advertisement
Owner’s Manual
Please read before using this equipment.
DVD/CD Player with Video Cassette Recorder
EWD2004
EMERSON AND THE G-CLEF LOGO ARE
REGISTERED TRADEMARKS OF
EMERSON RADIO CORP., PARSIPPANY,
NEW JERSEY, U.S.A.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call
TOLL FREE : 1-800-256-2487
or visit our web site at http://www.funai-corp.com
Supplied Accessory
• Remote control
(NB100UD or NB150UD) with two AA batteries
• RF cable
(WPZ0901TM002)
• Audio/Video cables
(WPZ0102TM015 or
WPZ0102LTE01)
• Owner’s Manual
(1VMN20189)
Owner's Manual
Table of Contents
Precautions
Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
■ Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Avoid the Hazards of Electrical Shock and Fire . . . . . . . . . . . . . . . 4
Moisture Condensation Warning . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbol Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setup
■ About the Video Cassettes and Discs . . . . . . . . . . . . . . . . . . . . 5
Playable Video Cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unplayable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
■ Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hint for Cable Box or Satellite Box. . . . . . . . . . . . . . . . . . . . . . . . . 6
Connection to an Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front & Rear Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ About the Remote Control and Front Panel . . . . . . . . . . . . . . . . 8
■ VCR/DVD Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
■ Preset for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turn on the unit for the first time . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clock Set Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
VCR Functions
■ Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
■ Recording & OTR (One Touch Recording) . . . . . . . . . . . . . . . . 11
■ Other Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
■ On-Screen Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
■ Recording Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Basic TV Connection / Conexión básica del televisor
Hint for Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Copying a Video Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
■ Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Time Search / Index Search / Auto Repeat . . . . . . . . . . . . . . . . . 14
DVD Functions
■ Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
■ The On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
■ Search Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Track Search / Title/Chapter Search / Time Search . . . . . . . . . . 17
■ Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
■ Repeat / Random / Programmed Playback . . . . . . . . . . . . . . . . 18
Repeat Playback / Repeat A-B Playback /
Random Playback / Programmed Playback . . . . . . . . . . . . . . . . . 18
■ Special Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Subtitle Language / Audio Language / Camera Angle /
Black Level Setting / Stereo Sound mode / Virtual Surround . . . . 19
■ DVD Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
LANGUAGE Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DISPLAY Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AUDIO Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PARENTAL Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To return the All Selections of SET UP
(except for PARENTAL) to the Default Setting . . . . . . . . . . . . . . . 22
Information
■ Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
■ Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
■ Language List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
■ Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Quick Use Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cable
Signal
Señal de Cable
Antenna
Antena or o
(Back of TV)
Disconnect
Desconecte
(Parte posterior de una TV)
Cable
Signal
Señal de Cable
Antenna
Antena or o
2
Connect
Conexiones
(Back of
DVD/VCR)
( Parte posterior del reproductor
DVD/VCR)
3
Connect
ANT-IN
Conexiones
ANT-OUT
(Back of TV)
(Parte posterior de una TV)
RF Cable (supplied)
Cable RF (incluíd)
5
Please refer to "Connections" on page 5.
AC outlets
Toma de CA
4
Plug in
Enchufe
From DVD/VCR
De la DVD/VCR
From TV
De la TV
Precautions
WARNING
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION:
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI-
FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO
BEAM.
LOCATION:
INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING-
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
For Customer Use:
Read carefully the information located at the back of this unit and enter below the Serial No.Retain this information for future reference.
Model No.
_____________________
Serial No.
_____________________
– 2 –
EN
Important Safeguards
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. Attachments - Do not use attachments not recommended by the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories - Do not place this video product on an unstable cart, stand, tripod, bracket, or table.The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
MEUBLES - Ne pas installer cet appareil sur un meuble, un socle, un support, un trépied ou une table instables. L'appareil pourrait tomber, provoquant des blessures graves à un enfant ou un adulte, et être sérieusement endommagé. Utiliser uniquement un chariot, un support, un trépied ou une table recommandés par le fabricant, ou bien vendus avec l'appareil. Suivre les directives du fabricant pour le montage de l'appareil et n'utiliser que les accessoires de montage recommandés par ce dernier. Si on l'installe sur un meuble à roulettes, déplacer les deux ensemble avec précaution. Un arrêt brusque, l'utilisation d'une force excessive et des surfaces irrégulières risquent de déstabiliser l'ensemble et de le renverser.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered.The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This video product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where
– 3 –
they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
NEC – NATIONAL ELECTRICAL CODE
S2898A
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
14. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.
18. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in performance this indicates a need for service.
20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.
22. Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
EN
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the power cord immediately and take the unit to our
Authorized Service Center for servicing.
• Do not put your fingers or objects into the DVD/VCR cassette holder.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours until its inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Symbol Used in This Manual
The following symbols appear in some headings and notes in this manual.
Maintenance
SERVICING
¡Please refer to relevant topics on the Troubleshooting
Guide on page 23 before return the product.
¡When this unit become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug, and please call our help line mentioned on the front page to locate an Authorized Service Center.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a circular motion.
¡Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.
CLEANING THE DISC LENS
¡If this unit still does not perform properly although you refer to the relevant sections and to “TROU-
BLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
¡Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is not used.
AUTO HEAD CLEANING
¡Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
¡Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line mentioned on the front page to locate an Authorized Service Center.
NOTES:
¡Remember to read the instructions along with the video head cleaner before use.
¡Clean video heads only when problems occur.
: Description refers to playback or recording of video cassette tapes.
: Description refers to playback of DVD-Video discs.
: Description refers to playback of Audio CDs.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
– 4 –
EN
Setup
About the Video Cassettes and Discs
Playable Video Cassettes
Use only cassettes marked
Playable Discs
Playable discs
Mark (logo)
DVD-Video
* 1,2,4,6 with this unit.
Region code
or
Recorded signals
Disc size
DVD-R
DVD-RW
* 1,2,3,4,5,6
-
Digital video
(MPEG2)
12 cm or
8cm
Disc types
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
DVD+R
DVD+RW
* 1,2,3,4,5,6
-
Audio CD
* 4,6
CD-R
CD-RW
* 4,5,6
-
Digital audio
12 cm or
8cm
Digital audio
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Only the discs which have been recorded in the video format and finalized can be played back.
Discs unfinalized or recorded in the video recording format cannot be played back.
Depending on the recording status of a disc, the disc may not be played back at all or normally
(the picture or sound may be not be smooth, etc.).
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or special properties of discs.
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not play them back.
Even if they are played back, the sound or video quality will be compromised.
Unplayable Discs
¡On the following discs, only the sound can be heard (picture cannot be viewed).
CDV CD-G
¡NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM CD-I Photo CD
Video CD
DTS-CD
MP3
DVD with region codes other than 1 or ALL
DVD-ROM for personal computers
CD-ROM for personal computers
¡On the following disc, the sound MAY NOT be heard.
Super Audio CD
Note: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
¡Any other discs without compatibility indications.
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press the OUTPUT button on the DVD/VCR so that the VCR OUTPUT light is lit.
• If noise appears on the TV screen, press the VCR/TV button on the remote control.
4) Press the PLAY button once.
5) After a few seconds, press the PLAY button on the DVD/VCR for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
• When a picture does not appear on the TV screen, repeat step [4].
6) Press the STOP button to stop playback.
– 5 –
• The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback and start the playback again.
After that, press the PLAY button on the DVD/VCR for 3 seconds again.
EN
Hint for Cable Box or Satellite Box
Connection A
Cable
Signal
(Cable box or
Satellite box)
IN
OUT
ANT-IN
ANT-OUT
(Back of DVD/VCR)
E
Connection B
Cable
Signal
ANT-IN
ANT-OUT
(Back of DVD/VCR)
(Cable box or
Satellite box)
IN
OUT
E
RF Cable
(supplied)
(Back of TV)
Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the DVD/VCR. You can view or record ONLY the channels you have selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be viewed.
To select channels of the cable box or satellite box
1) Turn on the DVD/VCR by pressing the POWER button, and then, press the VCR/TV button.The “POWER” light on the front panel will appear. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).
• If you use the channel 4, you need to change the DVD/VCR’s
RF output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3) At the cable box or satellite box, select the channel you want to view or record.
RF Cable
(supplied)
RF Cable
(Back of TV)
Select this connection when you want to change channels on the
DVD/VCR. With this connection, you may watch one channel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1) At the cable box or satellite box, select channel 3 or 4 (the same channel as the DVD/VCR’s RF output channel.)
• Refer to “RF Output Channel”.
2) At the TV, select the same channel as the output channel (3 or
4) of the cable box or satellite box.
3) Turn on the DVD/VCR by pressing the POWER button, and then, press the VCR/TV button. The “POWER” light on the front panel will appear. Then, select the channel you want to view or record.
To play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 11.
