Owner`s manual | Emerson EM229 Bluetooth Headset User Manual

Drive Safe
Pairing the headset
CAUTION: Although this device enables drivers to
conduct handsfree conversations, it is still safer to pull
over before using a mobile phone.
Always keep your full attention on your driving.
WI REL E S S H E A D S E T
Driving while talking on your mobile phone is dangerous, and
illegal in many states.
Check local laws regarding the use of a mobile handset and wireless
headset while driving. If you use the Bluetooth Headset while
driving, ensure your attention and focus remains on your driving.
Please use your mobile phone, and our
product responsibly while driving!
Easy Pairing
(First time pairing only)
6. When the phone finds the headset, confirm by selecting
EM229 from the list.
Bluetooth: Enabled
Paired Devices:
EM229
Please read through this section before turning the
device on.
This Bluetooth headset has an “Easy Pairing” feature which
sets the headset to Pairing Mode the first time the power
switch is turned on.
1. Make sure the Bluetooth Headset is within 3 feet of
your mobile phone or Bluetooth enabled device.
Select Device:
7. Enter the passcode “0000” when prompted by the phone.
EM229
Location of controls
Enter numeric passkey
for EM229:
OK
Power ON/OFF
(Green = ON, Red = OFF)
Speaker/
Silicone cushion
Call button
Answer/end a call
Volume up
2. Set the [Power] switch to the ON position. The indicator
light should be flashing RED and BLUE alternately,
indicating the headset is in Pairing Mode and ready to
connect to your Bluetooth enabled device.
Volume down
3. Continue to “Manual Pairing” step 5 shown below.
(Press 3 seconds to redial)
Charging
socket
Indicator light
Model: EM229
Microphone
Charging the headset
Owner’s Manual
Model: EM229
Owner’s
Manual
Bluetooth
Headset
1. Connect the charging pin of the USB cable to the charging
socket of the headset.
2. Connect the other end of the USB cable to either the:
• AC Charger, and plug into a wall (A/C) outlet
• Computer’s USB port
• Car Charger
3. The RED LED indicator light turns on while the headset is
charging.
4. The RED LED indicator light shuts off when the headset is
fully charged (approximately 2-3 hours).
OR depending on which model mobile phone you are trying
to connect the headset to, it may not be necessary to enter a
passcode and the following message (or similar) may appear on
your phone’s display.
Bluetooth: Enabled
Paired Devices:
EM229
Note: Manual Pairing
If the first time pairing was unsuccessful or for
future pairing, you will need to manually pair the
headset to your Bluetooth enabled device (see
“Manual Pairing” below).
Manual Pairing
“EM229” would like to pair
with your phone. Would you
like to allow it to pair?
Cancel
Pair
Select “Pair” to complete the pairing process.
1. Make sure the Bluetooth Headset is within 3 feet of your
mobile phone or Bluetooth enabled device.
2. Set the [Power] switch to the ON position.
3. Press and HOLD the [Call] button until the indicator light
flashes RED and BLUE alternately.
4. The headset is now in Pairing Mode and is ready to connect
to your mobile phone or Bluetooth enabled device.
8. Your mobile phone will confirm that the pairing process was
completed and prompt you to accept the connection.
Please select “YES” to connect the headset to your mobile
phone. If the pairing was successful, the headset’s indicator
light turns to standby mode and flashes once every three
seconds.
YES
Indicator light
Indicator
light
NOTE: To enter Pairing Mode at any time, you must press and
HOLD the [Call] button for approximately 10 seconds.
Headset
5. Set your mobile phone to search for Bluetooth devices.
Bluetooth: Enabled
Paired Devices:
AC charger
/
NO
AC Charger
Car Charger
PC
Car Charger
NOTE: Charge the headset for at least 8 hours before using it
for the first time, even if the RED LED indicator shuts off.
9. When attempting to reconnect the headset to your mobile
phone, you may see the message below and your mobile
phone will prompt you to accept the connection request to
the EM229 headset, and an option not to ask this again.
Please accept the connection, and if you select “Don’t ask this
again”, your phone will automatically accept future connection
requests from the headset.
1 found
Stop
Switching calls between two connected phones
1. While on a call with one phone and the second phone rings
with an incoming call, press and HOLD the [Volume Up]
button briefly to answer the 2nd call and place the first
phone on hold.
Call button
Press & Hold
to switch calls
Bluetooth: Enabled
Paired Devices:
EM229
*Empty *
Searching for devices
Earhook
7. Your mobile phone will confirm that the pairing process
was completed. Select “Yes” to connect the headset to
your second mobile phone. If the pairing was successful,
the headset’s indicator light turns to standby mode and
flashes once every three seconds.
8. After pairing the second phone, by default the first phone
will be disconnected from the headset. Enter the first
phone’s Bluetooth settings screen and connect it to the
headset. Both phones should now be connected to the
headset.
Confirm connection to
EM229?
Power ON/OFF
(Green = ON, Red = OFF)
USB cable
Charging
Socket
OR
depending on which model phone you are trying to connect
the headset to, it may not be necessary to enter a passcode.
