Electrolux EDB 876 Oven User Manual

Model EDB 876
Ensure that all vents are left unobstructed to ensure
IMPORTANT SAFETY INFORMATION
ventilation of the oven cavity.
These warnings are provided in the interests of your safety. Ensure that you understand them all before installing
or using the appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of
these warnings contact the Customer Care Department. The address is on the back page of this book.
INSTALLATION
Never line any part of the appliance with foil.
Stand clear when opening the drop down oven
doors. Support the doors using the handles until fully
open.
Never leave the appliance unattended when the
oven door is open.
Do not place sealed cans or aerosols inside the
oven. They may explode if they are heated.
Ensure that all control knobs are in the OFF position
when not in use.
Do not stand on the appliance or on the open oven
doors.
Do not hang towels, dishcloths or clothes from the
appliance or its handles. They are a safety hazard.
The appliance must be installed according to the
instructions supplied. The installation work must be
undertaken by a competent person as stated in the
Gas Safety (Installation & Use) regulations current
edition.
The installer should check that the appliance is
suitable for the gas supply by checking the rating
plate.
The appliance must be installed in an adequately
ventilated room.
NOTE: It is imperative that the appliance is left in the
base to protect both the appliance and the floor.
This appliance is heavy and care must be taken
when moving it. Do not try to move the appliance
by pulling the door handles.
Warning: Do Not attempt to lift this appliance by the
handles.
All packaging, both inside and outside the appliance
must be removed before the appliance is used.
It is dangerous to alter the specifications or modify
the appliance in any way.
After installation please dispose of the packaging with
due regard for safety and the environment. Your local
authority can arrange this.
CLEANING AND MAINTENANCE
The appliance is heavy and care must be taken
when moving it.
For Hygiene and safety reasons this appliance
should be kept clean at all times. A build-up of
fats or other foodstuffs could result in a fire
especially in the grill pan.
This appliance should be kept clean at all times. A
build-up of fats or other foodstuffs could result in a
fire, especially in the grill pan.
Do not leave cookware containing foodstuffs, e.g.
fat or oil in the appliance in case it is inadvertently
switched on.
Always allow the cooling fan to cool the appliance
down before switching off at the wall prior to carrying
out any cleaning / maintenance work.
Only clean this appliance in accordance with the
instructions given in this book.
CHILD SAFETY
Do not allow young children to play with any part of
the packaging.
This appliance is designed to be operated by adults.
Young children must not be allowed to tamper with
the controls or play near or with the appliance.
CAUTION: Accessible parts may be hot when
the grill is in use. Young children should be
kept away.
SERVICE
DURING USE
Repairs should not be carried out by inexperienced
persons as this may cause injury or serious
malfunction. This appliance should be serviced by
an authorised Service Engineer and only genuine
approved spare parts should be used. Details of
servicing and repair arrangements are supplied on
page 35 of this book.
This appliance has been designed for domestic use
to cook edible foodstuffs only, and must not be used
for any other purpose.
Take great care when heating fats and oils as they
will ignite if they become too hot.
Never place plastic or any other material which may
melt in or on the oven.
Do not stand too close to the oven or grill while in
use as warm air will exhaust from the grill cavity and
the vents on the front frame of the appliance.
When lighting any burner check that it is lit before
leaving the appliance.
When turning off any burner do not leave the
appliance until the flame has gone out.
Do not leave the grill pan handle in position when
grilling and ensure oven gloves are used to remove
and replace the handle, as it will become hot.
Always use oven gloves to remove and place food
in the oven.
AT THE END OF THE COOKERS LIFE
When the time comes to dispose of your appliance
please contact your local Council Authority. They
can arrange to dispose of the appliance in a safe
and controlled manner.
The number will be in the telephone book.
Please read this
instruction book carefully
before use and retain
for future reference.
2
CONTENTS
FOR THE USER
Important Safety Information
Description of the appliance
Getting to Know Your Oven
The Cooling Fan for the Controls
Location
2
4
5
6
6
Before Using The Appliance
Rating Plate
Connecting to the Electricity Supply
When First Switching On
Condensation and Steam
Cookware
Grill and Oven Furniture
7
7
7
7
8
8
9
The Electronic Timer
10
The Grill
Uses of the Grill
How To Light the Grill
Things To Note
The Grill Shelf
The Grill Pan and Handle
Hints and Tips
Grilling Chart
13
13
13
13
14
14
15
16
The Top Oven
Uses of the Top Oven
Preheating
How To Light the Top Oven
Things To Note
To Fit the Top Oven Shelf
Hints and Tips
Top Oven Cooking Chart
17
17
17
17
17
18
18
19
The Main Oven
Uses of the Main Oven
Preheating
How To Light the Main Oven
Things to Note
To Fit the Main Oven Shelves
Hints and Tips
Main Oven Cooking Chart
20
20
20
20
20
21
21
23
Slowcook Feature
Uses of Slowcook
How To Use Slowcook
Things to Note
Hints and Tips
24
24
24
24
24
Care and Cleaning
Cleaning Materials
Cleaning the Outside of the Appliance
Cleaning the Outer and Inner Door
Glass Panels
Cleaning Inside the Ovens
To Remove the Wirework Runners
Cleaning the Shelves, Wirework Runners
and Oven Furniture
Care of Stayclean Surfaces
The Oven Cleaning Cycle
Things to Note
Hints and Tips
Replacing an Oven Light Bulb
27
27
27
Something Not Working
Service and Spare Parts
Guarantee Conditions
33
35
36
28
29
30
30
30
31
31
31
32
FOR THE INSTALLER
Technical Details
Things You Need to Know
Warnings
Things to Note
37
38
38
38
Getting Things Ready
Preparing Cabinet for Fitting Oven
Flexible Pipe Installation
39
39
39
Making the Electrical Connections
Connection to Electricity Supply
Checking Electrical Connections
Pressure Testing
41
41
42
43
Please read the whole instruction book before
using the appliance. To help you the following
symbols will be found in the text.
Safety Instructions
Step by Step Instructions
Hints and Tips
3
DESCRIPTION OF THE APPLIANCE
Built in gas double oven
WARNING: THIS APPLIANCE MUST BE EARTHED AND PROTECTED BY A 3 AMP FUSE
Top Oven / Grill
Electronic
Timer
Control
Knob
Control
Panel
Main Oven
Your built in appliance comprises of a gas oven and grill in the top compartment. The top oven is
convenient and economical for mid-week use because of its size.
The main oven is the larger of the two ovens. It is particularly suitable for cooking larger quantities of
food. In addition, the Slowcook feature allows you to cook a range of foods over a long period of time
at a low temperature.
The Main oven can be automatically controlled by the electronic timer.
4
GETTING TO KNOW YOUR OVEN
The Control Panel
Electronic Timer
Grill / Top Oven Control
Main Oven Control
5
THE COOLING FAN FOR THE CONTROLS
Your appliance has a cooling fan fitted behind
the controls to prevent them from overheating.
The cooling fan will come on immediately when
the top oven or grill is switched on and after a
short time when the main oven is in use.
The cooling fan may run on after the ovens or
grill are turned off for a period of time to cool
the appliance down. It may continue to switch
on and off until the appliance is cool.
Always allow the cooling fan to cool
the
appliance
down
before
switching off at the wall prior to
carrying out any cleaning or
maintenance work.
