Installation manual | El Paso Chile Company DMS 3120-120 Stereo Amplifier User Manual

®
PROFESSIONAL AUDIO & SOUND
Manual
Series DMS
OM 163
Integrated Amplifiers
TM
Installation Manual
and Operating Instructions
DIGITAL MUSIC SERIES
DIGITAL MUSIC SERIES
7 Channel - 3 Zone - Dual VOX Dual Mute - MOH - Vox Relay Module Port - Phone Interface
DMS 3040 - 40 Watt RMS
DMS 3080 - 80 Watt RMS
DMS 3120 - 120 Watt RMS
IMPORTANT NOTE: THIS OPERATING MANUAL IS PROVIDED AS AN INSTALLATION AND
AS AN OPERATING AID. PASO SOUND PRODUCTS, INC. DOES NOT ASSUME ANY
RESPONSIBILITY AS TO ITS ACCURACY AND SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING
FROM THE INSTALLATION, USE OR INABILITY TO USE THIS PRODUCT.
CAUTION !
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK DO NOT EXPOSE THIS APPLIANCE TO
WATER, RAIN OR MOISTURE
Digital Music Amplifiers
TM
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
30TJ
Innovation through technology since 1931
© copyright Paso Sound Products, Inc. 2003
Specifications are subject to change without notice
REV. 1.5
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
DESCRIPTION AND APPLICATIONS
SPECIFICATIONS
Power Output:
DMS3040
DMS3080
DMS3120
Distortion:
Frequency Response:
Inputs:
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
Sensitivity & Z:
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
AUX 1 Input
Attenuator:
AUX 2 Input
Attenuator:
Phantom Power:
Hum & Noise:
Telephone Paging Input:
Accessory Port:
EQ LINK:
Line Outputs:
Inputs/Outputs:
Subwoofer Outputs:
Subwoofer Output Level:
Music on Hold Output:
Zone 2 Output:
Zone 3 Output:
Main Output Impedance:
Controls:
Front Panel:
❑ High Performance - High Reliability Design
❑ Wide Frequency Response - Very Low Distortion
❑ 7 Channel Inputs - 3 Zone Outputs
❑ 5 Balanced Microphone Inputs
❑ Phantom Power on all MIC Inputs
❑ MIC 4/AUX 1 and MIC 5/AUX 2 Inputs
With Stereo Summing
❑ AUX1 and AUX2 Inputs Attenuator
❑ 600 ohm Transformer Balanced
Telephone Paging Input
❑ MIX Buss and 600 ohm Line Output
❑ Independent Input Controls
❑ Rear Panel Port: Accepts Standard Module
❑ Independent Module Level Control
❑ AUX1 and Master Remote Volume Controls
❑ External EQ Link
❑ Tone by-pass and EQ Link switches
❑ Pre-EQ Subwoofer Output
❑ Post-EQ Subwoofer Output
❑ Addressable Dual VOX Buss
Voice Activated Muting
❑ VOX Variable Time Delay Function
❑ Addressable Dual MUTE Buss
❑ Direct Muting and Unmuting
❑ 600 ohm and 8 ohm 1 Watt
Music on Hold Amplifier
❑ MOH Amplifier Source Selector
❑ Zone 2 and 3, 1 Watt - 8 ohm Output
with Separate Control
❑ NO/NC VOX Operated Relay
❑ 24 V DC 250 mA Regulated Power Supply Output
❑ 8 ohm, 25 Volt & 70 Volt Output
❑ Optional 19” Rack Mounting with Kit
❑ Low profile - 2-Unit of Vertical Rack space
❑ UL 6500 Listed (US - CANADA)
Immediately upon receipt of the amplifier, inspect the unit
and shipping container for indications of improper handling
or in transit damage. The equipment was carefully inspected and tested before leaving the factory. Notify the
Transportation Company immediately if any damage is
found. ONLY THE CONSIGNEE CAN FILE A CLAIM WITH
THE CARRIER FOR DAMAGE DURING SHIPMENT. Be
sure to save the carton and packing material as evidence of
damage for the shipper inspection. DO NOT SHIP the unit
back to the factory unless authorized by the factory.
IN TRANSIT DAMAGES ARE NOT COVERED BY THE
PASO WARRANTY.
PAGE 2
© copyright Paso Sound Products, Inc. 2002
Microphone 1 Balanced
Microphone 2 Balanced
Microphone 3 Balanced
Microphone 4 Balanced - AUX 1 (Stereo Summing)
Microphone 5 Balanced - AUX 2 (Stereo Summing)
Telephone Interface - Transformer Balanced
Module Port
Mic 1 = 1.5 Mv - 250 ohm
Mic 2 = 1.5 Mv - 250 ohm
Mic 3 = 1.5 Mv - 250 ohm
Mic 4 = 1.5 Mv - 250 ohm - AUX 1 = 100 Mv - 47K
ohm
Mic 5 = 1.5 Mv - 250 ohm - AUX 2 = 100 Mv - 47K
ohm
Tel=100 Mv - 600 ohm - Transformer Balanced
Module= 1 V - 47K ohm
Variable (rear panel control)
Variable (rear panel control)
All Microphone Inputs by internal jumper (18 V)
Mic -70 db, Aux -75 db
600 ohm Transformer balanced
Accepts Standard Module
Preamp out, Power Amp in with EQ Link Switch
Line Out 600 ohm - 1.5 V loaded
MIX BUSS
Pre-EQ and Post-EQ Outputs
1 Volt
600 ohm-1 Volt Transformer Balanced
1 Watt-8 ohm with Control
1 Watt-8 ohm with Control
8 ohm, 25 Volt and 70 Volt line
AC Accessory Outlet:
Terminations:
Housing Finish:
Output Power Indicator:
Dimensions:
Net Weight:
Input 1 Level, Input 2 Level, Input 3 Level, Input 4
Level, Input 5 Level, Module Level, Bass and Treble
PHONE Level - AUX 1 Attenuator - AUX 2 Attenuator
- MOH/ZONE 1 Level Control - ZONE 2 Level Control
- VOX 1/VOX 2 Sensitivity - MUTE 2 Delay
± 10 dB at 100 Hz and 10 KHz
On - Off Switch (rear panel)
AUX 1 Input Level and Master Volume (10 K)
AUX 1 - AUX 2 - MODULE by internal jumper
AUX 1 - AUX 2 - MODULE by internal jumper
Voice Activated Muting
Available on all 7 Inputs by internal jumpers
Available on all 7 Inputs by internal jumpers
Available on all 7 Inputs by internal jumpers
Available on all 7 Inputs by internal jumpers
Adjustable from 3 Sec to 30 Sec (rear panel control)
MUTES/UNMUTES MIC 1 only
24 V DC - 250 mA Regulated
NO/NC Contacts - VOX activated - Contacts Rating =
30 VDC - 7 A
Optional Model 27/3501 - 19” Rack Kit
3” Thermally Controlled - Model DMS3120 only
117 Volt, 50-60 Hz
DMS3040 = AC = 630 VA - DMS3080 = 750 VA DMS3120 = 850VA Max.
500 W Max. Unswitched
Screw Terminals, RCA Jacks
Black
Multi-color LED (front panel)
19” W., 12” D., 4” H. with feet (482X305X102 mm) 3.5”
H (89 mm). less feet
DMS3040
DMS3080
DMS3120
16 Lbs (8 Kg)
19 Lbs (8.5 Kg)
22 Lbs (11 Kg)
Rear Panel:
UNPACKING
40 Watt RMS
80 Watt RMS
120 Watt RMS
Less than 0.5% THD
20 - 20,000 Hz ± 1 db
Bass and Treble Controls:
Tone By-Pass:
Remote Volume Controls:
MOH Source Selection:
Zone 2/3 Source Selection:
DUAL VOX:
VOX BUSS 1:
VOX BUSS 2:
MUTE BUSS 1:
MUTE BUSS 2:
MUTE 2 DELAY:
Unmuting:
Power Supply Output:
Auto VOX Relay:
Rack Mounting:
Internal Cooling Fan:
Power Requirement:
Power Consumption:
Specifications are subject to change without notice
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE OPERATING
READ BEFORE OPERATING
BEFORE OPERATING THE AMPLIFIER, BE SURE YOU
FULLY UNDERSTAND ALL INSTRUCTIONS AND FEATURES OF THE UNIT.
outlet, consult an electrician for replacement of the
obsolete outlet.
12) Use only the attachments and accessories specified in this manual.
13) If a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tipover.
14) Unplug this apparatus during lighting storms or
when unused for long periods of time.
15) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
16) DO NOT replace fuses unless power cord is
removed from the AC wall outlet.
17) DO NOT install accessories unless the power
cord is removed from the AC wall outlet.
1) Read these instructions carefully.
2) Keep these instructions.
3) Heed all Warnings.
4) Follow all instructions.
5) DO NOT use this apparatus near water.
6) Clean ONLY with a damp cloth.
7) DO NOT block any of the ventilation openings.
Install in accordance with the instructions provided.
8) DO NOT install near any heat sources such as
radiators, stoves, or other apparatus (including amplifiers) that produce heat.
9) DO NOT mount amplifier into a container or a
closed unventilated closet while operating.
10) DO NOT place any object or accessory equipment
such as Tuners, Mixers, Cassette Decks, etc. on top of
the amplifier. Obstructing or closing the cabinet ventilation openings may cause overheating.
11) DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The
wide blade and or the third prong is provided for your
safety. When the provided plug does not fit into your
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS APPLIANCE TO WATER, RAIN OR
MOISTURE
RACK MOUNTING
A) Procure the optional accessory Rack Mount Kit Model 27/3501.
B) Turn amplifier up side down and remove the four rubber feet by unscrewing the four holding screws.
C) Remove two screws on each side of the amplifier holding the amplifier cover.
D) Install the rack kit brackets by using the self-tapping screws provided.
Fig. 3 - Rack Kit Mounting
OUTPUT LEVEL
DMS
TM
DIGITAL MUSIC AMPLIFIER
PEAK
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
POWER
0
10
INPUT 1
DMS3040/3080/3120
0
10
INPUT 2
0
10
INPUT 3
0
10
INPUT 4/AUX 1
0
10
INPUT 5/AUX 2
0
10
MODULE
-10
+10
BASS
-10
+10
O
TREBLE
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 3
PAGE 4
0
1
INPUT 1
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
10
INPUT 3 Volume Control
INPUT 4/AUX 1 Volume Control
INPUT 5/AUX 2 Volume Control
4)
5)
4
INPUT 4/AUX 1
0
3)
3
INPUT 3
10
INPUT 2 Volume Control
0
2)
2
INPUT 2
10
INPUT 1 Volume Control
0
6
10
5
0
MODULE
10
INPUT 5/AUX 2
0
DIGITAL MUSIC AMPLIFIER
1)
10
DIGITAL MUSIC SERIES
TM
DMS
8
TREBLE
+10
On-Off Power Switch
TREBLE Control
BASS Control
10) Output Level Meter
9)
-10
Input Module Level Control
7
BASS
+10
PROFESSIONAL AUDIO & SOUND
9
O
POWER
OUTPUT LEVEL
10
PEAK
DIGITAL MUSIC AMPLIFIERS
8)
7)
6)
-10
Fig. 4 - FRONT PANEL CONTROLS
®
TM
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC SERIES
DMS3040/3080/3120
2
3
0
37
117V 60HZ
36
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
LINE FUSE
5A 250V
117V 500W MAX
UNSWITCHED
MOH OUT 1 WATT
8
8
1 WATT
0
ZONE 2
ZONE 2
LEVEL
34
DMS3120 Rear Panel
Manual
SPEAKER OUTPUT
CLASS 2 WIRING ACCEPTABLE
VOX-1
SENS
33
32
VOX-2
SENS
-
31
GROUND
G
10
CAUTION
MASTER
REMOTE
VOLUME
M1 RVC RVC C
11
RISK OF ELECTRIC SHOCK
DO NOT OPEN
M2
MUTE 2
30
OUT
SUB OUT
PRE EQ
G
MIX
BUSS
16
27
26
G COM HOT
25
19
24
20
21
23
TEL OUTPUT
LEVEL
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
R
(AUX2)
ATTENUATOR
L
INPUT-5(AUX2)
47kohm 100mV
600 ohm 100mV
G COM HOT
TEL
INPUT-4(AUX1)
47kohm 100mV
(AUX1)
ATTENUATOR
17
18
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
COM HOT RVC RVC
INPUT 4 (MIC)
250ohm 1.5mV
BALANCED
G COM HOT
28
PRE
OUT
14
15
OFF
ON
POWER SUB OUT LINE OUT TONE
POST EQ
IN
600
BYPASS
INPUT 3 (MIC)
EQ LINK
IN
EQ LINK
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
US 30TJ
12
13
INPUT 5/AUX 2 - Stereo Summing Jacks
AUX 2 Input Attenuator
Standard Module Port
TELEPHONE Paging Output Level Control
TELEPHONE Paging Balanced Input 600 Ohm
INPUT 5/AUX 2 - Balanced Input
INPUT 4/AUX 1 - Remote Volume Control Terminals
INPUT 4 - Balanced MIC Input
INPUT 3 - Balanced MIC Input
INPUT 2 - Balanced MIC Input
INPUT 1 - Balanced MIC Input
MUTE 2 Time Delay Control
VOX 2 Sensitivity Control
VOX 1 Sensitivity Control
Speaker Output Terminals
Chassis Ground
AC LIne Fuse
AC Power Cord
29
G COM HOT
INPUT 2 (MIC)
20)
21)
22)
23)
24)
25)
26)
27)
28)
29)
30)
31)
32)
33)
34)
35)
36)
37)
G COM HOT
INPUT 1 (MIC)
WARNING: THIS APPLIANCE
MUST BE EARTHED
MIC1
120 W RMS
117V 60 HZ
850 VA
MUTE-2
DELAY
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
SER. NO.
+
9
DMS3120
NO
24V DC
250 mA
8
DIGITAL MUSIC AMPLIFIER
PROFESSIONAL AUDIO & SOUND
C
VOX RELAY
NC
Unswitched AC Auxiliary Socket
ZONE 1 - Output Level Control
Zone 1 MOH - 600 ohm, 1 Volt Output
Zone 1 - 8 ohm, 1 Watt Output
Zone 2 - 8 ohm, 1 Watt Output
ZONE 2 - Output Level Control
VOX Relay NO/NC Contact Terminals
24 Volt DC Regulated Power Supply Output
MIC 1 UNMUTE
MUTE 1 - MUTE 2 Terminals
Master Remote Volume Control Terminals
EQ LINK - IN - OUT Switch
EQ LINK - PREAMP. OUT/POWER AMP IN
SUB OUT - PRE EQ and POST EQ
MIX BUSS
LINE OUT 600 Ohm
TONE BYPASS - ON/OFF SWITCH
AUX 1 Input Attenuator
INPUT 4/AUX 1 - Stereo Summing Jacks
35
GROUND
BALANCED
ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE
CAUTION: TO REDUCE THE RISK OF FIRE OR OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE
SHOCK DO NOT EXPOSE THIS APPLIANCE TO OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN
RAIN OR MOISTURE. DO NOT REMOVE COVER. REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER
THERE ARE NO USER SERVICEABLE PARTS UNE PERSONNE QUALIFIEE
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
COM 8
25V 70V
LEVEL
4
6
7
UNMUTE
DMS3040/3080/3120
CAUTION: TO REDUCE THE ATTENTION: AFIN DE REDUIRE LE RISQUE
D'INCENDIE REMPLACER SEUL PAR UN
RISK OF FIRE, REPLACE
ZONE 1
FUSIBLE DE MEME TYPE.
ONLY WITH SAME TYPE
FUSE.
