Emerson 3000 Oxygen Equipment User Manual

Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
Oxygen Analyzer with HPS Heater
Power Supply Field Module
(for use with Existing Signal
Conditioning Electronics)
http://www.processanalytic.com
ESSENTIAL INSTRUCTIONS
READ THIS PAGE BEFORE PROCEEDING!
Rosemount Analytical designs, manufactures and tests its products to meet many national and
international standards. Because these instruments are sophisticated technical products, you
MUST properly install, use, and maintain them to ensure they continue to operate within their
normal specifications. The following instructions MUST be adhered to and integrated into your
safety program when installing, using, and maintaining Rosemount Analytical products. Failure to
follow the proper instructions may cause any one of the following situations to occur: Loss of life;
personal injury; property damage; damage to this instrument; and warranty invalidation.
• Read all instructions prior to installing, operating, and servicing the product.
• If you do not understand any of the instructions, contact your Rosemount Analytical representative for clarification.
• Follow all warnings, cautions, and instructions marked on and supplied with the product.
• Inform and educate your personnel in the proper installation, operation, and maintenance of the product.
• Install your equipment as specified in the Installation Instructions of the appropriate Instruction Manual and per applicable local and national codes. Connect all products to the
proper electrical and pressure sources.
• To ensure proper performance, use qualified personnel to install, operate, update, program,
and maintain the product.
• When replacement parts are required, ensure that qualified people use replacement parts
specified by Rosemount. Unauthorized parts and procedures can affect the product’s performance, place the safe operation of your process at risk, and VOID YOUR WARRANTY.
Look-alike substitutions may result in fire, electrical hazards, or improper operation.
• Ensure that all equipment doors are closed and protective covers are in place, except
when maintenance is being performed by qualified persons, to prevent electrical shock
and personal injury.
The information contained in this document is subject to change without notice.
Emerson Process Management
Rosemount Analytical Inc.
Process Analytic Division
1201 N. Main St.
Orrville, OH 44667-0901
T (330) 682-9010
F (330) 684-4434
e-mail: gas.csc@EmersonProcess.com
http://www.processanalytic.com
HIGHLIGHTS OF CHANGES
Effective October, 1995 Rev. 3
Page
Summary
Page 1-1
Updated art to reflect new probe configuration.
Page 1-3
Updated art to reflect new probe configuration.
Page 1-4
Updated art to reflect new probe configuration.
Page 2-1
Update installation procedure to include optional ceramic diffusor and
vee deflector.
Page 2-2
Updated art and dimensions to reflect new probe configurations.
Page 2-3
Updated art and dimensions to reflect new probe configurations.
Page 2-8
Updated art and dimensions to reflect new probe configurations.
Effective June, 1996 Rev. 3.1
Page
Summary
Page 1-3
Added ambient air note.
Page 2-3
Updated Probe Installation, Figure 2-1, sheets 1 and 2 of 5.
Effective January, 1997 Rev. 3.2
Page
Summary
Page iii
Added "Safety instructions for the wiring and installation of this
apparatus".
Page 2-1
Added one WARNING to read new safety instructions and another
WARNING regarding protective covers and grounds.
Page 2-9
Added WARNING regarding protective covers and grounds and added
NOTE regarding HPS fuse locations and specifications.
Page 2-11
Added NOTE regarding HPS fuse specifications to Figure 2-7.
Page 3-1
Added WARNING regarding protective covers and grounds.
Page 4-1
Added WARNING regarding protective covers and grounds.
Page 7-1
Added fuses to index listing.
Effective May, 1997 Rev. 3.3
Page
Summary
Page P-2
Added safety sheets.
Effective February, 1998 Rev. 3.4
Page
Summary
Page 2-2
Figure 2-1. Changed calibration gas tube dimensions.
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
TABLE OF CONTENTS
PREFACE......................................................................................................................... P1
Definitions ......................................................................................................................... P1
Safety Instructions ........................................................................................................... P2
1-0
1-1
1-2
DESCRIPTION ................................................................................................................ 1-1
Component Checklist of Typical System (Package Contents)........................................ 1-1
Overview.......................................................................................................................... 1-1
2-0
2-1
2-2
INSTALLATION .............................................................................................................. 2-1
Oxygen Analyzer (Probe) Installation .............................................................................. 2-1
Heater Power Supply Installation .................................................................................... 2-9
3-0
3-1
3-2
3-3
3-4
3-5
SETUP............................................................................................................................. 3-1
Overview.......................................................................................................................... 3-1
Models 218, 225, and 132 (Analog) Electronics Setup .................................................. 3-1
Model 218A Electronics Setup ....................................................................................... 3-2
Model TC200 VERITRIM Electronics Setup.................................................................... 3-3
Model 132 Digital Electronics Setup................................................................................ 3-4
4-0
4-1
4-2
TROUBLESHOOTING .................................................................................................... 4-1
Overview.......................................................................................................................... 4-1
System Troubleshooting.................................................................................................. 4-1
5-0
RETURN OF MATERIAL .............................................................................................. 5-1
6-0
APPENDICES ................................................................................................................. 6-1
7-0
INDEX.............................................................................................................................. 7-1
Rosemount Analytical Inc.
A Division of Emerson Process Management
i
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
LIST OF ILLUSTRATIONS
Figure 1-1.
Figure 1-2.
Figure 1-3.
Figure 2-1.
Figure 2-2.
Figure 2-3.
Figure 2-4.
Figure 2-5.
Figure 2-6.
Figure 2-7.
Figure 3-1.
Figure 3-2.
Figure 3-3.
Figure 3-4.
ii
Typical System Package ....................................................................................... 1-1
Typical System Installation .................................................................................... 1-3
Typical System Wiring ........................................................................................... 1-4
Probe Installation ................................................................................................... 2-2
Orienting the Optional Vee Deflector ..................................................................... 2-7
Outline of Heater Power Supply ............................................................................ 2-7
Electrical Installation of Heater Power Supply....................................................... 2-8
Heater Power Supply Wiring Connections ............................................................ 2-9
Jumper Selection Label ....................................................................................... 2-10
Jumpers on HPS Mother Board........................................................................... 2-11
Temperature Controller Card Calibration Points ................................................... 3-1
Main PCB (Model 218A) EPROM Replacement ................................................... 3-2
Main PCB (Model TC200) EPROM Replacement ................................................. 3-3
Main PCB (Model 132) EPROM Replacement...................................................... 3-4
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
!
CAUTION
If the HPS 3000 and World Class 3000 probe are used with any of the following model
electronics; 218, 225, 218A, and TC200, read appropriate set point adjustment in Instruction
Bulletin (IB) 106-300NE to prevent damage to the World Class 3000 probe.
PREFACE
The purpose of this manual is to provide information concerning the components, functions, installation and maintenance of this particular oxygen analyzer.
Some sections may describe equipment not used in your configuration. The user should
become thoroughly familiar with the operation of this module before operating it. Read
this instruction manual completely.
DEFINITIONS
The following definitions apply to WARNINGS, CAUTIONS, and NOTES found throughout this
publication.
Highlights an operation or maintenance
procedure, practice, condition, statement, etc. If not strictly observed, could
result in injury, death, or long-term
health hazards of personnel.
Highlights an operation or maintenance
procedure, practice, condition, statement, etc. If not strictly observed, could
result in damage to or destruction of
equipment, or loss of effectiveness.
NOTE
Highlights an essential operating procedure,
condition, or statement.
: EARTH (GROUND) TERMINAL
: PROTECTIVE CONDUCTOR TERMINAL
: RISK OF ELECTRICAL SHOCK
: WARNING: REFER TO INSTRUCTION BULLETIN
NOTE TO USERS
The number in the lower right corner of each illustration in this publication is a manual illustration number. It is not a part number, and is not related to the illustration in any technical
manner.
Rosemount Analytical Inc.
A Division of Emerson Process Management
P-1
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
IMPORTANT
SAFETY INSTRUCTIONS
FOR THE WIRING AND INSTALLATION
OF THIS APPARATUS
The following safety instructions apply specifically to all EU member states. They should
be strictly adhered to in order to assure compliance with the Low Voltage Directive. NonEU states should also comply with the following unless superseded by local or National
Standards.
1. Adequate earth connections should be made to all earthing points, internal and external,
where provided.
2. After installation or troubleshooting, all safety covers and safety grounds must be replaced.
The integrity of all earth terminals must be maintained at all times.
3. Mains supply cords should comply with the requirements of IEC227 or IEC245.
4. All wiring shall be suitable for use in an ambient temperature of greater than 75°C.
5. All cable glands used should be of such internal dimensions as to provide adequate cable
anchorage.
6. To ensure safe operation of this equipment, connection to the mains supply should only be
made through a circuit breaker which will disconnect all circuits carrying conductors during a
fault situation. The circuit breaker may also include a mechanically operated isolating switch.
If not, then another means of disconnecting the equipment from the supply must be provided
and clearly marked as such. Circuit breakers or switches must comply with a recognized
standard such as IEC947. All wiring must conform with any local standards.
7. Where equipment or covers are marked with the symbol to the right, hazardous voltages are likely to be present beneath. These covers should only be
removed when power is removed from the equipment — and then only by
trained service personnel.
8. Where equipment or covers are marked with the symbol to the right, there is a
danger from hot surfaces beneath. These covers should only be removed by
trained service personnel when power is removed from the equipment. Certain surfaces may remain hot to the touch.
9. Where equipment or covers are marked with the symbol to the right, refer to
the Operator Manual for instructions.
10. All graphical symbols used in this product are from one or more of the following standards: EN61010-1, IEC417, and ISO3864.
P-2
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 1
DESCRIPTION
1-1
COMPONENT CHECKLIST OF TYPICAL
SYSTEM (PACKAGE CONTENTS)
A typical Rosemount World Class 3000 Oxygen
Analyzer with HPS 3000 Heater Power Supply
package should contain the items shown in
Figure 1-1. Record the Part Number, Serial
Number, and Order Number for each
component of your system in the table located
on the first page of this manual.
The Heater Power Supply allows the
World Class 3000 Oxygen Analyzer (Probe)
to be interfaced to a number of different and
earlier model electronic packages. These
electronic packages are not covered in this
manual. For specific information concerning
calibration and operation of the system,
refer to the Instruction Bulletin applicable to
your electronics package.
b. System Description
1-2
OVERVIEW
a. Scope
This Instruction Bulletin has been designed
to supply details needed to install, start up,
and troubleshoot the Rosemount World
Class 3000 Oxygen Analyzer with HPS
3000 Heater Power Supply Field Module.
The Rosemount Oxygen Analyzer (Probe) is
designed to measure the net concentration
of oxygen in an industrial process; i.e., the
oxygen remaining after all fuels have been
oxidized. The probe is permanently positioned within an exhaust duct or stack and
performs its task without the use of a sampling system.
4
3
2
1.
2.
3.
4.
Oxygen Analyzer (Probe)
Heater Power Supply
Instruction Bulletin
Mounting Adaptor Plate
with Mounting Hardware
and Gasket
1
19260001
Figure 1-1. Typical System Package
Rosemount Analytical Inc.
A Division of Emerson Process Management
Description
1-1
1
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
The equipment measures oxygen percentage by reading the voltage developed
across a heated electrochemical cell, which
consists of a small yttria-stabilized, zirconia
disc. Both sides of the disc are coated with
porous metal electrodes. When operated at
the proper temperature, the millivolt output
voltage of the cell is given by the following
Nernst equation:
EMF = KT log10(P1/P2) + C
Where:
1. P2 is the partial pressure of the oxygen
in the measured gas on one side of the
cell,
2. P1 is the partial pressure of the oxygen
in the reference gas on the other side,
3. T is the absolute temperature,
4. C is the cell constant,
5. K is an arithmetic constant.
NOTE
For best results, use clean, dry,
instrument air (20.95% oxygen) as a
reference gas.
When the cell is at operating temperature
and there are unequal oxygen concentrations across the cell, oxygen ions will travel
from the high partial pressure of oxygen
side to the low partial pressure side of the
cell. The resulting logarithmic output voltage
is approximately 50 mV per decade. Because the magnitude of the output is proportional to the logarithm of the inverse of
the sample of the oxygen partial pressure,
the output signal increases as the oxygen
concentration of the sample gas decreases.
This characteristic enables the oxygen
analyzer to provide exceptional sensitivity at
low oxygen concentrations.
Oxygen analyzer equipment measures net
oxygen concentration in the presence of all
the products of combustion, including water
vapor. Therefore, it may be considered an
analysis on a "wet" basis. In comparison
with older methods, such as the Orsat apparatus, which provides an analysis on a
"dry" gas basis, the "wet" analysis will, in
general, indicate a lower percentage of
1-2
Description
oxygen. The difference will be proportional
to the water content of the sampled gas
stream.
c. System Configuration
The equipment discussed in this manual
consists of two major components; the oxygen analyzer (probe), and the heater power
supply.
Probes are available in five length options,
giving the user the flexibility to use an in situ
penetration appropriate to the size of the
stack or duct. The options on length are 18
inches (457 mm), 3 feet (0.91 m), 6 feet
(1.83 m), 9 feet (2.74 m), or 12 feet
(3.66 m).
The heater power supply (HPS) provides an
interface to the electronics package and
contains a transformer for supplying proper
voltage to the 44 Vac and 115 Vac probe
heaters. The enclosure has been designed
to meet NEMA 4X (IP56) specifications for
water tightness; an optional enclosure to
meet Class 1, Division 1, Group B (IP56)
explosion-proof is also available.
The oxygen analyzer is connected to the
HPS and electronics package using seven
wires housed within the connecting system
cable.
d. Features
1. Unique and patented cell protection
action that automatically protects
sensor cell when analyzer detects
reducing atmospheres.
2. Output voltage and sensitivity increase
as the oxygen concentration
decreases.
3. In situ, non-sampling analyzer.
4. Field replaceable cell.
5. Analyzer constructed of rugged 316
LSS for all wetted parts.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
6. Suitable for use in temperatures up to
1300°F (700°C).
A typical installation is illustrated in Figure
1-2 and Figure 1-3.
7. Heater power supply allows World
Class 3000 probe to be interfaced with
existing analog and 218A digital
electronic packages.
After selecting the probe mounting location,
provision should be made for a platform
where the probe can be easily serviced.
The heater power supply can be located up
to 150 feet (45 m) cable distance from the
probe.
8. Optional explosion-proof HPS enclosure allows use in hazardous gas
areas.
e. Handling the Oxygen Analyzer
It is important that printed circuit
boards and integrated circuits are
handled only when adequate antistatic
precautions have been taken to
prevent possible equipment damage.
The oxygen analyzer is designed for
industrial application. Treat each
component of the system with care to
avoid physical damage. The probe
contains components made from
ceramics, which are susceptible to
shock when mishandled.
