Emerson 00809-0100-4514 Satellite Radio User Manual

Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Alphaline® Nuclear Pressure Transmitter
www.rosemountnuclear.com
IMPORTANT NOTICE -- ERRATA
Model 1154 Product Manual 00809-0100-4514 Rev BA (January 2008)
1
Affected
Pages
6-6
2
3-5
No.
Description of Change
Process Flange –CF3M (Cast version of 316L SST)
Drain/Vent Valves –316L SST
Process Connections – 3/8-inch Swagelok compression fitting, 316L SST (1/4-18
NPT optional)
Change the last paragraph on the page to read as follows:
Effect.
Date
10/21/09
4/13/12
”Damping electronics are available as an option. Transmitters with standard
electronics can be retrofitted with the adjustable damping feature by changing out
both the amplifier board and the calibration board. Please reference Table 6-2
(Rosemount 1154DP, 1154HP, and 1154GP Spare Parts) for the applicable part
numbers.”
3
6-9
Table 6-2,”Rosemount 1154DP, 1154HP, and 1154GP Spare Parts”, in all locations
the following part numbers are updated:
4/13/12
Amplifier Circuit Board, Output Code R:
”01154-0001-0005” is replaced by ”01154-0153-0001”
Amplifier Circuit Board with Damping, Output Code R:
”01154-0021-0004” is replaced by ”01154-0156-0001”
Amplifier Circuit Board, Output Code R, N0026:
”01154-0001-0006” is replace by ”01154-0153-0002”
(5)
Sensor Module, 316 SST :
”01154-0300-0242” is replaced by ”01154-5300-0242”
0-25/150 inH2O:
”01154-0300-0342” is replaced by ”01154-5300-0342”
”01154-0300-0142” is replaced by ”01154-5300-0142”
0-125/750 inH2O: ”01154-0300-0252” is replaced by ”01154-5300-0252”
”01154-0300-0352” is replaced by ”01154-5300-0352”
”01154-0300-0152” is replaced by ”01154-5300-0152”
0-17/100 psi:
”01154-0300-0262” is replaced by ”01154-5300-0262”
”01154-0300-0362” is replaced by ”01154-5300-0362”
”01154-0300-0162” is replaced by ”01154-5300-0162”
0-50/300 psi:
”01154-0300-0272” is replaced by ”01154-5300-0272”
”01154-0300-0372” is replaced by ”01154-5300-0372”
”01154-0300-0172” is replaced by ”01154-5300-0172”
0-170/1,000 psi:
”01154-0300-0282” is replaced by ”01154-5300-0282”
”01154-0300-0182” is replaced by ”01154-5300-0182”
0-500/3,000 psi:
”01154-0300-0192” is replaced by ”01154-5300-0192”
0-1,000/4,000 psi: ”01154-0300-0102” is replaced by ”01154-5300-0102”
4
6-10
Table 6-2,” Rosemount 1154DP, 1154HP, and 1154GP Spare Parts”, the table
footnotes are updated to add note (5) which will read as follows:
(5) IMPORTANT NOTICE: To maintain a transmitter’s qualified configuration,
when purchasing or installing a new Sensor Module, Rosemount Qualification
report D2011019 must be carefully reviewed to verify that the Sensor Module
to be installed and the associated Amplifier Circuit Board in a given
transmitter is a qualified configuration. As detailed in the referenced report, not
all Sensor Module part numbers are considered qualified in conjunction with certain
Amplifier Circuit Boards.
4/13/12
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Rosemount 1154 Alphaline®
Nuclear Pressure Transmitter
NOTICE
Read this manual before working with the product. For personal and system safety and
optimum product performance make sure you thoroughly understand the contents before
installing, using, or maintaining this product.
For equipment service needs outside the United States, contact the nearest Rosemount
representative.
Within the United States, the North American Response Center is at your service 24 hours a
day, and is a single-point contact for all Rosemount equipment service needs. If at any time
you are not sure what to do, have a question about using the product, or have a service or
support request, call the center toll-free at 1-800-654-RSMT (7768). This contact is your
fastest link to quick and complete answers about any Rosemount Group product or service.
Alphaline, Rosemount and the Rosemount logotype are registered trademarks of Rosemount
Inc.
␦-Cell is a trademark of Rosemount Inc.
Loctite is a registered trademark of Henkel HGaA Corporation.
Swagelok is a registered trademark of Swagelok Company.
D.C. 55 is a registered trademark of Dow Corning Corporation.
Lubri-Bond is a registered trademark of E/M Corporation
Grafoil is a trademark of Union Carbide Corp.
Cover Photo: 1153-001AB
Rosemount Nuclear Instruments, Inc. satisfies all obligations coming from
legislation to harmonize product requirements in the European Union.
www.rosemountnuclear.com
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Rosemount Nuclear Instruments, Inc.
Warranty and Limitations of Remedy
The warranty and limitations of remedy applicable to this Rosemount
equipment are as stated on the reverse of the current Rosemount quotation
and customer acknowledgment forms.
RETURN OF MATERIAL
Authorization for return is required from Rosemount Nuclear Instruments, Inc. prior to
shipment. Contact the Nuclear Instruments Group (952-949-5210) for details on obtaining
“Returned Material Authorization (RMA)”. Rosemount Nuclear Instruments will not accept
any returned material without a Returned Material Authorization. Materials returned
without authorization are subject to return to customer.
Material returned for repair, whether in or out of warranty, should be shipped prepaid to:
Rosemount Nuclear Instruments, Inc.
8200 Market Blvd
Chanhassen, MN 55317
USA
IMPORTANT
The Rosemount 1154 Alphaline Pressure Transmitter is designed for nuclear use, has been
tested per IEEE Std 323-1974 and IEEE Std 344-1975 as defined in Rosemount Report
D8400102, and is manufactured to the requirements of NQA-1; 10CFR50, Appendix B
quality assurance programs; and 10CFR Part 21. During qualification testing, interfaces
were defined between the transmitter and its environment that are essential to meeting
IEEE Std 323-1974 requirements. To ensure compliance with 10CFR Part 21, the
transmitter must comply with the requirements herein throughout its installation, operation
and maintenance. It is incumbent upon the user to ensure that the Rosemount Nuclear
Instruments, Inc.’s component traceability program is continued throughout the qualified life
of the transmitter.
In order to maintain the qualified status of the transmitter, the essential environmental
interfaces must not be compromised. Performance of any operations on the transmitter
other than those specifically authorized in this manual may compromise an essential
environmental interface.
Where the manual uses the terms requirements, mandatory, must, or required, the
instructions so referenced must be carefully followed. Rosemount Nuclear Instruments, Inc.
expressly disclaims all responsibility and liability for transmitters for which the foregoing has
not been complied with by the user.
ii
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Revision Status
Changes From June 1999 to January 2008
Page (New)
Page (Old)
Cover
Inside Cover, i,
ii, 5-8 & Back
Cover
3-5, 6-8 & 6-9
Cover
ii, 5-9, 5-10 &
Back Cover
Throughout
i, back cover
3-5, 6-9 & 6-10
2-1,3-1,4-1,5-1,
6-1
2-2
Throughout
Cover, i, ii &
back cover
Cover, i, back
page
2-1,3-1,4-1,5-1,
6-1
2-2
2-2
2-4
2-4
2-6 & 2-7
5-7 & 6-9
6-1
6-9
-
2-3
2-4
2-5
2-6 & 2-7
5-8 & 6-10
6-2
6-10
Back Cover
-
Changes
Document revision dates changed from June 1999 to January 2008, rev from AA to BA.
Include errata sheet information on address and phone number.
Include errata sheet information on circuit board number changes:
• Replaced amplifier circuit card, output code R P/N 01154-0001-0001 with 01154-0001-0005.
• Replaced amplifier circuit card with damping, output code R P/N 01154-0021-0002 with
01154-0021-0004.
• Replaced amplifier circuit card, output code R, N0026 P/N 01154-0001-0002 with
01154-0001-0006.
References to Fisher-Rosemount were changed to Emerson Process Management.
Web address changed from www.rosemount.com to
www.rosemountnuclear.com.
Added reference to European Union product requirement (CE).
Added table of contents to each section
Removed the word “process” from sentence indicating user assumes responsibility for qualifying the
connection interface.
Updated reference to Swagelok catalog and added web address, removed street address.
Removed reference to 353C
Rearranged wording on shielded cable.
Added word “nominal” to Notes in drawings. Changed significant digits to conform to standard.
Inserted information on the spare parts kit for bolts and nuts for process flange.
Changed ISO 9001 to ISO 9001:2000
Replaced pipe mount bracket kit (adapters) P/N 01154-0038-0001 with P/N 01154-0044-0001
Added trademark & registration information
NOTE
The above Revision Status list summarizes the changes made. Please refer to both manuals for complete
comparison details.
www.rosemountnuclear.com
Reference Manual
Rosemount 1154
iv
00809-0100-4514, Rev BA
January 2008
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Table of Contents
SECTION 1
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
About The Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
SECTION 2
Installation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
General Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Process Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
SECTION 3
Calibration
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Span Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Zero Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Calibration Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Zero and Span Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Linearity Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Damping Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Correction For High Line Pressure
(Rosemount 1154DP and 1154HP Only) . . . . . . . . . . . . . . . . . . . . 3-6
Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
SECTION 4
Operation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Transmitter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
The δ-Cell™ Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Demodulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Linearity Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Zero and Span Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Current Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Reverse Polarity Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
www.rosemountnuclear.com
Reference Manual
Rosemount 1154
00809-0100-4514, Rev BA
January 2008
SECTION 5
Maintenance and
Troubleshooting
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Test Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Board Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Sensing Module Checkout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Disassembly Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Process Flange Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Electrical Housing Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Removing Sensor Module from Electrical Housing . . . . . . . . . . . . 5-6
Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Preliminary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Connecting the Electrical Housing to the Sensor Module . . . . . . . 5-7
Electrical Housing Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Process Flange Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Post Assembly Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
SECTION 6
Specifications and
Reference Data
Nuclear Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Radiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Seismic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Steam Pressure/Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Chemical Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Post DBE Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Quality Assurance Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Nuclear Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Hydrostatic Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Traceability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Qualified Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Dead Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Temperature Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Overpressure Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Static Pressure Zero Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Static Pressure Span Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Power Supply Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Load Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Mounting Position Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Span and Zero. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Zero Elevation and Suppression . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Temperature Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Humidity Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Volumetric Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Turn-on Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Pressure Ranges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Maximum Working Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Static Pressure and Overpressure Limits . . . . . . . . . . . . . . . . . 6-6
Overpressure Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
TOC-2
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Materials of Construction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Electrical Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Process Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Spare Parts Shelf Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
NOTES: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
TOC-3
Reference Manual
Rosemount 1154
TOC-4
00809-0100-4514, Rev BA
January 2008
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Section 1
Introduction
OVERVIEW
This manual is designed to assist in installing, operating, and maintaining the
Rosemount 1154 Pressure Transmitter. The manual is organized into the
following sections:
Section 2: Installation
Provides general, mechanical, and electrical installation considerations to
guide you through a safe and effective transmitter installation.
Section 3: Calibration
Provides transmitter calibration procedures.
Section 4: Operation
Provides descriptions of how the transmitter operates.
Section 5: Maintenance and Troubleshooting
Provides basic hardware troubleshooting considerations including sensing
module checkout, disassembly and reassembly procedures, and
post-assembly tests.
Section 6: Specifications and Reference Data
Provides nuclear, performance, functional, and physical transmitter
specifications; also includes ordering information, and a list of spare parts.