Select “Pair” to complete the pairing process.
EM229
within 3 feet
USB charging
cable
3. The headset is now in Pairing Mode and is ready to connect
to your second mobile phone.
4. Set your second mobile phone to search for Bluetooth
devices.
5. When the second phone finds the headset, confirm by
selecting EM229 from the list.
6. Enter passcode “0000” when prompted by the second phone
Bluetooth: Enabled
Paired Devices:
Power Switch
NOTE: When the battery is running low, the RED LED indicator
light starts to flash along with a warning beep.
S M L
Silicone cushions
Press & hold
to pair 2nd phone
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
WIR E L E S S H E A D S E T
Pairing a second phone (Multi-Link)
1. Make sure the headset is turned ON and connected to the
first phone.
2. Press and HOLD the [Volume Down] button for 3 seconds
or until the headset’s indicator light flashes RED and BLUE
alternately.
0000
Power Switch
In the box
NOTE: This headset is capable of pairing to two mobile
phones at the same time.
Cancel
Indicator light
Owner’s Manual
Pairing the headset with a 2nd mobile phone
EM229
Bluetooth: Enabled
Paired Devices:
within 3 feet
NOTE: The screenshots above are typical of many Bluetooth
enabled phones in the market today, and are used to
assist in the explanation of the pairing process. Your
mobile phone’s or Bluetooth enabled device’s interface
and interaction with the headset may be slightly
different from the illustrations shown.
Accept connection request
from EM229?
YES
/
NO
Don’t ask this again
2. Press and HOLD the [Volume Up] button briefly to switch
between the two phones and place the current phone on
hold.
3. To hang up the current call, press the [Call] button. The
headset will end the current call and return to the other
phone which was placed on hold.
4. To end that call, press the [Call] button or press the [End]
key on your phone.
Using the headset
Connecting to other devices
Volume
NOTE: When the [Power] switch is set to the ON position for
the first time, the headset will be in Pairing Mode (the
indicator light will be flashing RED and BLUE alternately),
please refer to “Easy Pairing”.
To adjust the volume, press the [Volume Up] or [Volume Down]
button.
Powering ON/OFF
Volume up
• To turn ON, set the [Power] switch to the ON position (green).
Although most people associate Bluetooth headsets with
mobile phones, there are many other products today which
include Bluetooth® wireless technology.
In most cases the pairing process is similar to pairing with a
mobile phone which is explained in detail in the "Manual
Pairing" section.
Volume down
Power Switch
Power ON
(Green)
Press and HOLD the [Volume Down] button for 3 seconds or
until you hear a confirmation beep, repeat to unmute the call.
Power Switch
Power OFF
(Red)
After successfully pairing my mobile phone
and headset, when I shut the phone and
turn it on again, the headset did not
automatically reconnect
• Try turning the headset OFF, and then turning it ON again.
• Many mobile phones have an auto reconnect option when first
attempting to reconnect to a newly paired Bluetooth device.
Make sure you accept this option, so that the headset
automatically reconnects to your mobile phone; check the user
guide of your mobile phone for more information regarding
this option.
• Try unpairing the headset from your phone, and repeat the
pairing procedure.
Volume down
(Press 3 seconds to mute)
Indicator light
Answering / Ending a call
• To answer a call, press and release the [Call] button or press
the answer key on your mobile phone.
• To end a call, press and release the [Call] button or press the
end key on your mobile phone.
Wearing your Bluetooth Headset
For added comfort and noise suppression, 3 silicone cushions
are included with the headset. Choose the silicone cushion (S)
(M) (L) which fits most comfortably in your ear and insert it on
the headset as shown in the diagram below.
S M L
Call button
Answer/end a call
Below, the pairing procedure with the Sony Playsation3 is
explained, to pair with other devices it is best to refer to the
device's Owner's Manual.
Pairing the headset with the SONY PlayStation®3
(PS3™)
Set accessory to Bluetooth on PS3
Silicone cushions
Rejecting a call
During an incoming call press and HOLD the [Call] button
for 3 seconds or until you hear a confirmation beep.
Making a call
You may wear the headset with or without the provided earhook.
If you choose to use the earhook, connect it to the headset as
shown in the diagram below.
1. Go to the PS3 main menu, scroll to and select “Settings”.
2. Scroll to and select “Accessory Settings”.
3. Scroll to and select “Manage Bluetooth Devices”.
4. The menu will ask: “The Bluetooth device has not been
registered. Do you want to register it?”, then select “YES”.
Registering the headset to PS3
1. Put the headset into pairing mode. (See “Manual Pairing”)
2. Select “Start Scanning” from the PS3 menu.
3. Once the PS3 has discovered the headset, the screen will read
“Select the Bluetooth device to register”, then select “EM229”
4. The PS3 will ask for a passkey. Enter “0000” then select “OK”. Now
press [O] (the PS3 circle button) to get back to the previous menu.
Dial the number and press the send button on your mobile
phone, the call is automatically transferred to the headset.
Earhook
5. Scroll to and select “Audio Device Settings” to change the
“Input Device” to “EM229”.
