Owner`s manual | Emerson BACNET IP Power Supply User Manual

PRÉCAUTION: Danger d’explosion si les piles sont remplacées de facon incorrect. Remplacer
les piles seulement par le méme type de pile ou l’équivalent.
SmartSet ® Clock Radio,
With Auto-Time Setting System,
Thank you for purchasing this Emerson SmartSet ® Dual Alarm Clock Radio.
This clock radio uses Emerson's patented SmartSet ® Automatic Time Setting System.
The first time you connect this clock radio to your AC outlet, and aftere very power
interruption, within seconds the clock will automatically set itself t o t h e c o r r e c t Ye a r,
Month, Date, Day, and Time. In addition all changes from Standard Time to Daylight
Saving Time, and back to Standard Time, are made automatically.
There are dual alarms that can be set and used independently, and both of the alarms
can be programmed for everyday operation, weekdays only, or weekends only.
There is a long life lithium battery installed in this clock radio when you buy it.
This battery can maintain the time and alarm settings for 3 to 5 years, or even longer.
We have taken every precaution to make sure this radio was in perfect working order
when it left our factory. If you encounter any problems with the set up or operation of this
item, please call the Emerson Consumer Products Corp.,
Customer Service Hotline, toll free, at 1 -800-898-9020.
Dual Alarms,
Date Display
PREPARATION FOR USE
• Operate controls and switches as
described in the manual.
• Before turning on the power, make
certain that the AC adapter is
properly installed.
• When moving the set, be sure to first
disconnect the AC adapter.
• Av o i d i n s t a l l i n g t h i s u n i t i n p l a c e s
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
(U.S. Patent No. 6,567,344)
To see the correct date at any time, depress the MONTH/DATE button. The display
Changes from time to Month and Date (MM/DD).
For example, May 21st will appear as “ 5.21” .
When you release the MONTH/DATE button
the display returns to the correct time.
Front Panel
2
1
6
5
IMPORTANT NOTES
PLL AM/FM Radio
Hold the TIME ZONE button and then press either the SET + (up) or – (down)
buttons until your own time zone appears on the display, then release the buttons.
The clock display will change to the correct time in the time zone you selected.
The clock will always return to the correct time in the zone you selected after every
power interruption.
If you move to a different time zone, simply change the default zone display to the
new zone and the SmartSet ® will remember that setting for you.
This radio should be connected to an AC outlet that
is always 'live'. Do not connect it to an outlet that is
controlled by a wall switch. When the power to the
radio is interrupted, the built in lithium battery takes
over to maintain the time and alarm settings. To
maximize the life of the lithium battery keep the radio
connected to a 'live' AC outlet at all times.
1
1
2
2
52
AM
3
kHz
MHz
7
21
Top Panel
8
13
9
14
10
18
19
15
12
17
16
11
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
i n t e r f e r e n c e t o r a d i o c o m m u n i c a t i o n s . H o w e v e r, t h e r e i s n o g u a r a n t e e t h a t
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/T V technician for help.
OWNER'S MANUAL
CKS1800
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence
of uninsulated 'dangerous voltage'
within the product's enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
WARNING:TOREDUCE THE RISK
OF ELECTRIC SHOOK DO NOT
REMOVE COVER (OR BACK),NO
USER SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
AVIS:RISQUE DE CHOC
ELECTRIQUE-NE PAS OUVRIR
The exclamation point within
an equilateral triangle is intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying the appliance.
2
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
PREPARATION FOR USE
Unpacking And Set Up
•
This is CLASS II apparatus with double insulation, and no protective earth provided.
The Caution Marking located at the bottom enclosure of the apparatus.
•
IMPORTANT SAFETY INSTRUCTIONS
•
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
11.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
12.) The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
13.) Mains plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from the
mains completely, the mains plug should be disconnected from the mains
socket outlet completely.