To view one channel while recording another
1) While you are recording on the DVD/VCR, press the VCR/TV button.
2) At the cable box or satellite box, select the channel you want to view.
Connection to an Audio System
AUDIO
Method 1
Stereo system
Analog audio input jacks
L R
Method 2
Dolby Digital decoder,
MD deck or DAT deck
DVD/VCR
Audio cable
(supplied)
(Analog)
AUDIO OUT
DVD/VCR
AUDIO OUT
L
VCR
AUDIO IN
R
VIDEO OUT VIDEO IN
COAXIAL
Digital audio input jack
Audio Coaxial
Digital cable
(commercially available)
DIGITAL
AUDIO OUT
DIGITAL
AUDIO OUT
COAXIAL
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
L
C
B
R
C
R
DIGITAL
AUDIO OUT
COAXIAL or
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
L
C
B
R
C
R
Note
• If output is Dolby Digital encoded audio, connect to a Dolby
Digital decoder, and set “DOLBY DIGITAL” to “ON” in the
AUDIO menu. (Refer to pages 20-21.)
• The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an
MD or DAT deck.
• Unless connected to a Dolby Digital decoder, set “DOLBY
DIGITAL” to “OFF” in the AUDIO menu. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (Refer to pages 20-21.)
• Set “DOLBY DIGITAL” to “OFF” in the AUDIO menu for connecting to an MD deck or DAT deck. (Refer to pages 20-
21.)
• By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality 5.1ch Dolby Digital surround sound as heard in the movie theaters.
– 6 –
EN
Connection to a TV
TV
Basic Audio
L
AUDIO IN
R
Method 1
Good picture
VIDEO IN
Method 2
Better picture
S-VIDEO IN
Method 3
Best picture
COMPONENT
VIDEO IN
Y
C
B
C
R
DVD/VCR
Audio cable
(supplied)
Video cable
(supplied)
S-Video cable
(commercially available)
DVD/VCR
AUDIO OUT
L
VCR
R
VIDEO OUT
AUDIO IN
ANT-IN
ANT-OUT
VIDEO IN
DVD/VCR
AUDIO OUT
L
VCR
AUDIO IN
R
VIDEO OUT VIDEO IN
Component
Video cables
(commercially available)
DIGITAL
AUDIO OUT
COAXIAL
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
L
L
CB
R
R
VCR
AUDIO IN
CR
VIDEO OUT VIDEO IN
DIGITAL
AUDIO OUT or
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONEN
VIDEO OUT
L
C
COAXIAL
R
C
VIDEO OUT
DIGITAL
AUDIO OUT
COAXIAL
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
L
C
B
R
C
R
S-VIDEO OUT
DIGITAL
AUDIO OUT
COAXIAL
DVD
AUDIO
OUT
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
L
C
B
R
C
R
COMPONENT VIDEO OUT
(Analog) AUDIO OUT
Note
• Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.
• The COAXIAL, DVD AUDIO OUT, S-VIDEO OUT and COMPONENT VIDEO OUT jacks are only useful in DVD mode.
Front & Rear Terminals
DVD ANALOG AUDIO OUT jacks
Connect the supplied audio cables here through the Audio
In jacks of a television or other audio equipment. (DVD only)
DVD/VCR AUDIO OUT jacks
Connect the supplied audio cables here through the audio
In jacks of a television or other audio equipment.
AUDIO IN jack
Connect audio cable coming from the audio out jack of a camcorder, another VCR, or an audio source here.
ANT IN jack
Connect your antenna or cable box here.
COAXIAL jack
Connect an optional coaxial digital audio cable here through the coaxial digital audio in jack of a decoder or audio receiver. (DVD only)
S-VIDEO OUT jack
Connect an optional
S-Video cable here through the S-video in jack of a television. (DVD only)
COMPONENT VIDEO
OUT jacks
Connect optional component video cables here through the component video in jacks of a television.
(DVD only)
ANT-IN
DIGITAL
AUDIO OUT
DVD
AUDIO
OUT
COAXIAL
L
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
DVD/VCR
AUDIO OUT
Y
DIGITAL
AUDIO OUT
DVD
AUDIO
L
C
B
COAXIAL
R
L
R
VCR
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
L
VCR
AUDIO IN
AUDIO IN
CB/
PB
R
VIDEO OUT VIDEO IN
CR/
PR
VIDEO OUT VIDEO IN
C
R
ANT-IN
ANT-OUT
ANT-OUT
[Back of DVD/VCR]
DVD/VCR VIDEO OUT jack
Connect the supplied yellow video cable here through the TV’s video in jack.
VIDEO IN jack
Connect a cable coming from the video out jack of a camcorder, another VCR, or an audio-visual source
(laser disc player, video disc player, etc.) here.
VIDEO AUDIO
POWER REW F.FWD
S
[Front of
DVD/VCR]
ANT OUT jack
Connect the supplied RF cable to the antenna input jack on your TV.
– 7 –
EN
Remote Control
Installing the Batteries for the Remote Control
Install two AA batteries
(supplied) matching the polarity indicated inside battery compartment of the remote control.
23 f
1
2
3
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7
DISPLAY
8
0
VCR
2
5
9
+10
DVD
3
6
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
MENU ENTER
SETUP TOP MENU
SUBTITLE
T-SET
ANGLE REPEAT
RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
A-B
Keep in mind the following when using the remote control:
• Make sure that there is no obstacle between the remote and the remote sensor on the unit.
• Use within the operating range and angle, as shown.
Within about
Remote control
DVD mode
Button
Disc/Tape
(Alphabetical order)
1 2 3
4
7
5
8
0
6
9
+10
• To select chapter or title directly. • To select track directly.
ENTER
A-B
ANGLE
AUDIO
CLEAR/
C. RESET
DISPLAY
DVD
MENU
•
•
VCR mode
To select channel.
The +10 button has no effect in VCR mode.
• To search forward/backward through a disc.
• To begin slow forward/reverse playback during the pause mode.
• To search forward/backward through a disc.
• To forward/backward a tape.
• To move the cursor and determine its position.
• To move the cursor and determine its position.
• To select an item
on the VCR Menu.
• To advance to the next
VCR Menu.
• To go back one step during
clock and timer setting.
• To repeat between your chosen point A and B.
• To select camera angles on a disc.
• To repeat between your chosen point A and B.
• To select audio languages on a disc.
• To select STEREO,
L-CH or R-CH.
• To clear the markers.
• To clear the numbers entered incorrectly.
• To clear the markers.
• To remove status No. in program input.
• To clear the numbers entered incorrectly.
•
•
To exit the VCR Menu.
To reset the tape counter.
• To display the current disc mode.
• To display the current disc mode.
• To select the DVD output
mode.
• To activate the remote control
in DVD mode.
• To select the DVD output
mode.
• To activate the remote control
in DVD mode.
• To display the current time,
tape counter, and channel.
• To call up the Menu
on a disc.
• To call up the VCR Menu.
MODE
• To set black level on/off.
• To arrange the playing order or play randomly.
OPEN/CLOSE
/EJECT
PAUSE
• To open or close the disc tray.
• To pause disc playback.
• To advance playback one frame at a time.
• To begin disc playback.
• To open or close the disc tray.
• To pause disc playback.
• To begin disc playback.
• To eject the video cassette from the VCR.
• To pause tape playback or recording.
• To advance playback one frame at a time.
• To begin tape playback.
PLAY
POWER
• To turn the unit on or off.
• To turn the unit on or off.
• To turn the unit on or off.
REC/OTR
• To start a recording.
REPEAT
RETURN
SEARCH
MODE
SETUP
SKIP/CH.
SKIP/CH.
SLOW
SPEED
• To play a chapter or title repeatedly.
• To play a track or disc repeatedly.
• To return to the previous operation on the DVD setup menu.
• To return to the previous operation on the DVD setup menu.
• To search chapter, title or time.
• To rapidly return to a location of disc.
• Search the markers.
• To search track.
• To search time.
• To rapidly return to a location of disc.
• Search the markers.
• To call up the DVD setup
menu.
• To call up the DVD setup
menu.
• To call up the index or time
search menu.
• To skip chapters.
• To skip tracks.
• To change channels.
• To adjust the tracking manually
during playback.
• To view the tape in slow motion.
•
To select the recording speed.
STOP
SUBTITLE
T-SET
TOP MENU
VCR
VCR/TV
V.SURR.
• To stop playback.
• To stop playback.
• To stop playback or recording.
• To select subtitles on a disc.
• To put the VCR into standby mode for a timer recording.
• To call up the Top Menu on a disc.
• To select DVD position or
TV position.
• To select CD position or TV position.
• To select the VCR output mode.
• To activate the remote control in VCR mode.
• To select VCR position or
TV position.
• To set virtual surround on/off. • To set virtual surround on/off.
