Electrolux D77000 Cooktop User Manual

D77000
User Manual
Cooker
IMPORTANT SAFETY INFORMATION
This appliance is intended for cooking
purposes only. It must not be used for
other purposes, for example room heating.
The grill dor must be left open when
grilling.
This appliance is not suitable for
installation in flats or other mutli
occupancy dwellings as defined
in clause 8.2.1 of IGE/G/5.
This appliance has been designed for domestic use
to cook edible foodstuffs only and must not be used
for any other purposes.
Take great care when heating fats and oils as they
will ignite if they become too hot.
When you are lighting any burner check that it is lit
before you leave the appliance. When turning off a
burner, do not leave the appliance until the flame
has gone out.
Never place plastic or any other material which may
melt in or on the oven.
Do not leave the grill pan handle in position when
grilling as it will become hot.
Always support the grill pan when it is in the
withdrawn or partially withdrawn position.
Always use oven gloves to remove and place food
in the oven.
Ensure cooking utensils are large enough to contain
foods to prevent spillages and boil overs.
During use the appliance becomes hot. Care should
be taken to avoid touching the heating elements
inside the oven.
Ensure that all vents are not obstructed to ensure
ventilation of the oven cavity.
Never line any part of the appliance with foil.
Always stand back from the appliance when
opening the oven door to allow any build up of steam
or heat to release.
Never leave the appliance unattended when the
oven doors are open.
Do not place sealed cans or aerosols inside the
oven. They may explode if they are heated.
Ensure that all control knobs are in the OFF position
when not in use.
Do not stand on the appliance or on the open oven
doors.
Do not hang towels, dishcloths or clothes from the
appliance or its handles.
Do not use this appliance if it is in contact with
water. Never operate it with wet hands.
These warnings are provided in the interests of your
safety. Ensure that you understand them all before
installing or using the appliance. Your safety is of
paramount importance. If you are unsure about any
of the information in this book contact the Customer
Care Department.
INSTALLATION
The appliance must be installed according to the
instructions supplied. The installation work must be
undertaken by a competent person as stated in the
Gas Safety (Installation & Use) Regulations Current
Editions and the IEE Wiring Regulations.
The appliance should be serviced by an authorised
Service Engineer and only genuine approved spare
parts should be used.
It is important that the appliance is suitable for your
gas supply. Your installer should check the rating
plate.
Make sure that a stability chain is fitted.
The appliance must be installed in an adequately
ventilated room.
If the appliance is to be placed on a base, measures
must be taken to prevent the appliance from slipping
from the base.
This appliance is heavy and care must be taken
when moving it.
Do not attempt to lift or move this appliance by the
handles.
All packaging, both inside and outside the appliance
must be removed before the appliance is used.
It is dangerous to alter the specifications or modify
the appliance in any way.
After installation please dispose of the packaging
with due regard for safety and the environment.
Your local authority can arrange this.
CHILD SAFETY
CLEANING AND MAINTENANCE
Do not allow children to play with any part of the
packaging.
Do not allow children to sit or climb on the drop
down doors.
This appliance is not intended for use by children
and other persons whose physical, sensory or
mental capabilities or lack of experience and
knowledge prevents them from using the appliance
safely without supervision or instruction by a
responsible person to ensure that they can use the
appliance safely.
Children should be supervised to ensure that they do
not play with the appliance.
CAUTION: Accessible parts may be hot when the
grill is in use. Young children should be kept
away.
DURING USE
This appliance is not intended to be operated by
means of an external timer or separate remote
control system.
2
For hygiene and safety reasons this appliance
should be kept clean at all times. A build up of
fats or other foodstuffs could result in a fire,
especially in the grill pan.
Do not leave cookware containing foodstuffs, e.g. fat
or oil in the appliance in case it is inadvertently
switched on.
Do not disconnect the appliance from the gas supply
if the supply pipe does not have a bayonet
connection as described in the installation section. If
this is the case contact the person who installed the
appliance.
Always allow the appliance to cool before switching
off at the wall prior to carrying out any cleaning
/maintenance work.
Only clean this appliance in accordance with the
instructions given in this book.
Never use steam or high pressure steam cleaners to
clean the appliance.
CONTENTS
FOR THE USER
Important Safety Information
Description of the Appliance
Getting to Know Your Appliance
Before Using the Appliance
Rating Plate
Preparing to Use your Appliance
The Cooling Fan for the Controls
Control Panel Indicator Neon(s)
Condensation and Steam
Cookware
Grill and Oven Furniture
The Timer
2
4
5
6
6
6
6
6
6
6
6
7
The Hob
Using the Hob
To Light the Hob Burners
To Turn Off Any Burner
Things to Note
Hints & Tips
The Dual Grill
Using the Dual Grill
Things to Note
The Grill Pan and Handle
Hints and Tips
Grilling Chart
The Second Oven
Using the Second Oven
Things to Note
To Fit the Second Oven Shelf
Hints and Tips
Second Oven Cooking Chart
Main Oven Grill
Using Main Oven Grill
Things to Note
Hints and Tips
Grilling chart
10
10
10
10
11
11
12
12
12
12
13
13
14
14
14
14
15
16
17
17
17
17
18
Conventional Cooking
Using Conventional Cooking
Things to Note
Hints and Tips
19
19
19
20
PROFI Hot air
Using PROFI Hot air
Things To Note
To Fit The Main Oven Shelves
Hints And Tips
Oven Cooking Chart
Roasting Chart
Fan Roasting
Using Fan Roasting
Things to Note
Hints and Tips
Fan Roasting Chart
Pizza
Using Pizza
Things to Note
Hints and Tips
21
21
21
22
22
23
24
25
25
25
26
26
27
27
27
27
Bottom Heat
Using Bottom Heat
Things to Note
28
28
28
Defrost
Using Defrost
Things to Note
Hints and Tips
29
29
29
29
Care and Cleaning
30
Cleaning Materials
30
Cleaning the Outside of the Appliance
30
Cleaning the Control Knobs and Handles
30
Removing and Replacing the Wirework Runners 30
Cleaning the Hob
31
When Replacing Hotplate Burner Parts
31
Cleaning the Shelves, Wirework Runners
and Grill/Oven Furniture
31
Cleaning Inside the Grill and Oven Compartments 32
Cleaning the Door(s)
33
Replacing an Interior-Lighting Bulb
34
Something Not Working?
35
Service and Spare Parts
36
Guarantee Conditions
37
FOR THE INSTALLER
Technical Details
Important Safety Requirements
Provision For Ventilation
Moving Your Appliance
For Your Safety
Location of Appliance
Levelling the Appliance
Connecting to the Electricity Supply
Connecting to Gas Supply
Fitting the Stability Chain
Testing
General Note
Notes
38
39
39
40
40
40
40
41
42
42
42
43
44
To help you the following symbols will be found in
the text.
Hints and Tips
Safety Instructions.
Please read the instruction book carefully before
use and retain for future reference.
AT THE END OF THE APPLIANCE'S LIFE
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
3
DESCRIPTION OF THE APPLIANCE
SLIP-IN DUEL FUEL MULTIFUNCTION DOUBLE OVEN
Electronic Timer
Control Panel
Second Oven / Grill
Main Oven
4
GETTING TO KNOW YOUR APPLIANCE
THE CONTROL PANEL
A
B
C
E
D
I
J
FEATURES
A
B
C
D
E
-
Hotplate Control
Hotplate Control
Second Oven/Grill Temperature Control
Electronic Timer
Main Oven Multifunction Selector
Defrost
Bottom Heat
Pizza
Fan Roasting
PROFI Hot air
Conventional Cooking
Main Oven Grill
Interior-Lighting
F
G
H
I
J
-
F
Main Oven Temperature Control
Hotplate Control
Hotplate Control
Main Oven Indicator Neon
Second Oven/Grill Indicator Neon
5
G
H
BEFORE USING THE APPLIANCE
For your safety wall coverings at the rear of the
appliance should be securely fixed to the wall.
RATING PLATE
This is situated on the lower front frame of the
appliance and can be seen upon opening the door.
Alternatively the rating plate may also be found on the
back or top of some models (where applicable).
The appliance must be protected by a suitably rated
fuse or circuit breaker. The rating of the appliance is
given on the rating plate.
Do not remove the rating plate from the appliance
as this may invalidate the guarantee.
