Owner`s manual | Emerson EWC19T5 TV VCR Combo User Manual

OWNER’S
MANUAL
“EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.”
COLOR TV/VCR/DVD TRIPLE COMBO
EWC19T5
(19 inch)
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-256-2487.
Or visit our WEB SITE at http://www.EmersonAudioVideo.com
Please read before using this equipment
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
AMEUBLES- Cet appareil ne doit SYMBOLE D'AVERTISSEMENT POUR
être placé que sur un meuble (avec APPAREILLESETCOMPOSANTES
MEUBLE A ROULETTES
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation
d’une force excessive et des surS3126A
faces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug the unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by
the unit manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this unit near water-for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and
the like.
8.Accessories-Do not place this unit on an unstable cart,
stand, tripod, bracket, or table. The unit may fall, causing
serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the unit.
Any mounting of the appliance
PORTABLE CART WARNING
should follow the manufacturer’s
instructions and should use a mounting accessory recommended by the
manufacturer. An appliance and cart
combination should be moved with
care. Quick stops, excessive force,
and uneven surfaces may cause the
S3126A
appliance and cart combination to
overturn.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the unit and to protect it from overheating, and
these openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed,
sofa, rug, or other similar surface. This unit should never be
placed near or over a radiator or heat register. This unit
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
10.Power Sources-This unit should be operated only from the
type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For the
units intended to operate from battery power, or other
sources, refer to the operating instructions.
11.Grounding or Polarization-This unit is equipped with a
polarized alternating-current line plug(a plug having one
blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
-2-
EN
F IGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECT RICAL CODE
ANTE NNA
L EAD I N
WI RE
GROUND
CLAMP
A NTENNA
DI SCHARG E UN I T
(NEC SECTION 8 10 -2 0)
EL ECT RI C
SE RV I CE
EQ U I PM EN T
G RO UNDI NG CO NDUCT ORS
(NEC SECTION 8 10 -2 1)
G RO UND CL AM PS
NEC - NATI O NAL EL ECTRI CAL CO DE
POWER SERVI C E G RO UNDI NG
EL EC TR O DE SYST EM
(NEC ART 2 50 , PART H)
S2 8 9 8 A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the unit, be sure the antenna
or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
19.Damage Requiring Service-Unplug this unit from the wall
outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
unit.
c. If the unit has been exposed to rain or water.
14.Lightning-For added protection for this unit receiver during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the unit due to lightning and power-line
surges.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the
unit.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment
of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the unit to its normal operation.
e. If the unit has been dropped or damaged in any way.
f. When the unit exhibits a distinct change in performance,
this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to
this unit, ask the service technician to perform routine safety checks to determine that the unit is in proper operating
condition.
22.Heat-This unit product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this unit yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
-3-
EN
PRECAUTIONS
LASER SAFETY
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to service this device, due to possible eye injury.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other unit has the same serial
number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
-4-
EN
LOCATION
WARNING
For safe operation and satisfactory performance of
your unit, keep the following in mind when selecting
a place for its installation:
• Shield it from direct sunlight and keep it away from
sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top or bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
• Be sure to remove a disc and unplug the AC power
cord from the outlet before carrying the unit.
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a unit which has
moisture, it may damage the DVD and the unit.
Therefore when the condensation occurs inside the
unit, turn the unit on and allow at least 2 hours for the
unit to dry out.
•
•
The following symbols below appear in some headings and notes in this manual, with the following
meanings
TV/VCR
: Description refers to TV/VCR operation (in the
TV/VCR mode).
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting
•
SYMBOLS USED IN THIS MANUAL
CD
: Description refers to playback of Audio CDs
(in the DVD mode).
QUICK
it from an AC wall outlet. Grasp it by the plug.
If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the unit disc
loading tray.
Do not place anything directly on top of the unit.
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
SUPPLIED ACCESSORIES
Remote Control Unit
Batteries
Owner’s Manual
Owner's Manual
NE211UD
2 AA Batteries
1EMN20210
• If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our
help line mentioned on the front page.
• Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
-5-
EN
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . .2
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C SUPPLIED ACCESSORIES . . . . . . .5
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .9
INSTALLING THE BATTERIES . .11
C PREPARATION FOR USE . . . . . . .12
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .12
CONNECTING TO FRONT A/V
INPUT JACKS . . . . . . . . . . . . . . . .13
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS (for DVD) . . .13
CONNECTING TO A DOLBY
DIGITAL DECODER (for DVD) . .14
C SPECIAL PLAYBACK . . . . . . . . . .24
RENTAL PLAYBACK . . . . . . . . . .24
AUTO REPEAT PLAYBACK . . . . .24
C SEARCH . . . . . . . . . . . . . . . . . . . . .25
ZERO RETURN . . . . . . . . . . . . . . .25
PICTURE SEARCH . . . . . . . . . . . .25
TIME SEARCH . . . . . . . . . . . . . . .25
INDEX SEARCH . . . . . . . . . . . . . .26
C SPECIAL FEATURES . . . . . . . . . .27
REAL TIME TAPE COUNTER . . .27
AUTO REWIND-EJECT . . . . . . . .27
C RECORDING . . . . . . . . . . . . . . . . .28
NORMAL RECORDING . . . . . . . .28
SKIPPING UNWANTED SCENES
DURING RECORDING . . . . . . . . .28
OTR (One Touch Recording) . . . . . .29
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .29
C TIMER RECORDING . . . . . . . . . . .30
AUTOMATIC
TIMER RECORDING . . . . . . . . . .30
AUTO RETURN . . . . . . . . . . . . . . .32
C ON SCREEN DISPLAY . . . . . . . . .33
TV/VCR SECTION
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .33
C TV OPERATION AND SETTINGS .15
WATCHING A TV PROGRAM . . .15
DEGAUSSING . . . . . . . . . . . . . . . .15
PICTURE CONTROL . . . . . . . . . . .15
SLEEP TIMER . . . . . . . . . . . . . . . .16
CLOSED CAPTION SYSTEM . . . .16
CHANNEL SET UP . . . . . . . . . . . .17
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . . . . .18
DAYLIGHT-SAVING TIME . . . . . .19
V-CHIP SET UP . . . . . . . . . . . . . . .20
TV RATING SET UP . . . . . . . . .20
MPAA RATING SET UP . . . . . .21
CHANGE ACCESS CODE . . . . .21
MENU LANGUAGE . . . . . . . . . . .21
DVD SECTION
C VIDEO CASSETTE . . . . . . . . . . . . .22
C PLAYBACK . . . . . . . . . . . . . . . . . . .23
NORMAL PLAYBACK . . . . . . . . .23
TRACKING ADJUSTMENT . . . . .23
SLOW MOTION . . . . . . . . . . . . . .23
STILL PICTURE . . . . . . . . . . . . . .23
VERTICAL HOLD CONTROL . . .23
C SEARCH FUNCTION . . . . . . . . . . .37
TRACK SEARCH . . . . . . . . . . . . .37
TITLE / CHAPTER SEARCH . . . .37
TIME SEARCH . . . . . . . . . . . . . . .37
MARKER SETUP SCREEN . . . . . .37
C SPECIAL PLAYBACK FUNCTION . . .38
REPEAT . . . . . . . . . . . . . . . . . . . . .38
PROGRAM . . . . . . . . . . . . . . . . . . .38
RANDOM PLAYBACK . . . . . . . . .38
C CHANGING THE SETTINGS . . . .39
SUBTITLE LANGUAGE . . . . . . . .39
AUDIO LANGUAGE . . . . . . . . . . .39
STEREO SOUND MODE . . . . . . . .39
CAMERA ANGLE . . . . . . . . . . . . .40
BLACK LEVEL SETTING . . . . . . .40
VIRTUAL SURROUND . . . . . . . . .40
C THE ON-SCREEN INFORMATION . . .41
C CHANGING THE DVD SET UP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .42
CUSTOM MENU . . . . . . . . . . . . . .42
LANGUAGE SETTING . . . . . . .42
DISPLAY SETTING . . . . . . . . . .43
AUDIO SETTINGS . . . . . . . . . .43
PARENTAL CONTROL . . . . . . .44
OTHER SETTINGS . . . . . . . . . .44
INITIALIZE . . . . . . . . . . . . . . . . . .44
C TROUBLESHOOTING GUIDE . . .45
C ABOUT THE DISCS . . . . . . . . . . . .34
PLAYABLE DISCS . . . . . . . . . . . .34
UNPLAYABLE DISCS . . . . . . . . . .34
C PLAYING A DISC . . . . . . . . . . . . . .35
BASIC PLAYBACK . . . . . . . . . . . .35
GENERAL FEATURES . . . . . . . . .35
DISC MENU . . . . . . . . . . . . . . . . .35
TITLE MENU . . . . . . . . . . . . . . . . .35
RESUME . . . . . . . . . . . . . . . . . . . .36
PAUSE . . . . . . . . . . . . . . . . . . . . . .36
STEP BY STEP PLAYBACK . . . . .36
FAST FORWARD /
FAST REVERSE . . . . . . . . . . . . . .36
SLOW FORWARD /
SLOW REVERSE . . . . . . . . . . . . . .36
ZOOM . . . . . . . . . . . . . . . . . . . . . .36
-6-
C MAINTENANCE . . . . . . . . . . . . . . .48
DISC HANDLING . . . . . . . . . . . . .48
C SPECIFICATIONS . . . . . . . . . . . . .49
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .50
C WARRANTY . . . . . . . . . . .Back Cover
EN
FEATURES
TV/VCR Mode
• Rotary 4-head Record/Playback System–Four
•
•
heads ensure excellent picture quality and special
effects playback.
Index Search–Fast-forwards to start of next recording.
Slow Motion–View recorded program at slower
than normal speed.
• Infrared remote control
• Trilingual on screen TV/VCR setup display
• Three different playback tape speeds : SP/LP/SLP
• Two different recording tape speeds : SP/SLP
• Auto Head Cleaner–Automatically cleans video
•
•
•
selectable in English, Spanish or French
• Real time counter–This shows the elapsed recording or playback time in hours, minutes and seconds. The “–” indication will appear when the tape
is rewound further than the tape counter position
“0:00:00”.
•
• 181 channel capability PLL frequency synthesiz-
•
•
er tuner with direct station call (A converter may
be necessary to view scrambled cable channels.)
• Auto Clock Setting–Allows you to set the clock
•
•
function from a PBS broadcast station.
Closed Caption Decoder–You may view specially
labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or
text display added to the program.
Auto power on and off system–Automatically
turns on the unit when you insert the cassette, turns
off after auto-rewind and ejects when the beginning of the tape is reached.
• Auto rewind when the end of a tape is reached
•
•
(This function doesn’t occur when using timer
recording.)
Smooth mode change–TV/VCR mode and DVD
mode automatically changes without control.
2 Step picture search operation–You can view a
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode, only high speed is available.
•
heads as you insert or remove a cassette.
Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without hitting [PLAY O].
Time search–Lets you set the unit to advance the
tape by entering the desired playback time you want
to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible by
hitting [REC/OTR].
• 1 Year, 8 events (including Daily and Weekly)
Timer Recording–The built-in timer allows you to
•
•
•
•
-7-
record up to 8 programs at different times on different channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broadcasts and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Auto return–After timer recording is finished, the
unit can return to the beginning of the recording.
Sleep timer–Allows you to have the unit automatically turn off at a desired time.
Timer Program Extension–Allows you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
EN
DVD Mode
¡Dolby Digital sound
¡On-screen display
This unit can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby
Digital decoder.
Information about the current operation can be displayed on a TV screen, allowing you to confirm the
currently active functions (such as program playback), on the TV screen using the remote control.
¡Still/fast/slow/step playback
Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
¡Random playback for Audio CD
This unit can shuffle the order of tracks to play them
in random order.
¡Search
Chapter search / Title search / Track search / Time
search
¡Repeat
Chapter / Title / Track / All / A-B
¡Zoom
¡Program playback for Audio CD
You can program the order of tracks to play them in
any desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no
input from the unit for 5 minutes in the stop mode.
After the screen saver program is activated for 15
minutes, the power automatically turns off.
Magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available
on a disc.
¡Parental lock
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This unit automatically detects if the loaded disc is
DVD or Audio CD.
-8-
EN
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - [Fig.1]
DVD buttons
buttons
DVD
POWER
VOLUME
SKIP
SKIP
PLAY
STOP
TV/VCR buttons
CHANNEL
SELECT
OPEN/CLOSE
REC/OTR
REW
PLAY
F.FWD
STOP/EJECT
HEADPHONE VIDEO
DVD
SEARCH
1
2
3 4 3
5
6
7 8 9 10
- REMOTE CONTROL - [Fig. 2]
POWER PICTURE
1
22
23
1
2
3
4
5
6
7
8
27
28
29
30
31
32
33
SPEED
SELECT
9
44
CH.
11
VOL.
2
9
+100
PAUSE
24
25
26
(DVD) 3
(TV/VCR) 14
4
13
SLEEP
0
+10
C.RESET
ZOOM
MUTE
PLAY
STOP
DISC
MENU
RECORD
DISPLAY
ENTER
SETUP
TITLE
RETURN
CLEAR SEARCH MODE REPEAT
A-B
AUDIO
ANGLE
MODE
SUBTITLE
43
42
3 (DVD)
15 (TV/VCR)
5
41
40
39
38
37
36
35
34
L
AUDIO
R
TV/VCR
11 12 13 14 4 15
16 17 18 19
20 21
5. C STOP Button [TV/VCR P.23 / DVD P.35]
(Front panel) Stops operation of the disc.
(Remote control) Stops operation of the disc or
tape contents.
6. A OPEN/CLOSE Button [DVD P.35]
Hit to insert a disc into or remove it from the tray.
