel wool or
acids for cleaning.
The ignition system
The electric ignition is obtained through a spark
plug (letter C) and a metal electrode . Keep these
components clean, to avoid difficult lighting,
and check that the burner crown holes are not
obstructed.
20
A
B
C
D
- Burner Cap
- Burner crown
- Spark plug
- Thermocouple
Something not working?
If the hob is not working correctly, please carry out the following checks before contacting your local
Service ForceCentre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault
caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
PROBLEM
THE HOB
DOESN’T
WORK
CAUSE
There are blown fuses in the
domestic electrical system.
Switches are turned off or
there is no power at the power
outlet.
fHave the fuses replaced.
The hob is not activated.
f Touch the main On/Off
.
Control
fOpen the tap.
The main gas supply tap is
closed.
fPurchase a new bottle.
The hob has overheated and a
safety device has been set on
the four burners.
fAllow the top to cool (see
par. “Protection against
overheating”).
fDeactivate the Child Safety
function (see par. “Child
Safety Function”).
The safety device has been set
on the burner due to repeated
ignition failures. The flame
level indicators and the
residual heat indicator flash.
The pan support or the burner
cap and crown were not
correctly positioned after
cleaning.
The burner crown holes are
obstructed.
The defect persists.
IT TAKES TOO LONG
TO FINISH THE
DISHES / THEY
ARE COOKED
TOO FAST.
fReset the switches.
The gas bottle is empty.
The Child Safety function has
been inadvertently activated.
A BURNER
DOESN’T
WORK
f SOLUTION
The flame level adjustment is
not appropriate.
f Wait 60 seconds, then
follow the instructions
given in chapter: “In case of
ignition failure”.
fCheck the correct position
(see par. “In case of ignition
failure”).
f Follow the instructions
given in the section
“Cleaning
and
maintenance”.
f Contact an authorized
technical assistance centre.
f See the section “How to
light a burner”
21
If after all these checks, your hob still does not
operate correctly, contact your local Service
Force Centre.
Please note that it will be necessary to provide
proof of purchase for any in-guarantee service
calls. In-guarantee customers should ensure
that the above checks have been made as the
engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
22
Service and Spare Parts
If you require spare parts or an engineer contact your local Service Force Centre by telephoning:
0870 5 929 929
Your call will be routed to your local Service Force Centre.
For the address of your local Service Force Centre and further information about Service
Force, please visit the website at www.serviceforce.co.uk
For Customer Services in the Republic of Ireland please contact us at the address below:
AEG-Electrolux
Electrolux Groupl (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel +353 (0) 1 4090 754
Email service.eid@electrolux.ie
When you contact the Service Centre, they will need the following information:
1.
Your name, address and post code.
2.
Your telephone number
3.
Clear and concise details of the fault
4.
The model and the serial number (see rating label on the back of this
instruction booklet)
5.
Date of purchase
Customer Care
For general enquiries concerning your AEG-Electrolux appliance and for further information
on AEG-Electrolux products, contact our Customer Care Department by letter or telephone
at the address below or visit our website at www.aeg.co.uk
Customer Care Department
AEG-Electrolux Domestic Appliances
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
Tel : 08705 350350*
* calls to this number may be recorded for training purposes.
23
Guarantee Conditions
Standard guarantee conditions
We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux
appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials,
we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on
condition that:
·
The appliance has been correctly installed and used only on the electricity or gas supply stated on the
rating plate.
·
The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer’s operating and maintenance instructions.
·
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any
person not authorised by us.
·
All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
·
This guarantee is in addition to your statutory and other legal rights.
·
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
·
·
·
·
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances
outside the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to
rental agreements.
Products of AEG-Electrolux manufacture which are not marketed by AEG-Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
· The guarantee starts from the date you first purchased your product.
· The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
· This guarantee relates to you and cannot be transferred to another user.
· Your new home is within the European Community (EC) or European Free Trade Area.
· The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
· The product is installed taking into account regulations in your new country.
Before you move, please contact your nearest Customer Care centre, listed below, to give them details
of your new home. They will then ensure that the local Service Organisation is aware of your move and
able to look after you and your appliances.
