Specifications | Emerson 4015 Power Supply User Manual

Instruction Sheet
PN 51A-5081P-FF-FI/rev.B
October 2007
Model 5081-P-FF/FI
®
FOUNDATION Fieldbus Two-Wire pH/ORP
Transmitter
For additional information, please refer to the Instruction Manuals CD shipped with this
product, or visit our website at www.emersonprocess.com/raihome/liquid/.
ESSENTIAL INSTRUCTIONS
READ THIS PAGE BEFORE PROCEEDING!
Your purchase from Rosemount Analytical, Inc. has resulted in one of the finest instruments available for your
particular application. These instruments have been designed, and tested to meet many national and international standards. Experience indicates that its performance is directly related to the quality of the installation
and knowledge of the user in operating and maintaining the instrument. To ensure their continued operation to
the design specifications, personnel should read this manual thoroughly before proceeding with installation,
commissioning, operation, and maintenance of this instrument. If this equipment is used in a manner not specified by the manufacturer, the protection provided by it against hazards may be impaired.
• Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life;
personal injury; property damage; damage to this instrument; and warranty invalidation.
• Ensure that you have received the correct model and options from your purchase order. Verify that this manual covers your model and options. If not, call 1-800-854-8257 or 949-757-8500 to request correct manual.
• For clarification of instructions, contact your Rosemount representative.
• Follow all warnings, cautions, and instructions marked on and supplied with the product.
• Use only qualified personnel to install, operate, update, program and maintain the product.
• Educate your personnel in the proper installation, operation, and maintenance of the product.
• Install equipment as specified in the Installation section of this manual. Follow appropriate local and national
codes. Only connect the product to electrical and pressure sources specified in this manual.
• Use only factory documented components for repair. Tampering or unauthorized substitution of parts and
procedures can affect the performance and cause unsafe operation of your process.
• All equipment doors must be closed and protective covers must be in place unless qualified personnel are
performing maintenance.
• If this equipment is used in a manner not specified by the manufacturer, the protection provided by it against
hazards may be impaired.
MODEL 5081-P-FF/FI
SPECIFICATIONS
SPECIFICATIONS -GENERAL
Case: Cast aluminum containing less than 6% magnesium.
NEMA 4X (IP65), NEMA 7 (explosion-proof)
Epoxy-polyester paint, Neoprene O-ring seals
Dimensions: 6.3 in. x 6.9 in. x 6.4 in. (160 mm x 175 mm x 161
mm); diameter 6.1 in (155 mm)
Conduit Openings: 3/4 in. FNPT
Reference Impedance: Transmitter accepts high impedance
(i.e. glass) reference electrodes as well as low impedance
(i.e. silver-silver chloride) reference electrodes.
Response Time: Display reaches 95% of final reading within 10
seconds.
Temperature Sensors: The following RTDs can be used with
the Model 5081-P pH/ORP transmitter:
3 and 4 wire Pt 100 RTDs
3 and 4 wire Pt 1000 RTDs
Non-Incendive:
Class I, Div. 2, Groups A-D
Dust Ignition Proof
Class II & III, Div. 1, Groups E-G
NEMA 4X Enclosure
Class I, Div. 2, Groups A-D
Suitable for Class II, Div. 2, Groups E-G
T4
Tamb = 70°C
Explosion-Proof:
Class I, Div. 1, Groups B-D
Class II, Div. 1, Groups E-G
Class III, Div. 1
Class I, Groups B-D
Class II, Groups E-G
Class III
Tamb = 65°C max
Transmitter can also be used with two-wire RTDs.
Temperature Range: 5°F to 248°F (-15°C to 130°C)
SPECIFICATIONS - pH
Local Display: Two line LCD; first line shows process variable
(pH or ORP), second line shows temperature and output signal. When triggered, fault and warning messages alternate
with temperature and output readings.
pH Input Range: 0 to 14 pH
Accuracy at 25°C: ±0.01 pH
Process variable: 7 segment LCD, 0.8 in. (20 mm) high
Repeatability at 25°C: ±0.01 pH
Temperature/output: 7 segment LCD, 0.3 in. (7 mm) high
Resolution: 0.01 pH and 0.1°C or °F
Display board can be rotated 90 degrees clockwise or counterclockwise.
Stability at 25°C: 0.25% per year
Diagnostics: The internal diagnostics can detect:
Calibration Error
Low Temperature Error
High Temperature Error
Sensor Failure
Line Failure
CPU Failure
ROM Failure
Input Warning
Glass Failure
Glass Warning
Reference Failure
Reference Warning
Once one of the above is diagnosed, the LCD will display a
message describing the failure/default detected.
During calibration and programming, messages and prompts
appear in the temperature/output area.
Power Supply and Load Requirements: A power supply volt-
age of 9-32 Vdc at 22 mA is required.
Security: User selected security code prevents accidental
changes to program settings.
Ambient Temperature: -4 to 149°F (-20 to 65°C)
Relative Humidity: 0 to 95% (with covers sealed)
Storage Temperature: -22 to 176°F (-30 to 80°C)
EN-61326
Sira MC070112/00
Hazardous Area Classification:
Intrinsic Safety:
Class I, II, III, Div. 1
Groups A-G
T4
Tamb = 70°C
Exia Entity
Class I, Groups A-D
Class II, Groups E-G
Class III
T4
Tamb = 70°C
ATEX
0600 II 1 G
Baseefa02ATEX1284
EEx ia IIC T4
Tamb = -20°C to +65°C
Temperature Compensation: Automatic or manual between 5°F
to 248°F (-15°C to 130°C)
Solution Temperature Compensation: Transmitter will convert
pH measured at any temperature to the pH at 25°C.