NOTE
Retain packaging in which the oxygen
analyzer arrived from the factory in
case any components are to be
shipped to another site. This packaging has been designed to protect the
product.
f.
A source of instrument air is required at the
probe for reference gas use. Since the
probe is equipped with an in place calibration feature, provision should be made for
connecting test gas tanks to the oxygen
analyzer when the probe is to be calibrated.
NOTE
Ambient air is not recommended for
use as high test gas. An 8% O2 balance in nitrogen is recommended for
high test gas.
If test gas bottles will be hooked up permanently, a check valve is required next to the
calibration fittings on the probe junction box.
This is to prevent breathing of calibration
gas line and subsequent flue gas condensation and corrosion. The check valve is in
addition to the stop valve in the test gas kit
or the solenoid valve in the multiprobe test
gas sequencer units.
GASES
DUCT
STACK
System Considerations
Prior to installation of your Rosemount
World Class 3000 Oxygen Analyzer with
Heater Power Supply Field Module, make
sure you have all of the components necessary to make the system installation. Ensure
all components are properly integrated to
make the system functional.
Once you have verified you have all the
components, select mounting locations and
determine how each component will be
placed in terms of available power supply,
ambient temperatures, environmental considerations, convenience, and serviceability.
Rosemount Analytical Inc.
A Division of Emerson Process Management
CALIBRATION
GAS
ADAPTER
PLATE
INSTRUMENT
AIR SUPPLY
(REF. GAS)
OXYGEN
ANALYZER
(PROBE)
PRESSURE
REGULATOR
FLOWMETER
HEATER POWER
SUPPLY
LINE
VOLTAGE
}
ELECTRONICS
PACKAGE
19260002
Figure 1-2. Typical System Installation
Description
1-3
1
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
EXISTING
ELECTRONICS
RELAY
ANALOG
HEATER
STACK
TEMP
+
+
PROBE
MV
PROBE
TC
}
}
}
}
*TRIAC
+
BK WH
YE
WH
AD590
}
}
}
RD
BK
GN
J9
+
OR
BL
+
+
SHIELD
RD
YE
OR
BK
WH
BL
J8
GN
}
}
SHIELD
YE
PROBE
TC
PROBE
MV
SHIELD
+
+
STACK
TC
}
+
GN
SHIELD
RD
YE
PROBE
HEATER
MAINS
}
BK
WH
R
N
H
J2
L
GN
BK
J1
WH
SHIELD
(SEE PARAGRAPH 2.2.b)
}
BL
SHIELD
OR
OR
BL
J3
RD
LINE VOLTAGE
BY CUSTOMER
HEATER POWER SUPPLY
HEATER
BK
GN
WH
RD
YE
OR
BL
1 2 3 4 5 6 7 8
PROBE HEAD
WIRING
STANDARD PROBE CABLE
6 M (20 FT)
24 M (80 FT)
12 M (40 FT)
30 M (100 FT)
18 M (60 FT)
45 M (150 FT)
BK
}
GN
BK
RD ALUMEL
OR CELL +VE
YE CHROMEL
BL CELL -VE
*GATE VOLTAGE CONTROLLING TRIAC OUTPUT
PROBE
TEST GAS INPUT
AT 2-3 L/MIN
(4-7 SCFH)
CHECK
VALVE
Figure 1-3. Typical System Wiring
1-4
Description
Rosemount Analytical Inc.
REF. GAS SUPPLY
INPUT AIR AT
1 L/MIN (2 SCFH)
19260003
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 2
INSTALLATION
2
2-1
OXYGEN ANALYZER (PROBE)
INSTALLATION
Before starting to install this equipment, read the "Safety instructions for
the wiring and installation of this apparatus" at the front of this Instruction
Bulletin. Failure to follow the safety
instructions could result in serious
injury or death.
Install all protective equipment covers
and safety ground leads after installation. Failure to install covers and
ground leads could result in serious
injury or death.
a. Selecting Location
1. The location of the probe in the stack
or flue is most important for maximum
accuracy in the oxygen analyzing process. The probe must be positioned so
that the gas it measures is representative of the process. Best results are
normally obtained if the probe is positioned near the center of the duct (40
to 60% insertion). A point too near the
edge or wall of the duct may not provide a representative sample because
of the possibility of gas stratification. In
addition, the sensing point should be
selected so that the process gas temperature falls within a range of 50° to
1300°F (10° to 704°C). Figure 2-1 provides mechanical installation
references.
2. Check the flue or stack for holes and
air leakage. The presence of this condition will substantially affect the accuracy of the oxygen reading. Therefore,
Rosemount Analytical Inc.
A Division of Emerson Process Management
either make necessary repairs or install
the probe upstream of any leakage.
3. Ensure that the area is clear of obstructions internal and external that will
interfere with installation. Allow adequate clearance for removal of probe
(Figure 2-1).
Do not allow the temperature of the
probe junction box to exceed 300°°F
(149°°C) or damage to the unit may result. If the probe junction box temperature exceeds 300°°F (149°°C), the user
must fabricate a heat shield or provide
adequate cooling air to the probe junction box.
b. Mechanical Installation
1. Ensure that all components are available for installation of the probe.
Ensure that the system cable is the required length. If applicable, check the
ceramic filter to ensure that it is not
damaged.
2. The probe may be installed intact as it
is received. It is recommended that you
disassemble the adapter plate for each
installation.
NOTE
An abrasive shield is recommended
for high velocity particulate in the flue
stream (such as those in pulverized
coal kilns and recovery boilers). Vertical and horizontal brace clamps are
provided for 9 ft and 12 ft (2.75 m and
3.66 m) probes to provide mechanical
support of the probe. Refer to Figure
2-1, Sheet 5.
3. Weld or bolt adapter plate (Figure 2-1)
onto the duct.
Installation
2-1
Installation
5.71
(145)
4.75
(121)
(4) HOLES
EQ SP ON BC
Rosemount Analytical Inc.
81.3 (2065)
117.3 (2980)
34 (864)
70 (1778)
106 (2692)
142 (3607)
3 FT
6 FT
9 FT
12 FT
DIM "B"
16 (406)
18 IN.
153.3 (3894)
45.3 (1151)
27.3 (694)
DIM "A"
PROBE
5.12
(130)
0.59
(15)
6.10
(155)
ANSI
DIN
JIS
CAL GAS
1/4 IN. TUBE
6 MM TUBE
6 MM TUBE
REF GAS
24610001
2. THESE FLAT FACED FLANGES ARE MANUFACTURED
TO ANSI, DIN, AND JIS BOLT PATTERNS AND ARE NOT
PRESSURE RATED.
NOTES: 1. DIMENSIONS ARE IN INCHES WITH MILLIMETERS IN
PARENTHESES.
BOTTOM VIEW
INSTALL WITH CONNECTIONS
AT THE BOTTOM
1.88 (48)
ELEC
CONN
1/2"
CONDUIT
DIM "B" REMOVAL ENVELOPE
7.58 (192)
5.85 (148.6)
ROSEMOUNT
INSULATE IF EXPOSED
TO AMBIENT
WEATHER CONDITIONS
106-300NE Rev. 3.4
May 2000
TABLE II INSTALLATION/REMOVAL
0.71
(18)
0.75
(20)
HOLE
DIA.
7.28
(185)
6.00
(153)
DIN
4512C19H01
FLANGE
DIA.
ANSI
4512C17H01
DIM "A"
WITH STANDARD
SNUBBER
DIFFUSER
JIS
4512C18H01
4.90 (124.5)
ADD TO DIM "A" FOR
PROBE WITH CERAMIC
DIFFUSER AND FLAME
ARRESTOR
TABLE I MOUNTING FLANGE
PROCESS FLOW MUST
BE IN THIS DIRECTION
WITH RESPECT TO
DEFLECTOR 3534848G01
3.80 (96.5)
ADD TO DIM "A"
FOR PROBE
WITH CERAMIC
DIFFUSER
2.27 (58)
DIA MAX
CAL
GAS
2-2
REF
GAS
FURNISHED IN - XIT
0.062 THK GASKET ADAPTER & ACCESSORY
ANSI 3535B18H02
4512C34
JIS
3635B48H01
4512C35
DIN 3535B45H01
4512C36
Instruction Bulletin
World Class 3000
Figure 2-1. Probe Installation (Sheet 1 of 5)
A Division of Emerson Process Management
Rosemount Analytical Inc.
103.1
(2619)
139.1
(3533)
81.3
(2065)
117.3
(2980)
153.3
(3894)
63
(1600)
99
(2515)
135
(3429)
6 FT
9 FT
12 FT
A Division of Emerson Process Management
3.6
NOMINAL
0.945
0.75
0.75
(8) HOLES
DIAMETER
7.48
7.48
7.50
BOLT
CIRCLE
INSULATE IF
EXPOSED TO
AMBIENT WEATHER
CONDITIONS
SEE TABLE IV
FOR FLANGE
SIZES
7.00
(178)
CHECK VALVE FOR
CAL GAS LINES
ELECTRICAL
CONNECTOR
DIM "D" REMOVAL ENVELOPE
14.5
(369)
5.7
(145)
* FLANGE ARE MANUFACTURED TO ANSI,
DIN, AND JIS BOLT PATTERNS AND ARE
FLAT FACED. THESE FLANGES ARE NOT
PRESSURE RATED.
9.25 (235)
9.25 (235)
JIS*
DIN*
9.00 (153)
ANSI*
FLANGE
DIAMETER
TABLE IV. FLANGE SIZE
21190008
REF AND
CAL GAS
CONNECTOR
World Class 3000
NOTE: DIMENSIONS ARE IN INCHES WITH
MILLIMETERS IN PARENTHESES.
SNUBBER DIFFUSION/
DUST SEAL ASSEMBLY
(P/N 4843B38G02)
0.06 THK GASKET FURNISHED
IN HARDWARE PACKAGE
(P/N 3535B58G02 - ANSI)
(P/N 3535B58G04 - JIS)
(P/N 3535B58G06 - DIN)
DIM "C"
DIM "E" (WITH FLAME ARRESTOR)
31.1
(790)
45.3
(1151)
27
(686)
3 FT
67.1
(1704)
DIM "E"
DIM "D"
DIM "C"
TABLE III. REMOVAL / INSTALLATION
NOMINAL MEASUREMENTS
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
2
Figure 2-1. Probe Installation (Sheet 2 of 5)
Installation
2-3
2-4
Installation
5.708
(145)
(M-16 x 2)
7.5
(191)
DIN
(P/N 4512C36G01)
B
C
45o
A
7.50
(191)
"D"
DIA
Rosemount Analytical Inc.
4 STUDS,
LOCKWASHERS AND
NUTS EQUALLY
SPACED ON
C DIA B.C.
ADAPTOR PLATE FOR 3, 6, 9,
AND 12 FT ABRASIVE SHIELD
INSTALLATIONS. SEE SHEET 2.
A
B
CROSSHATCHED AREA IN 4
CORNERS MAY BE USED TO
PROVIDE ADDITIONAL HOLES FOR
FIELD BOLTING OF PLATE TO
OUTSIDE WALL SURFACE.
A
C
22.5o
16860021
ABRASIVE SHIELD
FLANGE O.D.
8 THREADED HOLES
EQUALLY SPACED ON
D DIA B.C.
7.894
(200)
(M-20 x 2.5)
4.92
(125)
9.25
(235)
JIS
(P/N 3535B58G04)
NOTE: PART NUMBERS FOR ADAPTOR PLATES INCLUDE
ATTACHING HARDWARE.
7.48
(190)
(M-16 x 2)
0.625-11
"C"
THREAD
9.25
(235)
DIN
(P/N 3535B58G06)
3.94
(100)
9.00
(229)
ANSI
(P/N 3535B58G02)
4.75
(121)
"B"
DIA
"A"
DIMENSIONS
IN.
(mm)
TABLE VI. ADAPTOR PLATE DIMENSIONS FOR ABRASIVE SHIELD
106-300NE Rev. 3.4
May 2000
ADAPTOR PLATE FOR
STD WORLD CLASS 3000
PROBE INSTALLATION.
SEE SHEET 1.
2.500 DIA
A
5.118
(130)
(M-12 x 1.75)
6.50
(165)
JIS
(P/N 4512C35G01)
NOTE: PART NUMBERS FOR ADAPTOR PLATES INCLUDE
ATTACHING HARDWARE.
4.75
(121)
0.625-11
"B"
THREAD
"C"
DIA
6.00
(153)
ANSI
(P/N 4512C34G01)
"A"
DIMENSIONS
IN.
(mm)
TABLE V. ADAPTOR PLATE DIMENSIONS FOR PROBE
Instruction Bulletin
World Class 3000
Figure 2-1. Probe Installation (Sheet 3 of 5)
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
INSTALLATION FOR METAL
WALL STACK OR DUCT
CONSTRUCTION
INSTALLATION FOR MASONRY
WALL STACK CONSTRUCTION
2
0.50 (13)
0.50 (13)
BOLT ADAPTOR
PLATE TO OUTSIDE
WALL SURFACE
MTG HOLES
SHOWN oROTATED
22.5 OUT OF
TRUE POSITION
3.75 (95)
MIN DIA HOLE
IN WALL
STACK OR DUCT
METAL WALL
FIELD WELD
PIPE TO
ADAPTOR PLATE
MTG HOLES
SHOWN ROTATED
o
22.5 OUT OF
TRUE POSITION
PIPE 4.00 SCHED 40
PIPE SLEEVE (NOT
BY ROSEMOUNT)
LENGTH BY CUSTOMER
JOINT MUST
BE AIRTIGHT
WELD OR BOLT MOUNTING
PLATE TO METAL WALL
OF STACK OR DUCT.
JOINT MUST BE AIRTIGHT.
4.50 (114)
O.D. REF
MASONRY
STACK WALL
OUTSIDE WALL
SURFACE
NOTE:
ALL MASONRY STACK WORK AND JOINTS EXCEPT
ADAPTOR PLATE NOT FURNISHED BY ROSEMOUNT.
ABRASIVE SHIELD MOUNTING
BOLT MOUNTING
PLATE TO OUTSIDE
WALL SURFACE
FIELD WELD
PIPE TO
ADAPTOR PLATE
4.0 (102)
O.D. REF
3.25 (82.5)
MIN DIA HOLE
IN WALL
PIPE 3.5 SCHED 40
PIPE SLEEVE (NOT
BY ROSEMOUNT)
LENGTH BY CUSTOMER
STACK OR DUCT
METAL WALL
JOINT MUST
BE AIRTIGHT
MASONRY
STACK WALL
OUTSIDE WALL
SURFACE
WELD OR BOLT MOUNTING
PLATE TO METAL WALL
OF STACK OR DUCT.
JOINT MUST BE AIRTIGHT.
NOTE:
PROBE MOUNTING
DIMENSIONS IN INCHES WITH
MILLIMETERS IN PARENTHESES.
P0038
Figure 2-1. Probe Installation (Sheet 4 of 5)
Rosemount Analytical Inc.
