Emerson EM6000 Cordless Telephone User Manual

RETURN TO MAIN MENU
CLASSIC 300G
®
IM659-B
December, 2004
For Machines with Code Numbers 10659,10912,11135
Safety Depends on You
Lincoln arc welding equipment
is designed and built with safety
in mind. However, your overall
safety can be increased by
proper installation ... and
thoughtful operation on your
part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT
WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT.
And, most importantly, think
before you act and be careful.
R
NRTL/C
OPERATOR’S MANUAL
Copyright © 2004 Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
i
i
SAFETY
WARNING
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituents
are known to the State of California to cause cancer, birth defects, and other reproductive harm.
The Above For Diesel Engines
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The Above For Gasoline Engines
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE
powered equipment.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporizing on contact with hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.
ELECTRIC AND
MAGNETIC FIELDS
may be dangerous
2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
2.d.5. Do not work next to welding power source.
Mar ‘95
ii
ii
SAFETY
ARC RAYS can burn.
ELECTRIC SHOCK can
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
5.b. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating products.
5.c. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.d. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.e. Also see item 1.b.
Mar ‘95
iii
iii
SAFETY
WELDING SPARKS can
cause fire or explosion.
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
6.h. Also see item 1.c.
CYLINDER may explode
if damaged.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Mar ‘95
iv
iv
SAFETY
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suivantes:
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du rayonnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pantalons sans revers, et chaussures montantes.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de levage, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debrancher à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
Mar. ‘93
v
v
Thank You
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.
vi
TABLE OF CONTENTS
vi
Page
Installation .......................................................................................................Section A
Technical Specifications ........................................................................................A-1
Safety Precautions.................................................................................................A-2
Pre-Operation Installation ......................................................................................A-2
Exhaust Spark Arrester ...................................................................................A-2
Location/Ventilation.........................................................................................A-2
Machine Grounding.........................................................................................A-2
Lift Bail ............................................................................................................A-2
Trailers ............................................................................................................A-2
Polarity Control and Cable Sizes ....................................................................A-3
Pre-Operation Service ...........................................................................................A-3
Oil....................................................................................................................A-3
Fuel .................................................................................................................A-3
Cooling System ...............................................................................................A-3
Battery Charging .............................................................................................A-4
Operation .........................................................................................................Section B
General Description ...............................................................................................B-1
Design Features ....................................................................................................B-1
Starting The GM 3.0L Engine..........................................................................B-2
Stopping the engine ........................................................................................B-2
Welder Operation...................................................................................................B-2
Duty Cycle.......................................................................................................B-2
Control of Welding Current..............................................................................B-3
Idler Operation ................................................................................................B-3
Auxiliary Power ...............................................................................................B-3
Throttle Body Deicing......................................................................................B-3
Accessories .....................................................................................................Section C
Optional Equipment (Field Installed) .....................................................................C-1
Maintenance ....................................................................................................Section D
Safety Precautions ................................................................................................D-1
General Instructions ..............................................................................................D-1
Cooling System .....................................................................................................D-1
Bearings ................................................................................................................D-1
Commutator and Brushes .....................................................................................D-1
Idler Control Maintenance .....................................................................................D-2
Nameplates ...........................................................................................................D-2
Purging Air from Fuel System................................................................................D-2
Engine Maintenance .............................................................................................D-2
Engine Service Chart ............................................................................................D-3
Troubleshooting ..............................................................................................Section E
Safety Precautions.................................................................................................E-1
Troubleshooting ..............................................................................................E-2,E-3
Electronic Idler Troubleshooting Guide...........................................................E-4,E-5
Troubleshooting .....................................................................................E-5, E-6,E-7
Diagrams ..........................................................................................................Section F
Wiring Diagram (Classic 300G) .......................................................................F-1,F-2
Dimension Print......................................................................................................F-3
Parts List ......................................................................................................P379 Series
A-1
A-1
INSTALLATION
TECHNICAL SPECIFICATIONS – CLASSIC 300G (K1754-1)
INPUT - GASOLINE ENGINE
Make/Model
Description
GM
3.0 Liter
4 Cylinder
4 Cycle
Water-Cooled
Gasoline Engine
Classic 300G
(K1754-1)
Speed (RPM)
Cast Iron Cylinder
Block/Crankcase
Displacement
cu. in. (Ltrs.)
Ignition
System
Capacities
High Idle 1800
Delco Voyager
High Energy
Fuel: 15 gal.
57 Ltrs.
Full Load 1800
Distributor Type
Oil: 4.5 Qts.
4.3 Ltrs.
183.0(3.0)
Electronic
Low Idle 1360
Cooling 9.9 Qts.
9.4 Ltrs.
53.0 HP @
1800 RPM
RATED OUTPUT - WELDER
DESCRIPTION
RATED DC OUTPUT*
DUTY CYCLE
VOLTS @ RATED AMPS
DC CURRENT RANGE
Fine Adjustment in each Range
300 Amp DC Welder
30V @ 250A
100%
All Copper Windings
40-350 Amps
Pure DC Power
NEMA Rating
32V @ 300A
60%
Generator
OUTPUT - GENERATOR
Auxiliary Power 1
3000 Watts, 60 Hz. AC
(26 Amps @ 115V), (13 Amps @ 230V)
ENGINE OPERATING LOAD
Low Idle (1360 RPM)-No Load
High Idle (1800 RPM)-No Load
AC Auxiliary-115 Volts-26 Amps
50 Amps @ 22 Volts @ 60% Duty Cycle
100 Amps @ 24 Volts @ 60 % Duty Cycle
150 Amps @ 26 Volts @ 60% Duty Cycle
200 Amps @ 28 Volts @ 60 % Duty Cycle
250 Amps @ 30 Volts @ 60 % Duty Cycle
300 Amps @ 32 Volts @ 60 % Duty Cycle
250 Amps @ 30 Volts @ 100 % Duty Cycle
FUEL CONSUMPTION
.89 gal/hr (3.37 ltrs/hr)
1.32 gal/hr (5.00 ltrs/hr)
1.42 gal/hr (5.32 ltrs/hr)
1.24 gal/hr (4.70 ltrs/hr)
1.27 gal/hr (4.82 ltrs/hr)
1.33 gal/hr (5.04 ltrs/hr)
1.47 gal/hr (5.57 ltrs/hr)
1.66 gal/hr (6.27 ltrs/hr)
1.83 gal/hr (6.91 ltrs/hr)
2.15 gal/hr (8.12 ltrs/hr)
PHYSICAL DIMENSIONS
HEIGHT
40.94** in.
1039.9 mm
WIDTH
DEPTH
24.00 in.
609.6 mm
66.91in.
1700 mm
**Top of enclosure, add 8.0” (203.2mm) for exhaust
(1) 115V will operate either 60 Hz. or 50/60 Hz. power tools, lights etc.
* Based on a 10 min. period.
CLASSIC 300G
WEIGHT
1330 lbs. (603kg.)
A-2
A-2
INSTALLATION
SAFETY PRECAUTIONS
CAUTION
WARNING
Do not attempt to use this equipment until you
have thoroughly read the engine manufacturer’s
manual supplied with your welder. It includes
important safety precautions, detailed engine
starting, operating and maintenance instructions,
and parts lists.