14.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
1
•
•
Remove the radio from the carton and remove all packing material from the
radio. We suggest that you save the packing material, if possible, in the unlikely
event that your radio ever needs to be returned for service. The original carton
and packing material is the only safe way to pack your radio to protect it from
damage in transit.
Remove any descriptive labels or stickers on the front or top of the cabinet. Do
not remove any labels or stickers from the back or bottom of the cabinet.
Note the serial number on the bottom of your radio and write this number in the
space provided on the Warranty page of this manual.
Place your radio on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
Unwind the Line cord connecting the AC adapter and extend it to its full length.
The FM antenna is built in to this cord. It must be fully extended to provide the
best FM reception.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
Power Source
This radio is designed to operate on normal 120V 60Hz AC power only. Do not
attempt to operate the radio on any other power source. You could cause damage
to the radio that is not covered by your warranty.
3
' Day of Week' Display
If the radio or buzzer is 'Off ', to view the correct 'Day of Week', depress the
W E E K b u t t o n . T h e d i s p l a y w i l l c h a n g e f r o m Ti m e t o “ D a y o f We e k ” . W h e n
you release the WEEK button the display returns to the correct Time.
I f t h e r a d i o o r b u z z e r i s ' O n ' , t o v i e w t h e c o r r e c t ' D a y o f We e k ' , p r e s s t h e
RADIO ON/OFF Button first to stop the radio or buzzer,
then depress the WEEK button, display will change
from Time to 'Day of Week'. When you release the
WEEK button the display returns to the correct Time.
Note: From d1,d2 to d7 stand for from Monday ,Tuesday to Sunday separately.
Daylight Saving and Leap Year Adjustments
4
Visit our web site at www.emersonradio.com
Year Display
To see the correct year, depress the MONTH/DATE and TIME buttons together.
The display changes from time to year.
When you release the MONTH/DATE and
TIME buttons the display returns to the
correct time.
A l l D a y l i g h t S a v i n g a n d L e a p Ye a r a d j u s t m e n t s a r e m a d e a u t o m a t i c a l l y b y
the SmartSet ® internal computer as follows:
• Start of Daylight Saving Time:
At "2:00 AM" on the 2nd Sunday in March, the clock will automatically
advance to "3:00 AM".
• End of Daylight Saving Time:
At '3:00 AM' on the 1st Sunday in November, the clock will automatically
reset to "2:00 AM".
• Leap Year:
At "12:00 Midnight" on February 28th, the calendar display will change
to "2.29".
20
6
4
1.) 1 (Alarm 1 'Buzzer') Indicator.
13.) Speaker (Back Cabinet).
2.) 1 (Alarm 1 'Radio') Indicator.
14.) ALARM 1 Setting / VOLUME + Button.
3.) AM Indicator.
15.) ALARM 2 Setting / VOLUME - Button.
4.) Time/Date Display.
16.) WEEK MODE Button. (Weekdays l
5.) 2 (Alarm 2 'Buzzer') Indicator.
Weekends l Everyday Alarm)
6.) 2 (Alarm 2 'Radio') Indicator.
17.) SET - / TUNE - Button.
7.)
LOW BATT. Indicator.
18.) SET + / TUNE + Button.
8.) AC adapter (Back Cabinet).
19.)
RADIO ON/OFF Button.
9.) MONTH/DATE Setting / STORE
20.) SNOOZE / SLEEP OFF / DIMMER
Station Button.
Button.
10.) TIME Setting / BAND Select Button.
21.) Back Up Battery Compartment
11.) TIME ZONE / MEMORY Button.
(Bottom Cabinet).
12.) SLEEP Button (Sleep To Music Timer).
Note: For buttons displayed with additional INVERSED font or icons,
they have multiple function at different operation mode. Generally, the
functions displayed in INVERSED font are for operation when Radio is ON.
