NetSure™ -48V DC Power System
User Instructions, UM582127000 (Issue AC, January 2, 2013)
Specification Number: 582127000
Model Number: 721NPBB
This page is intentionally blank.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
TABLE OF CONTENTS
CONTENTS
PAGE
IMPORTANT SAFETY INSTRUCTIONS .................................................................................. iii
General Safety .................................................................................................................................................... iii
Voltages .............................................................................................................................................................. iii
Battery ................................................................................................................................................................. iii
Circuit Card Handling .......................................................................................................................................... iv
STATIC WARNING ....................................................................................................................v
CHAPTER 1. SYSTEM OVERVIEW ..........................................................................................1
Customer Documentation Package ..................................................................................................................... 1
System Description .............................................................................................................................................. 1
CHAPTER 2. OPERATING PROCEDURES ..............................................................................4
Controller, Rectifiers, and Optional Converters ................................................................................................... 4
ESTOP Function .................................................................................................................................................. 4
ACU+ Battery Charge Current Limit Feature ....................................................................................................... 4
Local Controls and Indicators............................................................................................................................... 4
Circuit Card Locations ................................................................................................................................... 4
System Interface Circuit Card ........................................................................................................................ 6
Optional LVD Driver Circuit Card ................................................................................................................... 7
Optional LVD Driver Lite Circuit Card ............................................................................................................ 8
Optional Manual Battery Disconnect Circuit Card (Main Bay Only) .............................................................. 9
SM-DU Circuit Card ..................................................................................................................................... 10
CHAPTER 3. MAINTENANCE ................................................................................................. 11
System Maintenance Procedures ...................................................................................................................... 11
Adding a Rectifier Module to an Existing Rectifier Module Mounting Shelf Spec. No. 588705000 ................... 11
Adding a Rectifier or Converter Module to an Existing Module Mounting Shelf Spec. No. 588705300 ............ 11
Installing a Field Expansion Rectifier Module Mounting Shelf Spec. No. 588705000 ....................................... 14
Installing a Field Expansion Rectifier/Converter Module Mounting Shelf Spec. No. 588705300 ...................... 18
Changing the ACU+ LVD Control Level for a Contactor .................................................................................... 21
Adding a Supplemental Bay in the Field ............................................................................................................ 21
CHAPTER 4. TROUBLESHOOTING AND REPAIR ................................................................ 22
Contact Information ............................................................................................................................................ 22
Controller, Rectifiers, and Optional Converters ................................................................................................. 22
ACU+ Controller Configuration .......................................................................................................................... 22
System Troubleshooting Information ................................................................................................................. 22
Replacement Information ................................................................................................................................... 25
Replacement Assemblies ............................................................................................................................ 25
Replacement Cables ................................................................................................................................... 25
Replacement Procedures................................................................................................................................... 25
Replacing a Rectifier Module (in a Spec. No. 588705000 Shelf) ................................................................ 25
Replacing a Rectifier or Converter Module (in a Spec. No. 588705300 Shelf) ........................................... 25
Table of Contents
Page i
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Replacing the ACU+ Controller ................................................................................................................... 25
Replacing a Distribution Device ................................................................................................................... 26
Circuit Card Replacement Procedures ........................................................................................................ 37
Replacing a Distribution Panel .................................................................................................................... 53
Replacing a Battery or Load Disconnect Contactor .................................................................................... 56
REVISION RECORD ................................................................................................................ 62
Page ii
Table of Contents
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
IMPORTANT SAFETY INSTRUCTIONS
GENERAL SAFETY
Danger: YOU MUST FOLLOW APPROVED SAFETY PROCEDURES.
Performing the following procedures may expose you to hazards. These
procedures should be performed by qualified technicians familiar with the
hazards associated with this type of equipment. These hazards may
include shock, energy, and/or burns. To avoid these hazards:
a) The tasks should be performed in the order indicated.
b) Remove watches, rings, and other metal objects.
c) Prior to contacting any uninsulated surface or termination, use a
voltmeter to verify that no voltage or the expected voltage is present.
d) Wear eye protection, and use recommended tools.
e) Use double insulated tools appropriately rated for the work to be
performed.
Caution: Performing maintenance and/or troubleshooting procedures may
interrupt power to the loads, if battery reserve is not sufficient.
VOLTAGES
AC Input Voltages
Danger: This system operates from AC voltage capable of producing fatal
electrical shock. AC input power must be completely disconnected from
the branch circuits wiring used to provide power to the system before any
AC electrical connections are made. DO NOT apply AC power to the
system until all electrical connections have been completed and checked.
DC Input/Output Voltages
Danger: This system produces DC Power and may require battery to be connected
to it. Although the DC voltage is not hazardously high, the rectifiers
and/or battery can deliver large amounts of current. Exercise extreme
caution not to inadvertently contact or have any tool inadvertently contact
a battery terminal or exposed wire connected to a battery terminal.
NEVER allow a metal object, such as a tool, to contact more than one
termination or battery terminal at a time, or to simultaneously contact a
termination or battery terminal and a grounded object. Even a momentary
short circuit can cause sparking, explosion, and injury.
BATTERY
Danger: Correct polarity must be observed when connecting battery leads.
Danger: Special safety precautions are required for procedures involving
handling, installing, and servicing batteries. Observe all battery safety
precautions in this manual and in the battery instruction manual. These
precautions should be followed implicitly at all times. Remove watches,
rings, and other metal objects before connecting battery leads.
Important Safety Instructions
Page iii
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
CIRCUIT CARD HANDLING
Warning: Installation or removal of the circuit cards requires careful handling.
Before handling any circuit card, read and follow the instructions
contained on the Static Warning Page.
Page iv
Important Safety Instructions
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
STATIC WARNING
The printed circuit cards used in this equipment contain static sensitive components. The warnings listed below
must be observed to prevent damage to these components. Disregarding any of these warnings may result in
personal injury or damage to the equipment.
1. Strictly adhere to the procedures provided in this document.
2. Before touching any static sensitive component or printed circuit card containing such a component,
discharge all static electricity from yourself by wearing a wrist strap grounded through a one megohm
resistor. Some wrist straps, such as Emerson Network Power Part Number 631810600, have a built-in
one megohm resistor; no external resistor is necessary. Read and follow wrist strap manufacturer’s
instructions outlining use of a specific wrist strap.
3. Do not touch the traces or components on a printed circuit card containing static sensitive components.
Handle the printed circuit card only by the edges that do not have connector pads.
4. After removing a printed circuit card containing a static sensitive component, place the printed circuit card
only on conductive or anti-static material such as conductive foam, conductive plastic, or aluminum foil.
Do not use ordinary Styrofoam or ordinary plastic.
5. Store and ship static sensitive devices or printed circuit cards containing such components only in static
shielding containers.
6. If necessary to repair a printed circuit card containing a static sensitive component, wear an appropriately
grounded wrist strap, work on a conductive surface, use a grounded soldering iron, and use grounded
test equipment.
Static Warning
Page v
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
This Page Left Intentionally Blank
Page vi
Static Warning
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
CHAPTER 1.
SYSTEM OVERVIEW
CUSTOMER DOCUMENTATION PACKAGE
This document (UM582127000) provides User Instructions for NetSure™ Power System
Model 721NPBB, Spec. No. 582127000.
The complete Customer Documentation Package consists of…
Bound System Installation Manual
Power System Installation Instructions:
IM582127000
Power System Quick Start Guide:
QS582127000
Bound ACU+ Controller User Manual
ACU+ Controller User Instructions:
UM1M820BNA
(includes instructions
for 1M820DNA Controller)
USB Drive with All Customer Documentation
Power System Installation Instructions:
IM582127000
Power System Quick Start Guide:
QS582127000
Power System User Instructions:
UM582127000
Power System “System Application Guide”:
SAG582127000
Rectifier Module Mounting Shelf Power Data Sheet:
PD588705000
Rectifier Instructions:
Rectifier/Converter Module Mounting Shelf
Power Data Sheet:
UM1R483500E
PD588705300
Rectifier Instructions:
UM1R482000E3
Converter Instructions:
UM1C48241500
Engineering Drawings
Also provided on the USB drive is an ACU+ configuration drawing and the ACU+
configuration files loaded into the ACU+ as shipped.
SYSTEM DESCRIPTION
-48V DC @ up to 4000 Amperes Power System
The NetSure™ 721NPBB DC Power System is a complete integrated power system
containing rectifiers, optional converters, intelligent control, metering, monitoring, and
distribution.
This power system is designed to power a load while charging a positive grounded
battery. This power system is capable of operating in a batteryless installation or off
battery for maintenance purposes. The power system is designed for operation with the
positive output grounded.
Chapter 1. System Overview
Page 1
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
This system consists of the following components.
Distribution Cabinet
The system always includes a minimum of one distribution cabinet, which provides
DC distribution through fuses and/or circuit breakers. The distribution cabinet is
factory mounted in the relay rack or shipping brackets specified when ordered.
Four different sizes of distribution cabinets are available to accept from one (1) to
four (4) distribution panels. A variety of distribution panels are available that provide
load distribution, battery distribution, and dual voltage load distribution for use with
+24V converters. These distribution panels are configured to accept either bullet
nose type circuit breakers and TPS/TLS fuseholders, TPH fuses, TPL-B fuses, or
GJ/218 circuit breakers.
The distribution cabinet may be equipped with low voltage load disconnect (LVLD),
low voltage battery disconnect (LVBD), and manual battery disconnect.
ACU+ (Advanced Control Unit Plus) Controller
The system contains one controller. The controller provides power system control
(including optional low voltage battery disconnect (LVBD) and low voltage load
disconnect (LVLD) control), rectifier control (including a charge control function),
converter control, metering functions, monitoring functions, and local/remote alarm
functions. The controller also supports rectifier temperature compensation if the
system is equipped with a temperature probe(s). Temperature probe(s) may also be
designated to monitor ambient temperature and/or battery temperature. The
controller also provides data acquisition, system alarm management, and advanced
battery and energy management. The controller contains an LCD display and
keypad for local access. The controller provides Ethernet connection and supports
software upgrade via its USB port. It also comes with a comprehensive web page
and SNMP capability for remote system management. Refer to the ACU+ Controller
Instructions (UM1M820BNA) for more information.
Rectifier Module Mounting Shelf (Spec. No. 588705000)
The system may contain one or more Spec. No. 588705000 rectifier module
mounting shelves, each of which houses up to six (6) rectifier modules. Refer to
Power Data Sheet PD588705000 for more information.
