Specifications | Emerson 1F78H Air Conditioner User Manual

CONTENTS
Installation Instructions for
Preparations .................................................. 1
Thermostat Details ........................................ 1
Removing Old Thermostat ............................ 1
Mounting and Wiring ..................................... 2
Check Thermostat Operation ........................ 3
Configuration Menu ....................................... 4
Specifications ................................................ 5
Troubleshooting ............................................ 5
Heating & Air Conditioning
1F78H
Non-Programmable Thermostat
YOUR THERMOSTAT REPLACES
Typical System Compatibility Chart
1
1F78H
Standard Heat Only Gas or Oil Fired Systems (24 volt)*
Electronic Ignition Heat Only Two Wire Systems (24 volt)*
Yes
Yes
Electronic Ignition Heat Only Gas or Oil Fired Systems (24 volt)*
Standard Heat/Cool Systems (24 volt)*
Yes
Yes
Heat/Cool Systems Electric Heat (24 volt)*
Heat Only Electric Heat Systems (24 volt)*
Cool Only Systems (24 volt)*
Heat Pump Systems (No Aux or Emergency Heat)*
Hot Water Zone Heat Only Systems
Hot Water Zone Heat Only (Three Wire) Systems
Line Voltage Heating or Baseboard 110/240 Volt Systems
Millivolt Systems Floor or Wall Furnaces
12 VDC Mobile Home Application
Multistage Systems
Systems Exceeding 30VAC, 1.5 Amp
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
PREPARATIONS
Assemble tools required as shown below.
FLAT BLADE SCREWDRIVER
WIRE CUTTER/STRIPPER
HAND OR POWER
DRILL WITH 3/16 INCH
DRILL BIT, IF NEEDED
SPIRIT LEVEL OR PLUMB BOB AND LINE OPTIONAL—
THERMOSTAT DOES NOT NEED TO BE LEVEL TO WORK PROPERLY
Failure to follow and read all instructions carefully
before installing or operating this control could cause
personal injury and/or property damage
* Requires common wire for 24VAC at the thermostat
2
THERMOSTAT DETAILS
3
REMOVING OLD THERMOSTAT
! CAUTION
Mounting
hole
To prevent electrical shock and/or equipment damage,
disconnect electrical power to the system at the main
fuse or circuit breaker until installation is complete.
W
Mounting
hole
W905
Clip for
Hydronic
System
RH
C
G
W904
W905
ELEC GAS
W904
Clip for
Celsius Display
Electric/Gas
Switch
Figure 1. Thermostat base
WHITE-RODGERS
EMERSON ELECTRIC CO.
9797 REAVIS ROAD
ST. LOUIS, MISSOURI 63123-5398
www.white-rodgers.com
B
O
RC
Y
Before removing wires from old thermostat’s switching subbase,
label each wire with the terminal designation it was removed from.
1. Remove Old Thermostat: A standard heat/cool thermostat
consists of three basic parts:
a. The cover, which may be either a snap-on or hinge type.
b. The base, which is removed by loosening all captive screws.
c. The switching subbase, which is removed by unscrewing
the mounting screws that hold it on the wall or adaptor plate.
2. Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
3. Remove the front cover of the old thermostat. With wires still
attached, remove wall plate from the wall. If the old thermostat
has a wall mounting plate, remove the thermostat and the wall
mounting plate as an assembly.
4. Identify each wire attached to the old thermostat.
5. Disconnect the wires from the old thermostat one at a time.
DO NOT LET WIRES FALL BACK INTO THE WALL.
6. Install new thermostat using the following procedures.
PART NO. 37-6450A
Printed in U.S.A.
0247
3
REMOVING OLD THERMOSTAT
! CAUTION
CONTINUED FROM FIRST PAGE
ATTENTION! This product does not contain mercury. However, this product may replace a unit which contains mercury.
Do not open mercury cells. If a cell becomes damaged, do not
touch any spilled mercury. Wearing non-absorbent gloves, take
up the spilled mercury and place into a container which can be
sealed. If a cell becomes damaged, the unit should be discarded.