OPERATING INSTRUCTIONS
Setting The Time, The First Time
IMPORTANT: The first time you connect your new SmartSet® clock radio to the
AC outlet the internal computer will automatically set the time correctly for the
Eastern Time Zone, which is the initial default setting. The display will scan for a
few seconds and then show the correct Day and Time in the Eastern zone. If you
live in the Eastern Time zone, there's nothing else to do. Your clock is set correctly
and running.
If you do not live in the Eastern Time zone you must change the default zone
display to your own zone. You only do this one time and the Smart Set® will remember
the new default zone setting and will always return to that setting after a power
interruption.
There are 7 time zones programmed into your Smart Set ® clock radio as follows :
ZONE 1 — Atlantic Time
ZONE 2 — Eastern Time (Default Setting)
ZONE 3 — Central Time
ZONE 4 — Mountain Time
ZONE 5 — Pacific Time
ZONE 6 — Yukon Time
ZONE 7 — Hawaiian Time
To c h a n g e t h e d e f a u l t t i m e z o n e d i s p l a y,
depress the TIME ZONE button. The number
"2" will appear on the display indicating that the
default zone is ZONE 2, Eastern Time.
.
5
Manual Time Adjustments
Some people like to set their clocks 5 to 10 minutes fast to make sure that they will
always be on time. Even though the SmartSet ® sets the time by itself, you still have
the option of adjusting the time manually if you wish.
To manually adjust the time display depress and hold the TIME button, and press
either the SET + or - buttons to adjust the time display ahead or back as desired.
Each press of the SET + or - buttons will change the display by one minute. If you
hold the SET + or - buttons the display will continue to change. The display will
change slowly at first, one minute at a time. But if you continue holding the SET +or
- buttons the display will change rapidly.
NOTE: If you manually adjust the time, your new setting is entered into the
SmartSet ® memory. If the power is interrupted, the display will return to your
new setting, not the original setting, when the power is restored.
Adjusting The Wake Up Times
Your SmartSet ® clock radio has two separate alarms that can be set and used
independently. You may use the alarms to wake two people at different times, or
you may use one alarm for weekdays and the other for weekend wake up times.
The procedure for adjusting the wake up time is the same for both Alarm 1 and
Alarm 2.
1.) Depress and hold either the ALARM 1 or
AM
ALARM 2 setting button. The display will
change from the correct time to the Alarm 1
or Alarm 2 wake up time.
2.) While holding the ALARM 1or ALARM 2 setting button, depress either the
SET + or - button to move the display ahead or back to your desired wake up time.
3.) When the desired wake up time appears on the display, release the SET + or buttons.
NOTE: Be sure that you have set the wake up time correctly by observing the AM
indicator. If the AM indicator is 'On ' the wake up time is "AM". If the AM indicator is
'Off', the wake up time is "PM".
4.) When the desired wake up time (AM or PM) appears on the display, release the
ALARM 1 or ALARM 2 setting buttons.
Selecting The Alarm Week Mode
Your SmartSet ® clock radio allows you to select from among three different alarm
operation modes for either alarm. The alarm modes are:
• Everyday ― the alarm will turn on all 7 days.
• Weekdays only ― the alarm will only turn on Monday through Friday;
• Weekends only ― the alarm will only turn on Saturday and Sunday.
To check the Alarm Mode setting for Alarm1, depress the ALARM 1 setting button.
The display will show the Alarm 1 wake up time and the DAY OF WEEK indicators
will show you the alarm mode which is selected.
7
• it shows “1-7”, the Everyday mode is selected.
Radio And Buzzer Operation
Resetting The Clock After A Total Memory Loss
• If it shows “1-5”, the Weekdays only mode is selected .
You may also set one alarm for wake to RADIO and the other for wake to BUZZER.
Just press the ALARM 1 and ALARM 2 buttons to the desired status as shown on the
ALARM indicators.