-----------------------------------------------------------------------ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• Insulate yourself from work and
ground
• Always wear dry insulating gloves.
-----------------------------------------------------------------------ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or
vent exhaust outside.
----------------------------------------------------------------------MOVING PARTS can injure.
• Do not operate with doors open or
guards off.
• Stop engine before servicing.
• Keep away from moving parts.
------------------------------------------------------------------------
See additional warning information at
the front of this operator’s manual.
-----------------------------------------------------------
PRE-OPERATION INSTALLATION
EXHAUST SPARK ARRESTER
Some federal, state or local laws may require that
engines be equipped with exhaust spark arresters
when they are operated in certain locations where
unarrested sparks may present a fire hazard. The
standard muffler included with this welder does not
qualify as a spark arrester. When required by local
regulations, a suitable spark arrester must be installed
and properly maintained.
CAUTION
Use of an incorrect arrester may lead to engine damage or performance loss. Contact the engine manufacturer for specific recommendations.
------------------------------------------------------------------------
LOCATION / VENTILATION
Always operate the welder with the doors closed.
Leaving the doors open changes the designed air flow
and may cause overheating.
DO NOT MOUNT OVER COMBUSTIBLE SURFACES.
Where there is a combustible surface directly under
stationary or fixed electrical equipment, the surface
shall be covered with a steel plate at least
.06”(1.6mm) thick, which shall extend not more than
5.90”(150mm) beyond the equipment on all sides.
------------------------------------------------------------------------
MACHINE GROUNDING
According to the United States National Electrical
Code, the frame of this portable generator is not
required to be grounded and is permitted to serve as
the grounding means for cord connected equipment
plugged into its receptacle.
Some state, local, or other codes or unusual operating
circumstances may require the machine frame to be
grounded. It is recommended that you determine the
extent to which such requirements may apply to your
particular situation and follow them explicitly. A
machine grounding stud marked with the symbol
is provided on the welding generator frame foot. In
general, if the machine is to be grounded, it should be
connected with a #8 or larger copper wire to a solid
earth ground such as a metal water pipe going into the
ground for at least ten feet and having no insulated
joints, or to the metal framework of a building which
has been effectively grounded. The U.S. National Code
lists a number of alternate means of grounding electrical equipment.
LIFT BAIL
A lift bail is provided for lifting with a hoist.
WARNING
• Lift only with equipment of
adequate lifting capacity.
• Be sure machine is stable
when lifting.
• Do not lift this machine using
lift bail if it is equipped with a
heavy accessory such as trailer or gas cylinder.
FALLING
• Do not lift machine if lift bail is
EQUIPMENT can damaged.
cause injury.
• Do not operate machine while
suspended from lift bail.
The welder should be located to provide an unrestricted flow of clean, cool air. Also, locate the welder so
that engine exhaust fumes are properly vented to an
outside area.
CLASSIC 300G
A-3
A-3
INSTALLATION
TRAILER (See ACCESSORY Section)
If the user adapts a non-Lincoln trailer, he must
assume responsibility that the method of attachment
and usage does not result in a safety hazard nor damage the welding equipment. Some of the factors to be
considered are as follows:
1. Design capacity of trailer vs. weight of Lincoln
equipment and likely additional attachments.
2. Proper support of, and attachment to, the base of
the welding equipment so there will be no undue
stress to the framework.
3. Proper placement of the equipment on the trailer to
ensure stability side to side and front to back when
being moved and when standing by itself while being
operated or serviced.
4. Typical conditions of use, i.e., travel speed, roughness of surface on which the trailer will be operated;
environmental conditions, likely maintenance.
5. Conformance with federal, state and local laws. (1)
(1) Consult applicable federal, state and local laws regarding specific
requirements for use on public highways.
WARNING
VEHICLE MOUNTING
Improperly mounted concentrated loads may
cause unstable vehicle handling and tires or other
components to fail.
• Only transport this Equipment on serviceable
vehicles which are rated and designed for such
loads.
• Distribute, balance and secure loads so vehicle
is stable under conditions of use.
• Do not exceed maximum rated loads for components such as suspension, axles and tires.
• Mount equipment base to metal bed or frame of
vehicle.
• Follow vehicle manufacturer’s instructions.
------------------------------------------------------------------------
When welding at a considerable distance from the
welder, be sure you use ample size welding cables.
RECOMMENDED COPPER CABLE SIZES
Cables Sizes for Combined Length
of Electrode Plus Work Cable
Amps
Duty Cycle
Up to 200 ft.
60.96 m
200 to 250 ft.
200 to76.2 m
250
100%
1
1/0
300
60%
1/0
2/0
PRE-OPERATION SERVICE
CAUTION
READ the engine operating and maintenance instructions supplied with this machine.
WARNING
• Stop engine while fueling.
• Do not smoke when fueling.
• Keep sparks and flame away
from tank.
• Do not leave unattended while
fueling.
• Wipe up spilled fuel and allow
GASOLINE fumes to clear before starting
can cause fire engine.
or explosion. • Do not overfill tank, fuel expansion may cause overflow.
GASOLINE FUEL ONLY
------------------------------------------------------------------------
OIL
This unit is supplied from the factory with the engine
crankcase filled with a high quality SAE 10W/30 oil.
This oil should be acceptable for most typical ambient
temperatures.
Consult the engine operation manual for specific
engine manufacturer’s recommendations. Upon receipt
of the welder, check the engine dipstick to be sure the
oil is at the “full” mark. DO NOT overfill.
POLARITY CONTROL AND CABLE SIZES
FUEL
With the engine off, route the electrode and work
cables through the strain relief bracket on the base
and connect to the studs located below the fuel tank
mounting rail. (See size recommendations below.)
For Positive polarity, connect the electrode cable to
the terminal marked “+”. For Negative polarity, connect the electrode cable to the “-” stud. These connections should be checked periodically and tightened
if necessary.
Fill the fuel tank with the grade of fuel recommended in
the Engine Operator’s manual. Make sure the fuel
valves on the sediment bowl and the water separator
are in the open positions.
COOLING SYSTEM
The radiator has been filled at the factory with a 50-50
mixture of ethylene glycol antifreeze and water. Check
the radiator level and add a 50-50 solution as needed
(see engine manual or antifreeze container for alternate antifreeze recommendations)
CLASSIC 300G
A-4
INSTALLATION
BATTERY CHARGING
WARNING
GASES FROM BATTERY can explode.
• Keep sparks, flame and cigarettes
away.
BATTERY ACID can burn eyes and
skin.
• Wear gloves and eye protection and
be careful when boosting, charging
or working near battery.
To prevent EXPLOSION when:
• Installing a new battery - disconnect the negative cable from the old battery first and connect
the negative cable to the new battery last.
• Connecting a battery charger remove the battery
from the welder by disconnecting the negative
cable first, then the positive cable and battery
clamp. When reinstalling, connect the negative
cable last.
• Using a booster - connect the positive lead to
the battery first, then connect the negative lead
to the ground lead on the base.
To prevent ELECTRICAL DAMAGE when:
•
•
Installing a new battery.
Using a booster.
Use correct polarity - Negative Ground.
• To prevent BATTERY DISCHARGE, if you have
an ignition switch, turn it off when engine is not
running.
• To prevent BATTERY BUCKLING, tighten nuts on
battery clamp until snug.