– 8 –
EN
Front Panel Display
Lights up when power is on.
Lights up when the disc is inserted.
Lights up during a recording.
Flashes when a recording is paused.
Lights up when the inserted disc is being played back.
Flashes when an unacceptable disc is installed.
CHANNEL
OPEN/CLOSE
VCR OUTPUT DVD DISC IN
SKIP/REV STOP PLAY FWD/SKIP
VIDEO AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR
Lights up when the timer recording or an OTR recording has been set.
VCR/DVD Switching
Because this product is a combination of a VCR and a DVD player, you must select first which component you wish to operate with the OUTPUT button.
VCR MODE
Press the VCR button on the remote control.
(Verify that the VCR OUTPUT light is lit.)
DVD MODE
Press the DVD button on the remote control.
(Verify that the DVD OUTPUT light is lit.)
Note
• Pressing only the OUTPUT button on the
front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.
VIDEO AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR
VCR
OUTPUT
CHANNEL
DVD
OPEN/CLOSE
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
VCR
OUTPUT
DVD DISC IN
SKIP/REV STOP PLAY FWD/SKIP
VCR button
DVD button
1 2
4
7
DISPLAY
0
VCR
5
8
3
6
9
+10
DVD
SKIP/CH.
VCR/TV
SLOW
PAUSE
SKI
DVD OUTPUT light
OUTPUT button
PLAY
STOP
REC/OTR
MENU ENTER
SETUP TOP MENU
SUBTITLE
T-SET
ANGLE REPEAT
RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
A-B
VCR OUTPUT light
– 9 –
EN
Preset for Use
Turn on the unit for the first time
VCR
Turn on the TV and set it to channel 3.
• If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.
POWER
Remote Control TV Screen or
LANGUAGE SELECT
[ON]
B
ENGLISH
FRANCAIS
ESPAÑOL
To Preset the Channel Again
1) Press the MENU button until the main menu appears.
2) Select "CHANNEL SET UP" by pressing the K or L button. Then, press the B button.
3) Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button.
After scanning, the tuner stops on the lowest memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main menu appears.
2) Select "LANGUAGE SELECT" by pressing the K or L button. Then, press the B button.
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing the K or L button. Then, press the CLEAR/C.RESET
button.
or or
CLOCK SET
MONTH DAY
0 3 / 1 5
YEAR
2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
Select the current year
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
Select the current hour
AUTO SET UP
CH 01
Do you connect the cable from the cable box or the satellite box to the DVD/VCR’s ANT IN jack?
YES
Y es
Press the MENU button to exit
• Refer to “Hint for Cable Box or Satellite Box” section on page 6.
NO
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using the CHANNEL buttons.
• If "AUTO SET UP" appears on the TV screen again, check the cable connections.
Then press the
B button once again.
• If you accidentally select Spanish or
French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press the B button, and select ENGLISH. Finally, press the CLEAR/C.RESET button.
Clock Set Up
VCR
MENU
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B
CLOCK SET
LANGUAGE SELECT or or
• If the clock is not set, the
CLOCK SET screen appears when you press the MENU button. In this case, go to step [2].
CLOCK SET
MONTH DAY
0 3 / – –
YEAR
– – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
• Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by directly entering channel using the Number buttons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press 1,1,7)
• You must precede single-digit channel numbers with a zero (For example:
02, 03, 04 and so on).
or
CLOCK SET
MONTH DAY
0 3 / 1 5
YEAR
– – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current day
– 10 –
or or
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
Select the current minute
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Select “AM” or “PM”
8
To exit the CLOCK SET screen.
• To go back one step, press the s button
(during the steps [2] to [7].)
• Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds.
EN
VCR Functions
Playback
Before:
Turn on the TV and set it to channel 3.
• If channel 3 is already occupied for broadcasting, see “RF Output Channel” section.
VCR
Remote Control TV Screen
PLAYB
PLAY
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1 2
4
7
DISPLAY
0
VCR
5
8
3
6
9
+10
DVD
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
VIDEO AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR
STOP
STOP
OPEN/CLOSE
/EJECT
EJECT
A
CHANNEL
OPEN/CLOSE
V
• When a tape without record tab is inserted, the
DVD/VCR will start playback automatically.
• Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press the CHAN-
NEL buttons.
Recording & OTR (One Touch Recording)
Before:
Turn on the TV and set it to channel 3.
• If channel 3 is already occupied for broadcasting, see “RF Output Channel” section.
VCR
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
Remote Control TV Screen with tab
SPEED
1
4
7
2
5
8
0
3
6
9
SKIP/CH.
CH12
• Select the desired channel
SP
• Select the desired tape speed
Tape Speed Recording/Playback Time
Type of tape
SP mode
SLP mode
T60
1hour
3hour
T120
2hours
6hour
T160
2-2/3hours
8hour
REC/OTR
REC
You can select a fixed recording time by pressing the REC/OTR button repeatedly.
REC OTR(0:30) OTR(1:00).....
(Normal recording)
OTR(8:00) OTR(7:30)
1
4
7
DISPLAY
8
0
VCR
2
5
9
+10
DVD
3
6
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
ENTER
RETURN
VIDEO AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, remove its record tab. To record on it later, cover the hole with cellophane tape.
You CAN NOT copy a DVD to a videotape.
STOP
STOP
OPEN/CLOSE
/EJECT
EJECT
A
Record tab
To stop recording temporarily (Pause mode)
Press the PAUSE/STILL button.
• During the rec-pause mode, five C marks appear on the TV screen. Each C mark represents one minute.
• Press it again to resume recording.
CHANNEL
OPEN/CLO
• To view one channel while recording another
1) While you are recording on the
DVD/VCR, press the VCR/TV button.
2) At the cable box or satellite box, select the channel you want to view.
• If you have connected the DVD/VCR to a cable box or satellite box, refer to
“Hint for Cable Box or Satellite Box” section on page 6.
Other Operations
To cue or review picture during playback
(Picture Search)
Press the F.FWD or REW button.
• Press it again and the DVD/VCR will search in super high speed. (in the LP/SLP modes only)
To freeze the picture on TV screen during playback (Still mode)
Press the PAUSE/STILL button. Each time you press the button, the picture will be forwarded by one frame.
• If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing the
CHANNEL buttons.
• If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if equipped.
Counter Reset
Press the CLEAR/C.RESET button.
To play back in slow motion
Press the SLOW button during playback or the still mode.
• If the noise bars appear on the TV screen, you can reduce it by pressing the CHANNEL buttons.
Auto Rewind
When a tape reaches its end during playback, fast-forward, or recording (except timer recording and One
Touch Recording), the tape will automatically rewind to the beginning. After rewinding finishes, the
DVD/VCR will eject the tape.
– 11 –
• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the video head.
• To return to playback from the Picture
Search/Still/
Slow mode, press the PLAY button.
EN
On-Screen Operations
VCR
1
To call up the main menu
-MENU-
MENU
B
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
2
To select an item
-MENUor
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
3
To decide
CHANNEL SET UP
AUTO SET UP
B
MANUAL SET UP
4
To exit the menu
CLEAR/
C. RESET
MENU
OR
Recording Features
Timer Recording
•Insert a tape with its record tab into the DVD/VCR.
VCR
MENU
-MENU-
B
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
5
Select the desired start time
(hour) or
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
Select the minute or or
PROGRAM NUMBER 4
DATE – – / – –
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
Select an empty program number
PROGRAM NUMBER 4
B
ONCE
DAILY
WEEKLY or
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
AM
B
PM
Select “AM” or “PM” or
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”
4
Select the desired month
ONE TIME PROGRAM or
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
Select the desired day or
• You can program one year in advance.
1 2
4
7
5
8
DISPLAY
0
VCR
3
6
9
+10
DVD
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
ENTER
RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
SUBTITLE
T-SET
ANGLE REPEAT A-B or
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP B SP
SLP
Select the desired recording speed
• To set another program after step [9], press the
B button. Then continue with step [2].
CLEAR/
C. RESET
SUBTITLE
T-SET
• TIMER REC light on the front panel appears.
The DVD/VCR will change to the DVD mode.
7
Repeat the procedure in steps 5 and 6 to set the end time.
or
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 0 5 / 0 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
Select the desired channel
• If you have connected the DVD/VCR to a cable box or satellite box as the
Connection A on page 6, select the VCR to channel 3 or 4 (the RF output channel of the VCR). Then select the desired channel at the cable box or satellite box. Leave the cable box or satellite box on for timer recording.
– 12 –
• To go back one step, press the s button (during the steps [3] to [9].)
To Check, Correct, or Cancel a
Timer Program
1) Press the SUBTITLE/T-SET button then the VCR button on the remote control.
2) Select main menu by pressing the
MENU button.
