User guide | Emerson EM6000 Cordless Telephone User Manual

_
Digital Cordless Phone
Expandable
Speakerphone
Lighted Display
User Guide
EM6000
In the box
Handset
Base
Line Cord
Bracket
Expandable
Speakerphone
Lighted Display
Rechargeable
Battery
AC
Adapter
User
Guide
Getting started
Installing the battery
1. Open the battery cover.
2. Insert the battery. Be sure to
insert exactly as shown.
3. Close the battery cover.
4. Place the handset on the base
to charge.
Before using for the
first time, charge the
handset for 12-16 hours
Installing the bracket
1. Before installing the bracket, connect the line cord and AC adaptor to
the back of the base (see “Connecting”).
2. Snap the bracket to the back of the base as shown below.
3. Place the base on a flat surface.
Wall Mounting
To mount your telephone on a wall plate (not included), follow the
instructions below:
1. Plug the line cord into a modular phone jack.
2. Align the holes on the base with the mounting studs on the wall plate.
3. Pull the base down onto the studs until the telephone is secure.
wall plate
Connecting
1. Plug one end of the line cord into the jack at the back of the phone’s base,
and the other end into a modular phone jack.
line cord
modular
phone jack
insert here
Jack
AC adapter
AC Outlet
2. Connect the AC adaptor as shown above, and plug into a standard
AC outlet.
3. The handset will display “Searching”, wait until “Handset 1” is displayed.
4. Press
on the handset and confirm you hear the dial tone.
Wall Mounting
To mount your telephone on a wall plate (not included), follow the
instructions below:
1. Plug the line cord into a modular phone jack.
2. Align the holes on the base with the mounting studs on the wall plate.
3. Pull the base down onto the studs until the telephone is secure.
wall plate
The handset
Standby Screen
Using the phone
Speaker
• to use the speakerphone,
press the
button,
this can be done before
or during a call
Volume
volume screen
• during a call or while using
the speakerphone, use the
▲ and ▼ buttons to increase
or decrease the volume
Redial
• to redial a number, press and HOLD the
button,
then use the ▲ and ▼ buttons to select from a list of
recently dialed numbers, and press
redial screen
555-555-1111
555-555-2222
555-555-3333
555-555-4444
Option
to make the call
Phonebook
The phone can store up to 50 names and numbers in its phonebook.
Caller information may be saved from the received calls in the Caller ID
memory (see "Reviewing Caller ID information"), or entered manually.
Dialing a number from the phonebook:
1. Press the
button to enter the phonebook.
2. Use the ▲ and ▼ buttons to navigate up or down.
3. Press the
button to dial the selected number.
phonebook screen
John Smith
Mike Hayes
Paul Williams
Angela Dotson
Adding numbers to the phonebook:
1. Press the
open phonebook
button to enter the phonebook.
2. Press the
softkey, and select “New Entry”
from the phonebook options screen and press the
multi-press
for a,b, or c
softkey.
3. Use the handset keypad to enter a name for the entry
by multi-pressing a key until the desired letter is displayed.
4. Press
add space
to add a space and the
softkey to
go back.
5. When finished entering the name, press the
softkey.
small letters /
capital letters
6. Enter the number using the handset keypad.
7. When finished entering the number, press the
softkey.
8. Select a ring tone and press the
softkey to
save the number in the phonebook.
9. It is possible to edit and delete numbers in the
phonebook from the phonebook options screen.
phonebook screen
John Smith
Mike Hayes
Paul Williams
Angela Dotson
Option
phonebook options screen
New Entry
Edit Entry
Show Details
Delete Entry
spk
spk
Soft Keys
entry screen (name)
Name:
abc
John Smith
entry screen (number)
Number:
555-555-1234
spk
spk
Soft Keys
Menu
Use the menu to customize various settings such as ringer volume, ring
tones, language, display settings and more.
1. Press the
button to enter the menu.
2. use the ▲ and ▼ buttons to navigate from the
following selections: Phonebook, Handset, Base
Settings, Time, and Tools.
3. Press the
softkey to select an option.