-----------------------------------------------------------------------The Classic 300G is equipped with a wet charged battery. The charging current is automatically regulated
when the battery is low (after starting the engine) to a
trickle current when the battery is fully charged.
When replacing, jumping or otherwise connecting the
battery to the battery cables, the proper polarity must
be observed. This system is NEGATIVE GROUND.
CLASSIC 300G
A-4
B-1
B-1
OPERATION
SAFETY PRECAUTIONS
CAUTION
WARNING
Do not attempt to use this equipment until you
have thoroughly read the engine manufacturer’s
manual supplied with your welder. It includes
important safety precautions, detailed engine
starting, operating and maintenance instructions,
and parts lists.
-----------------------------------------------------------------------ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• Insulate yourself from work and
ground
• Always wear dry insulating gloves.
-----------------------------------------------------------------------ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or
vent exhaust outside.
---------------------------------------------------MOVING PARTS can injure.
• Do not operate with doors open or
guards off.
• Stop engine before servicing.
• Keep away from moving parts.
------------------------------------------------------------------------
See additional warning information at the
front of this operator’s manual.
DO NOT MOUNT OVER COMBUSTIBLE SURFACES.
Where there is a combustible surface directly under
stationary or fixed electrical equipment, the surface
shall be covered with a steel plate at least
.06”(1.6mm) thick, which shall extend not more than
5.90”(150mm) beyond the equipment on all sides.
-----------------------------------------------------------------------The Classic 300G uses the GM 3.0L industrial watercooled gasoline engine.
RATED OUTPUT
DUTY CYCLE
250A @ 30V
300A @ 32V
100%
60%
DESIGN FEATURES
Control Panel
Both the engine and the welder controls are located on
one recessed panel at the exciter end of the machine.
The welder controls consist of a five step “Current Range
Selector” switch and a “Fine Current Adjustment” rheostat. The welder is equipped with a “Start” button, an
“Ignition” switch, an “Idler” control switch, and a “Glow
Plug” button for easier cold weather starting.
Operate the welder with the doors closed. Leaving the
doors open changes the designed air flow and can cause
overheating.
The control panel also contains an engine temperature
gauge, a battery charging ammeter, an oil pressure
gauge, two three prong grounding type receptacles and
four circuit breakers for auxiliary power.
GENERAL DESCRIPTION
All Copper Windings - For long life and dependable
operation.
The Classic® 300G is a heavy duty, engine driven, DC
arc welding power source, capable of providing constant
current output for stick welding or DC TIG welding. This
welder is wound with all copper coils, rated at 300
amps/32 Volts, and provides other Classic features such
as improved door latches and stainless hinges. With the
addition of the optional K623-1 Wire Feed Module™ the
Engine Idler Control - The Classic 300G is equipped
with an electronic automatic engine idle control. It automatically increases and decreases engine speed when
starting and stopping welding or using auxiliary
power. A built-in time delay permits changing electrodes
before the engine slows to its low idle speed. The “Idler”
control switch on the panel locks the idler in high idle
position when desired.
Classic 300G will provide constant voltage output for running the LN-7, LN-23P, or LN-25 wire feeders. The
optional K924-4 Remote Control Kit (field installed) provides a switch, or K924-5 Remote Control Kits provide a
receptacle and a remote control rheostat for remote fine
current and open circuit voltage adjustment.
The Classic 300G has an electronic Engine Protection
system. In the event of sudden low oil pressure or high
coolant temperature, the engine immediately shuts down.
The Classic 300G has a current range of 40-350 DC
amps with output ratings as follows:
These units are also capable of providing 3 kVA of
115/230 volts of 60 cycle AC auxiliary power.
Auxiliary Power - 3.0 kVA of nominal 115/230V, 60Hz,
AC. Output voltage is maintained within ± 10% at all
loads up to rated capacity. (See Optional Features for
Power Plug Kit.)
Welder Enclosure - The complete welder is rubber
mounted on a rugged steel “C” channel base.
The output terminals are placed at the side of the
machines so that they are protected by the door. The
output terminals are labeled (+) and (-).
Cranking System - A 12 volt electric starter is standard.
CLASSIC 300G
B-2
B-2
OPERATION
Air Cleaner - Heavy duty two stage dry type.
• When hauling the welder between job sites, close
the fuel feed valve beneath the fuel tank.
Muffler-A Muffler and stainless steel exhaust outlet
elbow are standard.
Engine Hour Meter - A meter to record hours of operation.
Engine Protection - The system shuts the engine
down in the event of sudden low oil pressure or high
coolant temperature. A warning light on the control
panel will indicate such a fault. To reset the engine for
restarting, turn the ignition switch off then on.
High Idle RPM (OCV) Adjustment- A potentiometer
is mounted on the output rail that allows the operator to
adjust the high idle engine speed between 1700 and
1800 RPM’S in 20 RPM increments. This is to allow
further adjustment of the OCV. Total OCV adjustment
range is about 10 Volts.
• If the fuel supply is cut off or runs out while the fuel
pump is operating, air may be entrapped in the fuel
distribution system. If this happens, bleeding of the
fuel system may be necessary. Refer to the instructions in the MAINTENANCE section of this manual.
REFER TO THE ENGINE
Operation and maintenance manual for additional
information on the engine supplied with this welder.
WELDER OPERATION
WARNING
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• Insulate yourself from work and ground.
STARTING THE CLASSIC 300G GM 3.0L
GASOLINE ENGINE
1. Turn the “IDLER” switch to “HIGH”.(Optional )
2. Turn the “IGNITION” switch to “ON”.
3. Press the Start button. When the engine starts running, release button. If the engine fails to start in 20
seconds, wait 30 seconds and repeat the above
procedure.
4. Observe the oil pressure. If no pressure shows within 30 seconds, stop the engine and consult the
engine operating manual. To stop the engine, turn
the “IGNITION” switch to “OFF”.
5. Allow the engine to run at high idle speed for several minutes to warm up. If idle control switch is left
in “Auto” position, engine will run at 1600 RPM until
engine coolant temperature reaches 130 F.
WARNING
FUMES & GASES can be dangerous.
• Keep your head out of the fumes.
• Use ventilation or exhaust to remove
fumes from breathing zone.
WELDING SPARKS can cause fire or
explosion.
• Keep flammable material away.
ARC RAYS can burn.
• Wear eye, ear, and body protection.
DUTY CYCLE
Under NO conditions should ether or other starting
fluids be used!
------------------------------------------------------------------------STOPPING THE ENGINE
The NEMA output rating of the Classic 300G is 300
amperes at 32 arc volts on a 60% duty cycle (consult
Specifications in this manual for alternate ratings).
Duty cycle is based on a ten minute period; thus, the
welder can be loaded at rated output for six minutes
out of every ten minute period.
• Turn the “IGNITION” switch to “OFF”
• At the end of each day’s welding, check the
crankcase oil level, drain accumulated dirt and water
from the sediment bowl under the fuel tank and refill
the fuel tank to minimize moisture condensation in the
tank. Also, running out of fuel tends to draw dirt into
the fuel system.
CLASSIC 300G
B-3
B-3
OPERATION
CONTROL OF WELDING CURRENT
2. In the “Auto”
operates as follows:
CAUTION
DO NOT TURN THE “CURRENT RANGE SELECTOR” WHILE WELDING because the current may
arc between the contacts and damage the switch.
