Embedded Computing for
Business-Critical ContinuityTM
ATCA-7150 and RTM-ATCA-7150
Getting Started
Document: 6806800G42B
December 2008
©
2008 Emerson
All rights reserved.
Trademarks
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service
marks of Emerson Electric Co. © 2008 Emerson Electric Co. All other product or service names are the property of their respective
owners.
Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Java™ and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other
countries.
Microsoft®, Windows® and Windows Me® are registered trademarks of Microsoft Corporation; and Windows XP™ is a trademark of
Microsoft Corporation.
PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the PCI
Industrial Computer Manufacturers Group.
UNIX® is a registered trademark of The Open Group in the United States and other countries.
Notice
While reasonable efforts have been made to assure the accuracy of this document, Emerson assumes no liability resulting from any
omissions in this document, or from the use of the information obtained therein. Emerson reserves the right to revise this document
and to make changes from time to time in the content hereof without obligation of Emerson to notify any person of such revision or
changes.
Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to
a Emerson website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise
altered without the permission of Emerson,
It is possible that this publication may contain reference to or information about Emerson products (machines and programs),
programming, or services that are not available in your country. Such references or information must not be construed to mean that
Emerson intends to announce such Emerson products, programming, or services in your country.
Limited and Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply
unless otherwise agreed to in writing by Emerson.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in
Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and
Documentation clause at DFARS 252.227-7014 (Jun. 1995).
Contact Address
Emerson Network Power - Embedded Computing
Lilienthalstr. 15
85579 Neubiberg/Munich
Germany
Contents
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.1
1.2
1.3
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.3.1 Supported Board Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.3.2 Board Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installation of the RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.1
2.2
2.3
2.4
2.5
2.6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Unpacking and Inspecting RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Environmental and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.3.1 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.3.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Module Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1 Ejector Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.4.2 ESD Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installation Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.5.1 Wearing the ESD-Preventive Wrist Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.5.2 Removing Filler Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installing and Replacing Daughter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2.6.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2.6.2 Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.6.3 GE Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
2.6.3.1 Installation Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.6.3.2 Installing the GE Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
2.6.3.3 Replacing the GE Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
2.6.4 FC Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.6.4.1 Installation Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
3
Contents
Contents
2.7
2.8
3
Hardware Installation of ATCA-7150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3.1
3.2
3.3
3.4
3.5
3.6
3.7
4
2.6.4.2 Installing the FC Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.6.4.3 Replacing the FC Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Installing and Removing the RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
2.7.1 Installing RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
2.7.2 Removing RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Connecting External Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.8.1 Connecting KVM Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.8.2 Connecting Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
2.8.3 Connecting Optical Fibers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Unpacking and Inspecting the Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Environmental and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3.3.1 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3.3.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
3.4.1 ESD Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Checking the Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.5.1 Wearing the ESD-Preventive Wrist Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.5.2 Removing Blank Filler Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Installing Blade Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
3.6.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
3.6.2 Optional Components Supported by the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
3.6.3 Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
3.6.4 DIMM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3.6.4.1 Installing the DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
3.6.4.2 Replacing the DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3.6.5 Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
3.6.5.1 Installing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
3.6.5.2 Replacing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Installing and Removing the Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
3.7.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
3.7.1.1 Installing the ATCA-7150 in a Powered Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
3.7.1.2 Checking the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Contents
3.7.1.3
Removal
3.7.2.1
3.7.2.2
Ejector Handles
3.7.2
3.8
A
Power-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Removing the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
A.1
A.2
A.3
A.4
A.5
A.6
A.7
A.8
A.9
A.10
A.11
A.12
A.13
A.14
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Contacting Emerson Network Power for Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
LED Display Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
A.6.1 LEDs Are Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
A.6.2 In Service (IS) LED Blinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Power-On Startup Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Component Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
A.8.1 Component Is Unavailable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
A.8.2 Number of DIMMs Is Inconsistent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Power Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
A.9.1 ATCA-7150 Cannot Be Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
A.9.2 ATCA-7150 Automatically Shuts Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Peripheral Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
A.10.1 Keyboard Cannot Be Used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
A.10.2 Mouse Cannot Be Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
A.10.3 Monitor Remains Dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
A.10.4 Monitor Display Is Abnormal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
A.10.5 No Information Is Displayed on the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Other Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
A.11.1 USB Interface Cannot Be Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
A.11.2 Network Connection Is Faulty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
A.11.3 A Fault Occurs in Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Uncertain Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
POST Code Checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
DIM Code Checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
5
Contents
Contents
A.15 ACPI Code Checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
B
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
B.1
B.2
6
Emerson Network Power - Embedded Computing Documents . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
List of Tables
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 2-1
Table 2-2
Table 3-1
Table 3-2
Table 3-3
Table 3-4
Table 3-5
Table 3-6
Table 3-7
Table 3-8
Table A-1
Table A-2
Table A-3
Table B-1
Table B-2
Functions of the ATCA-7150 and the RTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Available Board Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Environmental Requirements RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Power Requirements RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
List of Packing Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Environment for Installing the ATCA-7150 Suite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Optional Components Supported by the ATCA-7150 Suite . . . . . . . . . . . . . . . . . . . . . . . 80
DIMM Configuration on the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Insertion and Removal of the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Power-On and Power-Off of the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
POST code checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
DIM code checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
ACPI code checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Emerson Network Power - Embedded Computing Publications . . . . . . . . . . . . . . . . . . 119
Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
7
List of Tables
8
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
List of Figures
Figure 1-1
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 2-5
Figure 2-6
Figure 2-7
Figure 2-8
Figure 2-9
Figure 2-10
Figure 2-11
Figure 2-12
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
Figure 3-8
Figure 3-9
Connection Between the ATCA-7150 and the RTM . . . . . . . . . . . . . . . . . . . . . . . . . .
Wearing the ESD-Preventive Wrist Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Filler Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Structure of RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the GE Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the GE Daughter Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the FC Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the FC Daughter Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the KVM Cables to RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Network Cables to RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Optical Fibers to RTM-ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . .
Wearing the ESD-Preventive Wrist Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Blank filler blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positions of the DIMM Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the ATCA-7150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
30
41
43
47
50
52
56
58
61
63
65
66
67
76
78
82
84
86
88
90
92
96
9
List of Figures
10
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
About this Manual
Overview of Contents
This document describes the ATCA-7150 and RTM-ATCA-7150 server suite (hereinafter
referred to as the ATCA-7150 and RTM-ATCA-7150 suite) in the following aspects:
z
Functions, features, and appearance of the ATCA-7150 and RTM-ATCA-7150
z
How to install, deploy, and maintain the ATCA-7150 and RTM-ATCA-7150
The user must be a professional engineer in the server device field, who has been trained and is
able to identify danger levels when operating the device.
The body part focuses on the operation process, while the appendix part contains a lot of
supporting information. This helps you to get the required information quickly and accurately.
This manual is divided into the following chapters and appendices.
z
Safety Notes on page 17 lists safety notes applicable to the blade.
z
Sicherheitshinweise on page 23 is the German translation of the previous English safety
notes (this had to be included for legal reasons).
z
Chapter 1, Introduction, on page 29 describes the main features of the ATCA-7150 and
RTM-ATCA-7150.
z
Chapter 2, Installation of the RTM-ATCA-7150, on page 35 describes the installation of the
RTM.
z
Chapter 3, Hardware Installation of ATCA-7150, on page 69 describes installation
prerequisites including the blade installation itself of the front blade.
z
Troubleshooting on page 99 provides troubleshooting information.
z
Related Documentation on page 119 provides links to further ATCA-7150 and RTM-ATCA7150-related documentation.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
11
About this Manual
About this Manual
Abbreviations
This document uses the following abbreviations:
12
Abbreviation
Definition
ACA
Australian Communications Authority
BIOS
Basic Input/Output System
BMC
Baseboard Management Controller
CMOS
Complementary Metal Oxide Semiconductor
CPU
Central Processing Unit
DC
Direct Current
DIMM
Dual Inline Memory Module
ECC
Error Checking and Correcting
EIA
Electronics Industries Association
EMC
Electromagnetic Compatibility
ESD
Electro-Static Discharge
FBD
Fully Buffer DIMM
FC
Fiber Channel
FCC
Federal Communications Commission
FRU
Field Replaceable Unit
GE
Gigabit Ethernet
IEC
International Electrotechnical Commission
IPMB
Intelligent Platform Management BUS
IPMI
Intelligent Platform Management Interface
KVM
Keyboard, Video, and Mouse
OOS
Out of Service
PCI
Peripheral Component Interconnect
PEM
Power Entry Module
POST
Power-On Self Test
RAID
Redundant Arrays of Independent Disks
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
About this Manual
Abbreviation
Definition
RTM
Rear Transition Module
SAS
Serial Attached Small Computer System Interface
SCSI
Small Computer System Interface
SDR
Sensor Data Record
SEL
System Event Log
ShMC
Shelf Management Controller
SOL
Serial Over LAN
UL
Underwriters Laboratories Inc
USB
Universal Serial Bus
Conventions
The following table describes the conventions used throughout this manual.
Notation
Description
0x00000000
Typical notation for hexadecimal numbers (digits are
0 through F), for example used for addresses and
offsets
0b0000
Same for binary numbers (digits are 0 and 1)
bold
Used to emphasize a word
Screen
Used for on-screen output and code related elements
or commands in body text
Courier + Bold
Used to characterize user input and to separate it
from system output
Reference
Used for references and for table and figure
descriptions
File > Exit
Notation for selecting a submenu
<text>
Notation for variables and keys
[text]
Notation for software buttons to click on the screen
and parameter description
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
13
About this Manual
About this Manual
Notation
Description
...
Repeated item for example node 1, node 2, ..., node
12
.
Omission of information from example/command
that is not necessary at the time being
.
.
..
Ranges, for example: 0..4 means one of the integers
0,1,2,3, and 4 (used in registers)
|
Logical OR
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury
Indicates a hazardous situation which, if not avoided,
may result in minor or moderate injury
Indicates a property damage message
No danger encountered. Pay attention to important
information
Summary of Changes
This manual has been revised and replaces all prior editions.
14
Part Number
Publication Date
Description
6806800G42A
June 2008
First edition
6806800G42B
December 2008
Updated to Emerson layout, editorial changes
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
About this Manual
Comments and Suggestions
We welcome and appreciate your comments on our documentation. We want to know what
you think about our manuals and how we can make them better.
Mail comments to us by filling out the following online form:
http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form
In "Area of Interest" select "Technical Documentation". Be sure to include the title, part number,
and revision of the manual and tell us how you used it.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
15
About this Manual
About this Manual
16
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Safety Notes
This section provides warnings that precede potentially dangerous procedures throughout
this manual. Instructions contained in the warnings must be followed during all phases of
operation, service, and repair of this equipment. You should also employ all other safety
precautions necessary for the operation of the equipment in your operating environment.
Failure to comply with these precautions or with specific warnings elsewhere in this manual
could result in personal injury or damage to the equipment.
Emerson Network Power intends to provide all necessary information to install and handle the
product in this manual. Because of the complexity of this product and its various uses, we do
not guarantee that the given information is complete. If you need additional information, ask
your Emerson Network Power representative.
The product has been designed to meet the standard industrial safety requirements. It must
not be used except in its specific area of office telecommunication industry and industrial
control.
Only personnel trained by Emerson Network Power or persons qualified in electronics or
electrical engineering are authorized to install, remove or maintain the product.
The information given in this manual is meant to complete the knowledge of a specialist and
must not be used as replacement for qualified personnel.
Keep away from live circuits inside the equipment. Operating personnel must not remove
equipment covers. Only Factory Authorized Service Personnel or other qualified service
personnel may remove equipment covers for internal subassembly or component replacement
or any internal adjustment.
Do not install substitute parts or perform any unauthorized modification of the equipment or
the warranty may be voided. Contact your local Emerson Network Power representative for
service and repair to make sure that all safety features are maintained.
EMC
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
17
Safety Notes
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense. Changes or
modifications not expressly approved by Emerson Network Power Embedded Computing
could void the user's authority to operate the equipment. Board products are tested in a
representative system to show compliance with the above mentioned requirements. A proper
installation in a compliant system will maintain the required performance. Use only shielded
cables when connecting peripherals to assure that appropriate radio frequency emissions
compliance is maintained.
Operation
Damage of the Product
Surface of the Product
High humidity and condensation on the product surface causes short circuits.
Do not operate the product outside the specified environmental limits. Make sure the product
is completely dry and there is no moisture on any surface before applying power.
Do not operate the product below -5°C.
Overheating and Damage of the Product
Operating the product without forced air cooling may lead to overheating and thus damage of
the product.
When operating the product, make sure that forced air cooling is available in the shelf.
Configuration Jumpers
Malfunction of the Product
Reserved jumpers might carry production-related functions and can cause the product to
malfunction if their setting is changed.