3) Select "TIMER PROGRAMMING" by pressing the
K or L button. Then press the B button.
4) Select the program number which you want to check by pressing the K or L button. The details of the program you selected will appear on the TV screen.
• Go to the digit you want to change by pressing the B or s button. Then enter correct numbers by pressing the K or L button.
• You may cancel the entire program by pressing the s button while the program number flashes.
5) Press the CLEAR/C.RESET button to exit.
6) Press the SUBTITLE/T-SET button to return to timer stand-by mode.
To cancel a Timer Recording in progress
Press the STOP/EJECT button on
the DVD/VCR.
EN
Hint for Timer Recording
• If there is a power failure or the DVD/VCR has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a tape is not in the DVD/VCR or does not have the record tab, the TIMER REC light flashes and timer recording cannot be performed. Please insert a recordable tape.
• If a tape ends during timer recording, the VCR will stop, eject the tape and switch to the DVD mode automatically as the TIMER REC light flashes. (If the DVD power is off, the VCR will become STANDBY status.)
• When all timer recordings are finished, the TIMER REC light will flash.
• When timer recordings are set, the TIMER REC light will appear. To use the VCR as usual until the time
for the recording, press the SUBTITLE/T-SET button so that the TIMER REC light disappears. Press the
VCR/TV button to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual.
If you want to use the DVD player during a VCR timer recording or while the TIMER REC light is on or flashes.
• You can use the DVD player while the TIMER REC light is on or flashes, or during a timer recording. Press the POWER button to turn on the DVD. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don’t have to set the TIMER off to use the DVD only.
Copying a Video Tape
Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
(Back of TV)
(Back of another source) or
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
L
VCR
L
C B R
VIDEO OUT
C R
R
1
ANT-IN DIGITAL
AUDIO OUT
Connect
ANT-OUT COAXIAL
DVD
AUDIO
OUT
L
R
Audio/Video cables
(not supplied)
(Back of Recording DVD/VCR*)
Y
DVD/VCR
AUDIO OUT
L
VCR
C B R
VIDEO OUT
C
R
AUDIO IN
VIDEO IN
R
ANT-IN
2
Connect
ANT-OUT
RF cable
(supplied)
*Front input jacks are also available
• For best results during dubbing, use the front panel controls whenever possible. The remote control might affect another source’s operation.
• Always use video-quality shielded cables with RCA-type connectors.
Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver or other audio/video component with A/V outputs.
• “L1” or “L2” is found before the lowest memorized channel. (Example:
CH02)
• “L2” input jacks are on the front of this DVD/VCR.
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording
DVD/VCR.
3) Press the SPEED button on the remote control of the recording DVD/VCR to select the desired recording speed (SP/SLP).
4) Select the "L1" or "L2" position on the recording
DVD/VCR.
• To use the input jacks on the back of this unit, select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons.
• To use the input jacks on the front of this unit, select "L2" position by pressing [0], [0], [2] on the remote control or the CHANNEL buttons.
5) Press the REC/OTR button on the recording
DVD/VCR.
6) Begin playback of the tape in another source.
7) To stop recording, press the STOP/EJECT button on the recording DVD/VCR, then stop playback of the tape in another source.
– 13 –
EN
Special Features
Time Search
You can specify the time for fast forwarding or rewinding.
• Insert a tape into this unit.
VCR
Index Search
You can specify the number of programs to be skipped.
• Insert a tape into this unit.
VCR
Auto Repeat
You can repeat playback of a whole tape automatically.
• Insert a tape into this unit.
VCR
MENU
SEARCH
MODE x2 (Twice)
TIME SEARCH
– : – –
SEARCH
MODE x1 (Once)
INDEX SEARCH
– – or
-MENU-
TIMER PROGRAMMING
B
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
2
Select the desired length of time for fast forwarding or rewinding
TIME SEARCH
2 : 5 0 or or
INDEX SEARCH
0 3
-MENU-
TIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
0:01~ 9:59
(1 minute~9 hours and 59 minutes)
CURRENT PROGRAM
Beginning of tape
Pro.1
Pro.2
Pro.3
Pro.4
Pro.5
01 ~ 20
End of tape
02 01 01 02 03
INDEX MARK
AUTO REPEAT B
To rewind To fast forward
3
To rewind To fast forward
After searching,
After searching,
PLAY
B
PLAYB
• This unit stores index mark at the beginning of the recording. There should be time gap between two index marks for the Index Search.
Hint f or Timer Sear c h & Inde x Sear c h
• These functions are not available during recording.
• Press the STOP button to stop the search.
• If the end of the tape is reached during a Search, this unit will cancel the search and rewind the tape.
• To cancel Auto Repeat, follow steps [1]-[2] above.
Then press the B button, so that [OFF] appears beside AUTO REPEAT. Press the
CLEAR/C.RESET button to exit.
• If menu remains on the TV screen at step [3], press the CLEAR/C.RESET button to exit.
– 14 –
EN
DVD Functions
Playback
Before: Turn on the TV, amplifier and any other components which are connected to this unit. Make sure the TV and audio receiver
(commercially available) are set to the correct channel.
DVD
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7
DISPLAY
8
0
VCR
2
5
3
6
9
+10
DVD
SKIP/CH.
VCR/TV
SLOW
PAUSE
OPEN/CLOSE
/EJECT
POWER
PLAY
STOP
REC/OTR
Remote Control TV Screen
STOP
PLAY
OPEN/CLOSE
VCR
OUTPUT
DVD DISC IN
SKIP/REV STOP PLAY FWD/SKIP
AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR CHANNEL
OPEN/CLOSE
/EJECT
• A “prohibited icon” may appear at the top-right on the TV screen when the operation is prohibited by the disc or this unit.
• Some DVDs may be played from title 2 or 3 due to specific programs.
• During the playback of a two-layered disc, pictures may stop for a moment. This happens while the 1st layer is being switched to the
2nd layer. This is not a malfunction.
DVD menu
DVDs may contain menus to access special features. Press appropriate Number buttons or use the arrow (K/L/ s
/
B
) buttons to highlight your selection on the DVD main menu and press the ENTER button to confirm.
Calling up a Menu Screen during Playback
•
•
Press the MENU button to call up the DVD menu.
Press the TOP MENU button to call up the title menu.
•
Note
Menu operations may vary depending on the disc. Refer to the manual accompanying the disc for details.
Resume
Press the STOP button. Resume message will appear on the TV screen.
Press the PLAY button, playback will resume from the point at which playback was stopped.
•
To cancel resume, press the
STOP button one more time during the Stop mode.
Press 'PLAY' to play from here.
To play the beginning, press 'STOP' first and then 'PLAY'.
Paused and Step-by-Step Playback
Press the PAUSE button during playback.
T o contin ue pla ybac k, press the PLA Y b utton.
To use the SKIP/REV, FWD/SKIP buttons on the
Main Unit
Press once to skip chapters or tracks to a desired point.
Press and hold to change forward or reverse playback speed.
Fast Forward/Reverse Search
Press the g h
button repeatedly dur-
ing playback to select the required forward or reverse speed.
T o contin ue pla ybac k, press the PLA Y b utton.
E
1
•
For DVDs, fast forward or reverse search speed is different depending on the disc. Approximate speed is 1 (x2), 2 (x8),
3 (x50), 4 (x100).
•
For Audio CDs, approximate speed is x16.
Slow Forward/Slow Reverse
Press the g h
button repeatedly dur-
ing the pause mode to select the required forward or reverse speed.
T o contin ue pla ybac k, press the PLA Y b utton.
•
Slow forward or reverse speed is different depending on the disc. Approximate speed is 1 (1/16), 2 (1/8), 3 (1/2).
1
• Set “STILL MODE” to “FIELD” in the Display menu if pictures in the slow playback mode are blurred. (Refer to pages 20-21.)
The disc goes forward by one frame each time the PAUSE
button is pressed during the pause mode.
T o contin ue pla ybac k, press the PLA Y b utton.
• Set “STILL MODE” to “FIELD” in the Display menu if pictures in the pause mode are blurred. (Refer to pages 20-21.)