A Division of Emerson Process Management
Installation
2-5
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
BRACE BARS
(NOT BY ROSEMOUNT)
NOTE: DIMENSIONS IN INCHES WITH
MILLIMETERS IN PARETHESES.
2.00
(51)
o
60 MAX.
}
1.00
(25)
30o MIN.
VERTICAL BRACE CLAMP ASSY.
BY ROSEMOUNT
HORIZONTAL BRACE CLAMP ASSY.
(BOTH BRACE CLAMP ASSEMBLIES ARE THE SAME.
INSTALLATION AND LOCATION OF CLAMP ASSEMBLIES
AND BRACE BARS TO BE DONE IN FIELD.)
2 HOLES - 0.625
(16) DIA. FOR
0.50 (12) DIA.
BOLT
5.62
(143)
ABRASIVE SHIELD
4.12
(105)
4.12
(105)
0.375
(10)
1.00
(25) MAX.
5.62
(143)
36.00 (914)
NOTE: BRACING IS FOR VERTICAL AND HORIZONTAL PROBE INSTALLATION.
EXTERNAL BRACING REQUIRED FOR 9 FT AND 12 FT
(2.75 M AND 3.66 M) PROBES AS SHOWN ABOVE.
P0039
Figure 2-1. Probe Installation (Sheet 5 of 5)
4. If using the optional ceramic diffusor
element, the vee deflector must be correctly oriented. Before inserting the
probe, check the direction of gas flow
in the duct. Orient the vee deflector on
the probe so that the apex points upstream toward the flow (Figure 2-2).
This may be done by loosening the
setscrews, and rotating the vee deflector to the desired position.
Retighten the setscrews.
5. In horizontal installations, the probe
junction box should be oriented so the
system cable drops vertically from the
probe junction box. In a vertical installation, the system cable can be oriented in any direction.
2-6
Installation
6. If the system has an abrasive shield,
check the diffusion element dust seal
packings. The joints in the two packings must be staggered 180°. Also,
make sure that the packings are in the
hub grooves as the probe slides into
the 15° forcing cone in the abrasive
shield.
7. Insert the probe through the opening in
the mounting flange and bolt the unit to
the flange. When probe lengths selected are 9 or 12 feet (2.74 or 3.66 m),
special brackets are supplied to provide additional support for the probe
inside the flue or stack. See Figure 2-1,
sheet 5.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
c. Service Required
GAS FLOW
DIRECTION
APEX
VEE
DEFLECTOR
FILTER
1. Power input: 100, 115 or 220 Vac single phase, 50 to 60 Hz, 3 amp
minimum. (See label.)
DIFFUSION
ELEMENT
SETSCREW
VEE
DEFLECTOR
2. Compressed air: 10 psig (68.95 kPag)
minimum, 225 psig (1551.38 kPag)
maximum at 2 scfh (56.6 L/hr) maximum; supplied by one of the following
(less than 40 parts-per-million total hydrocarbons). Regulator outlet pressure
should be set at 5 psi (35 kPa).
(a) Instrument air - clean, dry.
(b) Bottled standard air with step-down
regulator.
P0017
Figure 2-2. Orienting the Optional Vee Deflector
(c) Bottled compressed gas mixture
(20.95% oxygen in nitrogen).
(d) Other equivalent clean, dry, oil-free
air supply.
Figure 2-3. Outline of Heater Power Supply
Rosemount Analytical Inc.
A Division of Emerson Process Management
Installation
2-7
2
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
EXISTING
ELECTRONICS
RELAY
ANALOG
HEATER
STACK
TEMP
+
+
PROBE
MV
PROBE
TC
}
}
}
}
*TRIAC
+
BK WH
YE
WH
AD590
}
}
}
RD
BK
GN
J9
+
OR
BL
+
+
SHIELD
RD
YE
OR
BK
WH
BL
J8
GN
}
}
SHIELD
YE
PROBE
TC
PROBE
MV
SHIELD
+
+
STACK
TC
}
+
GN
SHIELD
RD
YE
PROBE
HEATER
MAINS
}
BK
WH
R
N
H
J2
L
GN
BK
J1
WH
SHIELD
(SEE PARAGRAPH 2.2.b)
}
BL
SHIELD
OR
OR
BL
J3
RD
LINE VOLTAGE
BY CUSTOMER
HEATER POWER SUPPLY
HEATER
BK
WH
GN
RD
YE
OR
BL
1 2 3 4 5 6 7 8
PROBE HEAD
WIRING
STANDARD PROBE CABLE
6 M (20 FT)
24 M (80 FT)
12 M (40 FT)
30 M (100 FT)
18 M (60 FT)
45 M (150 FT)
BK
}
GN
BK
RD ALUMEL
OR CELL +VE
YE CHROMEL
BL CELL -VE
*GATE VOLTAGE CONTROLLING TRIAC OUTPUT
PROBE
TEST GAS INPUT
AT 2-3 L/MIN
(4-7 SCFH)
CHECK
VALVE
Figure 2-4. Electrical Installation of Heater Power Supply
2-8
Installation
Rosemount Analytical Inc.
REF. GAS SUPPLY
INPUT AIR AT
1 L/MIN (2 SCFH)
19260003
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
2
Figure 2-5. Heater Power Supply Wiring Connections
2-2
HEATER POWER SUPPLY INSTALLATION
Install all protective equipment covers
and safety ground leads after installation. Failure to install covers and
ground leads could result in serious
injury or death.
a. Mechanical Installation
The outline drawing of the heater power
supply enclosure, Figure 2-3, shows
mounting centers and clearances. The
NEMA 4X enclosure is designed to be
mounted on a wall or bulkhead. The heater
power supply should be installed no further
than 150 feet (45 m) from the probe. The
heater power supply must be located in a
location free from significant ambient tem-
Rosemount Analytical Inc.
A Division of Emerson Process Management
perature changes and electrical noise.
Ambient temperature must be between -20°
to 140°F (-30° to 60°C).
b. Electrical Connections
1. Electrical connections should be made
as described in the electrical installation diagram, Figure 2-4. The wiring
terminals are divided into two layers;
the bottom (FROM PROBE) terminals
should be connected first, the top
(FROM ELECTRONICS) terminals
should be connected (Figure 2-5).
Each terminal strip has a protective
cover which must be removed when
making connections. To remove the
terminal covers, remove two slotted
screws holding the cover in place. Always reinstall terminal covers after
making connections.
Installation
2-9
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
JUMPER
CONFIGURATIONS
1
LINE VOLTAGE
SELECTION
JUMPER
(INSTALL)
100/120 V.A.C.
ALWAYS DISCONNECT LINE VOLTAGE
FROM HEATER POWER SUPPLY AND
ANALOG ELECTRONICS (IF USED)
BEFORE CHANGING JUMPERS.
HEATER
POWER
JUMPER
JM4, JM1
REMOTE
REMOVE JM2
220/240 V.A.C.
JM5
*ON
INSTALL JM2
PROBE HEATER
VOLTAGE SELECTION
JUMPER
(INSTALL)
ELECTRONICS
SELECTION
*WORLD CLASS PROBE
(44V)
JM7
*ANALOG (EXISTING)
INSTALL JM3, JM6
218 PROBE (115V)
JM8
DIGITAL
(NEXT GENERATION)
REMOVE JM3, JM6
2
JUMPER
* DENOTES JUMPERS THAT MUST BE INSTALLED WHEN USING THE WORLD CLASS 3000 OXYGEN ANALYZER
PROBE AND THE HPS 3000 HEATER POWER SUPPLY WITH EXISTING ANALOG, MODEL 218A, AND TC 2000
ELECTRONICS.
NOTES:
1
100 V.A.C. OPERATION REQUIRES TRANSFORMER PART NUMBER 1M02961G02.
2
HEATER POWER IS ALSO REFERRED TO AS LINE VOLTAGE RELAY.
Figure 2-6. Jumper Selection Label
NOTE
Refer to Figure 2-7 for HPS unit fuse
locations and specifications.
3. The power cable should comply with all
applicable codes and safety regulations in the user's country and should
not be smaller than 16 gauge, 3 amp.
NOTE
Before supplying power to the heater
power supply, verify that jumpers JM2,
JM3, JM6, and JM7 are installed.
2. Power Input: 120, 220 or 240 Vac. For
120 Vac usage, install jumpers JM4
and JM1. For 220 or 240 Vac usage,
install jumper JM5 (See label, Figure
2-6).
For 100 Vac usage, the heater power
supply is factory-supplied with a different transformer. When using the HPS
with 100 Vac transformer, install
jumpers JM1 and JM4.
2-10
Installation
NOTE
"ANALOG" under ELECTRONICS SELECTION on the label refers to Models
218, 225, TC200, and Model 218A electronics.
4. Before supplying power to the heater
power supply, verify that the jumpers
on the mother board, Figure 2-7, are
properly configured. Jumpers JM2,
JM3, JM6, and JM7 should be installed. Additionally, make sure that the
proper jumper for your line voltage is
installed, Figure 2-6.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
2
JM1
FUSES
JM2
JM4
JM3
JM6
JM7
JM5
JM8
3D3 080G REV
FUSE
NOTE: ALL FUSES ARE 5A @ 250 VAC,
ANTI-SURGE, CASE SIZE
5 X 20 MM, TYPE T TO IEC127,
SCHURTER.
22540005
Figure 2-7. Jumpers on HPS Mother Board
!
NOTE
Upon completing installation, make sure that the probe is turned on and operating
prior to firing up the combustion process. Damage can result from having a cold
probe exposed to the process gases.
During outages, and if possible, leave all probes running to prevent condensation and
premature aging from thermal cycling.
If the ducts will be washed down during outage, MAKE SURE to power down the
probes and remove them from the wash area.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Installation
2-11
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
2-12
Installation
World Class 3000
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 3
SETUP
3-1
OVERVIEW
a. Open electronics enclosure.
This section covers the setup procedures for the
World Class 3000 Oxygen Analyzer with HPS
3000 Heater Power Supply Field Module. Since
this equipment may be used with a number of
different electronics packages, this section has
been divided into three parts: Models 218, 225,
and 132 (Analog) Electronics, Model 218A,
Electronics, and Model TC200 Electronics. Each
of the three parts contain setup information applicable to that electronics package.
b. On temperature controller card, Figure 3-1,
connect jumper wire from TP3 to either Pin
2 or Pin 7.
c. Set voltmeter to read DC millivolts (MV).
d. Attach voltmeter with positive (+) lead on
TP1 and negative (-) on either Pin 2 or 7.
e. Adjust potentiometer M110-1 to read -322.3
millivolts nominal.
Install all protective equipment covers
and safety ground leads after setup.
Failure to replace covers and ground
leads could result in serious injury or
death.
Models 218, 225, and 132 (Analog)
Electronics refer to paragraph 3-2.
Model 218A Electronics
refer to paragraph 3-3.
MODEL TC200 Electronics
refer to paragraph 3-4.
Model 132 Digital Electronics
refer to paragraph 3-5.
3-2
MODELS 218, 225, AND 132 (ANALOG)
ELECTRONICS SETUP
Before beginning operation, it is important that
the probe heater set point of the existing electronics be changed to support the World Class
3000 probe. The set point adjustment procedure
required for Models 218, 225, and 132 analog
electronics is as follows:
Rosemount Analytical Inc.
A Division of Emerson Process Management
Figure 3-1. Temperature Controller Card
Calibration Points
Setup
3-1
3
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
NOTE
The voltage given above is for an ambient (machinery space) temperature
of 77°F (25°C). For each degree of ambient temperature above or below 77°F
(25°C), add or subtract 0.242 mV from
the nominal. Example; at 87°F (31°C),
the nominal voltage of -322.3 should
be increased (made less negative) by
10 x 0.242 or 2.42 mV, making the adjusted nominal -319.9.
f.
3-3
Remove voltmeter leads.
G02
United States
United Kingdom
Germany
France
Italy
1M03192G01
1M03192G02
1M03192G03
1M03192G04
1M03192G05
G04
1M02982G01
1M02982G02
1M02982G03
1M02982G04
1M02982G05
NOTE
The replacement EPROM when using a
multiprobe averager unit is
1M02982G10.
g. Remove jumper wire.
To replace the EPROM, proceed as follows:
MODEL 218A ELECTRONICS SETUP
a. Shut off and lock out power to the electronics package.
Before beginning operation, it is important that
the probe heater set point of the existing electronics be changed to support the World Class
3000 probe. To convert the Model 218A Digital
Electronics Package for use with the World
Class 3000 Probe and Heater Power Supply,
an EPROM change is necessary. Remove Main
PCB and check back of board to identify unit as
G02 or G04. The replacement EPROM needed
is as identified below:
b. Open electronics enclosure.
c. On the Main PCB, Figure 3-2, locate and
remove old EPROM.
d. Replace with new EPROM.
e. Close electronics enclosure and power up
system.
Figure 3-2. Main PCB (Model 218A) EPROM Replacement
3-2
Setup
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
3
Figure 3-3. Main PCB (Model TC200) EPROM Replacement
3-4
MODEL TC200 VERITRIM ELECTRONICS
SETUP
Before beginning operation, it is important that
the probe heater set point of the existing electronics be changed to support the World Class
3000 Probe. To convert the Model TC200 Electronics Package for use with the World Class
3000 Probe and Heater Power Supply, an
EPROM change is necessary. The replacement
EPROM needed is part number 1M03154G02.
a. EPROM Replacement
To replace the EPROM, proceed as follows:
1. Shut off and lock out power to the
electronics package.
4. Replace with new EPROMs (part number 1M03154G02) being careful to install U11 and U12 in their proper
locations.
5. Close electronics enclosure and power
up system.
b. Heater Set Point Adjustment
The adjustment procedure required for the
Model TC200 Electronics Package is as
follows:
1. Open keylocked enclosure to access
membrane keyboard.
2. Open electronics enclosure.
2. Put controller in PAR (parameter)
mode by depressing "LOCK" "▲"
"%O2" "INC" "ACK" in sequence.
3. On the main PCB, Figure 3-3, locate
and remove old EPROMs U11 and
U12.
3. Depress "ACK" pushbutton to clear
display.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Setup
3-3
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
4. Press "NUM" pushbutton.
5. Using "INC", "DEC" buttons, display
parameter 125.
6. Press "VAL" button.
7. Using "INC", "DEC" buttons, change
parameter 125 value to 15.4.
8. Press "ENT" to save new value.
3-5
MODEL 132 DIGITAL ELECTRONICS
SETUP
Before beginning operation, it is important that
the probe heater set point of the existing electronics be changed to support the World Class
3000 Probe. To convert the Model 132 Digital
Electronics Package for use with the World
Class 3000 Probe and Heater Power Supply, an
EPROM change is necessary. The replacement
EPROM needed is as identified below:
United States
United Kingdom
Germany
France
Italy
IM03222G01
To replace the EPROM, proceed as follows:
a. Shut off and lock out power to the
electronics package.
b. Open electronics enclosure.
c. On the Main PCB, Figure 3-4, locate and
remove old EPROM.
d. Replace with new EPROM.
e. Close electronics enclosure and power up
system.