Therefore, do not change settings of jumpers marked as "Reserved".
18
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Safety Notes
Installation
Damage of the Product and Additional Devices and Modules
Incorrect installation or removal of additional devices or modules may damage the product or
the additional devices or modules.
Before installing or removing additional devices or modules, read the respective
documentation.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.
Before touching the product or electronic components, make sure that your are working in an
ESD-safe environment.
Damage of the Product
Incorrect installation of the product can cause damage of the product.
Only use handles when installing/removing the product to avoid damage/deformation to the
face plate and/or PCB.
Damage to the Product/Backplane or System Components
Bent pins or loose components can cause damage to the product, the backplane, or other
system components.
Therefore, carefully inspect the product and the backplane for both pin and component
integrity before installation.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
19
Safety Notes
Emerson Network Power Embedded Computing (ENPEC) and our suppliers take significant
steps to ensure there are no bent pins on the backplane or connector damage to the boards
prior to leaving the factory. Bent pins caused by improper installation or by inserting boards
with damaged connectors could void the ECC warranty for the backplane or boards.
Incorrect installation of the product can cause blade damage.
Only use handles for when installing/removing the product to avoid damage/deformation to
the face plate and/or PCB
Cabling and Connectors
Damage of the Product
The RJ-45 connector(s) on the face plate are either twisted-pair Ethernet (TPE) or E1/T1/J1
interfaces. Connecting an E1/T1/J1 line to an Ethernet connector may damage the product.
z
Make sure that TPE connectors near your working area are clearly marked as network
connectors.
z
Verify that the length of an electric cable connected to a TPE bushing does not exceed 100
meters.
Make sure the TPE bushing of the product is connected only to safety extra low voltage
circuits (SELV circuits).
If in doubt, ask your system administrator.
z
Laser
This product is a Class 1 laser product. The use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous radiation exposure.
Environment
Always dispose of used blades, system components and RTMs according to your country’s
legislation and manufacturer’s instructions.
20
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Safety Notes
Battery
Board/System damage
Incorrect exchange of lithium batteries can result in a hazardous explosion.
When exchanging the on-board lithium battery, make sure that the new and the old battery
are exactly the same battery models.
If the respective battery model is not available, contact your local Emerson Network Power
sales representative for the availablity of alternative officially approved battery models.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
21
Safety Notes
22
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Sicherheitshinweise
Dieses Kapitel enthält Hinweise, die potentiell gefährlichen Prozeduren innerhalb dieses
Handbuchs vorrangestellt sind. Beachten Sie unbedingt in allen Phasen des Betriebs, der
Wartung und der Reparatur des Systems die Anweisungen, die diesen Hinweisen enthalten
sind. Sie sollten außerdem alle anderen Vorsichtsmaßnahmen treffen, die für den Betrieb des
Produktes innerhalb Ihrer Betriebsumgebung notwendig sind. Wenn Sie diese
Vorsichtsmaßnahmen oder Sicherheitshinweise, die an anderer Stelle diese Handbuchs
enthalten sind, nicht beachten, kann das Verletzungen oder Schäden am Produkt zur Folge
haben.
Emerson ist darauf bedacht, alle notwendigen Informationen zum Einbau und zum Umgang
mit dem Produkt in diesem Handbuch bereit zu stellen. Da es sich jedoch um ein komplexes
Produkt mit vielfältigen Einsatzmöglichkeiten handelt, können wir die Vollständigkeit der im
Handbuch enthaltenen Informationen nicht garantieren. Falls Sie weitere Informationen
benötigen sollten, wenden Sie sich bitte an die für Sie zuständige Geschäftsstelle von Emerson.
Das System erfüllt die für die Industrie geforderten Sicherheitsvorschriften und darf
ausschließlich für Anwendungen in der Telekommunikationsindustrie und im Zusammenhang
mit Industriesteuerungen verwendet werden.
Einbau, Wartung und Betrieb dürfen nur von durch Emerson ausgebildetem oder im Bereich
Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden. Die in diesem
Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen von
Fachpersonal zu ergänzen, können dieses jedoch nicht ersetzen.
Halten Sie sich von stromführenden Leitungen innerhalb des Produktes fern. Entfernen Sie auf
keinen Fall Abdeckungen am Produkt. Nur werksseitig zugelassenes Wartungspersonal oder
anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen, um Komponenten
zu ersetzen oder andere Anpassungen vorzunehmen.
Installieren Sie keine Ersatzteile oder führen Sie keine unerlaubten Veränderungen am Produkt
durch, sonst verfällt die Garantie. Wenden Sie sich für Wartung oder Reparatur bitte an die für
Sie zuständige Geschäftsstelle von Emerson. So stellen Sie sicher, dass alle
sicherheitsrelevanten Aspekte beachtet werden.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
23
Sicherheitshinweise
EMV
Das Produkt wurde in einem Emerson Network Power Standardsystem getestet. Es erfüllt die
für digitale Geräte der Klasse A gültigen Grenzwerte in einem solchen System gemäß den FCCRichtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese Grenzwerte sollen einen
angemessenen Schutz vor Störstrahlung beim Betrieb des Produktes in Gewerbe- sowie
Industriegebieten gewährleisten.
Das Produkt arbeitet im Hochfrequenzbereich und erzeugt Störstrahlung. Bei
unsachgemäßem Einbau und anderem als in diesem Handbuch beschriebenen Betrieb können
Störungen im Hochfrequenzbereich auftreten.
Wird das Produkt in einem Wohngebiet betrieben, so kann dies mit grosser Wahrscheinlichkeit
zu starken Störungen führen, welche dann auf Kosten des Produktanwenders beseitigt werden
müssen. Änderungen oder Modifikationen am Produkt, welche ohne ausdrückliche
Genehmigung von Emerson Network Power EC durchgeführt werden, können dazu führen,
dass der Anwender die Genehmigung zum Betrieb des Produktes verliert. Boardprodukte
werden in einem repräsentativen System getestet, um zu zeigen, dass das Board den oben
aufgeführten EMV-Richtlinien entspricht. Eine ordnungsgemässe Installation in einem System,
welches die EMV-Richtlinien erfüllt, stellt sicher, dass das Produkt gemäss den EMV-Richtlinien
betrieben wird. Verwenden Sie nur abgeschirmte Kabel zum Anschluss von Zusatzmodulen. So
ist sichergestellt, dass sich die Aussendung von Hochfrequenzstrahlung im Rahmen der
erlaubten Grenzwerte bewegt.
Warnung! Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt werden,
angemessene Maßnahmen durchzuführen.
Betrieb
Beschädigung des Produktes
Hohe Luftfeuchtigkeit und Kondensat auf der Oberfläche des Produktes können zu
Kurzschlüssen führen.
Betreiben Sie das Produkt nur innerhalb der angegebenen Grenzwerte für die relative
Luftfeuchtigkeit und Temperatur. Stellen Sie vor dem Einschalten des Stroms sicher, dass sich
auf dem Produkt kein Kondensat befindet und betreiben Sie das Produkt nicht unter -5°C.
24
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Sicherheitshinweise
Überhitzung und Beschädigung des Produktes
Betreiben Sie das Produkt ohne Zwangsbelüftung, kann das Produkt überhitzt und schließlich
beschädigt werden.
Bevor Sie das Produkt betreiben, müssen Sie sicher stellen, dass das Shelf über eine
Zwangskühlung verfügt.
Jumper
Fehlfunktion des Produktes
Schalter, die mit 'Reserved' sind, können mit produktionsrelevanten Funktionen belegt sein.
Das Ändern dieser Schalter kann im normalen Betrieb Störungen auslösen.
Installation
Beschädigung des Produktes und von Zusatzmodulen
Fehlerhafte Installation von Zusatzmodulen, kann zur Beschädigung des Produktes und der
Zusatzmodule führen.
Lesen Sie daher vor der Installation von Zusatzmodulen die zugehörige Dokumentation.
Beschädigung von Schaltkreisen
Elektrostatische Entladung und unsachgemäßer Ein- und Ausbau des Produktes kann
Schaltkreise beschädigen oder ihre Lebensdauer verkürzen.
Bevor Sie das Produkt oder elektronische Komponenten berühren, vergewissern Sie sich, daß
Sie in einem ESD-geschützten Bereich arbeiten.
Beschädigung des Produktes
Fehlerhafte Installation des Produktes kann zu einer Beschädigung des Produktes führen.
Verwenden Sie die Handles, um das Produkt zu installieren/deinstallieren. Auf diese Weise
vermeiden Sie, dass das Face Plate oder die Platine deformiert oder zerstört wird.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
25
Sicherheitshinweise
Beschädigung des Produktes, der Backplane oder von System Komponenten
Verbogene Pins oder lose Komponenten können zu einer Beschädigung des Produktes, der
Backplane oder von Systemkomponenten führen.
Überprüfen Sie daher das Produkt sowie die Backplane vor der Installation sorgältig und stellen
Sie sicher, dass sich beide in einwandfreien Zustand befinden und keine Pins verbogen sind.
Emerson Network Power Embedded Computing (ENPEC) und unsere Zulieferer unternehmen
größte Anstrengungen um sicherzustellen, dass sich Pins und Stecker von Boards vor dem
Verlassung der Produktionsstätte in einwandfreiem Zustand befinden. Verbogene Pins,
verursacht durch fehlerhafte Installation oder durch Installation von Boards mit beschädigten
Steckern kann die durch ECC gewährte Garantie für Boards und Backplanes erlöschen lassen.
Kabel und Stecker
Beschädigung des Produktes
Bei den RJ-45-Steckern, die sich an dem Produkt befinden, handelt es sich entweder um
Twisted-Pair-Ethernet (TPE) oder um E1/T1/J1-Stecker. Beachten Sie, dass ein versehentliches
Anschließen einer E1/T1/J1-Leitung an einen TPE-Stecker das Produkt zerstören kann.
z
Kennzeichnen Sie deshalb TPE-Anschlüsse in der Nähe Ihres Arbeitsplatzes deutlich als
Netzwerkanschlüsse.
z
Stellen Sie sicher, dass die Länge eines mit Ihrem Produkt verbundenen TPE-Kabels 100 m
nicht überschreitet.
Das Produkt darf über die TPE-Stecker nur mit einem Sicherheits-KleinspannungsStromkreis (SELV) verbunden werden.
Bei Fragen wenden Sie sich an Ihren Systemverwalter.
z
Laser
Einige Varianten des Produktes sind Laserprodukte der Klasse 1. Um nicht schädlicher
Laserstrahlung ausgesetzt zu werden, beachten Sie die folgenden Hinweise: Anpassungen am
Produkt, die Bedienung von Steuerelementen sowie die Durchführung von Prozeduren dürfen
nur gemäß den Anweisungen in diesem Dokument erfolgen.
26
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Sicherheitshinweise
Umweltschutz
Entsorgen Sie alte Batterien und Blades/RTMs stets gemäß der in Ihrem Land gültigen
Gesetzgebung und den Empfehlungen des Herstellers.
Batterie
Beschädigung des Produktes
Ein unsachgemäßer Einbau der Batterie kann gefährliche Explosionen und Beschädigungen
des Produktes zur Folge haben.
Verwenden Sie deshalb nur den Batterietyp, der auch bereits eingesetzt wurde und befolgen
Sie die Installationsanleitung.
Falls der entsprechende Batterietyp nicht verfügbar ist, kontaktieren Sie Ihren lokalen Emerson
Network Power-Ansprechpartner und erfragen Sie die Verfügbarkeit von alternativen, offiziell
zugelassenen Batteriemodellen.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
27
Sicherheitshinweise
28
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Introduction
1.1
Chapter: 1
Features
The ATCA-7150 and RTM-ATCA-7150 server blade suite features the capabilities of high speed
calculation and mass data processing.
The ATCA-7150 and RTM-ATCA-7150 suite consists of:
z
ATCA-7150 and RTM-ATCA-7150
z
RTM-ATCA-7150
The RTM-ATCA-7150 is the rear transition module (RTM) of the server blade.
A server blade must work with an RTM of the server blade. For example, the ATCA-7150 works
with the RTM-ATCA-7150.
You can install the ATCA-7150 in any node slot of your shelf. The RTM-ATCA-7150 is installed
in the slot that is paired with the ATCA-7150 slot.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
29
Introduction
Figure 1-1 shows the connection between the ATCA-7150 and the RTM of the server blade.
Figure 1-1
Connection Between the ATCA-7150 and the RTM
RTM of the
server blade
ATCA7150
Backplane
You can choose to use the RTM-ATCA-7150 according to the actual application.
The backplane is one part of the shelf. For details on the backplane and shelf, refer to the
respective system documentation.
