Owner`s manual | Emerson CKD9906 Stereo System User Manual

Stereo Radio, CD-R/RW Player
with Dual Alarm Clock
OWNER'S MANUAL
CKD9906
Visit our web site at www.emersonradio.com
CKD9906_071905.p65
27
19/7/2005, 14:24
CAUT I ON
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
C AU T I O N
!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence
of uninsulated ‘dangerous voltage’
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE PARTS INSIDE
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is intended to alert the user to
the presence of important
operating and maintenance
(ser vi ci ng) instr ucti ons in
the liter ature accompanying the appl iance.
The Caution Marking was located at the bottom enclosure of the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions.
2.) Keep these instructions.
3.) Heed all warnings.
4.) Follow all instructions.
5.) Do not use this apparatus near water.
6.) Clean only with dry cloth.
7.) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11.) Only use attachments / accessories specified by the manufacturer.
12.) Unplug this apparatus during lightning storms or when unused for long periods of time.
13.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
14.) This appliance shall not be exposed to dripping or splashing water and no object filled with liquids
such as vases shall be placed on the apparatus.
15.) Do not overload wall outlet. Use only power source as indicated.
16.) Use replacement parts as specified by the manufacturer.
17.) The product may be mounted to a wall only if recommended by the manufacturer.
18.) Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks.
1
CKD9906_071905.p65
1
19/7/2005, 14:26
Before We Begin
Thank you for purchasing this Emerson audio product. The Emerson brand
is your assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this
product. Please be sure to read this owner's manual completely to make
sure you are getting the maximum benefit from each feature.
This product was manufactured using the highest quality components and
standards of workmanship. It was tested by Emerson inspectors and found
to be in perfect working order before it left our factory. However, there is
always the chance that some problem may occur because of rough handling
during shipment to the retail store or to the final consumer.
If, after reading this manual, you experience any problems with the operation
of this product, please refer to the instructions for obtaining service at the
end of this manual. Emerson and Emerson retailers are committed to your
satisfaction.
Once again, thanks for purchasing this Emerson audio product.
2
CKD9906_071905.p65
2
19/7/2005, 14:26
IMPORTANT NOTES
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or
dusty areas, places subject to constant
vibration and/or humid or moist areas.
• Operate controls and switches as
described in the manual.
• Before turning ‘On’ the power, make
certain that the power cord is properly
installed. When moving the set, be
sure to first disconnect the power cord.
• Store your CDs, in a cool area to avoid
damage from heat.
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
FCC Information
This equipment has been tested and found to comply with the limits for a class B
digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
3
CKD9906_071905.p65
3
19/7/2005, 14:26
PREPARATION FOR USE
Unpacking And Set Up
• Remove the unit from the carton, and remove all packing materials from the
unit.
• Save the carton and packing materials in case the unit ever needs to be returned
for service. Using the original carton and packing materials is the only way to
safely repack the unit for shipment.
• Remove any descriptive labels or stickers from the top or front of the unit. Do
not remove any labels from the back or bottom of the cabinet.
• Remove any small strips of tape that may have been used to prevent the CD
door from opening in transit.
• Press on the OPEN/CLOSE area on the CD door to open the CD door, and
remove the dummy CD protection card from the CD compartment. Discard it
and close the CD door.
• Unwind the FM wire antenna on the back cabinet and extend it to its full length.
• Unwind the AC power cord and extend it to its full length.
• Place the unit on a stable, level surface such as a table, desk, shelf, etc within
easy reach of an AC outlet, out of direct sunlight, and away from sources of
excessive heat, dust, moisture or humidity.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
4
CKD9906_071905.p65
4
19/7/2005, 14:26
Power Source
This system is designed to operate on 120V AC 60Hz house current only.
Connecting this system to any other power source may cause damage to the
system and such damage is not covered by your warranty.
Note: The system has polarized AC plug with one wide blade and one narrow
blade. The plug will only fit into matching polarized AC outlets.
This is a safety feature to reduce the possibility of electric shock. If the plug will not
fit in your AC outlet, you probably have an outdated non-polarized outlet. You should
have your outdated outlet changed by a qualified, licensed electrician.
Do not file the wide blade on the plug, or use an adapter to make the plug fit into
your outlet. This defeats the safety feature and could expose you to electric shock.