Figure 3-4. Main PCB (Model 132) EPROM Replacement
3-4
Setup
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 4
TROUBLESHOOTING
4-1
b. HPS 3000 Heater Power Supply
OVERVIEW
Troubleshooting information for the HPS
3000 Heater Power Supply is contained in
Appendix B, HPS 3000 Troubleshooting.
Troubleshooting for the oxygen analyzer system
is broken down to the main component level.
Faults within the probe or heater power supply
may cause symptoms which overlap.
c. Model 218 and 225 (Analog)
Electronics Package
Install all protective equipment covers
and safety ground leads after troubleshooting. Failure to replace covers
and ground leads could result in serious injury or death.
4-2
Troubleshooting information for the Model
218 and 225 Electronics Package is contained in IB-106-101.
d. Model 218A Electronics Package
Troubleshooting information for the Model
218 Electronics Package is contained in IB106-101A.
SYSTEM TROUBLESHOOTING
Troubleshooting of individual components within
the oxygen analyzer system are contained in
the following.
e. TC200 Veritrim Electronics Package
Troubleshooting information for the TC200
VeriTrim Electronics Package is contained
in IB-107-020.
a. World Class 3000 Probe
Troubleshooting information for the World
Class 3000 Probe is contained in Appendix
A, Probe Troubleshooting.
Rosemount Analytical Inc.
A Division of Emerson Process Management
f.
Model 132 Digital Electronics Package
Troubleshooting information for the Model
132 Electronics Package is contained in IB
106-106A.
Troubleshooting
4-1
4
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
4-2
Troubleshooting
World Class 3000
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 5
RETURN OF MATERIAL
5-1
If factory repair of defective equipment is
required, proceed as follows:
5. Complete shipping instructions for
return of equipment.
a. Secure a return authorization number from
a Rosemount Analytical Sales Office or
Representative before returning the equipment. Equipment must be returned with
complete identification in accordance with
Rosemount instructions or it will not be
accepted.
6. Reference the return authorization
number.
In no event will Rosemount be responsible
for equipment returned without proper
authorization and identification.
b. Carefully pack defective unit in a sturdy box
with sufficient shock absorbing material to
insure that no additional damage will occur
during shipping.
c. In a cover letter, describe completely:
1. The symptoms from which it was determined that the equipment is faulty.
2. The environment in which the equipment has been operating (housing,
weather, vibration, dust, etc.).
3. Site from which equipment was
removed.
d. Enclose a cover letter and purchase order
and ship the defective equipment according
to instructions provided in Rosemount
Return Authorization, prepaid, to:
Rosemount Analytical Inc.
RMR Department
1201 N. Main Street
Orrville, Ohio 44667
If warranty service is requested, the defective unit will be carefully inspected and
tested at the factory. If failure was due to
conditions listed in the standard Rosemount
warranty, the defective unit will be repaired
or replaced at Rosemount's option, and an
operating unit will be returned to the customer in accordance with shipping
instructions furnished in the cover letter.
For equipment no longer under warranty,
the equipment will be repaired at the factory
and returned as directed by the purchase
order and shipping instructions.
4. Whether warranty or nonwarranty
service is requested.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Return of Material
5-1
5
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
5-2
Return of Material
World Class 3000
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 6
APPENDICES
APPENDIX A. WORLD CLASS 3000 OXYGEN ANALYZER (PROBE)
APPENDIX B. HPS HEATER POWER SUPPLY FIELD MODULE
6
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
6-1
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
APPENDIX A
NOTE: NOT ALL PARTS SHOWN ARE AVAILABLE FOR
PURCHASE SEPARATELY. FOR LIST OF
AVAILABLE PARTS, SEE TABLE A-3.
1
26
20
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Heater, Strut, and Backplate Assembly
Diffusion Assembly
Retainer Screw
Cell and Flange
Corrugated Seal
Probe Tube Assembly
Screw
Washer
Cover Chain Screw
Cover Chain
Probe Junction Box Cover
Cover Gasket
Wiring Diagram
O-Ring
Terminal Block Screws
Terminal Block
Terminal Block Marker
Terminal Block Mounting Plate
21
28
29
3
20
27
17
19
25
24
15
13 11
11
2
10
4
18
22
23
5
8
16
7
14
12
10
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
Probe Junction Box Screws
Hose Clamp
Hose
Gas Connection
Seal Cap
Label
Probe Junction Box
Ground Wires
Insulating Gasket
Washer
Screw
6
9
NOTE: ITEM
, CALIBRATION GAS TUBE,
FITS INTO HOLES
ASSEMBLED.
WHEN PROBE IS
21240005
Figure A-1. Oxygen Analyzer (Probe) Exploded View
A-0
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
APPENDIX A, REV. 3.6
WORLD CLASS 3000 OXYGEN ANALYZER (PROBE)
DESCRIPTION
A-1
Read the “Safety instructions for the
wiring and installation of this apparatus” at the front of this Instruction
Bulletin. Failure to follow the safety
instructions could result in serious
injury or death.
OXYGEN ANALYZER (PROBE) - GENERAL
The Oxygen Analyzer (Probe), Figure A-1, consists of three component groups: probe exterior,
inner probe, and probe junction box, Figure A-2.
PROBE
EXTERIOR
(SENSING CELL INSTALLED)
PROBE
INTERIOR
PROBE
JUNCTION
BOX
21240006
Figure A-2. Main Probe Components
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
A-1
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
1, 2
Table A-1. Specifications for Oxygen Analyzing Equipment.
Probe lengths, nominal ................................................................. 18 inches (457 mm), 3 feet (0.91 m), 6 feet
(1.83 m), 9 feet (2.74 m), or 12 feet (3.66 m),
depending on duct dimensions
Temperature limits in process
measurement area............................................................ 50° to 1300°F (10° to 704°C)
Standard/current output ................................................................. 4-20 mA dc signal (factory set)
O2 indication (Digital display
and analog output) ............................................................ 0.1% O2 or ±3% of reading, whichever is
greater using Rosemount calibration gases
System speed of response ............................................................ less than 3 seconds (amplifier output)
Resolution sensitivity...................................................................... 0.01% O2 transmitted signal
HPS 3000 housing ......................................................................... NEMA 4X (IP56)
Probe reference air flow................................................................. 2 scfh (56.6 L/hr) clean, dry, instrument quality
air (20.95% O2), regulated to 5 psi (34 kPa)
Calibration gas mixtures ................................................................ Rosemount Hagan Calibration Gas Kit Part No.
6296A27G01 contains 0.4% O2N2 Nominal and
8% O2N2 Nominal
Calibration gas flow........................................................................ 5 scfh (141.6 L/hr)
HPS 3000 Power supply .............................................................. 100/110/220 ±10% Vac at 50/60 Hz
HPS 3000 Power requirement ..................................................... 200 VA
HPS 3000 Ambient Operating Temperature................................ 32° to 120°F (0° to 50°C)
Ambient operating temperature (Probe Junction Box) .................. 300°F (150°C) max
Approximate shipping weights:
18 inch (457 mm) package ............................................... 55 pounds (24.97 kg)
3 foot (0.91 m) package .................................................... 60 pounds (27.24 kg)
6 foot (1.83 m) package .................................................... 65 pounds (29.51 kg)
9 foot (2.74 m) package .................................................... 72 pounds (32.66 kg)
12 foot (3.66 m) package .................................................. 78 pounds (35.38 kg)
1
2
All static performance characteristics are with operating variables constant.
Equipment ordered utilizing this document as reference will be supplied to the USA standard design. Customers requiring the EEC standard design should request the EEC documentation and utilize its ordering data.
Temperatures over 1000°F (537°C) may affect the ease of field cell replaceability.
A-2
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
A-2
c. Snubber Diffusion Assembly
PROBE ASSEMBLY EXTERIOR
Primary probe exterior components include a
flange-mounted zirconium oxide cell, mounted
on a tube assembly and protected by a snubber
diffusion assembly.
The snubber diffusion assembly protects
the cell from heavy particles and isolates
the cell from changes in temperature. The
snubber diffusion assembly threads onto
the cell and flange assembly. Pin spanner
wrenches (probe disassembly kit
3535B42G01) are applied to holes in the
snubber diffusion element hub to remove or
install the snubber diffusion assembly.
a. Cell and Flange Assembly
The primary component in the cell and
flange assembly, Figure A-3, is a
yttria-stabilized zirconium oxide cell. It creates an electrical signal when the oxygen
level on one side is out of balance with the
oxygen level on the other side. This signal
is proportional to the difference in oxygen
levels.
An optional ceramic diffusor element and
vee deflector, shown in Figure A-4, is
available. The ceramic diffusor assembly is
also available in a flame arresting version to
keep heat from the cell from igniting flue
gases.
b. Probe Tube Assembly
Four screws secure the cell and flange assembly, Figure A-3, to the probe tube assembly. When in place, the cell is inside the
tube.
Systems that use an abrasive shield require
a special snubber diffusion assembly with a
hub that is grooved to accept two dust seal
gaskets. This special diffusor is available in
both snubber and ceramic versions. See
Probe Options, section A-6.
The tube assembly includes a flange which
mates with a stack-mounted flange (shown
attached to the probe flange in Figure A-2).
Studs on the stack flange make installation
easy. There is also a tube to carry
calibration gas from the probe junction box
to the process side of the cell during
calibration.
DIFFUSION
ELEMENT
PROBE TUBE
CORRUGATED
SEAL
CELL AND
FLANGE
ASSEMBLY
HUB
PIN
WRENCH
VEE
DEFLECTOR
21240024
21240007
Figure A-3. Cell and Tube Assemblies
Rosemount Analytical Inc.
A Division of Emerson Process Management
Figure A-4. Optional Ceramic Diffusor and Vee
Deflector Assembly
Appendices
A-3
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
d. Cell - General
The components which make up the cell are
machined to close tolerances and
assembled with care to provide accurate
oxygen measurements. Any replacement
requires attention to detail and care in
assembly to provide good results.
Failure to follow the instructions in
this manual could cause danger to
personnel and equipment. Read and
follow instructions in this manual
carefully.
The oxygen probe includes an inner
electrode for the cell assembly. It consists of
a platinum pad and a platinum/inconel
composite wire which produces the cell
constant offset voltage described in the
Nernst equation.
World Class 3000
b. A heater that is helically wrapped on a
quartz support cylinder and insulated.
c. A chromel-alumel thermocouple which acts
as the sensing element for the temperature
controller. (Not visible in Figure A-5; located
within ceramic support rod.)
d. A platinum screen pad which forms
electrical contact with the inner electrode of
the electrochemical cell. (Not visible in
Figure A-5; located at end of ceramic
support rod.) The pad is attached to an
inconel wire which carries the signal to the
terminal strip.
e. A V-strut assembly to give support to the
inner probe assembly.
f.
A tube to carry reference air to the cell.
Turn to Service and Normal Maintenance, for
repair procedures for probe components.
With this pad and wire, the constant will be
between -10 and +15 mV. The cell constant
is noted in the calibration data sheet
supplied with each probe.
Every probe should be calibrated and
checked after repair or replacement of cell,
pad and wire, heater, and thermocouple, or
after disassembly of the probe.
A-3
INNER PROBE ASSEMBLY
HEATER
INSULATING
GASKET REFERENCE
AIR TUBE
V-STRUT
CERAMIC
SUPPORT
ROD
The inner probe assembly, Figure A-5, consists
of six main parts:
a. Ceramic support rod with four holes running
through the length. The holes serve as
insulated paths for the cell signal wire and
thermocouple wires.
A-4
Appendices
27270015
Figure A-5. Inner Probe Assembly
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
PROBE
JUNCTION BOX
COVER
TERMINAL
STRIP
During calibration, two gases of different known
oxygen concentrations are injected one at a
time through the calibration gas fitting. Stainless
steel tubing delivers this gas to the process side
of the cell. In a healthy cell, the difference in
oxygen pressure from the process side to the
reference side of the cell will cause a millivolt
output proportional to the difference in oxygen
levels. The electronics unit can use the two
millivolt outputs caused by the two calibration
gases for either automatic or semi-automatic
calibration.
Do not attempt to remove a process
gas sample through either gas fitting.
Hot gases from the process would
damage gas hoses in the probe
junction box.
CALIBRATION
GAS FITTING
A-5
REFERENCE
AIR FITTING
The system uses a 7-conductor cable to
connect the probe to the electronics package.
Standard length for this cable is 20 feet (6 m),
but lengths up to 150 feet (45 m) are available.
The seven conductors include one shielded pair
of wires for the cell millivolt signal, one shielded
pair of type K wires for the thermocouple, and
three individual 16-gauge wires for the heater
and for ground. The assembled conductors are
TM
wrapped by a type K Teflon jacket and
TM
braided stainless steel shield. The Teflon and
stainless steel jacketing is suitable for high
temperature use. All metal shields are isolated
at the probe end and connect by drain wires to
ground at the electronics.
27270016
Figure A-6. Probe Junction Box
A-4
PROBE JUNCTION BOX
The probe junction box, Figure A-6, is
positioned at the external end of the probe and
contains a terminal strip for electrical
connections and fittings for reference air and
calibration gases. Fittings are for 0.250 inch
stainless steel tubing on American units and
6 mm on European units. The calibration fitting
has a seal cap which must remain in place
except during calibration. A tubing fitting is also
supplied to be used with the calibration gas
supply during calibration.
If the calibration gas bottles will be permanently
hooked up to the probe, a manual block valve is
required at the probe (between the calibration
fitting and the gas line) to prevent condensation
of flue gas down the calibration gas line.
During operation and calibration, reference air is
supplied through the reference air fitting to the
reference side of the cell. This gives the system
a known quantity of oxygen with which to
compare the oxygen level in the process gas.
Though ambient air can be used for this
purpose, accuracy can only be assured if a
reference air set is used.
Rosemount Analytical Inc.
A Division of Emerson Process Management
CABLE ASSEMBLY
A-6
PROBE OPTIONS
a. Abrasive Shield Assembly
The abrasive shield assembly, Figure A-7,
is a stainless-steel tube that surrounds the
probe assembly. The shield protects the
probe against particle abrasion and
corrosive condensations, provides a guide
for ease of insertion, and acts as a probe
position support, especially for longer length
probes. The abrasive shield assembly uses
a modified diffusor and vee deflector
assembly, fitted with dual dust seal packing.
Appendices
A-5
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
2
.187 1
.187
B
A
15
o
3.584
3.554
90o
ON INSIDE BREAK
FOR SMOOTH
ROUNDED EDGE ON
BOTH ENDS
OF CHAMFER
A
.45 MIN
.187
B
125
6.00
SKIN CUT FACE FOR 90
o
VIEW A
VIEW B
22.5
o
0.75 THRU 4 PLS,
EQ SP ON 4.75 B.C.