-----------------------------------------------------------------------The “Current Range Selector” provides five overlapping current ranges. The “Fine Current Adjustment”
adjusts the current from minimum to maximum within
each range. Open circuit voltage is also controlled by
the “Fine Current Adjustment” permitting control of the
arc characteristics.
A high open circuit voltage setting provides the soft
“buttering” arc with best resistance to pop-outs preferred for most welding. To get this characteristic, set
the “Current Range Selector” to the lowest setting that
still provides the current you need and set the “Fine
Current Adjustment” near maximum. For example: to
obtain 175 amps and a soft arc, set the “Current
Range Selector” to the 190-120 position and then
adjust the “Fine Current Adjustment” for 175 amps.
When a forceful “digging” arc is required, usually for
vertical and overhead welding, use a higher “Current
Range Selector” setting and lower open circuit voltage. For example: to obtain 175 amps and a forceful
arc, set the “Current Range Selector” to the 240-160
position and the “Fine Current Adjustment” setting to
get 175 amps.
Some arc instability may be experienced with EXX10
electrodes when trying to operate with long arc techniques at settings at the lower end of the open circuit
voltage range.
CAUTION
DO NOT attempt to set the “Current Range Selector”
between the five points designated on the nameplate.
-----------------------------------------------------------------------These switches have a spring loaded cam which
almost eliminates the possibility of setting this switch
between the designated points.
IDLER CONTROL OPERATION
The idle is controlled by the “Idler” toggle switch on
the welder control panel. The switch has two positions
as follows:
/
position, the engine
• When welding or drawing power for lights or tools
(approximately 100-150 watts minimum) from the
receptacles, the engine operates at high idle speed.
• When welding ceases or the power load is turned off,
a preset time delay of about 10 seconds starts. This
time delay cannot be adjusted.
• If the welding or power load is not re-started before
the end of the time delay the throttle body controller
reduces the engine to low idle speed.
AUXILIARY POWER
The AC auxiliary power, supplied as a standard, has a
rating of 3.0 kVA of 115/230 VAC (60 hertz).
With the 3.0 kVA, 115/230 VAC auxiliary power, one
115V duplex and one 230V duplex, grounding type
receptacle are provided. The circuit is protected with
circuit breakers.
The rating of 3.0 kVA permits a maximum continuous
current of 13 amps to be drawn from the 230 volt
duplex receptacle. Or a total of 26 amps can be drawn
from the 115 volt duplex receptacle. The 115 volt
duplex receptacle has a configuration which permits
20 amps to be drawn from either half. The total combined load of all receptacles is not to exceed 3.0 kVA.
An optional power plug kit is available. When this kit is
specified, the customer is supplied with a plug for
each receptacle.
THROTTLE BODY DEICING SYSTEM
The welder has been designed to allow continuous
year-round operation. Engine coolant is channeled
through the Throttle Bottle Injector (TBI) housing to
prevent the build up of ice on the TBI throat around
the throttle plate. The electronic controller is programmed to automatically compensate for the build up
of ice on the throttle plate. There will be no noticeable
change in the operation of the welder should icing
develop. On start-up, there is a possibility for the
engine to overspeed ( to a maximum of 2000 RPM )
for up to 10 seconds after throttle body icing conditions have occurred.The electronic governor will correct itself for the new operating conditions and normal
operation will resume.
1. In the “High”
position, and the engine goes
to high idle speed. The speed is controlled by the governor.
CLASSIC 300G
C-1
ACCESSORIES
C-1
OPTIONAL EQUIPMENT (Field Installed)
Accessory Set (K704) - Includes 35 ft. (10.7m) electrode and 30 ft. (9.1m) work cables, headshield, work
clamp and electrode holder.
WARNING
Pipe Thawing with an arc welder can cause fire,
explosion, damage to electric wiring or to the arc
welder if done improperly. The use of an arc
welder for pipe thawing is not approved by the
CSA, nor is it recommended or supported by
Lincoln Electric.
-----------------------------------------------------------------------Power Plug Kit (K802D) - A 20 amp power plug kit
for the auxiliary power receptacles is available.
(Provides a plug for each receptacle.)
Remote Control Kit (K924-4) - Contains switch,
receptacle, remote control rheostat, and 100 ft
(30.5m) cable for adjusting the OCV at the welding
site.
Wire Feed Module (K623-1) - Provides constant
voltage (CV) output with improved arc stability for
Innershield welding. Excellent for MIG welding.
Recommended wire feeders are the LN-7, LN-23P
and LN-25.
GFCI Receptacle Kit (K1690-1) - Includes one UL
approved 115V ground fault circuit interrupter duplex
type receptacle and installation instructions. Replaces
the factory installed 115V duplex receptacle. Each
receptacle of the GFCI duplex is rated at 20 amps.
Maximum total current from the GFCI duplex is limited
to 20 amps.
TIG Module - Portable, high frequency unit with gas
valve for TIG welding. Rated at 300 amps / 60% duty
cycle. (Request Publication E3.205).
Order K930-2
Control Cable - Connects TIG Module to the Classic
300G.
Order K936-4
Trailer (K953-1) - Two-wheeled trailer with optional
fender and light package. For highway use, consult
applicable federal, state, and local laws regarding
possible additional requirements. Their is a choice of
2 hitches, a fender & a light package. Order:
K953-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-1 Fender & Light Kit.
K965-1 Cable Storage Rack
Arc Start Switch - Provides on/off control at the TIG
Module.
Order K814
Remote Control Kit (K924-5) - Contains a remote
control rheostat, and 100 ft. (30.5m) cable for adjusting the OCV at the welding site.
Water Valve Kit - For use with a water-cooled TIG
Torch. Installs inside of TIG Module.
Order K844-1
Remote Control Kit (K2464-1) - Contains a remote
control rheostat (for adjusting the CC “STICK” OCV),
remote control potentiometer (for adjusting the CV
“WIRE” OCV), and 100ft.(30.5m) cable.
K2261-1 OIL DRAIN KIT - Includes ball valve, hose
and clamp.
Contactor Kit - For use with TIG Module.
Order K938-1
Control Cable Extension - Allows the TIG Module to
be operated at distances up to 200 ft. from the power
source. Availiable length: 45 ft. (13.7m).
Order K937-45
CLASSIC 300G
D-1
D-1
MAINTENANCE
SAFETY PRECAUTIONS
• When necessary, remove the sediment bowl, if so
equipped, from beneath the fuel tank and clean out
any accumulated dirt and water.
WARNING
Have qualified personnel do the maintenance
work. Turn the engine off before working inside
the machine. In some cases, it may be necessary to remove safety guards to perform
required maintenance. Remove guards only
when necessary and replace them when the
maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.
Do not put your hands near the engine cooling
blower fan. If a problem cannot be corrected by
following the instructions, take the machine to
the nearest Lincoln Field Service Shop.
----------------------------------------------------------------------ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• Insulate yourself from work and
ground
• Always wear dry insulating gloves.
-----------------------------------------------------------------------ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or
vent exhaust outside.
-----------------------------------------------------------------------MOVING PARTS can injure.
• Do not operate with doors open or
guards off.
• Stop engine before servicing.
• Keep away from moving parts.
------------------------------------------------------------------------
See additional warning information at
front of this operator’s manual.
