User guide | Elo TouchSystems 1524L Computer Monitor User Manual

User Guide
15" LCD Desktop Touchmonitor
1524L Series
Revision A
P/N 008549
Copyright © 2002 Elo TouchSystems Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written
permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves
the right to revise this publication and to make changes from time to time in the content hereof
without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo
TouchSystems, Inc.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.
iii
iv
Table of Contents
Chapter 1
Introduction
7
Product Description . . . . . . . . . . . . . . . . 7
Precautions . . . . . . . . . . . . . . . . . . . . 7
About the Product . . . . . . . . . . . . . . . . . 8
Chapter 2
Installation and Setup
9
Unpacking Your Touchmonitor. . . . . . . . . . . 9
Product Overview . . . . . . . . . . . . . . . . 10
Main Unit . . . . . . . . . . . . . . . . . . . 10
Rear View . . . . . . . . . . . . . . . . . . 10
Touch Interface Connection . . . . . . . . . . . 11
Installing the Driver Software . . . . . . . . . . 12
Installing the Serial Touch Driver . . . . . . . 13
Installing the Serial Touch Driver for Windows
XP, Windows 2000, Me, 95/98 and NT 4.0 13
Installing the Serial Touch Driver for MS-DOS
and Windows 3.1 . . . . . . . . . . . . . 14
Chapter 3
Operation
About Touchmonitor Adjustments
Front Panel Controls . . . . .
Controls and Adjustment . . . .
OSD Menu Functions . . . .
OSD Control Options. . . . .
Preset Modes . . . . . . . .
Power Management System .
Display Angle . . . . . . . . . .
15
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
15
16
17
17
18
19
20
20
Chapter 4
Troubleshooting
21
Solutions to Common Problems. . . . . . . . . 21
Appendix A
Appendix B
Care and Handling of Your Touchmonitor . . . . 26
Appendix C
Touchmonitor Specifications. . . . . . . . . . . 28
AccuTouch Touchscreen Specifications . . . 29
15" LCD Touchmonitor (ET1524L-XXWC-1)
Dimensions . . . . . . . . . . . . . . . . . . 30
v
Regulatory Information
Warranty
31
35
Index
37
Copyright © 1996, Borland International. All rights reserved. BORLAND CONFIDENTIAL
January 9, 2002 9:17 am (D:\Vera new\8549 15 in Econ AT User Guide\15 in Economy AT\15
in Econ ATTOC.fm)
vi
CHAPTER
1
INTRODUCTION
CHAPTER 1
Product Description
Your new touchmonitor combines the reliable performance of touch technology
with the latest advances in LCD display design. This combination of features
creates a natural flow of information between a user and your touchmonitor.
This LCD monitor incorporates 15” color active matrix thin-film-transistor
(TFT) liquid crystal display to provide superior display performance. A
maximum resolution of XGA 1024x768 is ideal for displaying graphics and
images. Other outstanding designs that enhance this LCD monitor’s
performance are Plug & Play compatibility, and OSD (On Screen Display)
controls.
NOTE
Some monitors do not have the touchscreen capability.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit. See Appendix B for more
information on touchmonitor safety.
1-7
About the Product
Your LCD Desktop Touchmonitor is a 15” XGA TFT color display with the
following features:
• The internal microprocessor digitally controls auto-scanning. For horizontal
scan frequencies between 31.5 KHz and 60.2 KHz, and vertical scan
frequencies between 56.3 Hz and 75.0 Hz. In each frequency mode, the
microprocessor-based circuitry allows the monitor to function at the
precision-of a fixed frequency.
• High contrast color TFT LCD display support resolution up to XGA
1024x768. Compatible with VGA, SVGA, XGA (non-interlaced) and most
Macintosh compatible color video cards.
• Power management system conforms to VESA DPMS standard.
• Supports DDC1/2B for Plug & Play compatibility.
• Advanced OSD control for picture quality adjustment.
• Detachable stand for wall-mounting application.
• Optional touch screen function.
For full Product Specifications refer to Appendix C.
1-8
User Guide
CHAPTER
2
INSTALLATION AND SETUP
CHAPTER2
This chapter discusses how to install your LCD touchmonitor and how to install
the driver software.