Mercury must not be discarded in household trash. When the unit
this product is replacing is to be discarded, place in a suitable
container and return to White-Rodgers at 2892 Harrison Street,
Batesville, AR 72501-2117 for proper disposal.
4
MOUNTING AND WIRING
!
Take care when securing and routing wires so they do
not short to adjacent terminals or rear of thermostat.
Personal injury and/or property damage may occur.
TERMINAL CROSS REFERENCE CHART
New Thermostat
Terminal Designation
RH
Other Manufacturers’
Terminal Designation
*
4
RH
M
R
RC
R
R
V
-
G
G
G
F
G
W
W
W
H
W
Y
Y
Y
C
Y
C
C
C
X
C
* Factory installed jumper wire between the RH
and RC terminals must remain in place.
WARNING
Do not use on circuits exceeding specified voltage.
Higher voltage will damage control and could cause
shock or fire hazard.
Do not short out terminals on gas valve or primary
control to test. Short or incorrect wiring will damage
thermostat and could cause personal injury and/or
property damage.
Thermostat installation and all components of the system shall conform to Class II circuits per the NEC code.
Electric Heat or Single-Stage
Heat Pump Systems
This thermostat is configured from the factory to operate a heat/
cool, fossil fuel (gas, oil, etc.), forced air system. It is configured
correctly for any system that DOES NOT require the thermostat
to energize the fan on a call for heat. If your system is an electric
or heat-pump system that REQUIRES the thermostat to turn on
the fan on a call for heat, locate the GAS/ELECTRIC switch (see
fig. 1) and switch it to the ELECTRIC position. This will allow the
thermostat to energize the fan immediately on a call for heat. If you
are unsure if the heating/cooling system requires the thermostat
to control the fan, contact a qualified heating and air conditioning
service person.
Attach Thermostat Base to Wall
1. Remove the packing material from the thermostat. Gently pull
the cover straight off the base. Forcing or prying on the
thermostat will cause damage to the unit. If necessary, move
the electric heat switch (see ELECTRIC HEAT SYSTEMS,
above).
2. Connect wires beneath terminal screws on base using appropriate wiring schematic (see figs. 2 through 7).
3. Place base over hole in wall and mark mounting hole locations
on wall using base as a template.
4. Move base out of the way. Drill mounting holes.
5. Fasten base loosely to wall, as shown in fig. 1, using two
mounting screws. Place a level against bottom of base, adjust
until level, and then tighten screws. (Leveling is for appearance only and will not affect thermostat operation.) If you are
using existing mounting holes, or if holes drilled are too large
and do not allow you to tighten base snugly, use plastic screw
anchors to secure subbase.
6. Push excess wire into wall and plug hole with a fire-resistant
material (such as fiberglass insulation) to prevent drafts from
affecting thermostat operation.
Hydronic (Hot Water or Steam)
Heating Systems
This thermostat is set to operate properly with a forced-air heating
system. If you have a hydronic heating system (a system that
heats with hot water or steam), you must set the thermostat to
operate properly with your system by changing the first option in
the configuration menu to SL (see configuration menu, page 5).
www.white-rodgers.com
4
MOUNTING AND WIRING
CONTINUED FROM SECOND PAGE
JUMPER
WIRE
THERMOSTAT
C
B
Y
G
W
Cooling
System
Fan
Relay
Heating
System
O
RC
RH
THERMOSTAT
C
B
Y
O
G
W
RC
SYSTEM
RH
SYSTEM
NOTE
Fan
Relay
For Heat only,
attach to RH and W
Heating
System
Hot
24 VAC
120 VAC
Neutral
Hot
24 VAC
HEATING
TRANSFORMER
120 VAC
Neutral
Hot
TRANSFORMER
24 VAC
120 VAC
Neutral
Figure 2. Typical wiring diagram for
heat only, 4-wire, single transformer systems
COOLING TRANSFORMER
Figure 5. Typical wiring diagram for
heat/cool, 6-wire, two-transformer systems
JUMPER
WIRE
THERMOSTAT
C
B
O
Y
G
W
RC
RH
SYSTEM
Cooling
System
JUMPER
WIRE
JUMPER
WIRE
THERMOSTAT
Fan
Relay
C
Hot
24 VAC
B
Y
O
G
W
RC
RH
SYSTEM
120 VAC
Reversing Compressor Fan
Valve*
Contactor Relay
Neutral
TRANSFORMER
Hot
24 VAC
Figure 3. Typical wiring diagram for
cool only, 4-wire, single transformer systems
* Reversing valve is energized when the
system switch is in the COOL position
Figure 6. Typical wiring diagram for heat pump
with reversing valve energized in COOL
NOTE
RED jumper wire (provided with thermostat) must be
connected between thermostat RH and RC terminals
for proper thermostat operation with this system.