-----------------------------------------------------------
GENERAL INSTRUCTIONS
• Blow out the welder and controls with an air hose at
least once every two months. In particularly dirty
locations, this cleaning may be necessary once a
week. Use low pressure air to avoid driving dirt into
the insulation.
• ”Current Range Selector” contacts should not be
greased. To keep the contacts clean, rotate the current control through its entire range frequently.
Good practice is to turn the handle from maximum
to minimum setting twice each morning before starting to weld.
• Follow the engine service schedule in this manual
and the detailed maintenance and troubleshooting in
the engine manufacturer’s manual.
COOLING SYSTEM
The Classic 300G is equipped with a pressure radiator. Keep the radiator cap tight to prevent loss of
coolant. Clean and flush the cooling system periodically to prevent clogging the passage and overheating
the engine. When antifreeze is needed, always use
the permanent type. Capacity = 9.9 qts (9.4 Ltrs.).
BEARINGS
This welder is equipped with a double-shielded ball
bearing having sufficient grease to last indefinitely
under normal service. Where the welder is used constantly or in excessively dirty locations, it may be necessary to add one half ounce of grease per year. A
pad of grease one inch wide, one inch long, and one
inch high weighs approximately one half ounce. Overgreasing is far worse than insufficient greasing.
When greasing the bearings, keep all dirt out of the
area. Wipe the fittings completely clean and use clean
equipment. More bearing failures are caused by dirt
introduced during greasing than from insufficient
grease.
COMMUTATOR AND BRUSHES
WARNING
Uncovered rotating equipment can be dangerous.
Use care so your hands, hair, clothing or tools do
not catch in the rotating parts. Protect yourself
from particles that may be thrown out by the rotating armature when stoning the commutator.
-----------------------------------------------------------------------Shifting of the commutator brushes may result in:
- Change in machine output
- Commutator damage
- Excessive brush wear
Periodically inspect the commutator, slip rings, and
brushes by removing the covers. DO NOT remove or
replace these covers while the machine is running.
Commutators and slip rings require little attention.
However, if they are black or appear uneven, have
them cleaned by an experienced maintenance man
using fine sandpaper or a commutator stone. Never
use emery cloth or paper for this purpose.
• Put a drop of oil on the “Current Range Selector”
shaft at least once every month.
CLASSIC 300G
D-2
D-2
MAINTENANCE
Replace brushes when they wear within 1/4” of the
pigtail. A complete set of replacement brushes should
be kept on hand. Lincoln brushes have a curved face
to fit the commutator. Have an experienced maintenance man seat these brushes by lightly stoning the
commutator as the armature rotates at full speed until
contact is made across the full face of the brushes.
After stoning, blow out the dust with low pressure air.
To seat slip ring brushes, position the brushes in
place. Then slide one end of a piece of fine sandpaper
between slip rings and brushes with the coarse side
against the brushes. With slight additional finger pressure on top of the brushes, pull the sandpaper around
the circumference of the rings - in direction of rotation
only - until brushes seat properly. In addition, stone
slip ring with a fine stone. Brushes must be seated
100%.
Arcing or excessive exciter brush wear indicates a
possible misaligned shaft. Have an authorized Field
Service Shop check and realign the shaft.
IDLER CONTROL MAINTENANCE
PURGING AIR FROM FUEL SYSTEM ( GM
3.0L ENGINE)
WARNING
Keep fuel clear of open flames or arcs, allow
engine to cool before working on the fuel system.
Wipe up any spilled fuel and do not start engine
until fumes clear.
-----------------------------------------------------------------------The fuel system operates as follows, The fuel pump
will operate for a maximum of 3 seconds when the
ignition switch is turned “ON”. The pump will restart
once the start button is pushed and continue when the
engine starts. To purge the system of air if fuel lines
have been removed, the ignition switch can be toggled “ON” and “OFF” (at 3 second intervals) until fuel
flows through the fuel return line in the neck of the
tank.
The GM 3.0L engine does not require the system to
be bled. If the engine runs out of fuel and the tank is
refilled, the engine will restart within a few seconds if
the engine is properly tuned.
ENGINE MAINTENANCE
CAUTION
Before doing electrical work, disconnect the battery.
-----------------------------------------------------------------------When installing a new battery or using a jumper battery to start the engine, be sure the battery polarity is
connected properly. The correct polarity is negative
ground. Damage to the engine alternator and the TBI
controller can result from incorrect connection.
Refer to the engine operation and maintenance manual for additional information on the engine.
• Proper operation of the idle control requires good
grounding of the TBI controller, and battery.
• If desired, the welder can be used without automatic
idling by setting the “Idler” switch to the “High”
position.
NAMEPLATES
Whenever routine maintenance is performed on this
machine - or at least yearly - inspect all nameplates
and labels for legibility. Replace those which are no
longer clear. Refer to the parts list for the replacement
item number.
CLASSIC 300G
MAINTENANCE
D-3
D-3
ENGINE SERVICE
EVERY DAY OR EVERY 8 HOURS
FIRST SERVICE - (50 HOURS)
EVERY 100 HOURS OR 3 MONTHS
EVERY 200 HOURS OR 6 MONTHS
EVERY 600 HOURS OR 12 MONTHS
ENGINE SERVICE (NOTE 2)
MAINTENANCE ITEM
I
I
I
R
I
R
R
R
C
R
C
R
I
I
R
R
I
R
I
(
4
I
C
C
R
I
I
I = Inspect
Notes
Coolant level
Concentration of antifreeze
Radiator for contamination or blockage
Coolant (NOTE 3)
Engine oil level ( NOTE 1 )
Engine oil ( NOTE 1 & 3 )
Engine oil filter
Drain fuel bowl
Fuel filter canister
Tension of Alternator/ Fan belt
Alternator/ Fan belt wear
Alternator Belt
Fan Belt
Tighten cylinder head
Spark Plugs (Gap = 0.040)
Electrical systems
All nuts and bolts for tightness
Air filter (earlier check may be req’d)
Air filter element
Leaks or engine damage
Battery
C = Clean
TYPE OR QUANTITY
50/50 Water/Ethylene Glycol
9.9qrts, 9.4L
4.5qts, 4.3L ( including filter )
AC PF25
PSI# 32500292
Good Year 11AV0955
Good Year 11AV1220
4 - AC R46TS
Donaldson#P181050 Nelson #70206N
BCI GROUP 45
R = Replace
(1) Consult Engine Operators Manual for oil Recommendations.
(2) Consult engine operators manual for additional maintenance schedule information.
(3) Fill slowly! Ensure correct quantity is used.
(4) Clean the air filter if the engine is operating in very dusty conditions.
2/01
Above operations to be carried out by trained personnel with reference to the workshop manual where necessary.
These preventative maintenance periods apply to average conditions of operation.
If necessary, use shorter periods.
S20919-3
CLASSIC 300G
E-1
TROUBLESHOOTING
E-1
HOW TO USE TROUBLESHOOTING GUIDE
WARNING
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician and
machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical
Shock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
This Troubleshooting Guide is provided to help you
locate and repair possible machine malfunctions.
Simply follow the three-step procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM (SYMPTOMS)”. This column describes possible symptoms
that the machine may exhibit. Find the listing that
best describes the symptom that the machine is
exhibiting.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the
Possible Cause, generally it states to contact your
local Lincoln Authorized Field Service Facility.