Unpacking Your Touchmonitor
Check that the following 7 items are present and in good condition:
Serial cable
VGA cable
LCD monitor
European power cable
Power cable US/Canada
CD and Quick Install
Guide
2-9
Product Overview
Main Unit
Rear View
2-10
User Guide
Touch Interface Connection
NOTE:
Before connecting the cables to your touchmonitor and PC, be sure that the computer
and touchmonitor are turned off.
1 Connect one end of the power cord to the monitor and the other end to the
outlet.
2 Connect one end of the video cable to the rear side of computer and the other
to the LCD monitor. Tighten by turning the two thumb screws clockwise to
ensure proper grounding.
3 Connect one end of the touchscreen (RS232) cable to the rear side of
computer and the other to the LCD monitor. Tighten by turning the two
thumb screws clockwise to ensure proper grounding. (optional module)
4 Press the power button on front panel to turn the monitor power on.
2-11
Installing the Driver Software
The driver software allows your touchmonitor to work with your computer.
Drivers are located on the enclosed CD-ROM for the following operating
systems:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
Your touchmonitor is plug-and-play compliant. Information on the video
capabilities of your touchmonitor is sent to your video display adapter when
Windows starts. If Windows detects your touchmonitor, follow the instructions
on the screen to install a generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.
2-12
User Guide
Installing the Serial Touch Driver
Installing the Serial Touch Driver for Windows XP, Windows
20001, Me, 95/98 and NT 4.0
NOTE:
For Windows 2000 and NT 4.0 you must have administrator access rights to install the
driver.
1 Insert the CD-ROM in your computer’s CD-ROM drive.
2 If the AutoStart feature for your CD-ROM drive is active, the system
automatically detects the CD and starts the setup program.
3 Follow the directions on the screen to complete the driver setup for your
version of Windows.
4 If the AutoStart feature is not active:
5 Click Start > Run.
6 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
7 Click Open, then OK to run EloCd.exe.
8 Follow the directions on the screen to complete the driver setup for your
version of Windows.
1. To install Windows 2000 and Windows XP, you must use the "update driver" method; you will not
find a setup.exe file within the download.
2-13
Installing the Serial Touch Driver for MS-DOS and
Windows 3.1
You must have a DOS mouse driver (MOUSE.COM) installed for your mouse
if you wish to continue using your mouse along with your touchmonitor in
DOS.
To install Windows 3.x and MS-DOS from Windows 95/98, follow the
directions below:
1 Insert the CD-ROM in your computer’s CD-ROM drive.
2 From DOS, type d:\EloDos_W31 to change to the correct directory on the
CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
3 Type install and press Enter to start the installation.
4 Align the touchscreen.
You must have already completed Steps 1 and 2 before proceeding.
To run the INSTALL program:
1 Type INSTALL at the DOS prompt in the directory containing the driver
install files.
2 INSTALL asks you to select the software to install. Then choose
d:\EloDos_W31 from the displayed list.
3 INSTALL also asks you for the paths to use during installation, or you may
use its defaults. INSTALL creates directories as necessary, and warns you if
they exist.
If you are updating your software, you may wish to specify the paths containing
the earlier versions, and overwrite the obsolete files. All executable programs
are upward compatible. For a list of differences from each previous version of
the drivers, be sure to select "Differences from Previous Versions" during the
installation process.
INSTALL updates your AUTOEXEC.BAT file with the drivers you select.
INSTALL makes a copy of your original AUTOEXEC.BAT file, called
AUTOEXEC.OLD. If you already have Elo driver commands in your
AUTOEXEC.BAT file, they will be commented out.
When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory
you specified. GO loads the touchscreen driver, runs the calibration program
ELOCALIB, and gives you some final instructions.
If you are using Windows 3.1, you will also calibrate the touchscreen within
Windows 3.1 with the Touchscreen Control Panel.
2-14
User Guide
CHAPTER
3
OPERATION
CHAPTER3
About Touchmonitor Adjustments
Your touchmonitor will unlikely require adjustment. Variations in video output
and application may require adjustments to your touchmonitor to optimize the
quality of the display.
For best performance, your touchmonitor should be operating in native
resolution, that is 1024x768 at 60k-75 Hz. Use the Display control panel in
Windows to choose 1024x768 resolution.
Operating in other resolutions will degrade video performance. For further
information, please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This
feature saves you from having to reset your choices every time you unplug or
power your touchmonitor off and on. If there is a power failure your
touchmonitor settings will not default to the factory specifications.