COOKWARE
Baking trays, dishes etc., should not be placed directly
against the grid covering the fan at the back of the
oven.
Do not use baking trays larger than 30cm x 35cm (12”
x 14”) as they will restrict the circulation of heat and
may affect performance.
PREPARING TO USE YOUR APPLIANCE
Wipe over the base of the oven(s) with a soft cloth and
hot soapy water and wash the furniture before use.
We suggest that you run the oven(s) and grill for 10 –
15 minutes at maximum temperature, to burn off any
residue from their surfaces. Accessible parts may
become hotter than in normal use. Children should be
kept away. During this period an odour may be
emitted, it is therefore advisable to open a window for
ventilation.
GRILL AND OVEN FURNITURE
The following items of grill and oven furniture have
been supplied with the appliance. If you require
replacements of any of the items listed below please
contact your local Service Force Centre, quoting the
relevant part number.
1 grill pan
(349099801)
THE COOLING FAN FOR THE CONTROLS
The cooling fan comes on immediately when the
grill/second oven is switched on and after a short time
when the main oven is in use. It may run on after the
controls are switched off until the appliance has
cooled. During the initial period the cooling fan may
turn ON and OFF, this is quite normal.
1 grill pan handle
(349100501)
Always allow the cooling fan to cool the
appliance down before switching off at the
wall prior to carrying out any cleaning or
maintenance work.
1 grill pan grid
(311757500)
CONTROL PANEL INDICATOR NEON(S)
The indicator neon will operate when the grill (where
applicable) or oven(s) is switched on. The indicator
neon will glow. It may turn on and off during use to
show that the setting is being maintained. If the neon
does not operate as the instructions indicate the
controls have been incorrectly set. Return all controls
to zero and reset following the instructions for the
required setting.
1 meat tin
CONDENSATION AND STEAM
1 cranked shelf
(for grilling and
second oven cooking)
When food is heated it produces steam similar to a
boiling kettle. The vents allow some of this steam to
escape. However, always stand back from the
appliance when opening the door(s) to allow any build
up of steam or heat to release.
If the steam comes into contact with a cool surface on
the outside of the appliance, e.g. a trim, it will
condense and produce water droplets. This is quite
normal and is not caused by a fault on the appliance.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
2 cranked shelves
(for main oven
cooking)
6
THE TIMER
KEY
A
COOK TIME
A
C
B
END TIME
B
D
C
COUNTDOWN
D
TIME
E
DECREASE CONTROL
F
SELECTOR CONTROL
G
INCREASE CONTROL
E
NOTE:
The time of day must be set before the main oven
will operate manually.
1. HOW TO SET THE TIME OF DAY
The oven has a 24 hour clock.
When the electricity supply is first switched ON, the
display will show 12.00 and the 'Time' (
) indicator
neon will flash as Fig. 1.
To set the correct time press the increase control
button ( + ) and if necessary, the decrease control
button ( - ) until the correct time on the 24 hour clock
is reached, e.g. 10.00am as Fig.2. The 'Time'
indicator neon (
) will flash for 5 seconds and then
go out.
Fig.1.
Note: The increase and decrease control buttons
operate slowly at first, and then more rapidly.
They should be pressed separately.
Fig.2.
2. HOW TO SET THE COUNTDOWN
The 'Countdown' gives an audible reminder at the
end of any period of cooking. This cooking period
may be up to 2 hrs 30 mins. It is not part of the
automatic control.
To set, press the Selector Control button (
) until
the 'Countdown' indicator neon (
) is illuminated
the display reads 0.00 as Fig.3.
Fig.3.
To set the correct time duration depress the increase
control ( + ) until the display indicates the interval to
be timed, e.g. 1hr 45 mins as Fig. 4. If necessary
depress the decrease control ( - ) to achieve the
correct time interval.
NOTE: This must be completed within 5 seconds
of first pressing the Selector Control button.
During the operation of the 'Countdown', the
remaining time period will be shown in the display.
The 'Countdown' will sound intermittently for up to 2
minutes at the end of the timed period. The sound
can be stopped by pressing any button.
Fig.4.
7
F
G
TO CANCEL THE COUNTDOWN
If you change your mind and want to cancel the
'Countdown', press the Selector Control button until
the 'Countdown' indicator neon (
) flashes and
then the decrease control ( - ) until 0.00 shows in the
display as Fig. 5. The 'Countdown' indicator neon
(
) will continue to flash for a few seconds and
then return to the time of day.
3. SETTING THE OVEN TIMER
CONTROL
Fig.5.
The main oven only can be automatically timed.
When using the timer control for the very first time, it
is advisable to let it operate while you are at home.
The displays can be checked to show that it is
operating correctly and you will feel confident to
leave a meal to cook automatically in the future.
A) TO SET THE TIMER TO SWITCH ON
AND OFF AUTOMATICALLY
i) Ensure the electricity supply is switched ON and
that the correct time of day is displayed, e.g.
9.am. as Fig. 6.
ii) Place food in the oven.
iii) To set the length of cooking time, press the
Selector control button (
) until the 'Cook Time'
indicator neon is illuminated (
). Press the
increase control ( + ) until the required length of
cooking time is displayed, e.g. 2 hrs 15 mins as
Fig. 7. If necessary depress the decrease control
( - ) until the correct time interval is achieved.
The maximum cooking time is 10 hours.
iv) Release the buttons. The 'Cook Time' indicator
neon (
) will be illuminated.
Fig.6.
Fig.7.
Remember, this must be completed within 5
seconds of first pressing the Selector Control
button.
v) To set the 'End Time'. Press the Selector Control
button until the 'End Time' indicator neon (
)
flashes. Press the increase control ( + ) until the
required stop time is displayed, e.g. 12.15 p.m. as
Fig. 8. If necessary depress the decrease control
( - ) until the correct time interval is achieved.
vi) Release the buttons. The time of day will be
displayed after 5 seconds. The 'Cook Time'
(
) and 'End Time' (
) indicator neons will be
illuminated.
The 'End Time' must not be more than 23 hours
59 minutes from the time of day. For example, if
the time of day is 09.00 a.m., the latest 'End Time'
would be 08.59 a.m. the next day.
vii) Set the main oven control to the required
temperature. The oven indicator neon should be
OFF.
Fig.8.
NOTE: When the automatic timed period starts,
the oven indicator neon will glow. It may turn on
and off during use to show that the setting is
being maintained.
8
B) TO SET THE TIMER TO SWITCH OFF
ONLY
i) Ensure the electricity supply is switched ON and
that the correct time of day is displayed, e.g.
10.00am as Fig. 9.
ii) Place food in the oven.
iii) To set the length of cooking time, press the
Selector Control button until the 'Cook Time'
(
) indicator neon is illuminated. Press the
increase control ( + ) until the required length of
cooking time is displayed, e.g. 2 hrs 15 mins as
Fig. 10. Depress the decrease control ( - ) if
necessary.
iv) Release the buttons. The 'Cook Time' indicator
neon (
) will illuminate and the time of day will
be displayed after 5 seconds.
v) Set the oven temperature. The oven indicator
neon should be ON.
vi) To check the 'End Time' during the cooking
period, simply press the Selector Control button
once and the remaining time will be displayed, as
Fig. 11.
Fig.9.
Fig.10.
4. TO CANCEL AN AUTOMATIC
PROGRAMME
i) To cancel an automatic programme press the
Selector Control button until the 'Cook Time'
indicator neon (
) flashes. Press the decrease
control ( - ) until the display reads 0.00 as Fig. 12.
ii) Release the buttons. The 'Cook Time' indicator
neon (
) will flash and after 5 seconds return
to the time of day.
iii) Turn off the oven controls.
Fig.11.
5. TO RETURN THE APPLIANCE TO
MANUAL
At the end of a timed cooking period, the indicator
neon will flash and an alarm will sound for up to 2
minutes.
i) To stop the sound press any of the three buttons,
as Fig. 13.
ii) The display will return to the time of day.
iii) Turn off the oven controls.
Fig.12.
6. THINGS TO NOTE
x
In the event of an interruption of the electricity
supply, the timer will reset itself to zero, and all
programming will be cancelled.
Fig.13.
7. AUTOMATIC COOKING
It is advisable to leave food in the oven for as
short a time as possible before automatic cooking.
Always ensure commercially prepared food is well
within its use by date and that home prepared
food is fresh and of good quality.