NOTE
The action of the cooling fan will depend on
how long the ovens or grill have been used and
at what temperature. It may not run on where
the grill or oven has only been used for a short
time.
Do not stand too close to the grill or
oven when in use as warm air will
exhaust from the grill cavity and
oven vents.
LOCATION
All gas ovens require adequate
ventilation. The room the oven is fitted
in must have a good air supply that
meets the standard BS 5440 Part 2
(current edition). Your installer will tell
you if you are not sure.
The oven may be placed in a
kitchen, kitchen/diner or bedsit but not
in a bathroom or shower room. It
should not be installed in a bedsit
smaller than 20m3.
L.P.G. cookers MUST NOT be installed
below ground level, i.e. in a basement,
or aboard any boat, yacht or other
vessel.
The use of a gas cooking appliance results in
the production of heat and moisture in the room
in which it is installed. Ensure that the kitchen is
well ventilated: keep natural ventilation holes
open or install a mechanical ventilation device
(mechanical extractor hood).
Prolonged intensive use of the appliance may
call for additional ventilation, for example
opening of a window, or more effective
ventilation, for example increasing the level of
mechanical ventilation where present.
6
BEFORE USING THE APPLIANCE
RATING PLATE
This is situated on the lower front frame of the
appliance and can be seen upon opening the
top cavity door. Alternatively the rating plate
may also be found on the back or top of some
models (where applicable).
The appliance must be protected by a suitably
rated fuse or circuit breaker. The rating of the
appliance is given on the rating plate.
Do not remove the rating plate from the
appliance as this may invalidate the
guarantee.
This appliance must be earthed
and protected by a 3 amp fuse.
CONNECTING TO THE
ELECTRICITY SUPPLY
The plug supplied with the oven can be fitted
directly to a suitable three pin earthed socket.
If you have to change the fuse replace it with a
3 amp fuse which has been ASTA approved to
BS 1362.
Do not use the plug until you have put the fuse
cover back on. If you cut the plug off dispose of
it safely as it will be a shock hazard if it is
inserted into a 13 amp socket elsewhere in the
house.
If the ignition system doesn't work there may be
a fault with the electrical supply. First, check the
socket by trying out another piece of electrical
equipment in it, if that works correctly renew the
fuse in the plug.
If the fuse keeps failing there is a fault in the
oven which must be put right. Do not use a
fuse with a rating higher than 3 amps. Do not
carry out other electrical work. Unplug the oven
and tell your installer.
WHEN FIRST SWITCHING ON
The timer must be set to manual operation
before the main oven can be operated. This
must be done whenever the appliance is
switched off at the wall or when there has been
a power failure. For instructions on how to set
the timer see page 10.
The Top Oven and the Grill are not controlled
by the electronic timer.
7
PREPARING TO USE YOUR
APPLIANCE
Wipe the base of the ovens with a soft cloth
and some hot soapy water and wash the grill
and oven furniture before use. The grill and
ovens should be heated without food to burn off
any residue from the grill and oven surfaces. To
do this run the oven at Gas Mark 7 for
approximately 10 - 15 minutes. The procedure
should be repeated with the grill for
approximately 5 - 10 minutes.
During this period an unpleasant odour may be
emitted, it is therefore advisable to open a
window for ventilation.
CONDENSATION AND STEAM
When food is heated it produces steam in the
same way as a boiling kettle does. The ovens
are vented to allow some of this steam to
escape. However, always stand back from the
appliance when opening the oven doors to
allow any build up of steam or heat to release.
If the steam comes into contact with a cool
surface on the outside of the appliance, e.g. a
trim, it will condense and produce water
droplets. This is quite normal and is not caused
by a fault on the appliance.
To prevent discolouration occurring, regularly
wipe away condensation and any soilage from
the appliance surfaces.
COOKWARE
Baking trays, dishes etc., should not be placed
over the oven burner. This will damage the
oven as well as the ovenware.
Do not use baking trays larger than 30cm x
30cm (12" x 12") as they will restrict the
circulation of heat and may affect performance.
Advice on the effect of different materials and
finishes of bakeware is given in 'Hints and Tips'
in the appropriate oven section.
If using a baking tray larger than 30cm x 25cm
(12" x 9") in the top oven you may need to turn
it round during cooking.
8
GRILL AND OVEN FURNITURE
The following items of oven furniture have been
supplied with the appliance.
1 grill pan
1 grill pan handle
1 grill pan grid
1 meat tin
2 shelves for main
oven cooking
1 shelf for grilling and
top oven cooking
Scuffing of the Stayclean panel/s by
the oven furniture pack may occur
during transit.
These marks will disappear after the
oven has been used for the first
time.
9
THE ELECTRONIC TIMER
The electronic timer can indicate the time of
day, operate as a minute minder and
automatically time the main oven.
Auto
Symbol
A - Auto Symbol ( automatic cooking)
- Bell Symbol ( minute minder)
- Cookpot Symbol ( manual cooking)
Bell
Symbol
Please note that this is a 24 hour clock, for
example 2pm is shown as 14.00.
If the oven is switched off on the wall or there is
loss of power the clock will stop and you will not
be able to use the appliance. When you first
switch the electricity supply on, the timer display
will flash.
TO SET THE TIME OF DAY
1. Press buttons
and
Release the buttons.
together.
2. Within 5 seconds press the
button until
the time of day shows in the display.
The cookpot symbol (
) will be showing.
THE MINUTE MINDER
1. Press and release the
Cookpot Symbol
button.
2. Within 5 seconds press the
button until
the display shows the time you want.
Our diagram shows the timer set to 5 minutes.
After a few seconds the time of day will show in
the display.
When you are using the minute minder you can
check the number of minutes remaining by
pressing the
button.
At the end of the timed period an alarm will
sound. Switch off the alarm by pressing the
button.
After a few seconds the time of day shows in
the display.
10
AUTOMATIC TIMER CONTROL
The automatic timer can be used with the main
oven only.
TO SWITCH THE MAIN OVEN
ON AND OFF AUTOMATICALLY
1. Ensure the clock is showing the correct time
of day.
2. Place food in the main oven.
3. Set the length of time you want the food to
cook for by pressing and releasing the
button and then pressing the
button until
the correct cooking time is displayed.
This must be completed within 5 seconds of
pressing the
button.
The maximum cooking time is 23 hours 59
minutes.
The Cookpot and Auto symbols will show in the
display. Our diagram shows the cooking time
set for 2 hours 30 minutes.
After a few seconds the time of day shows in
the display.
4. To set the time you want the food to be
cooked by, press and release the
button.
This will show you the earliest possible stop
time.
If this is different to the time you want the food
to be cooked by, press the
button within 5
seconds until the correct stop time shows in the
display. Our diagram shows the food is to be
cooked by 18.00 (6pm).
After a few seconds the time of day shows in
the display and the Cookpot symbol goes out.
The 'Stop' time must not be more than 23 hours
59 minutes from the time of day. For example, if
the time of day is 09.00 hours (9.00am) the
latest 'Stop' time will be 08.59 (8.59am) the next
day.
5. Turn the oven control to mark 9 then to the
required setting.
The clock will work out what time the oven will
switch itself on and will switch the oven off at
the end. An audible signal will sound when
cooking is complete. To cancel the alarm, see
below.