AC Outlet
AC Plug
5
CKD9906_071905.p65
5
19/7/2005, 14:26
Battery Back Up System
This unit uses a single 9-Volt battery (not included) to maintain the time and alarm
settings in the event that it is accidentally unplugged, or you experience a temporary
power failure. We recommend that you install a well-known brand of Alkaline battery
for longest life and best performance. To keep the battery back up system operational
you should install a new battery every 6 to 9 months. Some people find it convenient
to replace the back up batteries in their alarm clocks, clock radios, and smoke
detectors too, at the beginning and end of Daylight Saving Time.
To install the back up battery, turn the unit upside down, and
1.) Press on the battery door “ ” mark and slide it in the direction of the “arrow” to
open.
2.) Connect the battery to the battery terminal, push the battery back into the
compartment and replace the battery door.
If the power is interrupted the clock display will go off but the battery will maintain
the clock and alarm time settings. When power is restored the time display will be
correct and your alarm setting will also be maintained.
If you notice that the time display is “flashing” you probably experienced a power
failure with a weak or exhausted battery in the compartment. Reset the clock and
replace the battery as soon as possible.
6
CKD9906_071905.p65
6
19/7/2005, 14:26
LOCATION OF CONTROLS AND INDICATORS
Top Panel
8
7
9
10
11
6
12
13
14
15
16
5
5
4
3
19
2
18
20
21
1
23
Front Panel
22
26
27
25
28
24
29
33
32 31
30
7
CKD9906_071905.p65
17
7
19/7/2005, 14:26
1.) SNOOZE Button.
2.) BUZZER-CD-FM ST-AM Selector Switch.
3.) Power ‘On’ Indicator.
4.)
POWER(On/Off)/ALARM OFF Button.
5.) Speakers.
6.) CD compartment.
8.) AC Power Cord.
7.) Back Up Battery Compartment (At bottom cabinet).
9.) FM W ire Antenna.
10.) VOLUME Control.
11.) TUNING Control.
12.)
13.)
Play/Pause Button.
Stop Button.
14.) CD Door OPEN/CLOSE Area.
15.)
Skip Search Forward/HR.(Hour) Button.
16.)
Skip Search Reverse/MIN.(Minute) Button.
17.) P-MODE Button.
18.) PROGRAM Button.
19.) AL(Alarm) 1 SET Button.
20.) SLEEP Button.
21.) AL(Alarm) 2 SET Button.
22.) TIME Button.
23.) DISPLAY Button.
24.) ALARM 1 ‘On’ Indicator.
25.) PM Indicator.
26.) FM STEREO Indicator.
27.) Tuning Dial pointer.
28.) LED Display.
29.) ALARM 2 ‘On’ Indicator.
30.) REPEAT Indicator.
31.) RANDOM Indicator.
32.) PROGRAM Indicator.
33.) SLEEP Indicator.
8
CKD9906_071905.p65
8
19/7/2005, 14:26
OPERATING INSTRUCTIONS
Setting The Time Of Day
• Connect the power cord to your AC outlet. Make sure to use an outlet that is
always ‘live’. Do not use an outlet that is controlled by a wall switch.
• When the unit is plugged in for the first time the
display will show flashing “12:00” (AM).
PM
ALARM 1
ALARM 2
1.) While the display is flashing, press the
HR. button to set the hour. Be sure
to observe the PM indicator to set the hour correctly. If the PM indicator is ‘On’
the hour displayed is PM.
2.) Press
MIN. button to set the minute correctly..
PM
3.) Press the TIME button once. The time is set.
ALARM 1
The display remains ‘On’.
ALARM 2
Note: You may proceed to re-set the time again by pressing the TIME button
once during Power-off or CD, FM, AM, Buzzer modes.
Important Notes !!
If you press and hold the TIME button any time, the clock will change to
European 24-Hour format, and vice versa.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
9
CKD9906_071905.p65
9
19/7/2005, 14:26
Setting The Wake Up Times
The unit has two separate wake up alarms that can be set and used independently.
1.) Press the AL 1 or AL 2 button once. The display will change from the respective
time of the day to wake up time and begin flashing.
The ALARM 1 or ALARM 2 indicator comes “On”.
2.) Press the
HR. button to set the wake up hour. Set correctly for AM or PM.
3.) Press the
MIN. button to set the minute correctly..
Press the respective AL button once. The Alarm time is set.
The display returns to correct time.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
Note: Press the AL 1 or AL 2 button once to turn the respective Alarm time
‘Off’. The ALARM 1 or ALARM 2 indicator will go ‘Off’.
10
CKD9906_071905.p65
10
19/7/2005, 14:26
Listening To The Radio
1.) Press the
POWER/ALARM OFF Button to turn the unit ‘On’. The Power
indicator comes ‘On’.