4. Press the
softkey to go back.
menu screen
Phonebook
Handset
Base Settings
Time
spk
Soft Keys
Answer calls
• answer a call
• start a call
• dial a number from the phonebook or Caller ID history
End calls
• end a call
• in the menu, escape to
the standby screen
Press the
talk screen
soft key to
mute or disable mute
00:30
Mute Soft Key
spk
Caller ID / Call Waiting Caller ID
IMPORTANT: In order to use this unit’s Caller ID features, you must subscribe to
either the standard Name/Number Caller ID Service or Call Waiting Caller ID Service
from your local telephone company.
This telephone automatically displays an incoming caller’s name and telephone
number, as well as the date and time of the call. It can record and store the
information of up to 30 calls into the phone’s Caller ID memory.
Reviewing Caller ID information:
• In the standby mode, use the ▲ and ▼ buttons to
review the Caller ID history
• you can select a number and press
to dial it
• to save a number to the phonebook, press the
softkey and then select “Save Number” and press the
softkey to confirm and save
Caller ID screen
EMERSON
877-768-8483
Aug 20 12:30
New
Caller ID options screen
Save Number
Delete
Delete All
Option
spk
spk
Soft Keys
You can delete a number, or all numbers from the Caller ID history in the Caller ID
options screen
Call Waiting / Flash
The Flash feature is used to activate calling services available through your local phone
company, such as Call Waiting, and Three Way Calling. To use the features below you
must subscribe to these services from your local telephone company.
To answer an incoming call while having a conversation:
After you hear the Call Waiting tone, press and release the
button. The first call is placed on hold and the second
press to
flash
call is answered.
To return to the first call and put the second call on hold:
Press and release the
button again to return to the
first call, the second call will be put on hold.
To activate Three Way Calling:
Press and release the
button while on the first call,
you will hear a dial tone. Dial a second number, and press
the
button again to connect the two calls.
Intercom
The intercom feature is only available for cordless phone systems with
multiple handsets (see “Adding additional handsets” on the reverse side
of this user guide).
1. To use the intercom, press and HOLD the
button.
2. Dial the number of the handset you would like to call.
intercom screen
Handset 2
Jan 1 12:00
Internal_
Paging
• Press
and the handset will emit an alarm
making it easy to find
page handset
Adding additional handsets
NOTE: It is possible to register up to 4 additional handsets to the base unit
for a total of 5 handsets. If you would like to purchase additional handsets,
please contact our Customer Service department at:
1-877-768-8483 (Toll Free)
Monday – Thursday: 9AM-5PM (EST)
Friday: 9AM – 3PM (EST)
or via e-mail at:
cs@southerntelecom.com
*Includes 1 handset & base in the package,
additional handsets sold separately
Handset 1
Jan 1 12:00
Handset 2
Jan 1 12:00
Handset 3
Jan 1 12:00
Handset 4
Jan 1 12:00
Handset 5
Jan 1 12:00
Important safety instructions
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool.
2. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode. Check with local codes for
possible special disposal instructions.
Warning! The cords on this product and / or accessories contain lead, a
chemical known to the State of California to cause birth defects or other
reproductive harm. Wash hands after handling.
CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
USE ONLY WITH EMERSON MODEL NO.EM6000
SAVE THESE INSTRUCTIONS
WARNING:
TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK
The lightning flash with
arrowhead symbol, within OF ELECTRIC SHOCK, DO NOT
an equilateral triangle, is REMOVE COVER (OR BACK).
intended to alert the user NO USER SERVICEABLE PARTS
to the presence of uninsulated “dangerous voltage” INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
See marking on bottom / back of product.
The exclamation point
within the equilateral
triangle is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
Rechargeable battery warning
● This equipment contains a rechargeable battery.
● Rechargeable batteries are known to the State of California to cause cancer.
● Do not short-circuit the battery.
● The rechargeable batteries contained in this equipment may explode if
disposed of in a fire.
● Do not charge the battery used in this equipment in any charger other
than the one designed to charge this battery as specified in the owner’s
manual. Using another charger may damage the battery or cause it to explode.
Telephone jack requirements
To use this phone, you must have an RJ11C modular
telephone jack. If you do not have a modular jack,
please call your local telephone company to find out
how to get one installed.
Modular Telephone
Line Jack
Imortant installation information
● Never install telephone wiring during a lightning storm.
● Never touch uninsulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
● Use caution when installing or modifying telephone lines.
● Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
● Temporarily disconnect any equipment connected to the phone, such as
faxes,other phones, or modems.