7. Disc loading tray
8. DVD Indicator
Lights up during DVD mode.
9. SELECT Button [TV/VCR P.15] [DVD P.35]
Hit to change to TV/VCR mode, external input
mode or DVD mode. You can see the mode
(TV/VCR or DVD) on the front panel indicator.
10.TV/VCR Indicator
Lights up during TV/VCR mode.
11. CHANNEL (CH.) K / L Buttons
Press to select memorized channels.
12. Recording Indicator
Flashes during recording. Lights up in the standby mode for Timer Recording.
13. REC/OTR Button (Front Panel) [TV/VCR P.29]
Hit to start manual recording. Hit repeatedly to
start One Touch Recording.
RECORD Button (Remote Control) [TV/VCR P.28]
Hit to start manual recording.
14. E REW Button (for TV/VCR) [TV/VCR P.25]
Hit to rewind the tape or to view the picture rapidly in reverse during playback mode. (Rewind
Search)
15. F.FWD D Button (for TV/VCR) [TV/VCR P.25]
Hit to rapidly advance the tape or to view the picture rapidly in forward during playback mode.
(Forward Search)
16. C A STOP/EJECT Button [TV/VCR P.22, 25]
Hit to stop the tape motion. Hit in the stop mode
to remove tape from the unit.
17. Remote sensor window
18. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
1. POWER Button [TV/VCR P.15 / DVD P.35]
Hit to turn the power on and off.
2. VOLUME (VOL.) K / L Buttons
Press to control the volume level for the DVD and TV.
3. SKIP H / G Buttons (for DVD) [DVD P.37]
Press once to skip chapters or tracks to a desired
point.
SEARCH E / D Buttons (for DVD) [DVD P.36]
Press and hold to change forward or reverse playback speed.
4. B PLAY Button [TV/VCR P.23 / DVD P.35]
Starts playback of the disc or tape contents.
-9-
EN
- REAR PANEL - [Fig.3]
AUDIO OUT
COAXIAL
ANT.
45
46
47
19. VIDEO input Jack
Connect to the video output jack of a video
camera or VCR.
20. AUDIO L/R input Jacks
Connect to the audio output jacks of a video
camera or VCR.
21. Cassette compartment
22. PICTURE Button
Hit to adjust the picture.
23. Number Buttons
TV/VCR Mode:[P.17]
Press two digits to directly access the desired
channel.
Remember to hit [0] before a single digit channel.
+100 Button–
Hit to select cable channels which are higher than
99.
DVD Mode:[P.37]
Hit to enter the desired number.
+10 Button–
Hit to enter the desired numbers which are higher
than 9.
24. PAUSE F Button [TV/VCR P.23 / DVD P.36]
Pauses the current disc or tape operation.
25. SPEED Button [TV/VCR P.28]
Hit to choose the desired recording speed:
SP/SLP.
26. C.RESET Button [TV/VCR P.25]
Hit to reset counter to “0:00:00”.
Hit to cancel a setting of timer program. (Refer to
page 31.)
27. DISPLAY Button
30. CLEAR Button [DVD P.37]
Hit to clear or cancel a setting currently entered.
31. MODE Button [DVD P.38]
Hit to call up the program screen or the random
screen in the stop mode.
Hit to call up the Black Level Setting screen or
the Virtual Surround screen during playback.
32. SEARCH MODE Button [DVD P.37]
Hit to locate a desired point.
33. AUDIO Button [DVD P.39]
Hit to select a desired audio language or sound
mode.
34. SUBTITLE Button [DVD P.39]
Hit to select a desired subtitle language.
35. REPEAT Button [DVD P.38]
Repeats playback of the current disc, title, chapter,
or track.
36. ANGLE Button [DVD P.40]
Hit to change the camera angle to see the sequence
being played back from a different angle (if available).
37. A-B Button [DVD P.38]
Repeats playback of a selected section.
38. RETURN Button [TV/VCR P.31] [DVD P.37]
Returns to the previous screen in the setup menu.
39. ENTER Button [TV/VCR P.16] [DVD P.35]
Hit to accept a setting.
40. K / L / { / B Buttons
TV/VCR Mode:[P.15]
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
TV/VCR Mode:[P.33]
DVD Mode:[P.35]
Displays the counter or the current channel number and current time on the TV screen.
Press to select a menu item.
DVD Mode:[P.41]
Displays the current status on the TV screen.
28. SETUP Button [TV/VCR P.16] [DVD P.42-44]
Hit to enter or exit the setup menu of TV or DVD.
29. TITLE Button [DVD P.35]
Displays the title menu.
41. DISC MENU Button [DVD P.35]
Calls up the DVD menu.
42. ZOOM Button [DVD P.36]
Enlarges part of a DVD-reproduced image.
43. MUTE Button [TV/VCR P.15]
Mutes the sound. Hit it again to restore sound.
44. SLEEP Button [TV/VCR P.16]
Sets the Sleep Timer.
- 10 -
EN
45. ANT(ENNA). Jack
Connect to an antenna, cable system or satellite
system.
46. Power cord
Connect to a standard AC outlet (120V/60Hz).
47. AUDIO OUT COAXIAL Jack
Connect to the digital input of an external
amplifier or decoder (for DVD Audio only).
NOTE:
•
Remove the power cord from the hook to
avoid breaking a wire before you connect to a
standard AC outlet.
NOTE:
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated
in the battery compartment. Reversed batteries
may cause damage to the device.
• Do not mix different types of batteries together
(e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of
time, remove the batteries to prevent damage or
injury from possible battery leakage.
• Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture.
- 11 -
EN
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
Cables used here are commercially available.
[ANTENNA CONNECTION]
[CATV/SATELLITE CONNECTION]
75-ohm
Coaxial Cable
CATV Box or
Satellite Box *
VHF/UHF
VHF
VHF/UHF
Combiner
OR
OUT
AUDIO OUT
COAXIAL
ANT.
UHF
Flat twinlead cable
OR
ANT.
OR
IN
From Cable System or
Satellite Antenna
75-ohm
Coaxial Cable
From Cable System
VHF
VHF
or
or
UHF
UHF
Adaptor
*Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
[Fig. 4]
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
NOTE:
• Before plugging the antenna into the ANT. jack of the unit, check that the pin is
not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the
ANT. jack of the unit.
VHF/UHF COMBINED ANTENNA
A VHF UHF 75 ohm combination antenna can be
connected to ANT. jack of the unit.
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Bent pin
Cable
Plug
(Needs to be
straightened)
(Straight pin)
CABLE WITH CONVERTER/DESCRAMBLER BOX OR SATELLITE BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown above.
Channel selection must be made with the converter
box or satellite box. This means that channels cannot
be changed using the remote control of this unit.
Use this connection if your cable system connects
directly to the unit without a converter box.
NOTE:
• For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack
before moving the unit.
- 12 -
EN
CONNECTING TO FRONT A/V INPUT JACKS
When you watch a program recorded on another source (VCR or video camera), use the
Audio/Video input jacks on the front of the unit.
Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO
jacks of this unit.
Then press [SELECT] or [CH. K / L] until “AUX” appears on the screen.
POWER
VOLUME
SKIP
PLAY
SKIP
STOP
CHANNEL
SELECT
OPEN/CLOSE
REC/OTR
REW
PLAY
F.FWD
AUX
STOP/EJECT
HEADPHONE VIDEO
SEARCH
DVD
L
AUDIO
R
TV/VCR
ex.
VCR or video camera, etc.
To the Audio output jacks
Audio cable
(commercially available)
(OUT)
(IN)
HEADPHONE VIDEO
To the Video output jack
AUDIO
R
[Front of the unit]
Video cable
(commercially available)
(OUT)
L
(IN)
[Fig. 5]
NOTE:
• When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the
monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R
channel equally.
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS (for DVD)
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
AUDIO OUT
COAXIAL
ANT.
ex.
MD deck, DAT deck, etc.
To Coaxial digital
Audio input jack
To AUDIO OUT
COAXIAL jack
(Only DVD AUDIO OUT)
Audio coaxial digital cable
(commercially available)
(IN)
(OUT)
[Fig. 6]
NOTES:
• The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner’s Manuals for the components to be connected to the unit.
• Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to page 43.)
- 13 -
EN
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a
DOLBY DIGITAL Data stream from its AUDIO OUT COAXIAL jack. By hooking the unit up to a Dolby
Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround
sound as enjoyed in movie theaters.
Use audio coaxial digital cables (commercially available) for the audio connections.
Front speaker
(left)
Center
speaker
Dolby Digital
decoder
Surround
speaker
(left)
Front speaker
(right)
AUDIO OUT
COAXIAL
ANT.
To AUDIO OUT
COAXIAL jack
(Only DVD AUDIO OUT)
To Coaxial digital
Audio input jack
Surround
speaker
(right)
Subwoofer
(OUT)
(IN)
Audio coaxial digital cable
(commercially available)
[Fig. 7]
NOTES:
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner’s Manuals for the components to be connected to the unit.
• If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the
setup mode. (Refer to page 43.)
• Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the
setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the
speakers. (Refer to page 43.)
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
- 14 -
EN
TV/VCR SECTION
TV OPERATION AND SETTINGS
WATCHING A TV PROGRAM
DEGAUSSING
TV/VCR
TV/VCR
1
Plug in the unit power cord
Plug the unit power cord into a standard
AC outlet.
NOTE:
• If any digits appear in the corner of the
screen, hit [POWER] without unplugging the power cord.
2
Turn on the unit
This television has a degaussing circuit that will clear
up color errors on the TV screen that are caused by
any excess magnetism which happens to get too close
to the TV. This circuit is designed to operate once
when the set is first plugged in. If minor color
errors are seen in some locations on the screen,
please unplug the TV for approximately 30 minutes. When the TV is plugged back in, the degaussing circuit will operate once to clear them up. Repeat
this procedure any time the TV screen is accidentally
magnetized or when the TV is moved or relocated.
Hit [POWER] to turn on the unit.
3
PICTURE CONTROL
TV/VCR
Select the channel number
Press [CH. K / L] or the Number buttons to select
your desired channel number.
Note for using the Number buttons:
¡You must precede single-digit channel numbers
with a zero (for example: 02, 03, 04 and so on).
¡When selecting cable channels which are higher
than 99, hit [+100] first, then press the last two
digits. (Example: to select channel 125, first hit
[+100] then hit [2] and [5].)
4
The unit’s picture controls – BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a more natural looking image.
Make sure ...
• The unit must be turned on.
1
Adjust sound
Call up the menu
Hit [PICTURE].
Press [VOL. X / Y] to adjust the
volume.
2
Hit [MUTE] to instantly mute the
C C C C CC
sound.
Hit it again to restore the previous sound level.
VOLUME 20
CCCCCCCCCC
NOTE:
• If you press [CH. K / L] in the DVD mode, you
can change the TV channels. Even if you turn off
the unit in the DVD mode, when you turn it on
again, it will go into the TV/VCR mode.
TO WATCH CABLE OR SATELLITE
CHANNEL
Select item you want to adjust
Press [K / L] until desired control is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
BRIGHT
–PPPPPPPCPPPPPPP+
3
Adjust the setting
Press [s / B] to adjust to your desired level within 5
seconds.
TO WATCH EXTERNAL INPUT
COLOR
s
to decrease
brightness
to decrease
contrast
to pale
• When an external equipment is connected to the
TINT
SHARPNESS
to purple
to soft
• If the unit is connected to a cable box or satellite
BRIGHT
box, press [CH. K / L] to select CH3 or CH4
according to the output channel setting of the
device, and select desired channel on that device.
front AUDIO/VIDEO input jacks, press
[SELECT] or [CH. K / L] repeatedly until
“AUX” appears on the screen.
CONTRAST
B
to increase
brightness
to increase
contrast
to brilliant
to green
to clear
• Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
- 15 -
EN
• Multiplex signal reception displaying picture
SLEEP TIMER
TV/VCR
•
The Sleep Timer function turns off the unit without
using [POWER] after a desired period of time.
NOTE:
• This function does not work during the recording mode.
1
ghosts or airplane flutter.
• Playback of poorly recorded or worn VCR tapes.
If the unit displays a black box
on the TV screen, this means that
the unit is set to the TEXT mode.
To clear screen, select [CAPTION1], [CAPTION2] or [OFF].
Make sure ...
• The unit must be turned on.
Call up the Sleep Timer Setting
Hit [SLEEP] so that “SLEEP 0 MINUTE” appears.
1
2
Select “CAPTION”
Hit [SETUP].
Press [K / L] to point to “CAPTION”.
Set sleep time
Hit [SLEEP] repeatedly until your
desired sleep time appears.
Each additional press will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, the Sleep Timer setting will disappear automatically.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
SLEEP 120 MINUTE
2
Select your desired caption mode
Hit [ENTER] repeatedly until your
desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
TO CANCEL THE SLEEP TIMER
Hit [SLEEP] to call up the Sleep Timer Setting. Hit
[SLEEP] repeatedly until “SLEEP 0 MINUTE”
appears.
3
CLOSED CAPTION SYSTEM
TV/VCR
You can view specially labeled (cc) TV programs,
movies, news and pre-recorded tapes with either a
dialogue caption or text display.
CAPTION mode: You can watch dramas, movies and
news while captioning the dialogues and the contents
of news.
TEXT mode: You can watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is
usually used for a second language if available.
NOTES:
• Not all programs are broadcast with closed captions. Your unit is designed to provide error free
closed captions from high quality antenna, cable
and VCR signals. Conversely, poor quality signals
are likely to result in caption errors or no captions
at all. Common signal conditions which may cause
caption errors are listed below:
• Automobile ignition noise
• Electric motor brush noise
• Weak snowy reception on TV screen
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Exit the caption setting mode
Hit [SETUP] to exit the menu.