– 15 –
EN
The On-Screen Display
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
DVD DVD
DISPLAY
DISPLAY
11/16 0:00:00 - 0:03:30
DISPLAY
1/3 0:00:00 - 1:23:45
DISPLAY
Current playback status
Remaining time of the current chapter
Elapsed time of the current chapter
CH(Chapter):
Current chapter number / Total chapters
Remaining time of the current title
Elapsed time of the current title
TT(Title):
Current title number / Total titles
4/12 0:03:21 - 0:02:15 T
DISPLAY
4/12 0:13:45 - 0:45:40
T
DISPLAY
Current playback status
Remaining time of the current track
Elapsed time of the current track
TR(Track):
Current track number / Total tracks
ALL:
Current track number / Total tracks
Current repeat setting appears only when the repeat setting is active
T: Track repeat
A: All Tracks repeat
A B: A-B repeat
Remaining time of the current audio CD
Elapsed time of the current audio CD
T L1
Layer numbers, appears only when playing a two-layered Disc
L0: Layer 0 is playing
L1: Layer 1 is playing
Current repeat setting appears only when the repeat setting is active
C: Chapter repeat / T: Title repeat /
A B: A-B repeat
BIT RATE: The amount of audio and video data currently being read
DISPLAY
– 16 –
EN
Search Function
Track Search
DVD
Title / Chapter Search
DVD
Time Search
DVD
Using the n
1
4
7
2
5
8
0
3
6
9
+10
umber b
/2
uttons
•For single digit tracks (1-9), press a single number (eg. track 3, press 3).
•To play track 26, press +10, 2, 6 of the
Number buttons.
Using the SEARCH MODE b utton
SEARCH
MODE
/2
1
4
7
2
5
8
0
3
6
9
+10
/2
Within 30 seconds
Using the SKIP
H
,
,
G
b uttons
PLAY
SKIP/CH.
Current Track
(TR)
SKIP
TR 1 TR 2 TR 3 TR 4
SKIP
Using the SEARCH MODE b utton
PLAY
TOTAL
1:29:00
/12
SEARCH
MODE
Press once for the chapter search
Press twice for the title search
1
4
7 8
0
2
5
9
+10
3
6
/12
Within 30 seconds
SEARCH
MODE
Press repeatedly until this screen appears
1
4
7
2
5
8
0
3
6
9
TOTAL
1:29:00
Within 30 seconds
Using the SKIP
H
,
,
G
b uttons
PLAY
SKIP/CH.
Current Chapter
(CH)
SKIP
CH 1 CH 2 CH 3 CH 4
SKIP
Note
¡Depending on the disc being played, this function can also be performed by directly entering the desired chapter number with the number buttons.
Refer to the manual accompanying the disc.
• For Time Search, “0” appears automatically when there is no need to enter a number.
For example, “0:0_:_ _” appears in the Time Search screen if the total time of the disc is less than 10 minutes.
Marker Setup
DVD
This feature allows you to assign a specific point on a disc to be called back later.
T o set a marker
T o return to the marker
PLAY
T o e xit the marker screen
RETURN
PLAY
SEARCH
MODE
Press repeatedly until this screen appears
SEARCH
MODE Press repeatedly until this screen appears or or
Notes
¡Opening the disc tray or turning off the power will erase all markers.
¡Selecting “AC” at step [2] in the section “To set a marker” will also erase all markers.
¡To clear a marker, select the marker to be cleared at step [2] and then press the CLEAR/C.RESET button.
at the desired marker
•Playback will restart from the specific point which you set.
– 17 –
EN
Repeat / Random / Programmed Playback
Repeat Playback Repeat A-B Playback
DVD
Programmed Playback
DVD
DVD
Repeat function is available only during playback.
You may determine the order in which tracks will play.
PLAY
A-
STOP
PLAY
A-B at your desired starting point (A).
REPEAT
MODE
Press once
ENTER
CD-DA TOTAL 0:00:00
Each time the REPEAT button is pressed...
A-B
A-B
CHAPTER
(current chapter repeat)
TITLE
OFF
TRACK
at your desired end point (B).
¡
Point B should be in the same title or track as point A is.
(current title repeat)
(repeat off)
(current track repeat)
¡
To exit the sequence, press the A-B button.
¡
To cancel Point A, press the
CLEAR/C.RESET button.
¡
This function does not work in the other repeat modes.
ALL
(entire disc repeat)
OFF
(repeat off)
¡
Repeat setting will be cleared when moving to another title, chapter, or track.
¡
Repeat playback are not available with all discs or during repeat A-B playback.
Random Playback
This shuffles the playing order of tracks instead of playback in the sequence.
DVD
STOP
MODE
RANDOM
CD-DA TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
PLAY x2 (Press twice)
PLAY
Note
¡
If you want to repeat the current track in the random selections, press the REPEAT button repeatedly until
“ TRACK’’ appears during playback. If you want to repeat the entire random selections, press the
REPEAT button repeatedly until
“ ALL’’ appears during playback.
PLAY or
CD-DA TOTAL 0:08:00
ENTER
ALL CLEAR
2/2
Up to 99 tracks can be stored.
Notes
¡
Press the CLEAR/C.RESET button at step [2] to erase the most recently entered program.
¡To erase all tracks in the program at once, select “ALL CLEAR’’ and press the ENTER button at step [2].
¡While a program is being played back, the STOP button works as follows;
⇒Press the STOP button and the
PLAY button next, so that the programmed playback restarts. (CD playback restarts from the current point.)
⇒Press the STOP button twice and the PLAY button next, so that playback restarts from the first track in the original order. However, your programmed playback can be restarted when you follow the above steps. (Your program is still stored until either the disc tray is open or power is turned off.)
¡To repeat the current track in the program, press the REPEAT button repeatedly until “ TRACK’’ appears during playback.
¡To repeat the entire program press the
REPEAT button repeatedly until “ ALL’’ appears during playback.
– 18 –
EN
Special Settings
Subtitle Language
DVD
Audio Language
DVD
This unit allows you to select a subtitle language (if available) during DVD playback.
This unit allows you to select an audio language (if multiple languages are available) during DVD playback.
Stereo Sound mode
DVD
This unit allows you to select a sound mode during CD playback.
PLAY
PLAY
PLAY
1.ENG/6
STEREO
1.ENG Dolby D 3/2.1ch 48k / 3
AUDIO
AUDIO
SUBTITLE
T-SET
Each time you press the SUBTITLE/T-
SET button, subtitle languages change.
For example
PLAY
SUBTITLE
T-SET
ENG
FRE
OFF
(English subtitles)
(French subtitles)
(no subtitles)
To set subtitle ON/OFF
1.ENG/6
OFF
Each time you press the AUDIO button;
For example
ENG
(English audio)
Each time you press the AUDIO button;
STEREO
L-CH
(right and left channels are active)
(left channel is active)
SPA
(Spanish audio)
FRE
Camera Angle
(French audio)
R-CH
(right channel is active)
Note
¡If the Virtual Surround setting is “1’’ or
“2’’, the sound mode will be fixed to
STEREO, and can not be changed.
DVD
Virtual Surround
Some DVD discs may contain scenes which have been shot simultaneously from various angles. You can change the camera angle if the ( ) icon appears on the screen. If the “ANGLE
ICON” setting is “OFF” in the Display menu, the ( ) icon will not appear.
(Refer to pages 20-21.)
You can enjoy surround-sound effect over two speakers of your own.
PLAY
DVD
OFF
V.SURR.
PLAY
1 / 8
Notes
¡If your language is not shown after pressing the AUDIO or SUBTITLE/T-
SET button several times, the disc may not have that language. However, some discs allow audio language or subtitle language setting on the disc menu. (Operation varies depending on the discs, so refer to the manual along with the disc.)
¡When “NOT AVAILABLE” appears on the TV screen, it means no subtitle is recorded on the scene.
¡If you choose a language that has a 3 letter language code, the code will be displayed every time you change the subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead. (Refer to page 24.)
ANGLE
Black Level Setting
DVD
Adjust the Black Level Setting to make the dark areas of the TV picture brighter.
PLAY
MODE
ON
1
1: Natural effect
2: Emphasized effect
OFF: No effects (original sound)
RETURN
Note (for CD play back only)
¡Virtual Surround will not be effective if the sound mode is set to something other than STEREO.
OFF
ON: Makes the dark areas brighter.
OFF: Shows the original picture as recorded.
RETURN
– 19 –
EN
DVD
DVD Set Up
Q UICK SETUP Men u
You can select the “PLAYER MENU”, “TV ASPECT”, or “DOLBY DIGITAL” from the QUICK SETUP menu quickly.
or
SETUP
STOP
Select the desired item
<SETUP MENU>
Confirm that QUICK is selected
SETUP
SETUP QUICK
QUICK
CUSTOM
INITIALIZE
PLAYER MENU
TV ASPECT
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
ON
•Refer to the sections “PLAYER
MENU”, “TV ASPECT”, or “DOLBY
DIGITAL” section on page 20 or 21.
CUST OM Men u
You can change the DVD player’s settings.
SETUP
STOP
<SETUP MENU>
SETUP
QUICK
CUSTOM
INITIALIZE or
Select CUSTOM
SETUP
QUICK
CUSTOM
INITIALIZE or to decide
To select the desired item
SETUP CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
LANGUAGE menu
SETUP LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ORIGINAL
OFF
ENGLISH
ENGLISH
DISPLAY menu
SETUP DISPLAY
TV ASPECT
STILL MODE
ANGLE ICON
AUTO POWER OFF
4:3 LETTER BOX
AUTO
ON
ON
AUDIO menu
SETUP AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
ON page 20
A
page 21
B
A
LANGUAGE Setting
Follow the step 1) to 3) in the “CUSTOM Menu” section above.
