Emerson CKD2020 Clock Radio User Manual

Thank you for purchasing this Emerson Clock Radio.
We have taken every precaution to make sure this radio was in perfect working order
when it left our factory. If you encounter any problems with the set up or operation of
this item, please call the Emerson Consumer Products Corp., Customer Service
Hotline, toll free, at 1-800-898-9020.
IMPORTANT NOTES
AM/FM Radio, CD-R/RW Player
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters,on top of other stereo
equipment that radiates too much
heat,places lacking ventilation or dusty
areas,places subject to constant
vibration and/or humid or moist areas.
• Operate controls and switches as
described in the manual.
• Before turning on the power, make
certain that the power cord is properly
installed.
• When moving the set, be sure to first
disconnect the AC power cord.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged, to try to correct the
interference by one or more of the following measures:
with Dual Alarm Clock
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TVtechnician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
OWNER'S MANUAL
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CKD2020
Maintenance and care
1. Electronic products should never be
subjected to extreme temperatures
nor high humidity to ensure good
performance and a long life-time.The
clock radio should not be placed in
bathing areas, or around stoves and
radiators, etc. Always leave sufficient
space around the unit for ventilation.
2. If necessary, only clean the cabinet of
the unit with a soft dampened piece of
cloth, (be sure the AC power cord is
unplugged from the outlet). Never use
a polish or a strong detergent for
cleaning since this can damage the
finish o f t he c ab i n e t.
3. If the cabinet becomes dusty, wipe it
with a soft cloth. If the cabinet
becomes smudged or dirty, clean it
with a soft, silghtly dampened cloth.
Never allow water or any liquid to get
i nside t he c a b i n e t .
Never use any abrasive cleaners or
cleaning pads as these will damage
t he f inish of y our radio .
Power failure
When AC power is interrupted, both time
and alarm settings will be lost (unless
2 x AAA battery (not supplied) is installed)
after power is restored. The digital display
will blink to show power was interrupted.
You must reset time and alarm times.
Battery back up
To keep alarm and time of day settings in
memory during a brief power failure or
accidental removal of AC cord from mains
socket, install 2 x 1,5V “AAA” battery
(not supplied) into the Battery
Compartment on the underside of the unit.
Corrosion, oxidation, battery-leakage
and any other gradually acidic defect of
this nature will invalidate the guarantee.
LOCATION OF CONTROLS
8
6
9
10
11
1 2 3 4 5
7
12131415
17 18 19 20
16
21
23
24
PREPARATION FOR USE
Unpacking and Set Up
CAUTION
RI SK O F EL EC TR IC S HO CK
Remove the unit from the carton, and remove all the packing materials from the
unit.
DO N OT O PE N
22
WAR NI NG :S HO CK H AZ AR D. DO N OT O PE N
AVIS :R IS QU E DE C HO C ÉL EC TR IQ UE ,N E PAS OU VR IR
Save the carton and packing materials in case the unit ever needs to be returned
for service Using the original carton and packing materials is the only way to
safely repack the unit for shipment.
Remove any descriptive labels or stickers from the top or front of the unit. Do
not remove any labels from the back or bottom of the cabinet.
A
C
B
D
E
Remove any small strips of tape that may have been used to prevent the CD
door from opening in transit.
Note the Serial Number on the bottom of your radio and write this number in
the space provided on the Warranty page of this manual.
Press the CD OPEN button to open the CD door and remove the dummy CD
protection card from the CD compartment. Discard it and close the CD door.
G I J
F
Unwind the FM wire antenna on the back cabinet and extend it to its full length.
Visit our web site at www.emersonradio.com
2
WARNING
PLAYER MAINTENANCE
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
The lightning flash with arrowhead symbol,within an equilateral triangle is intended to
alert the user to the presence
of uninsulated‘dangerousvoltage’
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
4
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
WARNING:TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE PARTS INSIDE
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the liter ature accompanying the appliance.