11
RETURNING THE APPLIANCE
TO MANUAL OR TO CANCEL AN
AUTOMATIC PROGRAMME
Once automatic cooking is complete an alarm
will sound and the Auto symbol will flash to
remind you that the oven needs to be set for
manual operation.
1. To do this press buttons
and
together.
After a few seconds the timer will show the
time of day. The cookpot will show in the
display and the oven will switch on again.
2. Turn off the oven control.
TO SET THE TIMER TO
SWITCH OFF ONLY
This is useful if you want to begin cooking
immediately but have the Main oven switch off
whilst you are out.
1. Ensure the clock is showing the correct time
of day.
2. Place food in the oven.
3. Set the length of time you want the food to
cook for. Press and release the
button
and then press the
button within 5
seconds until the correct cook time is
showing.
Our diagram shows the timer set for 2 hours 30
minutes.
After a few seconds the time of day shows in
the display.
4. Turn the control to mark 9 then to the
required setting.
If you want to check the time the oven will
switch off simply press the
button and the
'Stop' time will be displayed.
At the end of the cooktime the oven will switch
off, the alarm will sound and the auto symbol
will flash.
5. To cancel and return to manual operation
press buttons
and
together.
6. Turn off the oven temperature control.
12
THE GRILL
WARNING
Accessible
parts
become hot when the grill is in use.
Keep children away.
USES OF THE GRILL
The grill is situated in the Top oven
compartment.
The grill gives variable heat settings. Use the
high setting for foods that cook quickly such as
toast and the lower setting to cook thicker foods
such as chicken after it has been browned on
the high setting.
GRILL / TOP OVEN
HOW TO LIGHT THE GRILL
1. Open the Grill / Top Oven door.
2. Push in the grill / top oven control and turn it
clockwise to the highest setting. This is
shown by a large flame symbol.
3. Adjust the setting as required.
4. Place grill pan with food under the grill.
The grill door must be left open
when grilling.
Check that the grill burner is lit
before you leave the appliance.
Never cover the grill pan or grid
with foil as this can lead to grill
fires.
GRILL / TOP OVEN
TO TURN OFF THE GRILL
BURNER
1. Push in the control knob and turn it to the Off
position. This is shown by a large dot.
THINGS TO NOTE
The cooling fan for the controls will operate
as soon as the grill control is turned. For
more information on the operation of the
cooling fan turn to page 6.
The oven light will illuminate.
If the oven door is closed whilst the grill
burner is lit, it will go out. The burner will
automatically re-light when the door is
opened.
Always light the burner before placing food
under the grill.
13
THE GRILL SHELF
1
The grill shelf can be used in one of three
positions. Shelf positions are counted from the
top downwards.
2
3
The shelf should be fitted with the straight rods
uppermost on the frame and the forms towards
the back of the oven. If not fitted correctly the
anti-tilt and safety stop mechanism will be
affected.
Back of the oven
When using the grill pan in positions 2 and 3
the shelf must be withdrawn before the pan can
be located or removed.
Straight Rods
Frame
Ensure the pan is properly located.
THE GRILL PAN AND HANDLE
The grill pan has a removable handle.
To insert the handle, press the button on the
handle with the thumb and pivot the handle
slightly upwards inserting the lip into widest part
of the bracket. Move the handle towards the
left, lower into position and release the button.
Ensure the
located.
handle
is
positively
To remove the handle, press the button on the
handle with the thumb and pivot the handle
slightly upwards and towards the right to
remove from the bracket.
Protect your hands when removing
the grill pan handle.
Always remove the grill pan handle
during grilling.
To correctly locate the grill pan on the shelf,
ensure that the cut out on the underside of the
handle bracket locates over the front bar of the
shelf.
The Grill Pan must not be located in
the shelf runners.
To check the progress of the food being grilled,
the grill pan should be withdrawn on the shelf to
attend to food during cooking.
Ensure that the grill pan
supported when it is withdrawn.
is
14
HINTS AND TIPS
Most foods should be placed on the grilling
grid in the grill pan. This allows maximum
circulation of air by raising the food out of fats
and juices.
The grilling grid is reversible. Adjust the grid
height and grill pan runner position to allow
for different thicknesses of food. Position the
food close to the burner for faster cooking
and further away for more gentle cooking.
Food should be thoroughly dried before
grilling to minimise splashing. Brush lean
meats and fish lightly with a little oil or melted
butter to keep them moist during cooking.
The food should be turned over during
cooking as required. Do not use the grill to
keep food warm as it will continue to cook the
food.
The grill door must be left open when grilling.
For convenience the grill door can be left
ajar.
You may wish to preheat the grill on full
setting for a few minutes before sealing
steaks or browning food.
The grill compartment can be used to warm
plates when the main oven is on.
Do not place plates to warm under the grill
when it is lit as this may damage the plates.
15
Place food towards the centre of the grilling
grid. If food is outside this area it may require
rotating during cooking. Food such as
tomatoes and mushrooms requiring gentle
heat should be placed towards the edge of
the grid.
Place foods such as Shepherds pie and
cauliflower cheese on the grill shelf to brown.
GRILLING CHART
The chart below gives recommended cooking
times and shelf positions. Remember that these
are a guide and should be adjusted to suit
personal taste.
Note
Shelf positions are counted from the top
downwards.
FOOD
GRILL TIME
(Min)
SHELF GRID
POSITION
Bacon Rashers
2 - 3 each side
1
High
Beefburgers
6 - 10 each side
1
Low
Chicken Joints
15 - 20 each side
2
High
Chops - Lamb
- Pork
7 - 10 each side
10 - 15 each side
1
1
Low
Low
Fish - Whole Trout / Mackerel
Fillets - Plaice / Cod
8 - 12 each side
4 - 6 each side
1
1
Low
Low
Kebabs
10 - 15 each side
1
Low
Kidneys - Lamb
Pig
4 - 6 each side
8 - 10 each side
1
1
Low
Low
Liver
5 - 10 each side
1
Low
10 - 15 turn as
required
1
Low
3 - 6 each side
6 - 8 each side
7 - 10 each side
1
1
1
High
High
High
3 - 5 mins
2
-
- Lamb / Pig
Sausages
Steaks - Rare
Medium
Well Done
Browning e.g. au gratin,
lasagne, shepherd's pie
16
THE TOP OVEN
USES OF THE TOP OVEN
The top oven is the smaller of the two ovens.
It is convenient for smaller quantities or
convenience foods. It is important to refer to
the top oven cooking chart as a guide to shelf
positions and gas mark settings as these may
differ from previous cookers you may have
used.
PREHEATING
It is not necessary to preheat the oven for
casseroles.
For recipes needing high temperatures such as
bread, pastries, scones, soufflés etc. best
results are achieved if the oven is preheated for
20 minutes.
When cooking or reheating frozen or chilled
food read the instructions on the packaging.
GRILL / TOP OVEN
HOW TO LIGHT THE TOP
OVEN
1. Open the grill / top oven door.
2. Push in and turn the top oven / grill control to
the left to Gas mark 8.
When the burner has lit there will only be
small flames at first.
3. Adjust the control to the required Gas mark
setting.
4. Wait until the burner has a large flame.
5. Close the oven door.
GRILL / TOP OVEN
THINGS TO NOTE
The cooling fan for the controls will operate
as soon as the top oven / grill control is
turned. See page 6 for more information on
the operation of the cooling fan.
The oven light will illuminate.