Temperature coefficient is programmable between -0.044
pH/°C and 0.028 pH/°C
EMI/RFI: Meets the requirements of
2
Temperature Input Range: 5°F to 248°F (-15°C to 130°C)
Calibration: Automatic two-point and manual two-point buffer
calibration. For automatic calibration, the transmitter recognizes NIST, DIN 19266 and 19267, JIS 8802, BSM, Merck,
and Ingold buffers.
SPECIFICATIONS - ORP
ORP Input Range: -1400 to 1400 mV
Temperature Input Range: 5°F to 248°F (-15°C to 130°C)
Output Scale Expansion: Continuously expandable between 1400 and 1400 mV
Accuracy at 25°C: ±1 mV
Repeatability at 25°C: ±1 mV
Resolution: 1 mV and 0.1°C or °F
Stability at 25°C: 0.25% per year
MODEL 5081-P-FF/FI
WIRING
SENSOR WIRING AND SET-UP
WIRING THROUGH A JUNCTION BOX
Wire sensor per Figure 1. Refer to the sensor instruction
manual for more details.
If your sensor has an integral preamplifier or you are using
a remote preamplifier, you will need to change the preamplifier location in the program menu. Please see Figure 14.
Select “trAnS” for integral preamplifier or “SnSr” for J-box
or sensor preamplifier.
Sensors with integral preamplifiers can be wired to the analyzer through a remote junction box (PN 23550-00). Wire
the extension cable and sensor cable point-to-point. Refer
to the sensor instruction manual for more details.
WIRING THROUGH A JUNCTION BOX WITH
REMOTE PREAMPLIFIER
POWER WIRING
For general purpose areas, wire power as shown in
Figure 1. For hazardous areas, please see hazardous
area installation drawings.
Wire sensor as shown in Figure 5. Refer to the sensor
instruction manual for more details.
(9 - 32 VDC)
NOTE: REF wire covered with
sleeving. To prevent
depletion of KCL if
other wires touched,
remove sleeving
before wiring to TB-7.
FIGURE 1. Model 5081-P-FF/FI Wiring Details
3
MODEL 5081-P-FF/FI
WIRING
FIGURE 2. Exploded View of Model 5081-P-FF/FI
DWG. NO.
45081P30
REV.
A
FIGURE 3. Wiring Diagram — Sensor with Preamplifier
4
MODEL 5081-P-FF/FI
DWG. NO.
45081P28
WIRING
REV.
A
FIGURE 4. Wiring diagram — sensor Model 381+ with preamplifier
WIRING THROUGH A JUNCTION BOX WITH REMOTE PREAMPLIFIER
Wire sensor as shown in Figure 5. Refer to the sensor instruction manual for more details.
DWG. NO.
45081P29
FIGURE 5. Wiring Through a Junction Box with Remote Preamplifier
REV.
A
5
MODEL 5081-P-FF/FI
INSTALLATION
INSTALLATION
UNPACKING AND INSPECTION
INSTALLATION
Inspect the shipping container. If it is damaged, contact the
shipper immediately for instructions. Save the box. If there
is no apparent damage, unpack the container. Be sure all
items shown on the packing list are present. If items are
missing, notify Rosemount Analytical immediately.
See Figure 6.
1. Although the analyzer is suitable for outdoor use, do not
install it in direct sunlight or in areas of extreme temperatures.
2. Install the analyzer in an area where vibrations and electromagnetic and radio frequency interference are minimized or absent.
ROTATING THE DISPLAY
The 5081-P-FF/FI display can be rotated 90° left or right.
Disengage the cover lock and remove the front cover.
Remove the three screws holding the PCB stack and gently lift the display board. Do not disengage the ribbon cable
between the display board and the CPU board. Rotate the
display. The black infrared sensor will be at the top of the
display.
3. Keep the analyzer and sensor wiring at least one foot
from high voltage conductors. Be sure there is easy
access to the analyzer.
4. The conduit connections on the sides of the 5081-P
housing should be sealed to prevent moisture from
entering the enclosure.
5. The transmitter must not be mounted with both conduit
openings at the top.
MILLIMETER
INCH
FIGURE 6. Mounting Model 5081-P-FF/FI
6
7
FIGURE 8. FM Intrinsically Safe Installation Label
MODEL 5081-P-FF/FI
HAZARDOUS AREA INSTALLATION
FIGURE 7. FMRC Explosion-Proof Installation
HAZARDOUS AREA INSTALLATION
8
9
FIGURE 9. FM Intrinsically Safe Installation (1 of 2)
10
FIGURE 9. FM Intrinsically Safe Installation (2 of 2)
11
FIGURE 10. CSA Intrinsically Safe Installation Label
12
FIGURE 11. CSA Intrinsically Safe Installation (1 of 2)
13
FIGURE 11. CSA Intrinsically Safe Installation (2 of 2)
14
FIGURE 12. ATEX Intrinsically Safe Installation Label
15
FIGURE 13. ATEX Intrinsically Safe Installation (1 of 2)
16
FIGURE 14. ATEX Intrinsically Safe Installation (2 of 2)
APPROVED
NO CHANGE WITHOUT FM APPROVAL.
MATERIAL: AISI 300 SERIES STAINLESS
STEEL .015+/-.005 THICK. MATERIAL TO
BE ANNEALED & PASSIVATED. MAXIMUM
HARDNESS BRINELL 190.
2.
1
NOTES: UNLESS OTHERWISE SPECIFIED
ARTWORK IS SHEET 2 OF 2.
1.30 ±.02
2X.650 ±.015
3.