Rectifier Modules (for use in Spec. No. 588705000)
The system contains rectifier modules, which provide load power, battery float
current, and battery recharge current during normal operating conditions. Refer
to the Rectifier Instructions (UM1R483500E) for more information.
Rectifier/Converter Module Mounting Shelf (Spec. No. 588705300)
The system may contain one or more Spec. No. 588705300 rectifier/converter
module mounting shelves, each of which houses rectifier modules and optional
DC-DC converter modules. Refer to Power Data Sheet PD588705300 for more
information.
Rectifier Modules (for use in Spec. No. 588705300)
The system contains rectifier modules, which provide load power, battery float
current, and battery recharge current during normal operating conditions. Refer
to the Rectifier Instructions (UM1R482000E3) for more information.
Page 2
Chapter 1. System Overview
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Optional DC-DC Converter Modules (for use in Spec. No. 588705300)
Where +24V DC load power is also required, DC-DC converter modules are
available. Refer to the Converter Instructions (UM1C48241500) for more
information.
Chapter 1. System Overview
Page 3
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
CHAPTER 2.
OPERATING PROCEDURES
CONTROLLER, RECTIFIERS, AND OPTIONAL CONVERTERS
For operation instructions on these units, refer to the following documents.
ACU+ Controller Instructions (UM1M820BNA)
Rectifier Instructions (UM1R483500E or UM1R482000E3)
Converter Instructions (UM1C48241500)
ESTOP FUNCTION
If an ESTOP switch is wired to the ACU+ IB2 Interface Board, customer-furnished system
ground applied to terminal DI8+ activates the ESTOP function. The ESTOP function
shuts down and locks out the rectifiers, opens the LVD’s, and shuts down the converters.
When the ESTOP signal is removed, LVD’s close (if battery present) and converters
restart. To restart the rectifiers; turn AC power to the rectifiers OFF, wait 30 seconds or
more (until the LEDs on the rectifier extinguish), then turn AC power to the rectifiers ON.
Rectifiers can also be restarted from the ACU+ LCD or WEB Interface menu (via the
Rectifier Reset command, found in the Manual menu in the LCD menus or under the
Rectifier Control Tab in the WEB Interface).
ACU+ BATTERY CHARGE CURRENT LIMIT FEATURE
Functionality: After a commercial AC failure or when some battery cells are permanently
damaged, the current to the batteries can be quite extensive. To avoid overheating or
further damages to the battery, the ACU+ can be programmed to limit the battery current
to a preset level by limiting the charging voltage of the rectifiers. Should the battery
current still exceed a higher preset value, an alarm is issued.
In this system, the ACU+ Battery Charge Current Limit feature is set to be disabled.
Refer to the ACU+ Controller Instructions (UM1M820BNA) to enable and program this
feature, if desired. If enabled, battery charge current is limited to the value set in the
ACU+ Controller, as long as battery voltage is above 47VDC.
LOCAL CONTROLS AND INDICATORS
Refer to the Controller, Rectifier, and Converter Instructions for descriptions of the local
controls and indicators located on these units.
Refer to this section for descriptions of the local controls and indicators located on the
circuit cards installed inside the distribution cabinet.
Circuit Card Locations
Refer to Figure 2-1.
Page 4
Chapter 2. Operating Procedures
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
4-Row Cabinet Shown,
Others Similar
(Front Door Removed in
Illustration for Clarity)
Optional EIB (Main Bay Only)
(ACU+ Extended Interface Board)
(located on inside side panel)
IB2 (Main Bay Only)
(ACU+ Interface Board)
(located on inside side panel)
Optional SM-DU+ and
Shunt Interface Board
ACU+ Controller
(Main Bay)
SM-DU
(Supplemental Bays)
Mounting Position
Optional LVD
Driver Circuit Card
OR
Optional Manual Battery
Disconnect Circuit Card
(Main Bay Only)
System Interface
Circuit Card
Optional LVD Driver
Lite Circuit Card
Figure 2-1
Circuit Card Locations
Chapter 2. Operating Procedures
Page 5
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
System Interface Circuit Card
The system interface circuit card contains test points to externally monitor bay voltage
and bay load. Refer to Figure 2-2.
J7
Bay Load Shunt Scale
List 21, 1-Row Cabinet
800A / 25mV
32A per mV
List 22, 2-Row Cabinet
2000A / 25mV
80A per mV
List 23, 3-Row Cabinet
2500A / 25mV
100A per mV
List 24, 4-Row Cabinet
2500A / 25mV
100A per mV
1
J1
J2
1
1
J3
TB2
J4
J8
1
J10
J5
TB1
TP1 TP2 TP3 TP4
TP1 (+) and TP2 (-)
Bay Voltage
Monitoring
TP3 (+) and TP4 (-)
Bay Load
Shunt Monitoring
Figure 2-2
System Interface Circuit Card
Page 6
Chapter 2. Operating Procedures
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Optional LVD Driver Circuit Card
The optional LVD driver circuit card installed in the main bay contains an LVD inhibit
switch and indicator. Refer to Figure 2-3. LVD driver circuit cards are required for 2-, 3-,
or 4-row distribution cabinets that contain three or more LVD contactors (LVBD and/or
LVLD); or if the distribution cabinet is equipped with an LVBD contactor rated 1200A or
higher.
Caution: If the switch is returned to the ON (normal) position when low voltage
disconnect alarms are active, a low voltage disconnection will occur.
Warning: While the LVD inhibit switch is in the OFF (inhibit) position, a low
voltage disconnection will not occur if battery or load voltage decreases
below the low voltage disconnect setpoint. For maximum battery
protection, this switch should NOT be left in the OFF (inhibit) position.
J6
J5
J4
J9
J3
J2
J1
J7
S1
LVD Inhibit
Active Indicator
Illuminates when the
low voltage disconnect
circuit has been disabled
through the use of the
LVD Inhibit switch.
Switch and indicator located
on circuit card installed in
Main Bay only.
Note: The UP position will not close the LVBD contactor
if the battery is manually disconnected using the
LVD Inhibit Switch
Manual Battery Disconnect Switch.
Momentary UP / Middle / Down
Momentary UP Position: Closes all LVD Contactors (inhibit mode).
Middle Position: OFF (ACU+ DOES NOT control LVD’s) (inhibit mode).
DOWN Position: ON (ACU+ controls LVD’s).
Figure 2-3
Optional LVD Driver Circuit Card
Chapter 2. Operating Procedures
Page 7
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Optional LVD Driver Lite Circuit Card
The optional LVD driver lite circuit card installed in the main bay contains an LVD inhibit
switch and indicator. Refer to Figure 2-4. LVD driver lite circuit cards are required for
distribution cabinets that contain two LVLD contactors or one LVLD contactor and one
LVBD contactor. LVBD contactor must be rated at 600A or lower.
Caution: If the switch is returned to the ON (normal) position when low voltage
disconnect alarms are active, a low voltage disconnection will occur.
Warning: While the LVD inhibit switch is in the OFF (inhibit) position, a low
voltage disconnection will not occur if battery or load voltage decreases
below the low voltage disconnect setpoint. For maximum battery
protection, this switch should NOT be left in the OFF (inhibit) position.
J3
J1
J2
Switch and indicator located
on circuit card installed in
Main Bay only.
S1
LVD Inhibit
Active Indicator
Illuminates when the
low voltage disconnect
circuit has been disabled
through the use of the
LVD Inhibit switch.
Note: The UP position will not close the LVBD contactor
if the battery is manually disconnected using the
Manual Battery Disconnect Switch.
LVD Inhibit Switch
Momentary UP / Middle / Down
Momentary UP Position: Closes all LVD Contactors (inhibit mode).
Middle Position: OFF (ACU+ DOES NOT control LVD’s) (inhibit mode).
DOWN Position: ON (ACU+ controls LVD’s).
Figure 2-4
Optional LVD Driver Lite Circuit Card
Page 8
Chapter 2. Operating Procedures
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Optional Manual Battery Disconnect Circuit Card (Main Bay Only)
The optional manual battery disconnect circuit card contains a manual battery disconnect
switch and indicator. Refer to Figure 2-5.
J2
J1
S1
Manual Battery
Disconnect Switch
Manual Battery Disconnect
Active Indicator
Illuminates if the Battery Disconnect Contactor has
been manually disconnected (placed in open position).
Momentary UP / Middle / Momentary Down
Momentary UP Position:
Closes (latches in close position) the Battery Disconnect Contactor.
Middle Position:
Normal Operation.
Momentary DOWN Position: Opens (latches in open position) the Battery Disconnect Contactor.
Momentarily place switch in the UP position to close the contactor.
Figure 2-5
Optional Manual Battery Disconnect Circuit Card (Main Bay Only)
Chapter 2. Operating Procedures
Page 9
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
SM-DU Circuit Card
The SM-DU is used in supplemental bays in place of ACU+ controller. The SM-DU
monitors the bay and reports to the controller. The controller sends commands to the
SM-DU to fulfill battery management and load control functions according to the received
data.
There are three (3) status and alarm indicators located on the SM-DU. The functions of
these indicators (from top to bottom as shown in the illustration) are as shown in Table
2-1. Refer to Figure 2-6 for location.
Indicator
Normal State
Fault State
Alarm
(Red)
Off
On
A critical or major alarm.
Alarm
(Yellow)
Off
On
A minor alarm.
Off
SM-DU is non-operational.
Operation
(Green)
On
Flashing
Fault Cause
A 1/3Hz flashing indicates the SM-DU
is being identified by the Controller.
A 1Hz flashing indicates a
communication failure.
Table 2-1
SM-DU Indicators
Figure 2-6
SM-DU Circuit Card
Page 10
Chapter 2. Operating Procedures
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
CHAPTER 3.
MAINTENANCE
SYSTEM MAINTENANCE PROCEDURES
It is recommended to perform the maintenance procedures listed in Table 3-1 every
6-months to ensure continual system operation.
PROCEDURE
REFERENCED IN
Check ventilation openings for
obstructions such as dust, papers,
manuals, etc.
Inspect and tighten all installer's
connections.
COMPLETED (√)
-IM582127000,
Chapter 4.
Making Electrical
Connections.
Note: This table may be reproduced as necessary to record and document
system performance.
Table 3-1
Maintenance Procedures to be Performed at 6-Month Intervals
ADDING A RECTIFIER MODULE TO AN EXISTING RECTIFIER
MODULE MOUNTING SHELF SPEC. NO. 588705000
To increase system current capacity, a rectifier module can easily be added to an existing
rectifier module mounting shelf Spec. No. 588705000 that contains an empty rectifier
module mounting position.