When cooking is complete, do not leave food to
stand in the oven, but remove and cool it quickly if
the food is not to be consumed immediately.
Always ensure food in the oven has been covered
before cooking if it is not possible to remove food
immediately after cooking.
9
THE HOB
The gas hob has different burner sizes to suit
different types of cooking:
To ensure maximum burner efficiency only use pots
and pans with flat bases appropriate to the burner
size used.
Larger burner (Rapid or triple crown where
applicable) - use a large pan for food such as chips.
Medium burners (Normal) - use for everyday
cooking.
Small burner (Simmer) - use for simmering foods
such as soups and stews.
The largest pan which you should use on any burner
is 230mm (9"). The base of the smallest pan should
not measure less than 100mm (4").
Ensure the pan supports are correctly
fitted before using the hob.
TO LIGHT THE HOB BURNERS
The hob ignition works by means of an electric spark
system.
1. Lift up the lid. You cannot use the hob when the
lid is down.
2. Push in and hold the control knob, turn to the
large flame symbol (highest setting) and press
the ignition button immediately. Keep the control
knob depressed for up to 5 seconds, but no
longer than 10 seconds. After this time release
the controls. The flame should remain alight. If
after 10 seconds the burner has not lit, stop
operating the appliance and wait at least 1 min
before attempting a further ignition of the burner.
3. When the burner has lit release the control and
ignition button, adjust the setting as required.
Warning: If the ignition button is not
pressed immediately a build up of gas
may cause the flame to spread.
If you close the lid of the appliance while
any of the hotplate burners are lit, the gas
will go out. This is because it would be
dangerous if the burners stayed on when
the lid was closed.
Always use the control knob to turn off a
burner. Do not use the lid as a cut-off
device. This will only cut off the gas
when the lid is closed. The gas will flow
again when the lid is opened.
10
TO TURN OFF ANY BURNER
1. Turn the control knob to the off position.
When lighting any burner, ensure that it
is lit before you leave the appliance.
When turning off a burner, ensure the
flame has gone out before leaving the
appliance.
In the event of the burner flames being
accidentally extinguished, turn off the
burner control and do not attempt to reignite the burner for at least 1 min.
THINGS TO NOTE
If you are having any difficulty lighting a hob burner
turn all the hob controls off and make sure the
burner parts have been replaced correctly.
x
x
x
HINTS AND TIPS
Do not overfill pans or they will boil over.
Do not use pans with very heavy handles which
cause the pan to tip.
Do not close the lid until the appliance has
cooled down.
Do not use the lid as a work surface or
chopping board. This could damage the
glass and reduce its strength.
Place pans on the centre of the burners.
Position pans so the handles cannot be
accidentally knocked or overhang the
appliance.
Lift pans on and off the pan supports.
Do not slide them across the hob.
x
x
Do not leave accidental spillage on the hob or
removable parts. The spillage should be wiped
up and the parts washed and carefully dried as
soon as the hob, pan supports and burner parts
are cool enough to touch.
A flat based Wok will stand stable on the pan
supports. If you use a round Wok with a collar
support, the collar must be the open wirework
type otherwise the performance of the burner will
be affected.
Take care to avoid burns and scalds
when reaching across the hotplate.
Take extra care when deep fat frying, do
not cover the pan with a lid. Do not leave
a pan unattended. If the pan catches fire,
leave it where it is and turn off all
controls. Place a damp cloth or a fitting
lid over the pan to smother the flames.
Never put water on the fire. Leave to cool
for 30 minutes.
11
THE DUAL GRILL
CAUTION – Accessible parts may be hot
when the grill is in use. Young children
should be kept away.
USING THE DUAL GRILL
The grill is a dual circut grill which means that the full
area of the grill can be used, or for economy
purposes, the centre section only can be used
when cooking smaller quantities of food.
x Turn the second oven/grill control clockwise to the
full power setting (
), then turn down as
necessary.
The grill settings are as follows:-
x
(
)
full grill area at 1/4 power.
x
(
)
centre grill area at full power.
x
(
)
full grill area at full power.
THINGS TO NOTE
x
x
The cooling fan will operate.
Some smoke from fat splashes may be evident as
the grill cleans itself.
x The second oven cannot be operated when the
grill is in use.
x To ensure optimal cooking performance
the elements have been carefully designed, so that
only the inner element glows red. The outer element
is hot, but will remain dark in colour. This gives
you best possible cooking results.
THE GRILL PAN AND HANDLE
The grill pan is supplied with a removable handle.
To attach the handle, press the button on the handle
with the thumb and insert the lip into the widest part of
the bracket. Slide the handle towards the left and
release the button.
Ensure the handle is correctly located.
To remove the handle, press the button on the handle
with the thumb and slide the handle towards the right.
Release the button.
Always remove the grill pan handle during
grilling.
Place the grill pan on the shelf so that the
pan is positioned centrally beneath the grill.
Ensure that the cut out on the underside of
the handle bracket locates between the
bars of the shelf and over the cross bar on
the shelf.
12
HINTS AND TIPS
x
Most foods should be placed on the grid in the grill
pan to allow maximum circulation of air to lift the
food out of the fats and juices.
x
Adjust the grid and grill pan runner position to allow
for different thicknesses of food. Position the food
close to the element for faster cooking and further
away for more gentle cooking.
x
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish
lightly with a little oil or melted butter to keep them
moist during cooking.
x
Accompaniments
such
as
tomatoes
and
mushrooms may be placed underneath the grid
when grilling meats.
GRILLING CHART
x
When toasting bread, use the shelf in position 5
with the grid in the ‘high’ position.
x
Preheat the grill on a full setting for a few minutes
before sealing steaks or toasting. Adjust the heat
setting and the shelf as necessary during cooking.
FOOD
POSITION
Bacon Rashers
x
Beefburgers
Chicken Joints
Chops – Lamb
Pork
The food should be turned over during cooking as
required.
GRILL TIME
(mins in total)
5-6
Adjust
grill
setting
10 - 15
30 - 40
15 - 20
20 - 30
and
Fish – Whole
Trout/Mackerel
grill
Fillets Plaice/Cod
pan
10 - 15
Kebabs
15 - 25
grid
20 - 30
Kidneys –
Lamb/Pig
to
8 - 12
Liver –
Lamb/Pig
suit
10 - 20
different
Sausages
Steaks – Rare
Medium
Well Done
Toasted
Sandwiches
15 - 20
thicknesses
of
6 - 12
12 - 16
14 - 20
food
3-4
The times quoted above are given as a guide and
should be adjusted to suit personal taste.
13
THE SECOND OVEN
The second oven is the smaller of the two ovens. It
is heated by elements in the top and bottom of the
oven. It is designed for cooking smaller quantities of
food. It gives especially good results if used to cook
fruit cakes, sweets and savoury flans or quiche.
The second oven is also ideal for use as warming
compartment to warm dishes and keep food hot.
Use the second oven when you want to warm plates.
Use the lowest setting on the second oven
temperature control.
USING THE SECOND OVEN
x
Turn the second oven temperature control to the
required setting.
THINGS TO NOTE
x
The interior-lighting will illuminate.
x
The indicator neon will glow. It may turn ON and
OFF during use to show that the setting is being
maintained.
x
The cooling fan for the controls may operate after
a time.
x
The grill cannot be operated when the second
oven is in use.
Do not place dishes, tins and trays directly on
the oven base as it becomes very hot and
damage will occur.
TO FIT THE SECOND OVEN SHELF
The shelf should be fitted with the straight rods
uppermost on the frame and the forms towards the
back of the oven. To remove a shelf slide the shelf
towards you until the shelf stop is reached. Tilt shelf
up at the front to that the stops clear the side
supports. Lift shelf clear. To install a shelf, reverse
the above steps. Each shelf position has an upper
and lower support wire, ensure the shelf is placed
between these two support wires.
14
HINTS AND TIPS
x
Arrange the shelves in the required positions
before switching the oven ON. Shelf positions
are counted from the bottom upwards.
x
There should always be at least 2.5cm (1”)
between the top of the food and the element.
This gives best cooking results and allows room
for rise in yeast mixtures, Yorkshire puddings etc.