The top oven cannot be controlled by the
automatic timer.
Do not place cookware over the
oven burner. This will damage the
oven and ovenware.
GRILL / TOP OVEN
TO TURN OFF THE TOP OVEN
1. Push in and turn the top oven / grill control to
the Off position. This is shown by a large dot.
17
TO FIT THE TOP OVEN SHELF
1
There are 3 shelf positions in the top oven.
Shelf positions are counted from the top
downwards.
2
3
The shelf should be fitted with the straight rods
uppermost on the frame and the forms towards
the back of the oven.
If not fitted correctly the anti-tilt and safety stop
mechanism will be affected.
Back of the oven
Straight Rods
HINTS AND TIPS
There are zones of heat within the oven. The
temperature in the middle is the gas mark you
have chosen. The top of the oven is slightly
hotter and the lower shelf slightly cooler.
You can only cook on one shelf when using
the top oven.
There should always be at least 2.5cm (1")
between the top of the food and the grill
burner. This gives best cooking results and
allows room for rise in yeast mixtures,
Yorkshire puddings etc. When cooking cakes,
pastry, scones bread etc., place the tins or
baking trays centrally on the shelf.
1
2
3
Leave a gap of 13mm (½") between all
dishes and the oven sides so the heat can
circulate properly.
Do not push dishes too far back as it will
burn if it overhangs the burner flames.
If you use a baking tray larger than the
recommended size of 12" x 9", (30cm x
25cm), you may need to turn it around during
cooking.
Where a larger quantity of food is to be
cooked we recommend you use the main
oven.
The material and finish of the baking tray and
dishes will affect the degree of base browning
of the food. Enamelware, dark, heavy or
non-stick utensils increase base browning.
Shiny aluminium or polished steel trays
reflect the heat away and give less base
browning.
For economy leave the door open for the
shortest possible time, particularly when
placing food into a pre-heated oven.
18
Frame
TOP OVEN COOKING CHART
The Gas mark settings are intended as a guide only. It may be necessary to increase or decrease the
settings to suit individual preferences and requirements.
Note: Shelf positions are counted from the top downwards.
FOOD
Viennese Biscuits
Bread
Bread Rolls / Buns
Cakes:
Small & Queen
Sponges
Victoria Sandwich
Madeira
Rich Fruit
Christmas
Gingerbread
Meringues
Flapjack
Shortbread
Baked Custard
Casseroles : Beef / Lamb
Chicken
Convenience Foods
Fish
Fish Pie - potato topped
Fruit Pies, Crumbles
Milk Puddings
Pasta / Lasagne etc.
Pastry : Choux - Eclairs/profiteroles
Flaky / Puff pies
Shortcrust Mince pies
Meat pies
Quiche, Tarts, Flans
Roast Meat / Poultry
Scones
Shepherds Pie
Soufflés
Vegetables : Baked Jacket Potatoes
Roast Potatoes
Yorkshire Puddings - Large
-Individual
SHELF POSITION
GAS MARK SETTING
3
2
2
2
2
2
2
2
3
3
3
2
2
2
3
3
2
2
2
2
2
2
2
2
7
7
7
5
4
4
4
2
2
2
1
5
2
3
3
4
According to Manufacturers Instructions
5
7
6
2
6
4
7
2
2
2
3
2
2
2
2
2
2
2
5
6
6
5
7
7
5
5
6
7
7
19
THE MAIN OVEN
USES OF THE MAIN OVEN
The main oven is particularly suitable for
cooking larger quantities of food. The main
oven also includes a Slowcook feature. It is
important to refer to the main oven cooking
chart as a guide to shelf positions and gas mark
settings as these may differ from previous
cookers you may have used.
PREHEATING
It is not necessary to preheat the oven for
casseroles.
For recipes needing high temperatures such as
bread, pastries, scones, soufflés etc. best
results are achieved if the oven is preheated for
20 minutes.
When cooking or reheating frozen or chilled
food read the instructions on the packaging.
MAIN OVEN
HOW TO LIGHT THE MAIN
OVEN
1. Open the oven door.
2. Push in the main oven control and turn it to
gas mark 9.
3. Adjust the control to the required gas mark
setting.
4. Wait until the burner has a large flame.
5. Close the oven door.
MAIN OVEN
THINGS TO NOTE
The oven light will come on when the oven
control is turned.
The cooling fan for the controls may operate
after a time. See page 6 for further details on
the operation of the cooling fan.
If an automatic programme has been set, the
oven light does not come on until the cook
time begins.
Do not place cookware over the
oven burner. This will damage the
oven and ovenware.
MAIN OVEN
TO TURN OFF THE MAIN
OVEN
1. Push in the control knob and turn it to the Off
position. This is shown by a large dot.
20
TO FIT THE MAIN OVEN SHELVES
1
There are 14 shelf positions in the main oven.
Shelf positions are counted from the top
downwards.
14
Back of the oven
The shelves should be fitted with the straight
rods uppermost on the frame and the forms
towards the back of the oven. If not fitted
correctly the anti-tilt and safety stop mechanism
will be affected.
Straight Rods
HINTS AND TIPS
There are zones of heat within the oven. The
temperature in the middle is the gas mark you
have chosen. The top of the oven is slightly
hotter and the lower shelf slightly cooler.
Use the heat zones when cooking foods
requiring different temperatures all at the
same time.
When cooking more than one tray of similar
items, for example cakes or biscuits, swap
the trays round during cooking. Alternatively
remove the top tray when the food is cooked
and move the lower tray to the higher shelf to
finish cooking.
It is recommended that when baking larger
quantities, the shelf positions should be
evenly spaced to suit the load being cooked.
A slight increase in cooking time may be
necessary.
The material and finish of the baking tray and
dishes will affect the degree of base browning
of the food. Enamelware, dark, heavy or
non-stick utensils increase base browning.
Shiny aluminium or polished steel trays
reflect the heat away and give less base
browning.
21
Frame
For economy leave the door open for the
shortest possible time, particularly when
placing food into a pre-heated oven.
ROASTING
For best results we recommend open roasting
using minimal fat or oil to prevent splashing.
It is not necessary to cover meat or poultry or
wrap food in foil when roasting as this restricts
the circulation of heat and will lead to extended
cooktimes.
If you are using a roasting bag or cover chicken
breast with foil, be prepared to allow an extra
10 - 15 minutes for each 1/2kg (1lb).
When cooking large items such as turkeys, the
use of foil may be required to prevent the
breast becoming dry before the rest of the bird
is fully cooked.
22
MAIN OVEN COOKING CHART
The Gas mark settings are intended as a guide only. It may be necessary to increase or decrease the
settings to suit individual preferences and requirements.
Note: Shelf positions are counted from the top of the oven downwards.
FOOD
SHELF POSITION
GAS MARK
SETTING
Viennese Biscuits
Bread
Bread Rolls / Buns
Cakes:
Small & Queen
Sponges
Victoria Sandwich
Madeira
Rich Fruit
Christmas
Gingerbread
Meringues
Flapjack
Shortbread
Baked Custard
Casseroles : Beef / Lamb
Chicken
Convenience Foods
7
10
10
5 & 11
5 & 11
5 & 11
7
9
10
8
14
7
7
10
10
10
7
Fish
Fish Pie - potato topped
Fruit Pies
Crumbles
Milk Puddings
Pasta / Lasagne etc.