2.) Set the BUZZER-CD-FM ST-AM selector to FM ST or AM position.
3.) Turn the TUNING control to find the desired station.
If you slide the selector to FM ST position, and tune to a FM Stereo station, the
FM STEREO indicator light comes ‘On’.
FM STEREO
PM
ALARM 1
ALARM 2
4.) Adjust the VOLUME control to the desired level.
5.) When you are finished listening press the
POWER/ALARM OFF button
to turn the unit ‘Off’. The Power indicator goes ‘Off’.
11
CKD9906_071905.p65
11
19/7/2005, 14:26
Antenna Information
AM
The AM ferrite bar antenna is inside the cabinet. If AM reception is unsatisfactory
try turning the entire unit slightly until you find the direction that provides the best
reception for the desired station.
FM
Make sure the FM lead wire antenna is extended to it’s full length. You may have to
vary the direction of the wire antenna to find the position that provides the best
reception.
12
CKD9906_071905.p65
12
19/7/2005, 14:26
Playing Compact Discs
Note: Although this CD player can read CD-R and CD-RW discs, in addition to
normal CDs, however the playability of CD-R/RW discs may be affected by
the type of software that was used to create the discs, as well as the quality
and condition of the blank media you are using. 100% playability cannot be
guaranteed. This is not an indication of a problem with the player.
Normal Playback
1.) Press the
POWER/ALARM OFF button to turn the unit ‘On’. The Power
indicator comes ‘On’.
2.) Set the BUZZER-CD-FM ST-AM selector to the CD position.
3.) Press on the OPEN/CLOSE position on CD door to open the CD door.
4.) Place your disc on the center spindle with the printed label side facing up.
Close the CD door.
13
CKD9906_071905.p65
13
19/7/2005, 14:26
5.) Two dashes “– –” flash while the player reads the table of contents of the disc.
The display will show the total number of tracks for a few seconds and then
return to the correct time.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
PM
ALARM 1
ALARM 2
Note: If the disc is inserted incorrectly, or if the disc is badly scratched
and cannot be read by the player, “no” will appear on the display for a few
seconds, and then the display returns to the correct time.
PM
PM
ALARM 1
ALARM 1
ALARM 2
6.) Press the
ALARM 2
button to begin playback.
The display will briefly show “01” (Track 01) and playback on track 01 begins.
After a few seconds the display returns to the correct time.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
Press the DISPLAY button to return to Track number again for few seconds.
7.) To Pause briefly during playback press the
button.
The track number flashes briefly and the sound stops, but the disc continues
to spin.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
Press
button again to cancel pause and resume playback.
8.) To skip forward or backward to other tracks repeatedly press the
or
buttons until the desired track number appears in the display. Playback will
begin on the selected track.
9.) To stop playback at any time press the
Stop button. After the last track has
s
played the disc stops automatically. Open the CD door and remove your disc.
14
CKD9906_071905.p65
14
19/7/2005, 14:26
To Start Playback From A Specific Track
Load your disc and wait until the display shows the total number of tracks.
Press the
or
buttons to select the desired track.
PM
While the track number is still flashing press the
ALARM 1
button.
ALARM 2
Playback will begin on the selected track and continue until the end of the disc.
High Speed Music Search
You can search rapidly forward or backward within a track to locate a specific
musical passage.
Depress and hold the
or
buttons to begin high speed search. The display
will show the current track and the player moves rapidly forward or backward.
When you reach the desired passage release the
playback resumes.
or
button and normal
Note: The volume level is automatically reduced during high speed music
search.
Random Playback
To listen to the tracks on a disc in random order:
1.) Load your disc and wait until the total track number is displayed.
2.) Press the P-MODE button three times.
PM
ALARM 1
The RANDOM indicator comes ‘On’.
3.) Press the
ALARM 2
button. The player will select a track at random and playback
begins on that track. The selected track number appears in the display for a
few seconds.
After each track has played once the player stops automatically.
To cancel random playback at any time, press the P-MODE button until RANDOM
indicator goes ‘Off’.
15
CKD9906_071905.p65
15
19/7/2005, 14:26
Repeat Playback
You can program the player to repeat a single track or the entire disc continuously.
One Track Repeat
1.) Load your disc and wait until the total track number is displayed.
2.) Press the P-MODE button once.
PM
ALARM 1
The REPEAT indicator flashes.
3.) Press
or
ALARM 2
button to select the track to be repeated.
When the track number is still flashing, press
the
button. The selected track will be
PM
ALARM 1
ALARM 2
repeated continuously.