.125
9241503-01/A
EXPLOSION PROOF
CLASS I, DIV.1, GRPS. B,C & D
CLASS II, DIV. 1, GRPS. E,F & G
CLASS III, DIV. 1
PER DWG. 1400296
INTRINSICALLY SAFE FOR
CLASS I, II & III, DIV. 1,
GRPS. A,B,C,D,E,F & G
HAZARDOUS AREA WHEN
CONNECTED PER DWG. 1400287
Tamb= 70°C
T4
NON-INCENDIVE
CLASS I, DIV. 2, GRPS. A,B,C & D
DUST IGNITION PROOF
CLASS II AND III, DIV. 1,
GRPS. E, F & G
WARNING: COMPONENT SUBSTITUTION
MAY IMPAIR INTRINSIC SAFETY
OR SUITABILITY FOR DIV. 2.
NEMA 4X ENCLOSURE.
FINISH:SILKSCREEN BLACK EPOXY PAINT (BAKED).
.140
R
8933
5-6-04
.XXX
FINISH
ANGLES
TOLERANCES
+ 1/2
-
4
1
DIMENSIONS ARE IN INCHES
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+ .030
+- .010
UNLESS OTHERWISE SPECIFIED
.XX
LTR
PART NO
A
REV
THIS DWG CREATED IN
SOLID EDGE
PROJECT
ENGR APVD J. FLOCK
J. FLOCK
B. JOHNSON
APPROVALS
CHECKED
DRAWN
ITEM
2.56 ±.02
ECO NO
RELEASE DATE
2.180
.120 ±.015
MATERIAL
Ø .125
ROSEMOUNT ANALYTICAL
MODEL
FM
5081-P-FI-67
4
2X FULL R
4X R .25
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
ECO
DATE
5/6/04
5/6/04
5/3/04
SCALE 2:1
B
SIZE
DWG NO
Uniloc
BY
DATE
REV
REV
REV
REV
REV
REV
A
9241503-01
SHEET 1 OF
CHK
2
A
REV
QTY
Rosemount Analytical,
Uniloc Division
2400 Barranca Pkwy
Irvine, CA 92606
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
FM
THIS DOCUMENT IS
CERTIFIED BY
LABEL, I.S. FM
5081-P-FI
DESCRIPTION
BILL OF MATERIAL
TITLE
REVISIONS
DESCRIPTION
B 9241503-01
17
pH SENSOR
OPTIONAL PREAMP/J-BOX
RIGID METAL CONDUIT
AND APPROVED SEALS
8
NOTES: UNLESS OTHERWISE SPECIFIED
1. INSTALLATION MUST CONFORM TO THE NEC.
2. SEAL REQUIRED AT EACH CONDUIT ENTRANCE.
7
3 USE ONLY APPROVED CONDUIT SEALS AND FITTINGS.
3
6
2
RESERVED
WIRING LABEL
8
SOL
GND
9
pH/ORP
10
pH/O
GUARD
R
IN P
E RAT E D
US T B
F OR
M
G
70
I N
R
^C
WI
7
N
REF-I
7
6
5
CLASS I, DIV 1, GPS B-D
CLASS II, DIV 1, GPS E-G
CLASS III, DIV 1
70 v C MAX
HAZARDOUS AREA
5081-P-FI-67
3
1
-5V 1
4
4
RELEASE DATE
5-6-04
RIGID METAL CONDUIT
AND APPROVED SEALS
1
HT/FF6
(+)
A
B
C
SAFE AREA
6
FRE UARD
G
5
5
9
D
RECOMMENDED SENSORS:
320B
320HP
328A
330B
370
371
381+
385+
389
396
396P
396R
396PVP
396RVP
396VP
397
398
398R
398RVP
398VP
399
399VP
6
8
7
11
8
12
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
10
4
RTD
SEN
SE
3
RTD
RTN
1
RVED
RESE
RT 5
IN D
/B
- 00
518
41
92
PN
4
3
2
15
HT/FF
(-)
1
14
CATHODE/
RESERVED
14
18
13
12 V
+5
13 E/
D
ANO VED
RESER
16 15
ECO NO.
8933
REV
A
FINISH
ANGLES
TOLERANCES
+
-
3
DIMENSIONS ARE IN INCHES
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+ .030
+
- .010
MATERIAL
.XX
.XXX
UNLESS OTHERWISE SPECIFIED
3
ECO
PART NO.
THIS DWG CREATED IN
SOLID EDGE
2
5/6/04
PROJECT
ENGR APVD
J. FLOCK
5/6/04
5/3/04
DATE
2
CHECKED J. FLOCK
B. JOHNSON
APPROVALS
DRAWN
ITEM
POWER SUPPLY
17.5 VDC MAX
SAFE AREA
LTR
DESCRIPTION
Emerson
BILL OF MATERIAL
DATE
D
SCALE
NONE
DWG NO.
TYPE
1400296
1
SHEET 1 OF
1
Emerson Process Management,
Rosemount Analytical Division
2400 Barranca Pkwy
Irvine, CA 92606
EXP PROOF 5081-P-FI
SIZE
REV
REV
REV
REV
REV
REV
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
FM
THIS DOCUMENT IS
CERTIFIED BY
BY
1
SCHEM, SYSTEM FMRC
TITLE
DESCRIPTION
REVISION
06-01
A
REV
QTY
A
CHK
A
B
C
D 1400296
A
B
C
D
REV
REV
REV
REV
REV
REV
B
NOTES: UNLESS OTHERWISE SPECIFIED
8
+PH
SENSOR
PREAMP
(NOTE 2)
7
WARNING-
WARNING-
5
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
6
5
TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOSPHERES,
DISCONNECT POWER BEFORE SERVICING.
SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY OR
SUITABILITY FOR DIVISION 2.