When cooking cakes, pastry, scones bread etc.,
place the tins or baking trays centrally on the
shelf.
x
Ensure that food is placed centrally on the shelf
and there is sufficient room around the baking
tray/dish to allow for maximum circulation.
x
Stand dishes on a suitably sized baking tray on
the shelf to prevent spillage onto the oven base
and to help reduce cleaning.
x
The material and finish of the baking tray and
dishes used affect base browning. Enamelware,
dark, heavy or non-stick utensils increase base
browning. Shiny aluminium or polished steel trays
reflect the heat away and give less base
browning.
x
Because of the smaller cooking space and lower
temperatures, shorter cooking times are
sometimes required. Be guided by the
recommendations given in the cooking chart.
x
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
x
For economy leave the door open for the shortest
possible time, particularly when placing food into
a pre-heated oven.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
15
SECOND OVEN COOKING CHART
SECOND OVEN
FOOD
Biscuits
Bread
Bread rolls/buns
Cakes:
POSITION
Small & Queen
Sponges
Victoria Sandwich
Madeira
Rich Fruit
Christmas
Gingerbread
Meringues
Flapjack
Shortbread
Casseroles:
Beef/Lamb
Chicken
Convenience Foods
Fish
Fish Pie (Potato Topped)
Fruit Pies, Crumbles
Milk Puddings
Pasta Lasagne etc.
Pastry:
Choux
Eclairs, Profiteroles
Flaky/Puff Pies
Shortcrust
Mince Pies
Meat Pies
Quiche, Tarts, Flans
Roasting Meat, Poultry
Scones
Shepherd’s Pie
Soufflés
Vegetables:
Baked Jacket Potatoes
Roast Potatoes
Yorkshire Puddings: Large
Individual
4
1
1
4
3
3
2
2
1
3
2
3
3
2
2
3
2
2
3
3
3
3
3
3
3
3
2
4
2
3
3
4
4
4
Note: Shelf positions are counted from the bottom of the oven.
16
COOKING
TEMP°C
170 - 190
200 - 220
200 - 220
170 - 180
160 - 170
150 - 160
140 - 150
130 - 140
130 - 140
APPROX
COOK TIME (m)
10 - 20
25 - 30
15 - 20
18 - 25
18 - 20
18 - 25
1¼ - 1½h
2¼ - 2½h
3 - 4½h
depends on size
140 - 150
1¼ - 1½h
90 - 100
2½ - 3h
170 - 180
25 - 30
140 - 150
45 - 65
140 - 160
2½ - 3h
180 - 190
1¼ - 1½h
Follow manufacturer’s instructions
170 - 190
20 - 30
190 - 200
20 - 25
190 - 200
40 - 50
140 - 150
1½ - 2h
170 - 180
40 - 45
180 - 190
30 - 35
170 - 180
20 - 30
210 - 220
25 - 40
190 - 200
15 - 20
190 - 210
25 - 35
180 - 200
25 - 45
160 - 180
see roasting chart
220 - 230
8 - 12
190 - 200
30 - 40
170 - 180
20 - 30
180 - 190
1 - 1½h
180 - 190
1 - 1½h
210 - 220
15 - 25
210 - 220
15 - 25
MAIN OVEN GRILL
CAUTION – Accessible parts may be hot
when the grill is in use. Young children
should be kept away.
USING MAIN OVEN GRILL
x
x
Turn the main oven multifunction selector to grill.
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
x
The cooling fan for the controls may operate after
a time.
x
The interior-lighting will illuminate.
x
Some internal noise may be heard during
operation. This is quite normal.
x
The grill may be used with the door open or with
the door closed.
HINTS AND TIPS
x
Most foods should be placed on the grid in the
grill pan to allow maximum circulation of air to lift
the food out of the fats and juices.
x
Adjust the grid and grill pan runner position to
allow for different thicknesses of food. Position
the food close to the element for faster cooking
and further away for more gentle cooking.
x
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish
lightly with a little oil or melted butter to keep them
moist during cooking.
17
x
Accompaniments such as tomatoes and
mushrooms may be placed around the outer
edges or underneath the grid when grilling
meats.
x
When toasting bread, we suggest that the top
runner position is used with the grid in its 'high'
position.
x
Preheat the grill on full setting for a few minutes
to seal meat or for toasting. Adjust the heat
setting and the shelf position as necessary during
cooking.
x
The food should be turned over during cooking
as required.
GRILLING CHART
FOOD
POSITION
Bacon Rashers
Beefburgers
Chicken Joints
Chops – Lamb
Pork
GRILL TIME
(mins in total)
5-6
Adjust
grill
setting
10 - 15
30 - 40
15 - 20
20 - 30
and
Fish – Whole
Trout/Mackerel
grill
Fillets Plaice/Cod
pan
10 - 15
Kebabs
grid
20 - 30
Kidneys –
Lamb/Pig
to
8 - 12
Liver –
Lamb/Pig
suit
15 - 25
10 - 20
different
Sausages
Steaks – Rare
Medium
Well Done
Toasted
Sandwiches
15 - 20
thicknesses
of
6 - 12
12 - 16
14 - 20
food
3-4
The times quoted above are given as a guide and
should be adjusted to suit personal taste.
18
CONVENTIONAL COOKING
This form of cooking gives you the opportunity to cook
without the fan in operation. It is particularly suitable
for dishes which require extra base browning such as
pies, quiches and flans. Gratin's, lasagne and hotpots
which require extra top browning also cook well in the
conventional oven. For best results cook on one
level.
USING CONVENTIONAL COOKING
x
Turn the main oven multifunction selector to
Conventional Cooking.
x
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
x
The cooling fan for the controls may operate after
a time.
x
The interior-lighting will illuminate.
x
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
x
Some internal noise may be heard during
operation. This is quite normal.
19
HINTS AND TIPS
x
Single level cooking gives best results. If you
require more than one level of cooking use the
main fan oven.
x
The middle shelf allows for the best heat
distribution. To increase base browning simply
lower the shelf position. To increase top browning
raise, the shelf position.
x
There should always be at least 2.5cm (1”)
between the top of the food and the grill element.
This gives best cooking results and allows room
for rise in yeast mixtures, Yorkshire puddings etc.
When cooking cakes, pastry, scones bread etc.,
place the tins or baking trays centrally on the
shelf.
x
Ensure that food is placed centrally on the shelf
and there is sufficient room around the baking
tray or dish to allow for maximum circulation.
x
Stand dishes on a suitably sized baking tray on
the shelf to prevent spillage onto the oven base
and to help reduce cleaning.
x
The material and finish of the baking tray and
dishes used will affect the degree of base
browning. Enamelware, dark, heavy or non-stick
utensils increase base browning. Shiny aluminium
or polished steel trays reflect the heat away and
give less base browning.
x
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
x
For economy leave the door open for the shortest
possible time, particularly when placing food into
a pre-heated oven.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
20
PROFI HOT AIR COOKING
The fan oven is particularly suitable for cooking larger
quantities of food. The advantages of fan oven
cooking are:
PREHEATING
To ensure optimal performance when cooking
convenience foods, pizza or frozen and chilled
ready meals, always preheat the oven first.
The fan oven quickly reaches its temperature, so it is
not usually necessary to preheat the oven. Without
preheating however, you may need to add an extra 5
– 10 minutes on the recommended cooking times. For
recipes needing high temperatures, e.g. bread,
pastries, scones, soufflés etc., best results are
achieved if the oven is preheated first. For best
results when cooking frozen or cooked chilled ready
meals always preheat the oven first.
COOKING TEMPERATURES
Fan oven cooking generally requires lower
temperatures than conventional cooking. Follow the
temperatures recommended in the cooking chart. As
a guide reduce temperatures by about 20°C – 25°C
for your own recipes, using a conventional oven.
BATCH BAKING
The fan oven cooks evenly on both shelf levels,
especially useful when batch baking.
USING PROFI HOT AIR COOKING
x
Turn the main oven multifunction selector to
PROFI Hot air Cooking.
x
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
x
The cooling fan for the controls may operate after
a time.
x
The interior-lighting will illuminate.
x
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
x
Some internal noise may be heard during
operation. This is quite normal.
21
TO FIT THE MAIN OVEN SHELVES
The shelves should be fitted with the straight rods
uppermost on the frame and the forms towards the
back of the oven. To remove a shelf slide the shelf
towards you until the shelf stop is reached. Tilt shelf
up at the front to that the stops clear the side
supports. Lift shelf clear. To install a shelf, reverse
the above steps. Each shelf position has an upper
and lower support wire, ensure the shelf is placed
between these two support wires.