3-15
Front Panel Controls
Auto
Enter
7
6
User Guide
+
5
4
Menu/Exit
3
2
1
Control
Function
1
Power Switch
Turns the display system power on or off.
2
Power LED
Lights up to indicate the power is turned ON.
3
Menu/Exit
To enter or exit OSD manual.
4
+
5
−
6
Enter
7
Auto
To select the function item clockwise. To increase the value
of the parameter in the OSD you have selected for
adjustment.
To select the function item counter clockwise.To decrease
the value of the parameter in the OSD you have selected for
adjustment.
To enter the function in the OSD you have selected for
adjustment.
Auto-adjust
Enable/Disable
3-16
-
1. Press the Menu/Exit and Enter buttons at the same time
and hold for two seconds to enable/disable the OSD
functions. OSD default is enabled.
2. Press the Menu/Exit and Auto buttons at the same time to
enable/disable the power lock function.
Controls and Adjustment
OSD Menu Functions
To Display and Select the OSD Functions:
1 Press Menu/Exit key to activate the OSD menu.
2 Use + or - to move clockwise or counterclockwise through the menu. Then
press the Enter key, the parameter will be highlighted when selected.
3 Then use + or - to increase or decrease the value of the parameter, or make
selection between different options.
4 To quit the OSD screen at any time during the operation, press Menu/Exit
key. If no keys are pressed for a short time period, the OSD automatically
disappears.
NOTE:
The OSD screen will disappear if no input activities are detected for 45 seconds.
3-17
OSD Control Options
Control
Description
Brightness
Contrast
H-Position
V-Position
Phase
Increases or decreases brightness
Clock
OSD H-Position
The dot clock is fine-adjusted after auto adjust.
OSD V-Position
Color Balance
Auto-Adjust
Recall Defaults
OSD Language
Information
3-18
User Guide
Increases or decreases contrast
Moves the screen left or right
Moves the screen up or down
Increases or decreases the snow noise of the image after auto
adjustment is made.
Moves the OSD position horizontally on the screen. When the +
button is pressed, the OSD control menu will move to the right
side of the screen. Likewise, when the - button is pressed, the
OSD control menu will move to the left side.
Moves the OSD position vertically on the screen. When the +
button is pressed, the OSD control menu will move to the top side
of the screen. Likewise, when the - button is pressed, the OSD
control menu will move to the lower side.
Press + or - to select C1/9300, C2/6500 and USER. Only when
selecting USER can you make adjustments to the R/G/B content.
Press Enter to restore to factory default setting.
Press Auto to enable this function. The Auto-Adjust will
automatically adjust V-Position, H-Position, Clock and
Clock-Phase. This adjustment takes about 5 seconds.
Returns the monitor to its default settings.
Select from English, French, Italian, German and Spanish.
Indicates the current resolution, H-Frequency and V-Frequency.
Preset Modes
To reduce the need for adjustment for different modes, the monitor has default
setting modes that are most commonly used as given in the table below. If any
of these display modes are detected, the monitor automatically adjusts the
picture size and centering. When none of the mode is matched, the user can
store their preferred modes in the user modes. The monitor is capable of storing
up to 7 user modes. The only condition to store as a user mode is the new
display information must have 1 KHz difference for horizontal frequency or 1
Hz for vertical frequency or the sync signal polarities are different from the
default modes.
Mode
Resolution
H. Freq.
(KHz)
Band Width
(MHz)
H
V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
VGA 720x350 70 Hz
VGA 720x400 70 Hz
VGA 640x480 60 Hz
MAC 640x480 66 Hz
VESA 640x480 72 Hz
VESA 640x480 75 Hz
VESA 800x600 56 Hz
VESA 800x600 60 Hz
VESA 800x600 75 Hz
VESA 800x600 72 Hz
MAC 832x624 75 Hz
VESA 1024x768 60 Hz
SUN 1024x768 65 Hz
VESA 1024x768 70 Hz
VESA 1024x768 75 Hz
31.47
31.47
31.47
35.00
37.86
37.50
35.16
37.88
46.88
48.08
49.72
48.36
52.45
56.48
60.02
28.322
28.322
25.175
32.24
31.5
31.5
36
40
49.5
50
57.283
65
70.49
75
78.75
+
+
+
+
+
+
+
+
+
+
3-19
Power Management System
The monitor is equipped with the power management function which
automatically reduce the power consumption when not in use into four power
saving modes.
