Emerson 00825-0100-4075 Network Card User Manual

4075_QIG_Rev_BA.fm Page 1 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Smart Wireless THUM™ Adapter
Start
Wireless Considerations
Bench Top Configuration
Step 1: Physical Installation
Step 2: Verify Operation
Reference Information
Product Certifications
EC Declaration of Conformity
End
¢00825-0100-4075[¤
4075_QIG_Rev_BA.fm Page 2 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
© 2010 Rosemount Inc. All rights reserved. All marks property of owner.
Emerson Process Management Rosemount Temperature GmbH Emerson Process Management
Frankenstrasse 21
Rosemount Division
Asia Pacific Private Limited
8200 Market Boulevard
Chanhassen, MN USA 55317
T (US) (800) 999-9307
T (Intnl) (952) 906-8888
F (952) 949-7001
63791 Karlstein
Germany
T 49 (6188) 992 0
F 49 (6188) 992 112
1 Pandan Crescent
Singapore 128461
T (65) 6777 8211
F (65) 6777 0947 / (65) 6777 0743
Enquiries@AP.EmersonProcess.com
IMPORTANT NOTICE
This installation guide provides basic guidelines for the Smart Wireless THUM Adapter. It
does not provide instructions for detailed configuration, diagnostics, maintenance,
service, troubleshooting, or installations. Refer to the THUM Adapter Reference Manual
(document number 00809-0100-4075) for more instruction. The manual and this QIG are
also available electronically on www.rosemount.com.
WARNING
Explosions could result in death or serious injury:
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please
review the Product Certifications section for any restrictions associated with a safe
installation.
• Before connecting a Field Communicator in an explosive atmosphere, ensure the
instruments are installed in accordance with intrinsically safe or non-incendive field
wiring practices.
Electrical shock can result in death or serious injury:
• Avoid contact with the leads and terminals. High voltage that may be present on leads
can cause electrical shock.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions. This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of
7.87-in. (20 cm) from all persons.
IMPORTANT NOTICE
During normal operation, or in fault condition, the THUM Adapter will cause a 2.5 V drop
in the connected loop. It is important to ensure that the power supply can provide at least
2.5 V more than the minimum operating voltage of the wired device to make sure it works
properly with the THUM Adapter installed. To determine the minimum operating voltage
for the wired device, review the wired device operation and installation manual.
2
4075_QIG_Rev_BA.fm Page 3 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
WIRELESS CONSIDERATIONS
Power Up Sequence
Power should not be applied to any wireless device until the Smart Wireless Gateway
(“Gateway”) is installed and functioning properly. Wireless devices should also be powered
up in order of proximity from the Gateway, beginning with the closest. This will result in a
simpler and faster network installation. Enable Active Advertising on the Gateway to ensure
that new devices join the network faster. For more information see the Smart Wireless
Gateway Manual (Doc. No. 00809-0200-4420).
THUM Adapter Position
If possible, the THUM Adapter should be positioned vertically, either straight up or straight
down, and it should be approximately 3 ft. (1 m) from any large structure, building, or
conductive surface to allow for clear communication to other devices. If the THUM Adapter
is mounted horizontally wireless communication range may be decreased. See THUM
Adapter reference manual (00809-0100-4075) for more information.
Figure 1. THUM Adapter Position
Conduit Entry
When installing the THUM Adapter into the conduit entry of a wired device, use an approved
thread sealant. Thread sealant provides a water tight seal. The thread sealant also provides
lubrication to ensure easy removal of the THUM Adapter.
M20 Conduit Adapter
When using the M20 Conduit Adapter on the THUM Adapter, use an approved thread
sealant and tighten wrench tight to the THUM Adapter.
Field Communicator Connections
In order for the Field Communicator to interface with the THUM Adapter, the wired device
must be powered. The Field Communicator must be put into poll mode and should use the
THUM Adapter address of 63.
3
4075_QIG_Rev_BA.fm Page 4 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Power Supply
Minimum loop load of 250 Ohms.
The THUM Adapter communicates via and derives power from a standard 4-20 mA/HART®
loop. The THUM Adapter causes a small voltage drop on the loop which is linear from 2.25
V at 3.5 mA to 1.2 V at 25 mA. Under fault conditions, the maximum voltage drop is 2.5 V.