HINTS AND TIPS
x
Arrange the shelves in the required positions
before switching the oven ON. Shelf positions are
counted from the bottom upwards.
x
When cooking more than one dish in the fan
oven, place dishes centrally on different shelves
rather than cluster several dishes on one shelf,
this will allow the heat to circulate freely for the
best cooking results.
x
When batch baking one type of food, e.g. Victoria
sandwich cakes, those of similar size will be
cooked in the same time.
x
It is recommended that when baking larger
quantities the shelf positions should be evenly
spaced to suit the load being cooked. A slight
increase in cooking time may be necessary.
x
Do not place baking trays directly on the oven
base as it interferes with the oven air circulation
and can lead to base burning; use the lower shelf
position.
Do not place cookware and cooking pots
with rough bases e.g. cast iron on the oven
door as damage to the glass may occur.
22
OVEN COOKING CHART
The temperature and baking times are for guidance only, as these will depend on the consistency of the
various ingredients and the number, type and size of baking tray or tins used. It may be necessary to
increase or decrease the temperature to suit individual preference and requirements.
For best results, moist recipes (for example pizza, fruit flans etc) should be baked on one level. To ensure
optimal performance when cooking convenience foods, pizza or frozen and chilled ready meal, always
preheat the oven first.
FAN OVEN
CONVENTIONAL
OVEN
APPROX
COOK TIME (h)
Food
Position
Cooking
Temp °C
Shelf
Position
Cooking
Temp °C
Biscuits
Bread
Casseroles
Cakes:
Small & Queen
Shelf
positions
180 - 190
200 - 220
130 - 160
160 – 170
3
3
3
3
180 - 190
210 - 220
150 - 180
170 - 180
0:10 – 0:25
0:25 – 0:35
1:30 – 2:30
0:18 – 0:30
160 - 170
140 - 150
130 - 140
130 - 140
3
3
3
2
170 - 180
160 - 170
150 - 160
130 - 140
0:20 – 0:35
1:15 – 1:45
2:00 – 2:45
3:00 – 4:45
Depends on size
170 - 190
190 - 200
130 -140
190 - 200
190 - 200
210 - 220
210 - 220
180 - 190
170 - 180
210 - 220
3
3
3
3
3
3
3
3
3
4
170 - 190
190 - 200
130 - 140
160 - 170
190 - 200
210 - 220
210 - 220
190 - 200
190 - 200
220 - 230
0:20 – 0:30
0:40 – 0:60
1:15 – 2:00
0:30 – 0:40
0:15 – 0:25
0:25 – 0:45
0:25 – 0:45
0:25 – 0:50
0:25 – 0:50
0:08 – 0:17
Sponges
Madeira
Rich Fruit
Christmas
are not
critical
but ensure
that oven
shelves are
Fish
Fruit Pies and Crumbles
Milk Puddings
Pastry:
Choux
Shortcrust
Flaky
Puff
Plate Tarts
Quiches/Flans
Scones
evenly
spaced
when more
than one
is used
Note: Shelf positions are counted from the bottom of the oven.
23
ROASTING CHART
INTERNAL TEMPERATURES –
Rare : 50-60°C; Medium : 60-70°C; Well done : 70-80°C
MEAT
TEMPERATURE
COOKING TIME
20-35 minutes per ½kg (1lb)
and 20-35 minutes over
Beef/ Beef boned
160-180°C
Mutton/Lamb
160-180°C
25-35 minutes per ½kg (1lb)
and 25-35 minutes over
Pork/Veal/Ham
160-180°C
30-40 minutes per ½kg (1lb)
and 30-40 minutes over
Chicken
160-180°C
15-20 minutes per ½kg (1lb)
and 20 minutes over
Turkey/Goose
160-180°C
15-20 minutes per ½kg (1lb)
up to 3½kg (7lb) then 10
minutes per ½kg (1lb) over
3½kg (7lb)
Duck
160-180°C
25-35 minutes per ½kg (1lb)
and 25-30 minutes over
Pheasant
160-180°C
35-40 minutes per ½kg (1lb)
and 35-40 minutes over
Rabbit
160-180°C
20 minutes per ½kg (1lb)
and 20 minutes over
The roasting temperatures and times given in the chart should be adequate for most joints, but slight adjustments
may be required to allow for personal requirements and the shape and texture of the meat. However, lower
temperatures and longer cooking times are recommended for less tender cuts or larger joints.
Wrap joints in foil if preferred, for extra browning uncover for the last 20 – 30 min. cooking time.
24
FAN ROASTING
Fan Roasting in the main oven offers an alternative
method of cooking food items normally associated
with conventional grilling.
Fan Roasting helps to minimise cooking smells in the
kitchen and allows you to grill with the oven door
closed. With the exception of toast and rare steaks
you can Fan Roast all the foods you would normally
cook under a conventional grill.
The lower part of the oven can be used to cook
accompaniments at the same time, e.g. tomatoes and
mushrooms with a mixed grill or breakfast.
Dishes prepared in advance such as shepherd's pie,
lasagne and au gratins can be heated through and
browned on the top using the Fan Roasting function.
COOKING TIMES
Cooking is more gentle, therefore food generally takes
a little longer to cook when Fan Roasting compared
with conventional grilling. One of the advantages is
that larger quantities can be cooked at the same time.
USING FAN ROASTING
Always Fan Roast with the oven door closed
and with the grill pan handle removed.
x
Turn the main oven multifunction selector to Fan
Roasting.
x
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
x
The cooling fan for the controls may operate after
a time.
x
The interior-lighting will illuminate.
x
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
x
Some internal noise may be heard during
operation. This is quite normal.
25
HINTS AND TIPS
x
Prepare foods in the same way as for
conventional grilling. Brush lean meats and fish
lightly with a little oil or butter to keep them moist
during cooking.
x
Most food should be placed on the grill pan grid in
the 'high' position in the grill pan to allow
maximum circulation of air around the food.
x
Accompaniments such as tomatoes and
mushrooms may be placed below the grid when
grilling meats, or in a separate dish on a lower
shelf.
x
Foods will cook more quickly the closer they are
to the grill element and the higher the
temperatures selected. Be prepared to adjust
temperatures and shelf positions during cooking if
necessary.
x
Turn food over during cooking as necessary.
x
Ensure that ready prepared or cooked chilled
dishes e.g. shepherds pie, moussaka, lasagne,
etc., are piping hot throughout before serving.
x
FAN ROASTING CHART
FOOD
A temperature range of 140°C - 220° is suitable
for most foods. Be prepared to make suitable
adjustments during cooking to suit individual
requirements. If Fan Roasting on more than one
level, it may be necessary to interchange the food
on the shelves during cooking.
POSITION
TEMP
(°C)
Bacon Rashers
4
200
TIME
(mins
In total)
8-12
Beefburgers
4
190
10-15
Chicken Joints
3
160
35-45
Chops - Lamb/Pork
Fish - Whole
4
170
20-35
Trout/Mackerel
4
170
10-20
Fillets - Plaice/Cod
5
170
10-20
Kebabs
5
170
20-30
Kidneys - Lamb/Pig
4
180
10-15
Liver
4
190
10-15
Sausages
4
190
10-15
Steaks - Medium
5
220
- Lamb/Pig
8-10
each
side
Steaks - Well Done
5
220
10-15
each
side
Heating through
and Browning, e.g.
Au-gratin, Lasagne,
Shepherds Pie.
4
170
20
depends
on
size
NOTE: Shelf positions are counted from the bottom of the
oven.
Times quoted above are given as a guide and should be
adjusted to sit personal taste.
26
PIZZA
This setting can be used for foods such as pizza
where base browning and crispness are required.
USING PIZZA
x
Turn the main oven multifunction selector to
Pizza.
x
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
x
The cooling fan for the controls may operate after
a time.
x
x
The interior-lighting will illuminate.
x
If an automatic programme has been set, the
oven fan and light do not come on until cooking
begins.
Some internal noise may be heard during
operation. This is quite normal.
HINTS AND TIPS
x
Single level cooking using the middle shelf
position gives best results.
x
Ensure that food is placed centrally on the shelf
for maximum air circulation.
x
Be guided by the cook times and temperatures
given on any packaging.
x
Some pizzas should be cooked directly on the
oven shelf. To prevent soiling the oven base,
place a baking tray in one of the lower shelf
positions.