All Tracks Repeat
1.) Load your disc and wait until the total track number is displayed.
2.) Press the P-MODE button twice.
PM
ALARM 1
The REPEAT indicator remains ‘On’.
3.) Press the
ALARM 2
button. All tracks will be repeated continuously..
To cancel repeat playback press the P-MODE button until the REPEAT indicator
goes ‘Off’, or press the
Stop button.
16
CKD9906_071905.p65
16
19/7/2005, 14:26
Programmed Playback
The CD player in this unit has a 20 track programmable memory which allows you
to program any disc to play just the tracks you want to hear in the exact order that
you want to hear them. You may program a track or tracks to play more than once
if desired.
Note: Programming can only be done while the player is in the Stop mode. If
Stop button to stop playback before performing
a disc is playing press the
the programming steps below.
1.) Turn the unit ‘On’, select the CD function and load the desired disc in the
player. Wait until the player reads the disc and the display shows the total track
number.
2.) Press the PROGRAM button. The PROGRAM indicator flashes and the display
briefly shows “P 01” then “00” flashes indicating that you can select the first
track to be programmed.
PM
PM
ALARM 1
ALARM 1
ALARM 2
3.) Press the
or
ALARM 2
buttons to select the first
PM
track. The desired track number flashes on the
ALARM 1
display.
ALARM 2
4.) Press the PROGRAM button again. The selected track is entered in program
memory number 01 and the display advances to “P 02” then “00” flashes again
indicating that you can select the next track to be programmed.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
or
buttons to select the next track to be programmed, and
nd
5.) Press the
press the PROGRAM button to enter the track in the memory.
6.) Repeat step 5 to program up to 20 tracks in the memory.
17
CKD9906_071905.p65
17
19/7/2005, 14:26
7.) After you have programmed all the desired tracks press the
button to begin
programmed playback.
The PROGRAM indicator stops flashing and remains ‘On’. Playback will begin
on the first track you programmed and continue until all programmed tracks
have been played.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
Notes:
• After all programmed tracks have played the player stops but the program
remains in the memory.
Press the PROGRAM button and then the
button to begin programmed
playback again.
• To clear the program from the memory after the disc stops, press the
PROGRAM button and then press the
Opening the CD door, pressing the
Stop button.
POWER/ALARM OFF button to shut
the unit ‘Off’, or by switching to other function also clears the program.
Program Repeat Playback
You may use the Program and Repeat features together to repeat a programmed
sequence of tracks.
Simply enter the desired tracks in the program memory as described on page 17,
then press the P-MODE button twice to select ‘All Tracks Repeat’.
PM
The PROGRAM and REPEAT indicators will both
ALARM 1
come ‘On’.
Press
ALARM 2
to begin Program Repeat playback.
18
CKD9906_071905.p65
18
19/7/2005, 14:26
Alarm Operation
This unit gives you the option of waking to an electronic Buzzer alarm, the AM/FM
Radio, or the CD player.
Note: Whichever alarm mode you select – BUZZER, CD, FM ST or AM – will
apply to both alarms.
Refer to “Setting The Wake Up Times” on page 10. Adjust the wake up time(s) if
necessary.
1.) Set the BUZZER-CD-FM ST-AM selector to the desired wake up mode.
2.) Press the AL 1 and/or AL 2 buttons once. The respective alarm time flashes
for few seconds, then returns to correct time.
PM
PM
ALARM 1
ALARM 1
ALARM 2
ALARM 2
The ALARM 1, ALARM 2 or both indicators come ‘On’.
3.) At the selected wake up time the selected alarm mode turns ‘On’.
PM
The ALARM indicator flashes.
ALARM 1
ALARM 2
The selected alarm will continue for 60 minutes and then turn ‘Off’and reset
itself for the following day.
4.) To stop the alarm immediately, press the
POWER/ALARM OFF button.
The alarm stops and resets itself for the following day.
5.) To cancel the alarm completely press the AL 1 and/or AL 2 buttons once to
turn ‘Off’. The respective ALARM indicator disappears.
19
CKD9906_071905.p65
19
19/7/2005, 14:26
Notes:
A.) If “Waking to Radio”, make sure you have tuned to the desired station and
adjusted the volume to the desired level.
B.) If “Waking to CD”, make sure there is a CD in the player and the volume is
set to the desired level.
C.) In CD wake up mode the CD will play for 60 minutes, or until the end of the
disc, whichever comes first.