TB14
5
7
10
FM APPROVED PREAMP
THAT MEETS REQUIREMENTS
OF NOTE 1
PREAMP
(NOTE 2)
RECOMMENDED CABLE
4 WIRES SHIELDED
22 AWG. SEE NOTE 1
PH
SENSOR
WITH
TC
+PH
SENSOR
RECOMMENDED CABLE
PN 9200273 (UNPREPPED)
PN 23646-01 PREPPED
10 COND, 2 SHIELDS 24 AWG
SEE NOTE 1
6
FISCO
FM INTRINSIC SAFETY INSTALLATION
FM APPROVED PREAMP
THAT MEETS REQUIREMENTS
OF NOTE 1
+PH
SENSOR
INFRARED RED
REMOTE CONTROL UNIT
(RMT PN 23572-00)
FOR USE IN
CLASS I AREA ONLY
NOTES ON SHEET 2 OF 2
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
FM
THIS DOCUMENT IS
CERTIFIED BY
7
6
3
2
8
11
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
5
5
4
3
2
1
4
3
2
1
4
3
2
1
6
6
6
7
7
7
7
5
5
8
8
8
8
12
1
4
9
9
9
9
13
14
16 15
13
14
10
10
10
10
11
11
11
12
12
12
16 15
13
14
16 15
13
14
16 15
3
4
RELEASE DATE
5-6-04
ECO NO.
8933
IS CLASS I, II, III,
DIVISION 1,
GROUPS A, B, C, D, E, F, G;
NI CLASS I,
DIVISION 2,
GROUPS A,B,C,D;
SUITABLE CLASS II,
DIVISION 2,
GROUPS F & G;
SUITABLE CLASS III,
DIVISION 2
REV
B
FINISH
ANGLES
TOLERANCES
+ 1/2
DIMENSIONS ARE IN INCHES
3
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+ .030
+ .010
-
MATERIAL
.XX
.XXX
UNLESS OTHERWISE SPECIFIED
ANY FM APPROVED
TERMINATOR
ANY FM APPROVED
INTRINSICALLY SAFE
APPARATUS
ANY FM APPROVED
TERMINATOR
ANY FM APPROVED
INTRINSICALLY SAFE
APPARATUS
ANY FM APPROVED
TERMINATOR
ANY FM APPROVED
INTRINSICALLY SAFE
APPARATUS
ANY FM APPROVED
TERMINATOR
ANY FM APPROVED
INTRINSICALLY SAFE
APPARATUS
HAZARDOUS (CLASSIFIED)LOCATIONS
4
PART NO.
J. FLOCK
ANY FM APPROVED
TERMINATOR
ANY FM APPROVED
TERMINATOR
2
5/6/04
5/6/04
5/3/04
DATE
DATE
DESCRIPTION
Uniloc
BILL OF MATERIAL
D
SIZE
SCALE NONE
Rosemount Analytical,
Uniloc Division
2400 Barranca Pkwy
Irvine, CA 92606
1
SHEET 1 OF
2
10-96
B
REV
QTY
ANY FM APPROVED
ASSOCIATED
APPARATUS
ANY FM APPROVED
ASSOCIATED
APPARATUS
ANY FM APPROVED
ASSOCIATED
APPARATUS
1400287
TYPE
CHK
ANY FM APPROVED
ASSOCIATED
APPARATUS
SCHEMATIC, INSTALLATION
5081-P-FI XMTR
FM APPROVALS
TITLE
ANY FM APPROVED
TERMINATOR
THIS DWG CREATED IN
SOLID EDGE
PROJECT
ENGR APVD
CHECKED J. FLOCK
BY
1
NON-HAZARDOUS LOCATIONS
DESCRIPTION
REVISION
ANY FM APPROVED
TERMINATOR
B. JOHNSON
APPROVALS
ECO
DRAWN
ITEM
LTR
2
A
B
C
D 1400287
19
A
B
C
D
20
8
7
6
8
NOTES: UNLESS OTHERWISE SPECIFIED
7
1. THE MODEL 5081-P-FI TRANSMITTER INCLUDES INTEGRAL PREAMPLIFIER
CIRCUITRY. AN EXTERNAL PREAMPLIFIER MAY BE ALSO USED.
THE OUTPUT PARAMETERS SPECIFIED IN TABLE II ARE VALID FOR EITHER
PREAMPLIFIER.
THE CAPACITANCE AND INDUCTANCE OF THE LOAD CONNECTED TO THE
SENSOR TERMINALS MUST NOT EXCEED THE VALUES SPECIFIED IN TABLE I
WHERE Ca
Ci (SENSOR) + Ccable;
La
Li (SENSOR) + Lcable.
2. PREAMPLIFIER TYPE 23546-00, 23538-00 OR 23561-00 MAY BE UTILIZED INSTEAD
OF THE MODEL 5081-P-FI TRANSMITTER INTEGRAL PREAMPLIFIER
CIRCUIRTY. A WEATHER RESISTANT ENCLOSURE MUST HOUSE THE TYPE
23546-00 REMOTE PREAMPLIFIER.
3. INSTALLATION SHOULD BE IN ACCORDANCE WITH ANSI/ISA RP12.06
"INSTALLATION OF INTRINSICALLY SAFE SYSTEMS FOR HAZARDOUS
(CLASSIFIED) LOCATIONS" (EXCEPT CHAPTER 5 FOR FISCO INSTALLATIONS) AND
THE NATIONAL ELECTRICAL CODE (ANSI/NFPA 70) SECTIONS 504 AND 505.
6
4. SENSORS WITHOUT PREAMPS SHALL MEET THE REQUIREMENTS OF SIMPLE APPARATUS AS
DEFINED IN ANSI/ISA RP12.6 AND THE NEC, ANSI/NFPA 70.
THEY CAN NOT GENERATE NOR STORE MORE THAN 1.5V, 0.1A OR A PASSIVE COMPONENT
THAT DOES NOT DISSIPATE MORE THAN 1.3W. SEE TABLES I AND II.
5. DUST-TIGHT CONDUIT SEAL MUST BE USED WHEN INSTALLED IN CLASS II AND
CLASS III ENVIRONMENTS.
6. RESISTANCE BETWEEN INTRINSICALLY SAFE GROUND AND EARTH GROUND MUST BE
LESS THAN 1.0 Ohm.