The information Marking is located at the bottom enclosure of the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
Cleaning the Cabinet
IMPORTANT: Disconnect from Main Supply Before
cleaning.wipe with a soft cloth. If the cabinet is very
dirty, dampen the cloth with a weak solution of neutral
detergent and water, and then wipe clean.
Cleaning the Lens
A dirty lens may cause the sound to skip and, If the
lens is very dirty, the CD may not work. Open the
disc cover and clean the lens as follow:
Dry Dust Particles
Using a camera lens brush/blower, blow on the
lens couple times, then wipe it lightly with
the brush to remove dust. Then, blow on the lens
once more.
Finger prints
If the lens cannot be cleaned by using a brush/
blower use a dry cotton swab.
6
Unwind the AC power cord and extend it to its full length.
1. CLOCK ADJ button
Place the unit on a stable, level surface such as a table, desk, shelf, etc within
easy reach of an AC outlet, out of direct sunlight, and away from sources of
excessive heat, dust, moisture or humidity.
2. ALARM2 button
Protect Your Furniture
This model is equipped with non-skid rubber ‘feet’ to prevent the product from moving
when you operate the controls. These ‘feet’ are made from non-migrating rubber
material specially formulated to avoid leaving any marks or stains on your furniture.
However certain types of oil based furniture polishes, wood preservatives, or cleaning
sprays may cause the rubber 'feet’ to soften, and leave marks or a rubber residue on
the furniture. To prevent any damage to your furniture we strongly recommend that you
purchase small self-adhesive felt pads, available at hardware stores and home
improvement centers everywhere, and apply these pads to the bottom of the rubber
‘feet’ before you place the product on fine wooden furniture.
Power Sources
This system is designed to operate on 120V AC 60Hz house current only. Connecting
this system to any other power source may cause damage to the system and such
damage is not covered by your warranty.
16. 0.9"CLOCK display
A.ALARM 1 indicator
3. ALARM1 button
B.ALARM 2 indicator
4. VOLUME control
C.POWER indicator
5. AUX IN Jack
D.SLEEP indicator
6. SNOOZE button
E.RANDOM indicator
7. CD door
F.PROGRAM indicator
8. OPEN button
G.REPEAT indicator
9. ON/OFF button
I.SNOOZE indicator
10. FUNCTION (CD/AM/FM/
J.PM indicator
BUZZER) switch
17. PLAY/PAUSE button
11. TUNING control
18. SKIP I<< /MINUTE button
12. PROGRAM button
19. SKIP >>I/HOUR button
13. REPEAT/RANDOM button
20. STOP button
14. DISPLAY button
21. Speaker
15. SLEEP button
22. Battery Compartment
23. AC Power Cord
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
11.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
12.) The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
13.) Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from the
mains completely, the mains plug should be disconnected from the mains
socket outlet completely.
14.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
15.) The marking information is located at the bottom of apparatus.
CAUTION: Danger of explosion if battery is incorrectly replaced, replace only with the same or
equivalent type.
DISC CLEANING, POWER FAILURE
1
3
Cleaning the Disc
1. To handle a disc use only one of the two
manners.
Note: Do not touch the rainbow colored side.
2. To wipe a disc, use only a soft cloth. Do not
use benzene or thinner which will damage
the disc, the disc should always be wiped
in a straight line from the centre to the edge.
It should never be wiped in a circular motion.
3. Never place the disc on other equipment or
near any heat source. Avoid positions
where the disc would be subjected to
direct sunlight for long periods.
NOTE: This system has polarized AC plug with one wide blade and one narrow blade.
This plug will only fit into a matching polarized AC outlet.
This is a safety feature to reduce the possibility of electric shock. If this plug will not fit
in your AC outlet, you probably have an outdated non-polarized outlet. You should
have your outdated outlet changed by a qualified, licensed electrician.
Do not file the wide blade on the plug, or use an adapter to make the plug fit into your
outlet. This defeats the safety feature and could expose you to electric shock.