NOTES:
1 WELD ON BOTH SIDES WITH EXPANDING
CHILL BLOCK.
2 BEFORE WELDING, BUTT ITEM 2 OR 4 WITH
ITEM 1 AS SHOWN.
.745 DIA ON A 7.50 DIA B.C. (REF)
.755
16860033
Figure A-7. Abrasive Shield Assembly
NOTE
In highly abrasive applications, rotate the shield 90 degrees at normal
service intervals to present a new wear surface to the abrasive flow stream.
A-6
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
19280010
P0010
Figure A-8. Ceramic Diffusion/Dust Seal Assembly
These modified diffusion and vee deflector
assemblies are available in standard, Figure
A-8, and flame arrestor version, Figure A-9.
b. Ceramic Diffusion Assembly
The ceramic diffusion assembly, Figure
A-10, is the traditional design for the probe.
Used for over 25 years, the ceramic diffusion assembly provides a greater filter surface area for the probe.
P0011
Figure A-9. Flame Arrestor Diffusion/Dust
Seal Assembly
Rosemount Analytical Inc.
A Division of Emerson Process Management
Figure A-10. Ceramic Diffusion Assembly
c. Flame Arrestor Diffusion Assembly
Where a high concentration of unburned
fuel is present in the exhaust gases, a flame
arrestor diffusion assembly, Figure A-9 and
Figure A-11 is recommended.
The flame diffusion assembly includes a set
of baffles between the cell and the stack
gases. This keeps 1500°F (816°C) cell temperatures from igniting unburned fuel in the
stack.
P0012
Figure A-11. Flame Arrestor Diffusion Assembly
Appendices
A-7
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
an 18 inch (457 mm) or 3 foot (0.92 m)
probe mounted externally on the stack or
duct. The process or exhaust gases are directed out to the probe through a passive
sampling system using inconel tubes. Flue
gas flow induces the movement of gases
into, through, and out of the bypass unit.
The bypass arrangement does not require
the use of aspiration air and the gas which
flows past the probe is returned to the stack
or duct.
The bypass probe package is normally used
for process temperatures of 1300°F (704°C)
to 2000°F (1094°C). A higher temperature
version of the bypass provides for operation
at temperatures up to 2500°F (1372°C). In
this version the pick up tubes are made of a
special high-temperature alloy.
Figure A-12. Snubber Diffusion/Dust
Seal Assembly
d. Snubber Diffusion/Dust Seal Assembly
The snubber diffusion/dust seal assembly,
Figure A-12, is used in applications where
an abrasive shield is to be used with a
snubber type diffusion element. The dust
seal consists of two rings of packing to prevent abrasive dust from collecting inside the
abrasive shield.
e. Bypass Probe Options
For processes where the flue gas exceeds
the maximum allowable temperature of
1300°F (704°C) a bypass sensor package
can be employed. The bypass system uses
A-8
Appendices
Overall dimensions and mounting details of
the American and European bypass systems are shown in Figure A-13.
f.
Probe Mounting Jacket Options
A probe mounting jacket option is available
to allow the probe to operate at temperatures of up to 2000°F (1095°C). A separate
instruction bulletin is available for this
option.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Rosemount Analytical Inc.
A Division of Emerson Process Management
4
DRAIN
05
OPTIONAL MOUNTING
ARRANGEMENT, 4 IN.
150# FLANGE SUPPLIED
BY CUSTOMER
06 GASKET AND HARDWARE
6.50
(165.1) REF
6.0
(152.4) REF
02 03 04
VIEW
2 CAL
GAS
1 REF
AIR
ELECT CABLE
109.00 (2768.6) REF (4507C26G03)
37.00 (939.8) REF (4507C26G01)
73.00 (1854.2) REF (4507C26G02)
30.62 (777.75) REF (4507C26G01)
27270017
DIRECTION
OF FLOW
A-A
C 9 FT (2743.2) GAS TUBE PICK-UP
62.50 (1587.5) REF (4507C26G03)
26.50 (673.1) REF (4507C26G01 AND G02)
4.026
(102.26)
I.D.
GAS TUBE PICK-UP
B 6 FT (1828.8) GAS TUBE PICK-UP
A 3 FT (914.4)
GROUP NOTE
7. DIMENSIONS ARE IN INCHES WITH MILLIMETERS IN PARENTHESES.
FLANGE
01
4. INSTALL WITH ANALYZER IN A VERTICALLY DOWNWARDS DIRECTION ONLY.
5. FLUE GAS OPERATING TEMPERATURE RANGE 1200o TO 1800oF (650o TO 980oC).
6. RECOMMENDED TWO INCH THK INSULATION. THERMAL CONDUCTIVITY K
EQUALS 0.5 FOR INSULATION.
3. LAG TO ENSURE GAS TEMPERATURE DOES NOT GO BELOW DEW POINT OR
EXCEED 500oC.
GASKET AND
06 HARDWARE
A
2. CALIBRATION AND PURGE GAS CONNECTION. BITE TYPE FITTING (PARKER CPI)
10 SCFH AT 32 PSIG MAX. CALIBRATION GAS REQUIRED.
NOTES: 1. REFERENCE AIR SUPPLY CONNECTION BITE TYPE FITTING (PARKER CPI) FOR
0.250 O.D. TUBING. 2 SCFH AT 3 PSIG MAX. CLEAN DRY AIR REQUIRED. FITTING
IS LOCATED ON FAR SIDE.
World Class 3000
IF EQUIPPED WITH THE OPTIONAL
CERAMIC DIFFUSOR ASSEMBLY, PROBE
ASSEMBLY MUST BE ORIENTED SO THAT
VEE SHIELD IS SQUARE TO GAS FLOW.
19.80 (502.92)
FOR
3D3947G01
6
3
27.31 (693.67)
CLEARANCE REQ
FOR PROBE
INSERTION
AND REMOVAL
A
STD 20 FT
(6.1 M) CABLE
Instruction Manual
Appendix A Rev. 3.6
July 1998
Figure A-13. Bypass Probe Option (Sheet 1 of 3)
Appendices
A-9
A
A-10
Appendices
6
3
4
Rosemount Analytical Inc.
PLATE
WELDED
TO STACK
4.026
(102.26)
I.D.
02 03 04
11 12 13
14 15 16
C 9 FT (2743.2) GAS TUBE PICK-UP
B 6 FT (1828.8) GAS TUBE PICK-UP
GAS TUBE PICK-UP
GROUP NOTE
A 3 FT (914.4)
ELECT
CABLE
73.0 (1854.2) ON 6 FT (1828.8) PICKUP (3D390004G08)
37.0 (939.8) ON 3 FT (914.4) PICKUP (3D390004G07)
109.0 (2768.6) ON 9 FT (2743.2) PICKUP (3D390004G09)
62.5 (1587.5) ON 9 FT (2743.2) PICKUP (3D390004G09)
26.5 (673.1) ON 3 FT (914.4) OR 6 FT (1828.8)
PICKUP (3D390004G07 OR G08)
WELD BY CUSTOMER
GASKET
AND
HARDWARE
06 07 08
FLANGE
05 09 10
01
6.50 (165.1) REF
DRAIN
A
VIEW
27270018
A-A
DIRECTION
OF FLOW
REF
1 AIR
CAL
2 GAS
NOTES: 1. REFERENCE AIR SUPPLY CONNECTION BITE TYPE FITTING (PARKER CPI) FOR
0.250 O.D. TUBING. 2 SCFH AT 3 PSIG (20.69 kPa GAUGE) MAX. CLEAN DRY AIR
REQUIRED. FITTING IS LOCATED ON FAR SIDE.
2. CALIBRATION AND PURGE GAS CONNECTION. BITE TYPE FITTING (PARKER CPI)
10 SCFH AT 32 PSIG (220.64 kPa GAUGE) MAX. CALIBRATION GAS REQUIRED.
3. LAG TO ENSURE GAS TEMPERATURE DOES NOT GO BELOW DEW POINT OR
EXCEED 932oF (500oC).
4. INSTALL WITH ANALYZER IN A VERTICALLY DOWNWARDS DIRECTION ONLY.
5. FLUE GAS OPERATING TEMPERATURE RANGE 1200o TO 1800oF (650 o TO 980oC).
6. RECOMMENDED 2.0 INCH (50.8) THK INSULATION. THERMAL CONDUCTIVITY K EQUAL
0.5 FOR INSULATION.
7. DIMENSIONS ARE IN INCHES WITH MILLIMETERS IN PARENTHESES.
Appendix A Rev. 3.6
July 1998
IF EQUIPPED WITH THE OPTIONAL
CERAMIC DIFFUSOR ASSEMBLY, PROBE
ASSEMBLY MUST BE ORIENTED SO THAT
VEE SHIELD IS SQUARE TO GAS FLOW.
19.80
(502.92)
FOR
3D3947G01
27.31 (693.67)
CLEARANCE REQ
FOR PROBE
INSERTION
AND REMOVAL
A
20 FT (6.1 M)
STD CABLE
Instruction Manual
World Class 3000
Figure A-13. Bypass Probe Option (Sheet 2 of 3)
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
Extended Temperature By-Pass Arrangements (2400°°F; 1300°°C)
PART NO.
GROUP
CODE
DESCRIPTION
1U0571
G01
3’ By-pass Package with ANSI bolt pattern.
1U0571
G02
6’ By-pass Package with ANSI bolt pattern.
1U0571
G03
9’ By-pass Package with ANSI bolt pattern.
1U0571
G04
3’ By-pass Package with JIS bolt pattern.
1U0571
G05
6’ By-pass Package with JIS bolt pattern.
1U0571
G06
9’ By-pass Package with JIS bolt pattern.
1U0571
G07
3’ By-pass Package with DIN bolt pattern.
1U0571
G08
6’ By-pass Package with DIN bolt pattern.
1U0571
G09
9’ By-pass Package with DIN bolt pattern.
Figure A-13. Bypass Probe Option (Sheet 3 of 3)
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
A-11
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
PROBE TROUBLESHOOTING
A-7
OVERVIEW
1. The system does not respond to
changes in the oxygen concentration.
The probe troubleshooting section describes
how to identify and isolate faults which may develop in the probe assembly.
2. The system responds to oxygen
changes but does not give the correct
indication.
3. The system does not give an acceptable indication of the value of the oxygen calibration gas being applied
during calibration.
Install all protective equipment and
safety ground leads after troubleshooting. Failure to replace covers
and ground leads could result in serious injury or death.
A-8
PROBE TROUBLESHOOTING
4. The system takes a long time to return
to the flue gas value after the calibration gas is turned off.
b. Table A-2 provides a guide to fault finding
for the above symptoms.
a. Probe Faults
Listed below are the four symptoms of
probe failure.
c. Figure A-14 and Figure A-15 provide an alternate approach to finding probe related
problems.
Table A-2. Fault Finding
Symptom
Check
Fault
Remedy
1. No response to oxygen concentration
change when:
Heater is cold and TC
mV output is less than
set point
Heater is hot and T/C
mV output is at set
point ±0.2 mV
A-12
Appendices
Thermocouple continuity
Thermocouple failure
Replace thermocouple
or return probe to
Rosemount.
Heater cold resistance to
be 11 ohm to 14 ohm
Heater failure
Replace heater or return
probe to Rosemount.
Triac O/P to heater
Failure of electronics
Check HPS and electronics package.
Recorder chart
Recorder failure
See Recorder Instruction
Manual.
Cell mV input to electronics and cell mV at probe
junction box
No cell mV at probe when
calibration gas applied
Replace cell or return
probe to Rosemount.
Probe cell mV OK but no
input to electronics
Check out cable
connection.
Cell mV satisfactory both
at probe junction box and
input to electronics - failure of electronics
Check electronics
package.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
Table A-2. Fault Finding (Continued)
Symptom
Check
Fault
Remedy
2. System responds to
oxygen concentration
changes but does not
give correct indication
Good response, with
incorrect indication
3. System does not give
accurate indication of
applied calibration gas
4. System takes a long
time to return to flue
gas value after calibration gas is turned off
Rosemount Analytical Inc.
Recorder or remote
indicator
Calibration error
Recalibrate recorder or
indicator. Reference Recorder Instruction Manual.
System calibration
Calibration error
Recalibrate system.
Probe mounting and condition of duct
Air ingress into duct
Stop air leaks or resite
probe.
Cell mV input to
electronics
Failure of electronics
Check electronics
package.
Calibration gas input port
Blocked port
Clean port. If the flue gas
is condensing in the calibration gas line, insulate
the back of the probe.
Make sure that the calibration gas line is capped
between calibrations, or a
check valve is installed.
Ceramic diffusion element
Diffusion element cracked, Replace diffusion element.
broken, or missing
Diffusion element
Plugged diffusion element
A Division of Emerson Process Management
Change diffusion element
or snubber diffusion
element.
Appendices
A-13
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
Figure A-14. Flowchart of Probe Related Problems, #1
A-14
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
World Class 3000
Appendix A Rev. 3.6
July 1998
Figure A-15. Flowchart of Probe Related Problems, #2
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
A-15
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
SERVICE AND NORMAL MAINTENANCE
!
NOTE
UPON COMPLETING INSTALLATION, MAKE SURE THAT THE PROBE IS TURNED ON AND OPERATING
PRIOR TO FIRING UP THE COMBUSTION PROCESS. DAMAGE CAN RESULT FROM HAVING A COLD
PROBE EXPOSED TO THE PROCESS GASES.
During outages, and if possible, leave all probes running to prevent condensation and premature aging from thermal cycling.
If the ducts will be washed down during outage, MAKE SURE to power down the probes and
remove them from the wash area.
A-9
OVERVIEW
This section describes routine maintenance of
the oxygen analyzer probe. Spare parts referred
to are available from Rosemount. Probe disassembly kit 3535B42G01 contains the required
spanner and hex wrenches. Refer to the following section of this appendix for part numbers
and ordering information.
Install all protective equipment covers
and safety ground leads after equipment repair or service. Failure to install covers and ground leads could
result in serious injury or death.
precise surface finishes. Do not remove items
from packaging until they are ready to be used.
Spanner wrenches and hex wrenches needed for
this procedure are part of an available special
tools kit, Table A-3.
Wear heat resistant gloves and clothing to remove probe from stack. Normal operating temperatures of diffusor
and vee deflector are approximately
600° to 800°F (316° to 427°C). They
could cause severe burns.
Disconnect and lock out power before
working on any electrical components.
There is voltage up to 115 Vac.
A-10 PROBE RECALIBRATION
The oxygen analyzer system should be calibrated when commissioned. Under normal circumstances the probe will not require frequent
calibration. When calibration is required, follow
the procedure described in the Instruction Bulletin applicable to your electronics package.