ZONE 1
0
600
1
5
MUTE 1
Fig. 5- REAR PANEL INPUTS - OUTPUTS - CONTROLS
CAUTION: REMOVE
POWER CORD FROM
AC OUTLET PRIOR TO
INSTALLING MODULE
PORT ACCEPTS
STANDARD
MODULE
22
®
DIGITAL MUSIC AMPLIFIERS
TM
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC SERIES
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 5
DMS3120 - 1
MAIN BOARD
AUX2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
SW222
M1 M2 OFF
(MODULE)
M2 M1 OFF
AUX1
HOT
SW223
M1 M2 OFF
M2 M1 OFF
SW214
V1 V2 OFF
TEL PAGING
VOX1 VOX2
JUMPER
SW221
V1 V2 OFF
MODULE
VOX1 VOX2
JUMPER
GND
ON OFF
INPUT5 AUX2
VOX1 VOX2
JUMPER
SW213
V1 V2 OFF
INPUT4 AUX1
VOX1 VOX2
JUMPER
T204
M2 M1 OFF
SW219
INPUT2
ON OFF
HOT
M2 M1 OFF
SW220
INPUT1
COM
INPUT2
VOX1 VOX2
JUMPER
INPUT3
VOX1 VOX2
JUMPER
HOT
INPUT1
VOX1 VOX2
JUMPER
SW201
ON OFF
ON OFF
M2
M1
ZONE 1
SW701
AUX2 AUX1 MOD
ZONE 1
SW702
ZONE 1
AUX2 AUX1 MODULE
JUMPER
REV - 0
DMS3120 - 7
M. O. H. BOARD
CN 213
OPTIONAL
CHIME CARD
SOCKET
DMS3120 - 7
M.O.H. BOARD
REAR PANEL
SW702
AUX2 AUX1 MOD
ZONE 2
AUX2 AUX1 MODULE
JUMPER
M1
SW227
M2
AUX2 AUX1 MOD
ON OFF
SW205
SW206
(VOX RELAY) (UNMUTE) (CHIME TRIGER)
SW227
M2 M1
CHIME TRIGGER
SW205
ON OFF
MIC1 UNMUTE
SW206
M2 M1
VOX RELAY
SW701
AUX2 AUX1 MOD
GND
SW201 (MIC1)
COM
INPUT 1
(MIC)
SW215
INPUT1
V2 V1 OFF
GND
SW215
V1 V2 OFF
INPUT1
MUTE1 MUTE2
JUMPER
SW220
M1 M2 OFF
SW210
INPUT2
V2 V1 OFF
ON OFF
SW210
V1 V2 OFF
INPUT2
MUTE1 MUTE2
JUMPER
SW219
M1 M2 OFF
IT - 5000
SW211
INPUT3
GND
SW202
ON OFF
INPUT 2
(MIC)
SW203 (MIC3) SW202 (MIC2)
COM
SW211
V1 V2 OFF
INPUT3
MUTE1 MUTE2
JUMPER
SW212
V1 V2 OFF
INPUT4 AUX1
MUTE1 MUTE2
JUMPER
M2 M1 OFF
SW218
M1 M2 OFF
(INPUT4/AUX1)
M2 M1 OFF V2 V1 OFF
SW217
M1 M2 OFF
SW213
SW203
ON OFF
INPUT 3
(MIC)
HOT
V2 V1 OFF
GND
SW218
INPUT3
COM
INPUT 4
(MIC)
HOT
SW204 (MIC4)
RVC
SW228
(INPUT4)
AUX1 MIC4
RVC
(INPUT4/AUX1)
V2 V1 OFF
SW223
INPUT5/AUX2
AUX2 MIC5
(INPUT5)
INPUT5 AUX2
TEL PAGING
MUTE1 MUTE2 MUTE1 MUTE2
JUMPER
JUMPER
SW216
M1 M2 OFF
SW214
(TEL)
M2 M1 OFF
V2 V1 OFF
ON OFF
SW207
(MIC5)
COM
AUX 2
INPUT 5
SW229
AUX2 MIC
SW208
(INPUT5)
GND
SW216
(TEL)
COM
(MODULE)
V2 V1 OFF
HOT
TEL
INPUT 4
REMOTE
VOLUME
SW204
ON OFF
SW207
ON OFF
SW229
AUX2 MIC5
SW208
AUX2 MIC5
PHANTOM
POWER
MIC 3
PHANTOM
POWER
MIC 1
DIGITAL MUSIC AMPLIFIERS
MODULE
MUTE1 MUTE2
JUMPER
SW209
(MODULE IN)
SW209
AUX1 AUX2
MODULE
INPUT
SOURCE SWITCH
PHANTOM
POWER
MIC 4
PHANTOM
POWER
MIC 5
SW221
PHANTOM
POWER
MIC 2
AMPLIFIER REAR PANEL
INPUT5
AUX2 MIC5
SWITCH
(INPUT5/AUX2)
SW222
INPUT5
AUX2 MIC5
SWITCH
SW228
AUX1 MIC4
INPUT 4
AUX1 MIC4
SWITCH
Fig. 6 - MAIN PCB AND MOH BOARD TOP VIEW
SW217
PAGE 6
SW212
®
TM
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC SERIES
FUNCTION SWITCHES AND JUMPERS LOCATION
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
CAUTION !
REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD
ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET
THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE
PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY.
TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SERVICING UNLESS YOU
ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.
FUNCTION SWITCHES AND JUMPERS DEFAULT SETTING TABLE
JUMPER AND
SWITCH ID NO.
JUMPER
REFERENCE
FUNCTION
DESCRIPTION
FACTORY
SETTING
FACTORY
SETTING
MAIN PCB JUMPERS
SW201
SW202
SW203
SW204
SW205
SW206
SW207
SW210
SW211
SW212
SW213
SW214
SW215
SW216
SW217
SW218
SW219
SW220
SW221
SW222
SW223
SW227
INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 1 (MIC 1) VOX RELAY INPUT 5 INPUT 2 INPUT 3 INPUT 4 INPUT 5 TEL IN INPUT 1 TEL IN INPUT 4/AUX 1 INPUT 3 INPUT 2 INPUT 1 MODULE MODULE INPUT 5/AUX 2 CHIME TRIGGER -
PHANTOM POWER ON PHANTOM POWER ON PHANTOM POWER ON PHANTOM POWER ON UNMUTE ON - OFF
MUTE 1 - MUTE 2
PHANTOM POWER ON VOX 1 - VOX 2 - OFF
VOX 1 - VOX 2 - OFF
VOX 1 - VOX 2 - OFF
VOX 1 - VOX 2 - OFF
VOX 1 - VOX 2 - OFF
VOX 1 - VOX 2 - OFF
MUTE 1 - MUTE 2 - OFF
MUTE 1 - MUTE 2 - OFF
MUTE 1 - MUTE 2 - OFF
MUTE 1 - MUTE 2 - OFF
MUTE 1 - MUTE 2 - OFF
VOX 1 - VOX 2 - OFF
MUTE 1 - MUTE 2 - OFF
MUTE 1 - MUTE 2 - OFF
MUTE 1 - MUTE 2
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
M1
V1
V1
OFF
M1
OFF
OFF
OFF
OFF
OFF
M1
M1
SWITCHES
SW208
SW209
SW228
SW229
INPUT 5 MIC 5 OR AUX 2
MODULE IN SOURCE - AUX 1 OR AUX 2
INPUT 4 MIC 4 OR AUX 1
INPUT 5 MIC 5 OR AUX 2
SWITCH
SWITCH
SWITCH
SWITCH
AUX
AUX
AUX
AUX
2
1
1
2
MOH BOARD JUMPERS
SW701
SW702
ZONE 2 INPUT SOURCE ZONE 1 INPUT SOURCE -
AUX 1 - AUX 2 - MODULE
AUX 1 - AUX 2 - MODULE
AUX 1
AUX 1
REAR PANEL SWITCHES
SW301
SW302
DMS3040/3080/3120
TONE BYPASS
EQ LINK
Defeats Front Panel Bass & Treble
Inserts External EQ between
Preamp out and Power Amp Input
SWITCH OFF
SWITCH OUT
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 7
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
FUNCTION SWITCHES AND JUMPERS
UNDERSTANDING THE INPUT FUNCTIONS
SETTING THE VOX AND MUTE JUMPERS
DUAL VOX AND DUAL MUTE - The Amplifier provides two independent VOX (V1 & V2) and two MUTE (M1 & M2) SYSTEMS
JUMPER SETTINGS - The VOX and MUTE Functions are
SWITCHED-ON or OFF by setting the JUMPERS on the VOX (A)
and MUTE (B) SOCKET. See Fig. 8A.
FUNCTION SOCKETS - EACH INPUT IS PROVIDED WITH A
VOX (V1 & V2) AND A MUTE (M1 & M2) SOCKET.
INPUTS VOX AND MUTE FUNCTION - All Inputs including the
Module provide 2 - VOX SEND and 2 MUTE RECEIVE functions.
The VOX and MUTE functions are SWITCHED-ON, on each Input,
by Internal Jumpers provided for each Input. Two VOX BUSS
SEND (V1 & V2) and two MUTE BUSS RECEIVE (M1 & M2) can
be independently or simultaneously SWITCHED-ON to suit the
application requirement.
V1
TO VOX BUSS 1
VOX SEND
TO VOX BUSS 2
V2
SOURCE IN
The SOCKETS are located on the Main PCB inside the Amplifier
as shown on the SWITCHES and JUMPERS LOCATION DIAGRAM in this Manual. Each Socket is identified by an ID NUMBER
and the FUNCTION and DEFAULT settings are listed on the
FUNCTION SWITCHES and JUMPERS DEFAULT SETTING
TABLE in this Manual.
TO SET: Lift the Jumper and reset as required. making sure that
the JUMPER is properly positioned over the two shorting pins.
The VOX JUMPER has three positions:
The MUTE JUMPER has three positions:
VOX JUMPERS
SOCKET
MUTE JUMPERS
SOCKET
SW215
SW220
SOCKET
ID NO.
AUDIO OUT
ANY
INPUT
OFF
FROM MUTE BUSS 1
MUTE RECEIVE
DMS Anyinput
FROM MUTE BUSS 2
M2
Fig. 8 - Any Input VOX and MUTE Functions
The figure below shows how the VOX 1 Logic Switch and the
MUTE 2 Logic Switch are SWITCHED-ON by moving the Jumpers
from the OFF position to the V 1 and M 2 position. When the Input
is activated by a Source signal the corresponding VOX Signal is
sent to the V1 BUSS. When the VOX 2 is activated by another Input
the MUTE Signal is present on the MUTE 2 BUSS and it will
MUTE this Input
OFF
JUMPER
V1
M1
V2
M2
Vox Mute Socket
M1
OFF, V1 and V2
OFF, M1 and M2
A
JUMPER
JUMPER
B
Fig. 8A - VOX and MUTE Sockets
SETTING MORE THAN ONE FUNCTION
More than one JUMPER may be used on a VOX SOCKET as
shown below. In this example both the VOX 1 and VOX 2 functions
are SWITCHED -ON when the Input is activated. For this purpose
additional JUMPERS are packed with each Amplifier.
OFF
VOX 1 BUSS ON
V1
JUMPER
V2
JUMPER
VOX SOCKET
OFF
V1
VOX 2 BUSS ON
Vox Socket 01
JUMPER
VOX SEND
X
V2
SOURCE IN
ANY
INPUT
SW215 VOX 2 BUSS OFF
AUDIO OUT
A
VOX 2 BUSS ON
More than one JUMPER may be used on a MUTE SOCKET as
shown below. In this example both the MUTE 1 and MUTE 2 functions will MUTE this INPUT when either VOX 1 or VOX 2 are activated by other INPUTS.
JUMPER
OFF
M1
MUTE 1 BUSS ON
JUMPER
MUTE SOCKET
M2
SW220
Mute Socket 01
OFF
M1
MUTE 1 BUSS OFF
X
MUTE RECEIVE
JUMPER
DMS Anyinput 02
M2
MUTE 2 BUSS ON
Fig. 8B - Any Input VOX 1 and MUTE 2 Activated
PAGE 8
JUMPER
B
MUTE 2 BUSS ON
NOTE: BE SURE NOT TO SET BOTH THE VOX AND CORRESPONDING MUTE ON THE SAME INPUT OR THE INPUT WILL
MUTE ITSELF WHEN ACTIVATED.
EXAMPLE: INPUT 1 - V 1 and M 1 BOTH ON.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
FUNCTION SETTINGS EXAMPLES
EXAMPLE 9
EXAMPLE 9A
VOX - MUTE JUMPERS SETTING
VOX SEND
X
V2
SW215 VOX 2 BUSS OFF
JUMPER
OFF
M2
VOX SEND
JUMPER
MUTE 1 BUSS OFF
X
X
MUTE 2 BUSS OFF
MUTE RECEIVE
JUMPER
V2
MUSIC
IN
SW212 VOX 2 BUSS OFF
WHEN
MIC1
IS
ACTIVATED THE VOX 1
BUSS AND THE VOX 2
BUSS ARE SWITCHEDON AND THE SIGNALS
PRESENT ON THE
MUTE 1 & 2 BUSS WILL
MUTE THE TEL INPUT
AND INPUT 4/AUX 1
SW220
OFF
M1
JUMPER
M2
MUTE 2 BUSS OFF
VOX 1 BUSS ON
OFF
X
V2
PHONE OUT
TEL INPUT
WHEN
THE
TEL
INPUT IS ACTIVATED
THE VOX 1 BUSS IS
SWITCHED-ON AND
THE
SIGNAL
PRESENT ON THE
MUTE 1 BUSS WILL
MUTE INPUT 4/AUX 1
VOX 1 BUSS ON
OFF
SW216
OFF
M1
MUTE 1 BUSS OFF
X
JUMPER
M2
MUTE 2 BUSS ON
MUTE RECEIVE
X
SW215 VOX 2 BUSS OFF
MIC OUT
INPUT 1
V1
M2
JUMPER
MUSIC
IN
MUTE 1 BUSS OFF
MUTE 2 BUSS OFF
VOX 1 BUSS OFF
X
JUMPER
V2
JUKEBOX OUT
INPUT 4
AUX 1
WHEN INPUT 4AUX 1 IS
ACTIVATED THE VOX 2
BUSS IS SWITCHED-ON
AND THE SIGNAL PRESENT
ON THE MUTE 2 BUSS WILL
MUTE THE MUSIC FROM
INPUT 5/AUX 2
MUTE-2
DELAY
3 to 30 Sec
OFF
M1
MUSIC OUT
SW217
OFF
M1
Input 1-4 -Tel - 01
MUTE RECEIVE
M2
MUTE 1 BUSS ON
JUMPER
X
MUTE 2 BUSS OFF
EXAMPLES
X
M2
OFF
X
X
SW213
VOX 2 BUSS OFF
MUSIC OUT
SW223
M1
OFF
MUTE 1 BUSS ON
JUMPER
JUMPER
M2
MUTE 2 BUSS ON
MUTE 2 BUSS
INPUT 5/AUX 2 IS
MUTED BY BOTH INPUT
4/AUX 1 AND INPUT 1
WHEN ACTIVATED.
MUTE 1 BUSS
MUTE 2 BUSS OFF
Input 1-4 -5 - 03
EXAMPLE 9A - INPUT 1 (MIC 1) and TEL IN (Phone Paging) both
mute INPUT 4/AUX 1. When the Microphone or the Phone Paging
are activated the Music on AUX 1 is muted. The Microphone has priority over the Phone Paging. When MIC 1 is activated both the Phone
Paging and the Music on AUX 1 are muted.
VOX 1 BUSS OFF
JUMPER
V2
INPUT 5
AUX 2
EXAMPLE 9 - INPUT 1 (MIC 1) mutes INPUT 4/AUX 1. When the
Microphone is activated the Music on AUX 1 is muted.
