Owner`s manual | Emerson EWC0901 TV VCR Combo User Manual

T4259.QX33
00.11.28 6:48 PM
Page 1
OWNER’S
MANUAL
9-INCH COLOR TV/VCR
EWC0901
This Owner’s Manual is made of
recycled paper.
As an ENERGY STAR ®
Partner, our company has
determined that this product meets
the ENERGY STAR ® guidelines for
energy efficiency. ENERGY STAR ® is
a U.S. registered mark.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
TOLL FREE : 1-800-256-2487.
Please read before using this equipment
T4259.QX33
00.11.28 6:48 PM
Page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV/VCR and to protect it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the
TV/VCR on a bed, sofa, rug, or other similar surface. This
TV/VCR should never be placed near or over a radiator or
heat register. This TV/VCR should not be placed in a builtin installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions
have been adhered to.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug TV/VCR from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by
the TV/VCR manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/VCR near waterfor example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool,
and the like.
8.Accessories-Do not place this TV/VCR on an unstable cart,
stand, tripod, bracket, or table. The TV/VCR may fall, causing serious injury to someone, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufac- PORTABLE CART WARNING
turer, or sold with the TV/VCR. Any
mounting of the appliance should
follow the manufacturer’s instructions and should use a mounting
accessory recommended by the manufacturer. An appliance and cart
combination should be moved with
S3126A
care.
10.Power Sources-This TV/VCR should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For TV/VCRs intended to operate from battery
power, or other sources, refer to the operating instructions.
11.Grounding or Polarization-This TV/VCR is equipped
with a polarized alternating-current line plug(a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
-2-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 3
F IGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECT RICAL CODE
ANTE NNA
L EAD I N
WI RE
GROUND
CLAMP
A NTENNA
DI SCHARG E UN I T
(NEC SECTION 8 10 -2 0)
EL ECT RI C
SE RV I CE
EQ U I PM EN T
G RO UNDI NG CO NDUCT ORS
(NEC SECTION 8 10 -2 1)
G RO UND CL AM PS
NEC - NATI O NAL EL ECTRI CAL CO DE
POWER SERVI C E G RO UNDI NG
EL EC TR O DE SYST EM
(NEC ART 2 50 , PART H)
S2 8 9 8 A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/VCR, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/VCR receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the TV/VCR due to lightning and
power-line surges.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/VCR through openings as they may touch dangerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
the TV/VCR.
19.Damage Requiring Service-Unplug this TV/VCR from
the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/VCR.
c. If the TV/VCR has been exposed to rain or water.
d. If the TV/VCR does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV/VCR to its normal operation.
e. If the TV/VCR has been dropped or damaged in any way.
f. When the TV/VCR exhibits a distinct change in performance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to
this TV/VCR, ask the service technician to perform routine
safety checks to determine that the TV/VCR is in proper
operating condition.
22.Heat-This TV/VCR product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/VCR yourself
as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
-3-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 4
PRECAUTIONS
LOCATION
For safe operation and satisfactory performance of
your TV/VCR, keep the following in mind when
selecting a place for its installation:
• Shield it from direct sunlight and keep it away
from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
at the top and bottom of the unit. Do not place the
unit on a carpet because this will block the ventilation holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the TV/VCR near strong magnetic fields.
• Avoid moving TV/VCR to locations where temperature differences are extreme.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting
•
•
•
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/VCR cassette holder.
Do not place anything directly on top of the unit.
WARNING
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a tape is played in a TV/VCR
which has moisture, it may damage the tape and
TV/VCR. Therefore when the condensation occurs
inside the unit, “DEW” appears on the screen. In this
case, turn the POWER button on and allow at least 2
hours for the unit to dry out.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright
laws. We assume no responsibility for the unauthorized duplication, use, or other acts which infringe
upon the rights of copyright owners.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial
number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
-4-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 5
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
AVOID THE HAZARDS OF ELECTRICAL
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6
C OPERATING CONTROLS AND FUNCTIONS 7
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9
ANTENNA/CABLE CONNECTIONS . . . . . . .9
INSTALLING THE BATTERIES . . . . . . . . . . .10
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10
MOBILE CONNECTION . . . . . . . . . . . . . . . .10
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11
CHANNEL SET UP FOR THE FIRST TIME . .11
CLOCK SET UP (AUTO / MANUAL) . . . . . .12
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .13
DELETING (OR ADDING) CHANNEL . . . . .13
SELECTING THE LANGUAGE . . . . . . . . . . .14
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .14
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15
WATCHING A TV PROGRAM . . . . . . . . . . . .15
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .15
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .16
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .16
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .16
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .17
PICTURE CONROLS . . . . . . . . . . . . . . . . . . .18
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .18
NORMAL RECORDING . . . . . . . . . . . . . . . . .19
SKIPPING UNWANTED SCENES DURING
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19
OTR (One Touch Recording) . . . . . . . . . . . . . .19
TIMER RECORDING . . . . . . . . . . . . . . . . . . .20
TIMER PROGRAM EXTENSION . . . . . . . . .31
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .22
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .22
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .23
C COPYING A VIDEO CASSETTE . . . . . . . . . .28
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .24
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .24
REAL TIME TAPE COUNTER . . . . . . . . . . . .24
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .24
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .24
C TROUBLESHOOTING GUIDE . . . . . . . . . . .25
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .26
C CABLE CHANNEL DESIGNATIONS . . . . . .26
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover
INDICE
CONTROLES DE OPERACIÓN Y
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .29
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30
CONEXIONES DE ANTENA/CABLE . . . . . . . .30
PREPARACIÓN DE CANALES POR
PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
-5-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 6
FEATURES
• Infrared remote control
• Dew Sensor–Indicates that moisture condensation may
• Still–“Freeze” the picture at any time, for close viewing
• Bilingual on screen menu display selectable in
•
occur inside the TV/VCR.
•
English or Spanish
Real time counter–This shows the elapsed recording or
•
playback time in hours, minutes, and seconds. The “–”
indication will appear when the tape is rewound further
than the tape counter position “0:00:00”.
•
• 181 channel capability PLL frequency synthesizer
•
tuner with direct station call–(A converter may be nec-
essary to view scrambled cable channels.)
• Auto Clock Setting–Allows you to set the clock function
•
•
•
•
from a PBS broadcast station.
Game mode–Automatically sets external input mode and
allows TV/VCR display to be suitable for use with TV
games.