24. Pigtail FM Antenna
SETTING THE CLOCK/TIME
. Connect the AC power cord to a wall outlet.
1.12:00 will show on the display and begin to flash.
2.Press >>I /HOUR button to set the hour and then press I<< / MINUTE button to set
the minute.
3.Press the CLOCK ADJ button to confirm the time, the display will stop flashing.
4.You can switch the clock display between 12H and 24H by holding the CLOCK ADJ
button for 2 seconds.
5.During OFF MODE, you can press the CLOCK ADJ button and then repeat step 2
and 3 to change the time as well.
Remarks: The clock does not keep time during a power failure unless backup
batteries are fitted (See“Power Connection”on page 4)
LISTENING TO THE RADIO
AC Outlet
AC Plug
5
1.Slide the function (CD/AM/FM/BUZZER) switch to AM or FM position ,
2.Press the ON/OFF button to switch ON the unit, the power ON indicator will light up
on display.
3.Adjust the VOLUME control to the desired level.
4.Tune into a station using the TUNING control.
7
ANTENNA
FM: Extend the FM aerial wire to improve FM reception.
AM: Turn the unit for better AM reception.
CD PLAYING
1. Press OPEN button to open the disc compartment.
2. Place a disc in the centre with the label side facing up and close the Disc
compartment.
3. Slide the function (CD/AM/FM/BUZZER) switch to CD position, then press the
ON/OFF button into ON status.
4. The total number of tracks will show on the display for 2 seconds and then the
display will turn back to clock display.
5. Press PLAY/PAUSE button to start playing the disc.
Notes: You can press the DISPLAY button to show the current track number that is
playing current to the total number of tracks during STOP position in CD
mode.
IMPORTANT:
When you connect a cable to the AUX IN input jack of this unit the FUNCTION
selector automatically switches from Radio or CD to Auxiliary Input.
You must disconnect the cable from the AUX IN input jack in order to listen to the
Radio or CD again.
After connecting your external device to the AUX IN input jack, slowly adjust both the
volume controls on this unit and your external device to find the desired setting.
Please note that if the VOLUME control on this radio is set to a low level while the
VOLUME control on your external device is set too high, the sound will be distorted.
Remember to disconnect the connection cable after use in order to be able to listen
to the Radio or CD player again.
To stop Playback
Press STOP button
To pause Playback
Press PLAY/PAUSE button, To resume
playback, press it again
To search for the beginning of a track
Press I<< /MINUTE or >>I/HOUR button
briefly
To locate a desired passage
Keep I<< /MINUTE or >>I/HOUR pressed.
Release the button at the start of the
desired passage.
8
AUX IN FUNCTION
Connect the audio output socket of your auxiliary sound source to the AUX IN socket
on the top of unit.
DON’T FORGET! The auxiliary function can only be used when there is a connection
made to the AUX IN socket from another source.
Auxiliary Input Jack (Connection Cable Not Included)
This unit includes an AUX IN input jack to allow you to connect external devices,such
as portable MP3 player, and listen to the music stored on your external device through
the speakers of this radio.
Connect the AUX jack of your external device to the AUX IN input jack located
on the top cabinet of this unit. The connection cable is not included.
Emerson Returns Facility
11500 Philadelphia ST
Mira Loma, CA 91752
ATTN: Returns Department.
REPEAT/RANDOM
Press the REPEAT/RANDOM button in STOP or PLAY mode. A single track, all tracks
can repeat or random can play.