If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your
local Lincoln Authorized Field Service Facility.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists
the obvious external possibilities that may contribute
to the machine symptom.
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts such as output
terminals or internal wiring.
ENGINE EXHAUST can kill.
• Use in open, well ventilated areas or vent exhaust
outside.
MOVING PARTS can injure.
• Do not operate with doors open or guards off.
• Stop engine before servicing.
• Keep away from moving parts.
• Remove guards only when necessary and replace when work
requiring removal is complete.
• Only qualified personnel should install, use or service this
equipment.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-2
E-2
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
POSSIBLE
CAUSES
RECOMMENDED
COURSE OF ACTION
PROBLEMS
Machine fails to hold the heat constantly.
1. Rough or dirty commutator.
2. Brushes may be worn down to
limit.
3. Field circuit may have variable
resistance connection or intermittent open circuit due to loose, or
broken wire.
4. Electrode lead or work lead connection may be poor.
5. Wrong grade of brushes may
have been installed on generator.
6. Field rheostat may be making
poor contact and overheating.
Welder starts but fails to generate
current.
1. Generator or exciter brushes may
If all recommended possible areas
be loose or missing.
of misadjustment have been
checked and the problem persists,
2. Exciter may not be operating.
Contact your local Lincoln
Authorized Field Service Facility.
3. Field circuit of generator or
exciter may be open.
4. Exciter may have lost excitation.
5. Series field and armature circuit
may be open-circuited.
Welding arc is loud and spatters
excessively.
1. Current setting may be too high.
2. Polarity may be wrong.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-3
E-3
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
POSSIBLE
CAUSES
RECOMMENDED
COURSE OF ACTION
PROBLEMS
Welding current too great or too
1. Exciter output low causing low
small compared to indication on the
output compared to dial indicadial.
tion.
2. Operating speed too low or high.
Arc continuously pops out.
1. “Current Range Selector” switch
may be set at an intermediate
position.
If all recommended possible areas
of misadjustment have been
checked and the problem persists,
Contact your local Lincoln
Authorized Field Service Facility.
FLASHING THE FIELDS:
1. Stop the engine welder and disconnect the positive battery terminal.
2. Remove the cover from the exciter.
3. Turn the “Fine Current Adjustment” (rheostat) to “100” on the dial.
4. Using a 12 volt automotive battery, connect its negative terminal to the negative brushholder. The negative
brushholder is the one nearest to the rotor lamination. See the wiring diagram. With the engine NOT running,
touch the positive battery terminal to the positive brushholder. Remove the battery from the circuit.
5. Replace the exciter cover.
6. Reconnect the positive battery cable.
7. Start the welder and the generator voltage should build up.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-4
E-4
TROUBLESHOOTING
ELECTRONIC IDLER CONTROL TROUBLESHOOTING GUIDE
Engine Will Not Return to Low
Idle in Approximately 10 Seconds
After Welding and Auxiliary Loads are Removed
Set Idler Control Switch
to the Auto Position
Check for Continuity through Idler
Control Switch
Open
Closed
Remove Molex connector
from current sensing board.
Replace Idler
Control Switch.
Operation Same
Check wiring between TBI controller and current sensing board.
Have TBI controller inspected at authorized service shop.
Machine Idlers
1. Check for current in wires looping through
current sensor.
2. Replace current sensor.
Not O.K.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-5
E-5
TROUBLESHOOTING
ELECTRONIC IDLER CONTROL TROUBLESHOOTING GUIDE
With Idler Control Switch in the AUTO Position,Engine Will Not Pick Up Speed When:
The Arc is Struck
Check for loose or disconnected
wire running between weld
selector switch and output stud.
Both
1. Check Idler circuit wiring. Possible
problems are wires from Current
Sensing Board reversed at idler
switch or wires connected incorrectly
at Current Sensor Molex plug.
2. Replace current Sensing Board.
Auxiliary Load
1. Load too small. Try load
above 150 Watts.
2. Check for loose or
disconnected wire running
from black lead out of exciter
to CB2 circuit breaker.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-6
E-6
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
Engine does not start
POSSIBLE AREAS OF
MISADJUSTMENTS(S)
RECOMMENDED
COURSE OF ACTION
1. Faulty Ignition switch
2. Insufficient charging or complete
discharge of the battery Charge.
3. Lack of fuel or air mixed in the
fuel system.
2. Clogged fuel filter.
4. Irregular and faulty fuel supply
(Injector pump trouble)
5. Moisture or carbon on spark
plugs.
6. Improper viscosity of the lubricating oil.
7. Clogged air cleaner.
8. No compression.
9. Engine protection light is ON.
Irregular running of the Engine.
1. Air mixed in the fuel system.
2. Uneven fuel injection (Faulty fuel
injector pump).
If all recommended possible areas
of misadjustment have been
3. Clogged fuel filter.
checked and the problem persists,
4. Defective governor.
Contact your local Lincoln
Authorized Field Service Facility.
5. Engine itself defective.
Engine stops running During 1. Lack of fuel in the tank.
Operation and the Engine
Protection Light Does Turn On. 2. Clogged fuel filter.
(Solid Light)
3. Air mixed in the fuel system.
4. Lack of Engine Oil.
5. Fault in oil pressure switch.
6. Oil leakage from the lubricating
system.
7. Clogged oil filter.
8. Oil too light.
9. Faulty TBI controller.
10. Faulty function of the engine.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-7
E-7
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
Engine Stops During Operation and
the Engine Protection Light Does
Turn On. (Flashing)
POSSIBLE AREAS OF
MISADJUSTMENTS(S)
RECOMMENDED
COURSE OF ACTION
1. Lack of Coolant.
2. Loose or slipping fan belt.
3. Damaged fan belt.
White or Blue Smoke.
1. Excess engine oil.
2. Too low viscosity of the engine
oil.
Dark Smoke
1. Excess injection.
2. Clogged air cleaner.
3. Faulty function of the engine.
Faulty Charging
1. Loose fan belt.
2. Faulty wiring.
3. Faulty battery.
4. Worn out alternator brush.
Starter Motor does not run.
1. Loose or damaged wiring.
If all recommended possible areas
of misadjustment have been
checked and the problem persists,
Contact your local Lincoln
Authorized Field Service Facility.
2. Low Battery voltage.
3. Damaged starter motor.
Engine Knocking.
1. Poor grade of Gasoline.
2. Spark advance to far.
Lack of Power.
1. Carbon deposits causing preignition.
2. Incorrect timing.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
E-8
E-8
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
Surging
POSSIBLE AREAS OF
MISADJUSTMENTS(S)
RECOMMENDED
COURSE OF ACTION
1. Dirty Air Filter.
2. Engine running at RPM limiter
(2000 RPM).
Large Decrease in Speed.
1. Ice build up on throttle plate.
Engine runs Irregularly.
1. Faulty coolant temperature
sender.
Engine fails to pick up speed when
Arc is struck.
1. Faulty idler circuit.
If all recommended possible areas
of misadjustment have been
checked and the problem persists,
Contact your local Lincoln
Authorized Field Service Facility.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CLASSIC 300G
B
A
THROTTLE PLATE
MOTOR
+
62
60
-
CLASSIC 300G
70
B
#
COIL
81
74
67
P8
1
2
3
4
5
6
41
600
42
602
S
W
X
SWITCH FOR LOCAL OR REMOTE CONTROL
SHOWN IN LOCAL POSITION.