Auto power on and off system–Automatically turns on
the TV/VCR when you insert the cassette, turns off after
auto-rewind, and ejects when the beginning of the tape is
reached.
Auto rewind when the end of a tape is reached–This
function doesn’t occur when using timer recording.
2 Step picture search operation–You can view a video
program at a high speed or super high speed in either a
forward or reverse direction in LP and SLP mode. For
SP mode only high speed.
• Three different playback tape speeds : SP/LP/SLP
• Two different recording tape speeds : SP/SLP
• Auto Head Cleaner–Automatically cleans video heads as
•
of a particular scene. Only tapes recorded in SLP mode
will show a fairly clear picture.
Digital Auto Tracking (DTR)–Automatically adjusts the
tracking for each tape you play.
Rental play mode–Improves playback picture quality
from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a tape
indefinitely without pressing the PLAY button.
Time search–Let you set the TV/VCR to advance the
tape by entering the desired playback time you want to
skip.
OTR (One Touch Recording)–Instant timed recording
from 30 to 480 minutes is possible at the push of the
REC/OTR button.
• 1 Year, 8 events (including Daily and Weekly Timer
•
•
•
•
you insert or remove a cassette.
Recording)–The built-in timer allows you to record up
to 8 programs at different times on different channels up
to 1 year in advance. The Daily timer allows recordings
to be made of daily broadcasts, and the Weekly timer
allows recording to be made once a week up to the end
of the tape.
Auto return–After timer recording is finished, the
TV/VCR can return to the beginning of the recording.
Wake up/Sleep timer–Allows you to have the TV/VCR
automatically turn on or off at a desired time.
Timer Program Extension–Allow you to shift the time
schedule for automatic timer recording.
Two- way power–Allows you to power the TV/VCR
with standard household AC or your vehicle’s battery,
using the supplied car-battery cord.
• Zero Return–The tape returns to counter of 0:00:00 by
rewinding or fast forwarding.
SUPPLIED ACCESSORIES
Remote Control Unit
Dipole Antenna
Matching Adapter
(300ohm-75ohm)
(1813641/1780103)
2 AA
Batteries
PART NO. (N0107UD)
(0EMN00723)
Car Battery Cord
WPZ0202GA004
AC Cord
WAV0182NW001/WAV0182LW001
• If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800256-2487.
• Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control. If you decide to use a universal remote control with this unit, please be aware
that the code number given may not operate this unit. In this case, please call the manufacturer of the universal remote control.
-6-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 7
OPERATING CONTROLS AND FUNCTIONS
NOTE:
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- TV/VCR FRONT PANEL - [Fig.1]
AUDIO
POWER
VIDEO
STOP/EJECT rREW
PLAY
F.FWDq REC/OTR
VOLUME
6 7 8 9 10
11
CHANNEL
EARPHONE
REC
1 2
3 4 5
12
13 14
Fig.1
- REMOTE CONTROL - [Fig.2]
25
WAKE-UP
/SLEEP
POWER
5
15
16
17
7
CHANNEL
RETURN
1
2
3
4
5
6
7
8
9
0
+100
MENU
DISPLAY
MUTE
CHANNEL
19
20
VOLUME
PLAY
REW
F.FWD
6
24
12
11
23
8
9
STOP
6
10
18
EJECT
RECORD
T-PROG.
CLEAR
COUNTER
RESET
SPEED
PAUSE/STILL
GAME
TIME SEARCH
22
21
Fig.2
1 AUDIO input jack– Connect to the audio output
jack of your audio equipment, video camera or
another VCR.
2 VIDEO input jack– Connect to the video output
jack of your video camera or another VCR.
3 RECORD indicator– Flashes during recording.
Lights up in the Stand-by mode for Timer
Recording.
4 Remote Sensor Window– Receives the infrared
signals from the remote control.
5 POWER button– Press to turn TV/VCR on and off.
Press to activate timer recording.
6 STOP button– Press to stop the tape motion.
EJECT button– Press in the Stop mode to remove
tape from TV/VCR.
L button–
• Press to select setting modes from the on screen
menu.
• Press to enter digits when setting program.
(for example: setting clock or timer program)
7 REW button– Press to rew¨ind the tape, or to view
the picture rapidly in reverse during playback
mode. (Rewind Search)
s button–
• Press to select a mode from a particular menu.
(for example: LANGUAGE or USER’S SET UP)
8 PLAY button– Press to begin playback.
K button–
• Press to select setting modes from the on screen
menu.
• Press to enter digits when setting program.
(for example: setting clock or timer program)
-7-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 8
- REAR VIEW - [Fig.3]
27
DC 13.2V
AC 120V
28
ANT
Fig.3
26
9 F.FWD button– Press to rapidly advance the tape,
125, first press the “+100” button then press “2”
or to view the picture rapidly in forward during
and “5”).
playback mode. (Forward Search)
16 MENU button– Press to display the main menu on
B button–
the TV screen.
17
When
setting
program
(for
example:
setting
clock
DISPLAY button– Display the counter or the cur•
or timer program), press to determine your selecrent channel number and current time on the TV
tion and proceed to the next step you want to
screen. (See page 17.)
input.
18 SPEED button– Press to choose the desired
recording speed:SP/SLP.
• Press to determine setting modes from on screen
menu.
19 T-PROG. CLEAR button– Press to cancel a setting
of timer program. (See page 25.)
• Press to select a mode from a particular menu.
(for example: LANGUAGE or USER’S SET UP)
COUNTER RESET button– Press to reset counter
to 0:00:00.
10 REC button– Press for manual recording.
OTR button– Activates One Touch Recording.
20 GAME button– Sets the game mode and external
(only on the TV/VCR)
input mode at the same time. (See page 18.)
11 VOLUME X / Y buttons– Adjust the volume
21 TIME SEARCH button– Press to activate Time
level.
Search mode.
12 CHANNEL K / L buttons– Press to select the
22 PAUSE/STILL button– Press to temporarily stop
desired channels for viewing or recording.
the tape during the recording or to view a still picture during playback.
You may display the main menu on the TV screen
by pressing repeatedly this button on the
23 MUTE button– Mutes the sound. Press it again to
TV/VCR.
resume sound.
TRACKING function– Press to minimize video
24 CHANNEL RETURN button– Press to go back to
‘noise’ (lines or dots on screen) during playback
the previously viewed channel. For example,
mode. (See page 19.)
pressing this button once will change channel display from 3 (present channel) to 10 (previously
13 EARPHONE jack– Connects to earphones (not
viewed channel), and pressing it a second time
supplied) for personal listening. The size of jack is
will return from 10 to 3.