7. THE ENTITY CONCEPT ALLOWS INTERCONNECTION OF INTRINSICALLY SAFE APPARATUS
WITH ASSOCIATED APPARATUS WHEN THE FOLLOWING IS TRUE:
FIELD DEVICE INPUT
ASSOCIATED APPARATUS OUTPUT
Vmax OR Ui
Voc, Vt OR Uo;
Imax OR Ii
Isc, It OR Io;
Pmax OR Pi
Po;
3Ci+ 3Ccable;
Ca, Ct OR Co
3Li+ 3Lcable.
La, Lt OR Lo; OR Lc/Rc
(La/Ra OR Lo/Ro) AND Li/Ri
8. ASSOCIATED APPARATUS MANUFACTURER'S INSTALLATION DRAWING MUST BE FOLLOWED
WHEN INSTALLING THIS EQUIPMENT.
(La/Ra OR Lo/Ro)
9. CONTROL EQUIPMENT CONNECTED TO ASSOCIATED APPARATUS MUST NOT USE OR GENERATE
MORE THAN 250 Vrms OR Vdc.
10. THE CONFIGURATION OF ASSOCIATED APPARATUS MUST BE FACTORY MUTUAL RESEARCH APPROVED
UNDER THE ASSOCIATED CONCEPT.
11. NO REVISION TO DRAWING WITHOUT PRIOR FACTORY MUTUAL RESEARCH APPROVAL.
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
5
5
TABLE I
17.5
17.5
IIB/
C,D,E,F,G
IIC/
A,B,C,D,E,F,G
5081-P-FI
5081-P-FI
4
Vmax (Vdc)
GROUPS
MODEL NO.
360
380
Imax (mA)
3
2.52
5.32
Pmax (W)
5
5
Ci (nF)
10
10
Li (uH)
Pt
25
21.69
D
TABLE III
147 mW
It
5081-P-FI FISCO PARAMETERS
SUPPLY / SIGNAL TERMINALS TB 1-15, 16
13.02 Vdc
105.64 mA
Vt
3.1
12.3
5.99
MODEL 5081-P-FI
TB1-1 THRU 12
TABLE II
OUTPUT
PARAMETERS
0.96
La
(mH)
C
Ca
(uF)
OUTPUT PARAMETERS
3
A, B
GAS
GROUPS
4
2
2
D
DWG NO.
SCALE: NONE
SIZE
TYPE
1
1400287
1
SHEET 2 OF 2
08-94
B
REV
A
B
C
D 1400287
R
SA
R
LR34186
ENCLOSURE 4
NO CHANGE WITHOUT CSA APPROVAL.
MATERIAL: AISI 300 SERIES STAINLESS
STEEL .015+/-.005 THICK. MATERIAL TO
BE ANNEALED & PASSIVATED. MAXIMUM
HARDNESS BRINELL 190.
2.
1
NOTES: UNLESS OTHERWISE SPECIFIED
.650 ±.015
1.30 ±.02
ARTWORK IS SHEET 2 OF 2.
.125
9241504-01/A
CLASS I, DIV. 2, GRPS A,B,C & D
SUITABLE FOR
CLASS II, DIV. 2, GRPS E, F & G
Tamb= 70°C
T4
WARNING-EXPLOSION HAZARD-DO NOT
DISCONNECT WHILE CIRCUIT IS LIVE
UNLESS AREA IS KNOWN TO BE NONHAZARDOUS.
WARNING-EXPLOSION HAZARD-SUBSTITUTION OF COMPONENTS MAY IMPAIR
SUITABILITY FOR CLASS I, DIV 2.
CLASS I, GRPS B,C & D
CLASS II, GRPS E, F & G
CLASS III
Tamb = 65°C MAX
Tamb ABOVE 60°C USE 75°C MINIMUM
RATED WIRING
SEAL REQUIRED TO BE INSTALLED
WITHIN 50 mm OF THE ENCLOSURE.
KEEP COVER TIGHT WHILE CIRCUITS
ARE LIVE.
Exia ENTITY
INTRINSICALLY SAFE FOR
CLASS I, GRPS A, B, C & D
CLASS II, GRPS E, F & G
CLASS III
T4 Tamb = 70°C
HAZARDOUS AREA WHEN CONNECTED
PER DWG. 1400288
WARNING: COMPONENT SUBSTITUTION
MAY IMPAIR INTRINSIC SAFETY.
MODEL
5081-P-FI-69
.XXX
.XX
FINISH
ANGLES
TOLERANCES
+ 1/2
-
4
1
DIMENSIONS ARE IN INCHES
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+ .030
+- .010
UNLESS OTHERWISE SPECIFIED
4
2.180 ±.005
A
8925
2.56 ±.02
REV
ECO NO
LTR
ECO
PART NO
THIS DWG CREATED IN
SOLID EDGE
PROJECT
ENGR APVD J. FLOCK
J. FLOCK
B. JOHNSON
APPROVALS
CHECKED
DRAWN
ITEM
DATE
5/6/04
5/6/04
5/3/04
DESCRIPTION
DATE
REV
REV
REV
REV
REV
REV
A
SHEET 1 OF
CHK
2
10-96
A
REV
QTY
Rosemount Analytical,
Uniloc Division
2400 Barranca Pkwy
Irvine, CA 92606
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
CSA
9241504-01
DWG NO
SCALE 2:1
B
SIZE
BY
THIS DOCUMENT IS
CERTIFIED BY
LABEL, I.S. CSA
5081-P-FI
Uniloc
TITLE
REVISIONS
DESCRIPTION
BILL OF MATERIAL
FINISH:SILKSCREEN BLACK EPOXY PAINT (BAKED).
RELEASE DATE
5-6-04
.120 ±.015
MATERIAL
Ø .125
ROSEMOUNT ANALYTICAL
3.