ABOUT THE
TRANSMITTER
Rosemount 1154 Pressure Transmitters are designed for precision pressure
measurements in nuclear applications requiring reliable performance and
safety over a specified qualified life. These transmitters were generically
tested to the IEEE Std 323-1974 and IEEE Std 344-1975 per the Qualification
Test Report D8400102. The Rosemount 1154 has been qualification tested to
environments typical of Pressurized Water Reactors (PWR) under accident
conditions. Stringent quality control during the manufacturing process
includes traceability of pressure retaining parts, special nuclear cleaning, and
hydrostatic testing.
Rosemount 1154 Transmitters are uniquely built to Class 1E nuclear service
while retaining the working concept and design parameters of the Rosemount
1151 Series that have become a standard of reliable service. Units are
available in gage (G), differential (D), and high-line differential (H)
configurations, with a variety of pressure range options, as shown in Table 6-1
on page 6-8. Figure 2-5 on page 2-7 shows dimensional drawings for the
transmitters.
www.rosemountnuclear.com
Reference Manual
Rosemount 1154
1-2
00809-0100-4514, Rev BA
January 2008
Reference Manual
00809-0100-4514, Rev BA
January 2008
Section 2
Rosemount 1154
Installation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
General Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-4
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-6
OVERVIEW
GENERAL
CONSIDERATIONS
www.rosemountnuclear.com
This section contains information and instructions regarding the following
installation-related information:
•
General Considerations
•
Mechanical Considerations
Process Connections
Conduit
•
Electrical Considerations
•
Installation Procedures
Mechanical
Electrical
The quality and accuracy of flow, level, or pressure measurement depends
largely on the proper installation of the transmitter and its associated impulse
piping and valves. For flow measurement, proper installation of the primary
measuring element is also critical to the accuracy of the measurement.
Transmitter installation should minimize the effects of temperature gradients
and temperature fluctuations, and avoid vibration and shock during normal
operation. Take care when designing the measurement to minimize the error
caused by incorrect installation. The ambient temperature of the transmitter
environment affects the qualified life of the transmitter (see Figure 2-1).
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 2-1. Qualified
Life vs. Ambient Temperature.
Time (Years)
Electronics
Qualified Life
Module
Qualified
Life
Temperature (°F)
MECHANICAL
CONSIDERATIONS
This section contains information you should consider when preparing to
mount the transmitter. Read this section carefully before proceeding to the
mechanical installation procedure.
Mount the Rosemount 1154 transmitter to a rigid support (a support with a
fundamental mechanical resonant frequency of 40 Hz or greater). A mounting
bracket included with the transmitter facilitates panel mounting. Figure 2-4 on
page 2-6 shows the qualified mounting configurations. The transmitter was
seismic qualified with the bracket mounted with four 3/8-in. diameter bolts.
Orientation with respect to gravity is not critical to qualification. However, if the
transmitter is mounted with the flanges in a horizontal position, zero the
transmitter to cancel the liquid head effect caused by the difference in height
of the process connections.
If the transmitter is mounted to a non-rigid panel, the user must ensure that
seismic input to the mounting bracket does not exceed qualification levels
given in Rosemount Report D8400102.
Process Connections
Process tubing installation must prevent any added mechanical stress on the
transmitter under seismic disturbances. This may be done by using
stress-relief loops in the process tubing or by separately supporting the
process tubing close to the transmitter.
The process connections to the transmitter flanges were qualified with 3/8-in.
tubing using Swagelok® compression fittings. For options using 1/4–18 NPT
connections, the user assumes responsibility for qualifying the interface.
The Swagelok tube fittings are shipped completely assembled for immediate
use. Do not disassemble them before use; doing so may contaminate the
fittings and result in leaks. Insert the tubing into the Swagelok tube fitting,
making sure that the tubing rests firmly on the shoulder of the fitting and that
the nut is finger tight. Tighten the nut one-and-one-quarter turns past finger
tight to prepare the transmitter for use. Do not overtighten.
2-2
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Transmitters with Flange Options A, D, H, J, L, or M are shipped with
Swagelok fittings for process connections. Included are front ferrule, rear
ferrule, and nut. Ensure that the fittings are placed on the tubing with the
orientation and relative position shown in Detail A, Figure 2-5 on page 2-7.
Process tubing used is 3/8-inch outside diameter, and of suitable thickness for
the pressure involved.
The connections can be loosened and re-tightened 20-30 times without
compromising the leak proof seal. To reconnect, insert the tubing with
pre-swaged ferrules into the fitting until the front ferrule sits in the fitting.
Tighten the nut by hand, then rotate one-quarter turn more or to the original
one-and-one-quarter tight position. Then snug the nut slightly with a wrench.
For more information regarding the use of Swagelok tube fittings, refer to:
Fittings Catalog MS-01-140
“Gaugable Tube Fittings and Adapter Fittings”
www.swagelok.com
If the drain/vent valves must be opened to bleed process lines, torque them to
7.5 ft-lb (10 N-m) when closing.
Proper location of the transmitter with respect to the process tubing depends
on various process parameters. When determining the best location, consider
the following:
•
Keep hot or corrosive fluids from contacting the transmitter.
•
Prevent sediment from depositing in the impulse tubing.
•
Ambient temperature gradients and fluctuations can result in erroneous
transmitter readings.
•
Keep impulse tubing as short as possible.
•
For differential transmitters, balance the liquid head on both legs of the
impulse tubing.
•
For liquid flow or pressure measurements, make taps on the side of the
line to avoid sediment deposits, and mount the transmitter beside or
below the taps so gases vent into the process line (see Figure 2-6 on
page 2-8).
•
For gas flow or pressure measurements, make taps on the top or side
of the line and mount the transmitter beside or above the taps so liquid
drains into the process line (see Figure 2-6 on page 2-8).
•
For steam flow or pressure measurements, make taps on the side of
the line, and mount the transmitter below the taps so the impulse tubing
stays filled with condensate (See Figure 2-6 on page 2-8).
•
For steam service, fill the lines with water to prevent steam from
contacting the transmitter. Condensate chambers are not necessary
since the volumetric displacement of the transmitter
is negligible.
2-3
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
The piping between the process and the transmitter must transfer the
pressure measured at the process taps to the transmitter. Possible sources of
error in this pressure transfer are:
•
Leaks
•
Friction loss (particularly if purging is used)
•
Trapped gas in a liquid line or trapped liquid in a gas line (head error)
•
Temperature-induced density variation between legs (head error), for
differential transmitters
To minimize the possibility of errors, take the following precautions:
•
Make impulse tubing as short as possible.
•
Slope tubing at least one inch per foot up toward the process
connections for liquid and steam.
•
Slope tubing at least one inch per foot down toward the process
connections for gas.
•
Avoid high points in liquid lines and low points in gas lines.
•
Use impulse tubing of sufficient diameter to avoid friction effects.
•
Ensure that all gas is vented from liquid tubing legs.
•
Ensure that impulse tubing is of adequate strength to be compatible
with anticipated pressures.
For differential transmitters, also consider the following:
•
Keep both impulse legs at the same temperature.
•
When using sealing fluid, fill both piping legs to the same level.
•
When purging, make the purge connection close to the process taps
and purge through equal lengths of the same size tubing. Avoid purging
through the transmitter.
Conduit
The conduit connection to the transmitter is 1/2–14 NPT. Use a qualified
conduit seal at the conduit entry to prevent moisture from accumulating in the
terminal side of the housing during accident conditions. To prevent the conduit
from adding mechanical stress to the transmitter during seismic disturbances,
use flexible conduit or support the conduit near the transmitter. Install the
conduit seal in accordance with the manufacturer’s instructions or use the
procedure on page 2-8.
ELECTRICAL
CONSIDERATIONS
This section contains information that you should consider when preparing to
make electrical connections to the transmitter. Read this section carefully
before proceeding to the electrical installation procedures.
The Rosemount 1154 pressure transmitter provides a 4–20 mA signal when
connected to a suitable dc power source. Figure 2-2 on page 2-5 shows a
typical signal loop consisting of transmitter, power supply, and various
receivers (controller, indicator, computer, etc.). The power supply must supply
at least 12 volts to the transmitter terminals at 30 mA (overscale) signal, or the
maximum output current required for proper system operation. Any power
supply ripple appears in the output load. The supply voltage versus load
limitation relationship is shown in Figure 2-3 on page 2-5. See qualification
report D8400102 for details. The load is the sum of the resistance of the
signal leads and the load resistance of the receivers.
2-4
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Signal wiring need not be shielded, but twisted pairs yield the best results. In
electrically noisy environments, shielded cable should be used for best
results. Do not run signal wiring in conduit or open trays with power wiring, or
near heavy electrical equipment. Signal wiring may be ungrounded (floating)
or grounded at any place in the signal loop. The transmitter case may be
grounded or ungrounded.
The capacitance-sensing element uses alternating current to generate a
capacitance signal. This alternating current is developed in an oscillator circuit
with a frequency of 32,000 ±10,000 Hz. This 32,000 Hz signal is capacitor
coupled to transmitter case ground through the sensing element. Because of
this coupling, a voltage may be imposed across the load, depending on
choice of grounding.
The impressed voltage, which is seen as high frequency noise, has no effect
on most instruments. Computers with short sampling times in a circuit where
the negative transmitter terminal is grounded will detect a significant noise
signal. Filter this noise with a large capacitor (1 µf) or by using a 32,000 Hz LC
filter across the load. Signal loops grounded at any other point are negligibly
affected by this noise and do not need filtering.
Figure 2-2. Transmitter Wiring
Connections.
Power
Supply
Terminal Side
Cover Removed
Figure 2-3. Supply Voltage vs.
Load.
4—20 mA DC
1825
Load Resistance (Ω)
1575
Qualified
Region
1500
1000
Design
Region
500
0
0
50
40
12
13.5
35
45
Power Supply (V DC)
2-5
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
INSTALLATION
PROCEDURES
Installation consists of mounting the transmitter and conduit and making
electrical connections. Procedures follow for each operation.
Mechanical
Transmitter
Be careful not to break the neck seal between the sensor module and the
electronics housing.
The threaded interface between the sensor module and the electronics
housing is hermetically sealed before shipment. The integrity of this seal is
necessary for the safe operation of the transmitter during accident conditions.
If the seal is broken, reseal it according to “Connecting the Electrical Housing
to the Sensor Module” on page 5-7.
1.
Mount the bracket to a panel or other flat surface as shown in
Figure 2-4. Use four 3/8-in. diameter bolts (not supplied with unit). SAE
grade 2 bolts were used during qualification testing. Torque each bolt
to 19 ft-lb (26 N-m).
2.
Attach the transmitter to the mounting bracket, as shown in
Figure 2-4. Use four 7/16-20 ⫻ 3/4 bolts with washers (supplied with
unit). Torque each bolt to 21 ft-lb (29 N-m).
Figure 2-4. Typical Transmitter Mounting Bracket Configuration.
2.3
(58)
Center of Gravity
(Includes Bracket)
2.3
(58)
1.2
(30)
Center of Gravity
(Includes Bracket)
1.8
(45.7)
4.93
(125)
2.81 (71.4)
2.81
(71.4)
5
(127)
2.75
(69.9)
3
/8-in.
Bolts (4)
(Customer
Supplied)
PANEL MOUNTING HOLE
PATTERN
(BACK SIDE)
10 (254)
Minimum
Clearance
MOUNTING BRACKET FOR PANEL
MOUNT SHOWN IN TYPICAL
MOUNTING CONFIGURATION
NOTE
Dimensions are nominal in inches (millimeters).
2-6
ACCEPTABLE ALTERNATE
MOUNTING
NOTES
1. Orientation with respect to gravity is not critical.
2. Units can alternately be mounted with process
connection adjacent to bracket.
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 2-5. Transmitter Dimensional Drawings.