It is recommended that the current limit point be checked whenever a rectifier module is
added to or removed from the power system. Refer to “Checking the ACU+ Current Limit
Point after Adding or Removing a Rectifier” in “CHAPTER 4. TROUBLESHOOTING AND
REPAIR”.
The rectifier module being added is assigned by the ACU+ the lowest available
identification number. If desired, you can change the identification number, see
“Configuring the ACU+ Identification of Rectifiers” in Chapter 5 of the separate Power
System Installation Instructions (IM582127000).
For rectifier module installation instructions, refer to Rectifier Instructions
(UM1R483500E).
ADDING A RECTIFIER OR CONVERTER MODULE TO AN
EXISTING MODULE MOUNTING SHELF SPEC. NO. 588705300
To increase system current capacity, a rectifier module can easily be added to an existing
module mounting shelf Spec. No. 588705300 that contains an empty rectifier module
mounting position. Likewise, to increase subsystem capacity a DC-DC converter module
can be added to a module mounting shelf Spec. No. 588705300 that contains an empty
converter module mounting position.
Rectifier and converter modules can be inserted or removed with power applied (hot
swappable).
Chapter 3. Maintenance
Page 11
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Rectifiers modules can be installed in any mounting position of each module mounting
shelf. Converters modules can be installed in any of the three far right mounting
positions of each module mounting shelf (as viewed from the front). See Figure 3-1.
Note: Each rectifier and converter module locks into the module mounting shelf by
means of a latch located on the bottom of the module. The latch and module
handle are interactive. Pushing the handle up into the module’s front panel
causes the latch to extend to the locking position; pulling the handle down out
from the module’s front panel causes the latch to retract. See Figure 3-1.
Warning: To prevent damage to the latching mechanism, ensure the handle is in
the open position when installing or removing a module. NEVER hold
the handle in the closed position when installing a module into a shelf.
Procedure
1) Unpack the modules.
2) Note the model number located on the front of each module. Model numbers
starting with the letter “R” are rectifier modules. Model numbers starting with the
letter “C” are converter modules.
3) Place the module into an unoccupied mounting position without sliding it in
completely. Rectifiers modules can be installed in any mounting position of each
module mounting shelf. Converters modules can be installed in any of the three
far right mounting positions of each module mounting shelf (as viewed from the
front). See Figure 3-1.
4) Loosen the captive screw on the module’s handle. Pull the handle down out from
the module’s front panel (this will also retract the latch mechanism). See Figure
3-1.
5) Push the module completely into the shelf.
6) Push the handle up into the module’s front panel. This will lock the module
securely to the shelf. Tighten the captive screw on the handle.
7) Repeat the above steps for each module being installed in the system.
8) After the modules are physically installed in the mounting shelf(s), they are ready
for operation immediately after power is supplied to them.
Note: It is recommended that the current limit point be checked whenever a rectifier
is added to or removed from the power system. Refer to “Checking the ACU+
Current Limit Point after Adding or Removing a Rectifier” in “CHAPTER 4.
TROUBLESHOOTING AND REPAIR”.
Note: The rectifier or converter being added is assigned by the ACU+ the lowest
available identification number. If desired, you can change the identification
number, see “Configuring the ACU+ Identification of Rectifiers” or
“Configuring the ACU+ Identification of Converters” in Chapter 5 of the
separate Power System Installation Manual (IM582127000).
Page 12
Chapter 3. Maintenance
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Module Mounting Shelf(s)
Front View
Rectifier
Mounting Positions
Rectifier or Converter
Mounting Positions
Rectifier
Converter
Captive Screw
Captive Screw
Handle
Handle
Latch
Latch
Figure 3-1
Installing Rectifier and Converter Modules in a Spec. No. 588705300 Shelf
Chapter 3. Maintenance
Page 13
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
INSTALLING A FIELD EXPANSION RECTIFIER MODULE
MOUNTING SHELF SPEC. NO. 588705000
Danger: Adhere to the “Important Safety Instructions” presented at the front of
this document.
Note: Refer to Figure 3-2 and Figure 3-3 as this procedure is performed.
Procedure
1) Install the expansion rectifier module mounting shelf directly below the bottommost rectifier module mounting shelf in the rack. Use the mounting hardware
provided in the expansion busbar kit.
Hardware build-up is:
12-24 x 3/4" screw and flat washer, (1) set per side.
12-24 x 3/4" screw and ground washer, (1) set per side.
Note: Install the ground washers so the teeth make contact with the metal on
the mounting angles. Torque all screws to 65 in-lbs.
2) On the rear of the expansion rectifier module mounting shelf and the existing
shelf installed directly above it, remove the rear shield that covers the output
busbars.
Note: Apply electrical anti-oxidizing compound to busbar mating surfaces before
performing the next step.
3) Secure the existing shelf’s busbars to the expansion shelf’s mating busbars with
the supplied interconnect busbars and hardware.
Hardware build-up for these connections are:
1/4-20 x 1" bolt,
1/4" Belleville lock washer,
1/4" flat washer.
Install the Belleville lock washer so the concave side is towards the busbar.
Torque all connections to 60 in-lbs.
If installing a second expansion rectifier module mounting shelf, 1/4-20 nuts
(included) are required in lieu of the 1/4-20 x 1” bolts (see Figure 3-2).
4) Disconnect the cable coming from the distribution cabinet from the bottom
connector on the bottom-most existing rectifier shelf.
5) Connect the bottom connector on the bottom-most existing rectifier shelf to the
top connector on the expansion rectifier shelf.
6) Connect the cable disconnected in step 4) (coming from distribution cabinet) to
the bottom connector on expansion rectifier shelf.
7) Replace the rear covers removed in step 2) above.
8) Refer to the Power System Installation Instructions (IM582127000) and connect
AC input power to the expansion shelf.
9) Refer to the Rectifier Instructions and install rectifier modules into the expansion
shelf as required.
Page 14
Chapter 3. Maintenance
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Front View
(Install Expansion
Rectifier Module Mounting Shelf)
Rear View
(Remove Rear Shield from
Rectifier Module Mounting Shelf
and Shelf Above It)
Figure 3-2 (cont’d on next page)
Installing a Field Expansion Rectifier Module Mounting Shelf Spec. No. 588705000
Chapter 3. Maintenance
Page 15
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Rear View
(Install Output Busbars from Kit)
Completed View
1st
Expansion
Shelf
2nd
Expansion
Shelf
Figure 3-2 (cont’d from previous page)
Installing a Field Expansion Rectifier Module Mounting Shelf Spec. No. 588705000
Page 16
Chapter 3. Maintenance
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Distribution
Cabinet Wire
Harness
Slate and
Slate/White Wires
Brown and
Brown/White Wires
These cables are
factory connected.
Existing
Rectifier Module
Mounting Shelf
These cables are
factory connected.
Existing
Rectifier Module
Mounting Shelf
These cables are
factory connected.
Existing
Rectifier Module
Mounting Shelf
Disconnect cable coming from distribution
cabinet from this connector on bottom-most
existing rectifier shelf, then connect to the
top connector on the expansion rectifier shelf.
Expansion
Rectifier Module
Mounting Shelf
Connect the cable disconnected above
(coming from distribution cabinet) to bottom
connector on expansion rectifier shelf.
Exploded View Shown to Illustrate Wire Connections Only
Figure 3-3
ACU+ CAN Bus, Rectifier Module Mounting Shelf Spec. No. 588705000
Chapter 3. Maintenance
Page 17
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
INSTALLING A FIELD EXPANSION RECTIFIER/CONVERTER
MODULE MOUNTING SHELF SPEC. NO. 588705300
Danger: Adhere to the “Important Safety Instructions” presented at the front of
this document.
Note: Refer to Figure 3-4 and Figure 3-5 as this procedure is performed.
Procedure
1) Remove the busbar rear shield from the existing rectifier/converter shelves.
Remove the cut-out panel from the busbar rear shield by gently bending the
panel until it snaps from the busbar rear shield.
2) Remove the hardware from the lowest module mounting shelf’s -48V, return, and
+24V (if present) busbars.
3) Install the expansion module mounting shelf directly below the bottom-most
module mounting shelf in the rack. Use the mounting hardware provided with the
expansion module mounting shelf.
Hardware build-up is:
12-24 x 3/4" screw and flat washer, (1) set per side.
12-24 x 3/4" screw and ground washer, (1) set per side.
Note: Install the ground washers so the teeth make contact with the metal on
the mounting angles. Torque all screws to 65 in-lbs.
4) Remove the busbar rear shield from the expansion module mounting shelf.
Note: Apply electrical anti-oxidizing compound to busbar mating surfaces before
performing the next step.
5) Install the busbars provided with the expansion module mounting shelf between
the studs on the expansion module mounting shelf and the studs on the shelf
above it. Secure these busbars to the expansion module mounting shelf with the
hardware provided with the expansion module mounting shelf. Secure these
busbars to the shelf above the expansion module mounting shelf with the
hardware previously removed. Torque to 60 in-lbs.
Hardware build-up for these connections are:
M6 Nut,
M6 Belleville lock washer,
M6 flat washer.
6) Disconnect the cable coming from the distribution cabinet from the connector on
the bottom-most existing module mounting shelf and connect this cable to the
same connector on the expansion module mounting shelf.
7) Connect the open connector on the bottom-most existing module mounting shelf
to the open connector on the expansion module mounting shelf.
8) Re-install the rear busbar shield previously removed from the existing module
mounting shelf. Re-install the rear busbar shield previously removed from the
expansion module mounting shelf.
9) Refer to the Power System Installation Instructions (IM582127000) and connect
AC input power to the expansion module mounting shelf.
10) Refer to the Power System Installation Instructions (IM582127000) and install
rectifier and converter modules into the expansion module mounting shelf as
required.
Page 18
Chapter 3. Maintenance
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
1. Remove busbar rear shield from
existing rectifier/converter shelves.
Remove the cut-out panel
from the busbar rear shield.
Busbar Rear Shield
Cut-Out Panel
2. Remove hardware from the
lowest module mounting shelf’s
-48V, return, and +24V (if present)
busbars.
Rear
3. Install the expansion module
mounting shelf into the rack.
4. Remove busbar rear shield from
expansion module mounting shelf.
Front
Rear
5. Install the busbars provided
with the expansion module
mounting shelf between the
shelves. Torque to 60 in-lbs.
6. Re-install the rear busbar
shields previously removed.
Figure 3-4
Installing a Field Expansion Module Mounting Shelf Spec. No. 588705300
Chapter 3. Maintenance
Page 19
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Distribution
Cabinet Wire
Harness
Exploded View Shown to
Illustrate Wire Connections Only
Slate and
Slate/White Wires
Existing Module
Mounting Shelf
Brown and
Brown/White
Wires
These connectors
are factory connected.