30
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Introduction
Table 1-1 lists the functions of the ATCA-7150 and the RTM.
Table 1-1 Functions of the ATCA-7150 and the RTM
Function
Description
Processing functions
z
Supports two dual-core LV Intel Xeon 5138 (2.13 GHz)
processors
z
Supports 4 MB L2 cache
z
Supports up to four FB-DIMMs
z
Supports the DIMM with a capacity of 512 MB, 1 GB, 2 GB, or 4
GB. The maximum capacity is 16 GB
z
10/100/1000Base-T
z
1000Base-BX
z
1000Base-BX
z
Provides two USB 2.0 interfaces (compatible with USB 1.1)
z
Provides one IPMC serial port (also used as the system serial
port, the serial port standards are RS232 and RJ-45)
z
Provides serial port to access CPU and IPMC serial console
z
Provides two SAS hard disks
z
The RTM-ATCA-7150 that works with the ATCA-7150 provides a
monitor interface and a USB 2.0 interface (compatible with
USB1.1). Through optional daughter cards, the RTM-ATCA-7150
can also provide external GE interfaces, and FC interfaces.
Interface functions
Management functions
The ATCA-7150 provides the IPMC that is powered independently.
The IPMC is connected to the ShMC through the redundant IPMB.
The IPMC provides the following functions:
Integrity functions
z
Environmental sensors temperature, voltage
z
System Event Logs
z
Watchdog timer
z
Power-on, power-off, cold reset
z
SOL(Serial Over LAN)
z
FRU Hot-swap management
z
E-Keying control
z
Dual-channel GE controller
z
IPMI
z
SAS storage controller
z
Video controller
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
31
Introduction
1.2
Standard Compliances
This product meets the following standards.
Table 1-2 Standard Compliances
Standard
Description
UL 60950-1
Legal safety requirements
EN 60950-1
IEC 60950-1
CAN/CSA C22.2 No 60950-1
CISPR 22
CISPR 24
EMC requirements (legal) on system level (predefined Emerson
Network Power system)
EN 55022
EN 55024
FCC Part 15
Industry Canada ICES-003
VCCI Japan
AS/NZS CISPR 22
EN 300 386
NEBS Standard GR-1089 CORE
NEBS Standard GR-63-CORE
Environmental requirements
ETSI EN 300019 series
PICMG 3.0
1.3
Defines mechanics, blade dimensions, power distribution,
power and data connectors, and system management
Ordering Information
When ordering board variants or board accessories, use the order numbers given on the
following pages.
32
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Introduction
1.3.1
Supported Board Models
The following table explains the product nomenclature used for the available board variants.
Table 1-3 Product Nomenclature
Order Number
Description
ATCA-7150-0GB
ATCA Processor Blade with Dual Core Intel® Xeon® Processor
LV5138.
Can be equipped with up to 16GB DDR2 memory.
1G fabric interface.
1.3.2
ATCA-7X50-MEM-2G
2G Memory Module (min 1, max 4 modules of the same type per
blade)
ATCA-7X50-MEM-4G
4G Memory Module (min 1, max 4 modules of the same type per
blade)
RTM-ATCA-7150-GE
Rear Transition Module for ATCA-7150, 2x 1G Ethernet
RTM-ATCA-7150-GE-FC
Rear Transition Module for ATCA-7150, 2x 1G Eth, 2x FC
ATCA7X50-HDD1-SAS
Enterprise Class HDD, SAS, 72GB
ATCA7X50-HDD2-SAS
Enterprise Class HDD, SAS, 146GB
ATCA7X50-HDD3-SATA
Automotive HDD, SATA, 80GB
ATCA-7150-8GB-1HDD1
ATCA Processor Blade with Dual Core Intel® Xeon® Processor
LV5138, 8GB (4x 2GB) Memory, 1x Enterprise Class HDD, SAS,
72GB
ATCA7X50-SSD2-SATA
Solid State Disk, SATA, 32GB
Board Accessories
As of the printing date of this manual, the following board accessories were available.
Table 1-4 Available Board Accessories
Board Accesories
Order Number
Gigabit Ethernet (GE) daughter card
MEZC-RTM-7150-GE
Fiber Channel (FC) daughter card
MEZC-RTM-7150-FC
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
33
Introduction
Table 1-4 Available Board Accessories (continued)
Board Accesories
ATCA7X50-HDDx-SAS/SATA
Order Number
ATCA7X50-HDD1-SAS
ATCA7X50-HDD2-SAS
ATCA7X50-HDD3-SATA
ATCA7X50
34
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
2.1
Chapter: 2
Overview
This chapter describes:
2.2
z
Unpacking and inspecting RTM-ATCA-7150
z
Precautions during the operation
z
Preparations before installation
z
Installation procedure
z
Installing and replacing daughter cards
z
Connection of external cables
z
Removal procedure
Unpacking and Inspecting RTM-ATCA-7150
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.
Before touching the product or electronic components, make sure that your are working in
an ESD-safe environment.
Shipment Inspection
To inspect the shipment, perform the following steps.
1. Verify that you have received all items of your shipment:
Printed "Getting Started" guide
RTM-ATCA-7150
Any optional items ordered
2. Check for damage and report any damage or differences to the customer service.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
35
Installation of the RTM-ATCA-7150
3. Remove the desiccant bag shipped together with the blade and dispose of it
according to your country’s legislation.
The product is thoroughly inspected before shipment. If any damage occurred during
transportation or any items are missing, please contact our customer's service immediately.
2.3
Environmental and Power Requirements
The following environmental and power requirements are applicable to the board.
2.3.1
Environmental Requirements
Table 2-1 Environmental Requirements RTM-ATCA-7150
36
Requirement
Operating
Non-Operating
Temperature
+5ºC (41ºF) to +40ºC (104ºF) (normal operation)
according to NEBS Standard GR-63-CORE
-5ºC to +55ºC (short term operation) according
to NEBS Standard GR-63-CORE
-40ºC (-40ºF) to +70ºC
(158ºF) (may be further
limited by installed
accessories)
Temp. Change
+/- 0.25ºC/min or 15ºC/h (59ºF/h) according to
NEBS Standard GR-63-CORE
+/- 0.25ºC/min or 15ºC/h
(59ºF/h)
Rel. Humidity
5% to 85% non-condensing according to
Emerson Network Power Embedded
Computing-internal environmental
requirements
5% to 85% non-condensing
according to Emerson
Network Power Embedded
Computing-internal
environmental
requirements
Altitude
<= 4000m
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
Table 2-1 Environmental Requirements RTM-ATCA-7150 (continued)
Requirement
Operating
Non-Operating
Vibration
1.0g from 5 to 100 Hz and back to 5 Hz at a rate
of 0.1 octave/minute
5-20 Hz @ 0.01 g2/Hz
20-200 Hz @ -3.0 dB/octave
Random 5-20 Hz @ 1
m2/Sec3
Random 20-200 Hz @ -3
m/Sec2
Shock
Half-sine, 11 m/Sec, 30mSec/sec2
Blade level packaging
Half-sine, 6 mSec at 180
m/Sec2
Free Fall
1,200 mm/all edges and
corners
1.0m (Packaged) per ETSI
300 019-2-2 (Blade level
packaging)
100mm (unpackaged) per
GR-63-CORE
2.3.2
Power Requirements
Table 2-2 Power Requirements RTM-ATCA-7150
Requirement
Operating
Power supply
Provided by the server blade
Maximum power consumption
14.2 W
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
37
Installation of the RTM-ATCA-7150
2.4
Module Installation and Removal
Personal Damage through Electric Shock
There is current in the power cords and communication cables. Touching the connectors of
the power cords and communication cables may cause electric shock.
Do not touch the connectors of power cords and communication cables
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.
Before touching the product or electronic components, make sure that your are working in
an ESD-safe environment.
Module Damage
If the blade is not fully aligned with the interface in the backplane, too much force may twist
the pins on the blade or backplane.
Do not exert too much force when you insert the blade.
Note the following points at the time of installing RTM-ATCA-7150:
38
z
Make sure that you wear an electrostatic discharge (ESD)-preventive wrist strap to prevent
the static electricity from hurting you or damaging the device.
z
Keep your personal objects such as your clothes away from RTM-ATCA-7150. To prevent
the static electricity on clothing, you need to put on antistatic clothing.
z
RTM-ATCA-7150 is installed in the slot paired with the server blade slot at the back side of
the shelf. You should install RTM-ATCA-7150 before the server blade is installed.
Otherwise, RTM-ATCA-7150 cannot be powered on normally.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
2.4.1
z
Hold the ejector handles and the face plate when you insert or remove RTM-ATCA-7150.
Do not touch the components inside of the blades.
z
Keep the blade vertical when you install RTM-ATCA-7150. Align the blade with the slot and
then insert it in the shelf.
Ejector Handles
RTM-ATCA-7150 is powered by the server blade in the slot paired with the RTM-ATCA-7150
slot. RTM-ATCA-7150 does not support hot swap. The face plate of ATCA-7150 and RTM-ATCA7150 provides an upper and a lower ejector handles. The ejector handles help to insert,
remove, fasten, power on, and power off RTM-ATCA-7150.
2.4.2
ESD Prevention
Static electricity may hurt you or damage the device. To minimize the damage, pay attention
to the following points:
z
Before you operate the device, wear the ESD-preventive wrist strap. Both terminals of the
ESD-preventive wrist strap must contact well. One terminal touches your bare skin, and
the other is inserted in the jack at the front or back side of the shelf. For details on how to
wear the ESD-preventive wrist strap, refer Wearing the ESD-Preventive Wrist Strap.
z
Avoid moving your body as much as possible. Movement gathers static electricity around
you.
z
Do not touch the solder point, pin, or bare circuit.
z
Do not leave the device in the place where others can operate it.
z
Install the device at once after you take it out of the antistatic package. If you need to lay
down the device, place it back in the antistatic package. Do not lay the device on the shelf
or cabinet.
z
Monitor the temperature and humidity of the equipment room. Warm air decreases the
humidity and increases the static electricity in the room.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
39
Installation of the RTM-ATCA-7150
2.5
Installation Preparations
The installation preparations process includes:
2.5.1
z
check the installation environment
z
wear the ESD-preventive wrist strap
z
remove the blank filler panels
z
unpack and check the RTM-ATCA-7150 suite
Wearing the ESD-Preventive Wrist Strap
Module Damage
40
z
Electrostatic discharge can damage circuits or shorten their life.
z
The ESD-preventive wrist strap prevents only the static electricity on your body from
damaging the blade. To prevent the static electricity on your clothes, it is recommended
to wear the antistatic clothes. Additionally, you have to make sure that the cabinet and
shelf are properly grounded - for details, refer to the corresponding system
documentation.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
To wear the ESD-preventive wrist strap, proceed as follows:
1. Wrap the ESD-preventive wrist strap around your wrist, as shown in the figure
below.
2. Fasten the latch. Make sure that the ESD-preventive wrist strap well touches your
bare wrist.
3. Insert the grounding terminal of the ESD-preventive wrist strap in the jack of the
cabinet or shelf.
There is a jack for inserting the ESD-preventive wrist strap respectively in the lower right
corners at both front and back sides of the shelf.
Figure 2-1
Wearing the ESD-Preventive Wrist Strap
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
41
Installation of the RTM-ATCA-7150
2.5.2
Removing Filler Blades
After a filler blade is removed, place it in the equipment room or other moisture-proof and
dust-proof places.
You should install a blank filler blade in the slot after removing the blade. Otherwise, it may
effect the ventilation, heat dissipation, electromagnetic shielding and dust prevention of the
shelf.
If this is the first installation for the shelf, the blade is fully configured and the shelf is not
powered on, you can remove all the filler blades. Then, install blades in the slots in order. This
document takes the first installation as an example.
If you want to install multiple blades in the shelf that is powered on shelf, you can remove a
filler blade and then install a blade one by one.
If the slot is occupied with a filler blade you have to remove it first.
42
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
To remove the filler blade, proceed as follows:
1. As shown in step 1 of the figure below, use a screwdriver to anticlockwise loosen
the two captive screws on a filler blade.
2. As shown in step 2 of the figure below, remove the filler blade.
Figure 2-2
Removing the Filler Blade
1
2
1
2.6
Installing and Replacing Daughter Cards
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
43
Installation of the RTM-ATCA-7150
2.6.1
Precautions
Incorrect installation or removal of additional devices or modules may damage the product
or the additional devices or modules.
Before installing or removing additional devices or modules, read the respective
documentation.
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.
Before touching the product or electronic components, make sure that your are working in
an ESD-safe environment.
Do not exert too much force when you insert the blade.
If the blade is not fully aligned with the interface in the backplane, too much force may twist
the pins on the blade or backplane.