.140 ±.005
2X FULL R
4X R .25
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
B 9241504-01
21
A
B
C
D
REV
REV
REV
REV
REV
REV A
8
PREAMP
(NOTE 3)
7
6
WARNING-
WARNING-
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
5
12
6
5
HAZARDOUS AREA
4
ECO NO.
4
8925
5-6-04
RELEASE DATE
NI CLASS I, DIV 2
GRPS A-D
CLASS II, DIV 2
GRPS E-G
IS CLASS I, GRPS A-D
CLASS II, GRPS E-G
CLASS III
TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOSPHERES,
DISCONNECT POWER BEFORE SERVICING.
SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY OR
SUITABILITY FOR DIVISION 2.
TB14
5
7
10
CSA APPROVED PREAMP
THAT MEETS REQUIREMENTS
OF NOTE 2
PREAMP
(NOTE 3)
RECOMMENDED CABLE
4 WIRES SHIELDED
22 AWG. SEE NOTE 1
PH
SENSOR
WITH
TC
+PH
SENSOR
RECOMMENDED CABLE
PN 9200273 (UNPREPPED)
PN 23646-01 PREPPED
10 COND, 2 SHIELDS 24 AWG
SEE NOTE 1
CSA APPROVED PREAMP
THAT MEETS REQUIREMENTS
OF NOTE 2
+PH
SENSOR
INFRARED RED
REMOTE CONTROL UNIT
(RMT PN 23572-00)
FOR USE IN
CLASS I AREA ONLY
NOTES ON SHEET 2 OF 2
NOTES: UNLESS OTHERWISE SPECIFICED
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
CSA
THIS DOCUMENT IS
CERTIFIED BY
+PH
SENSOR
FISCO
CSA INTRINSIC SAFETY INSTALLATION
7
11
8
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
5
5
4
3
2
1
4
3
2
1
4
3
6
6
6
6
2
7
7
7
7
5
5
8
8
8
8
1
4
3
2
1
9
9
9
9
13
14
16 15
13
14
10
10
10
10
11
11
11
12
12
12
16 15
13
14
16 15
13
14
22
16 15
A
REV
FINISH
ANGLES
TOLERANCES
+
-
3
DIMENSIONS ARE IN INCHES
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+ .030
+ .010
-
MATERIAL
.XX
.XXX
UNLESS OTHERWISE SPECIFIED
3
REVISION
DESCRIPTION
2
5/6/04
THIS DWG CREATED IN
SOLID EDGE
J. FLOCK
PROJECT
ENGR APVD
5-3-04
5/6/04
B. JOHNSON
CHECKED J. FLOCK
DRAWN
APPROVALS
TITLE
SCALE
SIZE
D
NONE
DWG NO.
TYPE
1400288
1
SHEET 1 OF
SCHEMATIC, INSTALLATION
5081-P-FI XMTR CSA
Uniloc
BILL OF MATERIAL
DATE
Rosemount Analytical,
Uniloc Division
2400 Barranca Pkwy
Irvine, CA 92606
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
CSA APPROVED
ASSOCIATED APPARATUS
SUITABLE FOR FISCO
SEE NOTE 8 AND TABLE III
DESCRIPTION
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
CSA APPROVED
ASSOCIATED APPARATUS
SUITABLE FOR FISCO
SEE NOTE 8 AND TABLE III
PART NO.
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
ITEM
1
BY
CSA APPROVED
ASSOCIATED APPARATUS
SUITABLE FOR FISCO
SEE NOTE 8 AND TABLE III
DATE
UNCLASSIFIED AREA
2
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
ECO
CSA APPROVED
ASSOCIATED APPARATUS
SUITABLE FOR FISCO
SEE NOTE 8 AND TABLE III
LTR
2
A
REV
QTY
CHK
A
B
C
D 1400288
II 1 G
NO CHANGE WITHOUT BASEEFA APPROVAL.
MATERIAL: AISI 300 SERIES STAINLESS
STEEL .015+/-.005 THICK. MATERIAL TO
BE ANNEALED & PASSIVATED. MAXIMUM
1
NOTES: UNLESS OTHERWISE SPECIFIED
.650 ±.015
1.30 ±.02
2.
.125
9241502-01/A
SIGNAL INPUT
Uo = 13.1 V
Io = 173 mA
Po = 231 mW
Ci= 0.010 µF
Li= 0 µ H
FISCO SUPPLY
Ui = 17.5 VDC
Ii = 380 mA
Pi = 5.32 W
Ci= 0 µ F
Li= 0 µH
BAS02ATEX1284
EEx ia IIC T4
Tamb = -20°C TO +65°C
MODEL 5081-P-FI-73
1180
ARTWORK IS SHEET 2 OF 2.
HARDNESS BRINELL 190.
R
RELEASE DATE
5-6-04
.XXX
.XX
FINISH
ANGLES
TOLERANCES
+ 1/2
-
4
1
DIMENSIONS ARE IN INCHES
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+ .030
+- .010
A
8925
2.56 ±.02
REV
ECO NO
LTR
ECO
PART NO
J. FLOCK
THIS DWG CREATED IN
SOLID EDGE
PROJECT
ENGR APVD
J. FLOCK
B. JOHNSON
APPROVALS
CHECKED
DRAWN
ITEM
DATE
5/6/04
5/6/04
5/3/04
DESCRIPTION
DATE
REV
REV
REV
REV
REV
REV
A
SHEET 1 OF
CHK
2
A
REV
QTY
Rosemount Analytical,
Uniloc Division
2400 Barranca Pkwy
Irvine, CA 92606
Baseefa Certified Product
No modifications permitted
without the approval of
the Authorized Person
Related Drawing
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
Baseefa
9241502-01
DWG NO
SCALE 2:1
B
SIZE
BY
THIS DOCUMENT IS
CERTIFIED BY
LABEL, I.S. BAS/ATEX
5081-P-FI
Uniloc
TITLE
REVISIONS
DESCRIPTION
BILL OF MATERIAL
FINISH:SILKSCREEN BLACK EPOXY PAINT (BAKED).