France
Senlis
+33 (0)3 44 62 29 29
Germany Nürnberg +49 (0)800 234 7378
Italy
Pordenone
+39 (0)800 117511
Sweden
Stockholm
+46 (0)8 672 53 60
UK
Slough
+44 (0)1753 219899
24
Instructions for the Installer
Engineers Technical Data
Gas burner power
Rapid burner (large)
2.9 kW (Natural gas 20 mbar)
Semirapid burner (medium)
2.7 (LPG 28-30/37 mbar)
1.9 kW
Auxiliary burner (small)
1.0 kW
Supply connections
Gas:
R 1/2 inch (1/2 inch male) Rear right hand corner
Electric:
230 V 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
Appliance class
3
Appliance category
II2H3+
Appliance gas supply
Natural gas G20 / 20mbar
Overall dimensions
Width
730 mm
Depth
510 mm
Cut out dimensions
Width
710 mm
Depth
470 mm
This appliance complies with the following EEC Directives:
-73/23 and 90/683 (on Low Voltage);
-89/336 (on Electromagnetic Compatibility);
-90/396 (on Gas Appliances)
-93/68 (on General Standards) and subsequent amendments.
25
Important safety requirements
This hob must be installed in accordance with
the Gas Safety (Installation and Use) Regulations
(Current Edition) and the IEE Wiring Regulations
(Current Edition).
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic Gas
Installation I.S. 813 Current Editions and the
ETCI Rules for Electrical Installations.
Provision for ventilation
Detailed recommendations are contained in the
following British Standards Codes Of Practice:
B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current
Editions.
The hob should not be installed in a bed sitting
room with a volume of less than 20 m3. If it is
installed in a room of volume less than 5 m3 an
air vent of effective area of 110 cm2 is required.
If it is installed in a room of volume between 5
m3 and 10 m3 an air vent of effective area of 50
cm2 is required, while if the volume exceeds 11
m3 no air vent is required. However, if the room
has a door which opens directly to the outside
no air vent is required even if the volume is
between 5 m3 and 11 m3.
If there are other fuel burning appliances in the
same room, B.S. 5440 Part 2 Current Edition,
should be consulted to determine the requisite
air vent requirements.
For appliances installed in the Republic of
Ireland please refer to the NSAI- Domestic Gas
Installation I.S. 813 Current Editions Table Four.
26
Location
The hob may be located in a kitchen, a kitchen/
diner or bed sitting room, but not in a bathroom
or shower room.
Before making the cut out in the worktop ensure
that the edges of the hob that are to be near
either a side or rear wall have a minimum distance
of 55 mm. between the edge of the hob and the
wall.
The minimum distance combustible material can
be fitted above the hob is 400 mm. If it is fitted
below 400 mm. a space of 50 mm. must be
allowed from the edges of the hob. The minimum
distance combustible material can be fitted
directly above the hob is 700 mm.
A minimum distance of 100 mm. must be left
between the side edges of the hob and any
adjacent cabinets or walls.
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic Gas
Installation I.S 813 Current Edition Section 7Permitted Locations of Appliance.
FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
FITTING THE GAS HOB
WITH A COOKER HOOD ABOVE
27
Connection
IMPORTANT: This hob must be installed by
a competent person to the relevant Gas
Standards.
Any gas installation must be carried out
by a competent person.
The manufacturer will not accept liability,
should the above instructions or any of
the other safety instructions
incorporated in this book be ignored.
Carry out connection to the gas supply using a
rigid metal pipe with connections conforming
to the rules in force, or with a flexible s/steel
tube conforming to the relevant rules in force,
limited to those whose max. length is 2 m. If
flexible metal tubes are used, make sure they
do not come into contact with mobile parts or
are crushed. Pay the same attention also when
an oven and top combination is provided for.
The appliance gas inlet connection is 1/2"
cylindrical threaded male. Screw the parts
together without using excessive force.
IMPORTANT: After installation, always
check the perfect tightness of all the
connections, using a soapy solution.
NEVER carry out this check with a
flame.
28
A) Gas ramp end with nut
B) Washer
C) Elbow
Electrical connections
Any electrical work required to install this
hob should be carried out by a qualified
electrician or competent person, in
accordance with the current regulations.
THIS HOB MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This hob is designed to be connected to a 230 V 50 Hz
AC electrical supply.