Select the desired item or page 21
C
Select the desired language or
LANGUAGE menu
SETUP
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
LANGUAGE
ORIGINAL
OFF
ENGLISH
ENGLISH
AUDIO ∗∗1 ∗∗2
(Default: ORIGINAL)
Sets the audio language.
SUBTITLE: ∗∗1 ∗∗2
(Default: OFF)
Sets the subtitle language.
DISC MENU: ∗∗1
(Default: ENGLISH)
Sets the language for DVD menu.
PLAYER MENU:
QUICK
(Default: ENGLISH)
Sets the language for the
On-screen display.
AUDIO
ORIGINAL
ENGLISH
FRENCH
SUBTITLE
OFF
ENGLISH
FRENCH
DISC MENU
ENGLISH
FRENCH
SPANISH
PLAYER MENU
ENGLISH
FRANÇAIS
ESPAÑOL
– 20 –
PARENTAL menu
SETUP
PASSWORD
PARENTAL
Please enter a 4-digit password.
page 22
D
6
To exit the menu
SETUP
∗1
• Language options are not available with some discs.
• If OTHER is selected on the AUDIO, SUBTI-
TLE or DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list on page 24.)
• Only the languages supported by the disc can be selected.
∗2
• Language Setting for Audio and Subtitle is not available with some discs. Then use the
AUDIO and the SUBTITLE/T-SET button.
Details are on page 19.
EN
B
DISPLAY Setting
You can change the display functions. Follow the step 1) to 3) in the “CUSTOM Menu” section on page 20.
Select the desired item or
6
To exit the menu
SETUP
TV ASPECT:
QUICK
(Default: 4:3 LETTER BOX)
See Hint to the right.
TV ASPECT 4:3 LETTER BOX
STILL MODE AUTO
ANGLE ICON ON
AUTO POWER OFF ON
TV ASPECT
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
Select the desired setting or
DISPLAY menu
SETUP DISPLAY
TV ASPECT
STILL MODE
ANGLE ICON
AUTO POWER OFF
4:3 LETTER BOX
AUTO
ON
ON
STILL MODE:
(Default: AUTO)
See Hint to the right.
TV ASPECT 4:3 LETTER BOX
STILL MODE AUTO
ANGLE ICON ON
AUTO POWER OFF ON
STILL MODE
AUTO
FIELD
FRAME
Select the desired setting or
ANGLE ICON:
(Default: ON)
Set to “ON” to show the angle icon when multiple camera angles are available during DVD playback.
TV ASPECT 4:3 LETTER BOX
STILL MODE AUTO
ANGLE ICON ON
AUTO POWER OFF ON
4:3 LETTER BOX
AUTO
OFF
ON
TV ASPECT:
• Select “4:3 LETTER BOX”, so that black bars appear on the top and bottom of the screen.
• Select “4:3 PAN & SCAN” for a full height picture with both sides trimmed.
• Select “16:9 WIDE” if a widescreen TV is connected to this unit.
STILL MODE:
• Select “AUTO” usually.
• If you select “FIELD”, the picture in the still mode will be stabilized.
• If you select “FRAME”, the picture in the still mode will be highly defined.
AUTO POWER OFF:
(Default: ON)
Set to “ON” to turn this unit off automatically after
35 minutes of no use.
TV ASPECT 4:3 LETTER BOX
STILL MODE AUTO
ANGLE ICON ON
AUTO POWER OFF ON
4:3 LETTER BOX
AUTO
ON
OFF
C
AUDIO Setting
Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow the step 1) to 3) in the “CUSTOM Menu” section on page 20.
Select the desired item or
6
To exit the menu
SETUP
DRC (Dynamic Range Control):
(Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL ON
OFF
ON
ON
AUDIO menu
SETUP AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
ON
DOWN SAMPLING:
(Default: ON)
Set to “ON” when outputting in 48 kHz.
Set to “OFF” when outputting the original sound.
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL ON
ON
OFF
ON
DRC:
• This function is available only on the discs which are recorded in the Dolby Digital format.
DOWN SAMPLING:
• When playing disc with copyright Protection, the sound will be down sampled at 48kHz, even if you set to OFF.
• This function is available only on digital outputting of a disc recorded in 96kHz.
DOLBY DIGITAL:
(Default: ON)
QUICK
Set to “ON” when the unit is connected to a Dolby Digital receiver.
• ON: Outputs a Dolby Digital Signals
• OFF: Convert the Dolby Digital into PCM (2 channel)
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL ON
ON
ON
OFF
– 21 –
EN
D
PARENTAL Setting
Parental Control limits the disc viewing that exceed your settings. (an incorrect password will not play.)
This feature prevents your children from viewing inappropriate materials.
P arental Le vels
Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set.
Follow the steps 1) to 3) in the “CUSTOM Menu” section on page 20.
Select “PARENTAL
LEVEL”
Select the desired levels
To exit the menu
Enter your desired fourdigit password (except for 4737)
1 2 3
4 5 6
7 8
0
9 or
ALL or
SETUP
PARENTAL LEVEL
CHANGE
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
PARENTAL menu
SETUP PARENTAL
PASSWORD
Please enter a 4-digit password.
or
If you have set a password already, enter the current four-digit password.
SETUP PARENTAL
PASSWORD
Enter current password.
CONTROL LEVELS
• ALL:
• Level 8:
• Levels 7 to 2:
• Level 1:
All parental locks are cancelled.
DVD softwares of any grades (adult/general/children) can be played back.
Only DVD softwares intended for general use and children can be played back.
Only DVD softwares intended for children can be played back, with those intended for adult and general use prohibited.
T o Chang e the P ass w or d f or P arental Contr ols
You can change your password for parental controls. Follow the steps 1) to 3) in the “CUSTOM Menu” section on page 20.
Enter your desired fourdigit password (except for 4737)
1
4
7
2
5
8
0
3
6
9
Select “CHANGE” or
PARENTAL LEVEL
CHANGE
ALL
Enter your new four-digit password
(except for 4737)
1
4
7
2
5
8
0
3
6
9
To exit the menu
SETUP
PARENTAL menu
SETUP PARENTAL
PASSWORD
Enter current password.
– 22 –
SETUP PARENTAL
PASSWORD
Please enter a 4-digit password.
• Record the password in case you forget it.
• If you forget the password, press 4, 7, 3, 7 at step 4, then enter your new password.
• Password will be cleared and parental levels will be set to ALL.
To return the All Selections of SET UP (except for PARENTAL) to the Default Setting
or
To exit the menu or
SETUP
STOP
SETUP
Select INITIALIZE
Select “YES”
<SETUP MENU>
SETUP
QUICK
CUSTOM
INITIALIZE
SETUP
QUICK
CUSTOM
INITIALIZE
SETUP INITIALIZE
Initialize?
NO
YES x2
(twice)
• When you cancel to initialize at step
3,select “NO”.
EN
Information
Troubleshooting Guide
If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.
PROBLEM CORRECTIVE ACTION
D
V
D
V
C
R
V
C
R
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
This unit does not respond to • Check if the power plug is connected to an AC outlet.
the remote control.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote.
• You have to be within 23 feet of this unit.
• Check if the right mode is selected. If it’s not in the right mode, press the DVD or
VCR buttons, whichever you need, on the remote control.
• Check if a cassette tape is in this unit.
• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then. If you hear some signal sound from the radio in response to your pressing buttons on the remote, the remote control is working.
Timer recording is impossible.
• Make sure the timer recording is set correctly.
• Make sure the TIMER REC light appears on the DVD/VCR. If not, press the SUBTI-
TLE/T-SET button.
• Make sure the VCR clock is set correctly.
Cannot go into Record mode.
• Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Activate this unit in VCR mode. Press the VCR button on the remote control so that the green VCR OUTPUT light is lit.
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing the CHANNEL (K /L) buttons on the DVD/VCR or the SKIP/CH.(K /L) buttons on the remote control.
Cannot view a tape but the audio is OK.
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the VCR is not in the Menu mode.
No, or poor, playback picture.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen • Re-check the ANT. IN and ANT. OUT connections. See the front page and page 6.
normally.
• Press the VCR/TV button.
• Press the VCR button on the remote control to activate it in the VCR mode. Check if the green
VCR OUTPUT light is lit. Then, set it to the TV position by pressing the VCR/TV button.
Video or color fades in and out when • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
making a copy of a video tape.
D
V
D
Cannot remove the tape.
No picture.
Disc cannot be played.
• Check if this unit is in the VCR mode. If not, press the VCR button on the remote control to switch the mode.