Do not touch the connectors of power cords and communication cables.
There is current in the power cords and communication cables. Touch on the connectors of
the power cords and communication cables may cause electric shock.
Note the following points at the time of installing or replacing components:
44
z
Make sure that you wear an electrostatic discharge (ESD)-preventive wrist strap to prevent
the static electricity from hurting you or damaging the device.
z
Keep the area where the components reside clean and keep the components away from
the heat-generating devices, such as radiators.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
2.6.2
z
Ensure that your sleeves are tightened or rolled up above the elbow. For safety purpose, it
is not recommended to wear jewelry, watch, glasses with metal frame, or clothes with
metal buttons.
z
Do not exert too much force, or insert or remove the components forcibly. Avoid damage
to the components or plug-ins, for example, the pins are bent or get short circuit.
Preparations
Before you install or replace a component, make the following preparations
z
Confirming the feasibility of the operation
—
There are available spare parts of the component to be installed or replaced in the
equipment warehouse. When the available spare parts are in short supply, contact
Emerson Network Power Embedded Computing for help in time.
—
Make sure that the new component is in good condition, without defects such as
oxidation, chemical corrosion, missing component, or transportation damage.
—
By reading this document, you are familiar with how to install and replace the
component and master the skills required by the operation.
z
Checking the environment
Make sure that the shelf, power supply, temperature, and humidity meet the operating
requirements of the blades and components. For details, refer to ATCA-7150 Installation
and Use Manual and other related documents.
z
Preparing spare parts and tools
z
—
Prepare the component to be installed or replaced.
When you hold or transport the component, use the special antistatic package. In
addition, you need to tidy, record, and repair the component during routine
maintenance.
—
Prepare the cross screwdriver, screws, plastic supports, cooling gel, and ESDpreventive wrist strap.
The supplier provides a list of tools and negotiates with you to decide the tool provider.
Confirming installation or changing positions
Confirm the positions of the cabinet, the shelf, and the slot where RTM-ATCA-7150 is
installed. Then, stick a label on the face plate of RTM-ATCA-7150 to avoid wrong operation.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
45
Installation of the RTM-ATCA-7150
z
2.6.3
Others
If a serious problem occurs and cannot be solved when you install or replace the
component, contact Emerson Network Power Embedded Computing for technical
support.
GE Daughter Card
This manual considers the GE daughter card providing two external Ethernet interfaces as an
example, and describes how to install the daughter card on and remove it from RTM-ATCA7150.
46
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
2.6.3.1
Installation Positions
When the GE daughter card is used with the RTM-ATCA-7150 it can be installed on the
daughter card connector J1, J2, J3, J4. The default position as used on the RTM-ATCA-7150-GE
is position J4. The default position as used on the RTM-ATCA-7150-GE-FC is position J1.
Figure 2-3
Structure of RTM-ATCA-7150
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
47
Installation of the RTM-ATCA-7150
2.6.3.2
Installing the GE Daughter Card
To install the GE daughter card, proceed as follows.
1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap.
2. Lay RTM-ATCA-7150 where the GE daughter card is to be installed on the antistatic
desktop.
3. As shown in step 1 of the figure below, insert two plastic supports vertically in the
holes used to fasten the GE daughter card.
4. As shown in step 2 of the figure below, at the back side of RTM-ATCA-7150, use a
screwdriver to clockwise fasten the two screws used to fix the plastic supports.
5. Take the GE daughter card out of the antistatic package.
48
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
6. Insert the GE daughter card in RTM-ATCA-7150 by facing the daughter card at an
angle of 45° to the RTM. Align the daughter card connector with the connector on
RTM-ATCA-7150, and the daughter card positioning holes with the plastic supports
on RTM-ATCA-7150. Exert even power downwards until the daughter card
connector is fully inserted into the connector on RTM-ATCA-7150 and the daughter
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
49
Installation of the RTM-ATCA-7150
card is fastened by the plastic latches. See step 3 in the figure below.
Figure 2-4
Installing the GE Daughter Card
1
2
3
50
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
7. Insert RTM-ATCA-7150 with the GE daughter card installed in the shelf. For more
information refer, Installing RTM-ATCA-7150.
After installation, check if RTM-ATCA-7150 can be powered on and work normally. Use the
network cable to connect RTM-ATCA-7150 to the external network. Check if the network is
connected properly and monitor whether the network port indicator is normal.
2.6.3.3
Replacing the GE Daughter Card
To replace the GE daughter card, proceed as follows.
1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap.
2. Remove the RTM-ATCA-7150 whose GE daughter card is to be replaced. For more
information refer, Removing RTM-ATCA-7150.
3. As shown in step 1 of the figure below, open the plastic latches fastening the GE
daughter card.
4. Exert even force upwards until the daughter card connector is removed from the
connector on RTM-ATCA-7150. As shown in step 2 of the figure below, remove the
daughter card by facing the daughter card at an angle of 45° to the RTM.
5. Place the removed GE daughter card in an antistatic package.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
51
Installation of the RTM-ATCA-7150
6. Take the new GE daughter card out of the antistatic package.
Figure 2-5
Replacing the GE Daughter Card.
2
1
3
52
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
7. Insert the GE daughter card in RTM-ATCA-7150 by facing the daughter card at an
angle of 45° to the RTM. Align the daughter card connector with the connector on
RTM-ATCA-7150, and the daughter card positioning holes with the plastic supports
on RTM-ATCA-7150. Exert even power downwards until the daughter card
connector is fully inserted into the connector on RTM-ATCA-7150 and the daughter
card is fastened by the plastic latches. See step 3 in the figure above.
8. Install RTM-ATCA-7150 whose GE daughter card is replaced. For more information
refer, Installing RTM-ATCA-7150.
After replacement, check if RTM-ATCA-7150 can be powered on and work normally. Use the
network cable to connect RTM-ATCA-7150 to the external network. Check if the network is
connected properly and monitor whether the network port indicator is normal.
2.6.4
FC Daughter Card
This manual considers the FC daughter card providing two external FC interfaces as an
example, and describes how to install the daughter card on and remove it from RTM-ATCA7150.
2.6.4.1
Installation Positions
When the FC daughter card is used with the RTM-ATCA-7150 it can be installed on the
daughter card connector J2, J4. The default position as used on the RTM-ATCA-7150-GE-FC is
position J4 and J1.
2.6.4.2
Installing the FC Daughter Card
To install the FC daughter card, proceed as follows.
1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap.
2. Lay RTM-ATCA-7150 where the FC daughter card is to be installed on the antistatic
desktop.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
53
Installation of the RTM-ATCA-7150
3. As shown in step 1 of the figure below, insert two plastic supports vertically in the
holes used to fasten the FC daughter card.
4. As shown in step 2 of the figure below, at the back side of RTM-ATCA-7150, use a
screwdriver to clockwise fasten the two screws used to fix the plastic supports.
5. Take the FC daughter card out of the antistatic package.
54
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
6. Insert the GE daughter card in RTM-ATCA-7150 by facing the daughter card at an
angle of 45° to the RTM. Align the daughter card connector with the connector on
RTM-ATCA-7150, and the daughter card positioning holes with the plastic supports
on RTM-ATCA-7150. Exert even power downwards until the daughter card
connector is fully inserted into the connector on RTM-ATCA-7150 and the daughter
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
55
Installation of the RTM-ATCA-7150
card is fastened by the plastic latches. See step 3 in the figure below.
Figure 2-6
Installing the FC Daughter Card
1
2
3
7. Insert RTM-ATCA-7150 with the FC daughter card installed in the shelf. For more
56
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
information refer, Installing RTM-ATCA-7150.
After installation, check if RTM-ATCA-7150 can be powered on and work normally. Use the
optical fiber to connect RTM-ATCA-7150 to the external storage system. Check if RTM-ATCA7150 can transmit data normally and monitor whether the FC status indicator is normal.
2.6.4.3
Replacing the FC Daughter Card
To replace the FC daughter card, proceed as follows.
1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap.
2. Remove the RTM-ATCA-7150 whose FC daughter card is to be replaced. For more
information refer, Removing RTM-ATCA-7150.
3. As shown in step 1 of the figure below, open the plastic latches fastening the FC
daughter card.
4. Exert even force upwards until the daughter card connector is removed from the
connector on RTM-ATCA-7150. As shown in step 2 of the figure below, remove the
daughter card by facing the daughter card at an angle of 45° to the RTM.
5. Place the removed FC daughter card in an antistatic package.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
57
Installation of the RTM-ATCA-7150
6. Take the new FC daughter card out of the antistatic package.
Figure 2-7
Replacing the FC Daughter Card.
1
2
3
58
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
7. Insert the FC daughter card in RTM-ATCA-7150 by facing the daughter card at an
angle of 45° to the RTM. Align the daughter card connector with the connector on
RTM-ATCA-7150, and the daughter card positioning holes with the plastic supports
on RTM-ATCA-7150. Exert even power downwards until the daughter card
connector is fully inserted into the connector on RTM-ATCA-7150 and the daughter
card is fastened by the plastic latches. See step 3 in the figure above.
8. Install RTM-ATCA-7150 whose FC daughter card is replaced. For more information
refer, Installing RTM-ATCA-7150.
After replacement, check if RTM-ATCA-7150 can be powered on and work normally. Use the
optical fibre to connect RTM-ATCA-7150 to the external storage system. Check if RTM-ATCA7150 can transmit data normally and monitor whether the FC status indicator is normal.
2.7
Installing and Removing the RTM-ATCA-7150
2.7.1
Installing RTM-ATCA-7150
Product Damage
You can install RTM-ATCA-7150 into a system if the front blade is already installed or if it is
not installed. In case the front blade is already installed, its payload has to be powered down
first.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
59
Installation of the RTM-ATCA-7150
Installation Procedure with Installed Front Blade
The following procedure describes the installation of RTM-ATCA-7150. It assumes that your
system is powered on. If your system is powered off, you can disregard the blue LED and thus
skip the respective step. In this case it is a purely mechanical installation. The same applies to
an installation without an installed front blade. In this case disregard the LEDs and skip the
respective step.
1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap.
2. Fully open the ejector handles of the front blade.
3. Take RTM-ATCA-7150 out of the antistatic package.
4. Fully open the upper and lower ejector handles of the RTM.
60
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
5. As shown in step 1 of the figure below, align the upper and lower sides of RTMATCA-7150 with the guide rails (the edges of the slot). Slide RTM-ATCA-7150 along
the guide rails until the positioning pins of RTM-ATCA-7150 are inserted in the
positioning holes in the shelf. The LEDs; OOS LED, Blue LED, and healthy LED are on.
Figure 2-8
Installing RTM-ATCA-7150
3
2
1
3
2
6. As shown in step 2 of the figure above, make sure that the ejector handles are
fastened to the beam. Close the upper and lower ejector handles inwards until the
inner sides of the ejector handles are attached to the face plate.
7. As shown in step 3 of the figure above, use the screwdriver to fasten the captive
screws clockwise to fix RTM-ATCA-7150. The LEDs of the RTM are off now.
8. Close the handles of the front blades
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
61
Installation of the RTM-ATCA-7150
2.7.2
Removing RTM-ATCA-7150
Product Damage
You should power off the front blade before removing RTM-ATCA-7150.
To remove RTM-ATCA-7150, proceed as follows:
1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap.
2. The OOS, blue, and the healthy LEDs of the RTM are on. Open the ejector handles
of the front blade to power it down.
3. As shown in step 2 of the figure below, use the screwdriver to unfasten the captive
screws of the RTM anticlockwise.
4. As shown in step 1 of the figure below, fully open the upper and lower ejector
handles.
62
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
5. As shown in step 3 of the figure below, remove RTM-ATCA-7150 along the guide
rails.
6. Place RTM-ATCA-7150 in the antistatic package.
Figure 2-9
Removing RTM-ATCA-7150
2
1
3
1
2
2.8
Connecting External Cables
After RTM-ATCA-7150 is installed in the shelf, you can connect the keyboard, video, and mouse
(KVM) cables.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
63
Installation of the RTM-ATCA-7150
If RTM-ATCA-7150 is configured with the GE daughter card and FC daughter card, it provides
the external GE network ports and external FC interfaces. Network cables and optical fibers can
be connected to RTM-ATCA-7150. You can choose to use one or more daughter cards
according to actual applications.
Cable Damage
2.8.1
z
There is a back cable trough at the back side of the shelf. You need to arrange and
identify all cables and then bind and fasten them in the back cable through after
connecting them.
z
If you use excessive force when installing cables, the cables may be damaged.
z
Do not exert too much force when you insert or remove the cables. Do not twist or tear
the cables in any condition.