JUMPER
WIRE
JUMPER
WIRE
THERMOSTAT
C
B
O
Y
G
W
RC
Fan
Relay
Heating
System
C
O
Y
G
W
RC
RH
SYSTEM
Compressor Fan
Contactor Relay
* Reversing valve is energized when the
system switch is in the HEAT position
TRANSFORMER
Hot
24 VAC
120 VAC
Neutral
120 VAC
Neutral
TRANSFORMER
Figure 7. Typical wiring diagram for heat pump
with reversing valve energized in HEAT
Figure 4. Typical wiring diagram for
heat/cool, 5-wire, single transformer systems
5
B
Reversing
Valve*
Hot
24 VAC
JUMPER
WIRE
THERMOSTAT
RH
SYSTEM
Cooling
System
120 VAC
Neutral
TRANSFORMER
CHECK THERMOSTAT OPERATION
NOTE
To prevent static discharge problems, touch side of thermostat to release static build-up before touching any keys.
If at any time during testing your system does not operate
properly, contact a qualified serviceperson.
Fan Operation
If your system does not have a G terminal connection, skip to
Heating System.
1. Turn on power to the system.
2. Move fan switch to ON position. The blower should begin to
operate.
3. Move fan switch to AUTO position. The blower should stop
immediately.
Cooling System
! CAUTION
To prevent compressor and/or property damage, if the
outdoor temperature is below 50°F, DO NOT operate the
cooling system.
This thermostat has a time delay between cooling cycles to allow
the head pressure in the compressor to stabilize. If the temperature is adjusted to call for cool within 5 minutes of the last cycle the
snowflake icon will blink indicating the thermostat is locked out.
After 3 to 5 minutes, the compressor will start and the snowflake
icon will stop flashing. This helps prevent the compressor from
cycling too quickly and is normal operation for the thermostat.
1. Move SYSTEM switch to COOL position.
2. Press
to adjust thermostat setting below room temperature. The blower should come on immediately on high speed,
followed by cold air circulation
3. Press
to adjust temperature setting above room temperature. The cooling system should stop operating.
Heating System
1. Move SYSTEM switch to HEAT position. If the heating system
has a standing pilot, be sure to light it.
2. Press
to adjust thermostat setting above room temperature. The heating system should begin to operate.
3. Press
to adjust temperature setting below room temperature. The heating system should stop operating.
www.white-rodgers.com
5
CHECK THERMOSTAT OPERATION
CONTINUED FROM THIRD PAGE
1
Before you begin using your thermostat, you should be familiar
with its features and with the display and the location and
operation of the thermostat buttons. Your thermostat consists of
two parts: the thermostat cover and the base. To remove the
cover, gently pull it straight out from the base. To replace the
cover, line up the cover with the base and press gently until the
cover snaps onto the base.
2
WHITE-RODGERS
The Thermostat Buttons and Switches
FAN
SYSTEM
ON AUTO COOL OFF HEAT
1 (Up arrow) Raises temperature setting.
2 (Down arrow) Lowers temperature setting.
3
3 FAN switch (ON, AUTO).
4
4 SYSTEM switch (COOL, OFF, HEAT).
The Display
5
6
7
is displayed when the SYSTEM switch is in the HEAT
position.
is displayed (non-flashing) when the SYSTEM
switch is in the COOL position.
is displayed (flashing)
when the compressor is in lockout mode.