The THUM Adapter will not affect the 4-20 mA signal under normal or fault conditions as
long as the loop has at least a 2.5 V margin at the maximum loop current (25 mA for a
typical 4-20 mA/HART device).
Limit the power supply to 0.5 Amps maximum, and voltage to 55 Volts DC.
Loop Current
THUM Adapter voltage drop
3.5 mA
25 mA
2.25 V
1.2 V
Load Resistor
If required, add a load resistor as shown in Figure 8, 12, and 16. The resistor should be
adequately rated for the application (1W minimum) and be compatible with the supplied
splice connector which accepts wire sizes from 14 to 22 AWG.
BENCH TOP CONFIGURATION
When performing bench top configuration it is suggested that you connect the THUM
Adapter to a wired device. If this is not possible the following wiring diagrams can be used.
For bench top configuration ensure that the power supply that you are using is limited to 0.5
Amps maximum.
Figure 2. THUM Adapter Only, Powered by a Current Source (Such as a Fluke 744)
THUM Adapter
Green
Ground
Red
+
Black
White
-
Yellow
HART
Modem
4
20 mA
Current
Source
4075_QIG_Rev_BA.fm Page 5 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 3. THUM Adapter Only, Powered by a 24 V Power Supply with 1200 Ohm resistor to limit
current to 20 mA
THUM Adapter
Green
Ground
+
Red
Black
White
-
20 mA
Current
Source
1200
Ohm
Resistor
Yellow
HART
Modem
STEP 1: PHYSICAL INSTALLATION
The THUM Adapter can be installed in one of two configurations:
Direct Mount: The THUM Adapter is connected directly to the conduit entry of the wired
device.
Figure 4. Direct Mount
Direct Mount
1. Install the HART device according to standard installation practices and the
manufacturer’s instructions, being sure to use an approved thread sealant on all
connections.
2. Attach the THUM Adapter to the wired device as shown in Figure 4.
3. Connect the THUM Adapter to the HART wired device using the wiring diagrams below.
See Figures 21, 8, 10, and 12 on the following pages.
4. Close the housing cover on the HART wired device, so that metal touches metal, but do
not over tighten to prevent damaging the unit.
NOTE
Two splice connectors are included with the THUM Adapter. The first is a two
connection splice. The second is a three connection splice for use with a resistor, if
there is not enough resistance in the loop. Both of these splice connectors can
accept 14 to 22 gauge wire. See wired device reference manual for information on the
required loop resistance.
5
4075_QIG_Rev_BA.fm Page 6 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
Smart Wireless THUM Adapter
00825-0100-4075, Rev BA
February 2010
Remote Mount
Remote Mount: The THUM Adapter is mounted separate from the wired device housing
and then connected to the wired device using conduit or other suitable means.
Figure 5. Remote Mount
1. Install the HART device according to standard installation practices and the
manufacturer’s instructions, being sure to use an approved thread sealant on all
connections.
2. The THUM Adapter should be mounted as shown in Figure 5 on page 6.
3. Ground the Remote Mount Kit per local practices.
4. Connect the THUM Adapter to the wired device using standard practices. Wire running
from the THUM Adapter to the wired device should be shielded or in conduit when
installed in electrically noisy environments.
5. Connect the THUM Adapter to the HART wired device using the wiring diagrams below.
See Figure 21, 8, 10, and 12 on the following pages.
6. Close the housing cover on the HART wired device, so that metal touches metal, but do
not over tighten to prevent damaging the unit.
NOTE
Two splice connectors are included with the THUM Adapter. The first is a two
connection splice. The second is a three connection splice for use with a resistor, if
there is not enough resistance in the loop. Both of these splice connectors can
accept 14 to 22 gauge wire. See wired device reference manual for information on the
required loop resistance.