CAUTION: Disconnect the phone cord from the
wall outlet before installing or replacing the
batteries. (Only for telephones which require
batteries)
Compliance information
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
FCC Part 68 information
1. Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US
number and Ringer Equivalence Number (REN) for the equipment. You must, upon
request, provide this information to your telephone company. The REN is useful in
determining the number of devices you may connect to your telephone line and still
have all of these devices ring when your telephone number is called. In most (but not
all) areas, the sum of the RENs of all devices connected to one line should not exceed
5. To be certain of the number of devices you may connect to your line as determined
by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your
own telephone equipment if you are on a party line. Check with your local telephone
company.
• Notice must by given to the telephone company upon permanent disconnection of
your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone
line, ensure the installation of this product does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
2. Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary discontinuance; (2)
afford you the opportunity to correct the situation; and (3) inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth in Subpart E of
Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business
and not inconsistent with FCC Rules and Regulations. If these changes are expected to
affect the use or performance of your telephone equipment, the telephone company
must give you adequate notice, in writing, to allow you to maintain uninterrupted
service.
FCC Part 15 information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
Privacy of Communications may not be ensured when using this product.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or
television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit
different from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your
dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful
booklet, “How To Identify and Resolve Radio/TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when
ordering copies.
Notice: The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF exposure information
This product complies with FCC radiation exposure limits under the following
conditions:
● The base must be placed to allow a minimum of 20cm (8 inches) between
the antenna and all persons during normal operation.
● The base must not be collocated or operated in conjunction with any other
antenna or transmitter.
● The handset is designed for body-worn operation and meets FCC RF
exposure guidelines when used with any belt clip, carrying case, or other
accessory supplied with this product. (All necessary accessories are
included in the package; any additional or optional accessories are not
required for compliance with the guidelines.) Third party accessories
(unless approved by the manufacturer) should be avoided as these might
not comply with FCC RF exposure guidelines.
Hearing Aid Compatibility
This telephone meets FCC standards for Hearing Aid Compatibility.
Information for DECT products
This telephone is compliant with the DECT 6.0 standard
which operates in the 1.92GHz to 1.93GHz frequency range.
Installation of this equipment is subject to notification and
coordination with UTAM.
Any relocation of this equipment must be coordinated
through and approved by UTAM.
UTAM may be contacted at 1-800-429-8826.
Limited Warranty
90 Days Limited Warranty
In the unlikely event that this product is defective, or does not perform
properly, you may within ninety (90) days from your original date of purchase
return it to the authorized service center for repair or exchange.
TO OBTAIN WARRANTY SERVICE:
● Provide proof of the date of purchase within the package (Dated bill of sale).
● Prepay all shipping costs to the authorized service center, and remember to
insure your return.
● Include a return shipping address (no P.O. Boxes), a telephone contact
number, and the defective unit within the package.
● Describe the defect or reason you are returning the product.
Your product will be repaired or replaced, at our option, for the same or
similar model of equal value if examination by the service center determines
this product is defective. Products received damaged as a result of shipping
will require you to file a claim with the carrier.
The shipping address of the authorized service center is:
Southern Telecom Inc.
Attention: Returns Department
14-C 53rd Street
Brooklyn, NY 11232
Should you have any questions or problems concerning this product, please
contact our customer service department at:
1-877-768-8483 (Toll Free)
Monday - Thursday: 9AM - 5PM (EST)
Friday: 9AM - 3PM (EST)
or via e-mail at:
cs@southerntelecom.com
Warranty service not provided
This warranty does not cover damage resulting from accident, misuse,
abuse, improper installation or operation, lack of reasonable care, and unauthorized modification. This warranty is voided in the event any unauthorized
person opens, alters or repairs this product. All products being returned to
the authorized service center for repair must be suitably packaged.
Limitation of Warranty:
● THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE
TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED
(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED.
● REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE EXCLUSIVE REMEDY OF THE CONSUMER. SOUTHERN TELECOM
INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING
OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY
ARE GOVERNED BY THE LAWS OF THE STATE OF NEW YORK.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts so the
above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you also may have other rights that vary from state
to state.
Distributed by: AIT, Inc. Brooklyn NY 11232
© 2010 All rights reserved
Emerson and the G-Clef logo are registered trademarks of
Emerson Radio Corp. Parsippany, New Jersey USA
Download PDF

advertising