Rear View
Factory provided jumper
to bring connectors to
same side of shelf.
Existing Module
Mounting Shelf
These connectors
are factory connected.
Rear View
Factory provided jumper
to bring connectors to
same side of shelf.
Existing Module
Mounting Shelf
These connectors
are factory connected.
Rear View
X
Factory provided jumper
to bring connectors to
same side of shelf.
Disconnect cable coming
from distribution cabinet
from this connector on
bottom-most existing
shelf, then connect to the
same connector on the
expansion shelf.
Expansion Module
Mounting Shelf
Rear View
Now connect these
two connectors together.
Factory provided jumper
to bring connectors to
same side of shelf.
Figure 3-5
ACU+ CAN Bus, Rectifier Module Mounting Shelf Spec. No. 588705300
Page 20
Chapter 3. Maintenance
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
CHANGING THE ACU+ LVD CONTROL
LEVEL FOR A CONTACTOR
The ACU+ Controller has two available LVD control levels (LVD1 and LVD2). The level
used to control a contactor is determined by which connector on the LVD circuit card its
control leads are plugged into. To change the LVD control level for a contactor, simply
switch which LVD connector it is plugged into (if an open connector is available) on the
LVD circuit card. Refer to Figure 4-14 and Figure 4-15 for connector location and
function.
Note: DO NOT change a Low Voltage Load Disconnect contactor to LVD Control Level
2 (LVD2) if the system is furnished with a Low Voltage Battery Disconnect
contactor.
ADDING A SUPPLEMENTAL BAY IN THE FIELD
Refer to the Power System Installation Instructions (IM582127000) for procedures
detailing mounting and wiring of the supplemental bay.
Supplied with the supplemental bay is a USB drive which contains a “SettingParam.run”
file. Download this file into the ACU+ Controller to program the ACU+ Controller for use
with the newly installed supplemental bay. Refer to the ACU+ Instructions
(UM1M820BNA) for a download procedure. There are also labels located near the
SM-DU and SM-DU+ in the supplemental bay that detail the ACU+ settings for this bay.
Once the ACU+ has been programmed for the newly installed supplemental bay, refer to
the ACU+ Instructions (UM1M820BNA) and save a copy of the “SettingParam.run” file.
Chapter 3. Maintenance
Page 21
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
CHAPTER 4.
TROUBLESHOOTING AND REPAIR
CONTACT INFORMATION
Support contact information is provided on the inside of the back cover of this document.
CONTROLLER, RECTIFIERS, AND OPTIONAL CONVERTERS
For troubleshooting and repair instructions on these units, refer to the following
documents.
ACU+ Controller Instructions (UM1M820BNA)
Rectifier Instructions (UM1R483500E or UM1R482000E3)
Converter Instructions (UM1C48241500)
ACU+ CONTROLLER CONFIGURATION
If any ACU+ Controller configuration settings were changed, refer to the ACU+
Instructions (UM1M820BNA) and save a copy of the configuration file. This file can be
used to restore the ACU+ Controller settings, if required, at a later date.
Note that provided on a USB drive furnished with the system is an ACU+
configuration drawing (C-drawing) and the ACU+ configuration files loaded into the
ACU+ as shipped.
SYSTEM TROUBLESHOOTING INFORMATION
This system is designed for ease in troubleshooting and repair. The various indicators as
described in CHAPTER 2. OPERATING PROCEDURES and in the Controller, Rectifier,
and Converter Instructions are designed to isolate failure to a specific element. Once the
faulty element has been identified, refer to “Replacement Information” and "Replacement
Procedures" in this chapter.
Troubleshooting Alarm Conditions on the ACU+ Controller
The ACU+ Controller displays alarm conditions as listed in the Available Alarms section
of the ACU+ Instructions (UM1M820BNA). Programmable external alarm relays are also
available. Refer to the System Installation Instructions (IM582127000) and the
configuration drawing (C-drawing) supplied with your power system documentation for
your alarm relay configurations.
The ACU+’s Active Alarm and Alarm History submenus allow the User to view alarm
details. Refer to the ACU+ Instructions (UM1M820BNA) to access these menus.
Checking the ACU+ Current Limit Point after Adding or Removing a Rectifier
If a rectifier is added to the power system, the system current limit point will automatically
increase by the percentage each existing rectifier was set to provide prior to the addition.
If a rectifier is removed from the system (and the Rect Comm Fail alarm is reset), the
current limit point will remain unchanged unless the capacity of the remaining rectifiers is
not sufficient to maintain the present current limit point. If that happens, the current limit
point will automatically increase to the maximum (121% of the remaining rectifiers).
It is recommended that the current limit point be checked whenever a rectifier is added to
or removed from the power system.
Page 22
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Procedure
1) With the Main screen displayed, press ENT to go to the Main Menu. Navigate to
and select “Settings” (ENT).
2) If a password screen opens, a password must be entered to allow the User to
make adjustments. If a password was previously entered and has not yet timed
out, skip this step and proceed to step 3). Otherwise, to enter a password, with
the cursor at the User Name field (default is “Admin”), press the down arrow key
to move cursor down to the password line. Press ENT. “0” is highlighted. Press
the up arrow key once to change the “0” to”1” (default password is “1”), then
press ENT twice. (Note: If you have been assigned a unique User Name and
password, follow this procedure to enter these.)
3) With the Settings menu screen displayed, navigate to and select “Rectifier”
(ENT) / “All Rect Set” (ENT).
4) Navigate to “Current Limit Pt”. The current limit in amperes is displayed. If no
change is required, go to step 6). To make a change, proceed with step 5).
5) With the cursor at “Current Limit Pt”, press ENT to change the current limit point.
Use the up or down arrow keys to set as desired, then press ENT.
6) Return to the Main screen by repeatedly pressing ESC (escape).
Clearing a Rectifier Communications Fail Alarm after Removing a Rectifier
If a rectifier module is removed from the system, a rectifier communications failure alarm
is generated. If the rectifier module will not be replaced, the alarm should be cleared as
described in the following procedure.
Procedure
1) With the Main screen displayed, press ENT to go to the Main Menu. Navigate to
and select “Manual” (ENT).
2) If a password screen opens, a password must be entered to allow the User to
make adjustments. If a password was previously entered and has not yet timed
out, skip this step and proceed to step 3). Otherwise, to enter a password, with
the cursor at the User Name field (default is “Admin”), press the down arrow key
to move cursor down to the password line. Press ENT. “0” is highlighted. Press
the up arrow key once to change the “0” to”1” (default password is “1”), then
press ENT twice. (Note: If you have been assigned a unique User Name and
password, follow this procedure to enter these.)
3) With the Manual menu screen displayed, navigate to and select “Rectifier” (ENT)
/ “All Rect Ctrl” (ENT).
4) Navigate to “Clear Comm Fail”. Press ENT. “Yes” highlights.
5) Press ENT to select the operation. Press ENT again to confirm.
6) Return to the Main screen by repeatedly pressing ESC (escape).
Clearing a Converter Communications Fail Alarm after Removing a Converter
If a converter module is removed from the system, a converter communications failure
alarm is generated. If the converter module will not be replaced, the alarm should be
cleared as described in the following procedure.
Procedure
1) With the Main screen displayed, press ENT to go to the Main Menu. Navigate to
and select “Manual” (ENT).
Chapter 4. Troubleshooting and Repair
Page 23
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
2) If a password screen opens, a password must be entered to allow the User to
make adjustments. If a password was previously entered and has not yet timed
out, skip this step and proceed to step 3). Otherwise, to enter a password, with
the cursor at the User Name field (default is “Admin”), press the down arrow key
to move cursor down to the password line. Press ENT. “0” is highlighted. Press
the up arrow key once to change the “0” to”1” (default password is “1”), then
press ENT twice. (Note: If you have been assigned a unique User Name and
password, follow this procedure to enter these.)
3) With the Manual menu screen displayed, navigate to and select “Converter”
(ENT) / “All Conv Ctrl” (ENT).
4) Navigate to “Clear Comm Fail”. Press ENT. “Yes” highlights.
5) Press ENT to select the operation. Press ENT again to confirm.
6) Return to the Main screen by repeatedly pressing ESC (escape).
Clearing a Rectifier Lost Alarm
If the ACU+ Controller resets while a rectifier communications fail alarm is active, the
rectifier communications fail alarm is replace with a rectifier lost alarm. To clear the
alarm, perform the following procedure.
Procedure
1) With the Main screen displayed, press ENT to go to the Main Menu. Navigate to
and select “Manual” (ENT).
2) If a password screen opens, a password must be entered to allow the User to
make adjustments. If a password was previously entered and has not yet timed
out, skip this step and proceed to step 3). Otherwise, to enter a password, with
the cursor at the User Name field (default is “Admin”), press the down arrow key
to move cursor down to the password line. Press ENT. “0” is highlighted. Press
the up arrow key once to change the “0” to”1” (default password is “1”), then
press ENT twice. (Note: If you have been assigned a unique User Name and
password, follow this procedure to enter these.)
3) With the Manual menu screen displayed, navigate to and select “Rectifier” (ENT)
/ “All Rect Ctrl” (ENT).
4) Navigate to “Clear Rect Lost”. Press ENT. “Clear” highlights.
5) Press ENT to select the operation. Press ENT again to confirm.
6) Return to the Main screen by repeatedly pressing ESC (escape).
Clearing a Converter Lost Alarm
If the ACU+ Controller resets while a converter communications fail alarm is active, the
converter communications fail alarm is replace with a converter lost alarm. To clear the
alarm, perform the following procedure.
Procedure
1) With the Main screen displayed, press ENT to go to the Main Menu. Navigate to
and select “Manual” (ENT).
2) If a password screen opens, a password must be entered to allow the User to
make adjustments. If a password was previously entered and has not yet timed
out, skip this step and proceed to step 3). Otherwise, to enter a password, with
the cursor at the User Name field (default is “Admin”), press the down arrow key
to move cursor down to the password line. Press ENT. “0” is highlighted. Press
the up arrow key once to change the “0” to”1” (default password is “1”), then
Page 24
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
press ENT twice. (Note: If you have been assigned a unique User Name and
password, follow this procedure to enter these.)
3) With the Manual menu screen displayed, navigate to and select “Converter”
(ENT) / “All Conv Ctrl” (ENT).
4) Navigate to “Clear Conv Lost”. Press ENT. “Clear” highlights.