1/8” monaural (3.5mm).
25 WAKE UP/SLEEP button– Sets the Wake up or
14 Cassette compartment
Sleep Timer. (See page 26.)
15 Number buttons– Press to select desired channels
26 ANT. terminal– Connect to an antenna or cable
for viewing or recording. To select channels from
system.
1 to 9, first press the 0 button and then 1 to 9.
27 DC 13.2V jack– Connect to the Car Battery Cord.
+100 button– When selecting cable channels
28 AC 120V jack– Connect to the AC cord.
which are higher than 99, press this button first,
then press the last two digits. (To select channel
-8EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 9
PREPARATION FOR USE
From Cable System or
Satellite Dish
Satellite Box or
OUT
Cable Box
IN
(Not supplied)
Dipole Antenna
(Supplied)
VHF/UHF Antenna
(Not supplied)
Flat twin-lead cable
VHF Antenna
(Not supplied)
From
Cable System
UHF Antenna
(Not supplied)
or
DC 13.2V
AC 120V
ANT
VHF/UHF
or Combiner
(Not supplied)
75-ohm Coaxial
Cable (Not
supplied)
or
ANT.
or
Flat twin-lead cable
Fig.4
VHF/UHF COMBINED ANTENNA
ANTENNA/CABLE
CONNECTIONS
A VHF UHF 75 ohm combination antenna can be
connected to ANT terminal.
DIPOLE ANTENNA HOOK UP
VHF/UHF SEPARATE ANTENNAS
1. Push the stem of the Dipole Antenna (accessory)
into the hole for antenna at the back of TV/VCR.
2. Connect the flat twin-lead cable from the Dipole
Antenna to the 300/75 ohm Matching Adapter
(accessory).
3. Plug the Matching Adapter to ANT terminal of
TV/VCR as shown in drawing.
For the best reception, extend the Dipole Antenna
and adjust its length and position. (Avoid handling
the top section when making adjustments).
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
NOTE: If it is difficult to get good reception with
the indoor antenna, the use of an outdoor antenna is
recommended. Before an outdoor antenna is connected to the set, the indoor antenna should be disconnected.
Use this connection if your cable system connects
directly to your TV/VCR without a converter box.
By using this connection you can:
1) Use the TV/VCR remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This unit will ONLY record and view the
same channel.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
Antenna/Cable Connections Continued on the Next Page.
-9-
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 10
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
MOBILE CONNECTION
WARNING: The driver should never watch
the TV/VCR while operating a motor vehicle.
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown here.
By using this connection you can also record scrambled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/VCR Remote Control. Unattended timer recording is limited to one channel at a time.
CAUTION: If you use the TV/VCR with the
vehicle’s engine off, recharge the vehicle’s
battery after about every 4 hours of use to
prevent it from running down. After you finish using the TV/VCR be sure you unplug the
car-battery cord from the cigarette-lighter
socket.
TO RECORD A SCRAMBLED/UNSCRAMBLED
CHANNEL
1. Set the TV/VCR channel selector to the output
channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
1) The supplied indoor antenna is adequate when
your vehicle is stationary. For best reception on
the road, use a high-quality VHF/UHF mobile TV
antenna.
2) Attach the car battery cord to the DC13.2V connector on the back of the TV/VCR. Then, connect
the other end to your vehicle’s cigarette-lighter
socket.
NOTES:
• Be sure your vehicle has a 13.2-volt, negativeground electrical system.
• Be sure you use only the supplied car battery cord.
Using another cord could damage the TV/VCR.
• Be sure the socket is free of ashes and other debris.
• Be sure to push the car battery cord’s plug completely into the cigarette-lighter socket.
• Always unplug the car battery from the cigarettelighter socket before you unplug it from the
TV/VCR.
• You must disconnect the car battery cord from the
TV/VCR before you can use the AC power.
• Be sure to replace the fuse with only the same
type, 5A, 250V.
To the vehicle's
cigarette-lighter socket
VHF/UHF Combination
Mobile Antenna
(Not supplied)
EXTERNAL INPUT MODE
When using an external input signal (another VCR or
video camera), connect the player’s audio/video output cables to the AUDIO IN/ VIDEO IN jacks of
your TV/VCR. Then press the CHANNEL K or L
button until “AUX” appears on the screen.
Car battery cord
(Supplied)
ANT.
DC13.2V
AUX
[Fig.8]
- 10 -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 11
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then
select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1
TO SELECT ADESIRED CHANNEL
You can select the desires channel by using the
CHANNEL K or L button on or directly pressing
the number buttons on the remote control.
Note for using the number buttons:
• When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last tw odigts. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
• You must procede single-digit channel numbers
with a zero (Example: 02 ... 09).
Plug in the TV/VCR power cord
Attach the smaller end of the supplied AC cord to the AC 120V
connector on the back of the
AC 120V
TV/VCR. Then, plug the other
end into a standard AC outlet.
NOTES:
• You must disconnect the car battery cord from the
TV/VCR before you use AC power.
• If some digits appear in the corner of the screen,
press the POWER button without unplugging the
power cord.
2
CLOCK SET UP
(AUTO / MANUAL)
Turn on the TV/VCR
Set the clock accurately for proper automatic timer
recording. If the Public Broadcasting Station (PBS)
is available in your area, follow “AUTO CLOCK
SETTING”. If it is not, follow “MANUAL CLOCK
SETTING”.
Press the POWER button to turn on the TV/VCR.
3
Select “ENGLISH” or “ESPAÑOL”
Select “ENGLISH” or
“ESPAÑOL”=Spanish using the
F.FWD/B or REW/s button. “[ ]”
indicate the selected language.
4
– SET UP –
B LANGUAGE
[ENGLISH] ESPAÑOL
AUTO CLOCK SETTING
AUTO PRESET
Begin auto preset
– SET UP –
Press the PLAY/K or STOP/L button to point to “AUTO PRESET”.
Then press the F.FWD/B button.
The tuner scans and memorizes all
active channels in your area.
NOTES:
• The TV/VCR distinguishes between standard TV
channels and cable channels.
• If you want to play or record a video tape BEFORE
presetting the tuner, you must press the MENU button on the remote control. To preset the tuner again,
see “CHANNEL SET UP AGAIN” on page 14.
• The TV/VCR may recognize TV channels to be
CATV channels by the receiving conditions. In this
case, try auto preset again in the fine receiving
conditions.