B
R
R
82
OIL PRESS. G
GAUGE
S
WATER TEMP.
GAUGE
73
71
AMMETER
89
97
45
93
94
MAP SENSOR
A B C
99B
99D
77
76
SENSOR
69
SENSOR
WATER TEMP. SENDER
G
Y
G
99E
99A
SWITCH
WK
OIL PRESSURE SWITCH & SENSOR
WATER
TEMP.
SENSOR
A B
96
99
95
* * SEE BELOW
2
2
87B
3
3
4
3
2
1
G
W
REMOTE CONTROL
POTENTIOMETER BOX
B
Y
X
PLUG FOR
REMOTE CONTROL
POTENTIOMETER
87A
CONNECT
TO CASE
80
IDLER
SWITCH
G
78
AIR
TEMP.
SENSOR
A B
99C
87
50
1
1
10 K
RPM CONTROL
B
CB2
4
B
CB1
B
G
CB4
B
230 VOLT
RECEPTACLE
CONNECT TO NEG.
BRUSH HOLDER
NEGATIVE CV
OUTPUT TERMINAL
PANEL
SLIP RING
NEAREST
TO IRON
B
B
R
+
NEGATIVE
(CC-)
ALTERNATOR
AUXILIARY
POWER
WINDINGS
15A
Y
FUSE
-
AC
ROTOR
610
610
250 AMP
THERMOSTAT
ASSEMBLY
{
608
609
#2 HEAVY LEAD
#8 LEAD
1
2
3
4
5
6
-W
+Y
-W
POSITIVE
(CC+) & (CV+ WITH W.F.M.)
WELDER
LEAD BLOCK
N
U
GENERATOR
P9
U
WIRE FEED
MODULE
+Y
L11194
A.02
MACHINE MUST NOT BE RUNNING
WHEN MAKING THESE CONNECTIONS.
#2 HEAVY LEAD
NEG.
POS.
PLUG
(P5)
J8
602B
SELECTOR
SWITCH
5 4 3 21
ON MACHINE, REMOVE PLUG "P10" FROM CONNECTOR "J5".
CONNECT PLUG "P5" ON W.F.M. TO CONNECTOR "J5" ON MACHINE.
A
602A
RHEOSTAT
41
600A
42
N
12 11 10 9 8 7 6 5 4 3 2 1
600B
J5
P10
WIRE FEED MODULE (OPTIONAL)
B
W
R
Y
AC
B
ALTERNATOR
CB3
+
(GROUND SCREW
NEAR FUSE)
B
INLINE
CONNECTORS
G
W
CONTROL PANEL COMPONENTS
SHOWN AS VIEWED FROM REAR.
NEUTRAL BONDED TO FRAME
NEUTRE RACCORDE' AU BATI
SLIP RINGS
CONNECT TO POS. & NEG.
OUTPUT TERMINALS
W.F.M.
CONTROL
PANEL
CURRENT
SENSOR
G
115 VOLT
RECEPTACLE
LEAD COLOR CODE
B - BLACK
G - GREEN
N - BROWN
R - RED
U - BLUE
W - WHITE
Y - YELLOW
O - ORANGE
ELECTRICAL SYMBOLS
PER E1537
DIAGRAMS
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside
the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number..
THE RED AND BLACK LEADS ARE USED ON CLASSIC I MACHINES ONLY AND ARE NOT
CONNECTED ON THIS MACHINE. DAMAGE TO THE REMOTE CONTROL AND/OR MACHINE
WILL RESULT IF THE RED AND BLACK LEADS ARE CONNECTED IN THE CLASSIC 300G.
NEARBY, LEAVING IT UNCONNECTED.
IF NO WIRE FEED MODULE IS INSTALLED, WITH THE MACHINE OFF, DISCONNECT PLUG "P10"
ON THE MACHINE FROM CONNECTOR "J5". CONNECT PLUG "P11" FROM THE REMOTE CONTROL
KIT TO CONNECTOR "J5" ON THE MACHINE.
RESISTORS
CAUTION: DAMAGE CAN OCCUR
TO THE REMOTE CONTROL
SWITCH IF IT IS USED WITHOUT
THE "P11" PLUG INSTALLED OR A
WIRE FEED MODULE INSTALLED.
P11
12 11 10 9 8 7 6 5 4 3 2 1
MACHINE NOT RUNNING, REMOVE PLUG "P9" ON MACHINE FROM CONNECTOR "J8".
* WITH
THEN CONNECT PLUG "P8" ON REMOTE CONTROL TO CONNECTOR "J8" ON MACHINE.
A WIRE FEED MODULE IS INSTALLED, WITH THE MACHINE OFF, DISPOSE OF THE
* * IFUNCONNECTED
PLUG "P10" (IF ONE IS ON THE MACHINE) FASTEN THE NEW PLUG "P11"
SEE
* BELOW
* SEE
BELOW
97C
ENGINE
FAILURE
LAMP
51
+ EXC
-
83
91
ZENITH THROTTLE
3
BODY
4
CONTROLLER
5
WHITE
14
CONNECTOR
15
19
21
BLACK
22
CONNECTOR
1 2 3 4 5 8 9 11 12 13 17
K924-4 REMOTE CONTROL (OPTIONAL)
GROUND
TO BASE
90
92
CLASSIC 300G WIRING DIAGRAM FOR CODE 10659
ALTERNATOR
IGNITION
SWITCH
97A
CONTROL PANEL
GROUND SCREW
CB5
DISTRIBUTOR
97B
REMOTE CONTROL RECEPTACLE & SWITCH
GROUND
TO ENGINE
STARTER
MOTOR
61
ENGINE
HOUR METER
PARTS SUPPLIED
WITH ENGINE
S
84
-
INJECTOR
FUEL PUMP
+
START
72
- +
+
F-1
F-1
B
62
60
-
70
B
#
COIL
81
CLASSIC 300G
71
R
82
S
OIL PRESS. G
GAUGE
S
WATER TEMP.
GAUGE
73
51
97
AMMETER
89
ENGINE
FAILURE
LAMP
97C
91
45
93
MAP SENSOR
A B C
99B
99D
94
77
76
SENSOR
69
SENSOR
WATER TEMP. SENDER
G
99E
99A
SWITCH
WK
OIL PRESSURE SWITCH & SENSOR
WATER
TEMP.
SENSOR
A B
96
99
95
B
W
REMOTE CONTROL
POTENTIOMETER BOX
CONNECT
TO CASE
Y
X
80
IDLER
SWITCH
2
2
10 K
3
3
87B
RPM CONTROL
87A
1
1
4
3
2
1
G
4A
CB2
4
B
20A
11
CB1
INLINE
CONNECTORS
CONNECT TO NEG.
BRUSH HOLDER
NEGATIVE CV
OUTPUT TERMINAL
PANEL
CB3
B
600C
-
21A
11B
820
810
6A
21
AC
610A
ALTERNATOR
15A
+
(GROUND SCREW
NEAR FUSE)
B
CB4
B
15A
230 VOLT
RECEPTACLE
SLIP RING
NEAREST
TO IRON
B
+
67B
NEGATIVE
(CC-)
ALTERNATOR
AUXILIARY
POWER
WINDINGS
15A
21A
FUSE
-
AC
ROTOR
610
610
250 AMP
THERMOSTAT
ASSEMBLY
{
608
609
#2 HEAVY LEAD
#8 LEAD
-W
+Y
-W
POSITIVE
(CC+) & (CV+ WITH W.F.M.)