MUTE 1 BUSS ON
X JUMPER
31
DMS3040/3080/3120
WHEN MIC1 OR TEL ARE
ACTIVATED THE VOX 1
BUSS IS SWITCHED-ON
AND THE SIGNAL PRESENT
ON THE MUTE 1 BUSS WILL
MUTE THE MUSIC FROM
INPUT 4/AUX 1
SW212 VOX 2 BUSS OFF
SW217
V1
MUSIC
IN
VOX 2 BUSS
JUKEBOX
IN
SW212 VOX 2 BUSS ON
INPUT 4
AUX 1
VOX 1 BUSS OFF
X
X
V2
X
X
OFF
V1
JUMPER
VOX SEND
SW220
OFF
M1
OFF
MUTE 2 BUSS
WHEN
MIC
1
IS
ACTIVATED THE VOX 1
BUSS AND THE VOX 2
BUSS ARE SWITCHEDON AND THE SIGNALS
PRESENT ON THE MUTE
1 & 2 BUSS WILL MUTE
THE INPUT 4/AUX 1 AND
INPUT 5/AUX 2
VOX 1 BUSS
JUMPER
MUTE 1 BUSS
JUMPER
MIC IN
VOX 2 BUSS
TEL IN
SW214 VOX 2 BUSS OFF
MUTE 2 BUSS OFF
VOX - MUTE JUMPERS SETTING
V2
MUTE 1 BUSS OFF
X
X
JUMPER
EXAMPLE 9B
V1
MIC OUT
INPUT 1
V1
MUTE 2 BUSS
MUTE 1 BUSS ON
JUMPER
X
M2
Input 1-4 - V1 - 01
MIC IN
VOX SEND
SW217
OFF
M1
SW215 VOX 2 BUSS ON
MUTE RECEIVE
MUSIC OUT
INPUT 4
AUX 1
WHEN MIC 1 IS ACTIVATED
THE VOX
1
BUSS
IS
SWITCHED-ON AND THE
SIGNAL PRESENT ON THE
MUTE 1 BUSS WILL MUTE THE
MUSIC FROM INPUT 4/AUX 1
MUTE RECEIVE
VOX 1 BUSS OFF
X
X
VOX SEND
MUTE 1 BUSS
OFF
V1
JUMPER
V2
VOX 2 BUSS
SW220
M1
JUMPER
JUMPER
INPUT 1
WHEN
MIC
1
IS
ACTIVATED THE VOX 1
BUSS IS SWITCHED-ON
AND
THE
SIGNAL
PRESENT
ON
THE
MUTE 1 BUSS WILL
MUTE INPUT 4/AUX 1
VOX 1 BUSS ON
OFF
V1
VOX 1 BUSS
MIC OUT
VOX 1 BUSS
JUMPER
MIC IN
VOX - MUTE JUMPERS SETTING
VOX 1 BUSS ON
OFF
V1
EXAMPLE 9B - INPUT 1 (MIC 1) mutes INPUT 4/AUX 1 and INPUT
5/AUX 2. INPUT 4 (Jukebox) mutes INPUT 5 (Sat. Rcvr). When the
Jukebox is turned-On the Background Music on AUX 2 is muted.
MUTE 2 DELAY (Reference 31) Control is provided. The Microphone
Paging has priority over the Background Music and the Jukebox.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 9
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER
ALL INPUT CONNECTIONS MUST BE MADE WITH THE AMPLIFIER POWER OFF.
INPUT 1 SETTING AS A MICROPHONE INPUT
MICROPHONE TYPE
The Microphone Input accepts Low Impedance (250-600 ohm)
Dynamic Microphones. The Microphone may be a balanced output
type (three wire) or an unbalanced output type (two wire).
PASO MICROPHONES
All PASO low impedance Microphones have a balanced output for
best performance. Connect the RED lead to terminal HOT, the
WHITE lead to terminal COM and the SHIELD to terminal G.
WIRING
THREE LEADS BALANCED MICROPHONE WIRING
INPUT 1 - Default Jumper Settings
The Diagram at Left shows the
Default Settings for INPUT 1.
VOX 1 is SWITCHED ON
VOX 2 is SWITCHED OFF
MUTE 1 is SWITCHED OFF
MUTE 2 is SWITCHED OFF
VOX - MUTE JUMPERS SETTING
SW215
VOX 1 BUSS
ACTIVATED
OFF
V1
JUMPER
VOX SEND
X
V2
VOX 2 BUSS OFF
= JUMPER
JUMPER
MIC IN
When the INPUT 1 (MIC 1) is
activated the VOX 1 BUSS is ON
and it will MUTE any Input with the
MUTE 1 Setting SWITCHED ON.
AUDIO OUT
INPUT 1
Input 1 - V1 - 01
250ohm 1.5mV
BALANCED
SW220
OFF
M1
MUTE RECEIVE
M2
JUMPER
MUTE 1 BUSS OFF
X
X
INPUT 1 (MIC)
INPUT 2 (MIC)
INPUT 3 (MIC)
G COM HOT
G COM HOT
G COM HOT
MUTE 2 BUSS OFF
The microphone leads color refers to Paso Microphones only.
When using other brand refer to instructions packed with that
unit.
SHIELD
NOTE: To change the
INPUT Default Settings
refer to the appropriate
section in this Manual
TWO LEADS UNBALANCED MICROPHONE WIRING
CABLE
RED
SW215
VOX 1 BUSS
ACTIVATED
OFF
V1
JUMPER
VOX SEND
X
V2
VOX 2 BUSS OFF
JUMPER
MIC IN
3120 Micbal 01
INPUT 1 - Default Jumper Settings
The Diagram at Left shows the
Default Settings for INPUT 1.
VOX 1 is SWITCHED ON
VOX 2 is SWITCHED OFF
MUTE 1 is SWITCHED OFF
MUTE 2 is SWITCHED OFF
When the INPUT 1 (MIC 1) is
activated the VOX 1 BUSS is ON
and it will MUTE any Input with the
MUTE 1 Setting SWITCHED ON.
= JUMPER
AUDIO OUT
INPUT 1
250ohm 1.5mV
BALANCED
Input 1 - V1 - 01
SW220
M1
M2
OFF
JUMPER
MUTE 1 BUSS OFF
INPUT 1 (MIC)
INPUT 2 (MIC)
INPUT 3 (MIC)
G COM HOT
G COM HOT
G COM HOT
X
X
MUTE 2 BUSS OFF
SHIELD
HOT LEAD
NOTE: To change the
INPUT Default Settings
refer to the appropriate
section in this Manual
3120 Micunbal 01
Fig. 10A - Unbalanced Microphone Input 1 Wiring
PAGE 10
BALANCED MICROPHONE
IMPORTANT NOTE: The use of an
unbalanced Microphone (two leads) is
not recommended. For best results in a
PA
Application
always
use
a
Unidirectional
Dynamic,
Low
Impedance, Balanced Microphone
(three leads).
Fig. 10 - Balanced Microphone Input 1 Wiring
WHITE
VOX - MUTE JUMPERS SETTING
MIC
Lo Z
DO NOT GROUND THE MICROPHONE
CABLE SHIELD TO THE CHASSIS OF
THE AMPLIFIER
UNBALANCED MICROPHONE
Attach the Microphone leads to the terminal strip as per diagram in Fig 8A. The
cable length should not exceed: 15 Ft.
(4.5 m).
MIC
Lo Z
MUTE RECEIVE
MICROPHONE INPUT
Attach the microphone leads to the terminal strip as per diagrams at left.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
CABLE LENGTH - If the distance
between the Microphone and the
Amplifier Input is greater than 15 ft (4.5
m) a Balanced Microphone must be
used. Use a two conductor shielded wire
and connect Microphone to Amplifier as
per Diagram in Fig. 10.
MICROPHONE CABLE ROUTING - The
Microphone Cable should be carefully
routed. Improper Cable routing will
cause spurious oscillations, regenerative
noises, hum, etc. that may permanently
damage the Amplifier.
z Do not route cable next to power
lines.
z Do not route cable near or over
Fluorescent Fixtures.
z Do not route cable next to
Speaker Wires.
z Do not install cable inside Power
Line Conduits.
z Avoid the use of staples that may
penetrate the cable.
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
INPUT 1 - USING A DESK BASE MICROPHONE
USING A PUSH-TO-TALK DESK BASE MICROPHONE
Microphone paging and precedence over AUX 1 or AUX 2 channels
may be accomplished by using a Desk Base or a Gooseneck
Microphone. Wire the Microphone output leads to the MIC input terminals as per Fig. 11A.
CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS
OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE
MADE WITH THE AMPLIFIER POWER OFF.
WIRING
Wire the Desk Base Microphone leads to the Microphone
MUTING: The Amplifier is equipped with two independent Muting
Input terminal strip as per diagram in Fig 11A. Check
Circuits:
Microphone instructions and connect HOT LEAD (B) to
Terminal HOT, COMMON LEAD (A) to Terminal COM and
SHIELD LEAD to Terminal G. Connect Muting Switch to
For additional information on the Muting operation refer Terminals MUTE 1 or MUTE 2 and G as shown.
to the Muting Functions section of this Manual.
DO NOT GROUND THE MICROPHONE CABLE SHIELD
TO THE CHASSIS OF THE AMPLIFIER
z
z
Direct Muting by shorting the MUTE Terminals
Automatic Muting with VOX - Voice Activated Muting
MUTING - PRIORITY SETTINGS
Direct Muting is provided by the Desk Base Muting Switch wired as
per diagram in Fig. 11A. If Auto-Mute (VOX) is desired follow instructions below. The Desk Base Muting Switch can be omitted.
Push to Talk Key
MUTING INPUT 4/AUX 1 (MUSIC INPUT)
To mute Input 4/AUX 1 (Music Input) when Paging from MIC 1, set INPUT
4/AUX 1 MUTE 1 JUMPER to ON Position. Each time MIC 1 is activated
the Program on Input 4/AUX 1 is automatically muted by the VOX.
b50side
Fig. 11 - Desk Base Microphone
DESK BASE/GOOSENECK MICROPHONE WITH MUTING SWITCH
INPUT 1 - Default Jumper Settings
The Diagram at Left shows the
Default Settings for INPUT 1.
VOX 1 is SWITCHED ON
VOX 2 is SWITCHED OFF
MUTE 1 is SWITCHED OFF
MUTE 2 is SWITCHED OFF
VOX - MUTE JUMPERS SETTING
SW215
VOX 1 BUSS
ACTIVATED
OFF
V1
JUMPER
VOX SEND
X
V2
MIC IN
G
M2
When the INPUT 1 (MIC 1) is
activated the VOX 1 BUSS is ON
and it will MUTE any Input with the
MUTE 1 Setting SWITCHED ON.
MUTE 1
MUTE 2
= JUMPER
GROUND
VOX 2 BUSS OFF
MASTER
REMOTE
VOLUME
M1 RVC RVC
AUDIO OUT
Push to Talk Key
INPUT 1
250ohm 1.5mV
BALANCED
SW220
OFF
M1
MUTE RECEIVE
M2
Connect Desk Base or Gooseneck
Microphone as per diagram below.
Connect Muting Switch to MUTE 1
or MUTE 2 and G Terminals.
If using the VOX system the
muting switch is unnecessary.
JUMPER
MUTE 1 BUSS OFF
X
X
INPUT 1 (MIC)
INPUT 2 (MIC)
INPUT 3 (MIC)
G COM HOT
G COM HOT
G COM HOT
MUTE 2 BUSS OFF
MUTING SWITCH
NOTE: To change the
INPUT Default Settings
refer to the appropriate
section in this Manual
SHIELD
A
MIC
Lo Z
B
3120 Micbase 01
Fig. 11A - Input 1 and Muting Terminals
DMS3040/3080/3120
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 11
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
CAUTION !
REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD
ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET
THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE
PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY.
TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SERVICING UNLESS YOU
ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.
INPUT CONNECTIONS
CONDENSER AND ELECTRET MICROPHONES
PHANTOM POWER SELECTORS
CONDENSER AND ELECTRET TYPE MICROPHONES
Condenser and Electret Microphones require a DC Operating
Voltage. The Amplifier provides this operating voltage or Phantom
Power selectively on Inputs.1-2-3-4-5.
PHANTOM POWER SELECTOR JUMPER
By following the Main Printed Board Layout locate the Selector
Jumpers with the ID No. as indicated on the Table below.
Prior to selecting the Condenser or Electret Microphone be sure
that the Operating Voltage and Output Impedance of the device
match the Input characteristics of the Amplifier listed below.
Phantom Power
Input Impedance
= 18 Volt DC
= 250 to 600 ohm
ACCESS TO PHANTOM POWER SELECTORS
1) Remove Power Cord from AC Outlet.
2) Remove the three screws on each side of the Amplifier.
3) Lift Cover and carefully slide Cover out towards the rear.
4) Jumpers are located on the Main Printed Circuit Board.
Reset the Phantom Power Jumpers for INPUT 1 - 2 or 3 to the ON
position as desired. Lift the Mini Jumper out of the socket pins and
re-position to the ON position. Make sure the Jumper is lined up
with the socket pins.
INPUT 4 and 5 CONFIGURED AS MIC INPUTS
If INPUT 4 and INPUT5 need to be configured as Microphone
Inputs, reset the Phantom Power Jumpers as well as the
Switches provided for the two Inputs as indicated in the Table
below.
WIRING
CONDENSER/ELECTRET MICROPHONE
Carefully follow the wiring instruction packed with the Microphone
used. Attach the microphone leads to the terminal strip as per diagram per Fig. below.
DO NOT GROUND THE MICROPHONE CABLE SHIELD TO THE
CHASSIS OF THE AMPLIFIER
CONFIGURATION TABLES
BALANCED CONDENSER/ELECTRET MICROPHONE WIRING
MIC INPUTS PHANTOM POWER JUMPER SETTING
WHEN USING ELECTRET MICROPHONES
INPUT 1
On
JUMPER
OFF
Input
SW201
INPUT 2
On
JUMPER
SW202
INPUT 3
On
JUMPER
INPUT 4
On
On
JUMPER
MIC 4
MIC 5
MIC 5
250ohm 1.5mV
BALANCED
OFF (When set as MIC 4)
SW204
INPUT 5
SW228
SW208
SW229
INPUT 1 (MIC)
INPUT 2 (MIC)
INPUT 3 (MIC)
G COM HOT
G COM HOT
G COM HOT
OFF (When set as MIC 5)
SW207
-0 +18V +18V
SHIELD
MIC
Lo Z
Input
Switch No. Setting
INPUT 4
INPUT 5
INPUT 5
SW228
SW208
SW229
AUX 1
AUX 2
AUX 2
OFF
SW203
JUMPER
Switch No. Setting
INPUT 4
INPUT 5
INPUT 5
OFF
INPUT 4 - 5 DEFAULT
SWITCH SETTINGS
INPUT 4 - 5 SWITCH SETTINGS WHEN
CONFIGURING AS MICROPHONE INPUT
INPUT 1- 2 - 3 - 4 - 5 DEFAULT
JUMPER SETTINGS
Input
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
Jumper No.
SW201
SW202
SW203
SW204
SW207
Setting
OFF
OFF
OFF
OFF
OFF
HOT LEAD
HOT LEAD
3120 Micbal Electret
Fig. 12 - Balanced Condenser/Electret Microphone Wiring - Configuration Tables
PAGE 12
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
PAGING FROM THE TELEPHONE SYSTEM
CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE MADE
WITH THE AMPLIFIER OFF (POWER OFF).
DMS
OUTPUT LEVEL
TM
DIGITAL MUSIC AMPLIFIER
TEL
PEAK
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
POWER
0
10
INPUT 1
0
10
INPUT 2
0
10
INPUT 3
0
10
INPUT 4/AUX 1
0
10
0
INPUT 5/AUX 2
10
MODULE
-10
+10
BASS
-10
O
+10
TREBLE
DMS Amplifier
Telephone
KSU
Key Service Unit
telpagin
Fig. 13 - Connecting to the Telephone Paging KSU
WIRING - The Amplifier is interface ready for the Telephone
line in applications requiring paging from the telephone system. The Telephone line Paging Output (Tip and Ring) can
be directly connected to the TEL input and to the HOT and
COM as shown in the wiring diagram Fig. 12A
.
CABLE - Use a two conductor twisted wire.
OUTPUT LEVEL CONTROL - Use TEL OUTPUT LEVEL
Control located on the Rear panel. After wiring adjust control for the desired output level.
VOICE ACTIVATED MUTING (VOX) - Muting of the AUX 1
channel (music muting) during Paging is automatic via the
Voice Activated Muting System. No contact closure for the
Muting Circuit is required from the Telephone system. For
additional information on the Muting operation refer to the
Muting Functions section of this Manual.
NOTE: The Telephone Paging Input is a Transformer
Balanced 600 ohm input.