Do not remove cell unless it is certain
that replacement is needed. Removal
may damage cell and platinum pad. Go
through complete troubleshooting
procedure to make sure cell needs replacement before removing it.
A-11 CELL REPLACEMENT
This paragraph covers oxygen sensing cell replacement. Do not attempt to replace the cell
until all other possibilities for poor performance
have been considered. If cell replacement is
needed, order cell replacement kit, Table A-3.
The cell replacement kit contains a cell and
flange assembly, corrugated seal, setscrews,
socket head cap screws, and anti-seize compound. Items are carefully packaged to preserve
A-16
Appendices
a. Disconnect and lock out power to electronics. Shut off and disconnect reference air
and calibration gas supplies from probe
junction box, Figure A-16. Wearing heat resistant gloves and clothing, remove probe
assembly from stack carefully and allow to
cool to room temperature. Do not attempt to
work on unit until it has cooled to a comfortable working temperature.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
INCONEL
CELL WIRE
(CLEAR
SLEEVING)
HEATER
WIRES
(BLACK
SLEEVING)
THERMOCOUPLE (RED ALUMEL)
BOMB TAIL
CONNECTOR
CELL EXTENSION
WIRE (ORANGE)
THERMOCOUPLE +
(YELLOW CHROMEL)
CALIBRATION
GAS FITTING
REFERENCE
AIR FITTING
CABLE
PROBE JUNCTION
BOX COVER
27270019
Figure A-16. Cell Wiring Connection
b. If the probe uses the standard diffusion
element, use a spanner wrench to remove
the diffusion element.
c. If equipped with the optional ceramic diffusor
assembly, remove and discard setscrews,
Figure A-17, and remove vee deflector. Use
spanner wrenches from probe disassembly
kit, Table A-3, to turn hub free from retainer.
Inspect diffusion element. If damaged, replace element.
d. Loosen four socket head cap screws from
the cell and flange assembly and remove
the assembly and the corrugated seal. The
cell flange has a notch which may be used
Rosemount Analytical Inc.
A Division of Emerson Process Management
to gently pry the flange away from the
probe. Note that the contact pad inside the
probe will sometimes fuse to the oxygen
sensing cell. If the cell is fused to the contact pad, push the cell assembly back into
the probe (against spring pressure), and
quickly twist the cell assembly. The cell and
contact pad should separate. If the contact
pad stays fused to the cell, a new contact/thermocouple assembly must be installed. Disconnect the cell and the
thermocouple wires at the probe junction
box, and withdraw the cell with the wires still
attached (see paragraph A-13).
Appendices
A-17
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
RETAINER
PIN
WRENCH
g. Rub a small amount of anti-seize on both
sides of new corrugated seal.
OPTIONAL CERAMIC
DIFFUSION ELEMENT
h. Assemble cell and flange assembly, corrugated seal, and probe tube. Make sure the
calibration tube lines up with the calibration
gas passage in each component. Apply a
small amount of anti-seize compound to
screw threads and use screws to secure
assembly. Torque to 55 in-lbs (4 N•m).
SETSCREW
HUB
CEMENT
PORT
CEMENT
FILLET
i.
Apply anti-seize compound to threads of
cell assembly, hub, and setscrews. Reinstall
hub on cell assembly. Using pin spanner
wrenches, torque to 10 ft-lbs (14 N•m). If
applicable, reinstall vee deflector, orienting
apex toward gas flow. Secure with
setscrews and anti-seize compound.
Torque to 25 in-lbs (2.8 N•m).
j.
On systems equipped with an abrasive
shield, install dust seal gaskets, with joints
o
180 apart.
VEE
DEFLECTOR
21240026
Figure A-17. Removal of Optional Diffusor
and Vee Deflector
PROBE TUBE
(NOT INCLUDED
IN KIT)
CORRUGATED
SEAL
CELL AND
FLANGE
ASSEMBLY
SOCKET HEAD
CAP SCREWS
CALIBRATION GAS
PASSAGE
21240009
Figure A-18. Cell Replacement Kit
e. If contact assembly is damaged, replace
contact and thermocouple according to
paragraph A-13, Replacement of Contact
and Thermocouple Assembly.
f.
A-18
Remove and discard corrugated seal. Clean
mating faces of probe tube and retainer.
Remove burrs and raised surfaces with
block of wood and crocus cloth. Clean
threads on retainer and hub.
Appendices
k. Reinstall probe and gasket on stack flange.
If there is an abrasive shield in the stack,
make sure dust seal gaskets are in place as
o
they enter 15 reducing cone.
l.
Turn power on to electronics and monitor
thermocouple output. It should stabilize at
29.3 ±0.2 mV. Set reference air flow at 2 scfh
(56.6 L/hr). After probe stabilizes, calibrate
probe per Instruction Bulletin applicable to
your electronics package. If new components
have been installed, repeat calibration after
24 hours of operation.
A-12 OPTIONAL CERAMIC DIFFUSION
ELEMENT REPLACEMENT
a. General
The diffusion element protects the cell from
particles in process gases. It does not normally need to be replaced because the vee
deflector protects it from particulate erosion.
In severe environments the filter may be
broken or subject to excessive erosion. Examine the diffusion element whenever removing the probe for any purpose. Replace
if damaged.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
World Class 3000
Damage to the diffusion element may become apparent during calibration. Compare
probe response with previous response. A
broken diffusion element will cause a slower
response to calibration gas.
Hex wrenches needed to remove setscrews
and socket head screws in the following procedure are available as part of a special tool
kit, Table A-3.
Wear heat resistant gloves and clothing to remove probe from stack. Normal operating temperatures of diffusor
and vee deflector are approximately
600° to 800°F (300° to 425°C). They can
cause severe burns.
Disconnect and lock out power before
working on any electrical component.
There is voltage up to 115 Vac.
Appendix A Rev. 3.6
July 1998
3. On systems equipped with abrasive
shield, remove dual dust seal gaskets.
4. Use spanner wrenches from special
tools kit, Table A-3, to turn hub free
from retainer.
5. Put hub in vise. Break out old diffusion
element with chisel along cement line
and 3/8 inch (9.5 mm) pin punch
through cement port.
6. Break out remaining diffusion element
by tapping lightly around hub with
hammer. Clean grooves with pointed
tool if necessary.
7. Replace diffusion element, using replacement kit listed in Table A-3. This
consists of a diffusion element, cement, setscrews, anti-seize compound
and instructions.
8. Test fit replacement element to be sure
seat is clean.
It is not necessary to remove the cell
unless it is certain that replacement is
necessary. Cell cannot be removed for
inspection without damaging it. Refer
to paragraph A-11, Cell Replacement.
b. Replacement Procedure
1. Shut off power to electronics. Disconnect cable conductors and remove cable, Figure A-16. Shut off and
disconnect reference air and calibration
gas supplies from probe junction box.
Wearing heat resistant gloves and
clothing, carefully remove probe assembly from stack and allow to cool to
room temperature. Do not attempt to
work on unit until it has cooled to a
comfortable working temperature.
2. Loosen setscrews, Figure A-17, using
hex wrench from special tools kit,
Table A-3, and remove vee deflector.
Inspect setscrews. If damaged, replace
with M-6 x 6 stainless setscrews
coated with anti-seize compound.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Do not get cement on diffusion element except where it touches the hub.
Any cement on ceramic element
blocks airflow through element. Wiping wet cement off of ceramic only
forces cement into pores.
9. Thoroughly mix cement and insert tip
of squeeze bottle into cement port. Tilt
bottle and squeeze while simultaneously turning diffusion element into
seat. Do not get any cement on upper
part of diffusion element. Ensure complete penetration of cement around
three grooves in hub. Cement should
extrude from opposite hole. Wipe excess material back into holes and wipe
top fillet of cement to form a uniform
fillet. (A Q-Tip is useful for this.) Clean
any excess cement from hub with
water.
10. Allow filter to dry at room temperature
overnight or 1 to 2 hours at 200°F
(93°C).
Appendices
A-19
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
Squeezing tabs on hose clamps, remove
hoses from probe junction box, Figure A-19.
Remove four screws in corners of probe
junction box. Pull probe junction box and inner probe assembly free from probe tube.
Set on bench and allow to cool to room
temperature.
11. Wipe a heavy layer of anti-seize compound onto the threads and mating
surfaces of the diffusion hub and
retainer.
12. Assemble retainer and diffusion hub
with two pin spanner wrenches. Torque
to 10 ft-lbs (14 N·m).
13. On systems equipped with abrasive
shield, install dust seal gaskets with
joints 180° apart.
14. Reinstall vee deflector, orienting apex
toward gas flow. Apply anti-seize compound to setscrews and tighten with
hex wrench.
15. Reinstall probe on stack flange.
16. Turn power on to electronics and
monitor thermocouple output. It should
stabilize at 29.3 ±0.2 mV. Calibrate
probe per Instruction Bulletin applicable to your electronics package.
b. Disconnect cell extension wire (orange),
thermocouple wire (red alumel), and thermocouple wire (yellow chromel) by cutting
bomb tail connections from the terminal
strip, Figure A-16.
c. Remove two screws, Figure A-19, lockwashers, and flat washers that connect
probe junction box to inner probe assembly.
Pull heater, V-strut and backplate assembly
away from probe junction box. Inspect all
O-rings and insulating gasket; replace if worn
or damaged.
PROBE JUNCTION BOX TO HEATER,
STRUT, AND BACKPLATE
ASSEMBLY SCREW
PROBE JUNCTION BOX
INNER PROBE ASSEMBLY
TO PROBE TUBE SCREWS
A-13 REPLACEMENT OF CONTACT AND
THERMOCOUPLE ASSEMBLY
PROBE
JUNCTION
BOX
Use heat resistant gloves and clothing when removing probe junction box
and inner probe assembly. Do not attempt to work on these components
until they have cooled to room temperature. Probe components can be as
hot as 800°F (427°C). This can cause
severe burns.
HOSE
CLAMP
HOSE
Disconnect and lock out power before
working on any electrical components.
There is voltage up to 115 Vac.
21240027
a. Disconnect and lock out power to electronics. Using heat resistant gloves and clothing, remove probe junction box cover.
A-20
Appendices
Figure A-19. Probe Junction Box Mechanical
Connections
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
d. Use a pencil to mark locations of spring clip
on ceramic rod, Figure A-20.
g. Note wire lengths of old assembly as an aid
for trimming new lengths in step (j). Trimming of wires will not always be necessary.
Throw away old contact and thermocouple
assembly.
e. Pry or squeeze tabs on spring clips, and pull
contact and thermocouple assembly out of
probe assembly. Retain spring clips and
spring; replace if damaged.
h. Carefully guide new contact and thermocouple assembly through V-strut assembly
leaf spring (4, Figure A-21), spring (9),
spring clip (10) (held open by squeezing
tabs), and tube supports (11, 13) until
spring clip reaches pencil mark.
Be very careful when handling contact
and thermocouple assembly. The ceramic rod in this assembly is fragile.
f.
i.
While very carefully handling new contact
and thermocouple assembly, lay old assembly next to new one. Transfer pencil
marks to new rod.
HEATER SCREWS
CONTACT AND
(NOT SHOWN)
THERMOCOUPLER
ASSEMBLY
MOUNTING SCREW
V-STRUT
(REAR VIEW)
Do not trim new wiring shorter than
existing (old) wiring. Excessive wire
trim will prevent connections from
being properly made and will require a
new replacement kit.
j.
INSULATING
GASKET
SPRING
CLIP
Reinstall insulating gasket on backplate, replace two screws, O-rings, lockwashers and
flat washers connecting probe junction box
to inner probe assembly.
HEATER
CERAMIC ROD
Trim wires, if necessary, as noted in
step (g).
k. Connect color coded wires to proper terminals as shown in Figure A-16. Rosemount
recommends connecting the thermocouple
wires directly to the terminal strip. This is
because the junction of different metals at
the wires and lugs and at the lugs and the
21240010
Figure A-20. Inner Probe Replacement
(Heater, V-Strut, and Backplate Assembly)
3
1
4
4
5
6
13
2
11
11
10
9
7
8
12
8
1.
2.
3.
4.
Heater Ceramic Rod
Contact and Thermocouple Assembly
Strut
Leaf Spring
5.
6.
7.
8.
Ring Lug
Butt Connector
Extension
Backplate
9.
10.
11.
12.
13.
Spring
Spring Clip Assembly
Common Tube Support
Heater
Short Tube Support
Figure A-21. Heater, Strut, and Backplate Assembly
(Inner Probe Assembly)
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
A-21
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
terminal strip could act as additional thermocouple junctions. This could produce a
voltage that would affect the thermocouple
output signal.
Do not bend wires closer than 1/4 inch
(6.4 mm) from end of ceramic rod. Dress
wires so they do not touch sides of probe
junction box.
l.
Slide assembled probe junction box and inner probe assembly into probe tube. To
align calibration gas tube with corresponding hole in backplate (A, B, Figure A-1), insert scriber through hole in backplate and
into calibration gas tube. Secure with
screws. Reinstall hoses and probe junction
box cover.
m. Power up system. Monitor thermocouple
output. It should stabilize at set point mV
±0.2 mV. Recalibrate probe per Instruction
Bulletin applicable to your electronics
package.
A-14 REPLACEMENT OF HEATER, V-STRUT
AND BACKPLATE ASSEMBLY (INNER
PROBE ASSEMBLY; INCLUDES CONTACT
AND THERMOCOUPLE ASSEMBLY)
Use heat resistant gloves and clothing
when removing probe junction box
and inner probe assembly. Do not attempt to work on these components
until they have cooled to room temperature. Probe components can be as
hot as 800° (427°C). This can cause
severe burns.
Disconnect and lock out power before
working on any electrical components.
There is voltage up to 115 Vac.
a. Disconnect and lock out power to electronics. Using heat resistant gloves and clothing, remove probe cover. Squeezing tabs
on hose clamps and remove hoses from
probe junction box, Figure A-19. Remove
four screws and lockwashers (7, 10, Figure
A-22) that hold probe junction box and inner
probe assembly to probe tube. Pull probe
junction box and inner probe assembly free
from probe tube. Set on bench and allow to
cool to room temperature.
b. Disconnect cell extension wire (orange),
thermocouple wire (red alumel), and thermocouple wire (yellow chromel) by cutting
bomb tail connections from the terminal
strip, Figure A-16.
c. Remove two screws, lockwashers, and flat
washers that connect probe junction box to
inner probe assembly. Remove and discard
inner probe assembly (heater, V-strut, and
backplate assembly). Replace with new inner probe assembly. Reinstall screws, lockwashers and flat washers.
d. Connect color coded wires to proper terminals as shown in Figure A-16. Rosemount
recommends connecting the thermocouple
wires directly to the terminal strip. This is
because the junction of different metals at
the wires and lugs and at the lugs and the
terminal strip could act as additional thermocouple junctions. This could produce a
voltage that would affect the thermocouple
output signal.