Do not place dishes, tins and trays directly
on the oven base, as it will become very hot
damage will occur.
x
The material and finish of the baking trays and
dishes used will affect base browning.
Enamelware, dark heavy or non-stick utensils
increase base browning. Shiny aluminium or
polished steel trays reflect the heat away and give
less base browning.
27
BOTTOM HEAT
This function uses the lower element to give single
level cooking. This is particularly suitable for dishes
which require extra base browning such as pizzas,
quiches and flans.
USING BOTTOM HEAT
x
Turn the main oven multifunction selector to
Bottom Heat.
x
Turn the main oven temperature control to the
required setting.
THINGS TO NOTE
x
x
The interior-lighting will illuminate.
x
The cooling fan for the controls may operate after
a time.
x
If an automatic cooking programme is set, the
oven fan and oven light do not come on until
cooking begins.
The indicator neon will glow. It may turn ON and
OFF during use to show that the setting is being
maintained.
Do not place dishes, tins and trays directly
onto the oven base as it becomes very hot
and damage will occur.
28
DEFROST
This main oven function defrosts most foods faster
than more conventional methods. It is particularly
suitable for delicate frozen foods which are to be
served cold e.g. cream filled gateaux, cakes covered
with icings or frostings, cheesecakes, biscuits,
scones, etc.
USING DEFROST
x
Turn the main oven multifunction temperature
control to Defrost.
THINGS TO NOTE
x The oven fan and interior-lighting will come on.
x The cooling fan does not operate.
HINTS AND TIPS
x
Place the frozen food in a single layer where
possible and turn it over half way through the
defrosting process.
x
The actual speed of defrosting is influenced by
room temperature. On warm days defrosting will
be faster than on cooler days.
x
It is preferable to thaw fish, meat and poultry
slowly in the fridge. However, this process can be
accelerated by using the defrost function. Small
or thin fish fillets, frozen peeled prawns, cubed or
minced meat, liver, thin chops, steaks etc., can be
thawed in 1 – 2 hours.
x
A 1kg/2¼lb oven ready chicken will be thawed in
approximately 5 hours. Remove the giblets as
soon as possible during the thawing process.
x
Joints of meat up to 2kg/4½lb in weight can be
thawed using the defrost function.
x
All joints of meat and poultry must be thawed
thoroughly before cooking.
x
Always cook
thawing.
x
Do not leave food at room temperature once it is
defrosted. Cook raw food immediately or store
cooked food in the fridge, once it has cooled.
x
Care must always be taken when handling foods
in the home. Always follow the basic rules of food
hygiene to prevent bacterial growth and cross
contamination when defrosting, preparing,
cooking, cooling and freezing foods.
thoroughly
immediately
after
29
CARE AND CLEANING
Before cleaning always allow the appliance to
cool down before switching off at the
electricity supply.
CLEANING MATERIALS
Before using any cleaning materials on your
appliance, check that they are suitable and that their
use is recommended by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives
and scourers should also be avoided.
CLEANING THE
APPLIANCE
OUTSIDE
OF
THE
Do not use abrasive cleaning materials e.g. Hob
Brite, Brillo pads or scourers on painted or printed
finishes as damage may occur. Regularly wipe over
the control panel, doors and appliance sides using a
soft cloth and hot soapy water. To prevent streaking
finish with a soft cloth.
Stainless Steel cream cleaners are abrasive and
should be avoided as they may dull the surface finish.
Any spillage on the stainless steel finish must be
wiped off immediately.
Do not attempt to remove any of the control
knobs from the appliance as this may cause
damage and is a safety hazard.
CLEANING THE CONTROL KNOBS AND
HANDLES
It is strongly recommended that only hot soapy water
is used for cleaning the control knobs and handles.
ANY OTHER CLEANING MATERIALS MAY DULL
THE SURFACE FINISH.
REMOVING
AND
REPLACING
WIREWORK RUNNERS
THE
1. Remove all shelves and furniture from the oven.
2. Hold the wirework at the bottom, unclip from the
cavity side and gently pull towards the centre of
the oven.
3. Unhook the runner at the top and remove from
the cavity.
4. To replace the runners, hook the wirework side
runner into the cavity, slide back and press into
place.
SIDE PANEL
CAVITY
CENTRE
Ensure the wirework runners are firmly in
position before replacing the oven
shelves.
30
CLEANING THE HOB
Clean the hotplate top using a mild abrasive. Take
care not to damage the spark electrodes. If the spark
electrodes are damaged the burners will not light.
You can remove the pan supports, burner caps and
burner crowns to clean them. Again take care not to
damage the spark electrodes.
Clean the burner crowns and pan supports by soaking
them in very hot soapy water. Aluminium based
saucepans can leave shiny metal marks on the pan
supports. You can remove any stubborn stains by
scouring with a soap impregnated steel wool pad. If
you look after the burner crowns and pan supports in
this way they will stay reasonably clean. However the
surface will dull with time.
After cleaning the appliance parts, dry them
thoroughly before you put them back.
WHEN REPLACING HOTPLATE BURNER
PARTS
1. Crown to body. (Do not try to force the crown on
to the body).
Make sure that the hole in the crown is over the
electrode. Check that the location pegs sit in the
slots in the body. When the crown is in this
position let it fall freely on to the body. Check that
the crown can be moved slightly from side to side.
2. Cap to crown. Place cap centrally on the top of
crown (enamel side up). Move sideways and
front to back to check the cap is properly fitted.
3. Check for ignition. If a burner will not light then
you need to check the crown and cap positions.
CLEANING THE SHELVES, WIRE- WORK
RUNNERS AND GRILL/OVEN FURNITURE
All removable parts, except the grill pan handle can
be washed in the dishwasher.
The grill pan, grill pan grid, oven shelves and
wirework runners may be cleaned using a soap
impregnated steel wool pad. Soaking first in hot
soapy water will make cleaning easier.
31
CLEANING INSIDE THE GRILL AND OVEN
COMPARTMENTS
The sides and back of the grill/second oven and main
oven compartments are coated with a special
Stayclean coating. They should not be cleaned
manually.
The vitreous enamel main oven base and grill
compartment base can be cleaned using normal oven
cleaners with care. Ensure that the manufacturers
instructions are followed and that all parts are well
rinsed afterwards.
Aerosol cleaners must not come into
contact with elements, the door seal, or any
painted finishes as this may cause damage.
HINTS AND TIPS
Aerosol cleaners must not be used on
Stayclean surfaces.
Stayclean surfaces destroy splashes of food and fats
when the oven temperature is raised to around 220°C.
It is a good idea to run the oven for an hour or two per
week to ensure continued good performance from the
Stayclean finish.
Slight discolouration and polishing of the Stayclean
surfaces may occur in time. This DOES NOT affect the
Stayclean properties in any way.
Use minimal, if any, extra oil or fat when roasting meat,
potatoes only require brushing with fat before cooking.
Extra fat in the oven during roasting will increase
splashing and soilage.
It is NOT necessary to add water to a meat tin when
roasting. The water and the fat juices from the joint
create excessive splattering during cooking – even at
normal temperatures, as well as causing condensation.
Covering joints during cooking will also prevent
splashing onto the interior surfaces. Removing the
covering for the last 20-30 minutes will allow extra
browning if required. Some large joints and turkeys
especially benefit by this method of cooking, allowing
the joint to cook through before the outside is overbrowned.
32
CLEANING THE DOOR(S)
To prevent damaging or weakening the
door glass panels avoid the use of the
following:
x
Household detergents and bleaches
x
Impregnated pads unsuitable for nonstick saucepans
x
Brillo/Ajax pads or steel wool pads
x
Chemical oven pads or aerosols
x
Rust removers
x
Bath/Sink stain removers
Warning! Number of glasses depends
on model. Your appliance might have
only two glasses.
CLEANING BETWEEN THE OUTER AND
INNER DOOR GLASS
The inner door glass is removable for cleaning.
TO REMOVE THE INNER GLASS
Open the oven door to gain access to the top of the
oven door.
To remove the top trim:Second Oven - Carefully pull the trim away from the
door and lift off.
Main Oven - Carefully push the trim towards the oven.
Remove the seal.