6
4075_QIG_Rev_BA.fm Page 7 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Wiring Diagrams
The following is a list of the figure titles and page numbers for each direct mount and remote
mount wiring diagram:
Figure 6 - Direct Mount Wiring Diagram for 2-Wire Device on page 8
Figure 7 - Remote Mount Wiring Diagram for 2-Wire Device on page 8
Figure 8 - Direct Mount Wiring Diagram for 2-Wire Device with Resistor on page 9
Figure 9 - Remote Mount Wiring Diagram for 2-Wire Device with Resistor on page 9
Figure 10 - Direct Mount Wiring Diagram for 4-Wire Passive Device on page 10
Figure 11 - Remote Mount Wiring Diagram for 4-Wire Passive Device on page 10
Figure 12 - Direct Mount Wiring Diagram for 4-Wire Passive Device with Resistor on
page 11
Figure 13 - Remote Mount Wiring Diagram for 4-Wire Passive Device with Resistor on
page 11
Figure 14 - Direct Mount Wiring Diagram for 4-Wire Active Device on page 12
Figure 15 - Remote Mount Wiring Diagram for 4-Wire Active Device on page 12
Figure 16 - Direct Mount Wiring Diagram for 4-Wire Active Device with Resistor on page 13
Figure 17 - Remote Mount Wiring Diagram for 4-Wire Active Device with Resistor on
page 13
Figure 18 - Direct Mount Wiring Diagram for 4-Wire Active Device with No 4-20 mA Loop on
page 14
Figure 19 - Remote Mount Wiring Diagram for 4-Wire Active Device with No 4-20 mA Loop
on page 14
Figure 20 - THUM Adapter only, Powered by a 24 V Power Supply with 1200 Ohm resistor
to limit current to 20 mA on page 15
Figure 21 - THUM Adapter only, Powered by a 24 V Power Supply with 1200 Ohm resistor
to limit current to 20 mA on page 15
7
4075_QIG_Rev_BA.fm Page 8 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 6. Direct Mount Wiring Diagram for 2-Wire Device
THUM Adapter
Wired Device
Green
Ground
Red
4-20 mA Loop +
Black
4-20 mA Loop -
White
Yellow
Splice Connector
- PWR / COMM
+ PWR / COMM
NOTE:
In order for the THUM Adapter to function properly there must be at least 250 Ohms
resistance in the loop. If the 4–20 mA loop does not have the required resistance, wire
a resistor as shown in Figure 8, 12, or 16 as applicable.
Figure 7. Remote Mount Wiring Diagram for 2-Wire Device
THUM Adapter
Remote Mount Housing
Red
Black
Green
Yellow
4-20 mA Loop +
White
Ground
4-20 mA Loop -
Shield Wire
+ COMM
To Wired Device
- COMM
8
4075_QIG_Rev_BA.fm Page 9 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 8. Direct Mount Wiring Diagram for 2-Wire Device with Resistor
THUM Adapter
Wired Device
Green
Ground
Red
4-20 mA Loop +
Black
4-20 mA Loop -
White
Yellow
Resistor
- PWR / COMM
Splice Connector
+ PWR / COMM
Figure 9. Remote Mount Wiring Diagram for 2-Wire Device with Resistor
THUM Adapter
Remote Mount Housing
Red
Resistor
Black
Green
4-20 mA Loop +
Ground
Yellow
4-20 mA Loop -
White
Shield Wire
+ COMM
To Wired Device
- COMM
9
4075_QIG_Rev_BA.fm Page 10 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 10. Direct Mount Wiring Diagram for 4-Wire Passive Device
THUM Adapter
Wired Device
Green
Splice Connector
Ground
4-20 mA Loop +
Red
4-20 mA Loop -
Black
White
Yellow
Power +
Power+
4-20 mA/HART +
4-20 mA/HART -
Power-
Power -
NOTE:
A passive loop exists when the wired device is not supplying power to the 4–20 mA
loop. It is important to verify if the wired device is operating in active or passive
mode.