NOTE: “Input Device” is the microphone, and determines the
method of how others will hear you speak. By default,
the “Output Device” will now switch to “EM229”.
“Output Device” is the audio, and determines how you
will hear the PS3 audio and others speaking.
Redialing the last number called
(Dependent on your phone supporting this feature)
To test the connection, speak into the headset and you will see
the bars above the “Microphone Level” moving, if not, repeat the
pairing process.
Press the [Volume Up] button for 3 seconds and release. The
last number called will be redialed.
Press “OK” to confirm the new settings. You are now ready to use
the headset with your PS3 Entertainment System. If you would like
to hear the PS3 audio through your TV or Audio System, scroll to
“Output Device” and switch to “System Default Device”.
Volume up
(Press 3 seconds to redial)
Left ear
Right ear
NOTE: For the best audio quality, always wear the headset on
the same side of your body as your mobile phone.
• Make sure the headset is turned on before beginning the
pairing process (the headset is in pairing mode when you
turn it on for the first time).
• If you are not pairing for the first time or for manual pairing,
press and HOLD the [Call] button until the indicator light
flashes RED and BLUE alternately.
• Make sure that you fully charged the headset before pairing.
• Keep the headset and mobile phone within 3 feet of each
other during the pairing process.
• Check that your phone’s Bluetooth feature is turned ON.
• Try removing the battery from your mobile phone for 5 minutes.
Place the battery back in the phone, power it on, and retry the
pairing process (see “Manual Pairing”).
• Try repeating the pairing process, see “Manual pairing.”
Mute
• To turn OFF, slide the [Power] switch to the OFF position (red).
The indicator light will flash RED before the headset shuts
off.
I cannot get the headset into Pairing Mode
My mobile phone cannot pair with the headset
NOTE: You may also adjust the volume from your mobile phone’s
volume control.
Indicator light
Troubleshooting tips
For further assistance with Bluetooth settings on your PS3 please
refer to your PS3 instruction manual.
I hear distortion, and the sound quality is
poor
• For the best audio quality, always wear the headset on the same
side of the body as your mobile phone.
• Check that the battery is charged enough.
The sound is very low
• Try adjusting the volume by using the [VOLUME UP] or
[VOLUME DOWN] button on the headset; make sure the
volume on your mobile phone is turned up as well.
FCC and telephone company information
FCC Part 15
This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Do not attempt to repair or modify this equipment.
Warning: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Industry Canada
Operation is subject to the following two conditions: (1) This
device may not cause interference and (2) This device must
accept any interference, including interference that may
cause undesired operation of the device.
The term “IC:” before the certification/registration number
only signifies that registration was performed based on a
Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that
Industry Canada approved the equipment.
Warranty information
Limited Warranty
In the unlikely event that this product is defective, or does
not perform properly, you may within one (1) year from your
original date of purchase return it to the authorized service
center for repair or exchange.
TO OBTAIN WARRANTY SERVICE:
• Provide proof of the date of purchase within the package
(Dated bill of sale).
• Prepay all shipping costs to the authorized service center,
and remember to insure your return.
• Include a return shipping address (no P.O. Boxes),
a telephone contact number, and the defective unit within
the package.
• Describe the defect or reason you are returning the product.
Your product will be repaired or replaced, at our option, for the same
or similar model of equal value if examination by the service center
determines this product is defective. Products received damaged
as a result of shipping will require you to file a claim with the carrier.
The shipping address of the authorized service center is:
Southern Telecom, Inc.
ATTN: Customer Service - 2nd Floor
14-C 53rd Street
Brooklyn, NY 11232
Should you have any questions or problems concerning this
product, please contact our customer service department at:
1-877-768-8483 (Toll Free)
Monday - Thursday: 9AM - 5PM (EST)
Friday: 9AM - 3PM (EST)
or
via e-mail at
cs@southerntelecom.com
Warranty service not provided
This warranty does not cover damage resulting from accident,
misuse, abuse, improper installation or operation, lack of reasonable
care, and unauthorized modification. This warranty is voided in
the event any unauthorized person opens, alters or repairs this
product. All products being returned to the authorized service
center for repair must be suitably packaged.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY
APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION
GIVEN BY SOUTHERN TELECOM INC. IT’S AGENTS, OR EMPLOYEES
SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE
SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SOUTHERN
TELECOM INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER
OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED
BY THE LAWS OF THE STATE OF NEW YORK. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion nor limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts so the above limitations or exclusions may not apply
to you. This warranty gives you specific legal rights, and you
also may have other rights that vary from state to state.
www.emersonphones.com
Distributed by Southern Telecom Inc. Brooklyn, NY 11232
© 2011 Southern Telecom Inc. All rights reserved.
Emerson and the G-Clef logo are registered trademarks of
Emerson Radio Corp. Parsippany, New Jersey USA.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
SONY PlayStatiion® & PS3™ are either trademarks or registered
trademarks of SONY.
All other trademarks are trademarks of their respective owners.
Download PDF

advertising