Before switching on, make sure the electricity
supply voltage is the same as that indicated on
the hob rating plate. The rating plate is located
on the bottom of the hob. A copy is attached on
the back cover of this book.
The hob is supplied with a 3 core flexible supply
cable incorporating a 3amp plug fitted. In the
event of having to change the fuse, a 3amp ASTA
approved (BS 1362) fuse must be used.
Should the plug need to be replaced for any
reason, the wires in the mains lead are coloured
in accordance with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
— Connect the green and yellow (earth) wire
to the terminal in the plug which is
marked with the letter 'E' or the earth
symbol
or coloured green and yellow.
— Connect the blue (neutral) wire to the
terminal in the plug which is marked with
the letter 'N' or coloured black.
— Connect the brown (live) wire to the
terminal in the plug which is marked with
the letter 'L' or coloured red.
29
Upon completion there must be no cut, or stray
strands of wire present and the cable clamp must
be secure over the outer sheath.
A cut off plug inserted into a 13 amp
socket is a serious safety (shock)
hazard. Ensure that the cut off plug is
disposed of safely.
Permanent Connection
In the case of a permanent connection, it is
necessary that you install a double pole switch
between the hob and the electricity supply
(mains), with a minimum gap of 3 mm. between
the switch contacts and of a type suitable for
the required load in compliance with the current
electric regulations.
The switch must not break the yellow and green
earth cable at any point.
Ensure that the hob supply cable does
not come into contact with surfaces
with temperatures higher than 50 deg.
C.
Supply cable replacement
The cable used to connect the hob to the
electrical supply must comply to the
specifications given below.
Min. size Cable/flex
0.75 mm2
30
Cable / flex type
Fuse
H05 V2V2-F (T90)
3A
Wiring Diagram
31
Conversion to LPG
Replacing the injectors
1. Remove the pan supports.
2. Remove the burner caps and crowns.
3. Using a 7 mm socket spanner unscrew and
remove the injectors, then replace them
with the ones required for the new type
of gas (see the table “Burner
characteristics”).
4. Reassemble the parts, following the
same procedure backwards.
5. Replace the Gas Type Label (located near
the gas supply connection) with the one
corresponding to the new type of gas. The
label is supplied in the accessories plastic
bag.
Should the feeding gas pressure be different or
variable compared with the required pressure,
an appropriate pressure regulator must be fitted
on the gas supply pipe, in compliance with the
rules in force.
Burner characteristics
GAS
TYPE
BURNER
TYPE
INJECTOR
REFERENCE
1/100 mm
NOMINAL
THERMAL
POWER
kW
REDUCED
THERMAL
POWER
kW
NOMINAL
FLOW RATE
m3/h
g/h
mbar
20
NATURAL
Rapid
GAS
Semirapid
(G 2 0 )
Auxiliary
119
96
70
2.9
1.9
1.0
0.65
0.45
0.33
0.276
0.181
0.095
-
LIQUID
GAS
(Butane/
Propane)
86
71
50
2.7
1.9
1.0
0.65
0.45
0.33
-
196
138
73
32
Rapid
Semirapid
Auxiliary
FEEDING
PRESSURE
28-30/37
Setting the hob for the new
gas type
1. If necessary, activate the hob by touching
the main ON/OFF Control
seconds.
for about 3
repeatedly to
2. Touch the Timer Control
select the auxiliary burner (front left burner)
on the burner selection display .
3. Touch the Increasing Control
and hold
the finger on it until the value 99 appears
on the time display. Then, touch the
Decrasing Control
and hold the finger
on it until the value 80 is displayed.
4. Then, touch the Increasing Control
until
83 is displayed. At this point, the hob is set
to the “Gas Change” mode and the current
gas setting appears on the display:
- n0 stands for gas G20 (20 mbar)
- n1 for gas G30 (28-30/37 mbar).
IMPORTANT: setting n2 does not allow
the hob to function.
33
4. Touch the Decreasing Control
the required type of gas.
to select
5. After selecting the type of gas, switch off
the hob touching the main ON/OFF Control
.
6. Touch the main ON/OFF Control
again
to reactivate the hob.
The appliance is automatically set to the
normal “User Mode”.
7. Light all the burners and adjust their flame
to minimum, in order to check the flame
stability (visual check).