5) Press ENT to select the operation. Press ENT again to confirm.
6) Return to the Main screen by repeatedly pressing ESC (escape).
REPLACEMENT INFORMATION
Replacement Assemblies
When a trouble symptom is localized to a faulty rectifier module, converter module,
controller, or system circuit card; that particular device or circuit card should be replaced
in its entirety. No attempt should be made to troubleshoot or repair individual
components on any rectifier module, converter module, controller, or circuit card.
Refer to SAG582127000 (System Application Guide) for replacement part numbers.
Replacement Cables
Refer to SAG582127000 (System Application Guide) for replacement part numbers.
REPLACEMENT PROCEDURES
Danger: Adhere to the “Important Safety Instructions” presented at the front of this
document.
Replacing a Rectifier Module (in a Spec. No. 588705000 Shelf)
Refer to the Rectifier Instructions (UM1R483500E) for a rectifier module replacement
procedure. Refer also to System Troubleshooting Information in this chapter.
The rectifier module being replaced is assigned by the ACU+ the lowest available
identification number. If desired, you can change the identification number, see
“Configuring the ACU+ Identification of Rectifiers” in Chapter 5 of the separate Power
System Installation Instructions (IM582127000).
Replacing a Rectifier or Converter Module (in a Spec. No. 588705300 Shelf)
Refer to the Rectifier User Instructions (UM1R482000E3) or Converter User Instructions
(UM1C48241500) for a rectifier and converter module replacement procedure. Refer
also to System Troubleshooting Information in this chapter.
The rectifier or converter module being replaced is assigned by the ACU+ the lowest
available identification number. If desired, you can change the identification number, see
“Configuring the ACU+ Identification of Rectifiers” or “Configuring the ACU+ Identification
of Converters” in Chapter 5 of the separate Power System Installation Manual
(IM582127000).
Replacing the ACU+ Controller
Refer to the ACU+ Instructions (UM1M820BNA) for a controller replacement procedure.
Chapter 4. Troubleshooting and Repair
Page 25
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Replacing a Distribution Device
General
Replace distribution devices with the same type and rating. Refer to System Application
Guide SAG582127000 for part numbers.
Distribution Fuse “Alarm Fuse” Replacement
If a distribution fuse opens, the associated alarm fuse opens. Replace the distribution
fuse before replacing the alarm fuse.
Procedure
1) An alarm fuse is removed by pulling it straight out of the fuseholder. If the alarm
fuse is located in a modular fuse carrier, hold the fuse carrier in place with your
thumb while pulling on the alarm fuse to prevent the entire carrier from
inadvertently being pulled out.
2) Safety fuse covers are provided for all Bussmann GMT type fuses installed in the
system. These covers snap onto the fuses and provide protection from exposed
electrical terminations when a fuse opens. Insure that the safety fuse cover is
installed after replacing a fuse. Refer to Figure 4-1 for installation details.
Safety Cover
P/N 248898700
(GMT-X)
Safety Cover
P/N 102774
(GMT-Y)
Figure 4-1
Installation of Safety Fuse Covers
Page 26
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Replacing a TPS/TLS Fuse
Procedure
Note: Refer to Figure 4-2 as this procedure is performed.
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Remove the fuse carrier from the mounted fuseholder body by pulling it straight
out.
3) Remove the open fuse from the fuse carrier and replace it with the same type
and rating.
4) Replace the alarm fuse located in the front of the fuse carrier with the same type
and rating. Ensure that a plastic safety cover is installed on the alarm fuse.
5) Push the fuse carrier securely back into the mounted fuseholder body. Note that
a polarizing key on the bottom of the carrier prevents the carrier from being
inserted upside down.
6) Verify no Fuse Alarms are active.
7) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
Shorter Side
to the Top
Insert these terminals
into corresponding sockets
on distribution panel.
Fuseholder Assembly
Fuseholder Body
TPS/TLS Fuse
GMT-X
Safety Fuse Cover
(Replacement
P/N 248898700)
Longer Side
to the Bottom
Fuse Carrier
GMT-18/100A
Alarm Fuse
(Replacement
P/N 248610301)
Fuseholder Assembly
Exploded View
Polarizing Keyway
Matches Key on
Bottom of Fuse Carrier
Fuseholder Assembly (P/N 117201) includes
body & carrier, alarm fuse, and alarm fuse safety cover.
Figure 4-2
Replacing a TPS/TLS Fuseholder and/or Fuse
Chapter 4. Troubleshooting and Repair
Page 27
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Replacing a Bullet Nose Fuseholder
Procedure
Note: Refer to Figure 4-2 as this procedure is performed.
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Remove the fuse carrier from the mounted fuseholder body by pulling it straight
out. Hold the fuseholder body while you pull the fuse carrier from the body.
3) Gently rock the defective fuseholder up and down while pulling firmly outward
until the fuseholder is free from the distribution panel.
4) Orient the fuseholder as shown in Figure 4-2. Insert the terminals on the rear of
the fuseholder into their corresponding sockets on the distribution panel. Ensure
the alarm contact on the back of the fuseholder makes contact with the alarm
terminal on the spring strip. Push fuseholder in firmly until fully seated in the
distribution panel.
5) Push the fuse carrier securely back into the mounted fuseholder body. Note that
a polarizing key on the bottom of the carrier prevents the carrier from being
inserted upside down.
6) Verify no Fuse Alarms are active.
7) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
Page 28
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Replacing a Bullet Nose Circuit Breaker
Procedure
Note: Refer to Figure 4-3 as this procedure is performed.
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Operate the defective circuit breaker to the OFF position.
3) Gently rock the defective circuit breaker up and down while pulling firmly outward
until the breaker is free from the distribution panel.
4) Ensure that the circuit breaker is in the OFF position, and is of the correct rating.
5) Orient the circuit breaker as shown in Figure 4-3. Insert the terminals on the rear
of the circuit breaker into their corresponding sockets on the distribution panel.
Ensure the alarm contact on the back of the circuit breaker makes contact with
the alarm terminal on the spring strip. Push distribution device in firmly until fully
seated in the distribution panel.
6) Operate the replacement circuit breaker to the ON position.
7) Verify no Circuit Breaker Alarms are active.
8) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
Shorter Side
to the Top
Lettering on
handle must be
right side up.
Insert these terminals
into corresponding sockets
on distribution panel.
Turn off
before installing.
Longer Side
to the Bottom
Figure 4-3
Replacing a Bullet Nose Circuit Breaker
Chapter 4. Troubleshooting and Repair
Page 29
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Replacing a TPH Fuse
Procedure
Note: Refer to Figure 4-4 as this procedure is performed.
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Remove the fuse carrier from the mounted fuseholder body by grasping its
handle and pulling straight out.
3) Remove the open fuse from the fuse carrier and replace it with the same type
and rating.
4) Push the fuse carrier securely back into the mounted fuseholder body.
5) On the distribution panel, locate the open alarm fuse associated with the TPH
fuse being replaced. Replace the alarm fuse with the same type and rating.
Ensure that a plastic safety cover is installed on the alarm fuse.
6) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
Fuse
Fuseholder Body
Fuse Carrier
Figure 4-4
Replacing a TPH Fuse
Page 30
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Replacing a TPL-B Fuse
Procedure
Note: Refer to Figure 4-5 as this procedure is performed.
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Remove the fuse case from the mounted fuse block by grasping its handle and
pulling it straight out.
3) Open the fuse case.
4) Remove the open fuse from the fuse case and replace it with the same type and
rating.
5) Close the fuse case.
6) Push the fuse case securely back into the mounted fuse block.
7) Replace the alarm fuse located in the front of the TPL-B fuse block. Replace
only with a fuse of the same type and rating. Ensure that a plastic safety cover is
installed on the alarm fuse.
8) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
GMT-18/100A Alarm Fuse
(P/N 248610301) and
GMT-X Safety Fuse Cover
(P/N 248898700)
(Both are provided
w/ fuseblock)
Fuse Installed in
Open Fuse Case
(rear view)
Fuseblock
(P/N 516241)
TPL Fuse
Fuse Case
Fuse Installed in
Closed Fuse Case
(rear view)
Open Fuse Case View
Figure 4-5
Replacing a TPL-B Fuse
Chapter 4. Troubleshooting and Repair
Page 31
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Replacing a GJ/218 Circuit Breaker
Procedure
Note: Refer to Figure 4-6 as this procedure is performed.
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Operate the defective circuit breaker to the OFF position.
Danger: The bolts being removed in the following step may be at system
potential. Use insulated tools.
3) Remove the hardware securing the circuit breaker to the distribution panel and
partially remove the circuit breaker.
4) Record each alarm wire located on the back of the circuit breaker (color and
location on circuit breaker). Wiring diagrams are provided in Figure 4-6, Figure
4-7, and Figure 4-8. Carefully disconnect the alarm wiring from the back of the
circuit breaker, ensuring the exposed end does not contact any energized circuit.
5) Shunted Breakers Only: Record each shunt wire located on the back of the
circuit breaker (color and location on circuit breaker). Wiring diagrams are
provided in Figure 4-6, Figure 4-7, and Figure 4-8. Carefully disconnect the
shunt wiring from the back of the circuit breaker, ensuring the exposed end does
not contact any energized circuit.
6) Ensure that the replacement circuit breaker is in the OFF position, and is of the
correct rating and type (electrical trip/mechanical trip or electrical trip only).
Orient the circuit breaker over its mounting location. Re-attach the alarm wiring
and shunt wiring (if applicable) to the back of the circuit breaker as recorded
above. Wiring diagrams are provided in Figure 4-6, Figure 4-7, and Figure 4-8.
Danger: The bolts being installed in the following step may be at system
potential. Use insulated tools.
7) Install the replacement circuit breaker into its mounting position and secure with
the hardware previously removed. Torque to 60 in-lbs.
8) Transfer the circuit breaker guard from the old circuit breaker to the new circuit
breaker.
9) Operate the replacement circuit breaker to the ON position.
10) Verify no Circuit Breaker Alarms are active.
11) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
Page 32
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
INSTALLING CIRCUIT BREAKER
Alarm jumper connector.
Holes to route shunt jumper through (if applicable).
ON
OFF
Apply anti-oxidizing compound to busbar mating
surfaces before mounting circuit breakers.
1/4" Hardened
Flat Washer
1/4" Belleville
Lock Washer
1/4-20 x 3/4” Bolt
(2 places)
Torque to 60 in-lbs.