Figure 11. Remote Mount Wiring Diagram for 4-Wire Passive Device
THUM Adapter
Remote Mount Housing
Red
Black
Green
Yellow
4-20 mA Loop +
White
4-20 mA Loop -
Ground
Shield Wire
+ COMM
- COMM
10
To Wired Device
4075_QIG_Rev_BA.fm Page 11 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 12. Direct Mount Wiring Diagram for 4-Wire Passive Device with Resistor
THUM Adapter
Wired Device
Green
Splice Connector
4-20 mA Loop +
Ground
Red
4-20 mA Loop -
Black
White
Resistor
Yellow
Power +
Power+
4-20 mA/HART +
4-20 mA/HART -
Power-
Power -
Figure 13. Remote Mount Wiring Diagram for 4-Wire Passive Device with Resistor
THUM Adapter
Remote Mount Housing
Red
Green
Resistor
Black
4-20 mA Loop +
Ground
Yellow
4-20 mA Loop -
White
Shield Wire
+ COMM
To Wired Device
- COMM
11
4075_QIG_Rev_BA.fm Page 12 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 14. Direct Mount Wiring Diagram for 4-Wire Active Device
THUM Adapter
Wired Device
Green
Ground
Splice Connector
4-20 mA Loop +
Yellow
4-20 mA Loop -
White
Black
Red
Power +
4-20 mA/HART -
Power-
4-20 mA/HART +
Power+
Power -
NOTE:
An active loop exists when the wired devices is supplying the power to the 4-20 mA
loop. It is important to verify if the wired device is operating in active or passive
mode.
Figure 15. Remote Mount Wiring Diagram for 4-Wire Active Device
THUM Adapter
Remote Mount Housing
Yellow
Green
White
Red
4-20 mA Loop +
Black
4-20 mA Loop -
Ground
Shield Wire
+ COMM
- COMM
12
To Wired Device
4075_QIG_Rev_BA.fm Page 13 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 16. Direct Mount Wiring Diagram for 4-Wire Active Device with Resistor
THUM Adapter
Wired Device
Green
Splice Connector
Ground
4-20 mA Loop +
Yellow
4-20 mA Loop -
White
Black
Resistor
Red
Power +
Power+
4-20 mA/HART +
4-20 mA/HART -
Power-
Power -
Figure 17. Remote Mount Wiring Diagram for 4-Wire Active Device with Resistor
THUM Adapter
Remote Mount Housing
Yellow
Resistor
White
Green
4-20 mA Loop +
Ground
Red
4-20 mA Loop -
Black
Shield Wire
+ COMM
To Wired Device
- COMM
13
4075_QIG_Rev_BA.fm Page 14 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 18. Direct Mount Wiring Diagram for 4-Wire Active Device with No 4-20 mA Loop
THUM Adapter
Wired Device
Green
Ground
Yellow
Splice Connector
Resistor
White
Black
Red
Power +
Power+
4-20 mA/HART +
4-20 mA/HART -
Power-
Power -
Figure 19. Remote Mount Wiring Diagram for 4-Wire Active Device with No 4-20 mA Loop
THUM Adapter
Remote Mount Housing
Yellow
Green
Resistor
White
Red
Ground
Black
+ COMM
To Wired Device
- COMM
14
4075_QIG_Rev_BA.fm Page 15 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Figure 20. THUM Adapter only, Powered by a 24 V Power Supply with 1200 Ohm resistor to limit
current to 20 mA
THUM Adapter
Ground
Green
Red
Black
White
250
Ohm
Resistor
Yellow
+ 24 V
Power
- Supply
1200
Ohm
Resistor
Junction Box
Figure 21. THUM Adapter only, Powered by a 24 V Power Supply with 1200 Ohm resistor to limit
current to 20 mA
THUM Adapter
Remote Mount
Housing
+
Ground
250 Ohm
Resistor
24 V
Power
- Supply
1200
Ohm
Resistor
15
4075_QIG_Rev_BA.fm Page 16 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Device Network Configuration
In order to communicate with the Smart Wireless Gateway, and ultimately the Information
System, the transmitter must be configured to communicate with the wireless network. This
step is the wireless equivalent of connecting wires from a transmitter to the information
system. Using a Field Communicator or AMS, enter the Network ID and Join Key so that
they match the Network ID and Join Key of the gateway and other devices in the network. If
the Network ID and Join Key are not identical, the THUM Adapter will not communicate with
the network. The Network ID and Join Key may be obtained from the Smart Wireless
Gateway on the Setup>Network>Settings page on the web server, shown in Figure 22.
Figure 22. Gateway Network Settings
AMS
Right click on the THUM Adapter and select Configure. When the menu opens, select Join
Device to Network and follow the method to enter the Network ID and Join Key.