Connecting KVM Cables
The figure below shows the method of connecting the Keyboard, Video, Mouse (KVM) cables
to RTM-ATCA-7150. Please refer to your local Emerson sales representative to obtain the cable.
Product Damage
You have to use matching interfaces for the KVM cables.
Use a PS/2-USB converter when connecting the KVM cables.
64
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
Figure 2-10
2.8.2
Connecting the KVM Cables to RTM-ATCA-7150
Connecting Network Cables
Electromagnetic Radiation
Make sure that the cable and connectors of the network cable are with shielding function
and that both ends of the shielded layer of the network cable are grounded. It is
recommended that the network cable is grounded through the metal cover of the network
port connector.
When RTM-ATCA-7150 is configured with the GE daughter card, it provides two external
Ethernet interfaces with 10/100/1000M Base-T auto-negotiation. Network cables are used to
connect RTM-ATCA-7150 to the external network. Please refer to your local Emerson sales
representative to obtain the cable.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
65
Installation of the RTM-ATCA-7150
The figure below shows the method of connecting the network cables to RTM-ATCA-7150.
Figure 2-11
2.8.3
Connecting the Network Cables to RTM-ATCA-7150
Connecting Optical Fibers
When RTM-ATCA-7150 is configured with the FC daughter card, it provides two external 2G FC
interfaces. Optical fibers are used to connect RTM-ATCA-7150 to the external Storage Area
Network (SAN) storage system. Please refer to your local Emerson sales representative to
obtain the cable.
66
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Installation of the RTM-ATCA-7150
As shown in steps 1 and 2 in the figure below, insert the optical module in the FC interface and
then insert the optical fibers in the optical module.
Figure 2-12
Connecting the Optical Fibers to RTM-ATCA-7150
1
2
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
67
Installation of the RTM-ATCA-7150
68
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.1
Chapter: 3
Overview
This chapter describes:
3.2
z
Unpacking and inspecting the blade
z
Environmental and power requirements
z
Precautions during the operation
z
Checking the installation environment
z
Installing accessories
z
Installation and removal procedures
z
Ejector handles
Unpacking and Inspecting the Blade
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the blade can damage
circuits or shorten their life.
Before touching the blade or electronic components, make sure that you are working in an
ESD-safe environment.
Shipment Inspection
To inspect the shipment, perform the following steps.
1. Verify that you have received all items of your shipment:
Printed "Getting Started" guide
ATCA-7150 blade
Any optional items ordered
2. Check for damage and report any damage or differences to the customer service.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
69
Hardware Installation of ATCA-7150
3. Remove the desiccant bag shipped together with the blade and dispose of it
according to your country’s legislation.
The blade is thoroughly inspected before shipment. If any damage occurred during
transportation or any items are missing, please contact our customer's service immediately.
Unpacking the Blade
To unpack and check the ATCA-7150 suite, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For more details, see Wearing the ESD-Preventive Wrist Strap on page 75.
2. Lay the packing carton according to the arrow direction on the cover.
3. Cut the tape to open the packing carton.
4. According to Table 3-1, check that the components are complete and in good condition,
without defects such as oxidation, chemical corrosion, missing component, or
transportation damage.
Table 3-1 List of Packing Items
70
SN
Description
1
Packing materials, such as packing carton, plastic package, and foam
2
Documentation bag, containing documents shipped with the product
3
ATCa-7150, which can be used with an RTM-ATCA-7150
4
RTM-ATCA-7150, which must be used with an ATCA-7150
5
Desiccant bag
z
The actual items in the packing carton are decided by the contract.
z
If you do not order an RTM of the server blade, all functions provided by the RTM are not
available.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.3
Environmental and Power Requirements
The following environmental and power rewuirements are applicable to the blade.
3.3.1
Environmental Requirements
Table 3-2 Environmental Requirements
Requirement
Operating
Non-Operating
Temperature
+5ºC (41ºF) to +40ºC (105ºF) (normal
operation) according to NEBS Standard GR63-CORE
The SAS drives can meet this
max temperature range of
non-operating.
-5ºC to +55ºC (exceptional operation)
according to NEBS Standard GR-63-CORE
-40ºC (-40ºF) to +70ºC
(158ºF).
Temp. Change
+/- 0.25ºC/min according to NEBS Standard
GR-63-CORE
+/- 0.25ºC/min
Rel. Humidity
5% to 85% non-condensing according to
Emerson Network Power-internal
environmental requirements
5% to 95% non-condensing
according to Emerson
Network Power-internal
environmental
requirements
Altitude
<=3000 m
Maximum weight
4.0 kg
Length x width x
height
322.3 mm × 280 mm × 29 mm
Vibration
0.1g from 5 to 100 Hz and back to 5 Hz at a
rate of 0.1 octave/minute
5-20 Hz at 0.01 g2/Hz
20-200 Hz at -3.0 dB/octave
Random 5-20 Hz at 1
m2/Sec3
Random 20-200 Hz at -3
m/Sec2
Shock
Half-sine, 11 m/Sec, 30mSec/sec2
Blade level packaging
Half-sine, 6 mSec at 180
m/Sec2
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
71
Hardware Installation of ATCA-7150
Table 3-2 Environmental Requirements (continued)
Requirement
Operating
Non-Operating
Free Fall
1,200 mm (Packaged) /all
edges and corners
1.0m (Packaged) per ETSI
300 019-2-2 (Blade level
packaging)
25 mm (unpackaged) per
GR-63-CORE
3.3.2
Power Requirements
Make sure that the blade is used in an AdvancedTCA shelf connected to -48VDC up to -60VDC,
according to Telecommunication Network Voltage (TNV-2). A TNV-2 circuit is a circuit whose
normal operating voltages exceed the limits for a safety-extra-low-voltage (SELV) under
normal operating conditions, and which is not subject to overvoltages from
telecommunication networks.
Table 3-3 lists the power requirements for the ATCA-7150.
Table 3-3 Power Requirements
Requirement
Operating
Rated Voltage
-48VDC to -60VDC
US and Canada: -48VDC
Operating Voltage
-39.0VDC to -72VDC
US and Canada: -39.0 to -60VDC
Input Current
3.75A at 48V
Power Dissipation
180W (max) 140W (min)
The blade provides two independent power inputs according to the AdvancedTCA
specification.
72
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.4
Precautions
Electric Shock
There is current in the power cords and communication cables. Touching the connectors of
the power cords and communication cables may cause electric shock.
Do not touch the connectors of power cords and communication cables.
Electrostatic Discharge
Do not touch the circuit board with bare hands.
The static electricity of the human body may damage the electrostatic sensitive devices
(ESSDs) on the circuit board.
Make sure that you wear an electrostatic discharge (ESD)-preventive wrist strap or antistatic
glove to prevent the static electricity from hurting you or damaging the device.
Keep your personal objects such as your clothes away from the ATCA-7150 suite. To prevent
the static electricity from damaging the device, it is recommended to wear antistatic clothes.
Pin Damage
If the blade is not fully aligned with the interface in the backplane, too much force may twist
the pins on the blade or backplane.
Do not exert too much force when you insert the blade.
Note the following points at the time of installing RTM-ATCA-7150:
z
If an RTM is planned to be used, you must install the RTM in the slot before installing the
ATCA-7150 in the paired slot. If the ATCA-7150 is installed first and shelf power is turned
on the RTM must not be installed in the paired slot.
z
To take the ATCA-7150 suite, hold the captive screw on the top of the face plate with one
hand and the lower edge of the blade with the other hand. Do not touch the components
of the blade.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
73
Hardware Installation of ATCA-7150
3.4.1
ESD Prevention
Static electricity may hurt you or damage the device. To minimize the damage, pay attention
to the following points:
z
Before you operate the device, wear the ESD-preventive wrist strap. Both terminals of the
ESD-preventive wrist strap must contact well. One terminal touches your bare skin, and
the other is inserted in the jack at the front or back side of the shelf. For details on how to
wear the ESD-preventive wrist strap, see Wearing the ESD-Preventive Wrist Strap on page 75.
z
Avoid moving as much as possible. Movement gathers static electricity around you.
z
Do not touch the solder point, pin, or bare circuit.
z
Do not leave the device in the place where others can operate it.
z
Install the device at once after you take it out of the antistatic package. If you need to lay
down the device, place it back in the antistatic package. Do not lay the device on the shelf
or cabinet.
z
Monitor the temperature and humidity of the equipment room. Warm air decreases the
humidity but increases the static electricity in the room.
Damage of Circuits
Electrostatic discharge and incorrect module installation and removal can damage circuits or
shorten their life. Before touching the module or electronic components, make sure that you
are working in an ESD-safe environment.
74
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.5
Checking the Installation Environment
Table 3-4 lists the environment for installing the ATCA-7150 suite.
Table 3-4 Environment for Installing the ATCA-7150 Suite
Item
Cabinet
Description
Cabinet that complies with the IEC297 standard
Note:
Leave enough space around the cabinet. Nothing blocks the fans and air
conditioner to ensure airflow and heat dissipation.
Shelf
Shelf of the system
Note:
Consider heat dissipation when you choose slots to install blades. If the shelf is
not fully configured, install the blades in scattered slots.
3.5.1
Wearing the ESD-Preventive Wrist Strap
Product Damage
Electrostatic discharge can damage circuits or shorten their life.
The ESD-preventive wrist strap prevents only the static electricity on your body from
damaging the blade. To prevent the static electricity on your clothes, it is recommended to
wear the antistatic clothes. Additionally, you have to make sure that the cabinet and shelf are
properly grounded - for details, refer to the respective system documentation.
The cable of an ESD-preventive wrist strap is limited. In this case, before you wear the ESDpreventive wrist strap, place the device within 0.5 m away from the shelf.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
75
Hardware Installation of ATCA-7150
To wear the ESD-preventive wrist strap, proceed as follows:
1. Wrap the ESD-preventive wrist strap around your wrist, as shown in Figure 3-1.
2. Fasten the latch. Make sure that the ESD-preventive wrist strap well touches your bare
wrist.
3. Insert the grounding terminal of the ESD-preventive wrist strap in the jack of the cabinet
or shelf.
Figure 3-1
76
Wearing the ESD-Preventive Wrist Strap
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.5.2
Removing Blank Filler Blades
z
After you remove a blank filler blade, store it in the equipment room or a damp-proof and
dust-proof place.
z
After you remove a blade from the shelf, install a blank filler blade in vacant slot.
Otherwise, the functions such as ventilation, heat dissipation, electromagnetic shield,
and dust proof may be affected.
z
For a newly-delivered shelf, you can remove all blank filler blades and then install blades
in all slots when the shelf is not powered on.
z
If a shelf is powered on, you can remove a blank filler blade and then install a blade. In this
way, install multiple blades one by one.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
77
Hardware Installation of ATCA-7150
Before you install the ATCA-7150 suite, remove blank filler blades from installation slots as
follows:
1. Use a screwdriver to anticlockwise loosen the two captive screws on a blank filler blade, as
shown in Figure 3-2.
2. Pull the blank filler blade out of the slot, as shown in Figure 3-2.
Figure 3-2
Removing the Blank filler blade
1
2
1
3.6
78
Installing Blade Accessories
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.6.1
Precautions
Electric Shock
There is current in the power cords and communication cables. Touching the connectors of
the power cords and communication cables may cause electric shock.
Do not touch the connectors of power cords and communication cables.
When you install or replace components, pay attention to the following points:
3.6.2
z
Wear the ESD-preventive wrist strap to prevent the static electricity from damaging the
device.
z
Keep the area where the components reside clean and keep the components away from
the heat generating devices, such as radiator.
z
Ensure that your sleeves are tightened or rolled up above the elbow. For safety purpose, it
is not recommended to wear jewelry, watch, glasses with metal frame, or clothes with
metal buttons.
z
Do not exert too much force, or insert or remove the components forcibly. Avoid damage
to the components or plug-ins.
Optional Components Supported by the ATCA-7150
Only those who are certificated or authorized by Emerson Network Power can replace or
change the components.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
79
Hardware Installation of ATCA-7150
Table 3-5 lists the optional components supported by the ATCA-7150.
Table 3-5 Optional Components Supported by the ATCA-7150 Suite
Blade
Supported Component
ATCA-7150 and
RTM-ATCA-7150
DIMM
Hard disk
Daughter cards on the RTM
For more information on the daughter cards, refer to RTM-ATCA-7150 Installation and Use
Manual, MESC-RTM-7150-FC Installation Information, and MESC-RTM-7150-GE Installation
Information.
3.6.3
Preparations
Before you install or replace the component, make the following preparations:
z
z
80
Confirming the feasibility of the operation
—
There are available spare parts of the component to be installed or replaced in the
equipment warehouse. When the available spare parts are lacking, contact Emerson
Network Power for help in time. For details on how to get help from Emerson Network
Power, see Contacting Emerson Network Power for Technical Support on page 100.