ROSEMOUNT 1154DP AND 1154HP
4.7 Max. (119.4)
0.75 (19)
Clearance for
Cover Removal
(typical)
4.72 Max. (119.9)
9 Max.
(228.6)
Nameplate
(remove for zero
and span adjust)
1
/2–14 NPT
Conduit
Transmitter
Connection
Circuitry
(1 Place)
(this side)
7
/16–20
UNF
(typical)
Terminal
Connections
(this side)
3.7
(94)
1.63
(41.3)
Dim.
A
3.4 (86.4)
Welded
Drain/Vent Valve
(2) (optional 1/4–
18 NPT
available)
7
/16–14 UNC
(4 places)
0.8 (20) To End of Mating Tube
3
/8-in. Mating
Tubing
Compression Fittings (2) Swagelok
for 3/8-in. Tubing (optional 1/4–18
NPT available)
0.8
(20)
Pressure
Range Code
Dimension
A
4, 5
6, 7
8
9
0
2.13 (54)
2.19 (55.6)
2.25 (57.2)
2.28 (57.9)
2.33 (59.1)
DETAIL A
ROSEMOUNT 1154GP
4.7 Max. (119.4)
Nameplate
(remove for zero
and span adjust)
9 Max.
(228.6)
1
/2–14 NPT Transmitter
Circuitry
Conduit
(this side)
Connection
(1 Place)
Terminal
Connections
(this side)
7
/16–20
UNF
(typical)
1.63
(41.3)
0.75 (19) Clearance
for Cover Removal
(typical)
4.72 Max. (119.9)
3.7
(94)
Low Side
Vent
Dim.
A
NOTE
Dimensions are nominal in inches
(millimeters).
3.4 (86.4)
Welded
Drain/Vent
Valve (1)
(optional 1/4–18
NPT available)
Low Side
Vent
7
/16–14 UNC
(4 places)
0.8 (20) To End of Mating Tube
Compression Fittings (1) Swagelok for 3/8-in.
Tubing (optional 1/4–18 NPT available)
2-7
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Conduit
1.
Seal the conduit threads with thread sealant. (The transmitter conduit
seal interface was qualified using Grafoil™ tape.) Conduit threads
mate with a standard 1/2–14 NPT male fitting.
2.
Starting at zero thread engagement, install the conduit into the
transmitter between 4 and 7 turns, or a minimum of 12.5 ft-lb (16.9
N-m). Hold the electronics housing securely to avoid damaging the
threaded neck seal between the sensor module and the electronics
housing during conduit installation.
3.
Provide separate support for the conduit if necessary.
Figure 2-6. Transmitter Installation Configuration.
Plugged Tees for
Steam Service or
Sealing Fluid
H
Flow
Plugged Tee for
Steam Service or
Sealing Fluid
Sufficient
Length
for Cooling
3-Valve Manifold
L
3-Valve
Manifold
Blocking
Valve
Sufficient
Length
for Cooling
Flow
H
Drain/Vent
Valve
Drain/Vent
Valves
ROSEMOUNT 1154DP, HP
ROSEMOUNT 1154GP
LIQUID SERVICE
Electrical
Drain/Vent
Valve
L
Blocking Valves
Sufficient
Length
for Cooling
Drain/Vent
Valves
ROSEMOUNT 1154 GP
ROSEMOUNT 1154DP, HP
GAS SERVICE
1.
Remove the cover from the terminal side of the transmitter
(see Figure 2-5 on page 2-7).
2.
Connect the power leads to the “SIGNAL” terminals on the transmitter
terminal block (see Figure 2-7 on page 2-9). Torque the terminal
screws to 5 in-lb (0.6 N-m), or hand-tight.
NOTE
Do not connect signal leads to the “TEST” terminals.
2-8
3.
Recheck connections for proper polarity.
4.
Check the cover O-ring grooves for cleanliness. If chips or dirt are
present, clean the seat and mating portion of the cover with alcohol.
Lubricate replacement O-ring with O-ring grease (RMT P/N
01153-0248-0001 or P/N 01153-0053-0001). The transmitter was
qualified using Dow Corning® 55 Silicone O-ring Grease.
5.
Spray the inside threads of the electronics covers with cover lubricant
(Rosemount P/N 01153-0333-0001 or equivalent) if necessary; if
covers are already sufficiently lubricated, do
not spray.
6.
Carefully replace cover and tighten to 16.5 ft-lb (22.4 N-m).
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 2-7. Transmitter
Terminal Block.
Signal Terminals
Test Terminals
2-9
Reference Manual
Rosemount 1154
2-10
00809-0100-4514, Rev BA
January 2008
Reference Manual
00809-0100-4514, Rev BA
January 2008
Section 3
Rosemount 1154
Calibration
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1
Calibration Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-2
OVERVIEW
Each transmitter is factory calibrated to the range specified by the customer.
This section contains the following transmitter calibration information:
•
Calibration
Span Adjustment
Zero Adjustment
•
Calibration Procedures
Zero and Span Adjustment
Linearity Adjustment
Damping Adjustment
Correction for High Line Pressure
CALIBRATION
The Rosemount 1154DP, HP, and GP transmitters are factory calibrated to the
range shown on the nameplate. This range may be changed within the limits
of the transmitter. Zero may also be adjusted to elevate or to suppress. The
span and zero adjustments are external and located under
the nameplate.
Span Adjustment
The span on any Rosemount 1154 transmitter is continuously adjustable to
allow calibration anywhere between maximum span and 1/6 of maximum span
(1/4 of maximum span for Range Code 0). For example, the span on a Range
Code 4 transmitter can be continuously adjusted between 0–150 and 0–25
inH2O.
Zero Adjustment
The zero can be adjusted for up to 500 percent of span suppression (300
percent for Range Code 0) or 600 percent of span elevation (400 percent for
Range Code 0) (see Figure 3-1 on page 3-2).
The zero may be elevated or suppressed to these extremes with the limitation
that no applied pressure within the calibrated range exceeds the full-range
pressure limit. For example, a Range Code 4 transmitter cannot be calibrated
for 150 to 200 inH2O (only 300 percent zero suppression) because the 200
inH2O exceeds the 150 inH2O upper range pressure limit of a Range Code 4.
The transmitter may be calibrated to cross zero, (e.g., –75 to 75 inH2O) but
this may result in a slight loss of linearity.
www.rosemountnuclear.com
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 3-1. Zero Adjustment
Range.
20
Output
(mA)
600% Zero Elevation
4
–150
–125 –100 –75 –50
–25
0
25
Pressure (inH2O)
600% Zero Elevation➀
20
Output
(mA)
4
0
25
Pressure (inH2O)
No Zero Elevation or Suppression➀
20
Output
(mA)
4
0
25
50
75
100 125 150
Pressure (inH2O)
500% Zero Suppression➀
➀ Graphs based on a Range Code 4 (0–25 to 0–150 inH2O)
Rosemount 1154 with a calibrated span of 25 inH2O.
CALIBRATION
PROCEDURES
Zero and Span
Adjustment
NOTE
The Rosemount 1154 Pressure Transmitter contains electronic circuit boards
which may be static sensitive.
NOTE
Covers need not be removed for zero and span adjustment.
The zero and span adjustment screws are accessible externally. They are
located behind the nameplate on the side of the electronics housing (see
Figure 3-2 on page 3-3). The transmitter output increases with clockwise
rotation of the adjustment screws.
The zero adjustment screw has very little effect on the span. The span
adjustment, however, does affect the zero. The effect of interaction is more
apparent with suppression or elevation. The span adjustment changes the
zero output and the full-scale output by approximately the same percentage.
Therefore, it is best to calibrate the transmitter from zero to the desired span
and finish the calibration by adjusting the zero screw to achieve the desired
elevation or suppression.
3-2
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 3-2. Zero and Span
Adjustment Screws.
Zero
Span
Example (for Range Code 4)
Initial transmitter calibration: 25 to 125 inH2O
(100 inH2O span with zero suppressed 25 inH2O)
Desired transmitter calibration: –75 to –25 inH2O
(50 inH2O span with zero elevated 75 inH2O)
1.
Adjust the zero to eliminate any existing zero elevation or
suppression. With 0 inH2O pressure applied to the transmitter, turn
the zero adjustment until the output reads 4 mA. The unit is now
calibrated for 0 to 100 inH2O.
2.
Adjust the span to the desired new span. To reduce the span, turn the
span screw until the output, with 0 inH2O pressure input, equals:
100 inH 2 O
Span- = 4 mA × ----------------------------- = 8 mA
4 mA × Existing
----------------------------------Desired Span
50 inH 2 O
3.
Adjust the zero screw to bring the output, with 0 inH2O input, back to
4 mA. The transmitter calibration should now be very close to 0 to 50
inH2O.
4.
Check full-scale output and fine tune the span and zero adjustment if
required. Remember zero adjustments do not affect span, but span
adjustments do affect zero predictably. Adjusting the span screw
affects the zero 1/5 as much as it affects the span. To compensate for
this effect, simply overadjust by 25 percent.
For example, if, after completing step 3, the transmitter output reads
19.900 mA at 50 inH2O, turn the span potentiometer until the output
(at 50 inH2O) reads 20.025 mA.
19.900 + (20.000 – 19.900) ⫻ 1.25 =
19.900 + 0.125 = 20.025
Since the span adjustment affects zero 1/5 as much as the span, the
0.125 mA increase in span causes a 0.025 mA increase in zero.
Therefore, turn the zero adjustment (at 50 inH2O) until the output
reads 20.000 mA. The unit should now be calibrated for 0 to 50
inH2O.
5.
Zero Elevation/Suppression. Elevate zero. Turn the screw until the
output reads 4 mA with –75 inH2O applied to the high side of the
transmitter (applying 75 inH2O to the low side of the transmitter will
give the same result). The output may stop changing before the
desired 4 mA reading is obtained. If this occurs, turn off power to the
unit and unplug the amplifier board (refer to “Electrical Housing
Disassembly” on page 5-6 and Table 5-1 on page 5-5). To elevate or
suppress zero a large amount, use the following procedure:
3-3
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Material
•
Wire: 22-gauge tinned solid copper – Fed Spec QQW343, ASTM B33
•
Solder: 60% tin, 40% lead (60/40) – Fed Spec QQ-S-571
•
Flux: MIL F 14256, Type A, Fed Spec QQ-S-571 Type RA
Method
a. Locate the three turret terminals on the component side of the
amplifier board. Remove any jumper wires between them (see
Figure 3-3).
b. To elevate zero, connect a jumper wire between the middle
terminal and the terminal marked “EZ” (see Figure 3-3, Detail B).
c. Wrap the jumper wire once around each terminal and cut off
any excess.
d. Solder the jumper wire to the terminals using proper electronics
soldering techniques. Clean solder joints thoroughly with isopropyl
alcohol.
e. Plug the amplifier board back in and complete the
zero adjustment.
To suppress zero, follow the same procedure, except connect the jumper wire
between the middle terminal and the terminal marked “SZ” (see Figure 3-3,
Detail C).
6.
Recheck full scale and zero and fine tune if necessary.
NOTE
There is some mechanical backlash in the zero and span adjustments, so
there is a dead band when you change the direction of adjustment. Because
of the backlash, the simplest procedure, if the desired setting is overshot, is to
intentionally overshoot a larger amount before reversing the direction of the
adjustment.
Figure 3-3. Jumper Wire
Placement.
Linearity Adjustment
3-4
DETAIL A
Moderate
Elevation/
Suppression
(No Jumper Wire)
DETAIL B
(To Elevate Zero)
Jumper
Wire
DETAIL C
(To Suppress Zero)
Jumper
Wire
In addition to the span and zero adjustments, there is a linearity adjustment
located inside the transmitter on the amplifier board (see Figure 3-4 on
page 3-5). Linearity is factory calibrated for optimum performance over the
calibrated range of the instrument and is not normally adjusted in the field. If
you want to maximize linearity over some particular range, use the following
procedure:
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
1.