Snooze/Repeat Alarm
After the alarm turns ‘On’in the morning you can press the SNOOZE button for a
few extra minutes sleep. The alarm will stop for approximately 6 minutes and then
come on again. Snooze operation can be repeated several times if desired, but
after one hour the alarm will not turn ‘On’again.
20
CKD9906_071905.p65
20
19/7/2005, 14:26
Sleep To Music Timer
You can use the sleep timer to fall asleep to the Radio or CD player for 90, 60, 30
or 15 minutes and have the unit shut off automatically.
POWER/ALARM OFF button or simply the SLEEP button to
• Press the
turn the power ‘On’.
Operate the Radio or CD player as usual. Adjust the volume to the desired
level. The level you select for “Sleep To Music” is the same level you will hear
when the alarm turns ‘On’in the morning.
PM
• Press the SLEEP button to select the desired
amount of sleep time as follows:
ALARM 1
ALARM 2
Display
Meaning
1st Press
“90”
90 Minutes Till Shut Off.
2nd Press
“60”
60 Minutes Till Shut Off.
3rd Press
“30”
30 Minutes Till Shut Off.
4th Press
“15”
15 Minutes Till Shut Off.
5th Press
“Correct Time”
Sleep Off.
• When the display shows the desired amount of time, stop pressing the SLEEP
button.
PM
After 5 seconds the display changes back to
the correct time.
ALARM 1
ALARM 2
The Radio or CD player will continue until the sleep timer counts down to “00”
and then shut off automatically.
• To stop the Radio or CD player before the sleep timer counts down to “00”,
press the
POWER/ALARM OFF button to turn the unit ‘Off’.
Notes:
• If you set the sleep time for either 90 or 60 minutes and you are playing a
CD that is only 48 minutes long, for example, playback will stop at the end
of the disc.
• Be sure the BUZZER-CD-FM ST-AM selector is set to the CD, FM ST or
AM position before you press the SLEEP button.
No sound will be heard if the BUZZER-CD-FM ST-AM selector is set to
the BUZZER position.
21
CKD9906_071905.p65
21
19/7/2005, 14:26
CARE AND MAINTENANCE
Compact Disc Care
• To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
• Fingerprints and dust should be carefully wiped off the disc’s recorded surface
with a soft cloth.Unlike conventional records, compact discs have no grooves
to collect dust and microscopic debris, so gently wiping with a soft cloth should
remove most particles. Wipe in a straight line from the inside to the outside of
the disc. Small dust particles and light stains will have absolutely no effect on
reproduction quality.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• Never write on or affix labels to the surface of compact discs.
22
CKD9906_071905.p65
22
19/7/2005, 14:26
Care Of The Cabinet
• If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any
wax or polish sprays on the cabinet.
• If the front panel becomes dirty or smudged with fingerprints it may be cleaned
with a soft cloth slightly dampened with a mild soap and water solution. Never
use abrasive cloths or polishes as these will mar the finish of your unit.
Caution
Never allow any water or other liquids to get inside the unit while cleaning.
23
CKD9906_071905.p65
23
19/7/2005, 14:26
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service.
Symptom
Radio
Possible Cause
Solution
Noise or sound
distorted on AM or FM
Station not tuned properly for
FM ST or AM.
Retune the FM ST or AM
broadcast station.
broadcasts.
FM: FM Wire antenna is not
extended.
Extend FM Wire antenna.
AM: The bar antenna is not
positioned correctly.
Reposition the unit until
best reception is obtained.
FM ST. indicator
does not light.
You have tuned to a FM mono
station.
Select another FM stereo
station and set to FM ST.
AM or FM, no sound.
Function switch is not set to
AM or FM ST.
Set Function switch to
AM or FM ST. as desired.
Volume at minimum.
Increase Volume.
Function switch is not set to
CD.
Set Function switch to
CD.
CD is not installed or installed
incorrectly.
Insert CD with Iabel side
up.
Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
Compact Disc Player
CD Player will not play.
CD skips while playing.
R
SERVICE
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
CENTER PERMITTED TO PERFORM
WARRANTY...
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
5101 Statesman Drive,
Irving, TX 75063.
24
CKD9906_071905.p65
24
19/7/2005, 14:26
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.,
5101 Statesman Drive,
Irving, TX 75063.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
The serial number can be found on the bottom cabinet. We suggest that
you record the serial number of your unit in the space below for future
reference.
Model No: CKD9906
Serial Number:
25
CKD9906_071905.p65
25
19/7/2005, 14:26
EMERSON
Part No. 16-2989
Printed in China
507-02
CKD9906_071905.p65
26
19/7/2005, 14:26
Download PDF

advertising