INSTALLING CIRCUIT BREAKER GUARD
ALARM WIRING (BREAKERS W/OUT SHUNTS)
ALARM WIRING (BREAKERS WITH SHUNTS)
Figure 4-6 (cont’d on next page)
Replacing a GJ/218 Circuit Breaker (1-Pole)
Chapter 4. Troubleshooting and Repair
Page 33
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Alarm jumper connectors.
INSTALLING CIRCUIT BREAKER
Holes to route shunt jumper through (if applicable).
2-pole breaker shown.
3-pole and 4-pole breakers similar.
ON
OFF
Busbar
Apply anti-oxidizing compound to busbar mating
surfaces before mounting circuit breakers.
INSTALLING CIRCUIT BREAKER GUARD
ALARM WIRING (BREAKERS W/OUT SHUNTS)
1/4" Hardened
Flat Washer
1/4" Belleville
Lock Washer
1/4-20 x 3/4” Bolt
(4 places / 2-pole brk,
6 places / 3-pole brk,
8 places / 4-pole brk)
Torque to 60 in-lbs.
ALARM WIRING (BREAKERS WITH SHUNTS)
Figure 4-6 (cont’d from previous page)
Installing a GJ/218 Circuit Breaker (2-Pole, 3-Pole, 4-Pole)
Page 34
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
List AC Only
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Figure 4-7
GJ/218 Circuit Breaker Wiring Diagram (List AC and AD)
Chapter 4. Troubleshooting and Repair
Page 35
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
List BC Only
UM582127000
Issue AC, January 2, 2013
Figure 4-8
GJ/218 Circuit Breaker Wiring Diagram (List BC and BD)
Page 36
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Circuit Card Replacement Procedures
Warning: Circuit cards used in this power system contain static-sensitive devices.
Read the Static Warning at the front of this document before performing
any of the following procedures.
General
The following circuit card replacement procedures can be performed with the system
operating.
Refer to Figure 2-1 for circuit card locations.
Caution: When performing any step in these procedures that requires removal or
installation of hardware, use caution to ensure no hardware is dropped
and left inside the cabinet; otherwise service interruption or equipment
damage may occur.
Note: When performing any step in these procedures that requires removal of existing
hardware, retain all hardware for use in subsequent steps.
System Interface Circuit Card Replacement
Procedure
1) Performing this procedure may activate external alarms. Do one of the following.
If possible, disable these alarms. If these alarms cannot be easily disabled,
notify the appropriate personnel to disregard any future alarms associated with
this system while the procedure is being performed.
Danger: Performing the next steps exposes service personnel to battery
potential. Exercise extreme caution not to inadvertently contact or
have any tool inadvertently contact any energized electrical
termination.
2) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
Warning: Damage to the circuit card may result if the next step is not followed.
3) Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.
4) Remove the top and front panels to access the circuit cards at the bottom of the
distribution cabinet.
5) Carefully label any wires connected to the customer connection terminal block on
the circuit card. These wires must be connected to the same terminals on the
replacement circuit card. Refer to Figure 4-9.
6) Carefully label the connectors plugged into the circuit card. These connectors
must be plugged into the same connectors on the replacement circuit card.
Refer to Figure 4-9.
Danger: In the next step, external wiring may be energized from an external
source. DO NOT allow bare wire ends to contact any grounded or
energized object.
7) Remove the external wiring from the customer connection terminal block. DO
NOT allow the bare wire end to contact any grounded or energized object.
Isolate the wire end with electrical tape. Repeat for each wire to be removed.
8) Unplug all connectors plugged into the circuit card.
Chapter 4. Troubleshooting and Repair
Page 37
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
9) Remove the screws securing the circuit card and remove the circuit card from the
distribution cabinet.
10) In this step, ensure you do not intermix the old and replacement circuit cards.
Set the shorting jumpers on the replacement circuit card to match the locations
on the old circuit card. Jumper settings are documented in CHAPTER 3.
SETTING JUMPERS AND SWITCH OPTIONS of the Power System Installation
Instructions (IM582127000).
11) Slide the replacement circuit card into the mounting position inside the
distribution cabinet, and secure with the screws removed from the old circuit
card.
12) Plug all connectors removed from the old circuit card into the same position on
the replacement circuit card.
Danger: In the next step, external alarm wiring may be energized from an
external source. DO NOT allow bare wire ends to contact any
grounded or energized object.
13) Reconnect the external wiring to the correct terminals on the customer
connection terminal block. First remove the electrical tape that was applied to
the bare wire end in a previous step. DO NOT allow the bare wire end to contact
any grounded or energized object. After securing the wire, gently tug on the wire
to ensure that it cannot be pulled out of the terminal block. Repeat for each wire
to be reconnected.
14) Remove the grounding wrist strap.
15) Reinstall the top and front panels that cover the circuit cards at the bottom of the
distribution cabinet.
16) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
17) Enable the external alarms, or notify appropriate personnel that this procedure is
finished.
18) Ensure that there are no local or remote alarms active on the system.
Page 38
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
J1, J2, J3, J4
Distribution Panels FA Inputs
J8 (Main Bay Only)
Selects to power Controller
from “Battery Power” or not.
J1
No
Battery Battery
Pwr Pwr
J2
RS485 Connection
TB2 1A: RS485+
TB2 2A: RS485-
1
2
3
J3
1B 2B 3B
TB2
J10 (Main Bay Only)
Battery Monitoring External / Internal
(see TB1-4 and TB1-5 for
external monitoring points)
J10
J8
J8
Shorting Jumper
J4
1A 2A 3A
RS232 Connection
TB2 1B: CGND
TB2 2B: TXD232
TB2 3B:RXD232
7
8
9
External Internal
1
TB1
1
2
3
J5
5
TP1
TP2
TP3
7
8
9
TP4
Shorting Jumper
J10
J5
CAN
TB1-1: Battery Tray FA
TB1-2: External Battery FA
TB1-3: External System FA
TB1-4: External Battery Monitoring (-)
TB1-5: External Battery Monitoring (+)
TP1 (+) and TP2 (-)
Bay Voltage
Monitoring
TP3 (+) and TP4 (-)
Bay Load
Shunt Monitoring
TB1
TB1-2, TB1-3, TB1-4, TB1-5 Main Bay Only.
Wire Size Capacity: 22-12 AWG.
Recommended Torque: 3.0 in-lbs.
FA Signals: Battery applied to the terminal
turns in an alarm.
Figure 4-9
System Interface Circuit Card Connector Locations
Chapter 4. Troubleshooting and Repair
Page 39
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
SM-DU Circuit Card Replacement (Supplemental Bays Only)
Procedure
1) Performing this procedure may activate external alarms. Do one of the following.
If possible, disable these alarms. If these alarms cannot be easily disabled,
notify the appropriate personnel to disregard any future alarms associated with
this system while the procedure is being performed.
Danger: Performing the next steps exposes service personnel to battery
potential. Exercise extreme caution not to inadvertently contact or
have any tool inadvertently contact any energized electrical
termination.
2) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
Warning: Damage to the circuit card may result if the next step is not followed.
3) Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.
4) Remove the top and front panels to access the circuit cards at the bottom of the
distribution cabinet. See Figure 4-10.
5) Remove connectors J1, J2, and J3 from the circuit card.
6) Remove the screws securing the circuit card and remove the circuit card from the
distribution cabinet.
7) In this step, ensure you do not intermix the old and replacement circuit cards.
Set the switches on the replacement circuit card to the same setting as the old
circuit card. Switch settings are documented in CHAPTER 3. SETTING
JUMPERS AND SWITCH OPTIONS of the Power System Installation
Instructions (IM582127000).
8) Slide the replacement circuit card into the mounting position inside the
distribution cabinet, and secure with the screws removed from the old circuit
card.
9) Plug connectors J1, J2, and J3 into the circuit card.
10) Reinstall the top and front panels that cover the circuit cards at the bottom of the
distribution cabinet.
11) Remove the grounding wrist strap.
12) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
13) Temporarily remove then re-insert the ACU+. Wait for the ACU+ to initialize.
14) Enable the external alarms, or notify appropriate personnel that this procedure is
finished.
15) Ensure that there are no local or remote alarms active on the system.
Page 40
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
SM-DU
SM-DU
Figure 4-10
SM-DU Circuit Card Replacement (Supplemental Bays Only)
Chapter 4. Troubleshooting and Repair
Page 41
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
IB2 (ACU+ Interface Board) and Optional EIB (ACU+
Extended Interface Board) Replacement (Main Bay Only)
Procedure
1) Performing this procedure may activate external alarms. Do one of the following.
If possible, disable these alarms. If these alarms cannot be easily disabled,
notify the appropriate personnel to disregard any future alarms associated with
this system while the procedure is being performed.
Danger: Performing the next steps exposes service personnel to battery
potential. Exercise extreme caution not to inadvertently contact or
have any tool inadvertently contact any energized electrical
termination.
2) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
Warning: Damage to the circuit card may result if the next step is not followed.
3) Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.
4) Carefully label the wires connected to the customer connection terminal blocks
on the circuit card. These wires must be connected to the same terminals on the
replacement circuit card. Refer to Figure 4-11 or Figure 4-12.
5) Carefully label the connectors plugged into the circuit card. These connectors
must be plugged into the same connectors on the replacement circuit card.
Refer to Figure 4-11 or Figure 4-12.
Danger: In the next step, external wiring may be energized from an external
source. DO NOT allow bare wire ends to contact any grounded or
energized object.
6) Remove the external wiring from the customer connection terminal blocks. DO
NOT allow the bare wire end to contact any grounded or energized object.
Isolate the wire end with electrical tape. Repeat for each wire to be removed.
7) Unplug all connectors plugged into the circuit card.
8) Remove the circuit card by removing the bracket the circuit card is mounted to.
Remove the circuit card from the bracket.
9) In this step, ensure you do not intermix the old and replacement circuit cards.
Set the switch on the replacement circuit card to the same setting as the old
circuit card. Switch settings are documented in CHAPTER 3. SETTING
JUMPERS AND SWITCH OPTIONS of the Power System Installation
Instructions (IM582127000).
10) Secure the replacement circuit card to the bracket, and re-install the circuit card
and bracket into the distribution cabinet.
11) Plug all connectors removed from the old circuit card into the same position on
the replacement circuit card.
Danger: In the next step, external alarm wiring may be energized from an
external source. DO NOT allow bare wire ends to contact any
grounded or energized object.
12) Reconnect the external wiring to the correct terminals on the customer
connection terminal block. First remove the electrical tape that was applied to
the bare wire end in a previous step. DO NOT allow the bare wire end to contact
any grounded or energized object. After securing the wire, gently tug on the wire
Page 42
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
to ensure that it cannot be pulled out of the terminal block. Repeat for each wire
to be reconnected.