Apply mid-range pressure and note the error between theoretical and
actual output signal.
2.
Apply full-scale pressure. Multiply the error noted in step 1 by six and
by the rangedown factor:
Allowable SpanRangedown Factor = Maximum
-------------------------------------------------------------------Calibrated Span
3.
Add the result to the full-scale output for negative errors, or subtract
the result from the full-scale output for positive errors by adjusting the
linearity trimmer (see Figure 3-4). Example: At
4-to-1 rangedown the midscale point is low by 0.05 mA. Therefore,
adjust the “Linearity” trimmer until full-scale output increases by (0.05
mA ⫻ 6 ⫻ 4) = 1.2 mA.
4.
Readjust zero and span.
NOTE
If you remove either cover during the above procedures, replace the O-ring
and torque the cover per the instructions given in Section 5 Maintenance
and Troubleshooting. Spare cover O-rings are supplied with each
transmitter.
Figure 3-4. Linearity and
Damping Adjustment.
Damping
Adjustment
(Optional)
Linearity
Adjustment
Electronics Side of
Transmitter
Housing (Cover
Removed)
Damping Adjustment
Damping electronics are available as an option. Transmitters with standard
electronics can be retrofitted with the adjustable damping feature by changing
out both the amplifier board (RMT P/N 01154-0021-0004) and the calibration
board (RMT P/N 01154-0023-0002).
3-5
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
The damping adjustment permits damping of rapid pressure variations by
adjusting the single-turn trim potentiometer located on the upper right-hand
side of the amplifier board (see Figure 3-4). The available settings, when
adjusted to the maximum position, provide time-constant values of at least 1.2
seconds for Range Code 4 and 0.8 seconds for Range Codes 5–9 and 0.
Transmitters with the electronic damping option are calibrated and shipped
with the adjustment set at the counterclockwise stop, giving the minimum
time-constant.
To adjust the damping, turn the damping adjustment potentiometer until the
desired time-constant is obtained. It is best to set the damping to the shortest
possible time-constant. Since transmitter calibration is not affected by the
damping setting, you may adjust the damping with the transmitter installed on
the process.
The damping adjustment potentiometer has positive stops at both ends. Forcing
the potentiometer beyond the stops may cause permanent damage.
NOTE
If you remove either cover during the above procedures, replace the O-ring
and torque the cover per the instructions given in Section 5 Maintenance
and Troubleshooting of this manual. Spare cover O-rings are supplied with
each transmitter.
Correction For High Line
Pressure (Rosemount
1154DP and 1154HP
Only)
Span
If a differential transmitter is calibrated with the low side at ambient pressure
but will be used at high line pressure, correct the span adjustment to
compensate for the effect of static pressure on the unit. If zero is elevated or
suppressed, also correct the zero adjustment. Correction factors, expressed
in percent of differential pressure input at end points per 1,000 psi static
pressure, are:
Range Codes 4, 5, and 8:
+0.75% of input/1,000 psi
Range Codes 6 and 7:
+1.25% of input/1,000 psi
The correction procedure below uses the following example:
Range Code 5, calibrated at –100 to 300 inH2O, to be operated at 1,200 psi
line pressure. Note that steps 3–6 are omitted for ranges based at zero
differential pressure.
3-6
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
1.
Calibrate the unit per preceding section to output = 4 mA at –100
inH2O and 20 mA at 300 inH2O.
2.
Calculate correction factor:
0.75 %
------------------------ × 1, 200 psi = 0.9% differential input
1,000 psi
3.
Calculate zero adjustment correction in terms of pressure:
0.9 % × – 100 inH 2 O = – 0.9 inH 2 O
4.
Convert pressure correction to percent of input span:
– 0.9 inH 2 O
---------------------------------------------------------------- = – 0.225 % span
400 inH 2 O input span
5.
Calculate correction in terms of output span (mA):
– 0.225 % × 16 mA span = – 0.036 mA
6.
Add the milliamp correction to the ideal zero output (4 mA). This is the
corrected ideal zero output:
4.00 mA – 0.036 = 3.964 mA
7.
Calculate full-scale adjustment correction in terms of pressure:
0.9 % × 300 inH 2 O = 2.7 inH 2 O
8.
Repeat step 4 with the results of step 7:
2.7 inH 2 O
---------------------------------------------------------------- = 0.675 % span
400 inH 2 O input span
9.
Repeat step 5 with the result of step 8:
0.675 % × 16 mA span = 0.108 mA
10. Add the mA correction to the ideal full-scale output (20 mA). This is
the corrected ideal full-scale output:
20.00 mA + 0.108 mA = 20.108 mA
11. Readjust zero and span adjustments for corrected outputs:
3.964 mA at –100 inH2O
20.108 mA at 300 inH2O
There is an uncertainty of ±0.5 percent of input reading per 1,000
psi associated with the span correction.
Zero
Zero shift with static pressure is not systematic. However, if the calibrated
range includes zero differential pressure, the effect can be trimmed out after
installation and with the unit at operating pressure.
3-7
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Equalize pressure to both process connections, and turn the zero adjustment
until the ideal output at zero differential input is observed. Do not readjust the
span potentiometer.
If the transmitter does not include zero differential pressure within its
calibrated span, the zero effect or zero correction can be determined before
the unit is suppressed or elevated to eliminate the zero effect after correcting
for the span effect.
The following procedure illustrates how to eliminate the zero effect for a
non-zero differential pressure calibration. The example uses a Range Code 5,
calibrated from 100 to 500 inH2O, with 1,200 psi static line pressure.
1.
Using standard calibration procedures, calibrate the unit to the
required span, with the 4 mA or zero point corresponding to zero
differential pressure:
4 mA at 0 inH2O and 20 mA at 400 inH2O
2.
Apply static pressure to both high and low process connections with
zero differential pressure across the transmitter, and note the zero
correction (zero shift). For example, if the output reads 4.006 mA, the
zero correction is calculated as:
4.00 mA – 4.006 mA = –0.006 mA
Note the sign associated with this correction, as this result is added
when determining the final, ideal transmitter output.
3.
Remove static pressure and correct for the span effect as outlined in
the span correction procedure. Calibrate the unit to the calculated
output values. If, for example, the span correction procedure yielded
4.029 mA and 20.144 mA, calibrate the unit for:
4.029 mA at 100 inH2O
20.144 mA at 500 inH2O
4.
Add the zero correction (–0.006 mA), found in step 2, to the ideal zero
point value calculated in step 3.
4.029 mA + (–0.006 mA) = 4.023 mA
5.
To eliminate the zero effect, readjust the zero potentiometer so the
output reads the ideal zero point calculated in step 4 (do not readjust
the span potentiometer). Note that all the calibration points will shift
the same amount toward the correct reading. The example output is
now 4.023 mA at 100 inH2O.
The transmitter output is now 4–20 mA over its calibrated span when the unit
is operated at 1,200 psi static line pressure.
3-8
Reference Manual
00809-0100-4514, Rev BA
January 2008
Section 4
Rosemount 1154
Operation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-1
Transmitter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-1
The δ-Cell Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-3
Demodulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-3
Linearity Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-3
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-4
Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-4
Zero and Span Adjustments . . . . . . . . . . . . . . . . . . . . . . . page 4-4
Current Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-4
Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4-4
Reverse Polarity Protection . . . . . . . . . . . . . . . . . . . . . . . . page 4-4
OVERVIEW
TRANSMITTER
OPERATION
This section provides brief descriptions of basic transmitter operations in the
following order:
•
Transmitter Operation
•
The ␦-Cell™ Sensor
•
Demodulator
•
Linearity Adjustment
•
Oscillator
•
Voltage Regulator
•
Zero and Span Adjustments
•
Current Control
•
Current Limit
•
Reverse Polarity Protection
The block diagram in Figure 4-2 on page 4-3 illustrates the operation of the
transmitter.
The Rosemount 1154 Alphaline Pressure Transmitters have a variable
capacitance sensing element, the δ-Cell (Figure 4-1 on page 4-2). Differential
capacitance between the sensing diaphragm and the capacitor plates is
converted electronically to a 2-wire 4–20 mA dc signal.
⎛ C 2 – C 1⎞
P = K 1 ⎜ -------------------⎟
⎝ C 1 + C 2⎠
Where:
P
www.rosemountnuclear.com
is the process pressure.
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
K1
is a constant.
C1 is the capacitance between the high pressure side and the sensing
diaphragm.
C2 is the capacitance between the low pressure side and the sensing
diaphragm.
I ref
fV p – p = -------------------C1 + C2
Where:
Iref is the current source.
Vp-p is the peak-to-peak oscillation voltage.
f
is the oscillation frequency.
I diff = fV p – p ( C 2 – C 1 )
Where:
Idiff
is the difference in current between C1 and C2.
Therefore:
⎛ C 2 – C 1⎞
P = Constant × I diff = I ref ⎜ -------------------⎟
⎝ C 2 + C 1⎠
Figure 4-1. The δ-Cell.
Leadwires
Capacitor
Plates
Sensing
Diaphragm
Rigid
Insulation
Silicone Oil
Isolating
Diaphragm
4-2
Welded Seals
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 4-2. Electrical Block
Diagram.
SENSOR
DEMODULATOR
CURRENT
DETECTOR
TEST
CURRENT
LIMITER
+
OSCILLATOR
OSC.
CONTROL
AMP.
+
SIGNAL
VOLTAGE
REGULATOR
CURR.
CONTROL
AMP.
REVERSE
POLARITY
PROTECTION
CURRENT
CONTROL
THE δ-CELL™ SENSOR
Process pressure is transmitted through an isolating diaphragm and silicone
oil fill fluid to a sensing diaphragm in the center of the δ-Cell. The reference
pressure is transmitted in like manner to the other side of the sensing
diaphragm.
The position of the sensing diaphragm is detected by the capacitance plates
on both sides of the sensing diaphragm. The capacitance between the
sensing diaphragm and either capacitor plate is approximately 150 pf. The
sensor is driven through transformer windings by an oscillator at roughly 32
kHz and 30 Vp-p.
DEMODULATOR
The demodulator consists of a diode bridge that rectifies the ac signal from
the sensor cell to a dc signal.
The oscillator driving current, Iref (the sum of the dc currents through two
transformer windings) is controlled to be a constant by an integrated circuit
amplifier.
The dc current through a third transformer winding is a current directly
proportional to pressure, i.e.,
I diff = fV p – p ( C 2 – C 1 )
The diode bridge and span temperature compensating thermistor are located
inside the sensor module. The effect of the thermistor is controlled by
resistors located in the electronics housing.
LINEARITY
ADJUSTMENT
Linearity is adjusted by a variable-resistance network, capacitor, and diodes.
The currents generated through this part of the circuit are summed into the
inputs of the oscillator control circuit. This provides a programmed correction
that raises the oscillator peak-to-peak voltage to compensate for first-order
nonlinearity of capacitance as a function of pressure.
4-3
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
OSCILLATOR
The oscillator has a frequency determined by the capacitance of the sensing
element and the inductance of the transformer windings.
The sensing element capacitance is variable. Therefore, the frequency is
variable about a nominal value of 32 kHz.
An integrated circuit amplifier is used as a feedback control circuit and
controls the oscillator drive voltage such that:
I ref
fV p – p = -------------------C1 + C2
VOLTAGE REGULATOR
The transmitter uses a zener diode, transistor, and resistors to provide a
constant voltage of 6.4 V dc for the reference and 7 V dc for the oscillator.