DO NOT GROUND THE TIP OR RING WIRE TO THE
CHASSIS OF THE AMPLIFIER
PHONE PAGING PRIORITY OVER MICROPHONES Priority over any Microphone Input may be accomplished by
setting the MIC Inputs MUTE Jumpers.
TELEPHONE SYSTEM PAGING WIRING
BALANCED TELEPHONE PAGING WIRING
TEL INPUT - Default Jumper Settings
The Diagram at Left shows the
Default Settings for TEL INPUT.
VOX 1 is SWITCHED ON
VOX 2 is SWITCHED OFF
MUTE 1 is SWITCHED OFF
MUTE 2 is SWITCHED OFF
VOX - MUTE JUMPERS SETTING
OFF
V1
SW214 VOX 1 BUSS
ACTIVATED
JUMPER
VOX SEND
X
V2
VOX 2 BUSS OFF
JUMPER
TEL IN
When the TEL INPUT (PHONE) is
activated the VOX 1 BUSS is ON
and it will MUTE any Input with the
MUTE 1 Setting SWITCHED ON.
= JUMPER
PAGING OUT
TEL INPUT
TEL
SW216
MUTE RECEIVE
M1
M2
OFF
JUMPER
G COM HOT
MUTE 1 BUSS OFF
X
X
600 ohm 100 mV
BALANCED
MUTE 2 BUSS OFF
Telephone System
Paging Output
RING
NOTE: To change the
INPUT Default Settings
refer to the appropriate
section in this Manual
TIP
3120 Telpaging 01
Fig. 13A - Balanced Telephone Input Wiring
DMS3040/3080/3120
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 13
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
SETTING INPUT 4 AS AUX 1
INPUT 4/AUX 1 DEFAULT SETTING
DEFAULT JUMPERS AND SWITCH SETTING
SW212 = OFF
SW217 = M 1
SW228 = AUX 1
OFF
V1
JUMPER
VOX 1 BUSS OFF
X
X
V2
INPUT 4
AUX 1
MUSIC OUT
AUX 1 - MIC 4 SWITCH
SW228
MIC 4
18
WHEN
MIC
1
IS
ACTIVATED THE VOX 1
BUSS IS SWITCHED-ON
AND
THE
SIGNAL
PRESENT
ON THE
MUTE 1 BUSS WILL
MUTE
THE
MUSIC
FROM INPUT 4/AUX 1
SW217
OFF
M1
AUX 1
M2
Input 1-4 - V1 - 01
MUTE 1 BUSS ON
X
MUTE 2 BUSS OFF
SATELLITE RECEIVER
AM/FM TUNER
INPUT-5(AUX2)
47kohm 100mV
TRACK
L
(AUX2)
ATTENUATOR
R
CD
TAPE DECK
MUSIC OUTPUT
R
19
INPUT - 4 (AUX1)
47 kohm 100 mV
AUX 1
ATTENUATOR
STEREO SUMMING
Most Music Source Devices provide a Stereo Output.
Accordingly the Amplifier is equipped with two Jacks for the
AUX 1 Input (L and R). The two Inputs are internally
buffered and electronically mixed to Mono. This system
ensures that the Music Device is properly loaded and that
the Stereo Signals are correctly summed (L+R) to Mono
without distortion.
CABLE
To connect the music source devices to the AUX 1 Input
use two single conductor shielded audio cable terminated
in a single prong phono plug on both ends.
L
AUX 1 INPUT MUTING
R
3120 Stereo Summ
Fig. 14A - Stereo Summing and AUX 1 Input Attenuator
PAGE 14
TYPICAL OUTPUT LEVEL OF MUSIC DEVICES:
Satellite Receivers
= 1 to 5 Volt
Digital Tuners/Receivers
= 100 to 300 Mv
CD Players/Changers
= 2 to 3 Volt
Tape Decks
= 500 to 700 Mv
L
Fig. 14 - Rear Panel AUX 1 Input Diagram
18
AUX 1 SENSITIVITY ATTENUATOR (Reference. 18)
The AUX 1 Input is equipped with a Sensitivity Attenuator
that allows the interface of the Input with Devices having a
wide range of Output Levels.
SETTING THE AUX 1 INPUT ATTENUATOR
Connect a Music Source to the Amplifier.
Turn Attenuator (rear panel) fully counterclockwise.
Turn INPUT 4 Front Panel Control to midway.
Switch Amplifier and Music Source ON.
Turn Attenuator Control (rear panel) until desired Output
Level is achieved.
Adjust INPUT 4 Front Panel Level Control Up-Down as
desired.
CD PLAYER
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
L
AUX 1
INPUT 4 SET AS AUX 1 (Reference. 19)
The AUX 1 input is provided for high level program source.
The output from a Satellite Receiver, Tuner, Tape Cassette
Deck, CD Player or other high level program source may
be directly connected to this input.
01
R
3120 Aux1 01
= OFF
=M1
= AUX 1
By adjusting the Input Sensitivity to the level that matches
the device used the correct interface with the Amplifier is
achieved resulting in lower overall distortion and better frequency response characteristics.
paso
AUX 1
ATTENUATOR
SW212 - VOX JUMPER
SW217 - MUTE JUMPER
SW228 - AUX1-MIC4 SWITCH
JUMPER
19
INPUT - 4 (AUX1)
47 kohm 100 mV
FACTORY SETTING
VOX 2 BUSS OFF
SW212
MUSIC
IN
JUMPERS/SWITCH NO.
MUTING - WHEN MIC 1 OR THE TEL IN ARE ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND
THE SIGNAL PRESENT ON THE MUTE 1 BUSS
WILL MUTE THE MUSIC FROM AUX 1.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
SETTING INPUT 5 AS AUX 2
INPUT 5/AUX 2 DEFAULT SETTING
DEFAULT JUMPERS AND SWITCH SETTING
SW213 = OFF
SW223 = M 1
SW208 = AUX 2
SW229 = AUX 2
MUSIC
IN
V1
OFF
VOX 1 BUSS OFF
X
X
V2
MUSIC OUT
INPUT 5
AUX 2
SW208 and SW229
OFF
M1
M2
Input 1-4 - V1 - 01
WHEN
MIC
1
IS
ACTIVATED THE VOX 1
BUSS IS SWITCHED-ON
AND
THE
SIGNAL
PRESENT
ON THE
MUTE 1 BUSS WILL
MUTE
THE
MUSIC
FROM INPUT 5/AUX 2
INPUT 5 SET AS AUX 2 (Reference. 20)
The AUX 2 input is provided for high level program source.
The output from a Jukebox, Tuner, Tape Cassette Deck,
CD Player or other high level program source may be
directly connected to this input.
MUTE 1 BUSS ON
X
MUTE 2 BUSS OFF
SET TO AUX 2
paso
INPUT 5 (AUX 2)
47 Kohm 100 mV
L
AM/FM TUNER
TRACK
(AUX 2)
ATTENUATOR
01
CD PLAYER
R
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
3120 Aux2 01
L
R
MUSIC OUTPUT
CD
TAPE DECK
R
L
Fig. 15 - Rear Panel AUX 2 Input Diagram
20
21
INPUT 5 (AUX 2)
47 Kohm 100 mV
L
(AUX 2)
ATTENUATOR
R
TYPICAL OUTPUT LEVEL OF MUSIC DEVICES:
Satellite Receivers
= 1 to 5 Volt
Digital Tuners/Receivers
= 100 to 300 Mv
CD Players/Changers
= 2 to 3 Volt
Tape Decks
= 500 to 700 Mv
By adjusting the Input Sensitivity to the level that matches
the device used the correct interface with the Amplifier is
achieved resulting in lower overall distortion and better frequency response characteristics.
SETTING THE AUX 2 INPUT ATTENUATOR
Connect a Music Source to the Amplifier.
Turn Attenuator (rear panel) fully counterclockwise.
Turn INPUT 5 Front Panel Control to midway.
Switch Amplifier and Music Source ON.
Turn Attenuator Control (rear panel) until desired Output
Level is achieved.
Adjust INPUT 5 Front Panel Level Control Up-Down as
desired.
STEREO SUMMING
Most Music Source Devices provide a Stereo Output.
Accordingly the Amplifier is equipped with two Jacks for the
AUX 1 Input (L and R). The two Inputs are internally
buffered and electronically mixed to Mono. This system
ensures that the Music Device is properly loaded and that
the Stereo Signals are correctly summed (L+R) to Mono
without distortion.
CABLE
To connect the music source devices to the AUX 1 Input
use two single conductor shielded audio cable terminated
in a single prong phono plug on both ends.
INPUT 5
MIC-AUX2
3120 Stereo Summ 01
Fig. 15A - Stereo Summing and AUX 2 Input Attenuator
DMS3040/3080/3120
AUX 2 SENSITIVITY ATTENUATOR (Reference. 21)
The AUX 2 Input is equipped with a Sensitivity Attenuator
that allows the interface of the Input with Devices having a
wide range of Output Levels.
SATELLITE RECEIVER
21
AUX 1
ATTENUATOR
OFF
M1
AUX 2
AUX 2
AUX 2
JUMPER
MIC 5
INPUT - 4 (AUX1)
47 kohm 100 mV
=
=
=
=
- VOX JUMPER
- MUTE JUMPER
- AUX 2-MIC 5 SWITCH
- AUX 2-MIC 5 SWITCH
VOX 2 BUSS OFF
SW223
20
FACTORY SETTING
SW213
SW223
SW208
SW229
SW213
AUX 2 - MIC 5 SWITCH
AUX 2
JUMPER
JUMPERS/SWITCH NO.
AUX 2 INPUT MUTING
MUTING - WHEN MIC 1 OR THE TEL IN ARE ACTIVATED THE VOX 1 BUSS IS SWITCHED-ON AND
THE SIGNAL PRESENT ON THE MUTE 1 BUSS
WILL MUTE THE MUSIC FROM AUX 2.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 15
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
ADDRESSABLE DUAL VOX SYSTEM
VOX - VOICE ACTIVATED MUTING
VOX SENSITIVITY CONTROLS
DUAL VOX - VOICE ACTIVATED MUTING - The Amplifier
is equipped with a DUAL noiseless, fast acting Logic VOX
Switching System. When any of the INPUTS are activated
and a Signal is present on a given INPUT and either VOX 1
or VOX 2 or BOTH are Switched-ON (using internal
Jumpers) then the MUTE 1 or MUTE 2 BUSS or BOTH are
ACTIVE. If any of the INPUTS have the MUTE 1 or MUTE
2 Switched-ON (by Internal Jumpers) then the INPUT (or
INPUTS) will be MUTED according to the Jumpers Setting.
Once the SIGNAL-ON on the ACTIVE INPUT is terminated
the normal functions are automatically restored on all muted
inputs.
ACCESS TO VOX AND MUTE JUMPERS
REFER TO JUMPERS AND SWITCHES INTERNAL
ACCESS.
CAUTION: PRIOR TO PERFORMING THE ABOVE OPERATION BE SURE TO FOLLOW THE SAFETY NOTES
REFERRING TO THE REMOVAL OF THE AMPLIFIER
COVER.
VOX SENSITIVITY CONTROLS
VOX 1 AND VOX 2 SENSITIVITY CONTROLS
The VOX 1 and VOX 2 Sensitivity Controls set the sensitivity level at which point the VOX 1 and VOX 2 are respectively engaged during INPUT ACTIVATION. The VOX Sensitivity
Controls are located on the Amplifier Rear Panel.
VOX 1 SENSITIVITY CONTROL = Reference 33
VOX 2 SENSITIVITY CONTROL = Reference 32
VOX-1
SENS
VOX-2
SENS
MUTE-2
DELAY
33
32
31
DMS3120 Vox Sens 01
Fig. 16 - Rear Panel VOX 1 and VOX 2 Sensitivity Control
and MUTE 2 Delay Control
VOX SENSITIVITY ADJUSTMENT
VOX SENSITIVITY ADJUSTMENT
1) Turn all Front Panel Input Level Controls to 0.
2) Turn VOX Sensitivity Control counterclockwise until it
stops.
3) Connect a Signal Source (Microphone, Telephone or
Music) to the respective Input Terminals (For connection
details refer to the appropriate section in this Manual).
4) While talking from a Paging Source (Microphone or
Telephone) or Playing Music rotate the INPUT LEVEL CONTROLS (Front Panel) until the desired output level is
achieved.
5) While talking from a Paging Source (Microphone or
Telephone) or Playing Music, turn the Sensitivity Control
(VOX 1 or VOX 2) slowly clockwise until the Muting (MUTE
1 or MUTE 2) is activated.
VOX JUMPERS DEFAULT SETTING TABLE
JUMPER
ID NO.
JUMPER
REFERENCE
FUNCTION
DESCRIPTION
FACTORY
SETTING
FACTORY
SETTING
MAIN PCB JUMPERS
SW210
INPUT 2 -
VOX1 - VOX2 - OFF
OFF
SW211
INPUT 3 -
VOX1 - VOX2 - OFF
OFF
SW212
INPUT 4 -
VOX1 - VOX2 - OFF
OFF
SW213
INPUT 5 -
VOX1 - VOX2 - OFF
OFF
SW214
TEL IN -
VOX1 - VOX2 - OFF
V1
SW215
INPUT 1 -
VOX1 - VOX2 - OFF
V1
SW221
MODULE -
VOX1 - VOX2 - OFF
PAGE 16
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
OFF
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
ADDRESSABLE DUAL MUTING SYSTEM
DIRECT MUTING
DUAL MUTING SYSTEM - The Amplifier is equipped with a DUAL
noiseless, fast acting Logic MUTING Switching System. When any
of the INPUTS are activated and a Signal is present on a given
INPUT and either VOX 1 or VOX 2 or BOTH are Switched-ON
(using internal Jumpers) then the MUTE 1 or MUTE 2 BUSS or
BOTH are ACTIVE. If any of the INPUTS have the MUTE 1 or
MUTE 2 Switched-ON (by Internal Jumpers) then the INPUT (or
INPUTS) will be MUTED according to the Jumpers Setting. Once
the SIGNAL-ON on the ACTIVE INPUT is terminated the normal
functions are automatically restored on all muted inputs.
DIRECT MUTING - Direct Muting may be accomplished by shorting the MUTE 1 and MUTE 2 Terminals to the G Terminal through
an external switch. Each time the Muting Switch is closed the corresponding MUTE BUSS is activated.
WIRING
G
M2
MUTE 1
MUTE 2
MUTE-2
DELAY
GROUND
10
MASTER
REMOTE
VOLUME
M1 RVC RVC
ACCESS TO MUTE JUMPERS
REFER TO JUMPERS AND SWITCHES INTERNAL ACCESS.
CAUTION: PRIOR TO PERFORMING THE ABOVE OPERATION
BE SURE TO FOLLOW THE SAFETY NOTES REFERRING TO
THE REMOVAL OF THE AMPLIFIER COVER.
31
MUTING TIMING - The MUTING is preset for -60 db Attenuation.
When MUTE 1 or 2 are activated the MUTE BUSS is instantaneously Switched-ON. When the Muting is deactivated the program source is gradually restored.
MUTING SWITCH M 2
3120 M1 - M2 01
Fig. 17 - Direct Muting Terminals and Diagram
MUTE 1 (M1) = TIMING PRESET 2-3 SECONDS
MUTE 2 (M2) = TIMING ADJUSTABLE 3-30 SECONDS
MUTE 2 DELAY = USE REAR PANEL CONTROL Reference 31
MUTE 2 DELAY - The M 2 Delay can be adjusted by using the
MUTE 2 DELAY CONTROL on the rear panel (reference 31).
MUTE 1
Signal
Level
Terminals
shorted
Program
Attenuation
60 dB
2-3
sec.
MUTING SWITCH M 1
Signal
Level
Program
gradually
restored
MUTE 2
Terminals
shorted
Program
Attenuation
60 dB
Mute terminals
opened
Adjustable
from
3 to 30
seconds
Program
gradually
restored
Mute terminals
opened
time
time
DMS mutfunct 01
DMS mutfunct 02
Fig. 17B - M 1 Function Timing Diagram
Fig. 17C - M 2 Function Timing Diagram
MUTE JUMPERS DEFAULT SETTING TABLE
JUMPER
ID NO.