Pastry : Choux - Eclairs/profiteroles
Flaky / Puff pies
Shortcrust Mince pies
Meat pies
Quiche, Tarts, Flans
Roast Meat / Poultry
Turkey
Scones
Shepherds Pie
Soufflés
Vegetables : Baked Jacket Potatoes
Roast Potatoes
Yorkshire Puddings - Large
- Individual
7
8
4 & 10
6
10
7
5
7
7
4
5 & 11
7
9
14
5 & 11
8
7
7
10
5
5
7
7
7
5
5
4
4
2
2
2
1-2
5
2
3
3
4
According to
Manufacturers Instructions
5
7
6
5
2
5
4
7
6
5
6
5
5
5
7
7
5
5
6
7
7
23
SLOWCOOK FEATURE
S
USES OF SLOWCOOK
Slowcooking in the main oven allows most
foods to be cooked at a low temperature over a
number of hours. A variety of foods, particularly
cheaper cuts of meat can be cooked in this way
making them tender, tasty and succulent.
This feature is most convenient when used in
conjunction with the automatic timer as there is
no need to be present at the start of cooking.
MAIN OVEN
HOW TO USE SLOWCOOK
1. Open the main oven door.
2. Push in the main oven control and turn it to
gas mark 9. When the burner has lit there will
only be small flames at first.
3. Turn the control to the Slowcook setting. S
4. Wait until the burner has a large flame.
5. Close the oven door.
THINGS TO NOTE
The oven light will come on when the oven
control is turned.
The cooling fan for the controls may operate
after a time. See page 6 for further details on
the operation of the cooling fan.
If an automatic programme has been set, the
oven light does not come on until the cook
time begins.
MAIN OVEN
Do not place cookware over the
oven burner. This will damage the
oven and ovenware.
HINTS AND TIPS
Always cover food with a close fitting lid or tin
foil.
Do not re-heat food using the slow cook
function.
Slow cooked food should be eaten as soon
as possible after cooking. It is not advisable
to allow food to cool down slowly.
It is recommended that vegetable dishes,
sponge and suet puddings are prepared just
prior to cooking.
A complete meal can be cooked using slow
cook function.
Most foods should be cooked on the middle
shelf. Use shelf position 9 for large joints and
stews. Ensure dishes are evenly spaced to
allow for maximum circulation around food.
Thicken casseroles by tossing meat in flour
first or by blending flour with water and
adding at the end.
Pastries, breads and biscuits are not suitable
for slow cooking.
Adjust seasoning at the end of the cook time.
Thaw frozen foods thoroughly before
cooking.
24
MEAT, FISH AND POULTRY
Prime cuts of meat for roasting are better not
slow cooked as flavours are retained to their
fullest when roasting.
Do not Slowcook joints of meat over 6lb
(2.7kg) in weight.
Only Slowcook joints of pork if you can make
sure by using a meat thermometer that the
temperature inside the joint is at least 88°C.
Do not Slowcook poultry over 4lb 8oz (2kg) in
weight.
Cook stuffing separately.
Do not Slowcook more than one 2lb (1kg)
meat stew in the oven at the same time when
slow cooking. Thicken after cooking with a
little cornflour and water if desired.
All frozen meat/poultry should be thoroughly
thawed before preparing for slow cooking.
Cooking times
Small items e.g. chops
3 - 4 hours
Small joints, stews
6 - 8 hours
Large joints
7 - 9 hours
Fish
2 - 3 hours
VEGETABLES
Cut vegetables into thin slices or small cubes
as they can take a long time to cook.
To prevent potatoes discolouring, cook
immediately after preparation and add a few
drops of lemon juice.
When cooking vegetables in a casserole,
place them under the meat to keep them
immersed in the gravy/sauce.
Cook for up to 6 hours.
MILK AND MILK PRODUCTS
Cream may curdle and separate during a
long cook time. Add cream at the end e.g. to
a soup, just before serving.
Place a baked custard in a bain-marie or
water bath and cover the tin with foil.
Cook for 2 - 4 hours
25
PASTA AND RICE
Cook pasta on the hob and add to the dish at
the end of the cook time.
Rice should be the 'easy cook' type. Use
250ml (½ pint) stock to 100g (4oz) rice.
Cooking time up to 6 hours.
DRIED BEANS AND FRUIT
Soak overnight prior to cooking.
DRIED RED KIDNEY BEANS AND ALL
OTHER VARIETIES OF BEANS SHOULD
BE RINSED, COVERED WITH FRESH
WATER IN A SAUCEPAN ON THE HOB
AND BROUGHT TO THE BOIL FOR AT
LEAST 10 MINUTES BEFORE DRAINING
AND ADDING TO THE DISH.
Canned beans may be placed in the dish with
other raw ingredients as they have already
been cooked.
PRESERVES
Only the softening of fruit can be carried out
using slow cook. The jam or marmalade must
be boiled up on the hob.
Chutney may thicken sufficiently after slow
cooking if left to stand or may require boiling
on the hob.
26
CARE AND CLEANING
For hygiene and safety reasons this
gas appliance must be kept clean.
A build up of fat or other foodstuffs
could cause a fire.
Before cleaning the appliance
always allow the cooling fan for the
controls to cool the appliance down
before switching off the electricity
supply.
CLEANING MATERIALS
Before using any cleaning materials on your
appliance, check that they are suitable and that
their use is recommended by the manufacturer.
Cleaners that contain bleach should NOT be
used as they may dull the surface finishes.
Harsh abrasives should also be avoided.
CLEANING THE OUTSIDE OF THE
APPLIANCE
DO NOT use abrasive cleaning materials or
scourers on the outside of the appliance as
some of the finishes are painted and damage
may occur. Regularly wipe over the control
panel and oven doors using a soft cloth well
wrung out in warm water to which a little
washing up liquid has been added.
Do not attempt to remove any of the
control knobs from the panel as
this may cause damage.
27
CLEANING THE OUTER AND
INNER DOOR GLASS PANELS
To prevent damaging or weakening
the door glass panels avoid the use
of the following:
l Household
detergents
and
bleaches
l Impregnated pads unsuitable for
non-stick saucepans
l Brillo/Ajax pads or steel wool
pads
l Chemical oven pads or aerosols
l Rust removers
The outer oven door
removable for cleaning.
glass
panels
are
TO REMOVE THE OUTER GLASS
1. Open the oven door slightly to gain access to
the two cross head screws on the top of the
oven door.
Grill Door Trim
2. Loosen the two screws using a Pozidrive
screwdriver.
3. Holding the door glass securely in place with
one hand remove the screws and washers
with the other hand.
The screws and washers retain the trim on
the top of the grill door. Note the position of
the trim on the door.
4. Holding the door and glass with one hand,
gently pull towards you and slightly lift the
door glass with the other hand to disengage
the panel from the location point at the
bottom of the door. Gently release the door to
close it.
5. Clean the outer and inner glass using hot
soapy water or Hob Brite. Should the inner
face of the outer door glass be heavily soiled
it is recommended that soapy water with a
high concentration of soap is used. To
prevent streaking a glass cleaning spray may
be applied and the glass polished with a soft
cloth. Ensure that all parts are well rinsed
and thoroughly dry before attempting to
replace the outer door glass.
If the door glass panel becomes
chipped or has deep scratches the
glass will be weakened and must be
replaced to prevent the possibility of
the panel shattering. Please contact
your local Service Centre who will
be pleased to advise further.