ZERO AND SPAN
ADJUSTMENTS
Zero adjustment components consist of a potentiometer and resistor that
develop a separate adjustable current that sums with the sensor current. The
coarse zero switch switches resistors into the circuit as needed.
Span adjustment is performed with a potentiometer which determines the
amount of loop current which is sensed and fed back to the current control
amplifier.
CURRENT CONTROL
The current control amplifier consists of an integrated circuit, two transistors,
and associated components. The IC reference voltage is established at the
junction of a resistor network. The current control amplifier drives the current
control to a level such that the current detector feeds back a signal equal to
the sum of the zero current and the variable sensor current.
CURRENT LIMIT
A current limiter prevents the output current from exceeding 30 mA in an
overpressure condition.
REVERSE POLARITY
PROTECTION
A zener diode provides reverse polarity protection.
4-4
Reference Manual
00809-0100-4514, Rev BA
January 2008
Section 5
Rosemount 1154
Maintenance and
Troubleshooting
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-1
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-2
Test Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-2
Board Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-2
Sensing Module Checkout . . . . . . . . . . . . . . . . . . . . . . . . . page 5-3
Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-4
Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-6
Post Assembly Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-9
Use only the procedures and new parts specifically referenced in this manual to
ensure specification performance and certification compliance. Unauthorized
procedures or parts can render the instrument dangerous to life, limb, or property.
OVERVIEW
This section outlines a technique for checking out the components, a method
for disassembly and reassembly, and a troubleshooting guide.
NOTE
Maintenance of traceability of any replacement parts is the responsibility of
the user (see “Important Notice” on page 6-11 and Important Notice at the
beginning of this manual preceding the Table of Contents).
The Rosemount 1154 has no moving parts and requires a minimum of
scheduled maintenance. Calibration procedures for range adjustment are
outlined in Section 3: Calibration. A calibration check should be conducted
after inadvertent exposure to overpressure, unless your plant considers this
factor separately in the plant error analysis.
Test terminals are available for in-process checks. For further checks, the
transmitter can be divided into three active physical components: the sensing
module, the amplifier board, and the calibration board.
An exploded view of the transmitter is provided in Figure 5-2 on page 5-5. In
the following procedures, numbers in parentheses refer to item numbers in the
exploded view.
www.rosemountnuclear.com
Reference Manual
Rosemount 1154
SAFETY MESSAGES
00809-0100-4514, Rev BA
January 2008
Instructions and procedures in this section may require special precautions to
ensure the safety of the people performing the operations. Information that
raises potential safety issues is indicated by a warning message. The following
warning messages appear in this section.
Use only the procedures and new parts specifically referenced in this manual to
ensure specification performance and certification compliance. Unauthorized
procedures or parts can render the instrument dangerous to life, limb, or property.
Process O-rings may retain some process fluid after disassembly of process
flanges. If this fluid is determined to be contaminated, take appropriate safety
measures.
TEST TERMINALS
The test terminals are connected across a diode through which the loop signal
current passes. The indicating meter or test equipment shunts the diode when
connected to the test terminals. As long as the voltage across the terminals is
kept below the diode threshold voltage, no current passes through the diode.
To ensure that there is no current leaking through the diode while making a test
reading or when connecting an indicating meter, the resistance of the test connection or meter should not exceed 10 Ω .
BOARD CHECKOUT
NOTE
Numbers in parentheses refer to item numbers in Figure 5-2 on page 5-5.
NOTE
The Rosemount 1154 Pressure Transmitter contains electronic circuit boards
which may be static sensitive.
You can easily check the printed circuit boards (5 and 6) for a malfunction by
substituting spare boards into the circuit. If this procedure turns up a malfunctioning board, return the defective board to Rosemount Nuclear Instruments,
Inc. for replacement. Because of parts traceability, qualification becomes the
responsibility of the customer in the event of unauthorized board repairs.
Figure 5-1. Header Board
Connections.
COMPONENT SIDE UP
5-2
Reference Manual
00809-0100-4514, Rev BA
January 2008
SENSING MODULE
CHECKOUT
Rosemount 1154
NOTE
Numbers in parentheses refer to item numbers in Figure 5-2 on page 5-5.
The sensing module (12) is not field-repairable and must be replaced if
defective. If no defect such as a punctured isolating diaphragm or loss of fill
fluid is observed, check the sensing module in the following manner:
1.
Disengage the header assembly board (4) as described in step four
of the electrical housing disassembly procedure on page 5-6. You
need not remove the sensing module from the electrical housing for
checkout.
2.
Jump connections 1 and 2 on the header assembly board (see Figure
5-1 on page 5-2).
3.
Using a low-voltage ohmmeter, check the resistance between the
jumper wire and the sensing module housing. This resistance should
be greater than 10 MΩ. Remove the jumper wire.
4.
Jump connections 3 and 4 on the header assembly board and repeat
step 3 (see Figure 5-1 on page 5-2).
NOTE
The above procedure does not completely test the sensing module. If circuit
board replacement does not correct the abnormal condition and no other
problems are obvious, replace the sensing module.
5-3
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
DISASSEMBLY
PROCEDURE
Process Flange Removal
NOTE
Numbers in parentheses refer to item numbers in Figure 5-2 on page 5-5.
NOTE
The Rosemount 1154 Pressure Transmitter contains electronic circuit boards
which may be static sensitive.
Process O-rings may retain some process fluid after disassembly of process
flanges. If this fluid is determined to be contaminated, take appropriate safety
measures.
NOTE
Read the Process Flange Reassembly Procedure on page 5-8 before
attempting disassembly. Special testing and traceability are required.
1.
Remove the transmitter from service before disassembling flanges.
2.
Detach process flanges (13, 15) by removing the four large bolts (14).
Take care not to scratch or puncture the isolating diaphragms.
Identify high and low (“H” and “L”) flanges for reassembly.
NOTE
Carefully remove the O-rings (11) from the cell if they do not come off when
the flange is removed. Do not pry the O-ring from its seat, as you may
damage the isolating diaphragm.
3.
5-4
Clean isolating diaphragms with a soft rag and a mild cleaning
solution. Do not use any chlorine or acid solutions to clean the
diaphragms. Rinse diaphragms with distilled water.
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Figure 5-2. Rosemount 1154, Exploded View.
17
1
2
20
16
3
18
5
4
19
6
7
2
C
A
1
10
B
D
9
10
8
13
15 Flange
Module
C
11
A
12
B
11
12
D
15
11 O-ring
14
Detail A
Table 5-1. Rosemount 1154 Parts List.
Part
Description
Part
Description
1
Electronics Cover
11
Metal O-Ring for Process Flange
2
O-Ring for Electronics Cover
12
Sensor Module
3
Electronics Housing
13
Process Flange
4
Header Assembly Board
14
Process Flange Bolts
5
Calibration Board
15
Process Flange
6
Amplifier Board
16
Zero and Span Adjustment Screws
7
Holding Screws
17
Nameplate
8
Process Flange Nuts
18
Snap Rings
9
Sensor Module Lock Nut
19
O-Ring for Adjustment Screw
10
Valve Stem
20
Nameplate Screws
5-5
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Electrical Housing
Disassembly
Removing Sensor
Module from Electrical
Housing
REASSEMBLY
PROCEDURE
1.
The signal terminals and test terminals are accessible by unscrewing
the cover (1) on the terminal side. This compartment is identified as
“terminal side” on the nameplate. The terminals are permanently
attached to the housing and must not be removed.
2.
Circuit boards are located in a separate compartment identified as
“Circuit Side” on the nameplate. Remove power from the transmitter
before removing the circuit side cover. Unscrew the cover (1) on the
circuit side to access the circuit boards. A special cover wrench (RMT
P/N 01153-0382-0001) is available from Rosemount to remove and
replace the housing covers.
3.
Unplug the amplifier board (6) after removing 3 holding screws (7).
4.
The header assembly board (4) is permanently attached to the sensor
module (12) and contains the temperature-compensating resistors.
Carefully pull this board off the bayonet pins and rotate the board 180
degrees about the axis formed by the connecting leads. This allows
access to the calibration board (5).
5.
Disconnect the calibration board (5) by aligning the zero and span
adjust screws so that their slots are perpendicular to the board.
Remove the board by inserting a 6–32 screw in the rivnut on the
board and carefully pulling the board off the bayonet pins.
6.
If replacement of the zero and span adjustment screws (16) is
necessary, remove the nameplate (17) and detach the snap rings (18)
inside the housing.
1.
Remove flanges per Process Flange Removal Section on page 5-4.
2.
Remove amplifier board and calibration board as described in the
Electrical Housing Disassembly Section above.
3.
Loosen the lock nut (9).
4.
Unscrew the sensor module (12) from the electronics housing,
simultaneously turning the header board and leads to prevent them
from being twisted or damaged. The threaded connection has a
sealing compound on it and must be broken loose. Be careful not to
damage the isolating diaphragms when unscrewing the sensor
module. Then carefully pull the header assembly board (4) through
the hole.
5.
The sensor module (12) is a welded assembly and cannot be further
disassembled.
NOTE
Numbers in parentheses refer to item numbers in Figure 5-2 on page 5-5.
NOTE
The Rosemount 1154 Pressure Transmitter contains electronic circuit boards
which may be static sensitive.
5-6
Reference Manual
00809-0100-4514, Rev BA
January 2008
Preliminary
Connecting the Electrical
Housing to the Sensor
Module
Electrical Housing
Reassembly
Rosemount 1154
1.
Replace the cover O-rings (2) whenever you remove a cover. Clean
the sealing areas with alcohol, if necessary, and lightly grease the
O-ring with Dow Corning 55 Silicone O-ring Grease (Rosemount P/N
01153-0248-0001 or P/N 01153-0053-0001). Spray the inside threads
of the electronics covers with cover lubricant (Rosemount P/N
01153-0333-0001 or equivalent) if necessary; if covers are already
sufficiently lubricated, do not spray.
2.
Verify that the circuit boards are clean.
3.
Verify that the bayonet pins on the connection board are clean.
4.
If you remove the sensor module, clean the thread sealant from the
sensor module threads, lock nut, and electronics housing threads
with a wire brush.
1.
Run the lock nut down to the base of the sensor module threads.
2.
Apply a heavy, continuous bead (about 3/8-in. wide) of Loctite®
580-PST sealant (RMT P/N 01153-0329-0001) around the top sensor
module threads.
3.
Insert the header assembly board (4) through the hole in the bottom
of the electronics housing.
4.
Screw the sensor module (12) into the electrical housing (3) making
sure that five full threads are engaged. Be careful not to damage or
twist the sensor leads. Turn the header board to avoid
twisting wires.
5.
Align the sensor module with the high and low pressure sides
oriented per Figure 2-5 on page 2-7. Alternately, tighten the module
one-half turn further to reverse the orientation of the module about the
electronics housing.
6.
Tighten the lock nut (9) to 35 ft-lb (48 N-m) torque.
7.
Wipe off excess sealant.
8.
Place the assembled unit in an oven at 200 ±5 °F (93 ± 3 °C) for 12
hours to cure the sealant.
1.
Replace the zero and span adjustment screw O-rings (19) whenever
you remove the zero and span adjustment screws (16). Lightly grease
the O-rings with Dow Corning 55 Silicone O-ring Grease (Rosemount
P/N 01153-0248-0001 or P/N 01153-0053-0001). Reinstall the
adjustment screws and secure with snap rings (18).
2.
Align the zero and span adjustment screws with the potentiometer
stems on the calibration board (5) and push the calibration board onto
the bayonet pins.
3.
Slide the header assembly board (4) onto the bayonet pins with the
component side toward the pins. Slide any excess wire behind the
calibration board, taking care to avoid kinks.
4.
Push the amplifier board (6) onto the bayonet pins and secure with
holding screws (7). Use nominal torque of 10 in-lb (1.1 N-m).