Mode
Power LED
Color
Power
Consumption
Horizontal
Sync.
On
Standby
Suspend
Off
Green
Amber
Amber
Amber
<30W
<5W
<5W
<5W
On
Off
On
Off
Vertical
Sync.
On
On
Off
Off
Polarity
We recommend switching the monitor off when it is not in use for a long time.
NOTE:
The monitor automatically goes through the Power Management System (PMS) steps
when it is idle. To release the monitor from PMS condition, press any key on the
keyboard or move mouse.
Display Angle
For viewing clarity, you can tilt the LCD forward (up to 5 degrees) or backward
(up to 30 degrees.)
CAUTION
3-20
In order to protect the LCD, be sure to hold the base when adjusting the LCD, and take
care not to touch the screen.
User Guide
CHAPTER
4
TROUBLESHOOTING
CHAPTER4
If you are experiencing trouble with your touchmonitor, refer to the following
table. If the problem persists, please contact your local dealer or our service
center.
Solutions to Common Problems
Problem
Suggestion(s)
The monitor does not respond
after you turn on the system.
Check that the monitor’s Power Switch is on.
Turn off the power and check the monitor’s power cord and signal cable
for proper connection.
Characters on the screen are dim
Refer to the About Touchmonitor Adjustments section to adjust the
brightness.
The screen is blank
During operation, the monitor screen may automatically turn off as a
result of the Power Saving feature. Press any key to see if the screen
reappears.
Refer to the About Touchmonitor Adjustments section to adjust the
brightness.
Screen flashes when initialized
Turn the monitor off then turn it on again.
“Out of Range” display
check to see of the resolution of your computer is higher than that of the
LCD display.
Reconfigure the resolution of your computer to make it less than or equal
to 1024x768. See Appendix A for more information on resolution.
Touch doesn’t work
Make sure cable is securely attached at both ends.
4-21
4-22
User Guide
APPENDIX
A
NATIVE RESOLUTION
CHAPTER4
The native resolution of a monitor is the resolution level at which the LCD
panel is designed to perform best. For the LCD touchmonitor, the native
resolution is 800 x 600 for the 15 inch size. In almost all cases, screen images
look best when viewed at their native resolution. You can lower the resolution
setting of a monitor but not increase it.
Input Video
15" LCD
640x480 (VGA)
Transforms input format to 1024x768
800x600 (SVGA)
1024x768 (XGA)
Transforms input format to 1024x768
Displays in Native Resolution
The native resolution of an LCD is the actual number of pixels horizontally in
the LCD by the number of pixels vertically in the LCD. LCD resolution is
usually represented by the following symbols:
VGA
640x480
SVGA
800x600
XGA
1024x768
SXGA
1280x1024
UXGA
1600x1200
A-23
As an example, a SVGA resolution LCD panel has 800 pixels horizontally by
600 pixels vertically. Input video is also represented by the same terms. XGA
input video has a format of 1024 pixels horizontally by 768 pixels vertically.
When the input pixels contained in the video input format match the native
resolution of the panel, there is a one to one correspondence of mapping of input
video pixels to LCD pixels. As an example, the pixel in column 45 and row 26
of the input video is in column 45 and row 26 of the LCD. For the case when
the input video is at a lower resolution than the native resolution of the LCD, the
direct correspondence between the video pixels and the LCD pixels is lost. The
LCD controller can compute the correspondence between video pixels and LCD
pixels using algorithms contained on its controller. The accuracy of the
algorithms determines the fidelity of conversion of video pixels to LCD pixels.
Poor fidelity conversion can result in artifacts in the LCD displayed image such
as varying width characters.
A-24
User Guide
APPENDIX
B
TOUCHMONITOR SAFETY
CHAPTER4
This manual contains information that is important for the proper setup and
maintenance of your touchmonitor. Before setting up and powering on your new
touchmonitor, read through this manual, especially Chapter 2 (Installation), and
Chapter 3 (Operation).
1 To reduce the risk of electric shock, follow all safety notices and never open
the touchmonitor case.