If you do not change the built in lithium battery within a reasonable period of time
after you see the
warning indicator, the lithium battery may become exhausted
a n d w i l l n o l o n g e r b e a b l e t o s u p p l y b a c k u p p o w e r t o t h e S m a r t S e t®
internal computer. If the unit is disconnected from the AC outlet after the battery
is exhausted or if a power interruption occurs, the SmartSet ® memory will be lost
and the clock will need to be reset when the power is restored.
Be sure to install a fresh lithium battery before you reset the clock, otherwise the
clock will need to be reset each time the power is interrupted.
• If it shows “6-7”, the Weekends only mode is selected.
Snooze/Repeat Alarm
To change the Alarm Mode setting for Alarm 1, hold the ALARM 1 setting button
and press the ALARM MODE button until the DAY OF WEEK indicators show the
desired mode setting, Weekdays only, Weekends only, or Everyday operation.
Release the ALARM MODE and ALARM 1 setting buttons and the display will
return to the correct time.
Follow the same procedure to select the desired Alarm Mode for Alarm 2 if necessary.
Checking The Wake Up Times And Alarm Mode
Whenever you want to check the wake up time or the alarm mode settings, simply
press either the ALARM 1 or ALARM 2 setting buttons. The display will change
from correct time to wake up time and the DAY OF WEEK indicators will show you
the alarm mode which is currently selected.
Release the ALARM 1 or ALARM 2 setting buttons to return to correct time.
Listening To The Radio
1.) Press the RADIO ON/OFF button to turn the radio 'On'. The frequency of the
tuning frequency will show for a few seconds on the display.
2.) Set the BAND by pressing BAND button to AM or FM as the desired, it toggles
each time you press the BAND button.
3.) Set the VOLUME by pressing VOLUME + or VOLUME - to a level that is neither
too high nor too inaudible.
4.) Select your desired station with the TUNING control.
a) Press TUNE + or TUNE - slightly, the receiving frequency will increment or
decrement by one step.
b) Press and hold TUNE + or TUNE - for one second then release, Auto Station
Seeking will be engaged, the receiving frequency will increment or decrement
automatically until a station with acceptable reception is found.
5.) Adjust the VOLUME control to the desired setting.
6.) When you are finished listening, press the RADIO ON/OFF button to turn the
radio 'Off'.
Storing and Recalling Radio Station Memory
When you have a few favorite radio stations to listen to,you may like to save them,
and pick one out of them in a few seconds without needing to search it each time.
Our digital tuning technology allows you to do this easily by following the following
steps :
After the alarm turns 'On' in the morning you can SNOOZE/SLEEP OFF button on
the top cabinet for a few extra minutes sleep. The corresponding ALARM indicator
will flash. The alarm will stop for approximately 9 minutes and then comes 'On' again.
The Snooze operation may be repeated several times if desired but after one hour
the alarm will not come on again.
Sleep To Music Timer
You can program the sleep timer to play the radio for up to 90 minutes and then shut
'Off' automatically.
1 .) Press the SLEEP button.The display will briefly
show "10" and the radio will begin to play.
After 10 minutes countdown the radio will shut
off automatically. Each time you press the SLEEP button the sleep timer will
start at 10 minutes. This is the sleep timer default setting.
2.) To increase or decrease the amount of time that the radio will play before
shutting off, hold the SLEEP button and press either the SET + or - button to
change the display to the desired sleep time, up to a maximum of "90" minutes
or a minimum of "02" minutes.
NOTE: When you change the sleep timer from the 10 minute default setting to a
different setting, the new setting becomes the default setting. Whenever you
activate the sleep timer it will begin with your new default setting and count down
to zero from that point.
3.) To cancel the sleep timer before it counts down to '00' and shut the radio 'Off'
immediately, press the SNOOZE/SLEEP OFF Bar.
IMPORTANT: Remember that the station and volume settings you choose for
the Sleep To Music operation are the same settings you will hear if you set the
alarm for Wake To Radio the following morning.
DIMMER Control
The DIMMER control was set to High position at our factory.