5
6 Displays current temperature.
Figure 8. Thermostat display, buttons, and switches
7 Displays currently set temperature (this is blank when
SYSTEM switch is in the OFF position).
6
Operating Features
Now that you are familiar with the thermostat buttons and display,
read the following information to learn about the many features of
the thermostat.
• SIMULTANEOUS HEATING/COOLING SETPOINT
STORAGE — You can enter both your heating and cooling
setpoints at the same time. There is no need to re-enter the
thermostat at the beginning of each season.
• TEMPERATURE SETTING — Press
or
until the
display shows the temperature you want. The thermostat will
keep the room temperature at the selected temperature.
• °F/°C CONVERTIBILITY — The factory default setting is
Fahrenheit. If you need Celsius temperature setting, go to
menu mode and change the fifth option to C (see configuration menu, page 5).
• TEMPERATURE DISPLAY ADJUSTMENT — Your new
thermostat has been accurately set in our factory. However,if
you wish, you may adjust your new thermostat temperature
display to match your old thermostat. This can be accomplished (within a ±4° range) by going into the menu mode (see
configuration menu, page 5).
CONFIGURATION MENU
The configuration menu allows you to set certain thermostat operating characteristics to your system or personal requirements.
With the system switch in “OFF” mode, press
and
keys
at the same time to enter the configuration menu. The display will
show the first item in the configuration menu.
The configuration menu table summarizes the configuration
options. An explanation of each option follows.
Press
and
together momentarily to change to the next
menu item. To exit the menu, change the system switch from OFF
to HEAT or COOL. If no action is taken within fifteen minutes, the
thermostat will revert to normal operation.
2) Select FA or SL (Fast or Slow) Heating Cycle Rate—The
FA setting is frequently used for gas, oil or electric heat. The
SL setting produces a longer heating cycle which is normally
for hot water or steam (hydronic) systems. Both settings
produce very accurate temperature control and can be set to
your personal preference. FA cycles the system just under
1°F and the SL setting cycles at approximately 1.5F°.
3) Not Available
4) Select Compressor Lockout LOC OFF or ON—Selecting
LOC ON will cause the thermostat to wait 5 minutes before
turning on the compressor if the heating and cooling system
loses power. It will also wait 5 minutes minimum between
cooling cycles. This is intended to help protect the compressor from short cycling. Some newer compressors already
www.white-rodgers.com
Configuration Menu
Step
Press Button(s)
1
Set system switch
to OFF
2
6)
8
Press
or
Comments
to select:
System switch must be OFF to configure thermostat
and
(FA)
SL
3
and
d-L (ON)
OFF
N/A
4
and
LOC (OFF)
ON
Select compressor lockout OFF or ON
5
and
0 HI (0)
4 LO to 4 HI
6
and
(F)
C
7
Move system
switch from OFF
to HEAT or COOL
* Press
5)
Displayed (Factory Default)
and
Select FA or SL (Fast or Slow) heating cycle rate
Select temperature display adjustment higher or lower
Select temperature display to F or C
Returns to normal operation
simultaneously to advance to next item
have a time delay built in and do not require this feature. Your
compressor manufacturer can tell you if the feature is already
present in their system. When the compressor time delay
for about five minutes then turn on
occurs it will flash the
the compressor.
Select Temperature Display Adjustment 4 LO to 4 HI—
Allows you to adjust the room temperature display 4° higher
or lower. Your thermostat was accurately calibrated at the
factory but you have the option to change the display temperature to match your previous thermostat.
Select F° or C° Readout—Changes the display readout to
Centigrade or Fahrenheit as required.
7
SPECIFICATIONS
ELECTRICAL DATA
Electrical Rating:
20 to 30 VAC 50/60 Hz.