2 Turn off the product before cleaning
3 Your new touchmonitor is equipped with a 3-wire, grounding power cord.
The power cord plug will only fit into a grounded outlet. Do not attempt to fit
the plug into an outlet that has not been configured for this purpose. Do not
use a damaged power cord. Use only the power cord that comes with your
touchmonitor. Use of an unauthorized power cord may invalidate your
warranty.
4 The slots located on the sides and top of the touchmonitor case are for
ventilation. Do not block or insert anything inside the ventilation slots.
5 It is important that your touchmonitor remains dry. Do not pour liquid into or
onto your touchmonitor. If your touchmonitor becomes wet do not attempt to
repair it yourself.
B-25
Care and Handling of Your Touchmonitor
The following tips will help keep your touchmonitor functioning at the optimal
level.
• To avoid risk of electric shock, do not disassemble the brick supply or
display unit cabinet. The unit is not user serviceable. Remember to unplug
the display unit from the power outlet before cleaning.
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do
not use thinner or benzene, abrasive cleaners or compressed air.
• To clean the display unit cabinet, use a cloth lightly dampened with a mild
detergent.
• Avoid getting liquids inside your touchmonitor. If liquid does get inside,
have a qualified service technician check it before you power it on again.
• Do not wipe the screen with a cloth or sponge that could scratch the surface.
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the
rag and wipe the touchscreen. Never apply the cleaner directly on the
touchscreen
B-26
User Guide
APPENDIX
C
TECHNICAL SPECIFICATIONS
CHAPTER4
C-27
Touchmonitor Specifications
Model
ET1524L
LCD Display
Display Size
Pixel Pitch
Display Mode
15” TFT Active Matrix Panel
304.(H) x 228.(V) mm
0.297(H) x 0.297(V) mm
VGA 640 x 350 (70Hz)
VGA 720 x 400 (70Hz)
VGA 640 x 480 (60 / 72/ 75Hz)
SVGA 800 x 600 (56 / 60 / 72/ 75Hz)
XGA 1024 x 768 (60 / 70 / 75Hz)
Max. Resolution
Contrast Ratio
Brightness
Response Time
Display Color
Viewing Angle
Input Signal
XGA (1024 x 768) at 75Hz maximum
350 : 1 (typical)
200 Cd/m2 wo/touch 150 Cd/m2 w/touch
Tr: 13 ms Tf: 27 ms (Typ.)
16.7M
Vertical -55o ~ +45o
Horizontal -60o ~+60o
Video
R.G.B. Analog 0.7Vp-p, 75 ohm
Sync
TTL Positive or Negative
Signal Connector
Front Control
OSD
Mini D-Sub 15 pin
Enter, Auto, -,+, Menu/Exit, Power
Contrast, Brightness, H-Position, V-Position, Color
Temperature, Phase, Clock, OSD Time, Recall, Language:
French, Italian, German, Spanish
DDC1 / 2B
Plug & Play
Touch Panel (optional)
Power Adapter
Operating Conditions
Storage Conditions
Dimensions (HxWxD)
Weight (Net)
Certifications
C-28
User Guide
AccuTouch
Input AC 100-240V, 50-60Hz
Temperature
0oC ~ 40oC (32oF ~ 104oF)
Humidity
20% ~ 80% (No Condensation)
Altitude
To 12,000 Feet
Temperature
-20oC ~ 60oC (-4oF ~ 140oF)
Humidity
10% ~ 90% (No Condensation)
370 x 381 x 194mm
5.4Kg
UL, C-UL, FCC-B, CE, TUV, VCCI, C-Tick, MPRII
AccuTouch Touchscreen Specifications
Mechanical
Construction
Positional Accuracy
Touchpoint Density
Touch Activation Force
Surface Durability
Expected Life
Performance
Top: Polyester with outside hard-surface coating with clear or
antiglare finish.
Inside: Transparent conductive coating.
Bottom: Glass substrate with uniform resistive coating. Top and
bottom layers separated by patented separator dots.
Standard deviation of error is less than 0.080 in. (2.03 mm). This
equates to less than ±1%.
More than 100,000 touchpoints/in² (15,500 touchpoints/cm²).
Typically less than 4 ounces (113 grams).
Meets Taber Abrasion Test (ASTM D1044), CS-10F wheel, 500 g.
Meets pencil hardness 3H.