If you find the clock display is too bright in a darkened room, set the Dimmer by
pressing SNOOZE / SLEEP OFF / DIMMER Button.
Changing The Lithium Battery
Like all batteries, eventually the built in lithium battery will need to be replaced. A
number of factors, such as, the length of time between the date the radio was
manufactured and the date you plugged it in for the first time determine the amount
of time before replacement. During this initial storage period, the lithium battery is
8
Storing to the Memory
1.) Make sure the radio is ON and the AM/FM band is selected.
2.) Tune to the desired station by the TUNING control as described.
3.) Press STORE , "P XX" blinks, indicating the memory location to store the
currently listening station.
4.) While "P XX" is blinking, press TUNE + or TUNE – can change the memory
location from 1 through 10. For e.g . , "P 03" means the current listening
station is about to stored into the 3rd location of the memory.
5.) After deciding the memory location, press STORE again, the currently listening
station is stored.
6.) The display will turn to the frequency of the stations afterwards, and after
a few seconds, the correct time shows.
Recalling Station from the Memory
1.) Make sure the radio is ON and the AM/FM band is selected.
2.) Press MEMORY , "P XX" shows on the display, and the station according to the
memory location is tuned.
3.) While "P XX" is showing on the display, press TUNE + or TUNE – can change
the memory location from 1 through 10, and the station stored in the location
is tuned once the location is changed to.
4.) The display will turn to the frequency of the stations afterwards, and after a
few seconds, the correct time shows.
Antenna Information
AM - The AM bar antenna is inside the cabinet. If AM reception is weak, change
the position of cabinet until the internal antenna picks up the strongest signal.
FM - The FM antenna is built in to the Line cord connecting the AC adapter.
If FM reception is weak try Varying the position and direction of the Line cord
until you find the strongest signal.
10
supplying power to the SmartSet ® computer memory. Once you plug the radio in,
your household outlet supplies the power, and the battery is not being used. A fresh
lithium battery can supply power to the SmartSet ® computer for at least 3 years even
if it is never connected to an AC power supply. If your clock radio was connected to
your AC supply within a few months after it was manufactured, and you experience
only the normal, nuisance type, short duration power interruptions, your battery may
last for up to 5 years or even longer.
When the battery power drops below a certain level, the
LOW BATT. indicator
will 'Flash'. When you see this indicator, you should change the battery as soon as
it is convenient for you to do so. To change the battery proceed as follows:
1.) Purchase a replacement 3V lithium battery wherever batteries are sold . The
battery type is CR2032 or equivalent.
2.) Remove the battery from its package so it is ready to install.
IMPORTANT: Leave the AC adapter connected to your AC outlet.
This will provide power to the SmartSet ® computer memory while the original
lithium battery is removed.
3.) Turn the radio face up and use a small screw driver to remove the screw securing
the battery holder to the cabinet.
4.) Remove the original battery from the holder and insert the new battery into the
holder the same way, observing the positive (+) direction. Slide the holder with
the new battery back into the slot in the cabinet.
BE CAREFUL NOT TO LOSE THIS SMALL SCREW !
5.) Replace the screw that secures the battery holder in the cabinet.
If the lithium battery is exhausted and you experience an interruption in the AC
power supply, the clock will reset itself to its initial default setting when the power is
restored.
The initial default setting is "12:00 AM, Sunday , January 1st (1. 1), 2012".
If you notice that the time on your SmartSet ® clock radio is completely incorrect,
and the DAY OF WEEK indicator is also wrong, press the MONTH/DATE button to
see the date.
If the date display is showing "1. 1 " (January 1st),
you probably experienced a total memory loss.
To reset the clock after a total memory loss, proceed
as follows:
1 .) Follow the instructions on page 10,11 and install a new CR2032 lithium battery
in the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself.
3.) Depress the MONTH/DATE and TIME buttons together. The display will change
from 'Time' to 'Year'.