0.05 to 1.2 Amps (Load per terminal)
1.5 Amps Maximum Total Load (All terminals combined)
THERMAL DATA
Setpoint Temperature Range: 45°F to 90°F (7°C to 32°C)
Operating Ambient Temperature Range: 32°F to 105°F
Operating Humidity Range: 0 to 90% RH (non-condensing)
Shipping Temperature Range: -40°F to 150°F
TROUBLESHOOTING
Symptom
Possible Cause
Corrective Action
No Heat/No Cool/No Fan
(common problems)
1. Blown fuse or tripped circuit breaker.
2. Furnace power switch to OFF.
3. Furnace blower compartment door or
panel loose or not properly installed.
Replace fuse or reset breaker.
Turn switch to ON.
Replace door panel in proper position to engage
safety interlock or door switch.
No Heat
1. Pilot light not lit.
2. System Switch not set to Heat.
Re-light pilot.
Set System Switch to Heat and raise temperature
above room temperature.
Verify thermostat and system wires are securely
attached.
Many furnaces have safety devices that shut down
when a lock-out condition occurs. If the heat works
intermittently contact the furnace manufacturer or
local service person for assistance.
Diagonistic: Set System Switch to Heat and raise
the setpoint above room temperature. Within a few
seconds the thermostat should make a soft click
sound. This sound usually indicates the thermostat is operating properly. If the thermostat does
not click on, contact your heating and cooling
service person or place of purchase for a
replacement. If the thermostat clicks, contact the
furnace manufacturer or a service person to verify
the heating is operating correctly.
3. Loose connection to thermostat or system.
4. Furnace Lock-Out Condition. Heat may also
be intermittent.
5. Heating system requires service or
thermostat requires replacement.
www.white-rodgers.com
8
TROUBLESHOOTING
Symptom
Possible Cause
Corrective Action
No Cool
1. System Switch not set to Cool.
Set System Switch to Cool and lower temp below
room temp.
Verify thermostat and system wires are securely
attached.
Same procedure as diagnostic for No Heat
condition except set the thermostat to Cool and
lower the setpoint below the room temperature.
There may be up to a five minute delay before the
thermostat clicks in Cooling.
2. Loose connection to thermostat or system.
3. Cooling system requires service or
thermostat requires replacement.
Heat, Cool or Fan Runs Constantly.
1. Possible short in wiring.
2. Possible short in thermostat.
3. Possible short in heat/cool/fan system.
4. Fan Switch set to Fan On.
Check each wire connection to verify they are not
shorted or touching together. No bare wire should
stick out from under terminal screws. If the
condition persists the manufacturer of your
system or service person can instruct you on how
to test the Heat/Cool system for correct operation.
If the system operates correctly, replace the
thermostat.
Furnace Cycles Too Fast or Too Slow
(narrow or wide temperature swing)
1. The location of the thermostat and/or the
size of the Heating System may be
influencing the cycle rate.
Digital thermostats normally provide precise
temperature control and may cycle faster than
some older mechanical models. A faster cycle
rate means the unit turns on and off more
frequently but runs for a shorter time so there is
no increase in energy use. If you would like to
increase the cycle time, go to menu mode as
mentioned in the instructions for Hydronic Heating
Systems. It is not possible to shorten the cycle
time. If an acceptable cycle rate is not achieved as
received or by changing cycle time from FAST to
SLOW on the menu mode contact a local
service person for additional suggestions.
Cooling Cycles Too Fast or Too Slow
(narrow or wide temperature swing)
1. The location of the thermostat and the size
of the Cooling System can influence the
cycle rate.
The cycle rate for cooling is fixed and can not be
adjusted. Contact a local service person for
suggestions.
Thermostat Setting and Thermostat
Thermometer Disagree
1. Thermostat thermometer setting requires
adjustment.
The thermometer can be adjusted +/- 4 degrees.
See Temperature Display Adjustment in the
Operation section.
Blank Display and/or Keypad
Not Responding
1. Thermostat loss of power
2. Voltage spike or static discharge.
Check possible blown fuse or tripped breaker.
Turn the system power off. Wait for 5 minutes and
turn the power on.
www.white-rodgers.com
Download PDF

advertising