WELDER
LEAD BLOCK
N
U
GENERATOR
P8
U
WIRE FEED
MODULE
* MACHINE MUST NOT BE RUNNING
WHEN MAKING THESE CONNECTIONS.
#2 HEAVY LEAD
NEG.
POS.
PLUG
(P5)
J8
1
2
3
4
5
6
SELECTOR
SWITCH
5 4 3 21
ON MACHINE, REMOVE PLUG "P10" FROM CONNECTOR "J5".
CONNECT PLUG "P5" ON W.F.M. TO CONNECTOR "J5" ON MACHINE.
A
602A
RHEOSTAT
41
600A
42
602B
N
+Y
12 11 10 9 8 7 6 5 4 3 2 1
600B
J5
P10
WIRE FEED MODULE (OPTIONAL)
6A
GND-E
11A
G
W
CONTROL PANEL COMPONENTS
SHOWN AS VIEWED FROM REAR.
NEUTRAL BONDED TO FRAME
NEUTRE RACCORDE' AU BATI
SLIP RINGS
CONNECT TO POS. & NEG.
OUTPUT TERMINALS
W.F.M.
CONTROL
PANEL
CURRENT
SENSOR
G
11
20A
115 VOLT
RECEPTACLE
400F
LEAD COLOR CODE
B - BLACK OR GRAY
G - GREEN
R - RED OR PINK
U - BLUE
W - WHITE
Y - YELLOW
PER E1537
{
RESISTORS
G
PLUG FOR
REMOTE CONTROL
POTENTIOMETER
78
AIR
TEMP.
SENSOR
A B
87
50
99C
ZENITH THROTTLE
3
BODY
4
CONTROLLER
5
14 WHITE
15 CONNECTOR
19
21
BLACK
22
CONNECTOR
1 2 3 4 5 8 9 11 12 13 17
K924-5 REMOTE CONTROL (OPTIONAL)
GROUND
TO BASE
83
+ EXC
-
74 IGNITION
67
92
ALTERNATOR
SWITCH
97A
CONTROL PANEL
GROUND SCREW
CB5
DISTRIBUTOR
97B
90
CLASSIC 300G WIRING DIAGRAM FOR CODES 10912 AND 11135
42
41
W
Y
G
L11866
C
SWITCH FOR LOCAL OR
REMOTE CONTROL SHOWN
IN LOCAL POSITION.
602
600
X
DIAGRAMS
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside
the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number..
GROUND
TO ENGINE
STARTER
MOTOR
61
+
ENGINE
HOUR METER
PARTS SUPPLIED
WITH ENGINE
S
A
THROTTLE PLATE
MOTOR
START
84
-
FUEL PUMP
+
INJECTOR
+
72
C
.
0
1
+
F-2
F-2
F-3
F-3
DIAGRAMS
K2464-1 REMOTE CONTROL
WIRING / CONNECTION DIAGRAM
X
Y
G
B
W
CV "WIRE" CONTROL POT
CCW
RESISTORS
CC "STICK CONTROL
BLUE
RED
ORANGE
CABLE CONNECTION TABLE
REMOTE CONTROL BOX
CONNECT TO CASE
PIN
E
F
G
C
D
LEAD COLOR
RED
ORANGE
BLUE
WHITE JUMPER
WHITE JUMPER
A
S26097
CLASSIC 300G
CLASSIC 300G
CLASSIC 300G
WELDER
S10766-9
PART NO.
MOUNTING HOLES.
G
J
K
(4.00)
10.2
F
146.6
A
B
(66.91) (57.70)
170.0
C
22.1
(8.70)
D
METRIC cm (ENGLISH in.)
HOLE
SKID MOUNTING
O 1.54 (.56)
1.54 (.56) TRAILER
BUT NO FUEL.
OIL AND WATER IN ENGINE,
CENTER OF GRAVITY WITH
N.B. O
N.A.
NOTES:
A
E
58.4
(23.00)
H
E
N.B.
CONTROL PANEL
B
F
67.0
(26.38)
D
94.3
G
L
H
47.0
L
J
115.6
(20.62)
52.4
(18.50)
(45.5)
K
61.0
(24.00)
8.26
(3.25)
MOUNTING HOLE
O 1.54 (.56) SKID
(37.12)
N.A.
105.8
34.3
(13.50) (41.66)
C
(4.00)
10.2
DIMENSION PRINT
104.0
DIAGRAMS
S10766
1/03
(40.94)
F-4
F-4
WARNING
Spanish
AVISO DE
PRECAUCION
French
ATTENTION
German
WARNUNG
Portuguese
ATENÇÃO
● Do not touch electrically live parts or
● Keep flammable materials away.
● Wear eye, ear and body protection.
● Mantenga el material combustible
● Protéjase los ojos, los oídos y el
electrode with skin or wet clothing.
● Insulate yourself from work and
ground.
● No toque las partes o los electrodos
bajo carga con la piel o ropa mojada.
● Aislese del trabajo y de la tierra.
● Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
● Isolez-vous du travail et de la terre.
● Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
● Isolieren Sie sich von den
Elektroden und dem Erdboden!
● Não toque partes elétricas e elec-
trodos com a pele ou roupa molhada.
● Isole-se da peça e terra.
fuera del área de trabajo.
● Gardez à l’écart de tout matériel
inflammable.
● Entfernen Sie brennbarres Material!
cuerpo.
● Protégez vos yeux, vos oreilles et
votre corps.
● Tragen Sie Augen-, Ohren- und Kör-
perschutz!
● Mantenha inflamáveis bem guarda-
dos.
● Use proteção para a vista, ouvido e
corpo.
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE
USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.
● Keep your head out of fumes.
● Use ventilation or exhaust to
● Turn power off before servicing.
● Do not operate with panel open or
guards off.
remove fumes from breathing zone.
● Los humos fuera de la zona de res-
piración.
● Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
● Gardez la tête à l’écart des fumées.
● Utilisez un ventilateur ou un aspira-
● Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
● Débranchez le courant avant l’entre-
tien.
teur pour ôter les fumées des zones
de travail.
● Vermeiden Sie das Einatmen von
Schweibrauch!
● Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
● Mantenha seu rosto da fumaça.
● Use ventilação e exhaustão para
remover fumo da zona respiratória.
● Strom vor Wartungsarbeiten
● No operar con panel abierto o
guardas quitadas.
● N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
● Anlage nie ohne Schutzgehäuse
abschalten! (Netzstrom völlig öffnen; Maschine anhalten!)
oder Innenschutzverkleidung in
Betrieb setzen!
● Não opere com as tampas removidas.
● Desligue a corrente antes de fazer
● Mantenha-se afastado das partes
serviço.
● Não toque as partes elétricas nuas.
● Não opere com os paineis abertos
moventes.
ou guardas removidas.
WARNING
Spanish
AVISO DE
PRECAUCION
French
ATTENTION
German
WARNUNG
Portuguese
ATENÇÃO
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com