W h i l e h o l d i n g i n t h e M O N T H / D AT E a n d T I M E b u t t o n s , p r e s s t h e S E T +
button to set the display to the correct year, then release the buttons.
4.) D e p r e s s t h e M O N T H / D AT E b u t t o n . T h e d i s p l a y w i l l c h a n g e f r o m ' Ti m e '
t o 'Month/Date' (MM/DD).
While holding in the MONTH/DATE button, press the SET + button to set the display
to the correct Month and Date. The DAY OF WEEK indicator will change automatically
as you adjust the Month/Date settings. When the correct Month and Date appear
on the display, release the buttons.
5.) Depress the TIME button and the SET + button to set the display to the correct
Time. Be sure to confirm that you have set the time correctly to 'AM' or 'PM'
by observing the AM indicator.
6.) After you set the Time, reconfirm that the Day, and Month/Date displays are
still correct. Make final adjustments if necessary.
The SmartSet ® clock memory is now reset and the new lithium battery will maintain
it for the next 5 to 8 years, depending on the number and duration of the power
outages you experience.
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts,
or replace the product at our discretion. For repair or replacement, pack your
unit in a padded box, enclose your check or money order payable to Emerson
Radio Corp. in the amount of $9.00 to cover shipping and handling costs, and
enclosed a copy of your proof of purchase. Send your unit to:
Emerson Returns Facility
11500 Philadelphia ST
Mira Loma, CA 91752
ATTN: Returns Department
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898N
The Serial Number can be found on the bottom cabinet. We suggest that you record
the Serial Number of your unit in the space below for future reference.
Model Number: CKS1800
Serial Number: _ ______ _ _ _ ______ _ _ _ ______ _ _ _ _
IMPORTANT NOTE
After resetting the clock, don't forget to reset your wake up times and alarm
mode settings, and sleep timer settings as well.
12
14
CARE AND MAINTENANCE
Care Of Cabinets
If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet becomes
smudged or dirty, clean it with a soft, slightly dampened cloth .
Never allow water or any liquid to get inside the cabinet. Never use any
abrasive cleaners or cleaning pads as these will damage the finish of your radio.
Lithium Battery Precautions
• D i s p o s e o f t h e o l d b a t t e r y p r o p e r l y. D o n o t l e a v e i t l y i n g a r o u n d w h e r e a
young child or pet could play with ,or swallow it. If the battery is swallowed.
contact a physician immediately.
• Battery may explode if mistreated. Do not attempt to recharge it or
disassemble it. Do not dispose of the old battery in a fire.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020 OR
1-800-695-0098 OR
E-MAIL TO: internet@emersonradio.com
Wake To BUZZER
NOTE: Alarm 1 and Alarm 2 have different buzzer sounds.
• Alarm l is a " Single beep" sound.
• Alarm 2 is a "Double beep" sound.
You will be able to tell which alarm is going off by the sound that it makes.
1 .) Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1 , Alarm 2, or both alarms.
2.) Press ALARM 1 or ALARM 2 button slightly, and repeat doing so if necessary,
until ALARM 1 "BUZZER" or ALARM 2 "BUZZER" indicator is lit on the display.
3.) At the selected wake up time the buzzer will sound. It will continue for one
hour and then shut off automatically.
4.) To stop the buzzer sooner, press the RADIO ON/OFF button. The buzzer will
stop but the alarm remains set and will turn the buzzer on again at the same
time on the following day (depending on the Alarm Mode setting).
5.) If you do not want the alarm to turn the radio on the following day, press the
appropriate ALARM button until the ALARM indicator on the display is OFF.
9
CR2032
POSITIVE(+)
6.) Turn the radio right side up and confirm that the
LOW BATT indicator is 'Off'.
7.) Save these instructions. You'll have to do this again five to eight years from Now!
WARNING: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
CKS1800- 305- 00
11
13
Printed in China
15
Download PDF

advertising