8. At the same time, check the flame aspect
(visual check).
If both the flame stability and the flame aspect
are satisfactory, the setting of the hob for the
new gas type is completed.
If the flame stability is not satisfactory, carry out
an additional adjustment as described in the
following paragraph.
Minimum flame adjustment
If the flame stability and the flame aspect are
not satisfactory, proceed as follows:
1. Carry out the steps described in the
paragraph “Setting the hob for the new gas
type” - points 1, 2 and 3.
2. Light the burner to be adjusted following
the instructions given in the paragraph
“How to light a burner”.
The burner is automatically set to the
minimum flame level.
3. If the flame minimum level is too low, the
burner extinguishes. The hob automatically
carries out a minimum level adjustment and
then relights the burner.
34
4. While the flame is on, touch the Increasing
or Decreasing
Controls to carry
out a fine adjustment, until a small and
regular flame is obtained on the whole
burner crown.
5. Switch off the hob touching the main ON/
OFF Control
.
35
Building In
A = Auxiliary burner
SR = Semirapid burner
R = Rapid burner
Dimensions are given
in millimetres
SR
SR
R
A
Fig. 1
51
0
73
0
The hob is designed to be inserted in modular
kitchen units with depth of 550 - 600 mm and
having proper characteristics.
The building-in is also possible in modular units
with a 600 mm width: in this case, the cut-out
in the work top must be carried out as shown in
Fig. 2.
The worktop must be at least 30 mm thick.
If the worktop is thicker than 50 mm, it is
possible to install the hob on modular units of
any width.
Any unit (furniture unit, household appliance,
etc..) placed near the unit which the hob is built
in, shall not exceed the worktop height.
A minimum clearance of 100 mm
between the cut-out in the worktop
and any side wall exceeding the
worktop height must be observed.
The hob dimensions and the cut-out
dimensions are given in fig. 1 and 2.
36
A) Worktop
B) Removable Panel
Fig. 2
Fitting the hob to the worktop
Before fitting the hob into the cut out, an
adhesive seal must be fitted to the underside
outside edge of the hob. It is essential that no
gaps are left in this seal in order to prevent
spillage near the hob seeping into the cabinet
below.
Proceed as follows:
1. Remove the pan supports, the burner caps
and crowns and turn the hob upside down,
taking care that the spark plugs and the
thermocouples are not damaged in this
operation.
2. Place the sealing gasket all around the glass
top edge as shown in Fig. 3.
3. Fit the hob in the cut out and push it down
until the glass top and the worktop make
contact, as shown in Fig. 4. The side springs
ensure centering.
Fig. 3
A
A) Seal
Fig. 4
37
Installation possibilities
Building over a kitchen unit
with door
Proper arrangements must be taken in designing
the furniture unit, in order to avoid any contact
with the bottom of the hob which can be heated
when it is operated. The recommended solution
is shown in Fig. 5.
The panel fitted under the hob ("a") should be
easily removable to allow easy access if technical
assistance is needed. See also Fig. 2.
The space behind the kitchen unit ("b") can be
used for connections.
Fig. 5
Dimensions are in mm
Building over a unit with an
oven
The recesses for the hob and the oven must
comply the indication given in Figs. 6 and must
be provided with openings to allow a
continuous supply of air.
Two possible solutions to avoid excessive
overheating are described in Fig. 7 and 8.
The electrical connection for the hob and the
oven must be carried out separately, for safety
reasons and also to allow the oven to be easily
removed from the unit, if necessary.
38
a) removable panel
b) space for connections
Hanging furniture units or hoods must
be placed at 650 mm. minimum from
the hob (Fig. 6).
The electronic gas hob can only
be installed over a built-in oven
equipped with cooling fan.
If the hob is installed over a
built-in oven equipped with
pyrolytic cleaning function, the
hob must not be in use while
the pyrolytic cleaning cycle of
the oven is running.
Fig. 6
Fig. 7
Fig. 8
50 cm 2
120 cm 2
180 cm 2
360 cm 2
FO 0938
FO 0939
39
AEG Haugeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
From the Electrolux Group. The world’s No.1 choice.
35688-7301
04/05
Grafiche MDM - Forlì
The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn
mowers) are sold each year to a value of approx. USD 14 billion in more than 150
countries around the world.