13) Remove the grounding wrist strap.
14) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
15) Enable the external alarms, or notify appropriate personnel that this procedure is
finished.
IB2 Board (Top View)
Connector
to ACU+
2
8 7 6 5 4 3 2 1
4
1
6
3
2
5
4
1
6
3
2
5
4
1
6
3
SW1
RELAY
4
4
4
4
6
8
2
6
6
2
6
4
2
6
2
2
5
1
3
5
1
3
5
1
3
5
1
NO C NC NO C NC NO C NC NO C NC
3
5
*
NO C NC NO C NC NO C NC NO C NC
1
3
5
7
Relay Output Terminal Blocks
J9
J8
J7
J6
Digital Input Terminal Blocks
J5
J4
J3
-
+
J11
J12
IB2 Board Assembly
J2
IB2 TEMP
PROBE 2
IB2 TEMP
PROBRE 1
16) Ensure that there are no local or remote alarms active on the system.
J3-J9:
Wire Size Capacity: 16-26 AWG.
Recommended Torque: 2.2 in-lbs.
Figure 4-11
IB2 (ACU+ Interface Board) Connector Locations
Chapter 4. Troubleshooting and Repair
Page 43
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Optional EIB Interface Board Assembly
J8
J9
Optional EIB Interface Board
(Top View)
J5
J6
J7
SW1
J2
J3
J4
J5-J9
Wire Size Capacity: 16-26 AWG.
Recommended Torque: 2.2 in-lbs.
Figure 4-12
EIB (ACU+ Extended Interface Board) Connector Locations
Page 44
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
SM-DU+ and Shunt Interface Assembly Replacement
Procedure
1) Performing this procedure may activate external alarms. Do one of the following.
If possible, disable these alarms. If these alarms cannot be easily disabled,
notify the appropriate personnel to disregard any future alarms associated with
this system while the procedure is being performed.
Danger: Performing the next steps exposes service personnel to battery
potential. Exercise extreme caution not to inadvertently contact or
have any tool inadvertently contact any energized electrical
termination.
2) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
Warning: Damage to the circuit card may result if the next step is not followed.
3) Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.
4) Carefully label the wires connected to the shunt input terminal blocks on circuit
card. These wires must be connected to the same terminals on the replacement
circuit card. Refer to Figure 4-13.
5) Carefully label the connectors plugged into the circuit card. These connectors
must be plugged into the same connectors on the replacement circuit card.
Refer to Figure 4-13.
Danger: In the next step, external wiring may be energized from an external
source. DO NOT allow bare wire ends to contact any grounded or
energized object.
6) Remove the external wiring from the shunt input terminal blocks. DO NOT allow
the bare wire end to contact any grounded or energized object. Isolate the wire
end with electrical tape. Repeat for each wire to be removed.
7) Unplug all connectors plugged into the circuit card.
8) Remove the screw securing the SM-DU+ and Shunt Interface Assembly to the
bottom of the distribution cabinet, and remove the assembly.
9) SM-DU+: In this step, ensure you do not intermix the old and replacement circuit
cards. Set the switches on the replacement circuit card to the same settings as
the old circuit card. Switch settings are documented in CHAPTER 3. SETTING
JUMPERS AND SWITCH OPTIONS of the Power System Installation
Instructions (IM582127000).
10) Slide the replacement SM-DU+ and Shunt Interface Assembly into the mounting
position inside the distribution cabinet, and secure with the screw removed from
the old assembly.
11) Plug all connectors removed from the old circuit card into the same position on
the replacement circuit card.
Danger: In the next step, external alarm wiring may be energized from an
external source. DO NOT allow bare wire ends to contact any
grounded or energized object.
12) Reconnect the external wiring to the correct terminals on the shunt input terminal
blocks. First remove the electrical tape that was applied to the bare wire end in a
previous step. DO NOT allow the bare wire end to contact any grounded or
energized object. After securing the wire, gently tug on the wire to ensure that it
Chapter 4. Troubleshooting and Repair
Page 45
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
cannot be pulled out of the terminal block. Repeat for each wire to be
reconnected.
13) Remove the grounding wrist strap.
14) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
15) Enable the external alarms, or notify appropriate personnel that this procedure is
finished.
16) Ensure that there are no local or remote alarms active on the system.
Page 46
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
SM-DU+ and
Shunt Interface Board
TB1 - TB2
Wire Size Capacity: 16-26 AWG.
Recommended Torque: 2.2 in-lbs.
RS 232
RS485
RS485
J5
J3
can
TB2
J4
J4A
Red Indicator
Yellow Indicator
Green Indicator
SW2
SW1
1B
1A
pow er
J1
J7
SHUNT
J1
J8
SHUNT
TB1
J6
FUSE
J2
ON
Shunt Interface Board
OFF
12345678 12345678
SM-DU+
Figure 4-13
SM-DU+ and Shunt Interface Assembly Connector Locations
Chapter 4. Troubleshooting and Repair
Page 47
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Optional LVD Driver and LVD Driver Lite Circuit Card Replacement
Procedure
1) Performing this procedure may activate external alarms. Do one of the following.
If possible, disable these alarms. If these alarms cannot be easily disabled,
notify the appropriate personnel to disregard any future alarms associated with
this system while the procedure is being performed.
Danger: Performing the next steps exposes service personnel to battery
potential. Exercise extreme caution not to inadvertently contact or
have any tool inadvertently contact any energized electrical
termination.
2) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
Warning: Damage to the circuit card may result if the next step is not followed.
3) Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.
4) If any of the low voltage disconnect contactors is open and it is desired to be
closed, push the LVD Inhibit Switch located on the circuit card installed in the
main bay to the UP position momentarily and then leave the switch in the middle
(OFF) position.
5) Remove the top and front panels to access the circuit cards at the bottom of the
distribution cabinet.
6) Carefully label the connectors plugged into the circuit card. These connectors
must be plugged into the same connectors on the replacement circuit card.
Refer to Figure 4-14 or Figure 4-15.
7) Unplug all connectors plugged into the circuit card.
8) Remove the screws securing the circuit card and remove the circuit card from the
distribution cabinet.
9) Slide the replacement circuit card into the mounting position inside the
distribution cabinet, and secure with the screws removed from the old circuit
card.
10) Ensure that the LVD Inhibit Switch is in the middle (OFF) position.
11) Plug all connectors removed from the old circuit card into the same position on
the replacement circuit card.
12) Push the LVD Inhibit Switch to the down (ON) position.
13) Remove the grounding wrist strap.
14) Reinstall the top and front panels that cover the circuit cards at the bottom of the
distribution cabinet.
15) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
16) Enable the external alarms, or notify appropriate personnel that this procedure is
finished.
17) Ensure that there are no local or remote alarms active on the system.
Page 48
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
J5
J6
J3
UM582127000
Issue AC, January 2, 2013
J4
J2
J1
J1, J2, J3
To LVLD contactor, uses ACU+
LVD1 control setting (Level 1).
J7
J4, J5, J6
To LVLD contactor, uses ACU+
LVD2 control setting (Level 2).
S1
DO NOT change a Low Voltage
Load Disconnect contactor to
LVD Control Level 2 (LVD2) if
the system is furnished with a
Low Voltage Battery Disconnect
contactor.
J7
To LVBD contactor, uses ACU+
LVD2 control setting (Level 2).
Notes:
1. Connects up to (4) LVLD
and (1) LVBD contactors.
2. Switch and indicator located
on circuit card installed in
Main Bay only.
Figure 4-14
Optional LVD Driver Circuit Card Connector Locations
Chapter 4. Troubleshooting and Repair
Page 49
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
DO NOT change a Low Voltage
Load Disconnect contactor to
LVD Control Level 2 (LVD2) if
the system is furnished with a
Low Voltage Battery Disconnect
contactor.
J1
To LVLD contactor, uses ACU+
LVD1 control setting (Level 1).
J3
To LVLD contactor, uses ACU+
LVD2 control setting (Level 2).
J3
J1
J2
To LVBD contactor, uses ACU+
LVD2 control setting (Level 2).
Can only be used if it is contained
in a List 21 (1-row) cabinet.
Notes:
1. Connects up to (2) LVD
contactors rated at 600A or less.
2. Only one (1) contactor per level
can be accommodated. J2 and J3
are on Level 2, only one (1) of these
connectors can be used at a time.
3. Switch and indicator located
on circuit card installed in
Main Bay only.
J2
S1
Figure 4-15
Optional LVD Driver Lite Circuit Card Connector Locations
Page 50
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Optional Manual Battery Disconnect Circuit Card Replacement
Procedure
1) Performing this procedure may activate external alarms. Do one of the following.
If possible, disable these alarms. If these alarms cannot be easily disabled,
notify the appropriate personnel to disregard any future alarms associated with
this system while the procedure is being performed.
Danger: Performing the next steps exposes service personnel to battery
potential. Exercise extreme caution not to inadvertently contact or
have any tool inadvertently contact any energized electrical
termination.
2) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
Warning: Damage to the circuit card may result if the next step is not followed.
3) Connect an approved grounding strap to your wrist. Attach the other end to a
suitable ground.
4) Remove the top and front panels to access the circuit cards at the bottom of the
distribution cabinet.
5) Carefully label the connectors plugged into the circuit card. These connectors
must be plugged into the same connectors on the replacement circuit card.
Refer to Figure 4-16.
6) Unplug all connectors plugged into the circuit card.
7) Remove the screws securing the circuit card and remove the circuit card from the
distribution cabinet.
8) Place the replacement circuit card into the mounting position inside the
distribution cabinet, and secure with the screws removed from the old circuit
card.
9) Plug all connectors removed from the old circuit card into the same position on
the replacement circuit card.
10) Remove the grounding wrist strap.
11) Reinstall the top and front panels that cover the circuit cards at the bottom of the
distribution cabinet.
12) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
13) Enable the external alarms, or notify appropriate personnel that this procedure is
finished.
14) Ensure that there are no local or remote alarms active on the system.
Chapter 4. Troubleshooting and Repair
Page 51
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
J2
J1
Figure 4-16
Optional Manual Battery Disconnect Circuit Card Connector Locations
Page 52
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Replacing a Distribution Panel
Danger: Performing this procedure exposes service personnel to battery potential.
Exercise extreme caution not to inadvertently contact or have any tool
inadvertently contact any energized electrical termination.
Procedure
Note: Refer to Figure 4-17 as this procedure is performed.
Removing the Distribution Panel
1) Open the distribution cabinet’s front door by turning the latch in the
counterclockwise position.