5.
Carefully replace the cover and tighten to 16.5 ft-lb (22.4 N-m)
(“Preliminary” on page 5-7).
6.
Replace the nameplate (17), and secure with two nameplate
screws (20).
5-7
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Process Flange
Reassembly
1.
Replace the metal O-rings (11) with new O-rings if the flanges
were removed.
2.
Carefully place an O-ring (11) in the isolator well of the high side (“H”)
of the sensing module. Place the O-ring so the edge of the rolled ring
faces the module (see Detail A of Figure 5-2 on page 5-5).
3.
Carefully place the flange (13 or 15) as shown in Figure 5-2 on
page 5-5. Take care not to disturb the O-rings or damage the
diaphragms.
4.
On differential units, repeat steps 2 and 3 for the low side (“L”) of the
module. If a gage unit has two O-rings (one on each side), repeat
steps 2 and 3 for the low side. If the gage unit has only one O-ring,
reassemble with one O-ring on the high side.
5.
Keeping the flanges parallel to each other and to the module faces,
insert the four bolts (14) (and four washers on Range Code 9) and
finger-tighten the nuts (8).
Each spare parts kit contains the correct number of nuts, bolts, and
washers for the specific transmitter range code it is designated for.
Due to consolidation of parts kits, the bolt length and quantity of
washers required may differ from existing transmitter assemblies
and/or parts kits. Verify by part number that the appropriate spare
parts kit is used for the transmitter range code being re-assembled.
Contact Rosemount Nuclear Instruments, Inc. if there are questions.
6.
Evenly seat the flanges on the sensor module housing, using a hand
torque wrench as specified in steps 7 through 11. See Figure 5-2 on
page 5-5 to identify the bolts.
7.
Alternately tighten bolts A and B to 10 ft-lb (13.6 N-m) torque.
8.
Alternately tighten bolts C and D to 10 ft-lb (13.6 N-m) torque.
9.
Check the torque on bolts A and B.
10. Check the torque on bolts C and D.
11. Repeat steps (7)-(10) at 15 ft-lb (20 N-m) torque, at 20 ft-lb
(27 N-m) torque, at 25 ft-lb (34 N-m) torque, at
30 ft-lb (41 N-m) torque, and at 35 ft-lb (48 N-m) torque until all bolts
are torqued to 35 ±1 ft-lb (48 ±1 N-m).
12. Expose all ranges of gage transmitters to two temperature cycles
over the expected temperature operating range before calibrating.
Expose differential and high-line differential Range Code 4’s to two
temperature cycles over the expected temperature operating range
before calibrating.
5-8
Reference Manual
00809-0100-4514, Rev BA
January 2008
POST ASSEMBLY TESTS
Rosemount 1154
1.
Conduct hydrostatic testing to 150% of maximum working pressure or
2,000 psi, whichever is greater.
2.
Calibrate the transmitter per the calibration section of this manual.
3.
Conduct nuclear cleaning to 1 ppm chloride content of transmitter
“wetted parts.”
Table 5-2. Torque References.
ITEM(S) TO BE TORQUED
TORQUE VALUE
TOLERANCE
Bracket to Mounting Panel Bolts
19 ft-lb (26 N-m)
±1 ft-lb (1 N-m)
Transmitter to Bracket Bolts
21 ft-lb (29 N-m)
±1 ft-lb (1 N-m)
Swagelok Process Fittings
See Installation Instructions
Drain/Vent Valves
7.5 ft-lb (10 N-m)
±0.5 ft-lb (0.7 N-m)
Covers
16.5 ft-lb (22.4 N-m)
±1 ft-lb (1 N-m)
Module Neck Lock Nut
35 ft-lb (48 N-m)
±1 ft-lb (1 N-m)
Conduit Fitting
4 to 7 turns or a minimum of 12.5 ft-lb (16.9
N-m)
±1 ft-lb (1 N-m)
Flange Bolts
See Process Flange Reassembly
Terminal Block Screws
5 in-lb (0.6 N-m) or hand tight
±1 in-lb (0.1 N-m)
Amplifier Board Screws
Nominal 10 in-lb (1.1 N-m)
—
—
—
Table 5-3. Troubleshooting.
Symptom
High Output
Potential Source
Corrective Action
Primary Element
Check for restrictions at primary element, improper installation or poor condition. Note any
changes in process fluid properties that may affect output.
Impulse Piping
Check for leaks or blockage.
Ensure blocking locking valves are fully open.
Check for entrapped gas in liquid lines, or liquid in dry lines.
Ensure that density of fluid in impulse line is unchanged.
Check for sediment in transmitter process flanges.
Transmitter
Electronics
Make sure that post connectors and the sensor connections are clean. If the electronics are
still suspect, substitute new electronics.
Transmitter
Electronics Failure
Determine faulty circuit board by trying spare boards. Replace faulty circuit board.
Sensing Module
See Sensing Module Checkout section. The sensing element is not field repairable and must
be replaced if found to be defective. See “Disassembly Procedure” for instructions on
disassembly. Check for obvious defects, such as a punctured isolating diaphragm or fill fluid
loss, and contact Rosemount Nuclear Instruments, Inc. at (952) 949-5210.
Power Supply
Check the power supply output voltage at the transmitter.
Continued on Next Page
5-9
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Symptom
Low Output or
No Output
Potential Source
Primary Element
Corrective Action
Check for restrictions at primary element, improper installation or poor condition.
Note any changes in process fluid properties that may affect output.
Loop Wiring
Do not use over 100 volts to check the loop, or damage to the transmitter
electronics may result.
Check for adequate voltage to the transmitter.
Check the milliamp rating of the power supply against the total current being drawn for all
transmitters being powered.
Check for shorts and multiple grounds.
Check for proper polarity at the signal terminal.
Check loop impedance.
Check wire insulation to detect possible shorts to ground.
Erratic Output
Impulse Piping
Ensure that the pressure connection is correct.
Check for leaks or blockage.
Check for entrapped gas in liquid lines.
Check for sediment in the transmitter process flange.
Ensure that blocking valves are fully open and that bypass valves are tightly closed.
Ensure that density of the fluid in the impulse piping is unchanged.
Transmitter
Electronics
Connections
Ensure that calibration adjustments are in allowable range.
Check for shorts in sensor leads.
Make sure post connectors are clean, and check the sensor connections.
If the electronics are still suspect, substitute new electronics.
Test Diode Failure
Replace electronics housing.
Transmitter
Electronics Failure
Determine faulty circuit board by trying spare boards. Replace faulty circuit board.
Sensing Module
NOTE: See Sensing Module Checkout section. The sensing element is not field repairable
and must be replaced if found to be defective. See “Disassembly Procedure” for instructions
on disassembly. Check for obvious defects, such as a punctured isolating diaphragm or fill
fluid loss, and contact Rosemount Nuclear Instruments, Inc. at (952) 949-5210.
Power Supply
Check the power supply output voltage at the transmitter.
Loop Wiring
Do not use over 100 volts to check the loop, or damage to the transmitter
electronics may result.
Check for inadequate voltage to the transmitter.
Check for intermittent shorts, open circuits, or multiple grounds.
5-10
Impulse Piping and
Process
Connections
Check for entrapped gas in liquid lines, or liquid in dry lines.
Transmitter
Electronics
Check for intermittent shorts or open circuits.
Make sure that bayonet and sensor connectors are clean and properly connected.
Transmitter
Electronics Failure
Determine faulty circuit boards by trying spare boards. Replace faulty circuit board.
Power Supply
Check power supply output voltage.
Reference Manual
00809-0100-4514, Rev BA
January 2008
Section 6
Rosemount 1154
Specifications and Reference
Data
Nuclear Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-1
Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . page 6-2
Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . page 6-4
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-6
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-8
Spare Parts Shelf Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-11
Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-11
NUCLEAR
SPECIFICATIONS
Qualified per IEEE Std 323-1974 and IEEE Std 344-1975, as stated in
Rosemount Report D8400102.
Radiation
Accuracy within ±(1.5% of upper range limit + 1.0% of span) during and after
exposure to 55 megarads TID gamma radiation at the centerline at the
following dose rate: 2 megarads/hr for 2 hr,
1.5 megarad/hr for 4 hr, 1 megarad/hr up to
55 megarads TID and an additional 55 megarads TID at a rate of
1 megarad/hr during post-accident operation
Range Code 0: ±(2.25% of upper range limit + 1.0% of span)
Seismic
Accuracy within ±0.5% of upper range limit after a seismic disturbance
defined by a required response spectrum with a ZPA of 7 g
Range Code 0: ±0.75% of upper range limit
Steam Pressure/Temperature
Accuracy within ±(2.5% upper range limit + 0.5% of span) during and after
sequential exposure to steam at the following temperatures and pressures,
concurrent with chemical spray for the first 24 hr:
420 °F (215.6 °C), 50 psig for 3 minutes
350 °F (176.6 °C), 110 psig for 7 minutes
320 °F (160.0 °C), 75 psig for 8 hours
265 °F (129.4 °C), 24 psig for 56 hours
Range Code 0: ±(3.75% of upper range limit + 0.5% of span)
Chemical Spray
Composition is 0.28 molar boric acid, 0.064 molar sodium thiosulfate, and
sodium hydroxide to make an initial pH of 11.0 and a subsequent pH ranging
from 8.5 to 11.0. Chemical spray is sprayed at a rate of
0.25 gal/min/ft2.
www.rosemountnuclear.com
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Post DBE Operation
Accuracy at reference conditions shall be within ±2.5% of upper range limit
(±3.75% for Range Code 0) for one year following DBE.
Quality Assurance Program
In accordance with NQA-1, 10CFR50 Appendix B, and ISO 9001:2000
Nuclear Cleaning
To 1 ppm maximum chloride content
Hydrostatic Testing
To 150% of maximum working pressure or 2,000 psi (13.8 MPA), whichever is
greater
Traceability
In accordance with NQA-1, 10CFR50 Appendix B; chemical and physical
material certification of pressure-retaining parts
Qualified Life
The transmitter qualified life is dependent on continuous ambient temperature
at the installation site (see Figure 6-1). Replacement of amplifier and
calibration circuit boards at the end of their qualified life permits extension of
the transmitter qualified life to the module qualified life. See Rosemount
Report D8400102 for details.
Figure 6-1. Qualified Life vs.
Ambient Temperature.
Module
Qualified Life
Time (Years)
Electronics
Qualified Life
Temperature (°F)
PERFORMANCE
SPECIFICATIONS
Based on zero-based ranges under reference conditions.
Accuracy
±0.25% of calibrated span; includes combined effects of linearity, hysteresis,
and repeatability
Dead Band
None
6-2
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Drift
±0.2% of upper range limit for 30 months
Range Code 0: ±(0.3% of upper range limit)
Temperature Effect
Range Codes 4–9:
±(0.75% upper range limit +0.5% span) per 100 °F (55.6 °C) ambient
temperature change
Range Code 0:
±(1.13% upper range limit +0.5% span) per 100 °F (55.6 °C) ambient
temperature change
Overpressure Effect
Rosemount 1154DP:
Maximum zero shift after 2,000 psi (13.8 MPa) overpressure:
Range Code
Overpressure Effect
4
±0.25% of upper range limit
5
±1.0% of upper range limit
6, 7
±3.0% of upper range limit
8
±6.0% of upper range limit
Rosemount 1154HP:
Maximum zero shift after 3,000 psi (20.68 MPa) overpressure:
Range Code
Overpressure Effect
4
±1.0% of upper range limit
5
±2.0% of upper range limit
6, 7
±5.0% of upper range limit
Rosemount 1154GP:
Maximum zero shift after 2,000 psi (13.8 MPa) overpressure:
Range Code
Overpressure Effect
4
±0.25% of upper range limit
5–8
±1.0% of upper range limit
After 4,500 psi (31.0 MPa) overpressure:
Range Code
Overpressure Effect
9
±0.5% of upper range limit
After 6,000 psi (41.37 MPa) overpressure:
Range Code
Overpressure Effect
0
±0.25% of upper range limit
6-3
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Static Pressure Zero Effect
Rosemount 1154DP:
Per 1,000 psi (6.89 MPa):
Range Code
Static Pressure Zero Effect
4, 5
±0.2% of upper range limit
6–8
±0.5% of upper range limit
Rosemount 1154HP:
Per 1,000 psi (6.89 MPa):
Range Code
Static Pressure Zero Effect
All Ranges
±0.66% of upper range limit
Static Pressure Span Effect
Effect is systematic and can be calibrated out for a particular pressure before
installation. Correction uncertainty is ±0.5% of input
reading/1,000 psi (6.89 MPa).