JUMPER
REFERENCE
FUNCTION
DESCRIPTION
FACTORY
SETTING
FACTORY
SETTING
MAIN PCB JUMPERS
SW206
SW216
SW217
SW218
SW219
SW220
SW222
SW223
SW227
DMS3040/3080/3120
VOX RELAY TEL IN INPUT 4/AUX 1 INPUT 3 INPUT 2 INPUT 1 MODULE INPUT 5/AUX 2 CHIME TRIGGER -
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
1
1
1
1
1
1
1
1
1
-
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
2
2
2
2
2
2
2
2
2
M1
-
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
OFF
M1
OFF
OFF
OFF
OFF
M1
M1
PAGE 17
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
CAUTION !
REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD
ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET
THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE PROVIDED
FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SERVICING UNLESS YOU ARE QUALIFIED TO DO SO.
INPUT 1 (MIC 1) UNMUTING FUNCTION
WIRING
DIRECT UNMUTING
MICROPHONE WITH UNMUTING ZONE SWITCH
INPUT 1 (MIC 1) UNMUTING FUNCTION
The Input 1 (MIC 1) can be preset to be normally MUTED (INPUT
OFF) when the JUMPER SW205 - MIC 1 UNMUTE - IS SET TO
THE ON POSITION. The MIC 1 is SWITCHED-ON when the
UNMUTE and G Terminals are shorted by a Switch Contact
Closure. This function allows for a multi zone installation using two
or more Amplifiers and a single Microphone and Zone Switches.
When the Jumper SW205 is set to the ON Position the Microphone
Input is OFF and it is turned ON when the UNMUTE and the G terminals are closed by a switch.
JUMPER NO.
FUNCTION
SW205
Connect Paging Microphone
as per diagram below
(reference 30). Connect Zone
Unmuting Switch to UNMUTE
(reference 9) and G Terminals.
The VOX (if ON) feature will
automatically mute the Music
GROUND
MUTE 2
MIC1
G
M2
MUTE 1
UNMUTE
9
MASTER
REMOTE
VOLUME
M1 RVC RVC
30
250ohm 1.5mV
BALANCED
POSITION SET
MIC 1 Muted
ON
INPUT 1 (MIC)
INPUT 2 (MIC)
G COM HOT
G COM HOT
If the Jumper requires resetting follow the instruction below.
ZONE UNMUTING SWITCH
ACCESS TO UNMUTING JUMPER
1) Remove Power Cord from AC Outlet.
2) Remove the three screws on each side of the Amplifier
securing the Top Cover to the Chassis.
3) Lift Cover and carefully and slide Cover out towards the rear.
4) On the Main Amplifier Printed Board locate the SW205 MIC 1 UNMUTE Jumper Set.
5) Set Jumper to the ON position.
MIC
Lo Z
SHIELD
A = Common
B = Hot
A
B
3120 Unmute 01
Fig. 18 - Microphone and Zone Unmuting Diagram
2 - ZONE
PAGING SELECTORS
UNMUTE - VOX AND MUTE JUMPER
SETTINGS ON AMPLIFIERS 1 & 2
V1
V2
JUMPER
SW215
On
JUMPER
SW205
2
ZONE 1
ZONE 2
INPUT 4
AUX 1
MIC 1
UNMUTE
OFF
OFF
M1
M2
JUMPER
SW217
MUTE 1 ON
OFF
VOX 1 ON
INPUT 1
MIC 1
1
3120 Unmute Jump Set
SPST ZONE
SWITCHES
TO AMP 1
TO AMP 2
Fig. 18A - 2 - Zone System Jumper Settings
The Fig. at right shows a typical 2 Zone Switching
Panel. Use SPST Momentary Contact Switches. See
complete 2 - Zone Wiring Diagram provided in this
Manual.
TO MIC INPUT
3120 2 Zone Diagram 01
PAGING MICROPHONE
Fig. 18B - 2 - Zone Switching Panel
PAGE 18
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
LINE FUSE
5A 250V
GROUND
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
ZONE 2
LEVEL
LEVEL
8
MOH OUT 1 WATT
0
8
1 WATT
0
ZONE 2
25V/70V Speaker
SPEAKER OUTPUT
LINE FUSE
5A 250V
ZONE 2
LEVEL
25V/70V Speaker
SPEAKER OUTPUT
VOX-2
SENS
C
+
-
VOX-1
SENS
MUTE-2
DELAY
25V/70V Speaker
VOX-2
SENS
120 W RMS
117V 60 HZ
850 VA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
M2
G COM HOT
INPUT 1 (MIC)
G
CAUTION
G COM HOT
INPUT 1 (MIC)
INPUT 2 (MIC)
G COM HOT
OUT
MIX
BUSS
G
PRE
OUT
SUB OUT
PRE EQ
MIX
BUSS
INPUT 3 (MIC)
COM HOT RVC RVC
INPUT 4 (MIC)
G
250ohm 1.5mV
BALANCED
G COM HOT
G COM HOT
TEL
600 ohm 100mV
TEL OUTPUT
LEVEL
INPUT 5
MIC-AUX 2
BY INTERNAL
SWITCH
G COM HOT
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
R
(AUX2)
ATTENUATOR
L
COMMON
HOT
CAUTION: REMOVE
POWER CORD FROM
AC OUTLET PRIOR TO
INSTALLING MODULE
PORT ACCEPTS
STANDARD
MODULE
3120 2 Zone Diagram
CAUTION: REMOVE
POWER CORD FROM
AC OUTLET PRIOR TO
INSTALLING MODULE
PORT ACCEPTS
STANDARD
MODULE
GROUND (SHIELD)
TEL OUTPUT
LEVEL
INPUT-5(AUX2)
47kohm 100mV
600 ohm 100mV
(AUX1)
ATTENUATOR
R
(AUX2)
ATTENUATOR
L
INPUT-5(AUX2)
47kohm 100mV
INPUT 5
MIC-AUX 2
BY INTERNAL
SWITCH
G COM HOT
TEL
INPUT-4(AUX1)
47kohm 100mV
G COM HOT
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
COM HOT RVC RVC
INPUT 4 (MIC)
INPUT-4(AUX1)
47kohm 100mV
(AUX1)
ATTENUATOR
OFF
ON
POWER SUB OUT LINE OUT TONE
IN
POST EQ
600
BYPASS
EQ LINK
EQ LINK
IN
SUB OUT
PRE EQ
250ohm 1.5mV
BALANCED
G COM HOT
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
US 30TJ
PRE
OUT
OFF
ON
POWER SUB OUT LINE OUT TONE
POST EQ
IN
600
BYPASS
INPUT 3 (MIC)
GROUND
MASTER
REMOTE
VOLUME
M1 RVC RVC C
RISK OF ELECTRIC SHOCK
DO NOT OPEN
M2
OUT
EQ LINK
IN
EQ LINK
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
30TJ
US
UNMUTE
G COM HOT
INPUT 2 (MIC)
WARNING: THIS APPLIANCE
MUST BE EARTHED
MIC1
DMS3120
NO
DIGITAL MUSIC AMPLIFIER
PROFESSIONAL AUDIO & SOUND
NC
VOX RELAY
24V DC
250 mA
G
WARNING: THIS APPLIANCE
MUST BE EARTHED
MIC1
120 W RMS
117V 60 HZ
850 VA
MUTE-2
DELAY
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
SER. NO.
-
DIGITAL MUSIC AMPLIFIER
25V/70V Speaker
SER. NO.
+
DMS3120
NO
MUSIC SOURCE LINE
V2
V1
SW215
JUMPER
INPUT 1
MIC 1
OFF
ZONE 1
ZONE 2
2
On
SW205
JUMPER
M2
M1
SW217
JUMPER
INPUT 4
AUX 1
OFF OFF
MIC 1
UNMUTE
JUMPERS SETTING
ON AMPLIFIERS 1 & 2
SPST
SWITCHES
1
2 ZONE PAGING
SELECTORS
MICROPHONE WIRE
2 Conductor Shielded
Paging Microphone can be
Unswitched and always ON
PAGING MICROPHONE
SATELLITE RECEIVER
MUSIC OUTPUT
DIGITAL MUSIC AMPLIFIERS
OPERATION - A 2 - Zone Paging Wiring Diagram Application is provided. The Paging Microphone is connected in parallel to all the Microphone Inputs. Two
Independent SPST Switches are provided for the Paging Zone Selection. MUSIC - The MUSIC SOURCE (Satellite Receiver) is cascade connected to the
two Amplifiers. ZONE PAGING - When one or more Zone Switches are activated the UNMUTE Function OPENS the Microphone Channel on the Amplifier
selected and the MICROPHONE is active for the PAGING. Simultaneously the MUSIC is MUTED ONLY ON THE ZONE (OR ZONES) SELECTED.
Independent MUSIC SOURCE may be provided to each of the Amplifiers if required. MOH - MUSIC ON HOLD is available from each of the Amplifiers used.
The MOH source maybe selected from either the AUX 1, AUX 2 or the MODULE Input and is immune to Paging or the MUTE/UNMUTE Function.
25V/70V Speaker
GROUND
C
PROFESSIONAL AUDIO & SOUND
NC
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
VOX-1
SENS
BALANCED
ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE
CAUTION: TO REDUCE THE RISK OF FIRE OR OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE
SHOCK DO NOT EXPOSE THIS APPLIANCE TO OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN
RAIN OR MOISTURE. DO NOT REMOVE COVER. REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER
THERE ARE NO USER SERVICEABLE PARTS UNE PERSONNE QUALIFIEE
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
COM 8
25V 70V
ZONE 2
117V 60HZ
117V 500W MAX
UNSWITCHED
8
1 WATT
0
GROUND
MASTER
REMOTE
VOLUME
M1 RVC RVC C
MUSIC SOURCE LINE
CAUTION: TO REDUCE THE ATTENTION: AFIN DE REDUIRE LE RISQUE
D'INCENDIE REMPLACER SEUL PAR UN
RISK OF FIRE, REPLACE
ZONE 1
FUSIBLE DE MEME TYPE.
ONLY WITH SAME TYPE
FUSE.
ZONE 1
0
600
25V/70V Speaker
ZONE 1
117V 60HZ
117V 500W MAX
UNSWITCHED
8
MOH OUT 1 WATT
0
BALANCED
ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE
CAUTION: TO REDUCE THE RISK OF FIRE OR OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE
SHOCK DO NOT EXPOSE THIS APPLIANCE TO OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN
RAIN OR MOISTURE. DO NOT REMOVE COVER. REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER
THERE ARE NO USER SERVICEABLE PARTS UNE PERSONNE QUALIFIEE
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
COM 8
25V 70V
LEVEL
GROUND
GROUND
24V DC
250 mA
UNMUTE
UNMUTE
VOX RELAY
MUTE 1
MUTE 1
ZONE 2
MUTE 2
MUTE 2
CAUTION: TO REDUCE THE ATTENTION: AFIN DE REDUIRE LE RISQUE
D'INCENDIE REMPLACER SEUL PAR UN
RISK OF FIRE, REPLACE
ZONE 1
FUSIBLE DE MEME TYPE.
ONLY WITH SAME TYPE
FUSE.
ZONE 1
0
600
UNMUTE
2 ZONE PAGING AND MUSIC WIRING DIAGRAM
VOX 1 ON
DMS3040/3080/3120
MUTE 1 ON
®
TM
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC SERIES
INSTALLATION AND WIRING
Fig. 19 - 2 Zone Paging and Music System
PAGE 19
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
EXTERNAL EQUALIZER LINK
SET EQ LINK SWITCH TO
IN
SET TONE BY PASS SWITCH TO
CONNECTING TO AN EXTERNAL EQUALIZER
The Amplifier is equipped with an External Equalizer Link
to allows the use of an External Equalizer for applications
requiring Frequency Selective Acoustic Correction. The
Amplifier is furnished with the two jacks of the Link bridged
by a SELECTOR SWITCH. When the EQ LINK Switch
(REFERENCE 12) is the IN position the internal
Preamplifier to Amplifier Link (Reference 13) is broken
allowing the insertion of an External Equalizer.
13
EXTERNAL EQUALIZER
12
17
paso
PRE
OUT
ON
IN
EQ LINK
To Input of Equalizer
OUT
To Output of Equalizer
EQ LINK
POWER
IN
ON
OFF
TONE
BYPASS
3120 EQlink
INSTALLATION TIPS
1) Use high quality, short length audio cables and position
the Equalizer in close proximity to the Amplifier. Avoid
mounting the EQ on top of the Amplifier unless is Rack
mounted.
2) Be sure that the Amplifier input controls and the EQ level
control are set at zero prior to turning the system On.
3) The Amplifier TONE BY PASS SWITCH (Reference 17)
should be set to ON ( linear response position).
4) Carefully adjust the EQ Level Control to avoid distortion
caused by excessive signal boost.
5) Follow the instructions supplied with the Equalizer.
WIRING
To connect to an External Equalizer use two (2) single conductor shielded audio cables terminated in a single prong
phono plug on both ends.
Fig. 20 - Rear Panel External Equalizer Link Diagram
MIX BUSS BRIDGING
MIX BUSS BRIDGING
15
BRIDGING TWO AMPLIFIERS
15
AMPLIFIER A
The MIX BUSS (Reference 15)
allows two Amplifiers to be bridged
and share all inputs.
AMPLIFIER B
MIX
BUSS
MIX
BUSS
All signal sources connected to all
the inputs are common to the output
of both amplifiers. Muting and level
controls operate in exactly the same
way as if only one amplifier was
used.
WIRING
ON
LINE OUT
600
3120 Mixbuss
ON
LINE OUT
600
CABLE
To bridge two amplifiers or to connect to an external Mixer use a single conductor shielded audio cable
terminated in a single prong phono
plug on both ends.
Fig. 20B - Rear Panel Mix Buss Bridging Diagram
PAGE 20
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
MASTER REMOTE VOLUME
INPUT 4 (AUX 1) REMOTE VOLUME
MASTER
REMOTE
VOLUME
RVC RVC
11
26
MASTER
REMOTE VOLUME
CONTROL 10 K ohm
POTENTIOMETER
INPUT 4
REMOTE
VOLUME
RVC RVC
INPUT 4 (AUX 1)
REMOTE VOLUME
CONTROL 10 K ohm
POTENTIOMETER
Paso Remote
Volume Control
RVC10W
3120 Remote Volume
Fig. 21 - Master Remote Volume Control Diagram
Fig. 21B - Input 4 Remote Volume Control Diagram
REMOTE VOLUME CONTROLS
The Amplifier features two independent Remote Volume Control Capability: The INPUT 4 (AUX 1) Remote Volume (Reference 26) and
the MASTER REMOTE VOLUME CONTROL (Reference 11). A 10 K ohm Potentiometer is required for either control. Mount the 10 K
Pot on a suitable Wall Plate or any other convenient surface and connect to the Amplifier RVC Terminals as shown in the Diagram. The
Paso Model RVC10W Decora Style Remote Volume Control may be used.
INPUT 4 (AUX 1) OPERATION
When connected the Remote Volume adjusts the INPUT 4 (AUX 1) Level only. Usually this input is utilized for the Music Source (Satellite
Receiver, CD Player, etc.).
MASTER VOLUME OPERATION
The Control is a Master Volume and controls all the Inputs of the Amplifier with the exception of the MOH and ZONE 1 and ZONE 2
Outputs.
CABLE
To connect the Remote Control to the Amplifier use a two conductor wire not less than AWG 24. While the Remote Volume System uses
DC rather than audio caution should be exercised in the layout of the wire. Always avoid routing next to power lines. If the total wire resistance exceeds 3 K ohm the Volume may not go down to zero.
REMOTE VOLUME CONTROL - OPTIONAL ACCESSORY
MODEL RVC10W REMOTE VOLUME CONTROL
Remote Volume Control Potentiometer. Single
Gang Decora Style Plate.
SPECIFICATIONS
Control: 10 K ohm High Quality Control.
Connection: 6” Two Wire, color coded (Black and
Red) Pigtails stripped and tinned. Color Finish:
White. Dimensions: Front Plate = 4.5” High, 2.75”
Wide. Depth: 0.5”. Mounting Hardware: Supplied.