NOTE:
• Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps 1 to 2 and select [OFF] using
[ENTER]. Then hit [SETUP] to return to TV mode.
- 16 -
EN
ADDING/DELETING CHANNELS
CHANNEL SET UP
TV/VCR
Make sure ...
• The unit must be turned on.
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
1
AUTO CHANNEL PROGRAMMING
As the initial setting, this unit has memorized all
channels, including the ones not available in your
area. This feature automatically puts only available
channels into the memory.
1
Select “CHANNEL SET UP”
Hit [SETUP].
Press [K / L] to point to
“CHANNEL SET UP”, then hit
[ENTER].
2
3
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “ADD/DELETE CH”
Press [K / L] to point to
“ADD/DELETE CH”, then hit
[ENTER].
3
Begin channel scanning
Press [K / L] to point to “AUTO
CH PROGRAMMING”, then hit
[ENTER].
The tuner scans and memorizes all
the active channels in your area.
Select “CHANNEL SET UP”
Hit [SETUP].
Press [K / L] to point to “CHANNEL SET UP”, then hit [ENTER].
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
Enter the desired channel number
Press [CH. K / L] or the Number
buttons until your desired channel
number appears. (You can also
08
press [K / L] to enter it.)
• You must precede single-digit
channel numbers with a zero
(Example: CH8)
(Example: 02 ... 09).
• When selecting cable channels which are higher
than 99, hit [+100] first, then press the last two
digits. (Example: to select channel 125, first hit
[+100] then hit [2] and [5].)
ADD / DELETE
After scanning
The tuner stops on the lowest memorized channel.
NOTES:
• When “AUTO CH PROGRAMMING” is activated where there
is no TV signal input, “NO TV
SIGNALS” will appear on the
display after the completion of
channel scanning.
• The unit may recognize CATV channels to be TV
channels if reception condition is poor. In this case,
check the antenna connection and try “AUTO CH
PROGRAMMING” again when reception conditions are better.
• Channel memory programming is NOT necessary when connected to a cable box or satellite
box. Just select the channel for cable box or
satellite input (ex. CH3) on the unit, then select
your desired channel on the cable box or satellite box.
4
NO TV SIGNALS
Delete (or add) it from (or into) memory
Hit [ENTER]. The channel number changes to light
red. The channel is deleted from memory.
• To delete another channel, repeat steps 3 to 4.
• If you hit [ENTER] again, the channel is memorized again.
Added channel : Light blue
Deleted channel : Light red
5
Exit the channel setup mode
Hit [SETUP] to exit the menu.
NOTE:
• To confirm that channel(s) has been deleted or
added, press [CH. K / L].
- 17 -
EN
CLOCK SET UP
(AUTO / MANUAL)
5
TV/VCR
The unit clock must be set correctly so that VCR
timer recording is possible. It is suggested that the
clock be set manually when first setting up the unit,
then set to [ON] the auto clock setting which will
periodically correct the setting if necessary.
NOTE:
• If you cannot receive a station with time signals,
auto clock setting cannot be performed. Use manual setting only.
Select the year
Press [K / L] until your desired
year appears.
(Example: “2005”)
Then hit [B].
6
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
FRI
2005
MINUTE
–– : ––
––
Select the hour
Press [K / L] until your desired
hour appears.
(Example: “5”, “PM”)
Then hit [B].
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
FRI
2005
MINUTE
05 : ––
PM
MANUAL CLOCK SETTING
Make sure ...
• The unit must be turned on.
In the example below, the clock is to be set to:
DATE
May 6th, 2005
SETTING TIME
5:40PM
1
05 / 06
YEAR
FRI
2005
MINUTE
05 : 40
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
B MANUAL CLOCK SET
D.S.T.
PM
your cable system, select “AUTO CLOCK” and
hit [ENTER] to turn [OFF] this function before
this step.
Select the month
Press [K / L] until your desired
month appears.
(Example: May → “05”)
Then hit [B]. (Or hit [s] to go
back one step.)
8
Start the clock
Hit [SETUP].
Although seconds are not displayed,
they begin counting from 00 when
you hit [SETUP]. Use this feature
to synchronize the clock with the
correct time.
NOTE:
• When unplugging the AC cord or if there is a
power failure for more than 3 seconds, you may
have to reset the clock.
5:40 PM
[OFF]
• If there is no local PBS station in your area or on
4
– MANUAL CLOCK SET –
MONTH DAY
HOUR
Select “MANUAL CLOCK SET”
Press [K / L] to point to “MANUAL CLOCK SET”, then hit
[ENTER].
3
Select the minute
Select “SETTING CLOCK”
Hit [SETUP].
Press [K / L] to point to “SETTING CLOCK”, then hit
[ENTER].
2
7
Press [K / L] until the
desired minute appears.
(Example: “40”)
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps 1 to 2.
2)Select the item you want to change using [B] .
3)Enter correct numbers using [K / L].
4)Hit [SETUP] to start the clock.
– MANUAL CLOCK SET –
MONTH DAY
05 / ––
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
Select the day
Press [K / L] until your desired day
appears.
(Example: 6th → “06”)
Then hit [B].
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
- 18 -
EN
AUTOMATIC CLOCK SETTING
Make sure ...
• The unit must be turned on.
• Confirm the unit is receiving a RF (Radio
Frequency) signal from either an antenna or cable
system connection using the ANT. jack on the rear
of the unit.
NOTES:
• If a cable converter box is being used, make sure it
is powered on.
• You must use the remote control to perform the
clock setting procedure.
• If the unit is connected directly to a cable converter
box or satellite box, the local PBS station must be
selected on the cable box itself and the unit must be
set to the output channel of the cable converter box
or satellite box (usually channel 3 or 4), to be able
to set up or correct the clock automatically.
1
Set “AUTO CLOCK” to [ON]
Hit [ENTER] to select [ON].
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH
[ 45]
MANUAL CLOCK SET
Press [s / B] until you locate Auto
Clock Set station number.
5
D.S.T.
[OFF]
Exit the setting clock mode
Hit [SETUP] to exit the menu.
NOTE:
• Once the unit is turned off, it will periodically
check and set the correct date and time.
DAYLIGHT-SAVING TIME
TV/VCR
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
B AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
D.S.T.
3
Enter the channel number that contains the
Automatic Clock Setting Signal
Hit [RETURN] to go back to “SETTING CLOCK”
menu.
Hit [L] to select “AUTO CLOCK
CH”.
Select “SETTING CLOCK”
Hit [SETUP].
Press [K / L] to select
“SETTING CLOCK”, then hit
[ENTER] .
2
4
[OFF]
Begin “AUTO CLOCK CH SEARCH”
Hit [L] to select “AUTO CLOCK
CH SEARCH”.
Then hit [ENTER].
• The unit begins searching for the
station which contains the auto
clock set signal. The search for a
signal may take up to 20 seconds per channel.
• When the search has ended, “_ _”
appears at the lower left of the
screen.
• Write down the number(s) that
appear on the screen. They are the
auto clock station(s) in your area.
• If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 18.
– SETTING CLOCK –
AUTO CLOCK
[ON]
Select this feature and the unit’s clock automatically
will advance one hour in April, then reverse one hour
in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
• First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM will
not record.
• Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
• The unit must be turned on.
B AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
D.S.T.
[OFF]
1
Select “SETTING CLOCK”
Hit [SETUP].
Press [K / L] to point to “SETTING CLOCK”, then hit [ENTER].
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– AUTO CLOCK CH SEARCH –
08
10
13
__
NOTE:
• During AUTO CLOCK CH SEARCH, the picture
may be distorted.
2
Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press [K / L] to point to “D.S.T.”,
then hit [ENTER] until [ON]
appears.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
B D.S.T.
3
[ON]
Exit the Daylight-Saving Time mode
Hit [SETUP] to exit the menu.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps 1 to 2 and select [OFF] using
[ENTER].
- 19 -
EN
V-CHIP SET UP
TV/VCR
This feature enables parents to prevent their children
from watching inappropriate material on TV. When
you try to access a program which is blocked,
“PROTECTED PROGRAM by ...” message appears
on the TV screen.
NOTE:
• When you select a rating and set
it to [BLOCK], the higher ratings
will be blocked automatically.
The lower ratings will be available for viewing.
• When you set the lowest rating to
[VIEW], all other ratings will automatically be
available for viewing.
V-CHIP SET UP
5
Make sure ...
• The unit must be turned on.
1
Select “V-CHIP SET UP”
Hit [SETUP].
Press [K / L] to select “V-CHIP
SET UP”, then hit [ENTER].
2
Enter Access code
ACCESS CODE
Press the Number buttons to
enter the access code.
• For the first time set-up or in the
event the unit has lost power,
enter the default code of 0000.
3
- TV/VCR SETUP -
A
_ _ _ _
P 20 A Step 4
P 21 B Step 4
P 21 C Step 4
NOTE:
• The blocked sub-ratings will
appear next to the rating category
in the “TV RATING” menu.
TV RATING SET UP
6
Blocking TV programs
Press [K / L] to select a rating that
you wish to block.
Hit [ENTER] repeatedly to set it to
[BLOCK] or [VIEW].
Selection
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
B TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
)
)
)
)
)
)
)
TV–Y7
B FV
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
Rating Category Explanations
Appropriate for all children
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
Mature audience only
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Selection
Rating Category Explanations
TV-Y7
FV
Fantasy Violence
TV-PG, TV-14, TV-MA
D
Suggestive Dialog (TV-PG, TV-14 only)
L
Coarse Language
S
Sexual Situation
V
Violence
Follow steps 1 to 3 in the “V-CHIP SET UP” section above.
4
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
)
TV–PG
Select the desired item
– V-CHIP SET UP –
TV–Y
B TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
B D
L
S
V
Press [K / L] to select “TV RATING”, “MPAA RATING” or “CHANGE CODE”, then hit [ENTER].
Refer to the pages below to set up each item.
B TV RATING
MPAA RATING
CHANGE CODE
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Setting “Sub-Ratings”
When you select the ratings of TVY7, TV-PG, TV-14 or TV-MA you
will have the option of setting sub
rating categories.
Press [K / L] to select a rating with
sub-ratings you wish to block, then
hit [ENTER] twice.
Press [K / L] to select a sub-rating,
then hit [ENTER] to set it to
[BLOCK] or [VIEW].
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TV–Y
TV–Y7 (
)
B TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
NOTE:
• To change the rating, the TV must
be turned to an unprotected program. If “PROTECTED PROGRAM by ...” appears on the
screen, please change the channel
to a station that is not protected.
- 20 -
TV–Y
TV–Y7 (
)
TV–G
B TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
PROTECTED PROGRAM
by TV-Y
EN
B
MENU LANGUAGE
MPAA RATING SET UP
TV/VCR
Follow steps 1 to 3 in the “V-CHIP SET UP” section
on page 20.
4
1
Select your desired item
Press [K / L] to point to your
desired item, then hit [ENTER] to
select [BLOCK] or [VIEW].
Selection
G
PG
PG-13
R
NC-17
X
G
PG
PG–13
B R
NC–17
X
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompanying parent or adult guardian
No one under 17 admitted
Mature audience only
2
Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”
3
Exit the Language mode
Hit [SETUP] to exit the menu.
NOTES:
• This function effects only the language on the
screen menu and not the audio source.
• If for some reason the menu is in Spanish or
French, hit [SETUP], press [K / L] to point to
“IDIOMA [ESPAÑOL]” or “LANGAGE
[FRANÇAIS]”, then hit [ENTER] repeatedly to
select desired language, then hit [SETUP].
the higher ratings will be blocked automatically.
The lower ratings will be available for viewing.
When you set the lowest rating to [VIEW], all
other ratings will automatically be available for
viewing.
5
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Hit [ENTER] repeatedly to select “ENGLISH”,
“ESPAÑOL”= Spanish or “FRANÇAIS”= French.
• When you select a rating and set it to [BLOCK],
•
Select “LANGUAGE”
Hit [SETUP].
Press [K / L] to point to “LANGUAGE”.
Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
C
CHANGE ACCESS CODE
Follow steps 1 to 3 in the “V-CHIP SET UP” section on page 20.
4
Enter New code
NEW CODE
Press the Number buttons to enter
your desired access code in the
“NEW CODE” space, then enter
the same code in the “CONFIRM
CODE” space. When completed, the menu will
return to “V-CHIP SET UP”.
• Make sure you enter exactly the same new code in
the “CONFIRM CODE” space as one in the
“NEW CODE” space. If they are different, the
“NEW CODE” space is cleared for redoing.
XXXX
CONFIRM CODE
_ _ _ _
5
Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
NOTE:
• Your personal access code will be erased and will
return to the default (0000) when a power failure
occurs or when you turn off the power using a
wall switch. If you have forgotten the code, unplug
the power cord for 10 seconds to restore the access
code to 0000.
- 21 -
EN
VIDEO CASSETTE
This unit will operate with any cassette that has the
mark. For best results, we recommend the use of
high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
• Avoid moisture. Moisture condensation may occur
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the unit. The unit will
automatically turn on.
•
•
•
on the tape if it is moved from a cold place to a
warm place or vice versa. Before using a tape with
these conditions, to avoid damage of the tape and
your unit, wait until the tape has warmed to room
temperature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
Window
WRONG
CORRECT
TWO DIFFERENT TAPE SPEEDS
REMOVING A CASSETTE
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each
mode.
1)In the stop mode, hit [C A STOP/EJECT] on the
unit. The cassette will be ejected.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
Tape Speed
Type of tape
Recording/Playback Time
T60
T120
T160
SP mode
1 hour
2 hours
2-2/3 hours
SLP mode
3 hours
6 hours
8 hours
NOTE:
• You can play back a tape recorded in LP mode
(Long Play).
