ASSEMBLY & INSTALLATION
INSTRUCTIONS FOR # 25236
Please read carefully and save these instructions, as you may need them at a later date.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards.
If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.
ASSEMBLY AND INSTALLATION
1. Take the parts out of the mounting package . Screw the end of the NIPPLE (4) into the center hole of the
MOUNTING BRACKET (2) and thread both 1/8” IPS HEX NUT(5) several turns onto each end of the
NIPPLE(4) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the
SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING BRACKET
(2) assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING BRACKET (2) and the
MOUNTING SCREWS (3) provided. (See Fig. 1)
2. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY (15) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the midpoint of the outside threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface of the CANOPY (15). Remove the CANOPY (15) and tighten both 1/8” IPS HEX NUTS (5) down on the
MOUNTING BRACKET (2) and the SCREW COLLAR LOOP (6). (See Fig. 1)
3. Thread the FIXTURE LOOP(18) onto the NIPPLE(19) till tight. Pull the ARMS(21) so they are evenly spaced. Thread the CENTER TUBE(23) over the SWIVEL ASSEMBLY(20) till tight. Thread the ARMS
ASSEMBLY(26) over the CENTER TUBE(23) till tight. Slide the BUSH(24) over the SOCKER(25). to have the NIPPLE(27) through the hole at the ARM(21), fix it with the NUT SCREW(22). Pull the
ARMS(29) so they are evenly spaced. to have the NIPPLE(28) through the hole at the ARM(29), fix it with the NUT SCREW(22). Thread the NIPPLE(31) onto the COUPLING(30), secure with the hex nut. Slide the POLY COVER(32) over the NIPPLE(31), secure with the FINIAL(33). (See Fig. 2)
4. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17) onto the FIXTURE LOOP
(18). Slide the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP (6). Close the ends of the chain links. (See Fig. 1 and 2)
5. Unravel the fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) and thread them through every other link of the CHAIN (17) starting with the chain link attached to the FIXTURE LOOP (18). Feed the fixture lead wires(10 and 12) and FIXTURE GROUND WIRE (7) through the SCREW COLLAR
LOOP (6) and NIPPLE (4) assembly. Pull the fixture lead wire(10 and 12) and the FIXTURE GROUND
WIRE (7) upward to remove any excess slack. (See Fig. 1)
ASSEMBLY AND INSTALLATION (Continued)
6. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE
(9) to the SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the
RIBBED FIXTURE LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the
GROUND SCREW (14) of the MOUNTING BRACKET (2). (Note: Be sure to provide an extra
3” length of the GROUND WIRE(7).) Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY GROUND WIRE (8) using a WIRE CONNECTOR (13). Place wiring and connections inside the OUTLET BOX (1). (See Fig. 1)
7. Slide the CANOPY (15) and the THREADED RING(16) up the CHAIN(17). Place the CANOPY
(15) over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the SCREW COLLAR LOOP (6).(See Fig.1)
8. Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage specified on the fixture’s wattage rating label,
MAXIMUM 60W.
INSTALLATION IS NOW COMPLETED
FIG. 2
FIG. 1
1. OUTLET BOX
2. MOUNTING BRACKET
3. MOUNTING SCREW
4. NIPPLE
5. 1/8” IPS HEX NUT
6. SCREW COLLAR LOOP
7. FIXTURE GROUND WIRE
8. SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
10. SMOOTH FIXTURE LEAD
WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD
WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. FIXTURE LOOP
19. NIPPLE
20. SWIVEL ASSEMBLY
21. ARMS
22. NUT SCREW
23. CENTER TUBE
24. BUSH
25. SOCKET
26. ARMS ASSEMBLY
27. NIPPLE
28. NIPPLE
29. ARMS ASSEMBLY
30. COUPLING
31. NIPPLE
32. POLY COVER
33. FINIAL