LANGUAGE
[ENGLISH] ESPAÑOL
B AUTO PRESET
5
You can have the TV/VCR set the clock automatically by using the Public Broadcasting Station (PBS)
channel in your area. Once you have set the clock by
using the following procedure, the TV/VCR will
automatically monitor the correct time and date
being broadcast by the PBS station in your area,
using a new service called Extended Data Service
(XDS).
Make sure ...
• TV/VCR power must be turned on.
• Confirm that the antenna connections are correct.
• The cable converter box must be turned on if your
TV/VCR is connected directly to it. (See NOTES:)
• The channel is properly set in advance.
After scanning
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote
control number buttons or CHANNEL K or L.
- 11 -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 12
NOTES:
• Auto clock setting only needs to be set once. But it
can be done again if the clock’s time has become
incorrect for some reason.
• If the TV/VCR is connected directly to a cable
converter box or satellite box, the local PBS station
must be selected on the cable box itself, and the
TV/VCR must be set to the output channel of the
cable converter box or satellite box (usually channel 3 or 4), to be able to set up or correct the clock
automatically.
If you do not know what your local PBS station is,
then follow “Manual Clock Settings”.
The TV/VCR cannot control the channels of the
cable converter box or satellite box.
1
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
2
Set “AUTO CLOCK” to [ON]
Press the F.FWD/B or REW/s
button repeatedly until [ON]
appears.
3
If you choose [AUTO],
• The TV/VCR must search until the PBS channel is
found. It must scan each channel for a couple of
seconds to determine if that channel is transmitting
the XDS signal.
• If the time, that is automatically set by this selected PBS station is incorrect, it may not be your
local PBS station, but one from a different time
zone. Or there is a case that no channel is broadcasting the XDS signal in your area, as shown by
no time. In these cases, you must manually enter
the correct local PBS station, or set the clock manually and turn off the Auto Clock Setting feature.
MANUAL CLOCK SETTING
Make sure ...
• TV/VCR power must be turned on.
In the example below, the clock is to be set to:
DATE
May 1st, 2001
SETTING TIME 5:40PM
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
1
– SETTING CLOCK –
B AUTO CLOCK
AUTO CLOCK CH
[ON]
[AUTO]
MANUAL CLOCK SET
D.S.T.
[OFF]
2
Enter the channel number for the PBS station
Press the PLAY/K or STOP/L button to point to
“AUTO CLOCK CH”.
Then press the F.FWD/B or
REW/s button until the channel
number for your local PBS station
appears.
If you do not know the PBS channel number, leave it
set to [AUTO] which is located before [2]. The
TV/VCR will search automatically all available channels for the local PBS station, and will select that
channel.
– SETTING CLOCK –
AUTO CLOCK
B AUTO CLOCK CH
[ON]
[AUTO]
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
Select “MANUAL CLOCK SET”
Press the PLAY/K or STOP/L button to point to “MANUAL CLOCK
SET”.
Then, press the F.FWD/B button.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
B MANUAL CLOCK SET
D.S.T.
[OFF]
MANUAL CLOCK SET
D.S.T.
4
[OFF]
Select the month
– MANUAL CLOCK SET –
MONTH DAY
05 / ––
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
Exit the Auto Clock Setting
4
Press the MENU button on the remote control to
return to TV mode.
5
3
Press the PLAY/K or STOP/L button until your desired month
appears. (Example: May → 05)
Then, press the F.FWD/B button.
Turn off the TV/VCR
Turn the TV/VCR off. Because the Auto Clock functions automatically while the TV/VCR is off.
Select the day
Press the PLAY/K or STOP/L button until your desired day appears.
(Example: 1st → 01)
Then, press the F.FWD/B button.
- 12 -
– MANUAL CLOCK SET –
MONTH DAY
05 / 01
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
EN
9J27
T4259.QX33
5
00.11.28 6:48 PM
Page 13
Select the year
Press the PLAY/K or STOP/L button until your desired year appears.
(Example: 2001)
Then, press the F.FWD/B button.
05 / 01
HOUR
Make sure ...
• Press the POWER button to turn on the TV/VCR.
2001
––
1
MONTH DAY
05 / 01
HOUR
YEAR
TUE
2001
MINUTE
PM
Select the minute
Press the PLAY/K or STOP/L button until the desired minute appears.
(Example: 40)
Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “CHANNEL SET
UP”.
Then, press the F.FWD/B button.
– MANUAL CLOCK SET –
05 : ––
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
– MANUAL CLOCK SET –
MONTH DAY
05 / 01
HOUR
2
YEAR
TUE
2001
Begin auto preset
Press the PLAY/K or STOP/L button to point to “AUTO PRESET”.
Then, press the F.FWD/B button.
The tuner scans and memorizes all
the active channels in your area.
MINUTE
05 : 40
8
TUE
Select the hour
Press the PLAY/K or STOP/L button until your desired hour appears.
(Example: 5, PM)
Then, press the F.FWD/B button.
7
YEAR
MINUTE
–– : ––
6
CHANNEL SET UP AGAIN
– MANUAL CLOCK SET –
MONTH DAY
PM
Start the clock
Press the MENU button on the
remote control.
Although seconds are not displayed,
they begin counting from 00 when
you press the MENU button on the
remote control. Use this feature to
synchronize the clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 30 seconds, you may have to
reset the clock.
– CHANNEL SET UP –
ADD / DELETE CH (TV)
B AUTO PRESET
5:40 PM
3
After scanning
The tuner stops on the lowest memorized channel.
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
TO CHANGE CLOCK SETTING
1
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the
F.FWD/B or REW/s button.
3)Enter correct numbers using the PLAY/K or
STOP/L button.
4)Press the MENU button on the remote control to
start the clock.
Select “CHANNEL SET UP”
Press the MENU button on the
remote control. Then press the
PLAY/K or STOP/L button to
point to “CHANNEL SET UP”.
Then, press the F.FWD/B button.
2
PLEASE NOTE:
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and press
the F.FWD/B or REW/s button to turn [OFF] this
function. Then you can manually adjust the clock.
Select “ADD/DELETE CH”
Press the PLAY/K or STOP/L button to point to “ADD/DELETE
CH”.
Press the F.FWD/B button.
3
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
Enter the desired channel number
Press the PLAY/K or STOP/L button until your desired channel number appears. (You can also use the
number buttons or the CHANNEL
K/L button to enter it) (Example:
CH8)
- 13 -
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
08
ADD / DELETE
EN
9J27
T4259.QX33
4
00.11.28 6:48 PM
Page 14
DAYLIGHT-SAVING TIME
Delete (or add) it from (into) memory
Press the F.FWD/B or REW/s button. The channel
number changes to light red. The channel is deleted
from memory.