Field Communicator
The Network ID and Join Key may be changed in the wireless device by using the following
Fast Key sequence. Set both Network ID and Join Key.
Function
Wireless Setup
16
Key Sequence
1,4
Menu Items
Smart Power, Network ID, Set Join
Key, Radio State
4075_QIG_Rev_BA.fm Page 17 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Loop Current Test
To verify that the THUM Adapter will work under all conditions, a loop current test should be
performed. This test will exercise the loop under the highest possible voltage drop
conditions.
1. Place loop in manual control.
2. Drive loop to high alarm level. For details see wired device instruction manual.
• When the THUM Adapter is connected to a valve, this will need to be done at the current
source and not from the valve.
• When the THUM Adapter is connected to a transmitter, this will need to be performed at
the transmitter.
3. Place the THUM Adapter into fixed voltage drop mode.
AMS
Right click on the THUM Adapter and select Configure. When the menu opens, select
Manual Setup from the window on the left and select the Wired Device tab on the top.
Make sure that the Time drop down menu at the bottom of the page has Current
selected. Under the Voltage Drop drop down menu in the Smart Power Options box,
select Fixed Voltage Drop. Hit the Apply button to make any changes. See Figure 23 on
page 18.
Field Communicator
When communicating to the THUM Adapter select: Configure - Manual setup - Wired
Device - Voltage Drop Mode. In the method choose Fixed Voltage Drop.
Function
Voltage Drop
Key Sequence
2,2,2,2
Menu Items
Voltage Drop
4. Verify that the current on the loop reaches the high alarm levels.
5. Place the THUM Adapter into variable voltage drop mode.
AMS
Right click on the THUM Adapter and select Configure. When the menu opens, select
Manual Setup from the window on the left and select the Wired Device tab on the top.
Make sure that the Time drop down menu at the bottom of the page has Current
selected. Under the Voltage Drop drop down menu in the Smart Power Options box,
select Variable Voltage Drop. Hit the Apply button to make any changes. See
Figure 23.
Field Communicator
When communicating to the THUM Adapter select: Configure - Manual setup - Wired
Device - Voltage Drop Mode. In the method choose Variable Voltage Drop.
Function
Voltage Drop
Key Sequence
2,2,2,2
Menu Items
Voltage Drop
17
4075_QIG_Rev_BA.fm Page 18 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
Smart Wireless THUM Adapter
6. Remove loop from high alarm value.
Figure 23. AMS Configure screen
18
00825-0100-4075, Rev BA
February 2010
4075_QIG_Rev_BA.fm Page 19 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
STEP 2: VERIFY OPERATION
Operation can be verified in three locations: by using the Field Communicator, at the
Gateway via the Smart Wireless Gateway’s integrated web server, or via AMS™ Wireless
Configurator.
Field Communicator
For HART Wireless transmitter communication, a THUM Adapter DD is required.The Field
Communicator must be put into poll mode using the THUM Adapter address of 63. Use the
wired device documentation to connect the Field Communicator to the THUM Adapter.
Figure 24. Field Communicator Connections
Function
Key Sequence
Communications
3, 3
Menu Items
Join Status, Wireless Mode, Join Mode,
Number of Available Neighbors, Number of
Advertisements Heard, Number of Join
Attempts
Smart Wireless Gateway
If the THUM Adapter was configured with the Network ID and Join Key, and sufficient time
has passed for network polling, the transmitter will be connected to the network. To verify
device operation and connection to the network with the Smart Wireless Gateway’s
integrated web server, open the Smart Wireless Gateway’s integral web interface and
navigate to the Explorer page.
NOTE:
It may take several minutes for the device to join the network.
AMS Wireless Configurator
When the device has joined the network, it will appear in the Wireless Configurator as
illustrated below.
19
4075_QIG_Rev_BA.fm Page 20 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
Smart Wireless THUM Adapter
00825-0100-4075, Rev BA
February 2010
Troubleshooting
If the device is not operating properly, refer to the troubleshooting section of the manual. The
most common cause of incorrect operation is the Network ID and Join Key. The Network ID
and Join Key in the device must match that of the Smart Wireless Gateway.