Hold the door glass securely in place with one hand
before sliding the glass out with the other hand.
Clean the outer and inner glass using hot soapy water
or Hob Brite cleaner may be used. Do not use Hob
Brite on the Stainless Steel or painted finishes.
Ensure that all parts are well rinsed and thoroughly
dried before attempting to replace the outer door.
If the door glass panel becomes chipped or has
deep scratches the glass will be weakened and
must be replaced to prevent the possibility of
the panel shattering. Please contact your local
Service Force Centre who will be pleased to
advise further.
TO REPLACE THE INNER GLASS
To ensure the glass is properly located the text 'This
side up' should be facing towards you at the top edge
of the door and facing into the cavity.
Holding the glass with both hands, gently slide the
glass into the side trims of the oven door. Always
ensure that the glass is returned to the same side trim
it was removed from.
Replace the seal on the main oven door if removed.
To replace the trim, line up the clips on the underside
of the trim with the connectors at the top of the door.
Carefully slide the trim towards the door.
Ensure the trim is securely in place before closing the
oven door.
Please note that the door
glass on your product may
differ in type and shape
from that shown in the
diagram.
Do not attempt to use the oven without the
glass being in place.
33
REPLACING
BULB
AN
INTERIOR-LIGHTING
The type of bulb required is a 300°C 40 watt small
Edison Screw.
Disconnect
the
appliance
from
the
electricity supply before replacing the bulb.
1. Make sure the appliance is cool before replacing
the bulb.
2. Open the door and remove the shelves and
wirework runners.
3. Remove the glass cover by turning it to the left.
4. Unscrew the bulb by turning it to the left.
5. Fit a new bulb and then replace the glass bulb
cover.
6. Refit the wirework runners and replace the oven
shelves.
7. Restore the electricity supply and reset the time of
day.
34
SOMETHING NOT WORKING?
Please carry out the following checks on your appliance before calling a Service Engineer. It may be that the
problem is a simple one which you can solve yourself without the expense of a service call.
In-guarantee customers should make sure that the checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
PROBLEM
POSSIBLE SOLUTION
The grill, ovens and timer do not work.
Check that the appliance has been wired in to the appliance supply
and is switched on at the wall.
Check that there is not a problem with your gas supply.
You can do this by making sure the other gas appliances such as
central heating or gas fires are working.
Check that the main appliance fuse is working.
If you have checked the above:
Allow the appliance to cool for a couple of hours. The appliance
should now be working normally.
The grill and second oven work but the
main oven does not.
Check that the time of day has been set on the clock. Check that the
oven is set for manual cooking.
The timer does not work.
Check that the instructions for the operation of the timer are being
closely followed.
The indicator neons are not working
correctly.
Check that you have selected only the function you require. Ensure
all other controls are in the Off position.
The oven is not cooking evenly.
Check that the appliance is correctly installed and is level.
Check that the recommended temperatures and shelf positions are
being used.
The interior-lighting fails to illuminate.
The interior-lighting bulb may need replacing.
If the Main Oven is set for automatic cooking the interior-lighting will
illuminate when the cook time begins.
The oven temperature is too high or too
low.
Check that the recommended temperatures and shelf positions are
being used. Be prepared to adjust the temperature up or down
slightly to achieve the results you want.
Refer to section 'Using The Main Oven'.
The cooling fan does not work.
Check that there is not a problem with your electricity supply.
The hob burners will not light.
Ensure the burner parts have been placed correctly.
Check that there is not a problem with your gas supply.
You can do this by making sure the other gas appliances such as
central heating or gas fires are working.
The flame colour is orange/yellow.
Due to the design of the burner the flame can appear to be orange
/yellow (flame disturbance) in certain areas of the burner this is a
natural occurrence.
The burner is not igniting or only
partially lighting.
Check that the burner is dry and that food spillage or cleaning fluids
are not present on the burner. This can be dried with a cloth and
stubborn marks cleaned away with a dry nylon brush (old toothbrush
etc).
The burner sounds noisy.
It is natural for the burners to emit noise as the gas is being drawn
through the burner and may reduce as they heat up.
The burner is emitting a popping sound.
This is a natural occurrence when the burner is alight and does not
affect the performance of the burner.
Noise.
It is normal for some metal parts on the cooker to produce noise
when in use, this is due to expansion and contraction when heating
up and cooling down.
35
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk.
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working?".
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating plate).
5. The purchase date.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service
calls.
CUSTOMER CARE DEPARTMENT
For general enquires concerning your AEG-Electrolux appliance or for further information on AEG-Electrolux
products, please contact our Customer Care Department by letter or telephone at the address below or visit our
website at www.aeg-electrolux.co.uk
Customer Care Department
AEG-Electrolux
Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 0870 5 350350 (*)
*calls to this number may be recorded for training purposes.
36
GUARANTEE CONDITIONS
Standard guarantee conditions
We, AEG-ELECTROLUX, undertake that if within 12 months of the date of purchase this AEG-ELECTROLUX
appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will at
our discretion repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition
that:
x
x
x
x
x
x
x
The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating
plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
operating and maintenance instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Service Force Centre.
Any appliance or defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30 am and 5.30 pm Mon-Fri excluding bank holidays. Visits may be
available outside these hours in which case a charge will be made.
Exclusions
This guarantee does not cover:
x
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
x
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
United Kingdom.
x
Appliances found to be in use within a commercial environment, plus those which are the subject of rental
agreements.
x
Products of AEG-ELECTROLUX manufacture which are not marketed by AEG-ELECTROLUX.
37
TECHNICAL DETAILS
DIMENSIONS
Height:
Width:
Depth:
Weight:
900 mm (nominal)
600 mm (nominal)
600 mm (to front of door panel)
60Kg Net
Space for fixing at hotplate level 2mm minimum clearance.
Space for fixing above hotplate level See important note 'Location of Appliance'.
Minimum space above hotplate 650mm (If cooker hood is fitted refer to the cooker hood installations.
Minimum distance from rear wall 5mm (spacer given by pressed spacer on vent panel).
CONNECTIONS
Gas connection:-
Rear left hand side of appliance at hotplate level Rc ½ (½" B.S.P. female)
Electrical connection:-
230 - 240 V 50 Hz Mains connected at rear centre of appliance using at least
6mm2multi core PVC insulated cable.
LOADING INFO: Electric ovens
Voltage:
230-240 Volts AC 50Hz
Wattage:
4.4 - 4.8kW
LOADING INFO: Gas hotplate
Natural Gas
Injector marking
R.H.F
1.0kW
(3412 Btu/h)
070
GENERAL
Ignition
Spark Gap
(H.T. Spark)
3-4mm
Heat Input
GAS CATERGORY
CAT. I2H
R.H.R
1.9kW
(6483 Btu/h)
096
L.H.R.
1.9kW
(6483 Btu/h)
096
L.H.F.
3.4kW
(11600 Btu/h)
136
COUNTRIES OF DESTINATION
GB
This appliance complies with: European Council Directives Low voltage
Directive73/23/EEC, Gas Directive 90/396EEC EMC Directive 89/336/EEC, CE Marking
Directive 93/68EEC. Energy Label Directive 2002/40/EC.
38
INSTALLATION INSTRUCTIONS
IMPORTANT - SAFETY REQUIREMENTS
This appliance is not suitable for
installation in flats or other mutli
occupancy dwellings as defined
in clause 8.2.1 of IGE/G/5.
Check that this model is suitable for the type of supply
available. This appliance must be installed and/or
serviced by a competent person, in accordance with
the Gas Safety (Installation and Use) Regulations
Current Editions and the IEE Wiring Regulations.
Detailed recommendations are contained in the
following British Standards Codes of Practice BS.5440: Par 2 and BS.6891. All British Standards
must be 'Current Editions'.
This appliance must be installed by a
qualified electrician / competent person
(Gas Safe Regoster registered)
Safety may be
impaired if installation is not carried out in
accordance with these instructions.
Before connecting the appliance make
sure that the voltage of your electricity
supply is the same as that indicated on the
rating plate. This is situated on the lower
front frame of the appliance and can be
seen upon opening the door. Alternatively
the rating plate may also be found on the
back or top of some models (where
applicable).
Do not alter the electrical circuitry of this
appliance.