• To delete another channel, repeat steps [3] and [4].
• If you press the F.FWD/B or REW/s button
again, the channel is memorized again.
Added channel: Light blue.
Deleted channel: Light red.
5
Exit the channel setup mode
Press the MENU button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL K or L button.
SELECTING THE LANGUAGE
Make sure ...
• Press the POWER button to turn on the TV/VCR.
NOTE: This function effects only the language on
the screen menu and not the audio source.
1
Select “LANGUAGE”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “LANGUAGE”.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
Select this feature and the TV/VCR’s clock automatically will advance one hour in April, then reverse one
hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
• First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
• Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
• Press the POWER button to turn on the TV/VCR.
1
2
2
Select “ENGLISH” or “ESPAÑOL”
3
Exit the Language mode
Press the MENU button on the remote control to
return to TV mode.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the PLAY/K or STOP/L button to point to “D.S.T.”.
Then, press the F.FWD/B or
REW/s button until [ON] appears.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH
[AUTO]
MANUAL CLOCK SET
B D.S.T.
3
Select “ENGLISH” or “ESPAÑOL”= Spanish using
the F.FWD/B or REW/s button.
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
[ON]
Exit the Daylight-Saving Time mode
Press the MENU button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
F.FWD/B or REW/s button.
NOTE: If for some reason the menu is in Spanish,
press the MENU button on the remote control, press
the PLAY/K button to point to “IDIOMA
[ESPAÑOL]”, then press the F.FWD/B button, then
press the MENU button on the remote control.
- 14 -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 15
TV OPERATION
WATCHING A TV PROGRAM
1
PICTURE CONTROL
Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR.
2
Select the channel number
Press the CHANNEL K or L button to select your
desired channel number or press the number buttons
on the remote control.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be viewed must be selected
on the cable box or satellite box.
3
The TV/VCR’s picture controls – BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
• Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
• When setting the Picture Control, the Game mode
will be cancelled.
Make sure ...
• TV/VCR power must be turned on.
1
Adjust sound
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to ”PICTURE CONTROL”.
Then, press the F.FWD/B button.
Press the VOLUME X or Y button
to adjust the volume.
VOLUME
Select “PICTURE CONTROL”
20
C C C C C CCCCCCC
–MENU–
TIMER PROGRAMMING
B PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
GAME MODE
This function enables you to decrease the TV screen
contrast and making it suitable for use with a TV
GAME.
NOTE: This function can not be set during recording.
Press the GAME button on the
remote control. “GAME” appears
on the screen.
GAME
When you press the GAME button;
• The TV/VCR comes on automatically if it is off.
• The TV/VCR will be in external input mode automatically.
2
Select item you want to adjust
Press the PLAY/K or STOP/L button until desired control is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
3
BRIGHT
–PPPPPPPCPPPPPPP+
Adjust the picture control
Press the F.FWD/B or REW/s button to adjust to
your desired level.
TO CANCEL THE GAME MODE
COLOR
REW/s
to decrease
brightness
to decrease
contrast
to pale
F.FWD/B
to increase
brightness
to increase
contrast
to brilliant
TINT
SHARPNESS
to purple
to soft
to green
to clear
BRIGHT
Press the GAME button or CHANNEL K or L button on the remote control.
CONTRAST
DEGAUSSING
Magnetism from nearby appliances might affect the
color of the TV picture.
If this happens, move this unit away from the appliance. If the color is still not correct, disconnect
power cord from AC outlet then reconnect it after 30
minutes.
• If there is a power failure of any kind, the unit will
- 15 -
retain its memory for this feature.
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 16
PLAYBACK
This TV/VCR will operate with any cassette that has the
mark. For best results, we
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
INSERTING A CASSETTE
AUTO REPEAT PLAYBACK
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/VCR. The
TV/VCR will automatically turn on.
The TV/VCR has the auto repeat function that allows
you to repeat a tape indefinitely without touching the
PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
Window
CORRECT
WRONG
1
PRECAUTIONS
• Avoid moisture. Moisture condensation may occur
•
•
•
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/VCR, wait until the tape has warmed to
room temperature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
NORMAL PLAYBACK
1
Select “ALL” or “BLANK”
– USER’S SET UP –
RENTAL
B REPEAT PLAY
AUTO RETURN
[OFF]
[ALL]
[OFF]
Exit the Repeat Play setting
Insert a prerecorded tape
To begin playback
PLAY B
Press the PLAY button.
3
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
Press the MENU button on the remote control to
return to the TV mode.
If the erase-protection tab has been removed, the
TV/VCR will start playback automatically.
2
2
Press the PLAY/K or STOP/L button to point to “REPEAT PLAY”.
Press the F.FWD/B or REW/s
button repeatedly until your desired
selection [ALL] or [BLANK]
appears.
3
Make sure ...
• TV/VCR power must be turned on.
Select “USER’S SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
To stop playback
Press the STOP button when playback is completed.
STOP
4
Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
• Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/VCR.
• If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
- 16 -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 17
SEARCH
PICTURE SEARCH
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button. (in the SP / LP / SLP
modes)
2)Press it again and the TV/VCR will now search in
super high speed. (in the LP / SLP modes only)
NOTE: Tapes recorded in the SP or LP mode will
display a noise bar on the TV screen and the picture may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
ZERO RETURN
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2
Reset the counter to 0:00:00
Press the COUNTER RESET button repeatedly.
3
NOTES:
• Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
• This function will not operate in recording mode.
In the example below: To watch a program after 2
hour 50 minutes from the present position, in either
direction.
1
Insert a tape.
2
Select “TIME SEARCH” mode
Press the TIME SEARCH button (with each push it
will increase by 10 minute).
3
Enter your desired time
TIME SEARCH
2 : 50
Press the PLAY/K or STOP/L button until your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time Search at this point,
press the MENU button on the remote control.
4
Begin Time Search
By pressing the REW/s or F.FWD/B button, the
TV/VCR will rewind or fast forward to the specified
point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the TV/VCR or the
remote control. This will delete the selected time.
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
STILL PICTURE
You can view a still picture on the TV screen during
playback (the Still mode). Press the PAUSE/STILL
button during playback. Only tapes recorded in the
Press the MENU button on the
SLP mode will show the least amount of lines.Press
remote control.
the PLAY button to return to playback.