ERASE PREVENTION
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Plastic Tape
NOTE:
• In DVD mode, whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
you hit [B PLAY].
In TV/VCR mode, if the cassette without tab is
inserted, playback will automatically start.
- 22 -
EN
PLAYBACK
NORMAL PLAYBACK
SLOW MOTION
TV/VCR
Make sure ...
• The unit must be turned on.
1
Insert a prerecorded tape
If the erase-prevention tab has been removed, the
unit will start playback automatically.
2
To begin playback
TV/VCR
Hit [PAUSE F], then hit [D] to start the playback
in slow motion. The unit mutes the sound during
slow motion. Hit [PLAY O] to return to normal
playback.
NOTE:
• If it is left in the slow mode for more than 5 minutes, the unit will automatically go into the stop
mode.
PLAY B
Hit [PLAY O].
STILL PICTURE
TV/VCR
3
To stop playback
STOP
Hit [STOP C].
NOTES:
• Even in the DVD mode, you can start the VCR
playback if you hit [B PLAY] (of the TV/VCR
side).
• VCR playback will stop and the mode will change
to the DVD mode by pressing [SELECT],
[B PLAY] (DVD side) or [A OPEN/CLOSE].
TRACKING ADJUSTMENT
TV/VCR
• Tracking adjustment will be set automatically
•
•
•
(Digital Tracking function) when you start playback.
Noise lines (black and white streaks) may appear
on the playback picture when playing pre-recorded
tapes or tapes recorded on other VCR. If this
occurs, press [CH. K / L] until the streaks disappear.
You can reduce the noise lines by pressing
[CH. K / L] in the slow mode too. Tracking adjustment in the slow mode will not be set automatically.
To return to the Digital Auto Tracking function,
stop the tape once and start playback.
You can view a still picture on the TV screen during
playback (the still mode). Hit [PAUSE F] during
playback. Only tapes recorded in the SLP mode will
show the least amount of lines. Hit [PLAY O] to
return to playback.
NOTES:
• You can advance the picture one frame at a time by
hitting [PAUSE F] during the still mode.
• If it is left in the pause mode for more than 5 minutes, the unit will automatically switch to the stop
mode.
VERTICAL HOLD CONTROL
TV/VCR
In the pause/still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
[CH. K / L].
NOTE:
• If there are video noise lines on the screen, refer to
TRACKING ADJUSTMENT on this page.
- 23 -
EN
SPECIAL PLAYBACK
Make sure ...
• The unit must be turned on.
• Insert a prerecorded tape.
AUTO REPEAT PLAYBACK
TV/VCR
RENTAL PLAYBACK
TV/VCR
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1
Select “USER’S SET UP”
Hit [SETUP].
Press [K / L] to point to “USER’S
SET UP”, then hit [ENTER].
2
3
1
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Set “RENTAL” to [ON]
Press [K / L] to point to
“RENTAL”.
Hit [ENTER] until [ON] appears.
The unit has the auto repeat function that allows you to
repeat a tape indefinitely without hitting [PLAY O].
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
– USER’S SET UP –
B RENTAL
REPEAT PLAY
AUTO RETURN
[ON]
[OFF]
[OFF]
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “ALL” or “BLANK”
Press [K / L] to point to “REPEAT
PLAY”.
Hit [ENTER] repeatedly until your
desired selection [ALL] or
[BLANK] appears.
– USER’S SET UP –
RENTAL
B REPEAT PLAY
AUTO RETURN
[OFF]
[ALL]
[OFF]
Exit the Rental setting
Hit [SETUP] to return to the TV mode.
4
Select “USER’S SET UP”
Hit [SETUP].
Press [K / L] to point to “USER’S
SET UP”, then hit [ENTER].
3
Exit the Repeat Play setting
Hit [SETUP] to return to the TV mode.
Start playback
Hit [PLAY O] to start playback.
“RENTAL PLAY B” appears.
• Once you select the rental mode, it stays in effect
even after you turn off the unit.
TO CANCEL THE RENTAL MODE
Repeat steps 1 to 2 and select [OFF] using
[ENTER]. Hit [SETUP] to return to TV mode.
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
4
Start playback
Hit [PLAY O] to start the Repeat Play.
“REPEAT PLAY B” appears.
• Once you select the repeat play mode, it stays in
effect even after you turn off the unit.
• If the rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps 1 to 2 and select [OFF] using
[ENTER]. Hit [SETUP] to return to TV mode.
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
- 24 -
EN
SEARCH
Make sure ...
• The unit must be turned on.
• Insert a tape.
NOTE:
• Tapes recorded in the SP or LP mode will normally
display a noise bar on the TV screen and the picture may revert to Black and White.
ZERO RETURN
3
TV/VCR
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
• Zero Return WILL NOT work on a blank tape or
a blank portion of a tape.
1
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2
Reset the counter to 0:00:00
Hit [C.RESET] repeatedly.
3
4
TIME SEARCH
TV/VCR
The Time Search function makes it possible to quickly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
NOTE:
• Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
In the example below: To watch a program before/
after 2 hour 50 minutes from the present position, in
either direction.
Begin recording or playback
1
Press [RECORD] or [PLAY O].
Hit [STOP C] when recording or playback is completed.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
To activate “ZERO RETURN”
- TV/VCR SETUP -
2
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B ZERO RETURN
TIME SEARCH
INDEX SEARCH
3
TV/VCR
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
Start Picture Search
During playback, press [D] or [E] to view at a
high speed (in forward/reverse).
Enter your desired time
Press [K / L] until your desired time
appears. (Example: “2:50” stands for
2 hours 50 minutes)
If you wish to cancel the Time
Search at this point, hit [SETUP].
PICTURE SEARCH
2
Select “TIME SEARCH”
Hit [SETUP].
Press [K / L] to point to “TIME
SEARCH”, then hit [ENTER].
Hit [SETUP].
Press [K / L] to point to “ZERO
RETURN”, then hit [ENTER].
The unit will begin rewinding and
the counter will appear on the TV
screen.
The tape will automatically stop when the counter
returns to 0:00:00 (approx.).
1
Return to normal speed
Hit [PLAY O].
TIME SEARCH
2 : 50
Begin Time Search
By pressing [s / B], the unit will rewind or fast forward to the specified point.
The time counts down during the search. When the
display shows “0:00”, the tape will start playback
automatically.
TO CANCEL DURING TIME SEARCH
Press [C A STOP/EJECT] on the unit or [STOP C].
This will delete the selected time.
Change searching speed
Press [D] or [E] again to view at super high
speed (in the LP/SLP modes only).
- 25 -
EN
INDEX SEARCH
1
TV/VCR
This feature provides a method of indexing the starting point so that it can be easily returned to in either
fast forward or rewind mode.
• The index mark will be made automatically when
[RECORD] is hit. It will also be marked at the
starting point of Timer recording and OTR.
• The index mark will not be recorded if [PAUSE
F] is hit and released during recording.
• The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 minutes for SLP recording.
• In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
CURRENT PLAYBACK PROGRAM
Beginning of
the tape
Pro.1
4
Hit [SETUP].
Press [K / L] to point to “INDEX
SEARCH”, then hit [ENTER].
2
3
INDEX MARK
Pro.3
2
Pro.4
1
Pro.5
1
2
Pro.6
3
Pro.7
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
Enter your desired number
Press [K / L] until the number of
programs that you want to skip
appears.
(Example: “03” for 3 programs)
INDEX SEARCH
03
• The Index Search mode will be canceled if the procedures are not activated in 30 seconds.
3
Begin Index Search
Press [s / B]. The unit begins rewinding or fast forwarding to the beginning of desired program.
NOTE:
• Every time an index signal is skipped, the number
in the program indicator decreases by one.
End of
the tape
Pro.2
Select “INDEX SEARCH”
4
After Index Search
When the preset program is reached, the unit will
start playback automatically.
• A video cassette must be inserted in the unit for
this function to work.
• The number of Index Searches can be set up to 20.
• This function will not operate in the recording
mode.
• When you want to cancel the Index Search while
in progress, hit [STOP C].
- 26 -
EN
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
TV/VCR
TV/VCR
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.) The “–” indication will appear when the tape has
rewound further than “0:00:00” on the tape counter.
• When the end of a tape is reached during record-
•
•
- 27 -
ing, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding
finishes, the unit will eject the tape and turn itself
off.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer recording or One Touch Recording.
EN
RECORDING
Make sure ...
• The unit must be turned on.
• Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
• This unit will ONLY record and view the same channel.
• This unit cannot record the contents from the built-in DVD.
SKIPPING UNWANTED
SCENES DURING RECORDING
NORMAL RECORDING
TV/VCR
You can ONLY watch the same TV program that is
being recorded.
1
Select the channel to be recorded
Press the Number buttons or
[CH. K / L].
NOTE:
CH 10
• If the unit is connected to a cable box or satellite
TV/VCR
Hit [PAUSE F] to temporarily stop
recording.
Press [PAUSE F] or [RECORD]
to resume recording.
NOTES:
• After 5 minutes, the unit will
automatically switch to the recording mode to prevent tape damage.
• If Closed Caption mode is on, the On-Screen
Display will appear for 5 seconds, then disappear.
PAUSE
SP
box, the unit must be on CH3 or CH4, then the
channel to be recorded must be selected on the
cable box or satellite box.
2
Select the tape speed
Hit [SPEED] to select the desired
tape speed (SP/ SLP).
SP
3
Begin recording
REC
Hit [RECORD].
SP
4
Stop recording
Hit [STOP C].
- 28 -
EN
OTR (One Touch Recording)
TV/VCR
This function enables you to set a recording length
simply by hitting [REC/OTR] on the unit.
Make sure ...
• The unit must be turned on.
• Insert a cassette tape with its erase-prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTES:
• You cannot start OTR with the remote control.
• Recording starts immediately when [REC/OTR]
is hit.
• When [REC/OTR] is hit 18 times, the unit returns
to the normal recording mode.
• To stop the OTR operation, hit [C STOP] on the
unit or on the remote control.
• To show the remaining time, hit [DISPLAY] on
the remote control so that “OTR” appears on the
TV screen. (It will show up momentarily then disappear.)
• Recording stops when the display shows 0:00.
• Please note that in the SLP mode maximum
recording time, assuming the tape is started at the
beginning, is 8 hours using T-160 (or 6 hours
using T-120).
• If the tape runs out before the end time, the unit
will switch to the stop mode immediately, ejects
the tape and turns itself off.
• Even if [POWER] is hit during OTR, the unit
continues recording.
Time(s)
1 time
2 times
3 times
Display
17 times
8:00
Recording length
(normal recording)
30 minutes
60 minutes
0:30
1:00
480 minutes
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
TV/VCR
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your unit and a source (Playing) VCR using
the following diagram.
[Fig.8]
[This unit]
AY
F.FWD
STOP/EJECT
HEADPHONE VIDEO
L
AUDIO
R
[Ex: Source VCR or
camcorder]
Audio/Video
cable
(not supplied)
AUDIO
L
R
VIDEO
OUT
1
Select the channel to be recorded
Press the Number buttons or [CH. K / L].
NOTE:
• If the unit is connected to a cable box or satellite
box, the unit must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box
or satellite box.
2
Select the tape speed
Hit [SPEED] to select the desired tape speed
(SP/SLP).
3
Begin OTR
Hit [REC/OTR] on the unit as
many times as needed. The recording length will be determined by
the number of times you hit
[REC/OTR]. Each time it is hit,
the recording time will be increased
by 30 minutes up to 8 hours.
OTR (2 : 30)
SP
IN
OUT
IN
1)Insert a pre-recorded video cassette into the source
VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the unit’s cassette compartment.
3)Hit [SPEED] on remote control for the unit to
select the desired recording speed (SP/SLP).
4)Press [CHANNEL K / L] on the unit until “AUX”
appears on the screen.
5)Hit [REC/OTR] on the unit.
6)Begin playback of the tape in the source VCR or
camcorder.
NOTE:
• For best results during copying, use the front
panel controls whenever possible. The remote
control might affect the source VCR’s playback
operation.
7)To stop copying, hit [C A STOP/EJECT] on the
unit, then stop the tape on the source VCR or camcorder.
- 29 -
EN
TIMER RECORDING
AUTOMATIC TIMER
RECORDING
1
- TV/VCR SETUP -
TV/VCR
You may set the unit to start and end a recording
while you are away. You can set 8 programs to record
on specific days, daily or weekly within a 1 year
period.
In the example below, the timer is being set to record:
DATE:
July 4th, 2005
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
CH61
TAPE SPEED:
SP
Make sure ...
• If a cable box or satellite box is connected with the
unit you will be limited to record only one channel,
and the channel selector on the unit must be selected to the output channel of the boxes CH 3 or CH
4 and then the actual channel to be recorded must
be selected on the boxes.
• Clock must be set to the correct time and date
before setting the timer.
• The unit must be turned on to program it.
• Insert a cassette tape with its erase-prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
• The channel you want to record is properly set in
advance. (Refer to page 17.)
Avoid overlap of programs ...
There is a chance that a program will not be recorded, when programs overlap;
• The program with an earlier start has priority.
• Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
• When the starting time is the same, the program set
on the highest position in the program list has priority.
• The illustration below demonstrates the sequence
of recordings.
Program 1
10:00AM - 11:00AM
Program 2
9:00AM - 10:00AM
Program 3
9:30AM - 12:00PM
B TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired program position (1 to 8)
Press [K / L] to select the desired
program position, then hit [B].
3
Set the channel number
Press [K / L] until the desired
channel number appears (Example:
CH61), then hit [B].
– TIMER PROGRAMMING –
CH DATE
B -
-
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
-
-
-
-
-
-
– TIMER PROGRAMMING –
CH DATE
---B 61
-----
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
NOTE:
• If the unit is connected to a cable box or satellite
box, the unit must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box
or satellite box.