Power Supply Effect
Less than 0.005% of output span/volt
Load Effect
No load effect other than the change in voltage supplied to
the transmitter
Mounting Position Effect
No span effect; zero shift of up to 1.5 inH2O (372 Pa) which can be calibrated
out
Response Time
Fixed time constant (63%) at 100 °F (37.8 °C) as follows:
Range Code
Response Time
4
0.5 seconds or less
all others
0.2 seconds or less
Adjustable damping is available through a special
N option.
FUNCTIONAL
SPECIFICATIONS
Service
Liquid, gas, or vapor
Output
4–20 mA dc
Power Supply
Design limits are as shown in Figure 2-3 on page 2-5. See qualification report
D8400102 for additional detail.
6-4
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Span and Zero
Continuously adjustable externally
Zero Elevation and Suppression
Maximum zero elevation: 600% of calibrated span
(400% of calibrated span for Range Code 0)
Maximum zero suppression: 500% of calibrated span (300% of calibrated
span for Range Code 0)
Zero elevation and suppression must be such that neither the calibrated span
nor the upper or lower range value exceeds 100% of the upper range limit.
Temperature Limits
Normal operating limits: 40 to 200 °F (4.4 to 93.3 °C)
Qualified storage limits: –40 to 120 °F (–40.0 to 48.9 °C)
Humidity Limits
0–100% relative humidity (NEMA 4X)
Volumetric Displacement
Less than 0.01 in3 (0.16 cm3 )
Turn-on Time
2 seconds maximum. No warm-up required
Pressure Ranges
Rosemount 1154DP and 1154HP:
Range Code
Pressure Ranges
4
0–25 to 0–150 inH2O (0–6.22 to 0–37.3 kPa)
5
0–125 to 0–750 inH2O (0–31.08 to 0–186.4 kPa)
6
0–17 to 0–100 psi (0–0.12 to 0–0.69 MPa)
7
0–50 to 0–300 psi (0–0.34 to 0–2.07 MPa)
8
0–170 to 0–1,000 psi (0–1.17 to 0–6.89 MPa)
(DP units only)
Rosemount 1154GP:
Range Code
Pressure Ranges
4–8
as listed for Rosemount 1154DP
9
0–500 to 0–3,000 psi (0–3.45 to 0–20.68 MPa)
0
0–1,000 to 0–4,000 psi (0–6.89 to 0–27.56 MPa)
Maximum Working Pressure
Rosemount 1154DP and 1154HP:
Static pressure limit
Rosemount 1154GP:
Upper range limit
6-5
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Static Pressure and Overpressure Limits
Rosemount 1154DP:
0.5 psia to 2,000 psig (3.4 kPa abs to 13.8 MPa) maximum rated static
pressure for operation within specifications; overpressure limit is 2,000
psig (13.8 MPa) on either side without damage to
the transmitter.
Rosemount 1154HP:
0.5 psia to 3,000 psig (3.4 kPa abs to 20.7 MPa) maximum rated static
pressure for operation within specifications; overpressure limit is 3,000
psig (20.7 MPa) on either side without damage to
the transmitter.
Overpressure Limits
Rosemount 1154GP:
Operates within specifications from 0.5 psia
(3.4 kPa abs) to upper range limit. Overpressure limits without damage to
the transmitter:
PHYSICAL
SPECIFICATIONS
Range Code
Overpressure Limit
4–8
2,000 psig (13.8 MPa)
9
4,500 psig (31.0 MPa)
0
6,000 psig (41.34 MPa)
Materials of Construction
Isolating Diaphragms:
316L SST
Drain/Vent Valves:
316 SST
Process Flanges:
CF-8M (cast version of 316 SST)
Process O-rings:
316L SST
Electronics Housing O-rings:
Ethylene propylene
Fill Fluid:
Silicone oil
Flange Bolts and Nuts:
Plated alloy steel, as specified in ASTM A540
Electronics Housing:
316 SST
Mounting Bracket:
316L SST
Mounting Bolts (Bracket to transmitter):
SAE J429 carbon steel, Grade 2 or Grade 5
6-6
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Electrical Connections
1
/2–14 NPT conduit with screw terminals
Process Connections
3
/8 in. Swagelok compression fitting, 316 SST
(1/4–18 NPT optional)
Weight
24 lb (10.9 kg) including mounting bracket
6-7
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
ORDERING INFORMATION
Table 6-1. Transmitter Design Specifications.
Model
Description
1154
Alphaline Pressure Transmitters for Nuclear Applications, IEEE Std 323-1974 and IEEE Std 344-1975
Code
Pressure Measurement
DP
HP
GP
Differential Pressure, 2,000 psig (13.8 MPa) Static Pressure Rating
Differential Pressure, 3,000 psig (20.68 MPa) Static Pressure Rating
Gage Pressure
PRESSURE RANGES at 68 °F
Rosemount 1154DP
(Differential)
Rosemount 1154HP
(Differential)
Rosemount 1154GP
(Gage)
4
0–25 to 0–150 inH2O
(0–6.22 to 0–37.3 kPa)
0–25 to 0–150 inH2O
(0–6.22 to 0–37.3 kPa)
0–25 to 0–150 inH2O
(0–6.22 to 0–37.3 kPa)
5
0–125 to 0–750 inH2O
(0–31.08 to 0–186.4 kPa)
0–125 to 0–750 inH2O
(0–31.08 to 0–186.4 kPa)
0–125 to 0–750 inH2O
(0–31.08 to 0–186.4 kPa)
6
0–17 to 0–100 psi
(0–0.12 to 0–0.69 MPa)
0–17 to 0–100 psi
(0–0.12 to 0–0.69 MPa)
0–17 to 0–100 psi
(0–0.12 to 0–0.69 MPa)
7
0–50 to 0–300 psi
(0–0.34 to 0–2.07 MPa)
0–50 to 0–300 psi
(0–0.34 to 0–2.07 MPa)
0–50 to 0–300 psi
(0–0.34 to 0–2.07 MPa)
8
0–170 to 0–1,000 psi
(0–1.17 to 0–6.89 MPa)
—
0–170 to 0–1,000 psi
(0–1.17 to 0–6.89 MPa)
9
—
—
0–500 to 0–3,000 psi
(0–3.45 to 0–20.68 MPa)
0
—
—
0–1,000 to 0–4,000 psi
(0–6.89 to 0–27.56 MPa)
Code
Code
R(1)
Code
A
B(2)
C(2)
D
E(2)
F(2)
G
H
J(2)
L
M(2)
Output
Standard 4–20 mA
Flange Option
Welded 3/8 in. Swagelok Compression Fitting Process Connection and Welded Drain/Vent Valve
¼–18 NPT Process Connection and Welded Drain/Vent Valve
¼–18 NPT Process Connection and Drain Hole (Drain/Vent Valve not supplied)
One Flange Code Option A and One Remote Seal
One Flange Code Option B and One Remote Seal
One Flange Code Option C and One Remote Seal
Two Remote Seals
Welded 3/8 in. Swagelok Compression Fittings on Both Process Connection and Drain/Vent Connection
Welded 3/8 in. Swagelok Compression Fitting Process Connection and ¼–18 NPT Drain Hole
One Flange Code Option H and One Remote Seal
One Flange Code Option J and One Remote Seal
Typical Model Number:1154
DP
4
R
A
(1) The Rosemount 1154 with Output Code R Electronics is also available with adjustable damping. This option is specified
by appending “N0037” to the end of the complete model number, for example, 1154DP4RAN0037.
(2) Note: Customer assumes responsibility for qualifying connection interfaces on these options. Contact Rosemount
Nuclear Instruments, Inc. for details.
6-8
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Table 6-2. Rosemount 1154DP, 1154HP, and 1154GP Spare Parts.
Spare Parts Category(1)
Traceable Part
Quantity Required
Item Number (see Figure 5-2 on page 5-5)
Part Description
Rosemount
1154DP
Rosemount
1154HP
Rosemount
1154GP
Order No.
Order No.
Order No.
Amplifier Cir. Board, Output Code R
Calib. Cir. Board, Output Code R
Amplifier Cir. Board with Damping,
Output Code R
Calib. Cir. Board with Damping,
Output Code R
6
5
1
1
A
A
01154-0001-0005
01154-0002-0001
01154-0001-0005
01154-0002-0001
01154-0001-0005
01154-0002-0001
6
1
A
01154-0021-0004
01154-0021-0004
01154-0021-0004
5
1
A
01154-0023-0002
01154-0023-0002
01154-0023-0002
Sensor Module, 316 SST
0–25/150 inH2O
0–125/750 inH2O
0–17/100 psi
0–50/300 psi
0–170/1,000 psi
0–500/3,000 psi
0–1,000/4,000 psi
12
1
B
B
B
B
B
B
B
01154-0300-0242
01154-0300-0252
01154-0300-0262
01154-0300-0272
01154-0300-0282
—
—
01154-0300-0342
01154-0300-0352
01154-0300-0362
01154-0300-0372
—
—
—
01154-0300-0142
01154-0300-0152
01154-0300-0162
01154-0300-0172
01154-0300-0182
01154-0300-0192
01154-0300-0102
01153-0211-0001
01153-0204-0001
01153-0382-0001
01153-0211-0001
01153-0204-0001
01153-0382-0001
01153-0211-0001
01153-0204-0001
01153-0382-0001
01153-0041-0001
01153-0330-0001
01153-0041-0001
01153-0330-0001
01153-0041-0001
01153-0330-0001
01153-0175-0001
01153-0175-0002
01153-0291-0001
—
01153-0175-0001
01153-0175-0002
01153-0291-0001
—
01153-0175-0001
01153-0175-0002
01153-0291-0001
01153-0234-0001
01153-0277-0001
01153-0038-0001
01153-0277-0001
01153-0038-0001
01153-0277-0001
01153-0038-0001
01153-0350-0002
01153-0373-0001
01153-0350-0002
01153-0373-0001
01153-0350-0002
01153-0373-0001
01153-0294-0001
01153-0294-0001
01153-0294-0001
X
X
X
X
X
NOTE
Kit includes
2 SST O-rings.
Electronics Housing, Austenitic SST
Electronics Cover, Austenitic SST
Cover Wrench
3
1
1
2
Hollow Terminal Block Screw Kit
Solid Terminal Block Screw Kit
(Kit Contains 20 each)
Process Flange, Welded Swagelok
Process Flange, ¼–18 NPT
Process Flange, ¼–18 NPT/¼–18 NPT
Vented Blank Flange
13
See
note
(2)
X
X
X
Valve Stem, 316 SST
Valve Stem and Seat Kit, 316 SST
10
2
X
A
Axial Drain/Vent Valve Kit
Quick Disconnect Axial Drain/Vent Valve Kit
Adjustment Screw Kit
Adjustment Screw(2)
Retaining Ring(2)
O-ring for Adjustment Screw(2)
1
16
18
19
O-ring for Electronics Cover
(Kit contains 20 each)
O-ring for Electronics Cover
(Kit contains 1 each)
2
2
C
01153-0039-0001
01153-0039-0001
01153-0039-0001
2
2
C
01153-0039-0003
01153-0039-0003
01153-0039-0003
O-ring for Process Flange, SST
(Kit contains 6 each)
11
2
B
01153-0249-0001
01153-0249-0001
01153-0249-0001
01153-0053-0001
01153-0248-0001
01153-0329-0001
01153-0053-0001
01153-0248-0001
01153-0329-0001
01153-0053-0001
01153-0248-0001
01153-0329-0001
01153-0333-0001
01153-0333-0001
01153-0333-0001
D.C. 55 O-ring Lubricant (0.25 oz)
D.C. 55 O-ring Lubricant (5.3 oz)
Loctite 580-PST Thread
Sealant (50 ml)
Lubri-Bond A Cover Lubricant (12 oz)
X
Continued on Next Page
6-9
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
Spare Parts Category(3)
Traceable Part
Quantity Required
Item Number
Rosemount
1154DP
Rosemount
1154HP
Rosemount
1154GP
Order No.