AccuTouch technology has been operationally tested to greater than
35 million touches in one location without failure, using a stylus
similar to a finger.
Optical
Light Transmission
(per ASTM D1003)
Visual Resolution
Typically 85% at 550-nm wavelength (visible light spectrum).
Haze (per ASTM D1003)
Gloss (per ASTM D2457)
Antiglare surface: Less than 15%.
All measurements made using USAF 1951 Resolution Chart, under
30 X magnification, with test unit located approximately 1.5 in.
(38 mm) from surface of resolution chart.
Antiglare surface: 6:1 minimum.
Antiglare surface: 90 ± 20 gloss units tested on a hard-coated front
surface.
C-29
15" LCD Touchmonitor (ET1524L-XXWC-1) Dimensions
C-30
User Guide
REGULATORY INFORMATION
CHAPTER4
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified herein will likely result in improper operation,
damage to the equipment or pose a fire hazard if the limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety hazard. Service
should be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an integral
safety ground wire intended for connection to a grounded safety outlet.
1) Do not substitute the cord with other than the provided approved type.
Under no circumstances use an adapter plug to connect to a 2-wire outlet as
this will defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can
result in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are questions
about the installation prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B limits for
radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided
cords and cabling may compromise electrical safety or CE Mark Certification for
emissions or immunity as required by the following standards:
31
This Information Technology Equipment (ITE) is required to have a CE Mark
on the manufacturer’s label which means that the equipment has been tested
to the following Directives and Standards:
This equipment has been tested to the requirements for the CE Mark as
required by EMC Directive 89/336/EEC indicated in European Standard EN
55 022 Class B and the Low Voltage Directive 73/23/EEC as indicated in
European Standard EN 60 950.
D) General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the
equipment may cause interference with radio and television communications.
There is, however, no guarantee that interference will not occur in any particular
installation due to site-specific factors.
1) In order to meet emission and immunity requirements, the user must
observe the following:
a) Use only the provided I/O cables to connect this digital device with
any computer.
b) To ensure compliance, use only the provided manufacturer’s approved
line cord.
c) The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2) If this equipment appears to cause interference with radio or television
reception, or any other device:
a) Verify as an emission source by turning the equipment off and on.
b) If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected
receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device
does not use. (Unterminated I/O cables are a potential source of
high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle.
Do not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician.
32
User Guide
33
34
User Guide
WARRANTY
CHAPTER4
Except as otherwise stated herein or in an order acknowledgment delivered to
Buyer, Seller warrants to Buyer that the Product shall be free of defects in
materials and workmanship. The warranty for the touchmonitors and
components of the product are: 3 years monitor, 5 years Accu- Touch screen, 5
years Controller.
Seller makes no warranty regarding the model life of components. Seller’s
suppliers may at any time and from time to time make changes in the
components delivered as Products or components.
Buyer shall notify Seller in writing promptly (and in no case later than thirty
(30) days after discovery) of the failure of any Product to conform to the
warranty set forth above; shall describe in commercially reasonable detail in
such notice the symptoms associated with such failure; and shall provide to
Seller the opportunity to inspect such Products as installed, if possible. The
notice must be received by Seller during the Warranty Period for such product,
unless otherwise directed in writing by the Seller. Within thirty (30) days after
submitting such notice, Buyer shall package the allegedly defective Product in
its original shipping carton(s) or a functional equivalent and shall ship to Seller
at Buyer’s expense and risk.
Within a reasonable time after receipt of the allegedly defective Product and
verification by Seller that the Product fails to meet the warranty set forth above,
Seller shall correct such failure by, at Seller’s options, either (i) modifying or
repairing the Product or (ii) replacing the Product. Such modification, repair, or
replacement and the return shipment of the Product with minimum insurance to
Buyer shall be at Seller’s expense. Buyer shall bear the risk of loss or damage in
transit, and may insure the Product. Buyer shall reimburse Seller for
transportation cost incurred for Product returned but not found by Seller to be
defective. Modification or repair, of Products may, at Seller’s option, take place
either at Seller’s facilities or at Buyer’s premises. If Seller is unable to modify,
repair, or replace a Product to conform to the warranty set forth above, then
Seller shall, at Seller’s option, either refund to Buyer or credit to Buyer’s
account the purchase price of the Product less depreciation calculated on a
straight-line basis over Seller’s stated Warranty Period.