4
Select once, every day or weekly recording
For once recording :
Hit [K] until the desired date
appears. (Example: “7/04” for
July 4th)
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 7/04 MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Then hit [B].
For every day recording : To record a TV program
at the same time on the same channel every day.
(Example: Monday through Sunday)
– TIMER PROGRAMMING –
CH DATE
Hit [L] until “EVRY DAY”
appears, then hit [B].
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY DAY -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM
Select “TIMER PROGRAMMING”
Hit [SETUP].
Confirm “TIMER PROGRAMMING” is pointed by hitting [K],
then hit [ENTER].
• If you have not yet set the clock,
“MANUAL CLOCK SET” appears. If so, follow
steps 3 to 8 on page 18. Then set the timer recording.
– TIMER PROGRAMMING –
CH DATE
10:00AM
11:00AM
Hit [L] until “EVRY” and your
desired day of the week appear
together, then hit [B].
12:00PM
*Recording period is SHADED
- 30 -
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
EN
5
Set beginning hour
Press [K / L] until the desired hour
appears. (Example: “ 7, PM” for
7:30PM)
Then hit [B].
6
Set beginning minute
Press [K / L] until the desired
minute appears. (Example: “30”
for 7:30PM)
Then hit [B].
7
Set end hour
Press [K / L] until the desired hour
appears. (Example: “8, PM” for
8:50PM)
Then hit [B].
8
Set end minute
Press [K / L] until the desired
minute appears. (Example: “50”
for 8:50PM)
Then hit [B].
9
Set the tape speed
Press [K / L] until the desired tape
speed appears. (Example: “SP”)
10
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 MON
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:12PM
-:- -:- -:- -:- -
-:-:-:-:-:-:-:-:-
-
-
-
-
-
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 MON
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:-:-:-:-:-:-:-:-
-
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 MON
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:- - - -:- - - -:- - - 8:30PM- -:- - - -:- - - -:- - - -:- - - -
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - 61
7/04 MON
B
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- - - -:- -:- - - -:- -:- - - 7:30PM 8:50PM- -:- -:- - - -:- -:- - - -:- -:- - - -:- -:- - - -
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 MON
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:- - - -:- - - -:- - - 8:50PM SP
-:- - - -:- - - -:- - - -:- - - -
Finish setting the program
TIMER PROGRAM EXTENSION
To shift the time schedule of an automatic timer
recording.
1)Hit [POWER].
2)Repeat step 1 on page 30.
3)Hit [RECORD] and select the desired program
using [K / L].
4)Hit [RECORD] again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, hit [PAUSE F] on
the remote control. The recording time returns to
the original time.
NOTE:
• When you shift forward the time schedule during
recording, the recording speed will automatically
be set to the SLP mode.
5)Press [ENTER] or [RETURN] to exit the setting
menu. Then hit [SETUP] to return to original
mode.
TO CORRECT A PROGRAM
Press [ENTER] or [RETURN] to complete setting.
• To set another program, repeat steps 2 to 10.
• Hit [SETUP] to exit the menu.
11
NOTES:
• The display will not be turned on automatically at
the time the programmed recording begins. To
watch the currently recorded TV program or to
play a DVD disc, hit [POWER] and [SELECT] to
choose the TV/VCR mode or the DVD mode.
• If the tape runs out before the end time, the unit
will switch to the stop mode immediately and the
tape will be ejected.
• While setting a program; hit [s] to go back one
•
Set the timer
Hit [POWER] to set automatic timer recording. The
recording indicator lights up.
• You must turn off the unit to activate automatic
timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
• If the erase-prevention tab is removed, the cassette
will be ejected when [POWER] is hit to off.
step and enter the correct numbers using [K / L].
After setting a program;
1)Hit [POWER].
2)Repeat steps 1 to 2 on page 30.
3)Hit [B] (or hit [s] to go back one step) until the
part you want to correct begins flashing, then
make the changes using [K / L].
4)Hit [POWER] to set automatic timer recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
- 31 -
1)Hit [POWER].
2)If recording is in progress, hit [C A STOP/EJECT]
on the unit.
3)Repeat steps 1 to 2 on page 30 and select a program you want to cancel.
4)Hit [C.RESET].
5)Hit [SETUP] to return to TV mode.
EN
TO CONFIRM THE TIMER SETTING
1)Hit [POWER] so that the Recording indicator light
goes off.
2)Hit [SETUP].
3)Confirm “TIMER PROGRAMMING” is selected.
4)Hit [ENTER]. The details of programs appear on
the TV screen.
5)Hit [SETUP] to return to TV mode.
AUTO RETURN
TV/VCR
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
1
Select “USER’S SET UP”
Hit [SETUP].
Press [K / L] to point to “USER’S
SET UP”, then hit [ENTER].
2
Set “AUTO RETURN” to [ON]
Press [K / L] to point to “AUTO
RETURN”, then hit [ENTER] until
[ON] appears.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
B AUTO RETURN
[OFF]
[OFF]
[ON]
Auto Return will begin
When all the timer recordings are completed, the unit
will rewind to the beginning of the recorded program(s).
NOTE:
• If you hit [POWER] while tape is rewinding, the
Auto Return will stop.
4
Watch the recorded program
Hit [PLAY O].
TO CANCEL THE AUTO RETURN
MODE
Repeat steps 1 to 2 and select [OFF] using
[ENTER].
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
- 32 -
EN
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, hit [DISPLAY]. Each time you hit [DISPLAY], the TV screen will change as follows:
When the Closed Caption mode is OFF:
When the Closed Caption mode is ON:
• Counter mode: After 5 seconds, only the counter
• The On Screen Display disappear after 5 seconds.
• This is true even if [MUTE] or [PAUSE F] is
•
remains. To clear it, hit [DISPLAY].
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, hit
[DISPLAY].
OFF mode
Counter mode
OFF mode
Clock mode
STOP
SP
pressed while recording.
STOP
COUNT 0:12:34
Clock/Counter mode
5:40PM
CH2
STOP
5:40 PM
CH2
SP
After 5 seconds
After 5 seconds
SP
COUNT 0:12:34
5:40PM
CH2
COUNT 0:12:34
Counter
remains
Clock & Channel
remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
5A
2
3
4
5
6
7
8
9
10
11
12
13
A
B
TV Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CATV channel
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
TV Display
CATV channel
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
TV Display
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CATV channel W+10
TV Display
46
CATV channel W+25
TV Display
61
CATV channel W+40
TV Display
76
CATV channel W+55
TV Display
91
CATV channel W+65
TV Display
106
CATV channel W+80
TV Display
121
W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
47
48
49
50
51
52
53
54
55
56
57
58
59
60
W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
62
63
64
65
66
67
68
69
70
71
72
73
74
75
W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
77
78
79
W+56 W+57 W+58
92
93
94
80
81
82
83
84
85
86
A-5
A-4
A-3
A-2
A-1
W+59 W+60 W+61 W+62 W+63 W+64
95
96
97
98
99
100
101
87
102
88
103
89
104
90
105
W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
107
108
109
110
111
112
113
114
115
116
117
118
119
120
W+81 W+82 W+83 W+84
122
123
124
125
- 33 -
EN
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
Playable
discs
DVD-Video
Mark (logo)
Region code
Recorded
signals
Disc size
Digital video
(MPEG2)
12 cm
or
8cm
Digital audio
12 cm
or
8cm
Disc types
or
* 1,2,3,10
DVD-RW
DVD-R
-
Example
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
* 1,3,4,5,6
8,9
DVD+RW
DVD+R
-
* 1,3,4,5,7,8,9
Audio CD
* 3,5
CD-RW
CD-R
-
Audio CD
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
* 3,4,5,8,9
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot
be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Scratched or stained discs may not be played back.
*4: Some discs cannot be played back because of incompatible recording conditions, characteristics of the
recorder or special properties of discs.
*5: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not
play them back. Even if they are played back, the sound or video quality will be compromised.
*6: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with
the DVD recorder. Refer to the manual accompanying the DVD recorder.
*7: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be
played back at all or normally (the picture or sound may not be smooth, etc.).
*8: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not
play back properly.
*9: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.
*10: The number inside the symbol refers to a region of the world and a disc encoded in a specific region format can only be played back on unit with the same region code.
:This label indicates playback compatibility with DVD-RW discs recorded in VR mode (Video Recording Format).
NOTE:
• This player cannot play the DVD-RW that supports CPRM (Contents Protection for Recordable Media).
• This player cannot play the DVD-R discs recorded in VR mode (Video Recording Format).
UNPLAYABLE DISCS
¡NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3
¡On the following disc, the sound MAY NOT be heard.
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
¡Any other discs without compatibility indications
– 34 –
EN
PLAYING A DISC
BASIC PLAYBACK
DVD-V
GENERAL FEATURES
CD
DVD-V
Getting started
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1 Hit [POWER].
¡The power will turn on.
2 Hit [A OPEN/CLOSE] to open disc loading
tray.
3 Place the chosen disc in the tray, with the
label facing up.
DVD may contain menus to navigate the disc and
access special features. Press the appropriate
Number buttons or [K / L / s / B] to highlight your
selection in the DVD main menu and hit [ENTER] to
confirm.
NOTES:
¡Select DVD mode by hitting [SELECT], then operate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
DISC MENU
DVD-V
4 Hit [PLAY O].
¡The tray will close automatically and playback will
then start from the first chapter or track of the disc.
1 Hit [DISC MENU].
¡The DVD main menu will appear.
¡If the feature is not available,
symbol may
appear on the TV screen.
¡If disc menu is available on the disc, audio language,
subtitle options, chapters for the title and other
options will appear for selection.
¡Closing the disc tray manually or by hitting
[A OPEN/CLOSE] also starts playback.
¡If the playback does not start automatically, hit
2 Press [K / L / s / B] to select an item and hit
[PLAY O].
¡When you playback a DVD which features a title
menu, it may appear on the screen. In this case, refer
to “TITLE MENU” on this page.
[ENTER] to confirm selection.
TITLE MENU
DVD-V
5 Hit [STOP C] to stop playback.
NOTES:
¡When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and
then the TV picture and sound appears in about 4 seconds. Similarly, when [POWER] is hit to turn off in
the DVD mode, this mode shuts down first and then
the unit is turned off.
¡A “prohibited icon” may appear at
the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc.
¡With DVDs that use titles for playback program signals, playback may start from the second title or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a malfunction.
1 Hit [TITLE].
¡The title menu will appear.
¡If the feature is not available,
symbol may
appear on the TV screen.
2 Press [K / L / s / B] to select an item, and
hit [ENTER] to confirm selection.
CALLING UP A MENU SCREEN
DURING PLAYBACK
¡Hit [DISC MENU] to call up the DVD menu.
¡Hit [TITLE] to call up the title menu.
NOTE:
¡Contents of menu and corresponding menu operations may vary between discs. Refer to the manual
accompanying the disc for details.
– 35 –
EN
SLOW FORWARD /
SLOW REVERSE
RESUME
DVD-V
CD
DVD-V
1 During playback, hit [STOP C].
¡Resume message will appear on the TV screen.
1 During playback, hit [PAUSE F].
2 Press and hold [g] or [h ] for a few
2 Hit [PLAY O], playback will resume from the
seconds.
point at which playback was stopped.
¡To cancel resume, hit [STOP C] twice.
¡The resume information stays on even when the
¡“
1” or “
1” appears on the screen.
3 To select another speed, repeat step 2 until
power is turned off.
your required speed number appears on the
screen.
PAUSE
¡Slow forward or reverse speed varies with the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
DVD-V
CD
¡When you press buttons on the main unit, use
[SEARCH h / g].
1 During playback, hit [PAUSE F].
4 To return to normal playback, hit [PLAY O].
¡Playback will pause and sound will be muted.
2 To continue playback, hit [PLAY O].
ZOOM
STEP BY STEP PLAYBACK
DVD-V
DVD-V
1 During playback, hit [PAUSE F].
¡Playback will pause and sound will be muted.
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1 Hit [ZOOM] during playback.
¡Playback will continue.
2 The disc goes forward by one frame each
2 Hit [ZOOM] repeatedly to select the required
time [PAUSE F] is hit.
zoom factor: ZOOM1, ZOOM2, ZOOM3 or
OFF.
3 To exit step by step playback, hit [PLAY O].
3 Press [K / L / s / B] to move the zoomed
FAST FORWARD /
FAST REVERSE
DVD-V
picture across the screen.
4 To exit zoom mode, hit [ZOOM] to OFF.
CD
1 During playback, press and hold [g] or
[h ] for a few seconds.
¡“ g 1” or “h 1” appears on the screen.
2 To select another speed, repeat step 1 until
your required speed number appears on the
screen.
¡For DVDs, fast forward/reverse search speed is dif-
NOTES:
¡Zooming function does not work while disc menu is
shown.
¡Zooming function is not available on some discs.
¡It may take several seconds to slide the zoomed picture.
¡The picture may be distorted if you operate other
functions repeatedly (ex. [PAUSE F] or [h], etc.)
in the zoom mode.
ferent depending on the disc. Approximate speed is
1(×2), 2(×8), 3(×20), 4(×50) and 5(×100).
¡For Audio CDs approximate speed is 1(×2), 2(×8)
and 3(×30).
¡When you press buttons on the main unit, use
[SEARCH h / g].
3 To return to normal playback, hit [PLAY O].
– 36 –
EN
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
DVD-V
There are three ways to begin playback on an Audio
CD at a specific track.
CD
1 During playback, hit [SEARCH MODE] three
times (CD: twice) to display the Time Search
on the TV screen.