Fig. 21C - RVC10W Front View
DMS3040/3080/3120
Fig. 21D - RVC10W Rear View
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 21
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
INSTALLING A MODULE
22
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
US 30TJ
RVC C
PRE
OUT
SUB OUT
PRE EQ
INPUT-4(AUX1)
47kohm 100mV
MIX
BUSS
INPUT-5(AUX2)
47kohm 100mV
L
(AUX1)
ATTENUATOR
EQ LINK
(AUX2)
ATTENUATOR
R
IN
OUT
EQ LINK
OFF
ON
POWER SUB OUT LINE OUT TONE
IN
POST EQ
600
BYPASS
WARNING: THIS APPLIANCE
MUST BE EARTHED
INPUT 2 (MIC)
G COM HOT
INPUT 3 (MIC)
INPUT 4 (MIC)
G COM HOT
G
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
COM HOT RVC RVC
G COM HOT
250ohm 1.5mV
BALANCED
INPUT 5
MIC-AUX 2
BY INTERNAL
SWITCH
TEL
TEL OUTPUT
LEVEL
G COM HOT
600 ohm 100mV
Insert into Module Connector
Gold
Contact
Connector
Top
Cable from
Amplifier
Printed Board
Copper Side
PORT ACCEPTS
STANDARD
MODULE
CAUTION: REMOVE
POWER CORD FROM
AC OUTLET PRIOR TO
INSTALLING MODULE
Side
View
Module Bottom
Front
View
3120 Module Install
Module Gold
Contacts
Fig. 22 - Rear Panel Module Installation Diagram
MODULE INSTALLATION
MODULE TYPE
The Amplifier accepts Audio Modules having a 6 Contact PCB Derivation. Module mounting panel should be 3” H., 1-3/8”
W. (78 X 35 mm).
INSTALLATION
CAUTION: REMOVE POWER CORD FROM AC OUTLET PRIOR TO INSTALLING A MODULE. BE SURE THAT THE
MODULE OUTPUT LEVEL CONTROL IS SET AT “0” PRIOR TO THE INSTALLATION.
1) Locate Rear Panel Module Port (Reference 22) and unscrew the two crosshead screws holding the cover and set aside.
2) Reach inside the Amplifier and gently pull-out the Module Blue Ribbon Connector. If the Connector is tied to the chassis remove the Amplifier Top Cover and with a cutter cut the Nylon Tie holding the connector.
NOTE: BE CAREFUL NOT TO CUT THE CONNECTOR WIRE HARNESS.
3) Pull-out the blue-ribbon connector through the port opening (do not pull-out wire harness excessively).
4) By keeping the connector gold contacts on the left insert the Module PCB contacts into the socket.
5) Push Module through port opening and secure to rear panel by using the two screws removed with the Module cover.
PAGE 22
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
MODULE CONNECTOR DIAGRAM
MODULE CONNECTOR
Connector
Gold
Top
Contact
6
6
6
Cable from
Amplifier
5
5
4
4
3
2
1
6 = + 24V DC
5 = Module Input
4 = Module Output
3 = Ground
2 = Mute Buss 1
1 = Mute Buss 2
5
3
3
4
2
3
1
2
1
TO
MODULE
Side
View
Front
View
Connector Contacts
PCB
CONNECTOR
CN201
3120 Module Schem
Fig. 23 - Module Connector Contacts Diagram
MODULE CONNECTOR DIAGRAM - The above Diagram indicates the function of each of the six contacts of the Module
Connector. The Module Blue Ribbon Connector is attached to a wire harness and left floating beyond the Module Port
Cover. The Wire Harness Amplifier End is attached to Connector No. CN201 and plugged into the mating connector on the
Main Printed Circuit Board.
MODULE DEFAULT SETTINGS
MODULE CONNECTOR
Connector
Gold
Top
Contact
PCB
CONNECTOR
CN201
6
6
5
5
4
4
Cable from
Amplifier
Front
View
3120 Module Functions
Side
View
OFF
JUMPER
VOX 1 BUSS OFF
X
X
V2
SW221 VOX 2 BUSS OFF
3
4
3
1
1
V1
5
2
2
VOX SEND
6
3
3
MODULE VOX - MUTE
JUMPERS AND INPUT SOURCE
SWITCH DEFAULT SETTING
Connector Contacts
6 = + 24V DC
5 = Module Input
4 = Module Output
3 = Ground
2 = Mute Buss 1
1 = Mute Buss 2
2
1
AUX 1 - AUX 2 SWITCH
SW209
MODULE OUTPUT
AUX 1 SOURCE
MODULE INPUT
AUX 1
TO
MODULE
OFF
M1
M2
AUX 2
JUMPER
AUX 2 SOURCE
MUTE 1 BUSS OFF
X
X
SW222
MUTE 2 BUSS OFF
MUTE RECEIVE
Fig. 23A - Module VOX - MUTE - INPUT SOURCE Default Settings
MODULE FUNCTIONS - The Module Port accepts a standard audio Module. When a Module is utilized several functions can be activated by the Jumpers and Switch provided
for this Input.
VOX SEND - The SW221 Jumpers Set activates the VOX 1
- VOX 2 SEND or both. When a Signal is present at the
Module Output (Contact 4) then the VOX BUSS selected will
be active.
MUTE RECEIVE - The SW222 Jumpers Set activates the
DMS3040/3080/3120
MUTE 1 - MUTE 2 RECEIVE or both. When a Signal is present at the MUTE BUSS 1 or MUTE BUSS 2 the MODULE
will be MUTED accordingly.
INPUT SOURCE - The SW209 Switch selectes the Input
Source for the Module either AUX 1 or AUX 2. The Signal
present at either Input will be sent to the MODULE INPUT
(Contact 5).
By selecting the proper Setting several functions can be
derived from the Module.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 23
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
6
ZONE 2
0
600
0
0
8
MOH OUT 1 WATT
117V 500W MAX
UNSWITCHED
BALANCED
CAUTION: TO REDUCE THE RISK OF FIRE OR
SHOCK DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. DO NOT REMOVE COVER.
THERE ARE NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
COM
ZONE 2
LEVEL
8
1 WATT
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC AMPLIFIER
8
25V
70V
GROUND
117V 60HZ
LINE FUSE
5A 250V
SW702
ZONE 2 INPUT SOURCE
DEFAULT JUMPER SETTING
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
VOX-1
SENS
SPEAKER OUTPUT
CLASS 2 WIRING ACCEPTABLE
SER. NO.
AUX 2
ZONE 1
ZONE 1
LEVEL
MODULE
CAUTION: TO REDUCE THE
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE
FUSE.
AUX 2
MODULE
4
2
JUMPER AUX 1
MOH - ZONE 1 INPUT SOURCE
DEFAULT JUMPER SETTING
JUMPER AUX 1
5
3
SW701
DMS3120 MOH 01
Fig. 24 - Rear Panel View - ZONE 1 - ZONE 2 - MOH Outputs - Source Selectors and Controls
ZONE 1 MOH AND 8 OHM OUTPUTS
ZONE 1 OUTPUTS
The DMS Amplifier is equipped with two 1 Watt, 8 ohm Amplifiers
and a separate 600 ohm MUSIC ON HOLD AMPLIFIER.
MOH - ZONE1 & 2 AMPLIFIER FUNCTIONS
MOH AMPLIFIER
a) The MOH Amplifier can receive programs from AUX
1 - AUX 2 and the MODULE.
600 Ohm MOH - The MOH Output provides a 600 ohm, 1 Volt
Transformer Balanced Output (Reference 3).
b) Selection of the input source is by Internal Jumper.
1 WATT, 8 Ohm - Simultaneously a Second Zone 8 ohm, 1 Watt
Output may be utilized to drive up to 4 Speakers (Reference 4).
Outputs may be used simultaneously.
OUTPUT LEVEL CONTROL - A Level Control for both the 600
ohm Output and the 1 Watt Output is provided (Reference 2)
e) The Rear Panel ZONE 1 Level Control operates both
MOH AND 8 Ohm AMPLIFIER INPUT SOURCE SELECTION
The program source for the Input of the 600 ohm MOH Output and
the 8 ohm Output can be selected from either AUX 1 - AUX 2 or
the MODULE source. Set the Jumpers Set No. SW 702 to desired
position. Default setting is AUX 1.
c) The ZONE 1 independent 600 Ohm and 8 Ohm
d) The MOH 600 ohm Output is Transformer Balanced.
the 600 Ohm and 8 Ohm Outputs simultaneously.
MOH AND ZONE 1-2 OPERATION ISSUES
1) Paging from the Microphone Inputs or the Telephone
Input does not effect the MOH/ZONE 1-2 Amplifier.
ZONE 2 OUTPUT
1 WATT, 8 Ohm - A Second Zone 8 ohm, 1 Watt Output may be
utilized to drive up to 4 Speakers (Reference 5).
2) Position of the INPUTS Level Control does not affect the
OUTPUT LEVEL CONTROL - A Level Control for the 1 Watt
Output is provided (Reference 6)
affect the MOH/ZONE 1-2 Amplifier Output Level.
ZONE 2 - 8 Ohm AMPLIFIER INPUT SOURCE SELECTION
The program source for the Input the 8 ohm Output can be selected from either AUX 1 - AUX 2 or the MODULE source. Set the
Jumpers Set No. SW 701 to desired position. Default setting is
AUX 1.
Telephone) does not effect the Output of the MOH/ZONE 1-
PAGE 24
MOH/ZONE 1-2 Amplifier Output Level.
3) Position of the AUX 1 and AUX 2 ATTENUATOR does not
4) Muting activation of M1 or M2 Buss (from Microphones or
2 Amplifier except if the INPUT SOURCE is set to MODULE
and the Module Output is Muted. See Module Settings.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
MOH CONNECTIONS
3
600 ohm MOH System
MOH
Input
600
Ohm
4
Telephone
AWG 18 TWISTED PAIR
Telephone System
KSU
2
600
0
0
8
MOH OUT 1 WATT
ZONE 2
LEVEL
8
1 WATT
BALANCED
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC AMPLIFIER
117V 500W MAX
UNSWITCHED
COM
8
25V
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
70V
GROUND
VOX-1
SENS
AUX 2
0
JUMPER AUX 1
ZONE 2
ZONE 1
ZONE 1
LEVEL
MOH - ZONE 1
INPUT SOURCE
DEFAULT JUMPER
SETTING
MODULE
CAUTION: TO REDUCE THE
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE
FUSE.
SW702
117V 60HZ
SPEAKER OUTPUT
CLASS 2 WIRING ACCEPTABLE
LINE FUSE
5A 250V
SER. NO.
3120 MOH Zone 1
MOH OTPUT LEVEL CONTROL
Fig. 25 - Rear Panel MOH Connection Diagram
MUSIC ON HOLD AMPLIFIER
MOH AMPLIFIER
An independent 600 ohm, 1 Volt Output, Transformer Balanced
MUSIC-ON-HOLD Amplifier is provided. The Input SOURCE of the
MOH Amplifier can be selected from either the AUX 1 - AUX 2 or MODULE.
MOH - 600 OHM SYSTEM
Most Phone systems operate on a 600 ohm Input Impedance, if the
Impedance required is 600 ohm connect the Amplifier to the Phone
System MOH by using the diagram above (Reference 3).
MOH - 8 OHM, 1 WATT SYSTEM
Some older Key Phone systems require a 1 watt Power Output having
an Output Impedance of 8 ohm to drive the Music on Hold feature. If
the Impedance required is 8 ohm connect the Phone system MOH to
the 8 ohm, 1 Watt MOH Output of the Amplifier (Reference 4).
CABLE
Use a cable consisting of a twisted pair of at least AWG 18. Use care
in extending the cable and avoid routing near power lines, fluorescent
lights and other systems that may generate a disturbing electric field.
SOURCE SELECTOR
Select the Input Source desired by following the instructions at right.
CAUTION: REMOVAL OF THE COVER PRESENTS AN ELECTRICAL SHOCK HAZARD !
DMS3040/3080/3120
LEVEL CONTROL
After the wiring is completed adjust the MOH/ZONE 1
Amplifier Level Control on the rear panel to the desired output
level (Reference 2).
MOH/ZONE 1 AMPLIFIER SOURCE SELECTOR
MOH/ZONE 1 SOURCE SELECTOR
The Source for the MOH/ZONE 1 Amplifier can be selected
from either the AUX 1 - AUX 2 or MODULE by setting the
JUMPER SET No. SW702 provided for this purpose. Default
Setting for this Jumper Set is AUX 1. To change the setting do
the following:
ACCESS TO THE MOH/ZONE 1 INPUT SOURCE SETTING
1) Remove Power Cord from AC Outlet.
2) Remove the three screws on each side of the amplifier
holding the amplifier cover.
3) Lift Cover and locate the Jumpers Set No SW702 on the
MOH Amplifier Board (see Function Switches Jumpers
Location Diagram).
4) Set Jumper as required (AUX 1 - AUX 2 or MODULE)
5) Replace protective cover.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 25
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
USING SPEAKERS FOR ZONE 1 - ZONE 2
8
OHM
8
OHM
ZONE 1
MOH - ZONE 1
INPUT SOURCE
DEFAULT JUMPER
SETTING
ZONE 2
Up to Four 8 ohm Speakers may
be Connected
1/4W
5
4
2
CAUTION: TO REDUCE THE
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE
FUSE.
Up to Four 8 ohm Speakers may
be Connected
0
600
0
0
8
AUX 2
8
OHM
8
OHM
8
OHM
ZONE 2
INPUT SOURCE
DEFAULT JUMPER
SETTING
1 WATT
BALANCED
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC AMPLIFIER
117V 500W MAX
UNSWITCHED
COM
8
25V
70V
GROUND
1/4W
1/4W
6
ZONE 2
LEVEL
8
1/4W
8
OHM
ZONE 2
ZONE 1
ZONE 1
LEVEL
MOH OUT 1 WATT
JUMPER AUX 1
MODULE
AWG 18
TWISTED PAIR
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
VOX-1
SENS
AUX 2
8
OHM
AWG 18
TWISTED PAIR
JUMPER AUX 1
8
OHM
1/4W
1/4W
4 Speaker System Max. Power Output= 1/4W Each
1/4W
MODULE
1/4W
SW701
SW702
117V 60HZ
LINE FUSE
5A 250V
SPEAKER OUTPUT
CLASS 2 WIRING ACCEPTABLE
SER. NO.
3120 Zone 1&2
ZONE 1 OUTPUT LEVEL CONTROL
ZONE 2 OUTPUT LEVEL CONTROL
Fig. 26 - Rear Panel Zone 1 and 2 Speaker Connection Diagram
ZONE 1 AND 2 OPERATION
ZONE 1 AND 2 SETTINGS
ZONE 1 AND 2 OPERATION
The Amplifier is equipped with two independent 1 Watt, 8
ohm Outputs designated ZONE 1 (Reference 4) and ZONE
2 (Reference 5). The Outputs may be utilized to power up to
4 speakers in various combinations as described in the diagrams on the next page. This feature will provide a SECOND and THIRD ZONE (in addition to the main output) with
up to 1 Watt of output power and will amplify only the
Source from either AUX 1 - AUX 2 or MODULE (see input
source selection) and will not be affected by the Paging
(from MIC or TEL), VOX or MUTING.
INPUT SOURCE SELECTOR
Independent JUMPER SETS for ZONE 1 (SW702) and
ZONE 2 (SW701) are available to select the Input Source
for the two 1 Watt Amplifiers.
It can be used in any area (up to 1 Watt) where only a
Program Source is desired uninterrupted by Paging.
CABLE
Use an AWG 18 jacketed, twisted pair cable.
PAGE 26
DUAL PROGRAM SOURCE CAPABILITY
If desired separate program Sources may be used for
ZONE 1 and ZONE 2.
EXAMPLE: Use the program source from AUX 1 for ZONE
2 and the program source from AUX 2 for ZONE 2.
Select the Input Source desired by following the instructions
in the MOH Amplifier Source Selection section.