Press the PLAY/K or STOP/L butNOTES:
ton to point to “ZERO RETURN”.
• Usually there will be video “noise” lines (black
Then, press the F.FWD/B button.
and white streaks or dots) on the screen. This is
The counter will appear on the TV
normal.
screen.
If the tape was originally recorded in SP or LP
The tape will automatically stop when the counter
mode, the still picture will be black and white in
addition to the “noise” lines.
TIME SERACH
This is not a fault of the machine, but is a byThe Time Search function makes it possible to
product of the technology involved in producing
quickly advance the tape to your desired position
a TV/VCR with 2 video heads.
simply by entering the exact amount of playback
If it is left in the Pause mode for more than five
•
time you want to skip.
minutes, the TV/VCR will automatically switch to
the Stop mode.
- 17 EN
4
To activate “ZERO RETURN” mode
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
B ZERO RETURN
TIME SEARCH
9J27
T4259.QX33
00.11.28 6:48 PM
Page 18
NOISE CANCEL (in the Still mode)
RENTAL PLAYBACK
This feature allows you to reposition or reduce the
noise lines of a still picture.Press the PAUSE/STILL
button so that the noise lines change position on the
screen so you can see the picture in its entirety without distracting noise lines.
NOTE: This feature can be activated ONLY when
viewing a tape recorded in the SLP mode. If the tape
was originally recorded in the SP or LP mode, the
still picture may revert to black and white in addition
to the “noise bars”. This is normal.
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1
2
Set “RENTAL” to [ON]
– USER’S SET UP –
Press the PLAY/K or STOP/L button to point to “RENTAL”.
Press the F.FWD/B or REW/s
button until [ON] appears.
3
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
B RENTAL
REPEAT PLAY
AUTO RETURN
[ON]
[OFF]
[OFF]
Exit the Rental setting
Press the MENU button on the remote control to
return to the TV mode.
PICTURE CONTROLS
TRACKING ADJUSTMENT
4
• Tracking adjustment will be set automatically
•
–MENU–
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
VERTICAL HOLD CONTROL
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL K or L button.
NOTE:
If there are video noise lines on the screen, reposition
or reduce them. Refer to “NOISE CANCEL”.
Select “USER’S SET UP”
(Digital Tracking function) when you start playback.
However when playing pre-recorded tapes or tapes
recorded on units other than your own, noise lines
(black and white streaks) may appear on the playback picture. If this occurs, you can adjust the
tracking control manually by pressing the CHANNEL K or L button until the streaks disappear. To
return to the DTR function, stop the tape once and
start playback again.
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
• Once you select the Rental mode, it stays in effect
even after you turn off the TV/VCR.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
RECORDING
TWO DIFFERENT TAPE SPEEDS
ERASE PREVENTION
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each
mode.
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tape Speed
Type of tape
Recording/Playback Time
T60
T120
T160
SP mode
1 hour
2 hours
2-2/3 hours
SLP mode
3 hours
6 hours
8 hours
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Note: You can play back a tape recorded in LP mode
(Long Play).
- 18 -
Transparent Tape
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 19
Make sure ...
• TV/VCR power must be turned on.
• Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTE: This unit will ONLY record and view the same channel.
NORMAL RECORDING
OTR (One Touch Recording)
You can ONLY watch the same TV program that is
being recorded.
1
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/VCR.
Select the channel to be recorded
Press the number buttons on the
CH 10
remote control or the CHANNEL
K or L button.
Remember: If the TV/VCR is connected to a cable box or satellite
box, the TV/VCR must be on CH3
or CH4, then the channel to be recorded must be
selected on the cable box or satellite box.
2
Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
SP
3
Begin recording
REC
Press the RECORD button.
SP
4
Stop recording
Press the STOP button when recording is completed.
SKIPPING UNWANTED
SCENES DURING RECORDING
1
Press the PAUSE/STILL button to
temporarily stop recording.
Press the PAUSE/STILL or
RECORD button to resume recording.
NOTES:
• After five minutes, the TV/VCR will automatically
switch to the Recording mode to prevent tape damage.
PAUSE
SP
Make sure ...
• TV/VCR power must be turned on.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTES:
• This function CANNOT be done from the remote
control.
• Recording starts immediately when the REC/OTR
button is pressed.
• When the REC/OTR button is pressed 18 times, the
TV/VCR returns to the Normal Recording mode.
• To stop the OTR operation, press the STOP button
on the TV/VCR or on the remote control.
• To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momentarily then disappear.)
• Recording stops when 0:00 is reached.
• Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120).
• If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediately, ejects the tape and turns itself off.
Select the channel to be recorded
Press the number buttons on the remote control or the
CHANNEL K or L button.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be recorded is selected on
the cable box or satellite box.
2
Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
- 19 -
EN
9J27
T4259.QX33
3
00.11.28 6:48 PM
Begin OTR
Page 20
Avoid over lap of programs ...
There is a chance that a program will not be recorded. when programs overlap;
• The program with an earlier start has priority.
• Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
OTR(2 : 30)
Press the REC/OTR button on the
TV/VCR as many times as needed.
The recording length will be determined by the number of times you
press the REC/OTR button. Each
additional push will increase the recording time by
30 minutes. It is set up to 8 hours.
SP
Push(es)
1 push
2 pushes
3 pushes
Display
17 pushes
8:00
0:30
1:00
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
Recording length
(normal recording)
30 minutes
60 minutes
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
• The illustration below demonstrates the sequence
480 minutes
of recordings.
TIMER RECORDING
1
You may set the TV/VCR to start and end a recording while you are away. You can set 8 programs to
record on specific days, daily or weekly within a 1
year period.
In the example below, the timer is being set to record:
DATE:
July 6th, 2001
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
CH61
TAPE SPEED:
SP
Make sure ...
• If a cable box or satellite box is connected with the
TV/VCR you will be limited to record only one
channel. And the channel selector on the TV/VCR
must be selected to the output channel of the boxes
CH 3 or CH 4 and then the actual channel to be
recorded must be selected on the boxes.
• Clock must be set to the correct time and date
before setting the timer.
• TV/VCR power must be turn on to program it.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
• The channel you want to record is properly set in
advance.
Select “TIMER PROGRAMMING”
Press the MENU button on the
remote control.
Confirm “TIMER PROGRAMMING” is pointed by pressing the
PLAY/K button.
And press the F.FWD/B button.
• If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow stops [3] to [8] on page 15.
Then set the timer recording.