Using the Number buttons
2 Within 30 seconds, enter a desired disc
1 Press the Number buttons to enter the
desired track number.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, hit [3]).
time using the Number buttons.
¡Playback will start at the specified time.
¡Hit [CLEAR] to erase the incorrect input.
¡When there is no need to enter a number, “0”
appears automatically. For example, “ 0 : 0 - : - -”
appears in the Time Search display if the total time
of the track or title is less than 10 minutes.
¡To play track 26, hit [+10], [2], [6].
Using [SEARCH MODE]
1 Hit [SEARCH MODE].
¡The track search display appears.
MARKER SETUP SCREEN
DVD-V
2 Within 30 seconds, select the desired track
number using the Number buttons.
¡For single digits hit [0] first, if the total track of the
CD
Use markers to memorize your favorite places on a
disc.
disc is 10 tracks or more.
1 Hit [SEARCH MODE] four times (CD: three
¡Playback will start at the selected track.
times) during playback.
¡The display screen and Markers will appear on the
Using [H / G ]
During playback, hit [G] to move the next track. Hit
it repeatedly to skip subsequent tracks. Hit [H] to go
back to beginning of the current track. Hit it repeatedly to go to the previous tracks.
¡If [H / G] is pressed while the playback is
paused, the playback will be paused again after skipping to the next track.
NOTE:
¡[H / G] are not operative when playback is
stopped.
TV screen.
2 Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,
or 10 and ensure that “- - - - : - - : - -”
appears in the display.
3 When you reach the desired point, hit
[ENTER].
¡The Title or Track and elapsed playing time will
appear in the TV screen.
4 To return to the Marker later, hit [SEARCH
TITLE / CHAPTER SEARCH
MODE] four times (CD: three times) during
playback and press [s / B] to choose the
desired marker, then hit [ENTER].
DVD-V
1 Hit [SEARCH MODE] once for the Chapter
search, twice for the Title search during
playback.
_/2
2 Enter the desired chapter/title number using
the Number buttons.
¡Playback will start at the selected chapter or title.
¡Hit [CLEAR] to erase the incorrect input.
¡For single digits hit [0] first, if the total number of
NOTES:
¡Operations which erase all Markers:
– Opening the disc tray.
– Turning off the power.
– Hitting [SELECT].
– Selecting “AC” at step 2 and hitting [ENTER].
¡To clear a marker:
– Press [s / B] to select a cursor on to the marker
number and hit [CLEAR].
¡You can mark up to 10 points.
chapter or title of the disc is 10 or more.
– 37 –
5 Press [SEARCH MODE] or [RETURN] to
exit.
EN
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
REPEAT is available only during playback.
CD
REPEAT TITLE / CHAPTER
DVD-V
To activate the repeat function, hit [REPEAT]
during playback.
¡The repeat mode changes as described below every
time you hit the button.
CHAPTER
TITLE
(current chapter repeat) (current title repeat)
OFF
(repeat off)
You may determine the order in which tracks will play.
1 In the stop mode, hit [MODE].
¡The “PROGRAM” screen will appear.
2 Press [▲ / ▼] to select a track, then hit
[ENTER].
¡Hit [CLEAR] to erase the
most recently entered track.
1/4
3:30
5:10
4:20
3:00
3:20
4:10
2:50
2/3
3 Repeat step 2 until you have selected all the
tracks you want to play in the program.
4 Hit [PLAY O] to play the programmed tracks.
REPEAT TRACK
CD
To activate the repeat function, hit [REPEAT]
during playback.
¡The repeat mode changes as described below every
time you hit the button.
ALL
(entire disc repeat)
OFF
(repeat off)
NOTES:
¡Repeat setting will be cleared when moving to other
track.
¡Repeat playback does not function during A-B
repeat playback.
NOTES:
¡While the program is being played back, hitting
[STOP C] works as follows.
¡Hit [STOP C] once and then [PLAY O] again,
playback will restart from the point where
[STOP C] was hit. (Program continued)
¡Hit [STOP C] twice and then [PLAY O] again,
playback will restart from the track in the usual way.
(Program canceled)
¡Up to 99 tracks can be entered.
¡To erase all tracks in the program at once, select
“ALL CLEAR” at the bottom of the list at step 2.
¡If you like to repeat the current track in the program,
hit [REPEAT] several times until “
TRACK”
appears during playback. If you like to repeat the
entire program hit [REPEAT] several times until
“ ALL” appears during playback.
A-B REPEAT
DVD-V
RANDOM PLAYBACK
CD
CD
1 Hit [A-B] at your chosen starting point.
¡“
1
5
10
11
12
17
22
displayed at once on a screen,
“G” appears to go to the next
page and “ H” appears to go
back to the previous page.
NOTES:
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
TRACK
(current track repeat)
TOTAL 1:03:30
¡If the entire Program cannot be
This function shuffles the playing order of tracks
instead of playback in the sequence.
A-” appears briefly on the TV screen.
2 Hit [A-B] again at your chosen end point.
¡“
A-B” appears briefly on the TV screen, and the
repeat sequence begins.
1 In the stop mode, hit [MODE] twice.
¡“RANDOM” screen appears.
RANDOM
CD-DA
3 To exit the sequence, hit [A-B].
TOTAL 0:45:55
RANDOM PROGRAM
- - no indication - -
NOTES:
¡The A-B repeat section can only be set within the current title (for DVDs) or current track (for Audio CDs).
¡A-B repeat is not available with some scenes in DVD.
¡To cancel the A point which was set, hit [CLEAR].
¡A-B repeat playback does not function during title,
chapter, track or all repeat playback.
PLAY
2 Hit [PLAY O] to start random playback.
NOTE:
¡If you like to repeat the current track in the random
selection, hit [REPEAT] several times until “
TRACK” appears during playback. If you like to
repeat the entire random selection hit [REPEAT] several times until “ ALL” appears during playback.
– 38 –
EN
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
AUDIO LANGUAGE
DVD-V
DVD-V
The unit allows you to select a language for subtitles
during DVD disc (if available) playback.
The unit allows you to select a language during DVD
disc (if multi languages are available) playback.
1 Hit [AUDIO] during playback.
1 Hit [SUBTITLE] during playback.
¡The subtitle language will
appear on the display bar at
the top of the TV screen.
1.ENG Dolby D 3/2.1ch 48k/3
1.ENG/6
2 Hit [AUDIO] repeatedly to select your
2 Hit [SUBTITLE] repeatedly to select your
desired language.
desired subtitle language.
3 To turn off subtitles, hit [SUBTITLE] repeatedly until “OFF” appears.
NOTES:
¡Hitting [SUBTITLE] may not work on some DVDs
with multiple subtitle languages. In this case, set it
on the disc menu. (Operation varies between discs.
Refer to the manual of the disc.)
¡If the desired language is not shown after hitting
[SUBTITLE] several times, the disc does not have
subtitles in that language.
¡When “NOT AVAILABLE”
appears on the TV screen, it
means no subtitle is recorded
on the scene.
¡If you choose a language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, “---” will be displayed instead.
(Refer to page 42.)
NOTE:
¡Hitting [AUDIO] may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
STEREO SOUND MODE
CD
1 Hit [AUDIO] repeatedly during playback to
select between “STEREO”, “L-ch” or “R-ch”.
NOT AVAILABLE
STEREO
¡STEREO - both right and left channels are active (stereo)
– 39 –
L-ch - only left channel is active
R-ch - only right channel is active
EN
CAMERA ANGLE
VIRTUAL SURROUND
DVD-V
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
the camera angle when the “
” icon appears on the
screen.
DVD-V
CD
You can enjoy surround-sound effect over two speakers on this unit.
1 Hit [MODE] twice (CD: once) during playback.
1 Hit [ANGLE] during playback.
OFF
¡The selected angle will be displayed on the display
bar at the top of the screen.
2 Hit [ENTER] to set it “1” (Natural effect), “2”
1/8
(Emphasized effect) or “OFF”.
¡If the “ANGLE ICON” setting is “OFF” in the
“OTHERS” menu, the “
(Refer to page 44.)
3 Hit [RETURN] to exit.
” icon will not appear.
NOTE: (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
2 Hit [ANGLE] repeatedly to select your
desired angle.
BLACK LEVEL SETTING
DVD-V
Adjust the Black Level Settings to make the black
parts of the picture brighter.
1 Hit [MODE] during playback.
OFF
2 Hit [ENTER] to switch “ON/OFF”.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
(Initial setting)
3 Press [MODE] twice or [RETURN] to exit.
NOTE:
¡The setting will be saved even if the unit is turned
off.
– 40 –
EN
THE ON-SCREEN INFORMATION
DVD-V
CD
You can check the information about the current disc by hitting [DISPLAY].
For DVD-Vs
For Audio CDs
1 Hit [DISPLAY] during playback to show current Chapter.
¡The elapsed and remaining
9/49
1 Hit [DISPLAY] during playback to show the
current Track.
¡The elapsed and remaining playing time of the cur-
0:00:00 -0:03:30
playing time of the current
chapter will be displayed.
rent track will be displayed.
2 Hit [DISPLAY] again to show current Title.
¡The elapsed and remaining
playing time of the current title
will be displayed.
3 Hit [DISPLAY] again.
¡The bit rate and the current
1/3
Track.
¡The elapsed and remaining playing time of the total
track will be displayed.
4/12 0:13:45 - 0:45:40
T
L1
repeat setting will be displayed.
¡If you are playing a dual layered disc, the layer number will also be displayed
(L0: Layer 0 is playing. L1: Layer 1 is playing).
4 Hit [DISPLAY] again to exit.
T
2 Hit [DISPLAY] again to show current Total
0:00:00 - 1:23:45
T
4/12 0:03:21 - 0:02:15
3 Hit [DISPLAY] again to exit.
NOTE:
¡When you are playing a disc in
PROGRAM or RANDOM mode, “
(or RANDOM) will be displayed at step 2.
– 41 –
PROGRAM”
PROGRAM
B
EN
CHANGING THE DVD SET UP ITEMS
Language
CUSTOM MENU
DVD-V
You can change the DVD player’s settings.
1 Hit [SETUP] twice in the stop mode so that
the DVD SETUP menu appears.
¡Hit [L] to select “CUSTOM”
SETUP
then hit [ENTER].
QUICK
CUSTOM
INITIALIZE
NOTE:
¡If the menu does not appear, hit [PLAY O] first,
then hit [STOP C]. Make sure the disc is in the stop
mode, then slowly hit [SETUP] twice.
2 Select the desired item.
¡Press [K / L] to select the desired item then hit
[ENTER] to confirm.
Refer to the pages below to set up each item.
P 42 A
P 43 B
P 43 C
P 44 D
P 44 E
LANGUAGE SETTING
SETUP
Step 3
Step 3
Step 3
Step 3
Step 3
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
A
Follow steps 1 to 2 in the “CUSTOM MENU” section
above.
3 Press [K / L] to select the desired item then
hit [ENTER].
AUDIO:
Sets the audio language.
SUBTITLE:
Sets the subtitle language.
DISC MENU:
Sets the language for DVD
menu.
SETUP
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
ORIGINAL
OFF
ENGLISH
4 Press [K / L] to select a setting then hit
[ENTER].
¡If “OTHER” is selected on
the “AUDIO”, “SUBTITLE”
or “DISC MENU” screen,
press four-digit number to
enter the code for the desired
language. (Refer to the language code list.)
¡Only the languages supported by the disc can be selected.
SETUP
LANGUAGE
AUDIO
ORIGINAL
ENGLISH
FRENCH
SETUP
LANGUAGE
SUBTITLE
OFF
ENGLISH
FRENCH
SETUP
Code Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
LANGUAGE
DISC MENU
ENGLISH
FRENCH
SPANISH
5 Hit [SETUP] to exit the menu.
NOTES:
¡Language Setting for Audio and Subtitle are not
valid for some discs due to default setting of the
disc. In this case, set them by hitting [AUDIO] and
[SUBTITLE]. (Refer to page 39.)
¡If you select a language that is not supported by the
disc, subtitle will automatically be set OFF and the
first item of the audio languages will be automatically set.
Code
L-N
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
If you choose a language that has a 3 letter language
code, the code will be displayed every time you change
the AUDIO or SUBTITLE language setting above. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
– 42 –
EN
B
C
DISPLAY SETTING
Choose the appropriate Audio settings for your equipment as it only affects during the playback of DVD
discs.
Follow steps 1 to 2 in the “CUSTOM MENU” section on page 42.
3 Press [K / L] to select the below items then
hit [ENTER].
Follow steps 1 to 2 in the “CUSTOM MENU” section on page 42.
TV MODE: QUICK
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
¡4:3 LETTER BOX (default):
To show black bars on top
and bottom of the screen.
SETUP
TV MODE
STILL MODE
AUDIO SETTINGS
3 Press [K / L] to select the below items then
hit [ENTER].
DRC (Dynamic Range
Control):
¡To compress the range of soft
to loud sound.
¡The default setting is “ON”.
DISPLAY
4:3 LETTER BOX
AUTO
¡4:3 PAN & SCAN: To show
a full height picture with both sides trimmed.
SETUP
SETUP
DISPLAY
ON
ON
BITSTREAM
DOWN SAMPLING:
¡ON : Output in 48 kHz.
DRC
ON
DOWN SAMPLING
ON
(default)
DOLBY DIGITAL
BITSTREAM
¡OFF : Output the original
sound.
When playing disc with copyright Protection
¡If you select “OFF”, copyright protection will be
activated and sound will be down sampled at 48kHz.
SETUP
STILL MODE:
This function allows you to adjust picture resolution
and quality in the still mode.
¡AUTO (default):
Automatically select the best
TV MODE
4:3 LETTER BOX
AUTO
STILL MODE
resolution setting (FRAME
or FIELD) based on the data
characteristics of the pictures.