Do not bend wires closer than 1/4 inch
(6.4 mm) from end of ceramic rod. Dress
wires so they do not touch sides of probe
junction box.
NOTE
This replacement may be done without
removing the probe from the duct.
A-22
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
6
1
2
4
7
8
9
5
11
10
3
21240012
1.
2.
3.
4.
5.
Snubber Diffusion Element
Socket Hd Cap Screw [0.25 in.-28 x 0.063 (16 mm)]
Cell and Flange Assembly
Corrugated Seal
Probe Tube Assembly
6.
7.
8.
9.
10.
11.
Gasket [4.0 in. (102 mm) x 4.0 in. x 0.12 in. (3 mm)]
Fillister Hd Screw [8-32 x 0.5 in. (12.7 mm)]
Cover Head Assembly
Hose Clamp
Lockwasher (#8 Split)
Heater Strut Assembly
Figure A-22. Oxygen Analyzer (Probe), Cross-Sectional View
e. Slide assembled probe junction box and inner probe assembly into probe tube. To
align calibration gas tube with corresponding hole in backplate (A, B, Figure A-1), insert aligning tool (included in probe
disassembly kit, P/N 3535B42G01) through
hole in backplate and into calibration gas
tube, while sliding the heater strut into the
probe tube. Secure with screws. Reinstall
hoses and probe junction box cover.
f.
Power up system. Monitor thermocouple
output. It should stabilize at set point ±0.2
mV. Recalibrate probe per Instruction Bulletin applicable to your electronics package.
A-15 CALIBRATION GAS AND REFERENCE AIR
LINES FOR HIGH TEMPERATURE CORROSIVE ENVIRONMENT OPERATION
A high temperature, corrosive environment kit is
available when the probe is exposed to these
types of operating conditions. The kit includes
stainless steel tubing and teflon fittings for inside the probe junction box. The kit part number
is 4843B93G01.
Rosemount Analytical Inc.
A Division of Emerson Process Management
a. Installation Procedure
Use heat resistant gloves and
clothing when removing probe junction box and inner probe assembly.
Do not attempt to work on these components until they have cooled to
room temperature. Probe components
can be as hot as 800°F (427°C). This
can cause severe burns.
Disconnect and lock out power before
working on any electrical components.
There is voltage up to 115 Vac.
1. Disconnect and lock out power to digital electronics. Using heat resistant
gloves and clothing, remove probe
cover. Squeezing tabs on hose clamps,
remove hoses from probe junction box
(Figure A-19).
Appendices
A-23
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
TEFLON
SLEEVES
Do not use sealant when installing the
stainless steel tubes. Gas samples
may become contaminated.
2. First install the stainless steel tubing on
the fitting at the bottom of the probe
junction box. Install the other end of the
stainless steel tube onto the tube going
to the probe (Figure A-23).
NOTE
STAINLESS
STEEL
TUBING
If abrasive conditions of high ash content and high velocity exist, an abrasive shield is recommended. To
balance out the wear on the shield, rotate the shield 90° every time the
probe is powered down for service.
21240028
Figure A-23. High Temperature - Corrosive
Environment Kit
A-24
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
REPLACEMENT PARTS
Table A-3. Replacement Parts for Probe
Figure and
Index No.
Figure A-20
Figure A-20
Figure A-20
Figure A-20
Figure A-20
Figure A-21, 2
Figure A-21, 2
Figure A-21, 2
Figure A-21, 2
Figure A-21, 2
Figure A-7
Figure A-7
Figure A-7
Figure A-7
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-18
Figure A-10
Figure A-8
Part Number
1
3D39441G06
1
3D39441G07
1
3D39441G08
1
3D39441G09
1
3D39441G10
2
3534B56G04
2
3534B56G05
2
3534B56G06
2
3534B56G07
2
3534B56G08
3
3D39003G01
3
3D39003G02
3
3D39003G07
3
3D39003G08
4847B61G01
4847B61G02
4847B61G03
4847B61G04
4847B61G05
4847B61G06
4847B61G07
4847B61G08
4847B61G09
4847B61G10
4847B61G11
4847B61G12
4847B61G13
4847B61G14
4847B61G15
4847B61G16
4847B61G17
4847B61G18
3535B42G01
3534B18G01
3535B60G01
Rosemount Analytical Inc.
Description
Heater, V-Strut, and Backplate Assembly, 18 in. (45.6 cm)
Heater, V-Strut, and Backplate Assembly, 3 ft (0.9 m)
Heater, V-Strut, and Backplate Assembly, 6 ft (1.8 m)
Heater, V-Strut, and Backplate Assembly, 9 ft (2.7 m)
Heater, V-Strut, and Backplate Assembly, 12 ft (3.6 m)
Contact and Thermocouple Assembly, 18 in. (45.6 cm)
Contact and Thermocouple Assembly, 3 ft (0.9 m)
Contact and Thermocouple Assembly, 6 ft (1.8 m)
Contact and Thermocouple Assembly, 9 ft (2.7 m)
Contact and Thermocouple Assembly, 12 ft (3.6 m)
Abrasive Shield Assembly, 3 ft (0.9 m)
Abrasive Shield Assembly, 6 ft (1.8 m)
Abrasive Shield Assembly, 9 ft (2.7 m)
Abrasive Shield Assembly, 12 ft (3.6 m)
Cell Replacement Kit, ANSI, No Lead Wire
Cell Replacement Kit, ANSI 18 in. (45.6 cm)
Cell Replacement Kit, ANSI 3 ft (0.9 m)
Cell Replacement Kit, ANSI 6 ft (1.8 m)
Cell Replacement Kit, ANSI 9 ft (2.7 m)
Cell Replacement Kit, ANSI 12 ft (3.6 m)
Cell Replacement Kit, JIS, No Lead Wire
Cell Replacement Kit, JIS 18 in. (45.6 cm)
Cell Replacement Kit, JIS 3 ft (0.9 m)
Cell Replacement Kit, JIS 6 ft (1.8 m)
Cell Replacement Kit, JIS 9 ft (2.7 m)
Cell Replacement Kit, JIS 12 ft (3.6 m)
Cell Replacement Kit, DIN, No Lead Wire
Cell Replacement Kit, DIN 18 in. (45.6 cm)
Cell Replacement Kit, DIN 3 ft (0.9 m)
Cell Replacement Kit, DIN 6 ft (1.8 m)
Cell Replacement Kit, DIN 9 ft (2.7 m)
Cell Replacement Kit, DIN 12 ft (3.6 m)
Probe Disassembly Kit
Diffuser Assembly
Diffuser Dust Seal Hub Assembly
(For use with Abrasive Shield)
A Division of Emerson Process Management
Appendices
A-25
A
Instruction Manual
Appendix A Rev. 3.6
July 1998
World Class 3000
Table A-3. Replacement Parts for Probe (Continued)
Figure and
Index No.
Part Number
Figure A-10
Figure A-9
Figure A-11
Figure A-4
4841B03G02
3535B63G01
3535B62G01
3534B48G01
Figure A-17
6292A74G02
1537B70G03
Figure A-23
Figure A-1, 2
Figure A-12
4843B93G01
4843B37G01
4843B38G02
Description
Stainless Steel Diffuser Assembly
Flame Arrestor Diffuser Dust Seal
Flame Arrestor Diffuser
Vee Deflector Assembly
(For use with standard or dust seal type ceramic diffusers)
Diffusion Element Replacement Kit
Horizontal and Vertical Brace Clamp Assembly,
9 and 12 foot (2.7 and 3.6 m) probe
High Temperature - Corrosive Environment Kit
Snubber Diffusion Assembly
Dust Seal/Snubber Diffusion Assembly
1
Heater, V-strut, and backplate assembly includes contact and thermocouple assembly.
Contact and thermocouple assembly includes platinum pad and inconel wire.
3
Abrasive shield assembly includes accessories necessary for its use and a mounting plate and gasket.
2
A-26
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
APPENDIX B, REV. 2.2
HPS 3000 HEATER POWER SUPPLY
B
DESCRIPTION
Read the “Safety instructions for the
wiring and installation of this apparatus” at the front of this Instruction
Bulletin. Failure to follow the safety
instructions could result in serious
injury or death.
B-1
DESCRIPTION
The Rosemount HPS 3000 Heater Power Supply Field Module acts as an interface between
probe and electronics, and supplies power to
the probe heater. The unit allows the use of
probes with a number of different electronics
packages.
The HPS is available in a NEMA 4X (IP56)
non-hazardous enclosure or an optional
Class 1, Division 1, Group B (IP56) explosion-proof enclosure, Figure B-1.
The heater power supply, Figure B-2, consists
of a mother board, daughter board, and a
transformer for supplying correct voltage to the
probe heater. The mother and daughter boards
contain terminal strips for connecting probe,
electronics, and power supply.
The HPS is jumper configurable for 120, 220, or
240 Vac. For 100 Vac usage, the HPS is factory-supplied with a special transformer. The
100 Vac transformer can also be easily field installed. Refer to paragraph B-7, Transformer
Replacement for installation procedure; refer to
Table B-2, for transformer part numbers.
35730001
Figure B-1. HPS 3000 Heater Power Supply Field Module
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
B-1
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
TRANSFORMER
TERMINAL
COVERS
FRONT
TERMINAL STRIP
(FROM ELECTRONICS)
TRANSFORMER
TERMINAL STRIP
(FROM PROBE)
SIDE
35730002
Figure B-2. Heater Power Supply, Interior
B-2
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
Table B-1. Specifications for Heater Power Supply
Environmental Classification ..................................................NEMA 4X (IP56) Optional - Class 1, Division 1,
Group B (IP56)
Electrical Classification ..........................................................Category II
Humidity Range .....................................................................95% Relative Humidity
Ambient Temperature Range ................................................-20° to 140°F (-30° to 60°C)
Vibration .................................................................................5 m/sec2, 10 to 500 xyz plane
Cabling Distance Between HPS 3000 and Probe ..................Maximum 150 feet (45 m)
Cabling Distance Between HPS 3000 and CRE 3000 ...........Maximum 1200 feet (364 m)
Cabling Distance Between HPS 3000 and IFT 3000 ............Maximum 1200 feet (364 m)
Approximate Shipping Weight ................................................12 pounds (5.4 kg)
B-2
THEORY OF OPERATION
The HPS 3000 Heater Power Supply may perform slightly different functions, depending upon
which electronics package it is used with. Figure
B-3 shows a functional block diagram of the
unit. The HPS contains a transformer for converting line voltage to 44 volts needed to power
the probe heater. The relay, Figure B-3, can be
used to remotely turn the probe on or off manually. A triac module is used to turn the heater on
or off, depending on probe temperature.
When used with the CRE 3000 Control Room
Electronics or IFT 3000 Intelligent Field Transmitter, the HPS uses a cold junction temperature compensation feature. This allows for the
B
use of a less expensive cable between the HPS
and CRE or HPS and IFT. The HPS and electronics package can be located up to 1200 feet
(364 m) apart.
The standard cable, between probe and HPS, is
thermocouple compensated. This prevents the
additional junctions between thermocouple and
cable from producing a voltage which would affect the thermocouple output signal. A temperature sensor in the HPS monitors the
temperature at the junction and sends a voltage
signal to the CRE and IFT. The CRE and IFT
uses this signal to compensate the probe thermocouple reading for the temperature at the
junction between the compensated and uncompensated cables.
LINE
TO HEATER
RELAY
TRIAC
FROM
IFT
AD590
TO
PROBE
PROBE TC
PROBE TC
STACK TC
STACK TC
CELL MV
CELL
686015
Figure B-3. Heater Power Supply Block Diagram
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
B-3
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
NOTE
In operation, when connected to the CRE 3000
Control Room Electronics, line voltage passes
through the relay (when on) and is converted
into 44 volts by the transformer. If the probe
thermocouple indicates that the probe has
dropped below operating temperature, a signal
from the CRE triggers the triac. The triac then
supplies voltage to the probe heater, warming
the cell. Conversely, if the probe thermocouple
indicates that the probe heater has reached the
upper limit of operating temperature, the CRE
deactivates the triac, shutting off power to the
heater.
When using the HPS 3000 with an existing electronics package, such as
Models 218, 218A, 225, or TC200, the
electronics will not have the input/output capacity to support all of
the functions mentioned in this section. Refer to Instruction Bulletin IB106-300NE.
HPS 3000 TROUBLESHOOTING
B-3
OVERVIEW
The HPS 3000 troubleshooting section describes how to identify and isolate faults which
may develop in the HPS 3000 assembly.
B-4
HPS 3000 TROUBLESHOOTING
The HPS 3000 troubleshooting may overlap
with the probe in use in the system. Faults in
either system may cause an error to be displayed in the electronics package. Figure B-4,
Figure B-5, and Figure B-6 provide troubleshooting information.
Install all protective equipment covers
and safety ground leads after troubleshooting. Failure to replace covers
and ground leads could result in serious injury or death.
B-4
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
SYMPTOM
HEATER DOES NOT HEAT
UP (DOES NOT INCREASE
IN OUTPUT).
SET METER TO 250 VAC.
PLACE METER PROBES ON
J2, “FROM ELECTRONICS”,
ANALOG HEATER.
SET METER* FOR 50 VAC.
PLACE PROBES ON
TERMINAL BLOCK J2,
“FROM PROBE”, PROBE
HEATER.
METER SHOULD REGISTER
A PULSATING NOMINAL
115 VAC.
B
NO
CHECK FUSES IN PROBE
ELECTRONICS.
YES
METER INDICATES
PULSATING NOMINAL
44 VAC.
NO
DISCONNECT POWER TO
HPS AND PROBE
ELECTRONICS. CHECK
ALL FOUR FUSES IN HPS.
IF FUSES OK, POSSIBLE
PROBE ELECTRONICS TRIAC
FAILURE.
YES
DISCONNECT POWER FROM
HPS & PROBE ELECT. SET
METER ON RX1.
FUSES BLOWN IN HPS.
NO
CHECK JUMPER JM2 IS
INSTALLED.
YES
CHECK THAT LINE VOLTAGE
IS CORRECT BY SELECTING
CORRECT JUMPERS
ACCORDING TO CHART ON
INSIDE OF HPS COVER.
MEASURE RESISTANCE OF
HEATER BY PLACING
PROBES ON TERMINAL
BLOCK J2, “FROM PROBE”,
PROBE HEATER.
RESISTANCE MEASURED
SHOULD BE NOMINALLY
12 OHMS.
NO
YES
POSSIBLE TRIAC FAILURE.
REPLACE HPS
MOTHERBOARD.
*SIMPSON MODEL 260 OR
EQUIVALENT MULTIMETER.
REPLACE BLOWN FUSES.
HEATER IS OPEN.
REPLACE HEATER.