• Connect the video cables firmly.
• Insert a correct video disc that plays on this unit.
• Press the DVD button on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features.
• Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface.
No sound.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This unit does not support DTS audio. This is not a malfunction.
No DTS audio is output.
Distorted picture.
• Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language does not match the set up.
• The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction.
The camera angle cannot be • The DVD does not contain sequences recorded from different camera angles.
changed.
This is not a malfunction.
Audio or subtitle language cannot be changed.
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by this unit or the disc.
screen, prohibiting an operation This is not a malfunction.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
– 23 –
EN
Specifications
Video Heads :
Four Heads
Output signal format :
NTSC color
Power source :
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption :
21 W (standby: 3.6W)
Language List
Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
Operating temperature :
41°F (5°C) to 104°F (40°C)
Dimensions :
W : 17 3/16”(435mm)
H : 3 3/4” (94mm)
D : 9 3/16” (233mm)
Weight :
Approx 6lbs (2.7kg)
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
Code Language
5261
5256
5255
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
L-N
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Code Language
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5861
5847
5868
5860
5866
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will be
English.
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
Code Language
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
Code
6565
6557
6558
6561
5165
6567
6569
6568
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 19. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)
Limited Warranty
FUNAI CORP. will repair this Emerson product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
LABOR:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PUR-
CHASER. A PURCHASE RECEIPT OR OTHER PROOF OF ORIGINAL
RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PROD-
UCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This Emerson Limited warranty does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC
PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO
EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUEN-
TIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF
OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE
IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF
ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WAR-
RANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED
BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED
BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS
VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SER-
VICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU
MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF, AT
ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO
OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE
CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF
THIS PRODUCT WITHOUT PRIOR NOTICE.
To locate your nearest Emerson Authorized Service Center or for general service procedure, please call 1-800-256-2487 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-256-2487 http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
– 24 –
EN
1
Conexiones
Consulte la "Conexión básica del televisor" en la página delantera antes de utilizar esta unidad.
Canal de salida RF
Si el canal 3 se está utilizando para una transmisión.
1)Programe su televisor al canal 4.
2)Inserte una cinta pregrabada en esta unidad.
3)Pulse el botón OUTPUT en el
DVD/VCR para que se encienda la luz VCR OUTPUT.
• Si aparecen ruidos en la pantalla del televisor,pulse el botón VCR/TV en el mando a distancia.
4)Pulse una vez el botón PLAY.
5)Después de unos segundos, pulse el botón PLAY en el DVD/VCR durante
3 segundos.
• El canal de salida RF cambiará del canal 3 al canal 4 y podrá ver una imagen reproducida.
• Cuando no aparezca una imagen en la pantalla del televisor, repita el paso (4).
6)Pulse el botón STOP para parar la reproducción.
1
2
Instalación de las pilas del mando a distancia
2 3
3
Conmutación VCR/DVD
CHANNEL
OPEN/CLOSE
VCR
OUTPUT
DVD DISC IN
SKIP/REV STOP PLAY FWD/SKIP
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
VIDEO AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR
VCR
OUTPUT
DVD
Botón VCR
Botón DVD
SKI
Luz
DVD OUTPUT
Botón OUTPUT
1
4
7
DISPLAY
8
0
VCR
2
5
3
6
SKIP/CH.
VCR/TV
9
+10
DVD
SLOW
PAUSE
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
ENTER
RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
SUBTITLE
T-SET
ANGLE REPEAT A-B
Luz
VCR OUTPUT
4
POWER
Mando a distancia Pantalla del televisor o
Español
Activación de la unidad por primera vez
VCR
Encienda el televisor y sintonice al canal 3.
• Si el canal 3 se está utilizando para una transmisión, vea la sección "RF Output Channel".
SELEC. IDIOMA
ENGLISH
FRANCAIS
B ESPAÑOL [ON]
AJUSTE AUTO
CA 01
Conecta el cable de la caja de canales de cable o la caja de satélite en la toma ANT IN de DVD/VCR?
SI
Si
Pulse el botón
MENU para salir.
NO
No
Espere unos minutos.
Después del escaneo
• El sintonizador se detiene en el canal memorizado más abajo.
• Puede seleccionar sólo los canales memorizados en esta unidad con los botones
CHANNEL.
MODO VCR
Pulse el botón VCR en el mando a distancia.
(Compruebe que está encendida la luz
VCR OUTPUT.)
MODO DVD
Pulse el botón DVD en el mando a distancia
(Compruebe que está encendida la luz
DVD OUTPUT.)
Nota
• Si pulsa sólo el botón OUTPUT en el panel frontal NO conmuta el modo del mando a distancia. DEBE seleccionar también el modo correcto en el mando a distancia.
5
Ajuste del reloj
VCR
MENU o o o o o o o
-MENU-
PROGRAMAR
AUTOREPETIR [OFF]
AJUSTE CANAL
B
AJUSTE DE RELOJ
SELEC. IDIOMA
• Si no se ha ajustado el reloj, aparece la pantalla AJUSTE
DE RELOJ cuando pulse el botón MENU. En este caso, vaya al paso (2).
AJUSTE DE RELOJ
MES DIA
0 3 / – –
AÑO
– – – –
HORA MINUTO AM/PM
– – : – – – –
Seleccione el mes actual
AJUSTE DE RELOJ
MES DIA
0 3 / 1 5
AÑO
– – – –
HORA MINUTO AM/PM
– – : – – – –
Seleccione el día actual
AJUSTE DE RELOJ
MES DIA
0 3 / 1 5
AÑO
2 0 0 4
HORA MINUTO AM/PM
– – : – – – –
Seleccione el año actual
AJUSTE DE RELOJ
MES DIA AÑO
0 3 / 1 5 LUN 2 0 0 4
HORA MINUTO AM/PM
0 5 : – – – –
Seleccione la hora actual
AJUSTE DE RELOJ
MES DIA AÑO
0 3 / 1 5 LUN 2 0 0 4
HORA MINUTO AM/PM
0 5 : 4 0 – –
Seleccione los minutos actuales
AJUSTE DE RELOJ
MES DIA AÑO
0 3 / 1 5 LUN 2 0 0 4
HORA MINUTO AM/PM
0 5 : 4 0 P M AM
B
PM
Seleccione "AM" o "PM".
8
Para salir de la pantalla AJUSTE DE
RELOJ.
– 25 –
ES
Español
6
Reproducción de la grabadora de vídeo
Antes: Encienda el televisor y cambie al canal 3.
• Si el canal 3 se está utilizando para una transmisión, vea la sección "RF Output Channel".
7
Reproducción de DVD/CD
Antes: Encienda el televisor, amplificador y otros equipos que puedan estar conectados a esta unidad. Asegúrese que el televisor y el sintoamplificador de audio (de venta en los comercios) están en el canal correcto.
DVD
VCR
STOP
PARAR
Mando a distancia Pantalla del televisor
PLAY
REPRODUCIR B
OPEN/CLOSE
/EJECT
EXPULSAR
A
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1 2
4
7
5
8
DISPLAY
0
VCR
3
6
9
+10
DVD
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
POWER
OPEN/CLOSE
/EJECT
Mando a distancia Pantalla del televisor
PLAY
OPEN/CLOSE
/EJECT
STOP
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7 8
DISPLAY
0
VCR
2
5
9
+10
DVD
3
6
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
8
Mando a distancia
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7
DISPLAY
8
0
VCR
2
5
9
+10
DVD
3
6
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
ENTER
RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
SUBTITLE
T-SET
ANGLE REPEAT A-B
Modo DVD
Modo de grabadora de vídeo
Botón
Disco/cinta
(Orden alfabético)
1 2 3
4 5 6
7 8
0
9
+10
• Para seleccionar directamente el capítulo o el título.
• Para seleccionar directamente la canción.
• Para seleccionar el canal.
• El botón +10 no tiene efecto en el modo de grabadora de vídeo.
• Para buscar en avance/retroceso en un disco.
• Para empezar la reproducción en avance/ retroceso lento durante el modo de pausa.
• Para buscar en avance/
retroceso en un disco.
• Para el avance/retroceso
de una cinta.
ENTER
• Para mover el cursor y
determinar su posición.
• Para mover el curso y
determinar su posición.
en el menú de la grabadora
de vídeo.
• Para avanzar al siguiente
menú de la grabadora de
vídeo.
• Para volver un paso
durante el ajuste del reloj y
temporizador.
A-B
ANGLE
AUDIO
• Para repetir entre los puntos
A y B elegidos
• Para repetir entre los puntos A
y B elegidos.
• Para seleccionar los ángulos
de la cámara en un disco.
• Para seleccionar el idioma de
audio en un disco.
• Para seleccionar ESTÉREO,
L-CH o R-CH.