28
TO REPLACE THE OUTER
DOOR GLASS
1. Holding the door glass panel with both hands,
gently place the locators into the holes of the
brackets at the bottom of the oven door.
2. Holding the door glass with your left hand,
use your right hand to open the oven door.
Bring the door gently towards the glass panel
ensuring the screw location holes line up.
3. Place the trim in the correct position on the
top of the grill door.
4. Hold the glass in place with one hand and
insert the cross head screws with washers
into the location holes with the other hand.
Give the screws one turn to ensure the glass
is secure.
5. Tighten the screws positively with a Pozidrive
screwdriver before closing the oven door.
DO NOT attempt to use the oven
without the glass being in place.
TO CLEAN THE INNER GLASS
DOOR
The inner glass door is not removable. Clean
using hot soapy water or Hob Brite and a soft
cloth. DO NOT use abrasives as they may
damage the glass or seal.
CLEANING INSIDE THE OVENS
The oven top and sides are coated with a
Stayclean finish. The back panels are vitreous
enamelled.
The Stayclean areas in the ovens should not be
cleaned manually. See Care of Stayclean
Surfaces on page 30.
The main oven base and back panels can be
cleaned using normal oven cleaners or aerosol
oven cleaners with care. Ensure that the
manufacturers instructions are followed and
protect the oven burner with foil to prevent it
from becoming blocked. Do not spray aerosol
cleaners through the aperture in the back panel
as the cavity behind is coated with a Stayclean
finish.
Take care when cleaning round the back panel
aperture.
Do not use any cleaning agents or scrapers on
the oven roof, sides and door seal.
Damage will occur if soap impregnated steel
wool pads, aerosol cleaners or any abrasive
cleaners are used on the Stayclean finish.
29
TO REMOVE THE WIREWORK
RUNNERS
The wirework runners in both ovens can be
removed for cleaning.
1. Remove all shelves and furniture from the
oven.
2. Hold the wirework at the bottom and gently
pull towards the centre of the oven.
3. Unhook the runner at the top and remove it
from the cavity.
4. To replace, hook the wirework back into the
oven sides.
Ensure that the wirework runners
are firmly in place before refitting the
oven shelves.
CLEANING THE SHELVES,
WIREWORK RUNNERS AND OVEN
FURNITURE
Soak the oven shelves, wirework runners and
grilling grid in hot soapy water if heavily soiled,
they will then clean more easily. If the shelves
are heavily soiled a soap impregnated steel
wool pad can be used.
The grill pan and meat tin can be cleaned using
a soap impregnated steel wool pad.
All items of grill and oven furniture are
dishwasher safe with the exception of the grill
pan handle.
CARE OF STAYCLEAN SURFACES
The top and sides of both ovens are coated
with a Stayclean finish. They should not be
cleaned manually.
During normal use the Stayclean finish will
become splashed with fats and food residues.
When the Oven Cleaning Cycle is selected the
Stayclean surfaces burn off any soilage. See
page 31. Regular use of the Oven Cleaning
Cycle function will help to keep the panels in
good condition.
30
MAIN OVEN
THE OVEN CLEANING CYCLE
1. Remove oven shelves, wirework runners and
bakeware from oven.
2. Push in and turn the oven control to mark 5
for 30 minutes.
3. Turn the temperature up to mark 7 for 2
hours or until the oven is presentably clean.
Some staining will remain.
30 MINS
THINGS TO NOTE
2 HOURS
TOP OVEN
The cooling fan for the controls will operate
after a short time when the oven cleaning
cycle is selected. It may run on after the
controls are switched off until the appliance
has cooled. See page 6 for more details on
the operation of the cooling fan.
30 MINS
HINTS AND TIPS
Slight discolouration and polishing of the
Stayclean surfaces may occur in time, but
this will not affect their self cleaning
properties.
A good time to use the oven cleaning cycle is
after the weekly roast.
If you do a lot of roasting and very little
baking you should follow the cleaning cycle
every week. If you roast very little you will
only need to follow the cleaning cycle every 2
- 3 weeks.
Follow the recommendations below to keep
soilage to a minimum.
COOKING TO REDUCE SOILAGE
Cook at the recommended temperatures.
Higher temperatures during roasting will
increase soilage. Try cooking at lower
temperatures for an increased length of time,
you will save energy and often the joint is
more tender.
Use minimal, if any, extra oil or fat when
roasting meat, potatoes only require brushing
with fat before cooking. Extra fat in the oven
during roasting will increase splashing and
soilage.
It is not necessary to add water to the meat
tin when roasting. The water and the fat
juices from the joint create excessive
splattering during cooking, even at normal
temperatures,
as
well
as
causing
condensation.
31
2 HOURS
Covering joints during cooking will also
prevent splashing onto the interior surfaces.
Removing the covering for the last 20-30
minutes will allow extra browning if required.
Some large joints and turkeys especially
benefit by this method of cooking, allowing
the joint to cook through before the outside is
over-browned.
REPLACING AN OVEN LIGHT
BULB
Isolate the appliance from the
electricity supply before replacing
the bulb.
The type of bulb required is a 300°C, 25 watt
small Edison Screw.
1. Make sure the appliance is cool before you
replace a bulb.
2. Open the oven door and remove the shelves
and wirework runners.
Instructions on how to remove the wirework
runners are given on page 30.
3. Pull the glass bulb cover towards you and
then pull it off. If necessary use a screwdriver
to carefully lever off the cover, taking care not
to damage the oven cavity.
4. Unscrew the bulb by turning it to the left.
5. Fit a new bulb and then replace the glass
bulb cover.
6. Refit the wirework runners and replace the
oven shelves.
7. Restore the appliance to the electricity supply
and reset the time of day.
32
SOMETHING NOT WORKING
Please carry out the following checks on your appliance before calling a Service Engineer. It may be
that the problem is a simple one which you can solve yourself without the expense of a service call.
If our Service Engineer finds that the problem is listed below you will be charged for the call whether or
not the appliance is under guarantee.
PROBLEM
The grill, ovens and timer do not work
POSSIBLE SOLUTION
Check that the appliance is switched on at the
wall.
Check that there has not been a power failure.
If the electricity supply has been interrupted or
you have switched the oven off at the wall, the
grill may have cut out before the cooling fan
has cooled the appliance down. Switch the
appliance on at the wall until the cooling fan
has cooled it down.
Check that there is not a problem with your
gas supply. You can do this by making sure
that other gas appliances such as your central
heating or gas fire are working.
The Grill and Top Oven work but the Main
Oven does not
Check that the timer is set for manual
operation. See page 10.
The Grill sparks in use
Ensure that the grill door is open when grilling.
If the grill door is closed whilst the burner is lit
it will automatically re-light when the door is
opened.
Always light the burner before placing the grill
pan and food under the grill.
The Grill does not work
Ensure the cooling fan is running when the
grill is on. If the cooling fan fails, the grill will
not work.
Contact your nearest Service Centre.
The timer does not work
Check that the instructions for the operation of
the timer are being closely followed.
The oven or grill burner flame is unstable /
noisy
Check that the burner flames stabilise after a
few minutes. The appliance may need to
adjust to room temperature.
33
The oven is not cooking evenly
Check that the appliance is correctly installed
and is level.
Check that the recommended Gas mark
settings and shelf positions are being used.