2) Remove the plastic shield covering the circuit breakers or fuseholders on the
panel to be removed by loosening the screws holding the shield and sliding the
shield upwards.
3) Disconnect all load or battery wiring from the circuit breaker or fuse positions.
4) On panels equipped with a ground busbar, remove all load return or battery
return wiring from the ground busbar.
5) On panels equipped with shunts, label the shunt leads then remove them from
the panel.
6) Locate the in-line FA/CBA connector located near the back of the panel, and
separate the connector halves.
7) Refer to Figure 4-17 and remove the hardware securing the panel’s Ground
Busbar (if equipped) to the distribution cabinet’s busbar.
8) For load distribution panels, refer to Figure 4-17 and remove the hardware
securing the panel’s System Load Distribution busbar to the distribution cabinet’s
busbar.
9) For battery distribution panels, refer to Figure 4-17 and remove the hardware
securing the panel’s Battery Busbar to the distribution cabinet’s busbar.
10) For dual voltage load distribution panels, refer to Figure 4-17 and remove the
hardware securing the +24V jumper leads.
11) Refer to Figure 4-17 and remove the hardware securing the distribution panel to
the distribution cabinet. Remove the panel from the distribution cabinet.
Chapter 4. Troubleshooting and Repair
Page 53
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Installing the Distribution Panel
Note: In the following procedure, before making busbar-to-busbar connections, apply a
thin coating of electrical anti-oxidizing compound to the mating surfaces of the
busbars.
1) Orient the replacement distribution panel into distribution cabinet, checking to
ensure no wires are pinched. Replace the hardware securing the distribution
panel to the distribution cabinet (10-32 x 5/8” bolt, #10 flat washer, 4-places).
2) For dual voltage load distribution panels, replace the hardware securing the
+24V jumper leads (1/4-20 bolt, 1/4” lock washer, 1/4” flat washer. Torque to 84
in-lbs).
3) For battery distribution panels, replace the hardware securing the panel’s
Battery Busbar to the distribution cabinet’s busbar (3/8-16 x 1-1/4” bolt, 3/8”
Belleville lock washer, 3/8” hardened flat washer, 2-places. Torque to 180
in-lbs.)
4) For load distribution panels, replace the hardware securing the panel’s System
Load Distribution busbar to the distribution cabinet’s busbar (1/4-20 x 1” bolt, 1/4”
Belleville lock washer, 1/4” Belleville lock washer (concave side of Belleville lock
washers face each other), 1/4” hardened flat washer, 2-places. Torque to 60
in-lbs).
5) Replace the hardware securing the panel’s Ground Busbar (if equipped) to the
distribution cabinet’s busbar (1/4-20 x 1” bolt, 1/4” Belleville lock washer, 1/4”
Belleville lock washer (concave side of Belleville lock washers face each other),
1/4” hardened flat washer, 2-places. Torque to 60 in-lbs).
6) Locate the in-line FA/CBA connector located near the back of the panel, and plug
it into the mating connector half in the distribution cabinet.
7) On panels equipped with shunts, reconnect the shunt leads.
Warning: In the next step, observe correct polarity; otherwise equipment
damage will result.
8) On panels equipped with a ground busbar, reconnect the load return or battery
return wiring to the ground busbar.
9) Reconnect the load or battery wiring to the circuit breaker or fuse positions.
10) Transfer the plug-in circuit breakers or fuses from the old panel to the
replacement panel.
11) Replace the plastic shield covering the circuit breakers or fuseholders on the
replacement panel.
12) Verify no Circuit Breaker/Fuse Alarms are active.
13) Close the distribution cabinet’s front door. Turn the latch clockwise to secure the
door.
Page 54
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Battery Busbar
Hardware
Ground Busbar
Hardware
Battery
Distribution
Panel
Distribution Panel
Hardware
Distribution Panel
Hardware
Load
Distribution
Panel
Ground Busbar
Hardware
System Load
Distribution Busbar
Hardware
Front
Front
Components removed in illustration for clarity only.
List DA Dual Voltage
Distribution Panel
(Lists DB, DC, and DD similar.)
/+24/ jumpers.
Assembly order is: lug, 1/4" flat washer,
1/4" lock washer, 1/4-20 bolt.
Torque to 84 in-lbs.
Figure 4-17
Replacing a Distribution Panel
Chapter 4. Troubleshooting and Repair
Page 55
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Replacing a Battery or Load Disconnect Contactor
Danger: All sources of AC and DC power must be completely disconnected from
this power system before performing this procedure. Use a voltmeter to
verify no DC voltage is present on the system busbars before proceeding.
Note: In the following procedure, before making busbar-to-busbar connections, apply a
thin coating of electrical anti-oxidizing compound to the mating surfaces of the
busbars.
Procedure
Note: Refer to Figure 4-18, Figure 4-19, Figure 4-20, or Figure 4-21 as this
procedure is performed.
Removing the Contactor
1) Verify all AC and DC power sources are disconnected from the power system.
2) For the 1-row distribution cabinet, the contactor can be accessed from the top
of the distribution cabinet. For the 2, 3, or 4-row distribution cabinet, the
contactor can be accessed from the rear (and top) of the distribution cabinet.
3) For the 2, 3, or 4-row distribution cabinet, remove the distribution cabinet’s
rear access panel(s).
4) Disconnect the wiring to the contactor by unplugging the quick disconnects.
5) Note the orientation of the contactor to ensure the replacement is installed the
same way. Unbolt the contactor (4-places) and remove. Save all hardware.
Installing the Replacement Contactor
1) Position the replacement contactor oriented the same way as the old.
2) Secure the contactor with the hardware removed above. Refer to Figure 4-18,
Figure 4-19, Figure 4-20, or Figure 4-21 for hardware build-up and recommended
torque.
3) Replace the wiring to the contactor by plugging-in the quick disconnects. Refer
to Figure 4-18, Figure 4-19, Figure 4-20, or Figure 4-21.
4) For the 2, 3, or 4-row distribution cabinet, replace the distribution cabinet’s rear
access panel(s).
Restarting the Power System
1) Reconnect the AC and DC power sources to the power system.
2) Start the power system. Refer to the separate Installation Instructions
(IM582127000) for a startup procedure.
3) Verify no alarms are active.
Page 56
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
Battery
Disconnect
Contactor
5/16-18 x 1” Bolt
5/16" Belleville Lock Washer
5/16" Belleville Lock Washer
(concave side of Belleville
Lock Washers face each other)
5/16" Hardened Flat Washer
(4 places)
Torque to 100 in-lbs.
Apply electrical anti-oxidizing
compound to busbar mating surfaces.
Components removed in
illustration for clarity only.
Front
Contactor styles vary
between manufacturer’s.
Brown Wire
Brown/White Wire
Red/White Wire
White/Black Wire
Brown Wire
Brown/White Wire
White/Black Wire
Red/White Wire
Figure 4-18
Replacing a Battery Disconnect Contactor
in a 1-Row Distribution Cabinet
Chapter 4. Troubleshooting and Repair
Page 57
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
1/2-13 x 1-1/4” Bolt
1/2" Belleville Lock Washer
1/2" Belleville Lock Washer
(concave side of Belleville
Lock Washers face each other)
1/2" Hardened Flat Washer
(4 places)
Torque to 500 in-lbs.
Apply electrical anti-oxidizing
compound to busbar mating surfaces.
Battery
Disconnect
Contactor
Front
Shown being removed from front
for clarity only. Removal is from rear.
Components removed in
illustration for clarity only.
Brown/White Wire
Brown Wire
2-row Distribution Cabinet
shown, 3 or 4-row cabinet similar.
Red/White
Wire
White/Black
Wire
Figure 4-19
Replacing a Battery Disconnect Contactor
in a 2, 3, or 4-Row Distribution Cabinet
Page 58
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
5/16-18 x 1” Bolt
5/16" Belleville Lock Washer
5/16" Belleville Lock Washer
(concave side of Belleville
Lock Washers face each other)
5/16" Hardened Flat Washer
(4 places)
Torque to 100 in-lbs.
Load
Disconnect
Contactor
Apply electrical anti-oxidizing
compound to busbar
mating surfaces.
Components removed in
illustration for clarity only.
Front
Contactor styles vary
between manufacturer’s.
Violet/White Wire
Violet Wire
Red Wire
Black Wire
Violet/White Wire
Violet Wire
Black Wire
Red Wire
Figure 4-20
Replacing a Load Disconnect Contactor
in a 1-Row Distribution Cabinet
Chapter 4. Troubleshooting and Repair
Page 59
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
Components removed in
illustration for clarity only.
Load Disconnect
Contactor
5/16-18 Nut
5/16" Belleville Lock Washer
5/16" Belleville Lock Washer
(concave side of Belleville
Lock Washers face each other)
5/16" Hardened Flat Washer
(4 places)
Torque to 100 in-lbs.
Apply electrical anti-oxidizing
compound to busbar
mating surfaces.
Front
2-row Distribution Cabinet
shown, 3 or 4-row cabinet similar.
Contactor styles vary
between manufacturer’s.
Violet/White Wire
Violet Wire
Red Wire
Black Wire
Violet/White Wire
Violet Wire
Black Wire
Red Wire
Figure 4-21
Replacing a Load Disconnect Contactor
in a 2, 3, or 4-Row Distribution Cabinet
Page 60
Chapter 4. Troubleshooting and Repair
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
User Instructions
Spec. No. 582127000 (Model 721NPBB)
UM582127000
Issue AC, January 2, 2013
This Page Left Intentionally Blank
Chapter 4. Troubleshooting and Repair
Page 61
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
UM582127000
Issue AC, January 2, 2013
User Instructions
Spec. No. 582127000 (Model 721NPBB)
REVISION RECORD
Issue
Change
Number
(ECO)
AA
LLP216539
AB
LLP217311
AC
LLP218149
Page 62
Description of Change
New
Battery Charge Current Limit Functionality added to Operating Procedures
chapter.
Adding 588705300, R48-2000e3, and C48/24-1500. Removing 588249700.
Revision Record
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
NetPerform™ Optimization Services
At Emerson Network Power, we understand the importance of reliable equipment – it’s critical to both your business and your
bottom line. That is why we offer a wide array of services to meet all of your network infrastructure needs.
Customer Service
[1,2]
Customer Support Center
Account Management
[2]
Spare Parts
DC Power Depot Repair
Technical Support
[1]
[2]
For More Information
To learn more about service offerings from Emerson Network Power, please contact your sales representative,
call 1-800-800-1280 option 7, email ES.Services@Emerson.com or visit EmersonNetworkPower.com/EnergySystems.