PROVISION FOR VENTILATION
This appliance is not connected to a combustion
products evacuation device. It shall be installed and
connected in accordance with the current installation
regulations. Particular attention shall be given to the
relevant requirements regarding ventilation.
The room containing the appliance should have an air
supply in accordance with BS.5440: Part 2 Current
Edition. All rooms require an openable window or
equivalent and some rooms will require a permanent
vent as well. For room volumes up to 5m3 an air vent
of 100cm2 is required: for room volumes between 5m3
and 10m3 an air vent of 50cm2 is required. If the room
has a door that opens directly to the outside, no air
vent is required. For room volumes that exceed 11m3
no air vent is required. If there are other fuel burning
appliances in the same room, BS.5440: Part 2 Current
Edition should be consulted to determine the requisite
air vent requirements.
Prolonged intensive use of the appliance may call for
additional ventilation, for example opening a window,
or more effective ventilation, for example increasing
the level of mechanical ventilation where present.
39
MOVING YOUR APPLIANCE
You may damage some soft or badly fitted floor
coverings when you move the appliance. The floor
covering under the appliance should be securely fixed
so it does not ruck up when you move the appliance
across it. Alternatively you could remove the floor
covering. This appliance is heavy and care must be
taken when moving it. Do not try to move the
appliance by pulling the door handles.
To move the appliance open the grill door. Raise the
appliance off its front feet by lifting it from inside the
oven. Pull the appliance forward. When you replace
the appliance push it back to the stop and make sure
there is the same gap at each rear corner.
FOR YOUR SAFETY
Do not try to disconnect the appliance from the gas
supply if the supply pipe does not have a bayonet
connection, as described in the installation
instructions. If this is the case contact the person who
installed the appliance.
LOCATION OF APPLIANCE
This appliance must not be installed in a bed-sitting
room of volume less than 20m3 or in a bathroom,
shower room or garage. It is essential that the
appliance is positioned as Fig 1. a. Shelves, wall
cabinets and cooker hoods must be fitted a minimum
of 650mm directly above the top of the hotplate (or
greater for cooker hoods if recommended by
manufacturers instructions) and 400mm above the
hotplate when fitted in line with the outside of the
appliance. If the units are intended to be fitted
adjacent to the appliance but less than 400mm above
the hotplate, then a minimum space of 50mm must be
maintained between the sides of the unit and the
appliance as Fig 1.b. Curtains must not be fitted
immediately behind the appliance or within 150mm of
the sides of the hotplate. If fitted next to or between
two base units a minimum space of 2mm must be left
between each unit and the sides of the appliance.
The levelling feet fitted to the appliance will achieve a
nominal height to hotplate of 907mm + / - 5mm.
Fig 1.a
LEVELLING THE APPLIANCE
Adjustment to suit floor conditions or height is
obtained by rotating clockwise or anti clockwise the
feet at the front and rear of the appliance. A spirit
level should be placed on one of the shelves to
confirm the appliance is correctly levelled.
40
Fig 1.b
CONNECTING TO THE ELECTRICITY SUPPLY
Warning: This appliance must be earthed.
Do not earth this appliance to the gas
supply piping.
Connect to 230 - 240V AC supply only.
x
The electrical connection should be made using a
double pole isolating switch (cooker socket) with
at least 3mm contact separation in all poles. The
cable must have conductors of sufficiently high
cross-sectional area to prevent overheating and
deterioration.
x
We recommend you use a new length of 6mm2
twin core and earthed cable to ensure your safety.
x
Make connection as shown in Fig 2 by proceeding
as follows:-
x
Preform wires to the appropriate shape to suit
fitting into the mains terminal block.
x
Strip inner
strippers.
x
x
Twist the bared wires using pliers.
insulation
on wires
using wire
Cut bared wires 10mm away from the end of the
inner insulation. Where uninsulated Earth wires
are used ensure they are suitably sheathed to
leave 10mm bare wire to fit into the terminal.
x
Clamp bare wires into the relevant terminal (Fig.
2.) and check they are held by tugging each one
in turn.
x
x
Ensure all screws are securely tightened.
x
Connect the remaining end of the mains cable to
the appliance to the appliance point / junction box.
x
Place fuse / miniature circuit breaker in circuit and
switch on at mains.
Fig.2.
ENSURE THAT THE LINKS ARE FITTED
AS SHOWN IN FIG.2.
Clamp the mains cable securely ensuring 5mm of
the outer insuation is inside the terminal block and
that the wires are not taut but not so slack as to
cause any fouling.
When refitting the mains terminal cover, ensure that
the lower tabs are located inside the bottom edge of
the aperture, before fixing the two screws into the top
edge of the mains terminal cover. See Fig.3. Ensure
that the cover is securely fastened.
NOTE: HOUSE CIRCUIT
Earth leakage / continuity tests must be carried out
before the appliance is connected to the mains supply
and re-checked after fitting.
Fig.3.
41
CONNECTING TO GAS SUPPLY
This appliance is designed to be installed with an
appliance flexible connection only. Supply piping
should not be less than R3/8. Connection is made to
the Rc ½ (½” B.S.P.) female threaded entry pipe
located just below the hotplate level on the rear left
hand side of the appliance. NOTE: ONLY LIQUID
SEALANTS TO BE USED WHEN INLET GAS PIPE
IS FITTED I.E.: DO NOT USE P.T.F.E. SEALANT
TAPE. Carry out a gas tightness test after connecting
to the gas supply. The gas bayonet connector must
be fitted in the shaded area indicated in Fig.4. Take
into account that it must be possible to pull the
appliance forward sufficiently. Ensure the hose does
not become trapped when pushing the appliance into
position.
Fig.4.
IMPORTANT: FLEXIBLE TUBING USED MUST
COMPLY WITH BS.669 CURRENT EDITION.
FITTING THE STABILITY CHAIN
It is recommended that if the appliance is to be
installed with a flexible supply pipe, a stability chain
be fitted and is available from your supplier (see
Important Safety Requirements). These instructions
should be read in conjunction with any leaflet packed
with the stability chain.
1. Place the appliance in its intended position and
level appliance.
2. Mark a position 100mm from the top of the rear
right hand corner.
3. Measure down 150mm from this point. This gives
the position of the wall anchor point for the
stability chain.
4. The stability chain anchor point on the appliance
is shown in the diagram Fig. 5.
Fig.5.
PRESSURE TESTING
1. The Triple crown injector is used as a pressure
test point.
2. Connect the pressure gauge to the Triple crown
injector.
3. Check the supply pressure by turning the Triple
crown burner on and one other hotplate burner
full on and light the appropriate burner. The
pressure should be 20mbar
4. Turn off the taps, disconnect the pressure gauge.
5. Check operation of each hotplate burner.
42
CHECKING THE GRILL
Place the grill pan containing the grid into the grill
compartment. Open the grill door and turn the grill
control to full on. Visually check that the elements
are heating up.
CHECKING THE HOTPLATE
Lift the lid. Fit the burner crowns and caps ensuring
that they are correctly seated.
Fit the pan supports. Check each of the hotplate
burners in turn by turning the hotplate tap to its full on
position and pushing the ignition button.
As soon as the burners are lit the button can be released.
CHECKING LID SHUT-OFF DEVICE
1. Lift the lid
2. Turn one hotplate tap to its full on position and
push the ignition button.
3. Close lid. There should now be no gas supply to
the hotplate and the burner will go out.
4. Turn off the hotplate and lift the lid. The gas
supply should now be restored to the hotplate,
when the tap is turned on.
CHECKING THE TOP OVEN
1. Ensure the oven door is closed.
2. Turn on the top oven thermostat to the highest
setting.
3. Ensure that the oven is heating up by checking
firstly that the oven neon illuminates.
4. After a short period the heat from the oven
element may be felt with the oven door open.
CHECKING THE MAIN OVEN
1. Turn on the main oven thermostat to the highest
setting.
2. Ensure the oven is heating up by checking firstly
that the oven neon illuminates.
3. After a short period the heat from the oven
element may be felt with the oven door open.
4. Check that the oven light and the oven fan are
functioning.
TO SET THE TIME OF DAY
Please refer to the Timer section.
GENERAL NOTE
Instruct the user on how to use the appliance and its
ignition system. Refer the user to the wording on the
inside cover which gives advice on the safe
operation of the appliance.
43
www.electrolux.com
www.aeglectrolux.o.uk
349172500-G-082009