If you use a tin or tray larger than the
recommended size be prepared to turn it
round during cooking. If cooking a large item
be prepared to turn it round during cooking.
The oven light fails to illuminate
The oven light bulb may need replacing see
page 32.
If the Main Oven is set for automatic cooking
the light will illuminate when the cook time
begins.
Food is cooking too quickly or too slowly
Check that the recommended Gas mark
settings and shelf positions are being used.
See page 23. Be prepared to adjust the gas
mark up or down by one setting to achieve the
results you want.
34
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the heading 'Something Not
Working'.
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for
in-guarantee service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Electrolux appliance or further information on Electrolux products, please
contact our Customer Care Department by letter or telephone at the address below;
Customer Care Department
Electrolux
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 0870 5 950950 (*)
*calls to this number may be recorded for training purposes.
35
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance
or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will,
at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on
condition that:
l
The appliance has been correctly installed and used only on the electricity supply stated on the
rating plate.
l The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer's instructions.
l The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any
person not authorised by us.
l All service work under this guarantee must be undertaken by your local Service Force centre.
l Any appliance or defective part replaced shall become the Company's property.
l This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
l Damage or calls resulting from transportation, improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
l Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances
outside the United Kingdom.
l Appliances found to be in use within a commercial environment, plus those which are subject to
rental agreements.
l Products of Electrolux manufacture which are not marketed by Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new
home subject to the following qualifications:
l The guarantee starts from the date you first purchased your product.
l The guarantee is for the same period and to the same extent for labour and parts as exists in the
new country of use for this brand or range of products.
l This guarantee relates to you and cannot be transferred to another user.
l Your new home is within the European Community (EC) or European Free Trade Area.
l The product is installed and used in accordance with our instructions and is only used domestically,
i.e. a normal household.
l The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details
of your new home. They will then ensure that the local Service Organisation is aware of your move and
able to look after you and your appliances.
France
Germany
Italy
Sweden
UK
Senlis
Nürnberg
Pordenone
Stockholm
Slough
+33 (0) 3 44 62 20 13
+49 (0) 800 234 7378
+39 (0) 800117511
+46 (0) 20 78 77 50
+44 (0) 1753 219898
36
TECHNICAL DETAILS
Loading Info:
Grill Burner
Natural Gas
L.P. Gas
Heat Input
2.8kW (9554 Btu/h)
2.8kW 201 g/h
Injector Marking
123
089
Heat Input
1.7kW (5800 Btu/h)
1.7k/W 122 g/h
Injector Marking
095
Flame Supervision Device
Diamond 'H' GSD 100/48
Diamond 'H' GSD 100/49
Thermostat
Sourdillon 63503/982
Sourdillon 64063/982
Thermostat By-Pass Marking
Fixed Internal
Fixed Internal
Heat Input
1.7kW (5800 Btu/h)
1.7kW 122 g/h
Injector Marking
095
Flame Supervision Device
Diamond 'H' GSD 100/28
Thermostat
Diamond 'H' 1100 - 122/B2 Diamond 'H' 1100 - 123/B2
Thermostat By-Pass Marking
74
Top Oven*
Main Oven
Diamond 'H' GSD 100/30
79
Oven Light:
0.05kW
Control Cooling Fan
0.020kW
Timer:
0.005kW
Height:
Appliance 760 mm
Width:
593 mm
Depth:
(excluding handles and knobs)
550 mm
Weight:
49kg
Connection:
Gas
Rear top right hand side of appliance Rc½ (½" B.S.P.
Female)
Electric
Installed 720 mm
230/240 Volt A.C. 50Hz Mains 3 core cable and moulded
plug fused to 3 amps.
* Cannot be used at the same time as the grill burner
IMPORTANT - SAFETY REQUIREMENTS
This appliance must be installed in accordance with the Gas Safety (Installation and Use) Regulations
Current Editions. Detailed recommendations are contained in the following British Standard Codes of
Practice - BS.6172, BS.5440: Part 2 and BS.6891. All British Standards must be 'Current Editions'.
PROVISION FOR VENTILATION
This appliance is not connected to a combustion products evacuation device. It shall be installed and
connected in accordance with the current installation regulations. Particular attention shall be given to
the relevant requirements regarding ventilation.
The room containing the appliance should have an air supply in accordance with BS. 5440: Part 2
Current Edition. All rooms require an openable window or equivalent and some rooms will require a
permanent vent as well. For room volumes up to 5m³ an air vent of 100cm² is required: for room
volumes between 5m³ and 10m³ an air vent of 50cm² is required. If the room has a door that opens
directly to the outside, no air vent is required. For room volumes that exceed 11m³ no air vent is
required. If there are other fuel burning appliances in the same room, BS.5440: Part 2 Current Edition
should be consulted to determine the requisite air vent requirements.
Prolonged intensive use of the appliance may call for additional ventilation, for example opening a
window, or more effective ventilation, for example increasing the level of mechanical ventilation where
present.
37
INSTALLATION INSTRUCTIONS
THINGS YOU NEED TO KNOW
WARNINGS:
In the interest of safety this appliance must
be installed and / or serviced by a competent
person (Corgi registered). Safety may be
impaired if installation is not carried out in
accordance with these instructions.
This appliance must be earthed.
Do not remove the screws from the earth tab
extending from the oven mains terminal block
(Fig. 1).
Before connecting the appliance make sure
that the gas type and the voltage of your
electricity supply is the same as that indicated
on the rating plate. The rating plate can be
seen on the rear panel of the appliance.
Fig.1
Do not alter the electrical circuitry of this
appliance.
NOTE: HOUSE CIRCUIT
Earth leakage / continuity tests must be carried
out before the appliance is connected to the
mains supply and re-checked after fitting.
NOTE: It is good practice to:
Fit an Earth Leakage Circuit Breaker to your
house wiring.
Wire your appliance to the latest IEE
regulations.
THINGS TO NOTE
LOCATION OF APPLIANCE
Fig.2
The appliance may be located in a kitchen, a
kitchen/diner or bedsitting room, but not located
in a bathroom or shower room.
L.P.G. cookers MUST NOT be installed below
ground level i.e. in a basement or aboard any
boat, yacht or other vessel.
It is essential that there is a minimum
clearance of 2mm between the top surface
of the appliance and the inside top of the
cabinet.
This appliance is designed to be fitted
between cabinets with the recommended
dimensions as shown in Figs. 2 and 3.
Fig.3
38
INSTALLATION INSTRUCTIONS
This appliance must not be installed on a
wooden base.
The dimensions given provide adequate air
circulation around the unit within the cabinet,
ensuring compliance with BS EN30.
GETTING THINGS READY
PREPARING CABINET FOR FITTING OVEN
Make sure the cabinet is the correct size for
the appliance to be fitted (Ref. Fig. 4).
If the size is between 605-610*mm, then the
cabinet should be modified so that at the
screw fixing points the recommended
dimension of at least 600-605mm is
maintained. The modification should ideally
be localised to ensure that after screw fitment
the oven is securely fixed into position.
The adjacent cabinets must be stable and
firmly secured to the wall or floor. If
necessary, make arrangements to ensure the
work surface below which the oven will rest is
level.
Mark the centre of the aperture into which the
appliance is to be fitted onto the plinth board.
Remove the plinth board from in front of the
cabinets.
Cut the required ventilation slot in the plinth
as detailed in Fig.5.