LEVEL CONTROL
After the wiring is completed adjust the ZONE 1 (Reference
2) and ZONE 2 (Reference 6) Level Controls on the rear
panel to the desired output level.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
ZONE 1 - ZONE 2 CONNECTING SPEAKERS
Zone 1
Zone 2
8 Ohm
8 Ohm
-
+
-
ZONE 2
ZONE 1
ZONE 1
LEVEL
0
600
USING A SINGLE 8 OHM SPEAKER WIRING
+
Max. Power Output
1 Watt
0
8
0
ZONE 2
LEVEL
8
USING A SINGLE 8 OHM SPEAKER PER ZONE
A single 8 ohm Speaker may be used connected to the
ZONE 1 and ZONE 2 1 Watt Output. In this configuration up
to 1 Watt of Power will be available on each Speaker.
Independent Level Controls are provided.
MOH OUT 1 WATT
BALANCED
1 WATT
3120 MOHspk01
Fig 27 - Using one 8 ohm Speaker
Zone 1
4 ohm
½W
¼W
When using two
4 Ohm Speakers
the maximum
Output Power to
each Speaker is
½ Watt
-
+
-
+
¼W
+
+
-
8 Ohm
8 Ohm
½W
-
USING TWO 4 OR 8 OHM SPEAKERS WIRING
Zone 2
4 ohm
When using two 8 Ohm
Speakers the maximum
Output Power to each
Speaker is ¼ Watt
ZONE 2
ZONE 1
ZONE 1
LEVEL
0
600
USING TWO 4 OR 8 OHM SPEAKERS
The Figure at left shows:
ZONE 1 with two 4 ohm speakers connected in series, each
speaker provides ½ Watt power output (1 Watt Total).
0
0
8
MOH OUT 1 WATT
BALANCED
ZONE 2
LEVEL
8
ZONE 2 with two 8 ohm speakers connected in series, each
speaker provides ¼ Watt power output (½ Watt Total).
Independent Level Controls are provided.
1 WATT
3120 Mohspk02
Fig 27A - Using two 4 or 8 ohm Speakers
USING FOUR 8 OHM SPEAKERS WIRING
Maximum Output
Power to each
Zone 1
Speaker is
8 ohm
8 ohm
¼ Watt
8 ohm
8 ohm
8 ohm
8 ohm
¼W
-
0
600
0
+
-
0
8
USING FOUR 8 OHM SPEAKERS PER ZONE
Four 8 ohm Speakers are used and connected to the 1 Watt
Output. In this configuration up to 1/4 Watt of Power will be
available on each Speaker (1 Watt Total).
Independent Level Controls are provided.
ZONE 2
8
MOH OUT 1 WATT
BALANCED
8 ohm
¼W
-
ZONE 1
ZONE 1
LEVEL
-
¼W
+
+
¼W
-
¼W
-
+
-
+
+
-
8 ohm
¼W
+
¼W
+
¼W
Zone 2
ZONE 2
LEVEL
1 WATT
3120 Mohspk03
Fig 27B - Using four 8 ohm Speakers
DMS3040/3080/3120
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 27
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
REGULATED AUXILIARY POWER SUPPLY
24 VOLT POWER SUPPLY
POWER SUPPLY
The Amplifier provides a 24 Volt - 250 mA DC Regulated
Auxiliary Power Supply Output (Reference 8).
8
MUTE 2
+
NO
-
G
M2
CABLE
To connect the Power Supply Output to accessories use a
two conductor wire not less than AWG 18. This minimum
wire gauge is necessary to minimize potential Voltage
Drops in long wire connection applications. For wire resistance refer to Table below.
MUTE 1
GROUND
C
MIC1
24V DC
250 mA
VOX RELAY
NC
UNMUTE
3120 Power Supply Output
MASTER
REMOTE
VOLUME
M1 RVC RVC C
Fig. 28 - 24 Volt Power Supply Output Diagram
WIRE GAUGE - RESISTANCE TABLE
WIRE
AWG
RESISTANCE IN
OHMS per 1000 Ft.
16
18
20
22
24
26
4.016
6.385
10.15
16.14
25.67
40.81
NOTE:
When calculating the Wire Resistance for each run
using a two conductor Wire the wire Resistance
should be doubled.
EXAMPLE: The Total Resistance of a 1000 Ft. run
of a AWG 24 two conductor Wire is:
25.67 X 2= 51.34 Ohm
VOX RELAY
A
VOX RELAY
VOX NOT ACTIVATED
Q237
MUTE 1 BUSS ON
M1
VOX RELAY FUNCTIONS
+
RL201
NO
JUMPER
M2
MUTE 2 BUSS OFF SW206
X
COM
D211
SWITCHSET SW206 DEFAULT SETTING
NC
VOX RELAY
VOX ACTIVATED
Q237
MUTE 1 BUSS ON
M1
+
B
RL201
The Relay can be configured to activate when either VOX
1 (M1) or VOX 2 (M2) or both (VOX 1 and VOX 2) are activated.
NO
JUMPER
M2
MUTE 2 BUSS OFF SW206
VOX RELAY
The Amplifier provides a VOX RELAY (Reference 7) with a
single pole dual throw set of contacts. Figure A at left
shows the contacts when the Relay is not activated. Figure
B shows the contacts when the Relay is activated.
X
The VOX RELAY will remain engaged for as long as the
VOX is active.
COM
D211
NC
SWITCHSET SW206 - The SW206 is defaulted to M1.
When VOX 1 is activated the Relay is switched ON. The
factory setting can be changed to set the Relay to activate
with either VOX 1 - VOX 2 or both.
C
NO
+
-
MIC1
G
M2
MUTE 1
MUTE 2
NC
24V DC
250 mA
GROUND
VOX RELAY
UNMUTE
7
MASTER
REMOTE
VOLUME
M1 RVC RVC C
Both Jumpers (M1 - M2) may be installed.
RELAY CONTACTS RATING
3120 Vox relay 01
7 AMPERE AT 30 VDC MAXIMUM RATING.
Fig. 28A - VOX Relay Output Terminals
PAGE 28
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
INSTALLATION AND WIRING
INSTALLING AND USING A BOSE® EQUALIZER MODULE
CAUTION: PRIOR TO INSTALLING THE BOSE® MODULE IN THE AMPLIFIER FOLLOW THE INSTRUCTIONS SUPPLIED WITH
THE MODULE AND THEN READ THE INSTRUCTIONS IN THIS MANUAL’S “INSTALLING A MODULE” SECTION
SET TONE BYPASS
SWITCH TO ON
METHOD 1
Equalize
Music Only
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
US 30TJ
PRE
OUT
SUB OUT
PRE EQ
Connect to
Module
EQ OUT
Connect to INPUT 4/AUX 1
INPUT-4(AUX1)
47kohm 100mV
MIX
BUSS
INPUT-5(AUX2)
47kohm 100mV
L
(AUX1)
ATTENUATOR
EQ LINK
(AUX2)
ATTENUATOR
EQ
OUT
AUDIO
L
R
IN
OUT
EQ LINK
OFF
ON
POWER SUB OUT LINE OUT TONE
600
IN
POST EQ
BYPASS
WARNING: THIS APPLIANCE
MUST BE EARTHED
INPUT 2 (MIC)
G COM HOT
INPUT 3 (MIC)
G COM HOT
INPUT 4 (MIC)
G
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
COM HOT RVC RVC
G COM HOT
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
TEL
G COM HOT
TEL OUTPUT
LEVEL
IN
R
METHOD 1
EQUALIZING THE PROGRAM ONLY
BY USING THIS METHOD THE
MUSIC PROGRAM ONLY IS EQUALIZED BY THE MODULE.
BE SURE THAT THE TONE BYPASS
SWITCH IS IN THE ON POSITION
1) Connect the Output of the PROGRAM SOURCE unit to the Module
IN Jack.
2) Connect the EQ. OUT Jack of the
Module to INPUT 4/AUX 1 of the
Amplifier.
102 EQ. MODULE
250ohm 1.5mV
BALANCED
600 ohm 100mV
MUSIC OUTPUT
BOSE MODULE METHOD 01
SATELLITE RECEIVER
TRACK
01
Connect Music
Source Output
to Module EQ IN
CD PLAYER
Fig. 26 - Method 1 Module Wiring Diagram
LEVEL CONTROLS - Adjust INPUT
4/AUX 1 Front Panel Control to 1
o'clock. Turn Rear Panel ATTENUATOR Control slowly clockwise until the
desired Output Level is achieved After
above adjustments are completed use
the INPUT 4/AUX 1 Front Panel
Control to increase or decrease the
Music Level as desired.
METHOD 2
USING THE EQ LINK
BY USING THIS METHOD ALL THE
AMPLIFIER INPUTS ARE EQUALIZED BY THE MODULE.
BE SURE THAT THE TONE BYPASS
SWITCH IS IN THE ON POSITION
1) Connect the Output of the PROGRAM SOURCE unit to the INPUT 4
(or INPUT 2) L and R Jacks.
2) Connect the EQ. OUT Jack of the
Module to the POWER IN Jack of the
Amplifier.
3) Connect the EQ. IN Jack of the
Module to the PREAMP. OUT Jack of
the Amplifier.
4) Set EQ LINK Switch on the
Amplifier to IN.
Fig. 26B - Method 2 Module Wiring Diagram
BOSE® is a Registered Trademark of BOSE Corporation
DMS3040/3080/3120
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
LEVEL CONTROLS - Adjust INPUT
4/AUX 1 Front Panel Control to 1
o'clock. Turn Rear Panel ATTENUATOR Control slowly clockwise until the
desired Output Level is achieved After
above adjustments are completed use
the INPUT 4/AUX 1 Front Panel
Control to increase or decrease the
Music Level as desired.
PAGE 29
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
JUMPER VOX 1 ON
JUMPER VOX 2 ON
SW214
V2
VOX JUMPERS
V1
OFF
KSU
RING
TIP
MIC
LO Z
JUMPER VOX 2 ON
V2
SW215
JUMPER VOX 1 ON
V1
SHIELD
b50side
Push to Talk Key
OFF
JUKEBOX REMOTE VOLUME CONTROL
A Jukebox Remote Volume Control may be provided to adjust the
Output Level independently from the Background Music Source.
The Jukebox Music Level should be set in accordance to the ambient noise which may change during peak business hours. The AUX
1 Input (used for the Jukebox) is equipped with a Remote Volume
Control Feature. Use the optional PASO Model RVC10W (10K)
Volume Control mounted on a single gang plate.
MUSIC ON HOLD
The Zone 1 Amplifier provides a separate 600 ohm Transformer
Balanced Music on Hold Output for the Telephone system. If the
Zone 1 Input Selector Switch is set to Input 3, the MOH Output
receives only the PROGRAM from the the MUSIC SOURCE without Paging or the Jukebox interruptions.
25V/70V Speaker
VOX JUMPERS
INPUT 1 (MIC 1) SETTINGS
PAGING FROM THE PHONE SYSTEM
PRIORITY PAGING FROM THE PHONE SYSTEM - Paging may
be generated from a Phone System by using the TEL INPUT of the
Amplifier. The TEL INPUT can be set to provide Priority Paging
over both the Music Program and the Jukebox if activated. The TEL
INPUT provides a 600 ohm Transformer balanced Phone interface.
MUTE 2 DELAY
The Jukebox Configuration utilizes the VOX/MUTE 2 Buss. In order
to prevent the premature JUKEBOX/MUSIC SOURCE switching
(the Music Source cuts-in while the Jukebox is active) a MUTE 2
DELAY TRIMMER is available on the Rear panel to increase the
MUTE 2 DELAY as necessary. The MUTE 2 DELAY can be adjusted from 3 to 30 Seconds.
EXAMPLE: If the Jukebox is playing and the Tune has a long pause
or the long pause while the Jukebox is cycling between CD’s it is
possible that the Music Source (Background Music) may cut-in
causing annoying and unwanted chatter while the Jukebox is still
active. To prevent this problem the MUTE 2 TIME DELAY should be
adjusted accordingly.
JUKEBOX
REMOTE
VOLUME
INPUT 4
REMOTE
VOLUME
PAGING MICROPHONE
25V/70V Speaker
ZONE 1 & 2 ONE WATT - 8 OHM OUTPUT
The ZONE 1 and ZONE 2 Outputs may be used to cover small
area with MUSIC ONLY without interruption from the Microphone
or Phone Paging or the music from the Jukebox. The Program
Source for both 1 Watt Amplifiers may be independently selected
through Internal Jumpers (see Diagram). Output Level may be also
independently adjusted by the separate Level Controls.
DMS JUKEBOX APP 121
25V/70V Speaker
DMS AP121
PAGING MICROPHONE
PRIORITY PAGING MICROPHONE - A Low Impedance Dynamic
Microphone can be connected to the Amplifier INPUT 1. The
Microphone Input can be set to provide Priority Paging over both
the Music Program and the Jukebox if activated. Optionally Paging
may be generated from the Phone system if desired.
OPTIONAL
PASO RVC10W
PHONE HAS
PRIORITY OVER
MUSIC
AND JUKEBOX
600 ohm 100mV
250ohm 1.5mV
BALANCED
MICROPHONE HAS
PRIORITY OVER
MUSIC SOURCE
AND JUKEBOX
SER. NO.
SPEAKER OUTPUT
LINE FUSE
5A 250V
GROUND
117V 60HZ
117V 500W MAX
UNSWITCHED
DMS3120rear
1 WATT
MOH OUT 1 WATT
APPLICATION
This
Note
illustrates
a
typical
installation
in
a
Restaurant/Diner/Lounge using Background Music and a Jukebox.
The Background Music can be automatically interrupted when the
Jukebox is activated. The Background Music is then automatically
restored once the Jukebox stops playing. This built-in feature of the
DMS Amplifier eliminates the need of any external device.
Phone Paging
TEL OUTPUT
LEVEL
TEL
G COM HOT
G COM HOT
COM HOT RVC RVC
G
G COM HOT
VOX-1
SENS
VOX-2
SENS
MUTE-2
DELAY
G COM HOT
G COM HOT
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
INPUT 4 (MIC)
INPUT 3 (MIC)
INPUT 2 (MIC)
INPUT 1 (MIC)
WARNING: THIS APPLIANCE
MUST BE EARTHED
120 W RMS
117V 60 HZ
850 VA
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
DIGITAL MUSIC AMPLIFIER
DMS3120
PROFESSIONAL AUDIO & SOUND
NO
C
TEL INPUT SETTINGS
CAUTION: REMOVE
POWER CORD FROM
AC OUTLET PRIOR TO
INSTALLING MODULE
PORT ACCEPTS
STANDARD
MODULE
OFF
ON
POWER SUB OUT LINE OUT TONE
600
IN
POST EQ
BYPASS
OUT
EQ LINK
IN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
(AUX1)
ATTENUATOR
EQ LINK
NC
8
0
LEVEL
MUSIC ON HOLD OUTPUT
CAUTION: TO REDUCE THE ATTENTION: AFIN DE REDUIRE LE RISQUE
D'INCENDIE REMPLACER SEUL PAR UN
RISK OF FIRE, REPLACE
ZONE 1
FUSIBLE DE MEME TYPE.
ONLY WITH SAME TYPE
FUSE.