35
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES
FOR BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS
WARRANTY SET FORTH ABOVE, SELLER GRANTS NO OTHER
WARRANTIES, EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE,
REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE,
THEIR QUALITY, THEIR MERCHANTABILITY, THEIR
NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER
OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY
FOR THE GOODS OTHER THAN THE WARRANTY SET FORTH
HEREIN. SELLER’S LIABILITY UNDER THE WARRANTY SHALL BE
LIMITED TO A REFUND OF THE PURCHASE PRICE OF THE PRODUCT.
IN NO EVENT SHALL SELLER BE LIABLE FOR THE COST OF
PROCUREMENT OR INSTALLATION OF SUBSTITUTE GOODS BY
BUYER OR FOR ANY SPECIAL, CONSEQUENTIAL, INDIRECT, OR
INCIDENTAL DAMAGES.
Buyer assumes the risk and agrees to indemnify Seller against and hold Seller
harmless from all liability relating to (i) assessing the suitability for Buyer’s
intended use of the Products and of any system design or drawing and (ii)
determining the compliance of Buyer’s use of the Products with applicable
laws, regulations, codes, and standards. Buyer retains and accepts full
responsibility for all warranty and other claims relating to or arising from
Buyer’s products, which include or incorporate Products or components
manufactured or supplied by Seller. Buyer is solely responsible for any and all
representations and warranties regarding the Products made or authorized by
Buyer. Buyer will indemnify Seller and hold Seller harmless from any liability,
claims, loss, cost, or expenses (including reasonable attorney’s fees) attributable
to Buyer’s products or representations or warranties concerning same.
36
User Guide
INDEX
Numerics
About the Product, 8
About Touchmonitor Adjustments, 15
AccuTouch Touchmonitor Specifications, 29
Image, scrolling, 21
Input Signal, 28
Installation and Setup, 9
Installing the Driver Software, 12
Installing the Serial Touch Driver, 13
Installing the Serial Touch Driver for MS-DOS and
Windows 3.1, 14
Installing the Serial Touch Driver for Windows XP,
Windows 2000, Me, 95/98 and NT 4.0, 13
B
L
Brightness, 28
Light Transmission, AccuTouch, 29
C
M
Care and Handling of Your Touchmonitor, 26
Certifications, 28
Cleaning Your Touchmonitor, 26
Construction, AccuTouch, 29
Contrast Ratio, 28
Controls and Adjustment, 17
Main Unit, 10
Max. Resolution, 28
Mechanical, AccuTouch, 29
15" LCD Touchmonitor (ET1524L-XXWC-1)
Dimensions, 30
A
D
Dimensions (HxWxD), 28
Display Angle, 20
Display Color, 28
Display Mode, 28
Display Size, 28
E
Electrical Safety Information, 31
Emissions and Immunity Information, 31
Expected Life Performance, AccuTouch, 29
F
Front Control, 28
Front Panel Controls, 16
G
N
Native Resolution, 23
O
Operating Conditions, 28
Optical, AccuTouch, 29
OSD, 28
OSD Control Options, 18
OSD Menu Functions, 17
P
Pixel Pitch, 28
Plug & Play, 28
Positional Accuracy, AccuTouch, 29
Power Adapter, 28
Power Management System, 20
Precautions, 7
Product Description, 7
Product Overview, 10
Gloss, AccuTouch, 29
R
H
Rear View, 10
Regulatory Information, 31
Response Time, 28
Haze, AccuTouch, 29
I
Image problem, 21
S
Signal Connector, 28
Solutions to Common Problems, 21
Index-37
Storage Conditions, 28
Surface Durability, AccuTouch, 29
SVGA, 23
SXGA, 23
T
Technical Specifications, 27
Touch Activation Force, AccuTouch, 29
Touch Interface Connection, 11
Touch not working, 21
Touch Panel (optional), 28
Touchmonitor Safety, 25
Touchmonitor Specifications, 28
Touchpoint Density, AccuTouch, 29
Troubleshooting, 21
U
Unpacking Your Touchmonitor, 9
UXGA, 23
V
VGA, 23
Viewing Angle, 28
Visual Resolution, AccuTouch, 29
W
Warranty, 35
Weight (Net), 28
X
XGA, 23
Index-38
Download PDF

advertising