Drill two pilot screw holes into the sides of the
adjacent cabinets, in the positions indicated
by Fig. 4.
Fit the appliance mounting brackets using the
two holes indicated in Fig. 6 to the adjacent
cabinets ( Ref. Fig.4 & 7 )
Check that the mounting brackets are level.
They can be adjusted if necessary by using
the extra holes at the ends of the brackets.
Once the brackets are level, drill a pilot hole
through the central hole in the bracket and fit
the remaining screw.
Fig.4
Fig.5
Fig.6
Fig.7
39
INSTALLATION INSTRUCTIONS
FLEXIBLE PIPE INSTALLATION
FITTING THE APPLIANCE AND CABINET
It is recommend that a 3/8", 1100mm long
angled flexible hose (BFS), and a ½" straight
socket (BFS) be used for the installation.
However, any approved hose of the right length
can be used.
IMPORTANT: Flexible tubing used must
comply with BS 669 current editions. L.P.G.
flexible connections must be of a type suitable
for L.P.G. and capable of operation up to
50mbar and carry a red stripe, band or label.
NOTE: Only liquid sealants can be used in
threaded gas connections. Do not use P.T.F.E.
tape.
1 Make suitable arrangements for gas and
electric supplies into the installation site.
2 When unpacking the appliance keep it on
its polystyrene base until it is put into the
cabinet to avoid damage.
NOTE: It is imperative that the appliance
is left in the base to protect both the
appliance and the floor.
3 If the gas supply bayonet and wall fixing
bracket are to be located behind the
appliance it must be located in the shaded
area as indicated in Fig.8.
4 Connect flexible hose to the gas inlet supply
block see Fig.8. The hose should be long
enough to allow the appliance to be
withdrawn from the cabinet.
5 Position the appliance in front of the cabinet
and run the supply cable (See Connection
to Electricity Supply) through the cabinet
and connect to the junction box or socket.
Ensure that the supply is isolated at this
stage. Connect flexible hose to the bayonet
connector.
580
280
120
Fig.8
40
120
INSTALLATION INSTRUCTIONS
CONNECTION TO ELECTRICITY
SUPPLY
WARNING: This appliance must be
earthed, do not earth this appliance
to the gas supply piping.
This appliance must be connected to a isolated
220V-240V
a.c.
50Hz
supply
which
incorporates a 3 ampere fuse. If any other type
of plug is used it should incorporate a 5 ampere
fuse in either the plug or adapter or at the
distribution board. The appliance is supplied
with 2 metres (6.5 ft) of 5 ampere 3 core cable
fitted with a moulded plug. If this proves
insufficient to allow the appliance to be plugged
into the nearest supply socket, the supply cable
can be either extended by using a B.E.A.B.
approved 3-way sealed flex connector with
integral flex clamps.
DO NOT EXTEND THE CABLE USING
PLASTIC OR CERAMIC CONNECTION
TERMINAL BLOCKS AND/OR INSULATION
TAPE.
Should the supplied cable be required to be
threaded through small apertures in the
cabinets it can be removed from the mains
plug.
If the supplied moulded plug is cut off
dispose of it safely as it will be a shock
hazard if inserted into a 13 amp socket
elsewhere in the house.
To fit a 3 pin 13 amp plug to the end of the
appliance cable (Fig.9). Connect the wires as
follows:
BROWN to the live terminal.
BLUE to the neutral terminal.
GREEN / YELLOW to the earth terminal.
Fig.9
41
INSTALLATION INSTRUCTIONS
As the colours of the wires in the mains lead of
this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is GREEN and YELLOW must
be connected to the terminal in the plug which
is marked with the letter 'E' or by the earth
symbol
or coloured GREEN or GREEN and
YELLOW.
The wire which is coloured BLUE must be
connected to the terminal which is marked with
the letter 'N' or coloured black.
The wire which is coloured BROWN must be
connected to the terminal which is marked with
the letter 'L' or coloured RED.
FIT A 3 AMP FUSE TO THE PLUG FUSE
HOLDER
Turn on Gas and Electric supplies
Carry out a soundness test.
NOTE: HOUSE CIRCUIT
Earth leakage / continuity tests must be carried
out before the appliance is connected to the
mains supply and re-checked after fitting.
Switch off electric supply.
INSTALLATION BETWEEN
CABINETS
Fig.10
Lift the appliance into the cabinet making
sure the hose and cable are not trapped.
Push the appliance as far back as it will go.
N.B. Two people will be required to carry
out the lifting procedure.
Warning: Do not attempt to lift this
appliance by the handle(s).
Centralise and fix the appliance to the
underside of the worktop using the two
stability screws provided, in the position
indicated in Fig.10.
Refit the plinth board.
Fig.11
Place the top trim with the cork washers
uppermost flush with the edge of the
worksurface (see Fig.11) and screw into
position using the screws supplied with the
appliance.
Switch on the appliance then refer to the
operating instructions in the following pages.
Carry out gas soundness check.
Ensure the owner is given these operating
instructions.
CHECKING ELECTRICAL
CONNECTIONS
Confirm the appliance is correctly connected
by switching on and observing the various
oven functions .
The electronic timer will flash on and off.
42
INSTALLATION INSTRUCTIONS
PRESSURE TESTING
To pressure test connect the pressure gauge to
the main oven injector
1 Check the supply pressure by turning the
grill on and oven thermostat to Mark 9. Then
turn on the electricity supply. Allow the grill
burner to light.
The pressure should be:
Natural Gas 20mbar
L.P.G. Gas The pressure must be set to
28mbar for use on butane or 37mbar for use
on propane.
2 Turn off the electricity supply and the
thermostat; disconnect the pressure gauge.
CHECKING THE GRILL
1 Place the grill pan containing the grid under
the grill burner.
2 With the grill door open, turn on the grill tap,
check that there is a spark from the ignition
system. This should continue until the
burner is alight.
3 There is a safety switch which shuts off the
gas supply to the grill burner when the door
is closed. Check that it is operational by
slowly closing the grill door, the gas supply
should be shut off to the burner before the
grill door is fully closed.
CHECKING THE OVENS
The ovens should be tested separately.
1 Set the clock as described on page 10, the
clock is now ready for manual operation.
2 Turn the oven thermostat knob to maximum
and check that there is sparking from the
ignition system. This should continue until
the oven burner is alight.
3 When the oven burner lights up the sparking
should cease, there should be a low gas
rate at first to the oven burner which is the
flame supervision device (F.S.D.) by pass
rate.
4 When the F.S.D. phial has heated up it
opens the F.S.D. valve and the main gas
stream flows to the burner.
5 Set the oven thermostat to Mk. 2, close the
oven door and check that after 10 minutes
the flame size has reduced.
6 Turn off the thermostat and check that the
oven flames go out.
43
NOTES
44
NOTES
45
NOTES
EDB876 - 311461706
46
NOTES
47
35
IMPORTANT NOTICE
In line with our continuing policy of research and development, we reserve the right to alter models and
specifications without prior notice.
This instruction booklet is accurate at the date of printing, but will be superseded if specifications or
appearance are changed.
ELECTROLUX
55 - 77 HIGH STREET,
SLOUGH,
BERKSHIRE,
SL1 1DZ
TELEPHONE 0870 5 950950
Part Number: 311461706
© Electrolux Household Appliances Limited 2001