Each press changes the repeat mode as follows:
1 REPEAT
BASIC OPERATION
LIMITED WARRANTY
Emerson Radio Corp. Warrants manufacturing defects in original material,including
original parts and workmanship, under normal use and conditions, for a period of
ninety(90)days from the date of original purchase in the U.S. With your dated proof
of purchase, we will provide repair service at no charge for labor and parts or
replace the productat our discretion. For repair or replacement,pack your unit
in a padded box, enclose your check or money order payable to Emerson Radio
Corp.in the amount of $9.00 to cover shipping and handling costs,and enclose
a copy of your proof of purchase. Send your unit to:
(Repeat indicator
will flash)
2 REPEAT ALL
(Repeat indicator
will be steady on)
3 RANDOM/REPEAT OFF
(Random indicator will be
steady on) (Repeat
indicator will be off)
This warranty does not cover damage from negligence ,misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
4 REPEAT/RANDOM OFF
(Repeat indicator ,
and random
indicator will turn off)
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898N
PROGRAMMED DISC PLAY
Up to 20 tracks can be programmed to play in a specific order by following these steps.
1.Set the CD/AM/FM/BUZZER switch to CD.
2.Press the ON/OFF button into ON status, the ON indicator will light up on display.
3.In STOP mode press the PROGRAM button.
4.Press the I<< /MINUTE or >>I/HOUR button to select the track number.
5.Press the PROGRAM button when the desired track number is displayed.
6.Repeat step 4 and 5 to program more tracks.
7.Press the PLAY/PAUSE button to start programmed playback.
To check the program:
Press the PROGRAM button during STOP mode. The programmed track number will be
displayed in programmed order each time you press the PROGRAM button.
To erase the program:
• Press the PROGRAM button and then the STOP button when the CD is stopped.
• Opening the disc compartment will also erase the contents of program memory.
The Serial Number can be found on the bottom cabinet. We suggest that you record
the Serial Number of your unit in the space below for future reference.
Model No:CKD2020
Serial Number:
10
12
TO SET THE ALARM TO WAKE TO BUZZER/CD/ RADIO
The radio, buzzer or CD automatically sounds at the designated time every day.
You can set in total two wake up times(ALARM 1, ALARM 2) into this unit.
Wake by CD/AM/FM/BUZZER.
1.Press the ALARM 1 or ALARM 2 button, the display will flash.
2.Use the MINUTE or HOUR button to set the desire wake up time.
3.Press the ALARM 1 or ALARM 2 button after setting, The Alarm 1 /Alarm 2 active
indicator will light up on the display respectively.
4.Slide the CD/AM/FM/BUZZER selector into BUZZER position for BUZZER wake up.
In order to wake by CD, slide the CD/AM/FM/BUZZER selector into CD. In order to
wake by radio, slide the selector into AM or FM position then tune to your desired
AM or FM station and adjust the volume.
5.To Turn off but not cancel the alarm, press the "ON/OFF" button. The alarm will
stop and automatically resets for the following day.
6. To cancel the alarm if the alarm is off, press the ALARM 1 and/or ALARM 2 buttons
once. The respective ALM indicator should disappear. To cancel the alarm if the
alarm is on, press the ALARM 1 and/or ALARM 2 buttons twice. Again, the
respective ALM indicator should disappear.
NOTE:
1. When you connect a cable to the "AUX IN" input jack, ALARM SOUND will be
"BUZZER SOUND" only once ALARM is activated.
2. If there is no CD in CD compartment or CD is not readable, ALARM SOUND will be
"BUZZER SOUND" only once ALARM is activated while FUNCTION (CD/AM/FM/
BUZZER) switch is set to "CD" position
SNOOZE
The alarm can be temporarily turned off by pressing the SNOOZE button; the
ALARM 1 or ALARM 2 indicator will flash at this time/ the alarm will turn back on
automatically 6 minutes later.
TO ACTIVATE THE SLEEP FUNCTION
Turn on your desired radio station or play a CD as previously instructed.
1. Press the SLEEP button and the SLEEP indicator will light up on the display.
2. Repeatedly press the SLEEP button for the desired sleep time, 90,60,30,15
minute the SLEEP indicator will light to indicate the sleep mode is activated.
3. To cancel sleep time, press the SLEEP button again until the SLEEP indicator
goes off.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020 OR
1-800-695-0098 OR
E-MAIL TO: internet @ emersonradio.com
CKD2020-905-02
9
11
Printed in China