ZONE 1
0
600
600 ohm MOH System
MOH
Input
600
Ohm
MUSIC ON HOLD
RECEIVES MUSIC
ONLY - NO PAGING
NO JUKEBOX
SW702
Telephone
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
L
INPUT-5(AUX2)
47kohm 100mV
MIX
BUSS
SUB OUT
PRE EQ
PRE
OUT
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
30TJ
US
MASTER
REMOTE
VOLUME
M1 RVC RVC C
M2
G
MIC1
-
24V DC
250 mA
+
VOX RELAY
ZONE 2
LEVEL
8
SW701
ZONE 2 SOURCE SETTING
8
OHM
Up to Four 8 ohm
Speakers may be
connected
8
OHM
ZONE 2
0
ZONE 2 LEVEL CONTROL
ADJUSTS OUTPUT
LEVEL OF ZONE 2
SPEAKERS
1/4W
1/4W
8
OHM
8
OHM
ZONE 2
LEVEL
MIC 4
1/4W
1/4W
JUMPER
AUX 2
AUX 1
MOD
ZONE 1 MOH SETTING
R
(AUX2)
ATTENUATOR
R
L
MUTE-2
DELAY
3 to 30 Sec
MUTE 2 DELAY CONTROL
ADJUSTS JUKEBOX MUTING
TIME OVER MUSIC SOURCE
INPUT
SW212
JUMPER
VOX 2 ON
JUKEBOX
AUTOMATICALLY
MUTES THE
MUSIC SOURCE
WHEN SWITCHED
ON
SW217
MUTE 1 ON
JUMPER
M1
V1
M2
OFF
VOX JUMPERS
MUTE JUMPERS
JUKEBOX
R
L
INPUT-4(AUX1)
47kohm 100mV
SW208 and SW229
MIC 5
AUX 2
MUSIC
SOURCE
SW213
SATELLITE RECEIVER
SW223
MOD
OFF
AUX 1
SW228
AUX 1
INPUT 4 (AUX 1) SETTINGS
V2
AUX 2
ZONE 2
JUMPER
OPTIONAL MUSIC
ONLY ZONE
GROUND
UNMUTE
AUX 1 - MIC 4 SWITCH
MUTE 1
MUTE 2
Telephone System
KSU
PAGE 30
BALANCED
ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE
CAUTION: TO REDUCE THE RISK OF FIRE OR OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE
SHOCK DO NOT EXPOSE THIS APPLIANCE TO OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN
RAIN OR MOISTURE. DO NOT REMOVE COVER. REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER
THERE ARE NO USER SERVICEABLE PARTS UNE PERSONNE QUALIFIEE
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
COM 8
25V 70V
MUTE 1 ON
MUTE 2 ON
JUMPER
JUMPER
VOX 2 OFF M2
V2
MUTE JUMPERS
OFF
VOX 1 OFF M1
JUMPER
VOX JUMPERS
V1
OFF
AUX 2 - MIC 5 SWITCH
INPUT 5 (AUX 2) SETTINGS
RESTAURANT/DINER WITH MUSIC AND JUKEBOX - APP. DATA 121
ZONE 1 AND 2 SPEAKERS
The Wiring Diagram shows the connection of up to 4 (8 ohm)
Speakers for the Zone 1 & 2 - 1 Watt Amplifier. When 4 Speakers
are used each Speaker Output will be a 1/4 Watt.
INPUT JUMPERS - SWITCHES SETTING
The Diagram indicates the various Input Settings for this application. Some settings may be already “Defaulted” when the Amplifier
is shipped and do not need re-setting.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DMS3040/3080/3120
MOD
SW702
JUMPER
AUX 2
MUSIC ON HOLD OUTPUT
600 ohm MOH System
1/4W
8
OHM
8
OHM
MUSIC ON HOLD
RECEIVES MUSIC
ONLY - NO PAGING
NO MESSAGE REPEATER
1/4W
8
OHM
8
OHM
ZONE 1
LEVEL
0
PASO
C55DMSTW - White
Waterproof Speaker
117V 60HZ
1 WATT
8
8
OHM
8
OHM
ZONE 2 SOURCE SETTING
Up to Four 8 ohm
Speakers may be
connected
ZONE 2
OPTIONAL MUSIC
ONLY ZONE
ZONE 2
LEVEL
SW701
25V/70V Speaker
DMS3120rear
GROUND
25V/70V Speaker
DMS C-STORE APP 123
8
OHM
8
OHM
C
-
VOX-1
SENS
JUMPER VOX 1 ON
JUMPER VOX 2 ON
V2
SW215
V1
OFF
VOX JUMPERS
OUT
G COM HOT
G COM HOT
G COM HOT
SHIELD
b50side
Push to Talk Key
MIC
LO Z
SW217
SUB OUT
PRE EQ
MIX
BUSS
MESSAGE REPEATER
G
R
(AUX1)
ATTENUATOR
MESSAGE
REPEATER
REMOTE
VOLUME
INPUT 4
REMOTE
VOLUME
OPTIONAL
PASO RVC10W
TEL
SW213
TEL OUTPUT
LEVEL
INPUT 5
MIC-AUX2
BY INTERNAL
SWITCH
R
(AUX2)
ATTENUATOR
L
L
MUSIC
SOURCE
KSU
Phone Paging
RING
TIP
V2
V1
JUMPER
JUMPER
PORT ACCEPTS
STANDARD
MODULE
MUTE 2 ON
V2
V1
OFF
SW214
JUMPER VOX 2 ON
JUMPER VOX 1 ON
VOX JUMPERS
TEL INPUT SETTINGS
CAUTION: REMOVE
POWER CORD FROM
AC OUTLET PRIOR TO
INSTALLING MODULE
R
SW223
JUMPER
VOX 2 OFF M2
MUTE 1 ON
MUTE JUMPERS
OFF
VOX 1 OFF M1
SATELLITE RECEIVER
INPUT-5(AUX2)
47kohm 100mV
600 ohm 100mV
G COM HOT
PHONE HAS
PRIORITY OVER
MUSIC
AND MESSAGE
REPEATER
G COM HOT
MIC 5
SW208 and SW229
AUX 2
OFF
VOX JUMPERS
INPUT 5 (AUX 2) SETTINGS
AUX 2 - MIC 5 SWITCH
INPUT-4(AUX1)
47kohm 100mV
L
INPUT 4 AUX2
REMOTE 47Kohm 100 mV
VOLUME INPUT5 (MIC-AUX2)
COM HOT RVC RVC
INPUT 4 (MIC)
250ohm 1.5mV
BALANCED
INPUT 3 (MIC)
INPUT 2 (MIC)
PAGING MICROPHONE
PRE
OUT
M2
MUTE 1 ON
OFF
ON
POWER SUB OUT LINE OUT TONE
600
IN
POST EQ
BYPASS
INPUT 1 (MIC)
EQ LINK
IN
EQ LINK
LISTED
COMMERCIAL
AUDIO
EQUIPMENT
US 30TJ
MUTE-2
DELAY
3 to 30 Sec
VOX 2 ON
JUMPER
MESSAGES MUTE
MUSIC AT THE PUMPS
SW212
JUMPER
M1
V2
V1
PASO MODEL B500X MICROPHONE
MICROPHONE HAS
PRIORITY OVER
SATELLITE RECEIVER
AND MESSAGE
REPEATER
MUTE-2
DELAY
INPUT 1 (MIC 1) SETTINGS
VOX-2
SENS
120 W RMS
117V 60 HZ
850 VA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
M2
MUTE 2 DELAY CONTROL
ADJUSTS MESSAGE
REPEATER MUTING TIME
OVER SATELLITE
RECEIVER
MASTER
REMOTE
VOLUME
M1 RVC RVC C
MIC 4
SW228
AUX 1
OFF
MUTE JUMPERS
OFF
VOX JUMPERS
INPUT 4 (AUX 1) SETTINGS
AUX 1 - MIC 4 SWITCH
WARNING: THIS APPLIANCE
MUST BE EARTHED
G
DMS3120
NO
+
MIC1
ZONE 2 LEVEL CONTROL
ADJUSTS OUTPUT
LEVEL OF ZONE 2
SPEAKERS
24V DC
250 mA
ZONE 2
LEVEL
1/4W
1/4W
DIGITAL MUSIC AMPLIFIER
PROFESSIONAL AUDIO & SOUND
NC
VOX RELAY
1/4W
1/4W
POWER RATING
SUPPLY VOLTAGE
POWER CONSUMPTION
SER. NO.
25V/70V Speaker
SPEAKER OUTPUT
GAS PUMP SPEAKERS - MUSIC/MESSAGES AND PAGING
LINE FUSE
5A 250V
117V 500W MAX
UNSWITCHED
MOH OUT 1 WATT
0
ZONE 2
CEILING SPEAKERS MOUNTED INSIDE C-STORE
The Amplifier provides two independent 1 Watt-8 Ohm Outputs.
Up to 4-8 ohm Speakers may be connected to each Output.
The use of both Outputs is optional follow the
individual requirement.
BALANCED
ATTENTION: POUR REDUIRLES RISQUES D' INCENDIE
CAUTION: TO REDUCE THE RISK OF FIRE OR OU DE CHOC ELECTRIQUE, NE PAS EXPOSER A LA PLUIE
SHOCK DO NOT EXPOSE THIS APPLIANCE TO OU L' HUMIDITE, NE PAS ENLEVER LE COUVERCLE. AUCUN
RAIN OR MOISTURE. DO NOT REMOVE COVER. REGLAGE A L' INTERIEUR. POUR REPARATION CONSULTER
THERE ARE NO USER SERVICEABLE PARTS UNE PERSONNE QUALIFIEE
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
COM 8
25V 70V
LEVEL
8
AWG 18
TWISTED PAIR
CAUTION: TO REDUCE THE ATTENTION: AFIN DE REDUIRE LE RISQUE
D'INCENDIE REMPLACER SEUL PAR UN
RISK OF FIRE, REPLACE
ZONE 1
FUSIBLE DE MEME TYPE.
ONLY WITH SAME TYPE
FUSE.
ZONE 1
0
600
MOH
Input
600
Ohm
Telephone
ZONE 1 MOH SETTING
1/4W
MOD
AUX 1
Telephone System
KSU
CEILING SPEAKERS MOUNTED INSIDE C-STORE RECEIVE MUSIC ONLY - NO MESSAGES OR PAGING
AUX 1
1/4W
AUX 2
JUMPER
ZONE 1
GROUND
UNMUTE
OPTIONAL MUSIC
ONLY ZONE
MUTE 1
DMS3040/3080/3120
MUTE 2
®
DIGITAL MUSIC AMPLIFIERS
TM
PROFESSIONAL AUDIO & SOUND
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
DIGITAL MUSIC SERIES
AUTO SERVICE STATION C - STORE - APP. DATA 123
APPLICATION
This Note illustrates a typical Auto Service Station
C-Store application. The size of the Service
Station and the number of Gas Pump Islands to
cover will determine the amount of outdoor
Waterproof Speakers required and the Power
Output of the Amplifier.
GAS PUMP OUTDOOR SPEAKERS
40 WATT SYSTEM EXAMPLE - The PASO Model
C55DMST Waterproof Music Speaker is recommended. Typically each Speaker should be tapped
at 5 Watt. In this configuration up to 8 Speaker
may be used with the Model DMS3040 40 Watt
Amplifier for distribution of Music and Messages
at the Gas Pumps.
For larger systems use a higher power Amplifier
and the additional quantity of speakers required.
C _ STORE INDOOR SPEAKERS
The Amplifier is equipped with two independent 1
Watt , 8 ohm Amplifiers = ZONE 1 and ZONE 2.
C-STORE - Up to 4+4 Ceiling Speakers may be
utilized indoors in the Store area, Rest Rooms or
other area such as a separate concession. By utilizing the separate (2) 1 Watt Amplifiers as a first
and second zone, only the Music program will be
distributed inside the Store. This avoids the continuous and annoying repeating of the messages
in the indoor areas. The output level may be
adjusted by the 1st and 2nd Zone Level Control.
ZONE 1 - ZONE 2 PROGRAM SOURCE SELECTOR
The program Source for each Zone Output may
be selected by setting the Zone 1 and 2 Jumper
Set to either AUX 1 - AUX 2 or Module Source.
MUSIC ON HOLD
The Zone 1 Amplifier provides a separate 600
ohm Transformer Balanced Music on Hold Output
for the Telephone system. If the Zone 1 Input
Select Jumper Set is set to AUX 1, the MOH
Output receives the Music from the Satellite
Receiver without Paging or Messages interruptions.
PAGING MICROPHONE
PRIORITY PAGING MICROPHONE - A Low
Impedance Dynamic Microphone can be connected to the Amplifier INPUT 1. The Microphone can
be set to provide Priority Paging over both the
Music Program and the Message Repeater.
Optionally Paging may be generated from the
Phone system if desired. The TEL INPUT provides
a 600 ohm Transformer balanced Phone interface.
MESSAGE REPEATER
The Message Repeater provides pre-recorded
Messages at the Gas Pumps Only. Each time a
message is initiated by the Repeater (AUX 1) the
Music (AUX 2) is automatically muted for the duration of the message.
REPEATER REMOTE VOLUME
A Master Remote Volume Control PASO Model
RVC10W may be provided to adjust the Output
Level of the Message Repeater in accordance to
the outdoors noise.
PAGE 31
®
TM
DIGITAL MUSIC AMPLIFIERS
DIGITAL MUSIC SERIES
PROFESSIONAL AUDIO & SOUND
CUSTOMER SERVICE
REPAIR SERVICE
REPLACEMENT PARTS
Please provide complete information when you request replacement parts from either the Factory or a Paso Authorized
Distributor. Be certain to include the Part Number and
Description as it appears on the parts list, the Model Number of
the unit and if possible the Serial Number and the date of purchase of the unit. Replacement parts inventory is maintained
specifically to repair Paso products. Part sales for other reasons
or applications will be declined.
REPAIR SERVICE
Repair service for out of warranty Paso products may be
obtained form your local Paso distributor or any other qualified
repair station.
ORDERING FROM THE FACTORY
Print all information on a purchase order form and mail to:
PASO SOUND PRODUCTS, INC.
4750 Goer Drive - Building F
CHARLESTON, SC 29406
IN WARRANTY REPAIR SERVICE
Call or write the Factory to obtain an authorization to return
the product for repairs.
Be sure to include the following:
- Paso part number
- Part description
- Quantity required
- Model number of the unit
- Serial number of the unit
- Your payment or your authorization for COD shipment for parts
not covered by the Warranty or if your company has a current
account with the factory
In warranty repairs must be returned to the Factory.
Prior authorization must be obtained from the Factory.
Products received without authorization will be refused by our
Receiving Dept..
Pack the equipment in the original carton or in a strong carton
with at least THREE INCHES of resilient packing material on all
sides, top and bottom. Seal the carton with reinforced tape and
mark it FRAGILE on at least two sides. Remember, the Carrier
will not accept liability for shipping damages if the unit is improperly packed.
EQUIPMENT RECEIVED IN DAMAGED CONDITION DUE TO
POOR PACKING WILL BE REFUSED AND THE WARRANTY
COVERAGE IS AUTOMATICALLY VOIDED.
The Paso Sound Limited Warranty provides:
RETAIN ORIGINAL IN WARRANTY PARTS UNTIL YOU
RECEIVE REPLACEMENTS. PARTS THAT SHOULD BE
RETURNED TO THE FACTORY WILL BE LISTED ON YOUR
PACKING SLIP.
For your convenience replacement parts are also available
through Paso Authorized Distributors and Dealers nation wide.
Obtain a location list directly from the Factory or your regional
Paso Representative.
Call or write for assistance. You will find our Technical Dept..
eager to help or assist you with any technical problem you may
have encountered except “`Customizing'' for a unique application.
Call our toll-free phone number:
Ship via insured prepaid United Parcel Service or Parcel Post to:
PASO SOUND PRODUCTS, INC.
4750 Goer Drive - Building F
CHARLESTON, SC 29406
Attn. SERVICE DEPARTMENT
The equipment will be returned freight prepaid after repairs.
TECHNICAL CONSULTATION
- Need help with your installation ?
- Need help with the operation of the unit ?
- Need help with a repair ?
The effectiveness of our consultation service depends on
the accuracy of the information you furnish.
Be sure to tell us:
- The Model and Serial number of the unit
- The date of purchase
- An exact description of the difficulty
- All you have done in attempting to correct the problem
The examination of the returned product must disclose in our
judgement, a manufacturing defect. The warranty does not
extend to any product that has been subject to misuse, neglect,
accident, improper installation or where the serial number of the
product has been removed or defaced.
Be sure to include the following:
- Your name and address
- Date of purchase and copy of invoice
- A brief description of the difficulty
- A return address shipping label
OUT OF WARRANTY REPAIR SERVICE
Follow return instructions as per in warranty repair service. Prior
to performing all necessary repairs, you will be advised of the
charges and at that time a written authorization by you will be
required including authorization to return the equipment COD for
the service and shipping charges. This will avoid unnecessary
delays in returning the equipment to you.
1-800 231 3034
Printed in USA
Manual OM 163
PAGE BACK
Download PDF

advertising