The Network ID and Join Key may be obtained from the Smart Wireless Gateway on the
Setup>Network>Settings page on the web server. The Network ID and Join Key may be
changed in the wireless device by using the following Fast Key sequence.
Function
Key Sequence
Menu Items
1, 4
Smart Power, Network ID, Set Join
Key, Radio State
Wireless Setup
REFERENCE INFORMATION
NOTE:
In order to communicate with a Field Communicator, the wired device must be
powered.
Table 1. THUM Adapter Fast Key Sequence
Function
Key Sequence
Device Info
2, 2, 4, 3
Guided Setup
2, 1
Manual Setup
2, 2
Wireless
20
2, 2, 1
Menu Items
Manufacturer, Model, Final Assembly Number, Universal,
Field Device, Software, Hardware, Descriptor, Message,
Date, Model Number I, II, III, SI Unit Restriction, Country
Configure, Guided Setup, Join Device to Network,
Configure Update Rate, Zero Trim, Configure Device
Display, Configure Process Alarms
Configure, Manual Setup, Wireless, Pressure, Device
Temperatures, Device Information, Display, Other
Network ID, Join Device to Network, Configure Update
Rate, Configure Broadcast Power Level, Power Mode,
Power Source
4075_QIG_Rev_BA.fm Page 21 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
PRODUCT CERTIFICATIONS
Approved Manufacturing Locations
Rosemount Inc. – Chanhassen, Minnesota, USA
European Directive Information
The EC declaration of conformity for all applicable European directives for this product can
be found at www.rosemount.com. A hard copy may be obtained by contacting an Emerson
Process Management representative.
ATEX Directive (94/9/EC)
Emerson Process Management complies with the ATEX Directive.
Electro Magnetic Compatibility (EMC) (2004/108/EC)
Emerson Process Management complies with the EMC Directive.
Radio and Telecommunications Terminal Equipment Directive (R&TTE)
(1999/5/EC)
Emerson Process Management complies with the R&TTE Directive.
Telecommunication Compliance
All wireless devices require certification to ensure that they adhere to regulations regarding
the use of the RF spectrum. Nearly every country requires this type of product certification.
Emerson is working with governmental agencies around the world to supply fully compliant
products and remove the risk of violating country directives or laws governing wireless
device usage.
FCC and IC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: This device may not cause harmful interference. This device must accept any
interference received, including interference that may cause undesired operation.This
device must be installed to ensure a minimum antenna separation distance of 20 cm from all
persons.
Ordinary Location Certification for FM
As standard, the transmitter has been examined and tested to determine that the design
meets basic electrical, mechanical, and fire protection requirements by FM, a nationally
recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and
Health Administration (OSHA).
21
4075_QIG_Rev_BA.fm Page 22 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
Hazardous Locations Certificates
North American Certifications
Factory Mutual (FM) Approvals
I5 FM Intrinsically Safe and Non-incendive
Intrinsically Safe for Class I/II/III, Division 1, Groups A, B, C, D, E, F, and G.
Zone Marking: Class I, Zone 0, AEx ia llC
Temperature Codes T4 (-50 °C Tamb 70 °C)
Non-incendive for Class I, Division 2, Groups A, B, C, and D.
Intrinsically safe and non-incendive when installed according to Rosemount Drawing
00775-0010.
Enclosure Type 4X/IP66
CSA - Canadian Standards Association
I6 CSA Intrinsically Safe
Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D.
T3C (-50 °C Tamb 70 °C)
Intrinsically safe when installed according to Rosemount Drawing 00775-0012.
Suitable for Class I, Division 2, Groups A, B, C, and D.
Enclosure Type 4X/IP66
European Certifications
I1 ATEX Intrinsic Safety
Certificate No.: Baseefa09ATEX0125X
Ex ia IIC T4 (-50 °C Tamb 70 °C)
IP66
1180
II 1G
Table 2. Input Parameters
Loop Power
Ui = 30V
Ii = 200 mA
Pi = 1.0 W
Ci = 0
Li = 0
Special conditions for safe use (X)
The surface resistivity of the antenna is greater than one gigaohm. To avoid electrostatic
charge build-up, it must not be rubbed or cleaned with solvents or a dry cloth.