¡FIELD: Select “FIELD” when the pictures are still
unstable even if “AUTO” is selected.
FIELD stabilizes the pictures, although the picture
quality may become coarse due to the limited
amount of data.
¡FRAME: Select “FRAME” to display relatively
motionless pictures in higher resolution.
FRAME improves the picture quality, although it
may unstabilizethe pictures due to simultaneous
output of two field data.
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
AUDIO
DOLBY DIGITAL: QUICK
DRC
ON
Set to “BITSTREAM” when
DOWN SAMPLING
ON
DOLBY DIGITAL
BITSTREAM
the unit is connected to a
Dolby Digital Decoder.
¡BITSTREAM: Output a Dolby Digital signal
(default)
SETUP
AUDIO
¡PCM: Convert the Dolby Digital to PCM
(2 channel stereo)
4 Hit [SETUP] to exit the menu.
4 Hit [SETUP] to exit the menu.
QUICK MENU
¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the
QUICK menu, select “QUICK” instead of “CUSTOM” at step 1 on page 42.
LANGUAGE SETTING FOR THE ON-SCREEN MENUS
¡You can access the TV/VCR SETUP menu by hitting [SETUP] from the DVD mode. Refer to
“MENU LANGUAGE” on page 21 to change the language for the on-screen menus.
– 43 –
EN
D
PARENTAL CONTROL
IF YOU FORGET THE PASSWORD
Parental Control limits the disc viewing that exceed
your setting (with a password or playback will stop).
This feature allows you to prevent discs with alternative scenes from being played by your children.
1 Hit the Number buttons [4], [7], [3], [7] at
step 3 . Then enter your new password.
¡Password will be cleared and parental level will be
set to “ALL”.
PARENTAL LEVEL
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.
Follow steps 1 to 2 in the “CUSTOM MENU” section on page 42.
2 Proceed with steps 4 to 6 again.
E
Follow steps 1 to 2 in the “CUSTOM MENU” section on page 42.
3 Press [K / L] to select the below items,
3 Enter your four-digit password then hit
[ENTER].
SETUP
OTHER SETTINGS
then hit [ENTER].
PARENTAL
PASSWORD
4 Press [K / L] to select “PARENTAL LEVEL”
then hit [ENTER].
SETUP
PARENTAL
PARENTAL LEVEL
ALL
PASSWORD CHANGE
5 Press [K / L] to select the desired level
then hit [ENTER].
SETUP
SETUP
OTHERS
ANGLE ICON
AUTO POWER OFF
Enter current password.
PARENTAL
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
ON
ON
ANGLE ICON:
¡Hit [ENTER] repeatedly to turn Angle icon “ON” or
“OFF”.
¡The default setting is “ON”.
AUTO POWER OFF:
¡Hit [ENTER] repeatedly to turn Auto Power off
“ON” or “OFF”.
¡The default setting is “ON” and the screen saver program starts when there is no input from the unit for 5
minutes in the stop mode. After the screen saver program is activated for 15 minutes, the power is automatically turned off.
5 Hit [SETUP] to exit the menu.
6 Hit [SETUP] to exit the menu.
NOTES:
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the password. (in the event you forget the password, see below)
¡To change the password, press [K / L] to select
“PASSWORD CHANGE” at step 4 then hit
[ENTER]. Enter the four-digit password, then hit
[ENTER].
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
INITIALIZE
DVD-V
This allows you to return all selections of SETUP
(except for “PARENTAL” and menu language) to
their default settings.
1 Hit [SETUP] twice in the stop mode so that
the “INITIALIZE” menu appears.
2 Press [K / L] to select “INITIALIZE” then hit
[ENTER].
SETUP
QUICK
CUSTOM
INITIALIZE
CONTROL LEVELS
¡ALL
3 Press [K / L] to select “YES” then hit
All parental lock is cancelled.
[ENTER] twice.
¡Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
All the settings (except for
“PARENTAL” and menu
language) will be cleared.
¡To cancel the initialization,
select “NO”.
SETUP
INITIALIZE
Initialize?
NO
YES
4 Hit [SETUP] to exit the menu.
¡Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
– 44 –
EN
TROUBLESHOOTING GUIDE
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, consulting the following checklist.
PROBLEM
No power
No operation by infrared remote
control
CORRECTIVE ACTION
Make
sure
the
power
plug is connected to an AC outlet.
•
Make
sure
the
power
is turned on.
•
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote control.
• You have to be within 23 feet of the unit.
• Check if the correct mode is selected. If not switch the mode by
hitting [SELECT], whichever you need.
TV/VCR Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
No picture or sound
CORRECTIVE ACTION
• Make sure the AC cord is connected to an AC outlet.
• Check antenna connection.
• Hit [SELECT] to select TV mode.
Then try other TV feature.
No picture or poor picture on the
unit
No sound or poor sound
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
• Let the unit program its tuner memory.
• Adjust direction or replace antenna.
• Adjust picture controls.
• Check for broken pin of the antenna cable.
• Adjust volume control on remote control or main unit.
• Hit [MUTE] to restore sound.
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Try a new channel, if OK, then possible station trouble.
• If outside antenna is being used, check for broken wire.
• Try a new channel, if OK, then possible station trouble.
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to jack on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust “COLOR” control.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to jack on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to jack on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust “CONTRAST” & “BRIGHT” control.
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to jack on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Adjust “CONTRAST” & “BRIGHT” control.
– 45 –
EN
PROBLEM
Picture OK, Sound Poor
Timer recording is not possible
Cannot go into the recording mode
Playback picture is partially noisy
No picture but the audio is OK in
playback
No operation by infrared Remote
Control
Video or color fades in and out
when making a copy of a video tape
Different color marks on screen
CORRECTIVE ACTION
• Try a new channel, if OK, then possible station trouble.
• Check for local interference.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the unit’s clock is set correctly.
• Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
• Adjust tracking control for a better picture using [CHANNEL K / L]
• on the unit.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 48.
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
• Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the unit away from the appliances,
the unit can repair itself automatically. If you want to repair immediately, unplug the power cord, then plug it in again 30 minutes later or
so. This automatically resets the unit.
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
Misspelling in captions
• Error committed by the closed captioning production company.
• Possible in a live broadcast. Not in case of a prerecorded program.
Text is not shown in its entirety or
• A few seconds of delay is common for live broadcast.
a delay occurs from what is being
• Display capacity may not exceed 220 words per minute. If a dialogue
said.
• exceeds that rate, selective editing is used to insure that the captions
• remain up-to-date with the current TV screen dialogue.
Captions scrambled with white
• Caused by interferences of building, power lines, thunderstorms, etc.
boxes
No captions in a program which
• The broadcast may use a time compression process to speed up the
must contain closed caption
• program. The decoder cannot read the compressed information and
• captions will be lost.
No captions in a prerecorded
• Possibility of a illegal copy or an erroneous copying process
videotape which indicated closed
• accidentally performed by the fabricator.
captions included.
Black box in the TV screen
• You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or
• Caption “OFF”.
– 46 –
EN
DVD Mode
PROBLEM
CORRECTIVE ACTION
No picture
• Insert a correct video disc that plays on this unit.
• Hit [SELECT] to select DVD mode, then try other DVD feature.
• Insert the disc.
Disc cannot be played
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This unit does not support DTS audio. This is not a malfunction.
No DTS audio is output
• There are some cases where pictures may be slightly distorted, which
Distorted picture
are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
• The selected language is not available for audio or subtitles on the
does not match the set up
DVD. (This is not a malfunction.)
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera
angles. (This is not a malfunction.)
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected
changed
language. (This is not a malfunction.)
“Prohibited icon” appears on the
• That operation is prohibited by the unit or the disc.
screen, prohibiting an operation
(This is not a malfunction.)
CD sound dropout
• Scratched disc. Replace the disc with an unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
– 47 –
EN
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
•
the unit with a soft cloth immersed in lukewarm
water and wrung dry.
Never use a solvent or alcohol. Do not spray insecticide liquid near the unit. Such chemicals may
cause damage and discoloration to the exposed surfaces.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line mentioned on the
front page, to locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
AUTO HEAD CLEANING
SERVICING
• Automatically cleans video heads as you insert or
•
remove a cassette, so you can see a clearer picture.
Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your unit may need to be
cleaned.
• Should your unit become inoperative, do not try to
correct the problem by yourself. There are no userserviceable parts inside. Turn off, unplug the power
cord and please call our help line mentioned on
the front page, to locate an Authorized Service
Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
• If the unit still does not perform properly when it is operated, while referring to the relevant sections and to
“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup
unit.
DISC HANDLING
• Handle the discs so that fingerprints and dust do
• To clean-off, use a soft cloth.
• Do not use a hard cloth since this will mar the disc.
• Wipe the disc in a straight line from center to edge.
• Never wipe with a circular motion.
• Do not use detergent or abrasive cleaning agents.
not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it
is not used.
– 48 –
EN
SPECIFICATIONS
GENERAL SPECIFICATIONS
TV/VCR
CRT
19 inch in-line gun,
90˚ deflection tube
Television system :
NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Rotary four-head
Tape width :
1/2 inch
Tape speed
SP :
33.40mm/sec.
LP :
16.67mm/sec.
SLP :
11.12mm/sec.
Tuner channel
TV VHF Low :
#2~#6
TV VHF High :
#7~#13
TV UHF :
#14~#69
CATV
VHF :
5A
MID band :
A5~A1, A~I
SUPER band :
J~W
HYPER band :
W+1~W+84
DVD
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input:
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output:
Remote control:
Operating
temperature:
Power requirements:
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
1/8” stereo (3.5 mm)
One pin jack,
500m Vpp (75 ohm)
Digital encoded
infrared light system
5˚C to 40˚C
(41˚F~104˚F)
AC 120V, 60Hz
90W
19"
H:19-11/16" (500mm)
W:21-7/8" (556mm)
D:18-3/4" (477mm)
45.2 lbs. (20.5kg)
Product type:
DVD Player
Discs:
DVD video, Audio CD
Output signal format: NTSC color
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will be English.
– 49 –
EN
INDICE
■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 50
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 51
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 51
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 51
CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 52
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
EQUIPADO CON TOMAS DE ENTRADA DIGITAL.
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
SECCIÓN DE TV/VCR
■ FUNCIONES Y AJUSTES DE TV . . . . . . . . . . . . . . . . . 53
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 53
IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
■ GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . . . . . 54
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
CONTROLES DE
OPERACIÓN Y FUNCIONES
• Consulte la figura 1 de la página 9 para el
panel frontal de la unidad
• Consulte la figura 2 de la página 9 para el
mando a distancia
• Consulte la figura 3 de la página 10 para la
vista posterior
1. Botón POWER
Presione para encender y apagar la unidad.
2. Botones VOLUME (VOL.) K / L
Presione para controlar el nivel de volumen del DVD y
el televisor.
3. Botones SKIP H / G (para DVD)
Presione una vez para omitir capítulos o pistas y
desplazarse a un punto específico.
Botones SEARCH E / D (para DVD)
Mantenga el botón presionado para cambiar la
velocidad de reproducción en avance o retroceso.
4. Botón B PLAY
Inicia la reproducción del contenido del disco o cinta.
5. Botón C STOP
(Panel frontal) Detiene la operación del disco.
(Mando a distancia) Detiene la operación del disco o el
casete.
6. Botón A OPEN/CLOSE
Presione para insertar un disco en la bandeja o retirarlo
de ella.
7. Bandeja de carga del disco
8. Indicador DVD
Se ilumina durante el modo DVD.
9. Botón SELECT
Presione para cambiar al modo TV/VCR, modo de
entrada externa o modo de DVD. El modo
seleccionado (TV/VCR o DVD) se visualiza en el
indicador del panel delantero.
10. Indicador TV/VCR
Se ilumina durante el modo TV/VCR.
11. Botones CHANNEL (CH.) K / L
Utilice para seleccionar canales memorizados.
12. Indicador de grabación
Parpadea durante la grabación. Se ilumina durante el
modo de espera de grabación controlada por
temporizador.
13. Botón REC/OTR (Panel frontal)
Presione para empezar la grabación manual. Presione
repetidamente para empezar la grabación instantánea (OTR).
Botón RECORD (Mando a distancia)
Presione para empezar la grabación manual.
14. Botón E REW (para TV/VCR)
Presione para rebobinar la cinta o para ver la imagen
rápidamente en dirección de retroceso durante el modo
de reproducción. (Búsqueda en dirección de retroceso)
15. Botón F.FWD D (para TV/VCR)
Presione para adelantar rápidamente la cinta o para ver la
imagen rápidamente en dirección de avance durante el modo
de reproducción. (Búsqueda en dirección de avance)
16. Botón C A STOP/EJECT
Presione para detener la cinta. Presione en el modo de
parada para retirar la cinta de la unidad.
17. Ventanilla del sensor de mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar
en privado.
19. Toma de entrada VIDEO
Conecte aquí la toma de salida de video de una
videocámara o de una videograbadora.
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
21. Compartimiento del cassette
22. Botón PICTURE
Presione para ajustar la imagen.
23. Botones numéricos
Modo TV/VCR:
Presione dos cifras para acceder directamente al canal
deseado.
No olvide presionar [0] antes de elegir un canal de una
sola cifra.
Botón +100
Presione para seleccionar canales de televisión por
cable cuyo número sea superior a 99.
Modo DVD:
Presione para introducir el número deseado.
Botón +10
Presione para introducir números superiors a 9.
24. Botón PAUSE F
Hace una pausa en la reproducción del disco o cinta.
25. Botón SPEED
Presione para seleccionar la velocidad de grabación
deseada: SP/SLP.
26. Botón C.RESET
Presione para poner el contador en 0:00:00.
Presione también para cancelar un ajuste de programa
de temporizador.