—
Make sure that the new component is in good condition, without defects such as
oxidation, chemical corrosion, missing component, or transportation damage.
—
By reading this document, you are familiar with how to install and replace the
component and master the skills required by the operation.
Checking the environment
Make sure that the shelf, power supply, temperature, and humidity meet the operating
requirement for the blades and components. For details, refer to the respective system
documentation.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
z
3.6.4
Preparing spare parts and tools
—
Prepare the component to be installed or replaced.
When you hold or transport the component, use the special antistatic package. Also,
you need to tidy, record, and repair the component during routine maintenance.
—
Prepare the cross screwdriver, screws, plastic supports, cooling gel, and ESDpreventive wrist strap.
The supplier provides a list of tools and negotiates with to decide the tool provider.
z
Confirming installation or changing position
Confirm the positions of the cabinet, the shelf, and the slot where the ATCA-7150 is
installed. Then, stick a label on the face plate of the ATCA-7150 to avoid wrong operation.
z
Others
If a serious problem occurs and cannot be solved when you install or replace the
component, contact Emerson Network Power for technical support. For details on contact
methods, see Contacting Emerson Network Power for Technical Support on page 100.
DIMM
When you install or replace the DIMM, pay attention to the following points:
z
The ATCA-7150 provides four DIMM interfaces and supports the DIMM with a capacity of
512 MB, 1 GB, 2 GB or 4 GB.
z
The DIMMs must have the same size, frequency, type, and technology, physical design and
manufacturer.
z
DIMMs must be of single or dual rank type. Quad rank types are not supported.
z
If the DIMMs are not fully configured, you need to install the required DIMMs in the related
interfaces.
—
If one DIMM is configured, install it in DIMM slot 0.
—
If two DIMMs are configured, install them in DIMM slots 0 and 1.
—
Configuring three DIMMs is not supported.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
81
Hardware Installation of ATCA-7150
Figure 3-3 shows the positions of the DIMM interfaces on the ATCA-7150.
Figure 3-3
Positions of the DIMM Interfaces
DIMM Slot1
DIMM Slot0
DIMM Slot3
DIMM Slot2
Table 3-6 DIMM Configuration on the ATCA-7150
Installation Positions
3.6.4.1
Number of DIMMs
CH0/J25
CH1/J39
1
x
2
x
x
4
x
x
CH2/J27
CH3/J28
x
x
Installing the DIMM
To install the DIMM, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
82
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
2. Lay the ATCA-7150 where the DIMM is to be installed on the antistatic desktop.
3. Take the DIMM out of the antistatic package.
4. Make sure that two interface fixing clips are fully open. Adjust the DIMM to align it with the
DIMM interface.
Product Damage
Operate the fixing clips slightly to avoid breaking them or damaging the DIMM interface.
5. Insert the DIMM in the interface along the guide rails, as shown in Figure 3-4.
If there is a gap between the DIMM and the fixing clips, the DIMM is not installed properly. In
this case, open the fixing clips and remove the DIMM. Then, insert the DIMM again.
6. Make sure that the fixing clips are fastened or closed firmly as shown in Figure 3-4.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
83
Hardware Installation of ATCA-7150
7. Insert the ATCA-7150 with the DIMM installed in the shelf.
For details, see Installing the ATCA-7150 in a Powered Shelf on page 91.
Figure 3-4
Installing the DIMM
2
2
1
You can install the DIMMs in other DIMM interfaces in the same way.
After installation, insert the ATCA-7150 in the shelf and power on the ATCA-7150. Check
whether the OS can be loaded properly. If it can be, in the OS, check whether the displayed
memory capacity is consistent with the actual one.
3.6.4.2
Replacing the DIMM
To replace the DIMM, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
2. Remove the ATCA-7150 whose DIMM is to be replaced.
84
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
For details, see Removing the ATCA-7150 on page 95.
Product Damage
z
To avoid breaking them or damaging the DIMM interface, do not exert too much power
to operate the fixing clips.
z
If you open the two fixing clips of the DIMM at the same time, the DIMM bounces from
the interface. Operate the fixing clips carefully to avoid damaging the DIMM.
3. Open one fixing clip of the DIMM carefully until the DIMM rises from the interface. Hold the
top edge of the DIMM and open the other fixing clip carefully until the DIMM is removed
from the interface, as shown in Figure 3-5.
4. Take the DIMM out of the interface carefully, as shown in Figure 3-5.
5. Place the faulty DIMM in the antistatic package.
6. Take the new DIMM out of the antistatic package.
7. Install the new DIMM.
For details, see Installing the DIMM on page 82.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
85
Hardware Installation of ATCA-7150
8. Install the ATCA-7150 with the DIMM replaced.
For details, see Installing the ATCA-7150 in a Powered Shelf on page 91.
Figure 3-5
Removing the DIMM
1
1
2
After replacement, check whether the OS can be loaded properly. If it can be, in the OS, check
whether the displayed memory capacity is consistent with the actual one.
3.6.5
Hard Disk
This section describes how to install and replace the hard disk on the ATCA-7150.
3.6.5.1
Installing the Hard Disk
For more information on the installation of the hard disk, refer to the HDD Installation Sheet.
To install the hard disk, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
2. Take the hard disk to be installed out of the antistatic package.
86
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3. Exert even force to push the hard disk smoothly in the hard disk holder. Align the screw
holes at the sides of the hard disk with those at the sides of the holder, as shown in Figure
3-6.
4. Use the screwdriver to fasten the four screws clockwise to fix the hard disk, as shown in
Figure 3-6.
5. Exert even force to push the hard disk in the fixing bracket on the ATCA-7150, as shown in
Figure 3-6.
6. Insert the ATCA-7150 with the hard disk installed in the shelf.
For details, see Installing the ATCA-7150 in a Powered Shelf on page 91.
You can install the other hard disk in the same way.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
87
Hardware Installation of ATCA-7150
After installation, check whether the ATCA-7150 can be powered on and work normally and
whether the data in the hard disk can be read and written normally.
Figure 3-6
Installing the Hard Disk
1
2
3
88
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.6.5.2
Replacing the Hard Disk
To replace the hard disk, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
2. Remove the ATCA-7150 whose hard disk is to be replaced.
For details, see Removing the ATCA-7150 on page 95.
3. Remove the finger on the hard disk holder in a direction as shown in Figure 3-7 to unlock
the hard disk.
4. Exert even force to pull the hard disk holder from the fixing bracket, as shown in Figure 3-7.
5. Unfasten the four screws used to fasten the hard disk anticlockwise, as shown in Figure 3-7.
6. Exert even force to pull the hard disk from the holder, as shown in Figure 3-7.
7. Place the faulty hard disk in the antistatic package.
8. Take the new hard disk out of the antistatic package.
9. Install the new hard disk.
For details, see Installing the Hard Disk on page 86.
10. Install the ATCA-7150 with the hard disk replaced.
For details, see Installing the ATCA-7150 in a Powered Shelf on page 91.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
89
Hardware Installation of ATCA-7150
After replacement, check whether the ATCA-7150 can be powered on and work normally and
whether the data in the hard disk can be read and written normally.
Figure 3-7
Removing the Hard Disk
2
1
4
3
90
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.7
Installing and Removing the Blade
3.7.1
Installation
RTM-ATCA-7150 must be installed before the ATCA-7150 to avoid product damage. For
information on how to install the RTM-ATCA-7150, refer to Chapter 2, Installation of the RTMATCA-7150, on page 35
3.7.1.1
Installing the ATCA-7150 in a Powered Shelf
The following procedure describes the installation of the blade. It assumes that your system is
powered and if applicable the RTM is installed. If your system is unpowered, you can disregard
the blue LED and thus skip the respective step. In this case it is a purely mechanical installation.
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75
2. Take the ATCA-7150 out of the antistatic package.
3. Fully open the upper and lower ejector handles.
4. Slide the ATCA-7150 along the guide rails until the positioning pins of the ATCA-7150 are
inserted in the positioning holes in the shelf, as shown in Figure 3-8.
5. Make sure that the upper and lower ejector handles are attached to the beam properly.
Close the upper and lower ejector handles until the inner sides of the ejector handles are
attached to the face plate, as shown in Figure 3-8. After closing the handles, the blue LED,
OOS and HEALTHY LEDs blink. When payload is powered on, the blue LED is continously
illuminated, and the OOS and HEALTHY LEDs are out.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
91
Hardware Installation of ATCA-7150
6. User the screwdriver to clockwise fasten the screws to fix the ATCA-7150, as shown in
Figure 3-8.
7. Fully open the ejector handles and the ATCA-7150 is ready for power-on. Before you power
on the ATCA-7150, connect the required external cables and check that the ATCA-7150 is
installed properly.
Figure 3-8
Installing the ATCA-7150
3
2
1
2
3
3.7.1.2
Checking the Installation
After you install the RTM of the server blade and the ATCA-7150, and connect and bind cables,
check whether:
92
z
The ATCA-7150 and RTM are installed in the paired slots.
z
The upper and lower ejector handles of the RTM are fully closed.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.7.1.3
z
The cables are properly connected.
z
The cables are well bound.
Power-On
The RTM of the server blade is powered by the ATCA-7150 in the slot paired with the RTM
slot. The RTM of the server blade does not support hot swap. Therefore, the RTM must be
installed in the slot before the ATCA-7150 is installed in the paired slot.
3.7.1.3.1 Checks Before Power-On
Before power-on, you need to confirm that:
z
The RTM of the server blade and SMM are installed properly.
z
The shelf and SMM are powered on properly.
z
The required external cables are connected.
z
The upper and lower ejector handles of the ATCA-7150 are opened.
3.7.1.3.2 Procedure
To power on the ATCA-7150, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
93
Hardware Installation of ATCA-7150
2. Close the upper and lower ejector handles.
The HOTSWAP LED blinks at the short blink rate. The OOS and HEALTHY LEDs blink for 10
times at the same time. When the OOS and HOTSWAP LEDs are off and the HEALTHY LED
is on (green), the ATCA-7150 is powered on properly.
During power-on, if the HEALTHY LED blinks (red), an alarm occurs to the ATCA-7150.
3.7.2
3.7.2.1
Removal
z
Before you remove an ATCA-7150 or RTM of the server blade, prepare packing materials,
such as an antistatic package.
z
Before you remove an ATCA-7150 or RTM of the server blade, power off the ATCA-7150.
For details on how to power off the ATCA-7150, see Power Off on page 94.
Power Off
The RTM of the server blade is powered by the ATCA-7150 in the slot paired with the RTM
slot. The RTM of the server blade does not support hot swap. You can remove the RTM only
when the ATCA-7150 is powered off and removed from the slot.
94
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
3.7.2.1.1 Checks Before Power-Off
Before power-off, you need to confirm that:
z
Data has been saved on the ATCA-7150.
z
No application runs on the ATCA-7150.
z
The ATCA-7150 has quitted the operating system (OS).
3.7.2.1.2 Procedure
To power off the ATCA-7150, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
2. Open the upper and lower ejector handles.
The ATCA-7150 is powered off properly when:
3.7.2.2
z
The HOTSWAP LED blinks at the short blink rate and then is on (blue).
z
The OOS LED is on (red or amber).
z
The HEALTHY LED is off.
Removing the ATCA-7150
To remove the ATCA-7150, proceed as follows:
1. Wear the ESD-preventive wrist strap.
For details, see Wearing the ESD-Preventive Wrist Strap on page 75.
2. Open the upper and lower ejector handles to power off the ATCA-7150, as shown in Figure
3-9.
For details, see Power Off on page 94.
3. Use the screwdriver to unfasten the captive screws anticlockwise, as shown in Figure 3-9.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
95
Hardware Installation of ATCA-7150
4. Remove the ATCA-7150 along the guide rails, as shown in Figure 3-9.
5. Place the ATCA-7150 in the antistatic package.
Figure 3-9
Removing the ATCA-7150
2
1
3
1
2
3.8
Ejector Handles
The ATCA-7150 supports hot swap. As shown in Figure 3-3, the face plate of the ATCA-7150
provides an upper and a lower ejector handles. The ejector handles help to insert, remove,
power on, and power off the ATCA-7150.
Insertion and Removal
96
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Hardware Installation of ATCA-7150
Table 3-7 describes the insertion and removal of the ATCA-7150 by using the ejector handles.
Table 3-7 Insertion and Removal of the ATCA-7150
Operation
Description
Insert the ATCA-7150
The process for inserting the ATCA-7150 is as follows:
Remove the ATCA-7150
z
When the ejector handles are not closed, the HOTSWAP LED is on
and the ATCA-7150 is not powered on.
z
After the ejector handles are closed, the HOTSWAP LED blinks at the
long blink rate and the ATCA-7150 requests for activation.
z
After activation, the ATCA-7150 is powered on and the HOTSWAP
LED is off.