The enclosure is made of aluminium alloy and given a protective polyurethane paint
finish; however, care should be taken to protect it from impact or abrasion if located in a
zone 0.
N1 ATEX Type n
Certificate No.: Baseefa09ATEX0131
Ex nA IIC T4 (-50 °C Tamb 70 °C)
Ui = 45 Vdc MAX
IP66
1180
22
II 3 G
4075_QIG_Rev_BA.fm Page 23 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
IECEx Certifications
I7 IECEx Intrinsic Safety
Certificate No.: IECEx BAS 09.0050X
Ex ia IIC T4 (-50 °C Tamb 70°C)
IP66
Table 3. Input Parameters
Loop Power
Ui = 30V
Ii = 200 mA
Pi = 1.0 W
Ci = 0
Li = 0
Special conditions for safe use (X)
The surface resistivity of the antenna is greater than one gigaohm. To avoid electrostatic
charge build-up, it must not be rubbed or cleaned with solvents or a dry cloth.
The enclosure is made of aluminium alloy and given a protective polyurethane paint
finish; however, care should be taken to protect it from impact or abrasion if located in a
zone 0.
N7 IECEx Type n
Certificate No.: IECEx BAS 09.0058
Ex nA IIC T4 (-50 °C Tamb 70°C)
Ui = 45 Vdc MAX
IP66
23
4075_QIG_Rev_BA.fm Page 24 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
EC Declaration of Conformity
No: RMD 1077 Rev. B
We,
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN 55317-6985
USA
declare under our sole responsibility that the product,
Model 775
manufactured by,
Rosemount Inc.
12001 Technology Drive
Eden Prairie, MN 55344-3695
USA
and
8200 Market Boulevard
Chanhassen, MN 55317-9687
USA
to which this declaration relates, is in conformity with the provisions of the European
Community Directives, including the latest amendments, as shown in the attached schedule.
Assumption of conformity is based on the application of the harmonized standards and, when
applicable or required, a European Community notified body certification, as shown in the
attached schedule.
02/10/2010
(signature)
Timothy Layer
(name - printed)
24
(date of issue)
Vice President Global Quality & Customer Care
(function name - printed)
4075_QIG_Rev_BA.fm Page 25 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
EC Declaration of Conformity
No: RMD 1077 Rev. B
EMC Directive (2004/108/EC)
EN 61326-1: 2006
R&TTE Directive (1999/5/EC)
EN 301 489-17: V1.3.2 (2007-6)
EN 61010-1: 2001 (Second Addition)
EN 300 328 V 1.7.1 (2006-10)
ATEX Directive (94/9/EC)
Model 775
Certificate: Baseefa09ATEX0125X
Intrinsically Safe - Group II Category 1 G
Ex ia IIC T4 (Ta =-50°C to +70°C)
Harmonized Standards Used:
EN60079-0:2006; EN60079-11:2007
Certificate: Baseefa09ATEX0131
Type n - Group II Category 3 G
Ex nA IIC T4(Ta =-50°C to +70°C)
Harmonized Standards Used:
EN60079-0:2006; EN60079-15:2005
File ID: 775 CE Marking
Page 2 of 3
K:\prodappr\EUCDOCS\775_RMD1077B.doc
25
4075_QIG_Rev_BA.fm Page 26 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
EC Declaration of Conformity
No: RMD 1077 Rev. B
ATEX Notified Bodies for EC Type Examination Certificate
Baseefa. [Notified Body Number: 1180]
Rockhead Business Park
Staden Lane
Buxton, Derbyshire
SK17 9RZ United Kingdom
ATEX Notified Body for Quality Assurance
Baseefa. [Notified Body Number: 1180]
Rockhead Business Park
Staden Lane
Buxton, Derbyshire
SK17 9RZ United Kingdom
File ID: 775 CE Marking
26
Page 3 of 3
K:\prodappr\EUCDOCS\775_RMD1077B.doc
4075_QIG_Rev_BA.fm Page 27 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
00825-0100-4075, Rev BA
February 2010
Smart Wireless THUM Adapter
27
4075_QIG_Rev_BA.fm Page 28 Friday, February 19, 2010 11:08 AM
Quick Installation Guide
Smart Wireless THUM Adapter
28
00825-0100-4075, Rev BA
February 2010