27. Botón DISPLAY
Modo TV/VCR:
Indica el contador o el número del canal y la fecha
actual en la pantalla del televisor.
Modo DVD:
Indica el estado actual en la pantalla del televisor.
28. Botón SETUP
Presione para entrar o salir del menú de configración
de televisor o DVD.
29. Botón TITLE
Para visualizar el menú de títulos.
30. Botón CLEAR
Presione para cancelar o borrar un ajuste entrado actualmente.
31. Botón MODE
Presione para llamar la pantalla de la reproducción
programada o la de reproducción aleatoria en el modo
de parada.
Presione para llamar la pantalla de ajuste del nivel del
negro o la pantalla de sonido ambiental durante la
reproducción.
– 50 –
ES
32. Botón SEARCH MODE
Presione para localizar un punto deseado.
33. Botón AUDIO
Modo DVD:
Presione para seleccionar un modo de sonido o idioma
de audio deseado.
34. Botón SUBTITLE
Presione para seleccionar el idioma de subtítulos
deseado.
35. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista
actual.
36. Botón ANGLE
Presione para cambiar el ángulo de la cámara y ver la
secuencia que se está reproduciendo desde un ángulo
diferente (si existe).
37. Botón A-B (modo DVD)
Repite la reproducción de una sección seleccionada.
38. Botón RETURN
Permite volver a la pantalla anterior en el menú de
configuración.
39. Botón ENTER
Presione para establecer un ajuste.
40. Botones K / L / { / B
Modo TV/VCR:
Presione para seleccionar un modo de ajuste en el
menú que aparece en la pantalla del televisor.
Presione también para seleccionar o establecer ajustes
en un menú en particular.
Modo DVD:
Presione para seleccionar un ítem de menú.
41. Botón DISC MENU
Muestra menú del DVD.
42. Botón ZOOM
Amplía parte de la imagen reproducida de un DVD.
43. Botón MUTE
Suprime la salida de sonido. Presione de nuevo para
restablecer el sonido.
44. Botón SLEEP
Utilice para ajustar el temporizador de dormir.
45. Toma ANT.
Conecte a una antena, sistema de televisión por cable o
sistema de satélite.
46. Cable de alimentación
Conecte a un toma de CA estándar (120 V, /60 Hz).
NOTA:
• Antes de conectar el cable de alimentación de una
toma de CA estándar, retírelo del gancho para evitar
dañarlo.
47. Toma AUDIO OUT COAXIAL
Conecte solamente a la entrada digital de un
amplificador externo o decodificador (para audio de
DVD solamente).
PREPARACIÓN PARA LA
UTILIZACIÓN
CONEXIONES DE ANTENA/CABLE
Consulte la figura 4 de la página 12
ANTENA COMBINADA DE VHF/UHF
La antena combinada de VHF/UHF de 75 ohmios puede
conectarse a la toma ANT.
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena exterior.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a la unidad, sin una
caja de convertidor.
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su compañía de televisión por cable le suministra
una caja de convertidor o si utiliza un sistema de
satélite, podrá utilizar la conexión básica que se
muestra en la ilustración.
La selección de los canales deberá hacerse con la caja de
convertidor o con la caja de satélite. Esto significa que
no es posible cambiar de canal utilizando el mando a
distancia de la unidad.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que
proporciona recomendaciones para hacer una
conexión a tierra apropiada y, en particular,
especifica que la tierra del cable debe conectarse
al sistema de puesta a tierra del edificio, tan cerca
del punto de entrada del cable como sea posible.
NOTA:
Antes de enchufar la antena a la toma ANT. de la
unidad, compruebe que la clavija no esté doblada.
Si esta doblada, póngala derecha como se muestra
en la ilustración, y luego conéctela en la toma
ANT. de la unidad.
Clavija doblada
PARA INSERTAR LAS PILAS
Cable Clavija
(Necesita enderezarse) (Clavija derecha)
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a
distancia en el sentido de la flecha.
2) Inserte 2 pilas “AA” en el
compartimiento de las pilas, en el
sentido indicado por las marcas de polaridad (+/-).
3) Vuelva a poner la cubierta.
NOTA:
• Para su seguridad y para evitar que se dañe
la unidad, desenchufe el cable de antena de la
toma ANT. antes de mover la unidad.
– 51 –
ES
CONEXIÓN A TOMAS DE
ENTRADA DELANTERAS
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada AUDIO/VIDEO de la parte delantera de la
unidad.
Conecte las tomas de salida de audio/vídeo de otra
fuente a las tomas AUDIO L/R y VIDEO de esta
unidad.
Después, presione [SELECT] o [CH. K / L] hasta
que aparezca “AUX” en la pantalla.
Si utiliza esta unidad para reproducir un disco DVD
grabado en formato de sonido envolvente Dolby
Digital de 5,1 canales, la unidad emitirá un flujo de
datos DOLBY DIGITAL desde su toma AUDIO
OUT COAXIAL. Si conecta la unidad a un
decodificador Dolby Digital, podrá disfrutar de una
tonalidad más convincente y real, con un sonido
envolvente potente y de alta calidad similar al de los
cines.
Utilice cables digitales coaxiales de audio
(disponibles en el comercio) para hacer las
conexiones de audio.
Consulte la figura 5 de la página 13
NOTA:
• Cuando conecte una videograbadora monofónica
(otra fuente) a esta unidad, conecte la toma de
salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de esta unidad. El
audio saldrá igualmente por los canales izquierdo y
derecho.
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS
DE ENTRADA DIGITAL (para DVD)
Utilice un cable digital coaxial de audio (disponible en
el comercio) para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
Consulte la figura 7 de la página 14
NOTAS:
• Asegúrese de apagar todos los componentes del
sistema antes de conectar otro componente.
• Consulte los manuales de instrucciones de los
componentes que va a conectar a la unidad.
• Si conecta un decodificador Dolby Digital, ajuste
la función “DOLBY DIGITAL” a “BITSTREAM”
para salida de audio en el modo de configuración.
• A menos que se haga la conexión a un
decodificador Dolby Digital, ajuste la función
“DOLBY DIGITAL” a “PCM” para salida de
audio en el modo de configuración. La
reproducción en una unidad utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede provocar daños a los altavoces.
Consulte la figura 6 de la página 13
NOTAS:
• La fuente de audio de un disco grabado en formato
de sonido envolvente Dolby Digital de 5,1 canales
no se puede grabar como sonido digital mediante
una platina MD o DAT.
• Asegúrese de apagar todos los componentes del
sistema antes de conectar otro componente.
• Consulte los manuales de instrucciones de los
componentes que va a conectar a la unidad.
• Ajuste la función “DOLBY DIGITAL” a “PCM”
para salida de audio en el modo de configuración.
La reproducción en una unidad utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede provocar daños a los altavoces.
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories.
– 52 –
ES
IDIOMA DEL MENÚ
SECCIÓN DE TV/VCR
TV/VCR
FUNCIONES Y AJUSTES
DE TV
1
PARA MIRAR UN PROGRAMA DE TV
TV/VCR
1
Enchufe el cable eléctrico
Encienda la unidad
Seleccione el número de canal
Presione [CH. K / L] o los botones numéricos para
seleccionar su número de canal deseado.
Nota para el uso de los botones numéricos:
¡Debe colocar un cero antes de los números de canal
de una sola cifra (por ejemplo: 02, 03, 04, etc.).
¡Cuando seleccione canales de cable de más de 99,
presione primero [+100] y después las dos últimas
cifras. (Ejemplo: para seleccionar el canal 125,
primero presione [+100] y después presione [2] y [5].)
4
2
3
Presione [POWER] para encender la unidad.
3
Presione [SETUP].
Presione [K / L] para apuntar al “LANGUAGE”.
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
Presione [ENTER] repetidamente para seleccionar
“ENGLISH” = inglés, “ESPAÑOL” o “FRANÇAIS”
= francés.
Enchufe el cable eléctrico de la unidad en un
tomacorriente de CA del hogar.
NOTA:
• Si aparecen números en la esquina de la pantalla,
presione [POWER] sin desenchufar el cable
eléctrico.
2
Seleccione “LANGUAGE”
Ajuste el sonido
Presione [VOL. X / Y] para ajustar el volumen.
Presione [MUTE] para silenciar instantáneamente el
sonido.
Presione nuevamente para recuperar el nivel de
sonido anterior.
NOTA:
• Si presiona [CH. K / L] en el modo DVD, puede
cambiar los canales de TV. Incluso si desconecta la
unidad en el modo DVD, cuando vuelva a
conectar, volverá al modo TV/VCR.
PARA VER CANALES DE CABLE O
SATELITE
Salga del modo de idioma
Presione [SETUP] para salir del menú.
NOTAS:
• Esta función afecta sólo el idioma en el menú de la
pantalla y no la fuente de audio.
• Si por alguna razón, el menú está en francés,
presione [SETUP], presione [K / L] para apuntar
al “LANGAGE [FRANÇAIS]” y presione
[ENTER] repetidamente para seleccionar el
idioma deseado y presione [SETUP].
AJUSTE DEL RELOJ
TV/VCR
AJUSTE MANUAL DEL RELOJ
Asegúrese ...
• La unidad debe estar encendida.
En el siguiente ejemplo, el reloj debe estar en:
FECHA
6 de mayo, 2005
HORA DE AJUSTE
5:40PM
1
Seleccione “AJUSTE RELOJ”
Presione [SETUP].
Presione [K / L] para selecciona “AJUSTE RELOJ”
y presione [ENTER].
2
Seleccione “AJUSTE MANUAL RELOJ”
• Si la unidad está conectada a una caja de cable o
Presione [K / L] para seleccionar “AJUSTE
MANUAL RELOJ” y presione [ENTER].
PARA VER UNA ENTRADA EXTERNA
Presione [K / L] hasta que aparezca el mes deseado.
(Ejemplo: Mayo → “05”)
Presione [B]. (O presione [s] para volver un paso.)
caja de satélite, presione [CH. K / L] para
seleccionar CH3 o CH4 de acuerdo con el ajuste
de canal de salida del dispositivo y seleccione el
canal deseado en el dispositivo.
3
Seleccione el mes
• Cuando se conecta un equipo externo en las tomas
de entrada AUDIO/VIDEO frontales, presione
[SELECT] o [CH. K / L] repetidamente hasta que
aparezca “AUX” en la pantalla.
4
Seleccione el día
Presione [K / L] hasta que aparezca el día deseado.
(Ejemplo: 6º → “06”)
Presione [B].
– 53 –
ES
5
GRABACIÓN
Seleccione el año
Presione [K / L] hasta que aparezca el año deseado.
(Ejemplo: “2005”)
Presione [B].
6
Seleccione los minutos
Presione [K / L] hasta que aparezcan los minutos
deseados.
(Ejemplo: “40”)
8
TV/VCR
SOLO puede ver el mismo programa que se está
grabando.
Seleccione la hora
Presione [K / L] hasta que aparezca la hora deseada.
(Ejemplo: “5”, “PM”)
Presione [B].
7
GRABACIÓN NORMAL
1
2
Haga funcionar el reloj
Presione [SETUP].
Aunque no aparezcan los segundos, empezará a
contar desde 00 cuando presione [SETUP]. Utilice
esta característica para sincronizar el reloj con la hora
real.
Seleccione el canal a grabar
Presione los botones numéricos o [CH. K / L].
NOTA:
• Si la unidad está conectada a una caja de cable o
caja de satélite, la unidad debe estar en CH3 o
CH4 y debe seleccionarse el canal a grabar en la
caja de cable o caja de satélite.
Seleccione la velocidad de la cinta
Presione [SPEED] para seleccionar la velocidad de
cinta deseada (SP/SLP).
3
Empiece a grabar
Presione [RECORD].
4
Pare la grabación
Presione [STOP C].
– 54 –
ES
REANUDACIÓN
SECCIÓN DE DVD
DVD-V
REPRODUCCIÓN BÁSICA
DVD-V
CD
1 Durante la reproducción, presione
CD
[STOP C].
¡Aparecerá el mensaje de continuación en la pantalla de TV.
Para empezar
¡Conecte la alimentación del amplificador y otros
componentes, si es necesario.
2 Presione [PLAY O], la reproducción continuará
desde el punto donde se paró la reproducción.
¡Para cancelar la continuación, presione dos veces
1 Presione [POWER].
[STOP C].
¡La alimentación se conectará.
¡La información de continuación permanece activada
incluso cuando apaga el interruptor principal.
2 Presione [A OPEN/CLOSE] para abrir la
bandeja de carga del disco.
3 Ponga el disco deseado en la bandeja, con
la etiqueta hacia arriba.
4 Presione [PLAY O].
¡La bandeja se cerrará automáticamente y la reproducción
comenzará desde el primer capítulo o pista del disco.
¡La reproducción también empieza cerrando manualmente
la bandeja del disco o presionando [A OPEN/CLOSE].
¡Si la reproducción no comienza automáticamente,
presione [PLAY O].
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pantalla.
5 Presione [STOP C] para detener la reproducción.
MENÚ DE DISCO
DVD-V
1 Presione [DISC MENU].
¡Aparecerá el menú principal de DVD.
¡Si no existe la función, puede aparecer el símbolo
en la pantalla de TV.
¡Si el menú de disco existe en el disco, aparecerán el
idioma de audio, opciones de subtítulo, capítulos para el
título y otras opciones para su selección.
2 Presione [K / L / s / B] para seleccionar
un ítem y presione [ENTER] para confirmar
la selección.
– 55 –
ES
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship
as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN
THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest FUNAI Authorized Service Center or for general service procedure, please
call or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-256-2487
http://www.EmersonAudioVideo.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
1EMN20210
T0101UB ★★★★★
Download PDF

advertising