35730004
Figure B-4. HPS Troubleshooting Flowchart, #1
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
B-5
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
SYMPTOM
HEATER OVERHEATS.
NOTE: ON INITIAL STARTUP THE
TEMPERATURE OF THE PROBE MAY
OVERHEAT TO A NOMINAL TEMP OF
800°C.
CHECK IF THE YELLOW WIRE IS CONNECTED
TO POSITIVE AND THE RED TO NEGATIVE
ON BOTH “FROM ELECTRONICS” AND “FROM
PROBE” TERMINAL BLOCKS. (MODELS 218
AND 225 ONLY)
NO
CONNECT THE WIRING
ACCORDING TO THE
DECALS ON THE TERMINAL
COVERS.
SET METER* ON 250 VAC SCALE.
CHECK “FROM ELECTRONIC”, ANALOG
HEATER TERMINALS IF THERE IS A
PULSATING NOMINAL 115 VAC.
NO
IF THE VOLTAGE IS
CONSTANTLY ON, THEN
THE TRIAC IN THE PROBE
ELECTRONICS IS SHORTED.
YES
SET METER* ON 50 VAC SCALE.
CHECK “FROM PROBE”, TERMINALS AT
PROBE HEATER IF THERE IS A PULSATING
NOMINAL 44 VOLTS.
NO
IF THE VOLTAGE IS
CONSTANTLY ON, THEN
THE TRIAC MODULE IN
THE HPS IS SHORTED.
YES
CHECK PROBE ELECTRONICS SETPOINT
HAS BEEN CHANGED ACCORDING TO
APPLICABLE ELECTRONICS PACKAGE IB.
YES
CHECK IF PROBE HEATER VOLTAGE
SELECTION JUMPER JM7 INSTALLED
(REMOVE JM8).
35730003
*SIMPSON MODEL 260 OR EQUIVALENT MULTIMETER.
Figure B-5. HPS Troubleshooting Flowchart, #2
B-6
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
SYMPTOM
PROBE HEATER START TO HEAT UP AND
THEN LOOSES TEMPERATURE. (MODEL
TC200 ONLY)
B
CHECK PARAMETER 35 ON TC200. IF THE
NUMBER IS NEGATIVE THEN SOMEWHERE
THE THERMOCOUPLE WIRES ARE REVERSED.
35730005
Figure B-6. HPS Troubleshooting Flowchart, #3
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
B-7
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
SERVICE AND NORMAL MAINTENANCE
B-5
OVERVIEW
e. Remove old transformer. Place new transformer in position and reconnect harness
plug as noted in step d.
This section describes service and routine
maintenance of the HPS 3000 Heater Power
Supply Field Module. Replacement parts referred to are available from Rosemount. Refer to
Table B-2 of this manual for part numbers and
ordering information.
f.
Place gasket and retaining plate on transformer.
g. Tighten hex nut only enough to firmly hold
transformer in place.
h. Reinstall HPS cover.
Install all protective equipment covers
and safety ground leads after equipment repair or service. Failure to install covers and ground leads could
result in serious injury or death.
B-6
FUSE REPLACEMENT
The heater power supply mother board (12,
Figure B-7) contains four identical 5 amp fuses.
Refer to Table B-1 for replacement fuse specifications. To check or replace a fuse, simply unscrew the top of the fuseholder with a flat head
screwdriver and remove fuse. After checking or
replacing a fuse, reinstall fuseholder top.
B-7
MOTHER BOARD REPLACEMENT
Install all protective equipment covers
and safety ground leads after equipment repair or service. Failure to install covers and ground leads could
result in serious injury or death.
a. Turn off power to system.
b. Loosen captive screws retaining HPS cover.
Remove cover.
TRANSFORMER REPLACEMENT
Install all protective equipment covers
and safety ground leads after equipment repair or service. Failure to install covers and ground leads could
result in serious injury or death.
a. Turn off power to system.
B-8
B-8
c. Remove hex nut (25, Figure B-7) from top of
transformer assembly. Remove retaining
plate (24) and gasket (22).
d. Disconnect transformer harness plug from
mother board.
e. Remove screws on either side of terminal
strip covers (2). Remove terminal strip covers (4 and 8).
b. Loosen captive screws retaining HPS cover.
Remove cover.
f.
c. Remove hex nut (25, Figure B-7) from top of
transformer assembly. Remove retaining
plate (24) and gasket (22).
g. Unscrew stand offs on either side of the
daughter board. Remove daughter board
(7).
d. Disconnect transformer harness plug from
mother board.
h. Unscrew four stand offs that supported the
daughter board.
Appendices
Unplug ribbon cable from the receptacle on
the daughter board (7).
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
i.
j.
Making a note of the location and color of
each wire, disconnect wires from terminal
strip on mother board.
Remove four screws (9) holding mother
board to stand offs (10) on subplate (14).
k. Remove mother board (12).
l.
Position new mother board on stand offs
and reinstall screws removed in step j.
m. Reconnect wires to terminal strip in positions noted in step i.
n. Reinstall four stand offs removed in step h.
Position daughter board on stand offs and
reinstall stand offs removed in step g.
o. Plug ribbon cable back into receptacle on
daughter board. Reinstall terminal covers.
p. Reinstall transformer, tightening hex nut
only enough to hold transformer firmly in
position. Reconnect transformer harness
plug to mother board.
a. Turn off power to system.
b. Loosen captive screws retaining HPS cover.
Remove cover.
c. Remove screws on either side of terminal
strip covers (2, Figure B-7). Remove terminal strip covers (4 and 8).
d. Making a note of the location and color of
each wire, disconnect wires from the terminal strip on the daughter board (7).
e. Unplug ribbon cable from receptacle on
daughter board.
f.
g. Position new daughter board on four stand
offs on mother board. Reinstall the stand
offs removed in step f.
h. Plug ribbon cable into receptacle on
daughter board.
i.
Reconnect wires to terminal strip in positions noted in step d. Reinstall terminal
covers.
j.
Reinstall HPS cover.
q. Reinstall HPS cover.
B-9
Unscrew two stand offs from daughter
board. Remove daughter board (7).
DAUGHTER BOARD REPLACEMENT
When turning power off at the HPS,
also turn off the respective probe at
associated electronics. When service
on the HPS is completed, restore
power at the HPS and the associated
electronics.
Rosemount Analytical Inc.
A Division of Emerson Process Management
Appendices
B-9
B
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
NOTE: NOT ALL PARTS SHOWN ARE AVAILABLE
FOR PURCHASE SEPARATELY. FOR LIST OF
AVAILABLE PARTS SEE TABLE B-2.
35730006
Figure B-7. Heater Power Supply, Exploded View
B-10
Appendices
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Manual
Appendix B Rev. 2.2
January 1997
World Class 3000
LEGEND FOR FIGURE B-7
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Enclosure Cover
Screw
Lockwasher
Terminal Cover
Stand Off
Lockwasher
Daughter Board
Terminal Cover
Screw
Stand Off
Hex Nut
Mother Board
Fuse
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
Subplate
Enclosure Box
Lockwasher
Stand Off
Screw
Lockwasher
Mounting Plate
Screw
Gasket
Transformer
Retaining Plate
Hex Nut
B
REPLACEMENT PARTS
Table B-2. Replacement Parts for Heater Power Supply
FIGURE and INDEX NO.
PART NUMBER
Figure B-1
Figure B-1
Figure B-1
Figure B-1
Figure B-1
Figure B-1
Figure B-7, 13
3D39129G01
3D39129G02
3D39129G03
1U05667G01
1U05667G02
1U05667G03
1L01293H02
Figure B-7, 12
Figure B-7, 7
Figure B-7, 23
Figure B-7, 23
3D39080G02
3D39078G01
1M02961G01
1M02961G02
Rosemount Analytical Inc.
A Division of Emerson Process Management
DESCRIPTION
Non-Hazardous HPS (120 Vac)
Non-Hazardous HPS (100 Vac)
Non-Hazardous HPS (220, 240 Vac)
Explosion-Proof HPS (120 Vac)
Explosion-Proof HPS (100 Vac)
Explosion-Proof HPS (220, 240 Vac)
Fuse, 5A @ 250 Vac, anti-surge, case
size; 5 x 20 mm, type T to IEC127,
Schurter
Mother Board
Daughter Board
Transformer (120, 220, 240 Vac)
Transformer (100 Vac)
Appendices
B-11
Instruction Manual
Appendix B Rev. 2.2
January 1997
B-12
Appendices
World Class 3000
Rosemount Analytical Inc.
A Division of Emerson Process Management
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
World Class 3000
SECTION 7
INDEX
This index is an alphabetized listing of parts, terms, and procedures having to do with the Hazardous Area Oxygen/Combustibles Transmitter. Every item listed in this index refers to a location
in the manual by one or more page numbers.
A
Abrasive Shield, 2-1
Absolute Temperature, 1-2
Adapter Plate, 2-1
Ambient Temperature, 2-9
Arithmetic Constant, 1-2
Model TC200 VERITRIM Electronics Package, 3-3
Models 218 Electronics Package, 3-1
Models 225 Electronics Package, 3-1
Mother Board, 2-10
Mounting Adaptor Plate, 1-2
N
NEMA 4X Enclosure, 2-9
Nernst Equation, 1-2
C
Cell Constant, 1-2
Ceramic Filter, 2-1
Check Valve, 1-3
O
Orsat Apparatus, 1-2
Oxygen Analyzer, 1-1
Oxygen Ions, 1-2
D
Dust Seal Packings, 2-6
P
Probe Heater Set Point, 3-1, 3-2, 3-3
E
Electrochemical Cell, 1-2
Electronic Packages, 1-1
EPROM, 3-2
Explosion-Proof Enclosure, 1-2
R
Reference Gas, 1-3
S
F
7
Sampling System, 1-1
Sensing Point, 2-1
Sensor Cell, 1-3
Solenoid Valve, 1-3
Fuses, 2-10, 2-11
G
Gas Stratification, 2-1
T
H
Transformer, 1-2
Heater Power Supply, 1-1
Hub Grooves, 2-6
V
Vee Deflector, 2-6
I
In Situ, 1-2
Instrument Air, 1-3
W
M
Z
Model 132 Digital Electronics Package, 3-4
Model 218A Digital Electronics Package, 3-2
Zirconia Disc, 1-2
Rosemount Analytical Inc.
Water Vapor, 1-2
A Division of Emerson Process Management
Index
7-1
Instruction Bulletin
106-300NE Rev. 3.4
May 2000
7-2
Index
World Class 3000
Rosemount Analytical Inc.
A Division of Emerson Process Management
WARRANTY
Goods and part(s) (excluding consumables) manufactured by Seller are warranted to be free from
defects in workmanship and material under normal use and service for a period of twelve (12)
months from the date of shipment by Seller. Consumables, glass electrodes, membranes, liquid
junctions, electrolyte, o-rings, etc., are warranted to be free from defects in workmanship and
material under normal use and service for a period of ninety (90) days from date of shipment by
Seller. Goods, part(s) and consumables proven by Seller to be defective in workmanship and/or
material shall be replaced or repaired, free of charge, F.O.B. Seller's factory provided that the
goods, part(s) or consumables are returned to Seller's designated factory, transportation charges
prepaid, within the twelve (12) month period of warranty in the case of goods and part(s), and in
the case of consumables, within the ninety (90) day period of warranty. This warranty shall be in
effect for replacement or repaired goods, part(s) and the remaining portion of the ninety (90) day
warranty in the case of consumables. A defect in goods, part(s) and consumables of the commercial unit shall not operate to condemn such commercial unit when such goods, part(s) and
consumables are capable of being renewed, repaired or replaced.
The Seller shall not be liable to the Buyer, or to any other person, for the loss or damage directly
or indirectly, arising from the use of the equipment or goods, from breach of any warranty, or from
any other cause. All other warranties, expressed or implied are hereby excluded.
IN CONSIDERATION OF THE HEREIN STATED PURCHASE PRICE OF THE GOODS,
SELLER GRANTS ONLY THE ABOVE STATED EXPRESS WARRANTY. NO OTHER WARRANTIES ARE GRANTED INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED
WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Limitations of Remedy. SELLER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE. THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT UNDER THE STANDARD
WARRANTY CLAUSE. IN NO CASE, REGARDLESS OF THE FORM OF THE CAUSE OF ACTION, SHALL SELLER'S LIABILITY EXCEED THE PRICE TO BUYER OF THE SPECIFIC
GOODS MANUFACTURED BY SELLER GIVING RISE TO THE CAUSE OF ACTION. BUYER
AGREES THAT IN NO EVENT SHALL SELLER'S LIABILITY EXTEND TO INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES. CONSEQUENTIAL DAMAGES SHALL INCLUDE, BUT
ARE NOT LIMITED TO, LOSS OF ANTICIPATED PROFITS, LOSS OF USE, LOSS OF REVENUE, COST OF CAPITAL AND DAMAGE OR LOSS OF OTHER PROPERTY OR EQUIPMENT.
IN NO EVENT SHALL SELLER BE OBLIGATED TO INDEMNIFY BUYER IN ANY MANNER
NOR SHALL SELLER BE LIABLE FOR PROPERTY DAMAGE AND/OR THIRD PARTY CLAIMS
COVERED BY UMBRELLA INSURANCE AND/OR INDEMNITY COVERAGE PROVIDED TO
BUYER, ITS ASSIGNS, AND EACH SUCCESSOR INTEREST TO THE GOODS PROVIDED
HEREUNDER.
Force Majeure. Seller shall not be liable for failure to perform due to labor strikes or acts beyond
Seller's direct control.
2461
3333/5-00
Instruction Manual
106-300NE Rev. 3.4
May 2000
World Class 3000
World Class 3000 Probe
Part No. ________________
Serial No. ________________
Order No. ________________
HPS 3000
Part No. ________________
Serial No. ________________
Order No. ________________
Emerson Process Management
Rosemount Analytical Inc.
Process Analytic Division
1201 N. Main St.
Orrville, OH 44667-0901
T (330) 682-9010
F (330) 684-4434
E gas.csc@emersonprocess.com
Fisher-Rosemount GmbH & Co.
Industriestrasse 1
63594 Hasselroth
Germany
T 49-6055-884 0
F 49-6055-884209
ASIA - PACIFIC
Fisher-Rosemount
Singapore Private Ltd.
1 Pandan Crescent
Singapore 128461
Republic of Singapore
T 65-777-8211
F 65-777-0947
EUROPE, MIDDLE EAST, AFRICA
Fisher-Rosemount Ltd.
Heath Place
Bognor Regis
West Sussex PO22 9SH
England
T 44-1243-863121
F 44-1243-845354
http://www.processanalytic.com
© Rosemount Analytical Inc. 2001
LATIN AMERICA
Fisher - Rosemount
Av. das Americas
3333 sala 1004
Rio de Janeiro, RJ
Brazil 22631-003
T 55-21-2431-1882