The process for removing the ATCA-7150 is as follows:
z
When you open the ejector handles, the HOTSWAP LED blinks at the
short blink rate and the ATCA-7150 requests for deactivation.
z
After deactivation, the ATCA-7150 is ready for power-off.
z
When the HOTSWAP LED is on, the ATCA-7150 is powered off. At
this time, you can remove the ATCA-7150 by holding the ejector
handles.
Power-On and Power-Off
Table 3-8 describes the power-on and power-off of the ATCA-7150 by using the ejector handles.
Table 3-8 Power-On and Power-Off of the ATCA-7150
Operation
Description
Power on theATCA-7150
Whether you close one ejector handle or both ejector handles, the ATCA7150 can be powered on and work well.
Power off the ATCA-7150
When both ejector handles are opened, you can power off the ATCA7150.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
97
Hardware Installation of ATCA-7150
98
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
A
Troubleshooting
A.1
Appendix: A
Overview
This chapter describes:
A.2
z
Precautions
z
Principles
z
Resources
z
LED Display Exceptions
z
Power-On Startup Exceptions
z
OS Exceptions
Precautions
Before you remove the faults of the ATCA-7150 and RTM-ATCA-7150 suite, be familiar with
the Server System Safety Information shipped with the shelf.
A.3
Principles
During troubleshooting, follow the principles:
z
Diagnose the outside and then the inside.
In troubleshooting, remove the outside faults, such as power interruption and the faults of
the peer device.
z
Diagnose the network and then the NEs (network Elements).
According to the network topology, analyze whether the network environment is normal
and the interconnected device is faulty. Locate the NE to which the fault occurs.
z
Diagnose the high speed part and then the low speed part.
From the alarm signal stream, the alarm of the high speed signal often causes the alarm of
the low speed signal. Therefore, remove the fault of the high speed part first.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
99
Troubleshooting
z
A.4
Analyze the alarm of high level and then that of low level.
Analyze the alarm of high level, such as critical alarm or major alarm. Then, analyze the
alarm of low level, such as minor alarm or warning alarm.
Resources
You can use the following resources for troubleshooting:
z
LEDs
The ATCA-7150 suite provides the following LEDs:
—
Out of Service (OOS) LED
—
In Service (IS) LED
—
Attention (ATN) LED
—
Hotswap (H/S) LED
— Hard Disk (HDD) LED
In addition, the external GE daughter card provides network port LEDs (for two Ethernet
interfaces). The external FC daughter card provides FC status LEDs (for two FC interfaces).
You can monitor the LEDs to diagnose the current status of the ATCA-7150 suite. For
details on the LEDs of the ATCA-7150 suite, see the LED section in the ATCA-7150
Installation and Use manual.
z
A.5
Generating error codes and alarm signals
Error codes and alarm signals help you to further locate and remove the faults.
Contacting Emerson Network Power for
Technical Support
If a problem persists after you handle it under the guidance of this document, contact the local
office or Customer Service Center of Emerson Network Power to obtain timely technical
support. Before you report the problem to Emerson Network Power engineer, collect the
following information:
100
z
Detailed name and address of the customer
z
Contact person and telephone number
z
Time when the fault occurred
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
z
Detailed description on the fault
z
Device type and software version
z
Measures taken after the fault occurred and related results
z
Problem level and required solution time
The contact address of Emerson Network Power is:
Emerson Network Power - Embedded Computing GmbH
Lilienthalstr. 15
85579 Neubiberg-Munich/Germany
A.6
LED Display Exceptions
A.6.1
LEDs Are Off
Description
All LEDs on the ATCA-7150 face plate are off, including the OOS, IS, ATN, H/S, and HDD LEDs.
At the same time, no information is displayed on the KVM.
Solution
To solve the problem, proceed as follows:
1. Check that the ATCA-7150 is properly inserted in the shelf.
2. Check whether the -48 V DC inputs to the shelf are normal.
3. If the PEM of the ATCA-7150 is damaged, replace the ATCA-7150.
4. Contact Emerson Network Power technical support engineer to load the BMC software
again.
A.6.2
In Service (IS) LED Blinks
Description
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
101
Troubleshooting
The IS LED of the ATCA-7150 blinks (red). The alarm severity varies with the blinking frequency.
The higher the blinking frequency, the more serious the alarm.
The IS LED can be green or red. The working state of the ATCA-7150 decides the color of the
LED.
The blinking frequency of the IS LED indicates the alarm level:
z
For a minor alarm, the IS LED blinks at a frequency of 0.5 Hz.
z
For a major alarm, the IS LED blinks at a frequency of 1 Hz.
z
For a critical alarm, the IS LED blinks at a frequency of 4 Hz.
Solution
By using the SMM command, query the status and logs of the blade where the alarm occurs.
If an alarm occurs due to over high temperature, confirm that:
1. The temperature in the equipment room meets the operating requirements for the
product.
2. The air intake vents and exhaust vents of the shelf are not blocked.
3. Blank filler blades are installed in the vacant slots of the shelf.
4. The fans are adjusted to the required speed.
A.7
Power-On Startup Exceptions
Description
After you close the upper and lower ejector handles of the ATCA-7150, the HOTSWAP LED
blinks (blue) and no information is displayed on the KVM.
Solution
To solve the problem, proceed as follows:
1. Check that the ATCA-7150 is properly inserted in the shelf and that its ejector handles are
fully closed.
2. Check that the pointers of the ATCA-7150 rear part that is connected to the backplane are
not damaged or deformed.
102
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
3. Check the power supply of the shelf. If the power is low, the ATCA-7150 cannot be powered
on through the SMM.
4. Check whether the SMM is firmly inserted in the proper position and works well. Make sure
that at least one SMM is present in the shelf and works well.
5. Contact Emerson Network Power technical support engineer to check the IPMC software.
A.8
Component Exceptions
A.8.1
Component Is Unavailable
Description
The optional component that is newly installed cannot be used.
Solution
To solve the problem, proceed as follows:
1. Make sure that this optional component is suitable for the ATCA-7150 suite.
For details, see Optional Components Supported by the ATCA-7150 on page 79.
2. Make sure that the optional component is installed properly.
3. Make sure that any installed device or cable is not loose.
4. Re-install the optional component that is installed just now.
5. Replace the optional component that is installed just now.
For details, see Installing Blade Accessories on page 78.
A.8.2
Number of DIMMs Is Inconsistent
Description
The number of the displayed system DIMMs is less than that of the installed physical DIMMs.
Solution
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
103
Troubleshooting
To solve the problem, proceed as follows:
1. Make sure that all DIMMs of correct type are installed in the slots properly.
2. Check for consistency of the size and frequency of the installed DIMMs.
3. Re-install the DIMMs.
For details, see Installing the DIMM on page 82.
4. Replace the DIMM.
For details, see Replacing the DIMM on page 84.
5. If the problem persists, replace the ATCA-7150.
For details, see Installing and Removing the Blade on page 91.
A.9
Power Exceptions
A.9.1
ATCA-7150 Cannot Be Started
Description
The ATCA-7150 cannot be started.
Solution
To solve the problem, proceed as follows:
1. Make sure that the shelf is powered on properly.
For details, refer to the respective system documentation.
2. If you install an optional component on the ATCA-7150, remove the optional component
and then restart the ATCA-7150.
3. Start another ATCA-7150 in the shelf. If it can be started normally, replace the faulty ATCA7150.
4. If the problem persists, see Uncertain Exceptions on page 109.
104
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
A.9.2
ATCA-7150 Automatically Shuts Down
Description
The ATCA-7150 automatically shuts down without any explicit reason.
Solution
To solve the problem, proceed as follows:
1. Make sure that each component of the shelf is installed properly. For details, refer to the
respective system documentation. If some components are not installed or are installed
improperly, the ATCA-7150 may automatically shut down.
2. Replace the ATCA-7150.
A.10 Peripheral Exceptions
A.10.1 Keyboard Cannot Be Used
Description
All keys or part keys on the keyboard cannot be used.
Solution
To solve the problem, proceed as follows:
1. Make sure that the cable of the keyboard is connected properly and firmly and that the
cable of the keyboard and that of the mouse are not connected reversely.
2. Make sure that the ATCA-7150 is powered on.
For details, see Power-On on page 93.
3. Replace the keyboard. For details, refer to the document shipped with the keyboard that
you use.
4. Replace the RTM of the server blade that works with the ATCA-7150.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
105
Troubleshooting
A.10.2 Mouse Cannot Be Used
Description
The mouse cannot be used.
Solution
To solve the problem, proceed as follows:
1. Make sure that the cable of the mouse is connected properly and firmly and that the cable
of the mouse and that of the keyboard are not connected reversely.
2. Make sure that the mouse works well on other ATCA-7150s.
3. Make sure that the mouse has been properly installed with drivers.
4. Make sure that the ATCA-7150 is powered on and started normally.
5. Replace the mouse.
For details, refer to the document shipped with the mouse that you use.
A.10.3 Monitor Remains Dark
Description
When you connect the monitor to the running ATCA-7150 or start some applications of the
ATCA-7150, the monitor remains dark.
Solution
To solve the problem, proceed as follows:
1. Make sure that the power cable of the monitor is connected properly.
2. Make sure that the monitor is connected to the RTM of the server blade properly and
firmly.
3. Make sure that you have turned on the monitor and properly adjusted the luminance and
contrast control.
4. Power off the ATCA-7150 and then power it on again.
106
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
5. Replace the monitor or ATCA-7150. For details on how to replace the monitor, refer to the
document shipped with the monitor that you use.
For details on how to replace the ATCA-7150, see Installing and Removing the Blade on page
91.
A.10.4 Monitor Display Is Abnormal
Description
Jittering, unreadable, rolling or twisted image is displayed on the monitor screen.
Solution
To solve the problem, proceed as follows:
1. If monitor self-test indicates that the monitor works normally, consider the position of the
monitor. The magnetic field around other devices (such as transformers, electronic
devices, fluorescent lights, and other monitors) may cause screen jitters, image
fluctuation, or unreadable, rolling or twisted image.
2. Close the monitor if this condition happened. When you move a color monitor, the color of
the screen may be distorted. Move the device and monitor. Make sure that the distance
between them is at least 305 mm.
3. Turn on the monitor. If the problem persists, replace the monitor or ATCA-7150. For details
on how to replace the monitor, refer to the document shipped with the monitor that you
use.
For details on how to replace the ATCA-7150, see Installing and Removing the Blade on page
91.
A.10.5 No Information Is Displayed on the Monitor
Description
The ATCA-7150 LED is normal and no alarm is generated. However, no information is displayed
on the monitor.
Solution
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
107
Troubleshooting
To solve the problem, proceed as follows:
1. Make sure that:
z
The RTM of the server blade is inserted properly.
z
The upper and lower ejector handles are fully closed.
z
The LEDs are in normal state.
2. Make sure that the cable connectors of the monitor contact well.
3. Check whether the DIMM is inserted.
4. If the DIMM is inserted, check whether it is inserted in the memory slot firmly.
5. If the problem persists, replace the DIMM with a new one.
For details, see Replacing the DIMM on page 84.
A.11 Other Exceptions
A.11.1 USB Interface Cannot Be Used
Description
The USB interface cannot be used.
Solution
To solve the problem, proceed as follows:
1. Make sure that the USB device drivers are installed properly.
2. Make sure that the OS that you use supports the USB device.
A.11.2 Network Connection Is Faulty
Description
One or more ATCA-7150 cannot communicate with the external network.
Solution
108
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
To solve the problem, proceed as follows:
1. Make sure that the network module that you use is installed in the server system and works
normally. For details, refer to the respective system documenation.
2. The setting in the network module is suitable for the ATCA-7150. For details, refer to the
respective system documentation.
3. If the problem persists, see Uncertain Exceptions on page 109.
A.11.3 A Fault Occurs in Software
Description
A fault may occur in software.
Solution
To solve the problem, proceed as follows:
1. Check whether the problem is caused by software fault.
2. Check whether the ATCA-7150 has the minimum memory required by the software.
3. Check whether the design of the software is applied to the server.
4. Check whether other software can run on the ATCA-7150.
5. Check whether this software can run on other ATCA-7150s.
6. If an error message is generated when you use the software, refer to the document
shipped with the software to get the details on the message and solution.
7. Contact Emerson Network Power technical support engineer to handle the problem.
A.12 Uncertain Exceptions
When you diagnose the faulty ATCA-7150, check whether the ATCA-7150 or the shelf has a
fault.
z
If all ATCA-7150s have the same symptom, it is very likely that a fault occurs in the shelf.