–MENU–
B TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
– TIMER PROGRAMMING –
CH DATE
2
Select your desired program
B -
-
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
-
-
-
-
position (1~8)
Press the PLAY/K or STOP/L button to select the desired program
position.
Then, press the F.FWD/B button.
3
– TIMER PROGRAMMING –
CH DATE
---B 61
-----
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Set the channel number
Press the PLAY/K or STOP/L button until the
desired channel number appears.
(Example: CH61)
Then, press the F.FWD/B button.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR
must be on CH3 or CH4, then the
channel to be recorded is selected
on the cable box or satellite box.
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 7/06 FRI -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
4
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Select once, every day or
– TIMER PROGRAMMING –
weekly recording
For once recording :
Press the PLAY/K (up) button
- 20 -
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY DAY -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 21
until the desired date appears. (Example: “7/06”
for July 6th). Then, press the F.FWD/B button.
For every day recording : To record a TV program at
the same time on the same channel every day.
(Example: Monday through
Sunday)
– TIMER PROGRAMMING –
CH DATE
Press the STOP/L (down) button
until “EVRY DAY” appears.
Then, press the F.FWD/B button.
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
11
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
Press the STOP/L (down) button until “EVRY”
and your desired day of the week appear together.
Then, press the F.FWD/B button.
5
Set beginning hour
Press the PLAY/K or STOP/L button until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the F.FWD/B button.
6
Set beginning minute
Press the PLAY/K or STOP/L button until the desired minute
appears. (Example: “30” for
7:30PM)
Then, press the F.FWD/B button.
7
Set end hour
Press the PLAY/K or STOP/L button until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the F.FWD/B button.
8
Set end minute
Press the PLAY/K or STOP/L button until the desired minute
appears. (Example: “50” for
8:50PM)
Then, press the F.FWD/B button.
9
Set the tape speed
Press the PLAY/K or STOP/L button until the desired tape speed
appears. (Example: SP)
10
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/06 FRI 7:12 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
-
-
-
-
- - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - P
P
B 61 7/06 FRI 7:30 M 8:30 M - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - -
-
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/06 FRI
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:-:-:-:-:-:-:-:-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
BEGIN END
- - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - P
P
B 61 7/06 FRI 7:30 M 8:50 M- - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - - - -/- - - - - -:- -:- - -
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
2)Repeat step [1] on page 21.
3)Press the RECORD button and select the desired
program using the PLAY/K or STOP/L button.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the
PAUSE/STILL button on the remote control. The
recording time returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automatically be set to the SLP mode.
5)Press the F.FWD/B or REW/s button to exit the
setting menu. Then press the MENU button on the
remote control to return to original mode.
-
• While setting a program; press the REW/s but•
– TIMER PROGRAMMING –
CH DATE
Set the timer
Press the POWER button to set automatic timer
recording. The TIMER REC indicator lights up.
• You must turn off the TV/VCR to activate automatic timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
TO CORRECT A PROGRAM
– TIMER PROGRAMMING –
CH DATE
Finish setting the program
Press the F.FWD/B or REW/s button. The program
is now completed.
• To set another program, repeat steps [2] to [10].
• Press the MENU button on the remote control to
return to original mode.
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
M
8:50
M SP
61
7/06
FRI
7:30
B
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
- 21 -
ton to go back one step and enter the correct numbers using the PLAY/K or STOP/L button.
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 21.
3)Press the F.FWD/B button (or press the REW/s
button to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the PLAY/K or STOP/L button.
4)Press the POWER button to set automatic timer
recording.
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 22
TO CANCEL AN AUTOMATIC TIMER
RECORDING
2
• After setting a program;
•
1)Press the POWER button.
2)Repeat steps [1] ~ [2] on page 21 and select a
program you want to cancel.
3)Press the T-PROG. CLEAR button.
4)Press the MENU button on the remote control to
return to TV mode.
While recording is in progress;
1)Press POWER button.
2)Press the STOP/EJECT button on the TV/VCR.
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the REC indicator
goes off.
2)Press the MENU button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the F.FWD/B button. The details of programs appear on the TV screen.
5)Press the MENU button on the remote control to
return to TV mode.
HINTS FOR AUTOMATIC
TIMER RECORDING
Press the PLAY/K or STOP/L button to point to “AUTO RETURN”.
Press the F.FWD/B or REW/s
button until [ON] appears.
3
•
•
•
•
•
•
AUTO RETURN
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
1
Select “USER’S SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
B AUTO RETURN
[OFF]
[OFF]
[ON]
Auto Return will begin
When all the timer recordings are completed, the
TV/VCR will rewind to the beginning of the recorded
program(s).
NOTE:
• If you press the POWER button while tape is
rewinding, the Auto Return will stop.
4
Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
WAKE UP TIMER
• Make sure the channel you want to record is prop-
erly set in advance.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
If you are recording using a Timer mode, you may
not operate the unit manually.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediately, and the tape will be ejected.
Set “AUTO RETURN” to [ON]
The Wake Up Timer function turns on the TV/VCR
without using the POWER button after a desired
period of time.
NOTES:
• Use the remote control for this procedure.
• Clock must be set to the correct time before setting
the timer.
• If you want to select [TAPE], you must insert a
cassette tape in the TV/VCR. The tape will start
playback automatically on your desired time.
1
Select “WAKE UP TIMER”
Press the WAKE UP/SLEEP button
on the remote control once, and
confirm “ON/OFF” is pointed.
Press the F.FWD/B or REW/s
button until [ON] appears.
2
[ON]
[TV]
[12:00AM]
WAKE UP
ON/OFF
TIMER
B TV/TAPE
TIME
[ON]
[TV]
[12:00AM]
Select “TV” or “TAPE”
Press the PLAY/K or STOP/L button until to point to “TV/TAPE”.
Press the F.FWD/B or REW/s
button, and select [TV] or [TAPE].
- 22 -
WAKE UP B ON/OFF
TIMER
TV/TAPE
TIME
EN
9J27
T4259.QX33
3
00.11.28 6:48 PM
Page 23
1
Set wake up time
Press the PLAY/K or STOP/L button until to point to “TIME”.
Press the F.FWD/B or REW/s
button until your desired wake up
time appears.
Each additional push will increase (or decrease) the
time by 10 minutes.
WAKE UP
TIMER
ON/OFF
TV/TAPE
B TIME
Select “SLEEP TIMER”
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
[ON]
[TV]
[12:00AM]
2
Set sleep time
Press the MENU button on the remote control to
return to TV mode.