UNLESS OTHERWISE SPECIFIED
4
2.180 ±.005
.120 ±.015
MATERIAL
Ø .125
ROSEMOUNT ANALYTICAL
3.
2X FULL R
.140 ±.005
4X R .25
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
B 9241502-01
23
A
B
C
D
8
NOTES: UNLESS OTHERWISE SPECIFIED
7
WARNING-
WARNING-
6
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
MODEL
5081-P-FI
XMTR
12
11
6
TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOSPHERES,
DISCONNECT POWER BEFORE SERVICING.
SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY.
TB14
5
7
10
ATEX APPROVED PREAMP
THAT MEETS REQUIREMENTS
OF NOTE 3
PREAMP
(NOTE 4)
RECOMMENDED CABLE
4 WIRES SHIELDED
22 AWG. SEE NOTE 2
PH
SENSOR
WITH
TC
+PH
SENSOR
RECOMMENDED CABLE
PN 9200273 (UNPREPPED)
PN 23646-01 PREPPED
10 COND, 2 SHIELDS 24 AWG
SEE NOTE 2
NOTES ON SHEET 2 OF 2
8
PREAMP
(NOTE 4)
ATEX APPROVED PREAMP
THAT MEETS REQUIREMENTS
OF NOTE 3
+PH
SENSOR
INFRARED
REMOTE CONTROL UNIT
(RMT PN 23572-00)
FOR USE IN
ZONE 0
+PH
SENSOR
FISCO
ATEX INTRINSIC SAFETY INSTALLATION
7
5
5
4
3
2
1
4
3
2
This document contains information proprietary to
Rosemount Analytical, and is not to be made available
to those who may compete with Rosemount Analytical.
6
6
1
4
3
6
6
2
8
8
8
8
5
5
7
7
7
7
1
4
3
2
1
9
9
9
9
13
14
16 15
13
14
10
10
10
10
11
11
11
12
12
12
16 15
13
14
16 15
13
14
24
16 15
5
5
(ZONE 0)
4
RELEASE DATE
5-6-04
1180
II 1 G
Baseefa02ATEX1284
EEx ia IIC T4
HAZARDOUS AREA
4
ECO NO.
8925
REV
A
ECO
2
FINISH
ANGLES
TOLERANCES
+
-
3
DIMENSIONS ARE IN INCHES
REMOVE BURRS & SHARP EDGES .020 MAX
MACHINED FILLET RADII .020 MAX
NOMINAL SURFACE FINISH 125
+
- .030
+ .010
-
MATERIAL
.XX
.XXX
J. FLOCK
THIS DWG CREATED IN
SOLID EDGE
PROJECT
ENGR APVD
CHECKED J. FLOCK
B. JOHNSON
APPROVALS
DRAWN
2
5/6/04
5/6/04
5/3/04
Uniloc
1
DATE
REV
REV
REV
REV
REV
REV
D
SCALE
SIZE
NONE
DWG NO.
1400293
TYPE
A
Rosemount Analytical,
Uniloc Division
2400 Barranca Pkwy
Irvine, CA 92606
REVISIONS NOT PERMITTED
W/O AGENCY APPROVAL
Baseefa
THIS DOCUMENT IS
CERTIFIED BY
BY
1
SHEET 1 OF
SCHEMATIC, INSTALLATION
5081-P-FI XMTR
ATEX ZONE 0
TITLE
DESCRIPTION
BILL OF MATERIAL
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
SAFETY BARRIER
(SEE NOTES 1 & 7)
DATE
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
SAFETY BARRIER
(SEE NOTES 1 & 7)
UNLESS OTHERWISE SPECIFIED
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
SAFETY BARRIER
(SEE NOTES 1 & 7)
PART NO.
REVISION
DESCRIPTION
UNSPECIFIED
POWER SUPPLY
17.5 VDC MAX
ITEM
UNCLASSIFIED AREA
LTR
SAFETY BARRIER
(SEE NOTES 1 & 7)
3
2
10-96
A
REV
QTY
CHK
A
B
C
D 1400293
MODEL 5081-P-FF/FI
INFRARED REMOTE CONTROLLER
INFRARED REMOTE CONTROLLER (IRC) - KEY FUNCTIONS
The infrared remote controller is used to calibrate and program the transmitter and to display diagnostic messages. See figure below for a description of the function of the keys.
Hold the IRC within 6 feet of the transmitter, and not more than 15 degrees from the center of the display window.
RESET - Press RESET to end the current operation and return to the main
display. Changes will NOT be saved.
RESET does NOT return the transmitter to factory default settings.
HOLD - Press HOLD to access the
prompts used for turning on or off the
hold function.
ENTER - Press ENTER to move from a
submenu to the first prompt under the
submenu. Pressing ENTER also stores
changes in memory and advances to the
next prompt.
ARROW KEYS - Use and keys to
increase or decrease a number or to
scroll through items in a list. Use the or keys to move the cursor across a
number. A flashing word or numeral
shows the position of the cursor.
NEXT - Press NEXT to advance to the
next submenu or to leave a message
screen.
CAL - Press CAL to access the calibration menu.
EXIT - Press EXIT to end the current
operation. Changes are NOT saved.
PROG - Press PROG to access the program menu.
DIAG - Press DIAG to read diagnostic
messages.
Infrared Remote Controller.