For details, refer to the respective system documentation.
z
If the shelf has multiple ATCA-7150s and one ATCA-7150 is faulty, troubleshoot the faulty
ATCA-7150.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
109
Troubleshooting
If you think that the fault is caused by software, see A Fault Occurs in Software on page 109.
Damaged CMOS data or BIOS codes may cause some uncertain problems. To reset the CMOS
data, contact Emerson Network Power for technical support. For detailed contact methods,
see Contacting Emerson Network Power for Technical Support on page 100.
Check whether the PEM of the shelf works well. If the PEM works well but the problem persists
after you install the ATCA-7150 again, proceed as follows:
1. Make sure that the ATCA-7150 is inserted in the proper slot of the shelf. The ATCA-7150 is
installed in one of the slots 1-6 or 9-14 at the front side of the shelf.
2. Make sure that the external cables that the ATCA-7150 and its RTM use are properly
connected.
3. Power off the ATCA-7150 and remove it from the shelf.
4. Remove or disconnect the following devices (one at a time) until you find the fault. Reinstall and power on the ATCA-7150.
a.
SOL daughter card
b. Hard disk drive
c. DIMM
The hardware configurations enough to start the ATCA-7150 include:
z
Main board
z
One CPU
z
One 512 MB DIMM
When the ATCA-7150 is configured with only one DIMM, the DIMM can be installed in DIMM
interface 0 only. For the postion of the DIMM interface, see Figure 3-3.
110
z
One hard disk
z
Available shelf
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
5. Install and power on the ATCA-7150. If the problem persists, replace the following
components in order:
a.
Hard disk
b. DIMM
c.
CPU
d. Main board
6. If the ATCA-7150 passes all system tests, a fault may occurs in the external network
connection.
A.13 POST Code Checkpoints
POST code checkpoints are the largest set of checkpoints during the BIOS pre-boot process.
Table A-1 lists the types of checkpoints that may occur during the POST stage of the BIOS and
related solutions.
To clear the CMOS RAM or upgrade the BIOS, contact Emerson Network Power for technical
support.
Table A-1 POST code checkpoints
Checkpoint
Description
Solution
03
Disable NMI, parity, video for EGA, and
DMA controllers.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
Initialize:
z
BIOS, POST, and runtime data area
z
BIOS modules on POST entry and
GPNV area
z
CMOS
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
111
Troubleshooting
Table A-1 POST code checkpoints (continued)
Checkpoint
Description
Solution
04
Check the CMOS diagnostic byte to
determine whether battery power is
proper and whether the CMOS
checksum is proper. Verify the CMOS
checksum by reading the storage area. If
the CMOS checksum is wrong, update
CMOS with power-on default values and
clear passwords. Initialize data variables
that are based on CMOS setup
questions.
1.
Restart the ATCA-7150.
2.
Clear CMOS and then restart the
ATCA-7150.
3.
Replace the ATCA-7150.
05
Initialize the interrupt controlling
hardware and interrupt vector table.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
06
Initialize the system timer. Initialize the
handler for system timer interrupt.
08
Initialize the keyboard controller (KBC).
1.
Restart the ATCA-7150
C0
Early CPU initialization starts.
2.
Replace the ATCA-7150.
C1
Set the boot processor initialization
information.
C2
Set the boot processor initialization for
POST.
C5
List and set application processors.
C6
Re-enable cache for the boot processor.
C7
Exit the early CPU initialization.
0A
Initialize the 8042 compatible KBC.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
0B
Detect the presence of PS/2 mouse.
1.
Restart the ATCA-7150
0C
Detect the presence of the keyboard in
KBC port.
2.
Replace the PS/2 mouse and
restart the ATCA-7150.
3.
Replace the ATCA-7150.
1.
Restart the ATCA-7150.
2.
Upgrade the BIOS and restart the
ATCA-7150.
3.
Replace the ATCA-7150.
0E
112
Test and initialize different input
devices. Also, update kernel variables.
Disable handler for IRQ1 installation.
Uncompress all available languages,
BIOS logo, and silent logo modules.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
Table A-1 POST code checkpoints (continued)
Checkpoint
Description
Solution
13
Initialize early POST chipset registers.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
24
1.
Restart the ATCA-7150.
2.
Upgrade the BIOS and restart the
ATCA-7150.
3.
Replace the ATCA-7150.
Initialize system management interrupt.
1.
Restart the ATCA-7150.
2C
Initialize different devices. Detect and
initialize the video adapter that is
installed in the system and has optional
ROMs.
2.
Replace the ATCA-7150.
2E
Initialize all output devices.
31
Allocate memory for the ADM module
and uncompress it. Control the ADM
module for initialization. Initialize the
language and font modules for ADM.
Activate the ADM module.
1.
Restart the ATCA-7150.
2.
Upgrade the BIOS and restart the
ATCA-7150.
3.
Replace the ATCA-7150.
33
Initialize the silent boot module. Set the
window for displaying text information.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
37
Display the sign-on message, CPU
information, setup key message, and
any OEM specific information.
39
Initializes DMA controller 1 and DMA
controller 2.
3A
Initialize RTC date and time.
1.
Restart the ATCA-7150.
2.
Clear CMOS RAM and then restart
the ATCA-7150.
3.
Replace the ATCA-7150.
30
Uncompress and initialize the specific
BIOS modules of any platform.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
113
Troubleshooting
Table A-1 POST code checkpoints (continued)
Checkpoint
Description
Solution
3B
Test for total memory installed in the
system. Also, Check for the Delete or
ESC key to limit memory test. Display
total memory in the system.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
1.
Restart the ATCA-7150.
2.
Upgrade the BIOS and restart the
ATCA-7150.
3.
Replace the ATCA-7150.
1.
Restart the ATCA-7150.
2.
Check whether the BIOS write
protection is enabled. If it is
enabled, disable it and restart the
ATCA-7150.
3.
Replace the ATCA-7150.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
3C
Initialize Mid POST chipset registers.
40
Detect different devices (such as parallel
ports, serial ports, and coprocessor in
CPU) successfully installed in the system
and update the BDA, EBDA, and so on.
50
Program the memory hole or any kind
of implementation that needs an
adjustment in system RAM size if
needed.
52
Update CMOS RAM memory size from
the memory found in memory test.
Allocate memory for the extended BIOS
data area from base memory.
60
Initialize NumLock status and program
the keyboard typematic rate.
75
Initialize Int-13 and prepare for IPL
detection.
78
Initialize IPL devices controlled by BIOS
and optional ROMs.
7A
Initialize remaining optional ROMs.
7C
84
114
Generate and write contents of ESCD in
NVRam.
Record errors encountered during POST.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
Table A-1 POST code checkpoints (continued)
Checkpoint
Description
Solution
85
Display errors to the user and get the
user response for errors.
Handle the fault according to the
prompts displayed on the terminal.
8C
Initialize late POST chipset registers.
1.
Restart the ATCA-7150.
8D
Build ACPI tables (if ACPI is supported).
2.
Replace the ATCA-7150.
8E
Program peripheral parameters. Enable
or disable NMI as selected.
90
Initialize late POST of system
management terminal.
A1
Perform clean-up work needed before
booting to the OS.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
1.
Restart the ATCA-7150.
A2
Take care of runtime image preparation
for different BIOS modules. Initialize the
IRQ routing table. Prepare the runtime
language module. Disable the system
configuration display if needed.
A4
Prepare the runtime language module.
A7
Display the system configuration screen
if enabled. Initialize the CPU's system
configuration screen before booting,
which includes the programming of the
MTRR's.
A8
Prepare CPU for OS booting, including
final MTRR values.
AC
End POST initialization of chipset
registers.
2.
Replace the CPU.
3.
Replace the ATCA-7150.
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
A.14 DIM Code Checkpoints
The device initialization manager (DIM) gets control at various time during BIOS POST to
initialize different system buses.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
115
Troubleshooting
Table A-2 lists the checkpoints where the DIM module is accessed and solutions.
116
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
Troubleshooting
Table A-2 DIM code checkpoints
Checkpoint
Description
Solution
2A
Initialize different buses and perform
the following functions:
1.
Restart the ATCA-7150.
2.
Replace the ATCA-7150.
z
Reset, Detect, and Disable
(function 0)
z
Static Device Initialization
(function 1)
z
Boot Output Device Initialization
(function 2)
Function 0 disables all device nodes, PCI
devices, and PnP ISA cards. It also
assigns PCI bus numbers.
Function 1 initializes all static devices
that include manually configured
onboard peripherals, memory and I/O
decode windows in PCI-PCI bridges, and
noncompliant PCI devices. Static
resources are also reserved.
Function 2 searches for and initializes
any PnP, PCI, or AGP video devices.
38
Initialize different buses and perform
the following functions:
z
Boot Input Device Initialization
(function 3)
z
IPL Device Initialization (function 4)
z
General Device Initialization
(function 5)
Function 3 searches for and configures
PCI input devices and detects whether
the system has the standard keyboard
controller.
Function 4 searches for and configures
all PnP and PCI boot devices.
Function 5 configures all onboard
peripherals that are set to an automatic
configuration and configures all
remaining PnP and PCI devices.
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
117
Troubleshooting
A.15 ACPI Code Checkpoints
ACPI checkpoints are displayed when an ACPI capable OS either enters or leaves a sleep state.
Table A-3 lists the types of checkpoints that may occur during ACPI sleep or wake states and
solutions.
Table A-3 ACPI code checkpoints
Checkpoint
Description
Solution
AC
First ASL check point. Indicate that the
system is running in ACPI mode.
1.
Restart the ATCA-7150.
2.
Install the OS and drivers.
AA
Indicate that the system is running in
ACPI mode.
01, 02, 03, 04, 05
Enter sleep state S1, S2, S3, S4, or S5.
1.
Restart the ATCA-7150.
Wake from sleep state S1, S2, S3, S4,
or S5.
2.
Install the OS and drivers again.
3.
Upgrade the BIOS and restart the
ATCA-7150.
10, 20, 30, 40, 50
118
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
B
Appendix: B
Related Documentation
B.1
Emerson Network Power - Embedded
Computing Documents
The Emerson Network Power - Embedded Computing publications listed below are referenced
in this manual. You can obtain electronic copies of Emerson Network Power - Embedded
Computing publications by contacting your local Emerson sales office. For documentation of
final released (GA) products, you can also visit the following website:
http://www.emersonnetworkpowerembeddedcomputing.com > Solution Services >
Technical Documentation Search. This site provides the most up-to-date copies of Emerson
Network Power - Embedded Computing product documentation.
Table B-1 Emerson Network Power - Embedded Computing Publications
B.2
Document Title and Source
Publication Number
RTM-ATCA-7150 Installation and Use Manual
6806800E87
ATCA-7150: Control via IPMI, Programmer's Reference
6806800E85
MESC-RTM-7150-FC Installation Information
6806800F90
MESC-RTM-7150-GE Installation Information
6806800F89
ATCA-7X50-HDDx-SAS/SATA Installation Information
6806800E28
ATCA-7x50-MEM Installation Information
6806800E27
Related Specifications
For additional information, refer to the following table for related specifications. As an
additional help, a source for the listed document is provided. Please note that, while these
sources have been verified, the information is subject to change without notice.
Table B-2 Related Specifications
Organization
Document Title
Intel
Platform Management FRU Information Storage
Definition v1.0
developer.intel.com/design/servers/ipmi
IPMI Specification v2.0
Intel
IPMI Spceification V2.0
developer.intel.com/design/servers/ipmi
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
119
Related Documentation
Table B-2 Related Specifications (continued)
Organization
Document Title
PICMG
PICMG 3.0 Revision 2.0 Advanced TCA Base
Specification
picmg.org/specifications.stm
PICMG 3.1 Revision 1.0 Specification Ethernet/Fiber
Channel
120
ATCA-7150 and RTM-ATCA-7150 Getting Started (6806800G42B)
HOW TO REACH LITERATURE AND TECHNICAL SUPPORT:
Tempe, Arizona, USA
1 800 759 1107
1 602 438 5720
Munich, Germany
+49 89 9608 0
For literature, training, and technical assistance and support programs, visit
www.emersonnetworkpowerembeddedcomputing.com
Emerson Network Power.
The global leader in enabling Business-Critical Continuity™
AC Power Systems
Connectivity
DC Power Systems
Embedded Computing
Embedded Power
Integrated Cabinet Solutions
www.emersonnetworkpowerembeddedcomputing.com
Outside Plant
Power Switching & Control
Precision Cooling
Services
Site Monitoring
Surge & Signal Protection
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.
All other product or service names are the property of their respective owners.
© 2008 Emerson Electric Co.
Download PDF

advertising