Order No.
Order No.
01153-0040-0001
01153-0040-0001
01153-0040-0001
01153-0055-0001
01153-0055-0001
01153-0055-0001
01153-0245-0001
—
—
01153-0245-0001
—
—
01153-0245-0001
01153-0246-0001
01153-0246-0002
01153-0013-0001
01153-0013-0003
01153-0321-0001
01153-0013-0001
01153-0013-0003
01153-0321-0001
01153-0013-0001
01153-0013-0003
01153-0321-0001
Pipe Mount Bracket Kit (Adapters)
Pipe Mount Bracket Kit
(Bracket and Adapters)
01154-0044-0001
01154-0038-0002
01154-0044-0001
01154-0038-0002
01154-0044-0001
01154-0038-0002
Conduit Elbow (M22)
Conduit Elbow (½–14 NPT)
01154-0035-0001
01154-0040-0001
01154-0035-0001
01154-0040-0001
01154-0035-0001
01154-0040-0001
01154-0001-0006
01154-0001-0006
—
Part Description
Electronics Assembly Hardware
Electronics Screw (3)
Nameplate Screw (2)
Locknut
1
A
7
9
Jumper Wire Kit (36 in.)
Bolts and Nuts for Process Flange
Range Codes 4–8 (Pkg of 4)
Range Code 9 (Pkg of 4)
Range Code 10 (Pkg of 4)
(3)
14/8
1
1
1
Panel Mounting Bracket with Bolts
Universal Mounting Bracket with Bolts
Bolts and Washers for Bracket (Pkg of 4)
Amplifier Circuit Board, Output Code R,
N0026(4)
1
6
X
X
X
(1) Rosemount recommends one spare part or kit for every 25 transmitters in Category “A,” one spare part or kit for every
50 transmitters in Category “B,” and one spare part or kit for every 5 transmitters in Category “C.”
(2) Two flanges are required per transmitter. Flange parts depend on desired connection and transmitter type.
(3) Each spare parts kit contains the correct number of nuts, bolts, and washers for the specific transmitter range code it is
designated for. Due to consolidation of parts kits, the bolt length and quantity of washers required may differ from
existing transmitter assemblies and/or parts kits. Verify by part number that the appropriate spare parts kit is used for
the transmitter range code being re-assembled. Contact Rosemount Nuclear Instruments, Inc. if there are questions.
(4) For use with existing N0026 transmitter only.
6-10
Reference Manual
00809-0100-4514, Rev BA
January 2008
SPARE PARTS SHELF
LIFE
Rosemount 1154
Store all spare transmitters and spare component parts in accordance with
ANSI N45.2.2 level B.
Qualified transmitters, spare circuit boards, spare O-rings: the qualified life (as
defined in Qualification Test Report D8400102) plus the shelf life is equal to
the typical design life of the plant (40 years) when the ambient storage
temperature is below 90 °F.
Lubricants and sealant: The date of the end of shelf life (use by date) is
provided with the lubricants and/or sealant, at the time of shipment. The
product has a minimum of six months shelf life at the time
of shipment.
All other parts: Shelf life is not applicable.
IMPORTANT NOTICE
There are factors to consider concerning maintenance of qualification and
traceability during on-site instrument repair because of the nuclear use
intended for these parts. Rosemount Nuclear Instruments, Inc. rigidly
controlled the original assembly of the instrument to ensure that the
specifications were met. Since we are not installing the replacement parts in
the instruments, Rosemount Nuclear Instruments, Inc. is unable to ensure
that the specifications are being satisfied. Replacing parts has
ramifications under 10CFR21, for which the user is responsible. These
same regulations additionally mandate a component traceability program,
which the user must undertake for the replacement parts. In view of this, and
in order to maintain the qualification of the product, the user must ensure that
all replacement parts are installed in accordance with the Rosemount Nuclear
Instruments, Inc. approved installation and calibration procedures herein.
NOTES:
1.
Rosemount 1154 spare parts are not hydrostatic tested or nuclear
cleaned.
2.
Part numbers shown may differ from those currently supplied. The
part numbers shown are current at the time of printing of this manual,
but may be revised in the future. Parts provided are compatible and
interchangeable with those listed on your order as to the form, fit, and
function of the part required. Please adjust your needs accordingly.
6-11
Reference Manual
Rosemount 1154
6-12
00809-0100-4514, Rev BA
January 2008
Reference Manual
00809-0100-4514, Rev BA
January 2008
Rosemount 1154
A
H
Adjustment . . . . . . . . . . . . . . 3-7
zero . . . . . . . . . . . . . . . . 3-7
HIGH LINE PRESSURE . . . . 3-6
Housing
grounding . . . . . . . . . . . 2-5
Process Connectors . . . . . .
Process Flange Reassembly
Process Flange Removal . . .
Purging . . . . . . . . . . . . . . .
. .2-7
. .5-8
. .5-4
. .2-4
B
BOARD CHECKOUT . . . . . . . 5-2
C
Conduit . . . . . . . . . . . . . . . . .
Conduit Connection . . . . . . . .
Conduit Installation . . . . . . . .
Connecting Electrical
Housing to Sensor . . . . . . . . .
Connection, Conduit . . . . . . . .
Connectors, Process . . . . . . .
Correction
zero . . . . . . . . . . . . . . . .
CORRECTION FOR
HIGH LINE PRESSURE . . . . .
Current Control . . . . . . . . . . .
Current Limit . . . . . . . . . . . . .
2-4
2-8
2-8
2-4
2-8
2-6
4-1
5-7
2-8
2-2
Jumper Wire Placement . . . . . 3-4
L
3-7
Level . . . . . . . . . . . . . . 2-4, 6-11
Linearity Adjustment . . . .3-4, 4-3
3-6
4-4
4-4
M
. . . . . . . 3-5
. . . . . . . 4-3
N
. . . 2-3, 2-4
. . . . . . . 5-4
. . . . . . . 2-3
E
Electrical Connection Procedure 2-8
Electrical Considerations
Grounding . . . . . . . . . . . 2-5
Electrical Housing Disassembly 5-6
Electrical Housing Reassembly 5-7
ELECTRICAL INSTALLATION 2-8
Errors
minimizing in
measurements . . 2-4
Exploded View
Rosemount 1154DP . . . . . . . . 5-5
Mounting
location considerations . . 2-2
see also installation
Flow . . . . . . . . . . . . . . . . . . . 2-3
FUNCTIONAL
SPECIFICATIONS . . . . . . . . . 6-4
G
Gas . . . . . . . . . . .
Grounding . . . . . . .
signal wiring . .
transmitter case
. . . . . . . . 2-4
. . . . . . . . 2-5
. . . . . . . . 2-5
. . . . . . . 2-5
Sediment
in impulse tubing . . . . . . .2-3
preventing deposits . . . . .2-3
Signal
terminals . . . . . . . . . . . . .2-8
Span . . . . . . . . . . . . . . . . . . .2-5
Span Adjustment . . . . . . . . . .3-1
Spare Parts Shelf Life . . . . . . 6-11
Swagelok Tube Fittings . . . . . .2-2
installing . . . . . . . . . . . . .2-2
more information about . . .2-3
T
Nuclear Specifications . . . . . . . . 6-1
O
Operation
Current Control . . . . . . . .
Current Limit . . . . . . . . .
Demodulator . . . . . . . . .
Linearity Adjustment . . . .
Oscillator . . . . . . . . . . . .
Reverse Polarity
Protection . . . . .
The ␦-Cell Sensor . . . . . .
Voltage Regulator . . . . . .
Zero and Span
Adjustments . . .
ORDERING INFORMATION .
Oscillator . . . . . . . . . . . . . . .
4-4
4-4
4-3
4-3
4-4
4-4
4-3
4-4
Temperature . . . . . .
storage . . . . . . .
Terminals, Test . . . .
Test Terminals . . . . .
The ␦-Cell Sensor . . .
Torque References . .
Torque Specifications
drain/vent valves
terminal screws .
Traceability . . . . . . .
Transmitter
terminal block . .
Troubleshooting . . . .
. . . 2-3, 2-4
. . . . . . 6-11
. . . . . . .5-2
. . . . . . .5-2
. . . . . . .4-3
. . . . . . .5-9
. . . . . . .2-3
. . . . . . .2-8
. . . . . . 6-11
. . . . . . .2-9
. . . . . . .5-9
V
4-4
6-8
4-4
Vent/Drain valves . . . . . . . . . .2-3
Voltage Regulator . . . . . . . . . .4-4
Z
P
F
Removing Sensor Module
from Electrical Housing . . . . . .5-6
Reverse Polarity Protection . . .4-4
S
J
D
Damping Adjustment
Demodulator . . . . . .
Differential
transmitter . . . .
DISASSEMBLY
PROCEDURE . . . . .
Drain/Vent Valves . .
R
I
Impulse . . . . . . . . . . . . .2-3,
Installation, Conduit . . . . . . . .
Installation, Mechanical . . . . . .
Introduction . . . . . . . . . . . . .
PERFORMANCE
SPECIFICATIONS . . . . . . . . . 6-2
Physical Specifications . . . . . . 6-6
POST-ASSEMBLY TESTS . . . 5-9
Potentiometer . . . . . . . . . . . . 3-8
Process
connections . . . . . . . 2-4, 3-8
loosening and
retightening . 2-3
line . . . . . . . . . . . . . . . . 2-3
taps . . . . . . . . . . . . . . . . 2-4
Zero . . . . . . . . . . . . . . . . . . .3-7
Zero Adjustment . . . . . . . . . . .3-1
Zero and Span Adjustments . . .4-4
Index-1
Reference Manual
Rosemount 1154
Index-2
00809-0100-4514, Rev BA
January 2008
Reference Manual
00809-0100-4514, Rev BA
January 2008
The Emerson logo is a trade mark and service mark of Emerson Electric Co.
Rosemount, the Rosemount logotype, and Alphaline are registered trademarks of Rosemount, Inc.
Cell is a trademarks of Rosemount, Inc.
Swagelok is a registered trademark of Swagelok Co.
Emerson Process Management
Rosemount Nuclear Instruments, Inc.
8200 Market Boulevard
Chanhassen, MN 55317 USA
T (952) 949-5210
F (952) 949-5201
¢00809-XXXX-XXXX ¤
www.rosemountnuclear.com
Rosemount Nuclear Instruments, Inc. satisfies all obligations
coming from legislation to harmonize product requirements in the
European Union.