SUBSTITUTION OF
C O M P O N E N T S M AY
I M PA I R I N T R I N S I C S A F E T Y
PN 23572-00
WA R N I N G :
TO PREVENT IGNITION
C H A N G E B AT T E R I E S I N
A NONHAZARDOUS AREA
O N LY
IS/I/1/A,B,C & D
NI/I/2/A,B,C & D
T 4 Ta m b = 4 0 ° C
T 3 A Ta m b = 8 0 ° C
YEAR
IRC - INFRARED REMOTE CONTROL
LR 34186
Exia
I N T R I N S I C A L LY S A F E E Q U I P M E N T
H A Z A R D O U S A R E A L O C AT I O N S :
CLASS I, DIV 1, GP A, B, C, D
CLASS I, DIV 2, GP A, B, C, D
T 3 C Ta m b = 4 0 ° C
T 3 Ta m b = 8 0 ° C
1 . 5 V d c A A A B AT T E R I E S
EVEREADY E92/1212
DURACELL MN2400/PC2400
REMOTE CONTROL
B a s e e f a 0 2 AT E X 0 1 9 8
II 1G EExia IIC T4
11 8 0
1 . 5 V d c A A A B AT T E R I E S
EVEREADY E92/1212
DURACELL MN2400/PC2400
R O S E M O U N T A N A LY T I C A L 9 2 6 0 6 U S A
25
MODEL 5081-P-FF/FI
START-UP - pH
START-UP CONFIGURATION AND CALIBRATION — pH
To perform a two-point buffer calibration, follow these steps:
1. Place the pH sensor in the first buffer solution.
2. On the remote, press CAL, ENTER, ENTER.
3. Use the arrow buttons to select the correct buffer value. Press ENTER.
4. Rinse the sensor and place it in the second buffer solution. Press ENTER.
5. Use the arrow buttons to select the correct buffer value. Press ENTER.
PROGRAM
CALIBRATE
CALIbrAtE
Std
tEMP AdJ
CAL bF1
Std 7.00
tEMP 25.0
bF 1
SLOPE 59.01
InPut 58.9
DIAGNOSE
SLOPE
OFFSt
GIMP 1000
rIMP 10
5081-P-FF
SoFt
HArd
nonE
bF1 4.01
CAL bF2
bF 2
bF2 10.01
tEMP
dISPLAY
bUFFEr
rOFFSt 060
tAUtO On
tYPE PH
bAUtO On
tCOEF 00.00
dIAG OFF
tMAn 25.0
tEMP C
bUFFEr Std
ISO 07.00
IMPtC ON
OUtPUt Cur
StAbiLiSE
Snr 07.00
GFH 1500
COdE 000
tIME 10
dIAGnOStIC
GWH 1000
ISOPOtntAL LinE FrEq
PAMP=trAnS
dEFAULt
FActOrY
LinE 60
NO
deLtA 00.02
GWL 020
GFL 010
MENU
CAL 000
Sub-menu
rEF LO
rFH 140
PROMPT
rWH 040
Diag Message
rWL 000
rFL 000
FIGURE 14. Menu Tree for pH
26
FAULtS
YES
MODEL 5081-P-FF/FI
START-UP - ORP
START-UP CONFIGURATION AND CALIBRATION — ORP
To perform a one point standardization, follow these steps.
1. Place the ORP sensor in the ORP buffer solution.
2. On the Remote press CAL, ENTER, ENTER
3. Use the arrow buttons to adjust the value. Press ENTER
4. Press RESET
mV
2511
PROGRAM
CALIBRATE
Std
tEMP ADj
Std 1000
tEMP 25.0
DIAGNOSE
OFFSt 120
rIMP 10
5081-P-FF
SoFt 00.02
HArd 01
FAULtS
nonE
dIAGnOStIC
dISPLAY
LinE FrEq
rOFFSt 060
tYPE ORP
LinE 60
dIAG OFF
tEMP C
IMPtC OFF
OUtPUt CUr
rEF LO
COdE 000
PAMP=trAnS
rFH 140
MENU
Sub-menu
rWH 040
PROMPT
rWL 000
rFL 000
Diag Message
FIGURE 15. Menu Tree for ORP
27
MODEL 5081-P-FF/FI
MENU MNEMONICS
PROGRAM MENU MNEMONICS
5081-P DISPLAY
DBMJcsBuF
Tue
cG2!0!cG3
TMPQF
Ipme
GBVMu
eQo
eJBHopTujd
sPGGTu
JNQuD
HGI
HXKI
HGM
HXKM
DBM
sFG
sGI
sxkI
sGm
sxkM
uFNQ
uBVuP
uNBo
uZQF
ejTQMBZ
MANUAL TEXT
CALIbrAtE
Std
bF1 / bF2
SLOPE
HoLd
FAULt
dPn
dIAGnoStic
rOFFSt
IMPtC
GFH
GWH
GFL
GWL
CAL
rEF
rFH
rWH
rFL
rWL
tEMP
tAUtO
tMAn
tYPE
diSPLAY
The right people,
the right answers,
right now.
MEANING
Calibration menu
Standardize sensor
Buffer 1 / Buffer 2
Sensor slope
Set hold
Set fault
Set output dampening
Diagnostic submenu
Reference offset
Glass impedance temperature compensation
Glass fault high
Glass warning high
Glass fault low
Glass warning low
[Factory use only]
Set high/low impedance reference
Reference fault high
Reference warning high
Reference fault low
Reference warning low
Temperature units
Automatic temperature compensation
Manual temperature compensation
Measurement type (pH/ORP)
Display submenu
ON-LINE ORDERING NOW AVAILABLE ON OUR WEB SITE
http://www.raihome.com
Specifications subject to change without notice.
Credit Cards for U.S. Purchases Only.
Emerson Process Management
Liquid Division
2400 Barranca Parkway
Irvine, CA 92606 USA
Tel: (949) 757-8500
Fax: (949) 474-7250
http://www.raihome.com
© Rosemount Analytical Inc. 2007
Download PDF

advertising