Press the PLAY/K, STOP/L,
F.FWD/B or REW/s button until
your desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120 minutes.
Press the MENU button on the remote control to exit
the Sleep Timer setting.
TO CANCEL THE WAKE UP TIMER
TO CANCEL THE SLEEP TIMER
Repeat step [1] but select [OFF].
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
To view the time left for sleep timer press the WAKE
UP/SLEEP button twice, then press the MENU button on the remote control to exit the sleep timer setting.
SLEEP TIMER
4
Exit the Wake Up Timer setting
SLEEP TIMER
The Sleep Timer function turns off the TV/VCR
without using the POWER button after a desired
period of time.
NOTE:
• This function does not operate during Recording
mode.
[2:00]
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends
or relatives for your enjoyment.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your TV/VCR and a Source (Playing) VCR
using the following diagram.
POWER
AUDIO
[Fig.8]
VIDEO
REC
[The TV/VCR]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
adapter cable
(not supplied)
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record over, into the TV/VCR’s cassette compartment.
3)Press the SPEED button on remote control for the
TV/VCR to select the desired recording speed
(SP/SLP).
4)Press the CHANNEL K or L button on the
TV/VCR until “AUX” appears on the screen.
NOTE: “AUX” is found below the lowest memorized channel. (Example: CH2)
5)Press the RECORD button on the TV/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during dubbing, use the
TV/VCR’s front panel controls whenever possible.
The remote control might affect the source (Playing)
VCR’s playback operation.
VIDEO
OUT
IN
AUDIO
- 23 -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 24
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
• Counter mode: After 5 seconds, only
•
<Off mode>
<Counter mode>
the counter remains. To clear it, press
the DISPLAY button.
Clock mode: After 5 seconds, only
the clock and the channel number
remain. To clear them, press the DISPLAY button.
<Clock mode>
5:40PM
CH2
Press
once
Press
once
COUNT 0:12:34
Press once
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time
will not change on a blank tape or blank portions on
the tape.)The “–” indication will appear when the
tape has rewound further than “0:00:00” on the tape
counter.
• When the end of a tape is reached during record-
•
•
ing, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding
finishes, the TV/VCR will eject the tape and turn
itself to off.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer recording or One Touch Recording.
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
•
the TV/VCR with a soft cloth immersed in lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/VCR. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or
•
1.Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-256-2487, to
locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
SERVICING
remove a cassette, so you can see a clear picture.
Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your TV/VCR may need
to be cleaned.
• Should your TV/VCR become inoperative, do not
- 24 -
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800256-2487, to locate an Authorized Service Center.
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 25
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to
remedy the problem.
PROBLEM
No picture but the audio is OK in
playback.
CORRECTIVE ACTION
Make
sure
the
AC
cord
is connected to an AC outlet.
•
• Make sure the car battery cord is connected to vehicle’s cigarette
lighter socket and to DC 13.2V jack on back of the TV/VCR.
• Check the fuse (5A, 250V) in car battery cord.
• Make sure the power is turned on.
• Make sure the AC cord is connected to an AC outlet.
• Check antenna connection.
• Let the TV/VCR program its’ tuner memory.
• Adjust direction or replace antenna.
• Adjust picture controls.
• Adjust volume control on remote control or main unit.
• Press the MUTE button to restore sound.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the TV/VCR clock is set correctly.
• Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
• Adjust tracking control for a better picture using the CHANNEL K
• or L button on the TV/VCR.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 27.
No operation by infrared Remote
Control.
Video or color fades in and out
when making a copy of a video tape.
Can not set the auto clock to ON.
“DEW” appears on the screen.
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
• Make sure the AC cord is connected to an AC outlet.
• Refer to page 4 “WARNING”.
No power.
No picture and sound.
No picture or poor picture on
TV/VCR.
No sound or poor sound.
Timer recording is not possible.
Cannot go into Record mode.
Playback picture is partially noisy.
- 25 -
EN
9J27
T4259.QX33
00.11.28 6:48 PM
Page 26
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
CRT :
9 inch in-line gun, 90˚
deflection tube
NTSC-M
Rotary two-head
1/2 inch
Video input level :
Audio input level :
Video S/N ratio :
Audio S/N ratio :
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
OTHER SPECIFICATIONS
Television system :
Video Heads :
Tape width :
Tape speed
SP :
LP :
SLP :
Tuner channel
TV VHF Low :
TV VHF High :
TV UHF :
CATV
VHF :
MID band :
SUPER band :
HYPER band :
Terminals
Antenna input :
Power requirement :
Power consumption :
Dimensions :
#2~#6
#7~#13
#14~#69
Weight :
5A
A5~A1, A~I
J~W
W+1~W+84
AC 120V/60Hz
DC 13.2V
AC/DC 60W
H:13” (330mm)
W:12-1/8” (308mm)
D:12-15/16” (329mm)
18.7 lbs (8.5kg)
• Designs and specifications are subject to change
•
VHF/UHF 75 ohms
unbalanced
RCA connector [ 1
RCA connector [ 1
1/8” monaural (3.5 mm)
Video input :
Audio input :
Earphone :
0.5~2.0Vp-p
-15dBs
More than 46dB
More than 43dB
without notice and without our legal obligation.
If there is a discrepancy between languages, the
default language will be English.
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
5A
2
3
4
5
6
7
8
9
10
11
12
13
A
B
TV Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CATV channel
TV Display
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
CATV channel
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
TV Display
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CATV channel W+10
TV Display
46
CATV channel W+25
W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
47
48
49
50
51
52
53
54
55
56
57
58
59
60
W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
TV Display
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
CATV channel W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
76
CATV channel W+55
TV Display
91
CATV channel W+65
TV Display
106
CATV channel W+80
TV Display
121
77
78
79
W+56 W+57 W+58
92
93
94
80
81
82
83
84
85
86
A-5
A-4
A-3
A-2
A-1
W+59 W+60 W+61 W+62 W+63 W+64
95
96
97
98
99
100
101
87
102
88
103
89
104
90
105
W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
107
108
109
110
111
112
113
114
115
116
117
118
119
120
W+81 W+82 W+83 W+84
122
123
124
125
- 26 -
EN
9J27
T4259BCV.QX33
00.11.28 6:49 PM
Page 32
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from
the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded
from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or
if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT
FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest FUNAI Authorized Service Center or for general service procedure,
please call 1-800-256-2487 or write to the following:
FUNAI CORPORATION
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-256-2487
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0EMN
T4259UK * * * * *
Download PDF

advertising