DISPLAY
DVD
MENU
MODE
• Para borrar los marcadores.
• Para borrar los números
entrados incorrectamente.
• Para indicar el modo de
disco actual.
• Para seleccionar el modo
de salida de DVD.
• Para activar el mando a
distancia en el modo DVD.
• Para llamar el menu en un
disco.
• Para activar/desactivar el
nivel del negro.
• Para borrar los marcadores.
• Para retirar el Nº de estado
en la entrada de programa.
• Para borrar los números
entrados incorrectamente.
• Para indicar el modo de
disco actual.
• Para seleccionar el modo de
salida de DVD
• Para activar el mando a
distancia en el modo DVD
• Para salir del menú de la
grabadora de vídeo.
•
Para reponer el contador de
cinta.
• Para indicar la hora actual,
contador de cinta y canal.
•
Para llamar el menú de la
grabadora de vídeo.
• Para disponer el orden de
reproducción o la
reproducción aleatoria.
OPEN/CLOSE
/EJECT
PAUSE
PLAY
POWER
• Para abrir o cerrar la bandeja
del disco.
• Para hacer una pausa de
reproducción del disco.
• Para avanzar la reproducción
un cuadro a la vez.
• Para empezar la reproducción
del disco.
• Para abrir o cerrar la bandeja
del disco.
• Para hacer una pausa en la
reproducción del disco.
• Para empezar la reproducción
del disco.
• Para expulsar el videocasete
de la grabadora de vídeo.
• Para hacer una pausa de la
reproducción o grabación de la cinta.
• Para avanzar la reproducción
un cuadro a la vez.
• Para empezar la reproducción
de la cinta.
• Para activar o desactivar la
unidad.
• Para activar o desactivar la
unidad.
• Para activar o desactivar la
unidad.
REC/OTR
• Para empezar una grabaciòn.
REPEAT
RETURN
SEARCH
MODE
SETUP
• Para reproducir repetidamente
un capítulo o título.
• Para reproducir repetidamente una
canción o disco.
• Para volver a la operación
previa en el menú de
programación de DVD.
• Para buscar un capítulo, título u hora.
• Para volver rápidamente a un
lugar o disco.
• Buscar los marcadores.
• Para volver a la operación
previa en el menú de
programación de DVD.
• Para buscar una canción.
• Para buscar la hora.
• Para volver rápidamente a un lugar
o disco.
• Buscar los marcadores.
• Para llamar el menú de
programación de DVD.
• Para llamar el menú de
programación de DVD.
• Para llamar el menú de
búsqueda de índice u hora.
SKIP/CH.
SLOW
SPEED
STOP
SKIP/CH.
• Para saltar capítulos
• Para parar la grabación.
• Para seleccionar subtítulos
en un disco.
• Para saltar canciones.
• Para parar la grabación.
• Para cambiar de canal.
• Para ajustar manualmente el
seguimiento durante la reproducción.
• Para ver la cinta en cámara
lenta.
• Para seleccionar la velocidad
de grabación.
• Para parar la reproducción o
grabación.
• Para poner la grabadora de
vídeo en el modo de espera
para una grabación con temporizador.
TOP MENU
• Para llamar el menú superior
en un disco.
VCR
VCR/TV
V.SURR.
• Para seleccionar la posición
de DVD o posición del televisor.
• Para activar/desactivar el
envolvente virtual.
• Para seleccionar la posición de
CD o la posición del televisor.
• Para activar/desactivar el
envolvente virtual.
• Para seleccionar el modo de
salida de la grabadora de vídeo.
• Para activar el mando a distancia
en el modo de la grabadora de vídeo.
• Para seleccionar la posición de la
grabadora de vídeo o posición del televisor.
– 26 –
ES
1
Connections
Please refer to “Basic TV
Connection” on the front page before you use this unit.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1)Set your TV to channel 4.
2)Insert a pre-recorded tape into this unit.
3)Press the OUTPUT button on the
DVD/VCR so that the VCR OUTPUT light is lit.
• If noise appears on the TV screen, press the VCR/TV button on the remote control.
4)Press the PLAY button once.
5)After a few seconds, press the PLAY button on the DVD/VCR for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.
• When a picture does not appear on the TV screen, repeat step [4].
6)Press the STOP button to stop playback.
1
2
Installing the Batteries for the Remote Control
2
3
4
Quick Use Guide
Turn on the unit for the first time
VCR
Turn on the TV and set it to channel 3.
• If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.
POWER
Remote Control TV Screen or
LANGUAGE SELECT
[ON]
B
ENGLISH
FRANCAIS
ESPAÑOL
AUTO SET UP
CH 01
3
VCR/DVD Switching
OPEN/CLOSE
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
VIDEO AUDIO
POWER REW F.FWD
STOP/EJECT PLAY
TIMER REC
REC /OTR
CHANNEL
VCR
OUTPUT
DVD
VCR OUTPUT DVD DISC IN
SKIP/REV STOP PLAY FWD/SKIP
VCR button
DVD button
1
4
7
DISPLAY
0
VCR
2
5
8
3
SKIP/CH.
6
9
VCR/TV
SLOW
+10
DVD PAUSE
SKI
DVD OUTPUT light
OUTPUT button
PLAY
STOP
REC/OTR
MENU ENTER
SETUP TOP MENU RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
SUBTITLE
T-SET
ANGLE REPEAT A-B
VCR OUTPUT light
Do you connect the cable from the cable box or the satellite box to the DVD/VCR’s ANT IN jack?
YES
Y es
Press the MENU button to exit
NO
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using the CHANNEL buttons.
5
Clock Set Up
VCR
MENU
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B
CLOCK SET
LANGUAGE SELECT or or or or or
• If the clock is not set, the
CLOCK SET screen appears when you press the MENU button. In this case, go to step [2].
CLOCK SET
MONTH DAY
0 3 / – –
YEAR
– – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
CLOCK SET
MONTH DAY
0 3 / 1 5
YEAR
– – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current day
CLOCK SET
MONTH DAY
0 3 / 1 5
YEAR
2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
Select the current year
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : – – – –
Select the current hour or
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 – –
Select the current minute
VCR MODE
Press the VCR button on the remote control.
(Verify that the VCR OUTPUT light is lit.)
DVD MODE
Press the DVD button on the remote control.
(Verify that the DVD OUTPUT light is lit.)
Note
• Pressing only the OUTPUT button on the front panel DOES NOT switch the mode of the remote control. You
MUST select the correct mode on the remote control.
or
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 MON 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B
PM
Select “AM” or “PM”
8
To exit the CLOCK SET screen.
– 27 –
EN
Quick Use Guide
6
VCR Playback
Before: Turn on the TV and set it to channel 3.
• If channel 3 is already occupied for broadcasting, see “RF
Output Channel” section.
7
DVD/CD Playback
Before: Turn on the TV, amplifier and any other components which are connected to this unit. Make sure the TV and audio receiver (commercially available) are set to the correct channel.
DVD
VCR
STOP
STOP
Remote Control TV Screen
PLAY
PLAYB
OPEN/CLOSE
/EJECT
EJECT A
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7 8
DISPLAY
0
VCR
2
5
9
+10
DVD
3
6
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
POWER
STOP
OPEN/CLOSE
/EJECT
OPEN/CLOSE
/EJECT
Remote Control TV Screen
PLAY
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7
DISPLAY
8
0
VCR
2
5
9
+10
DVD
3
6
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
8
Remote Control
POWER
SPEED AUDIO
OPEN/CLOSE
/EJECT
1
4
7
DISPLAY
8
0
VCR
2
5
3
6
9
+10
DVD
SKIP/CH.
VCR/TV
SLOW
PAUSE
PLAY
STOP
REC/OTR
MENU ENTER
SETUP TOP MENU RETURN
MODE V.SURR.
SEARCH
MODE
CLEAR/
C. RESET
SUBTITLE
T-SET
ANGLE REPEAT A-B
Printed in China
DVD mode VCR mode
Button
Disc/Tape
(Alphabetical order)
1 2 3
4
7
5
8
0
6
9
+10
ENTER
A-B
ANGLE
AUDIO
CLEAR/
C. RESET
DISPLAY
DVD
MENU
MODE
• To select chapter or title directly.
• To select track directly.
• To select channel.
• The +10 button has no effect in VCR mode.
• To search forward/backward through a disc.
• To begin slow forward/reverse playback during the pause mode.
• To search forward/backward through a disc.
• To forward/backward a tape.
• To move the cursor and determine its position.
• To move the cursor and determine its position.
• To select an item
on the VCR Menu.
• To advance to the next
VCR Menu.
• To go back one step during
clock and timer setting.
• To repeat between your chosen point A and B.
• To select camera angles on a disc.
• To repeat between your chosen point A and B.
• To select audio languages on a disc.
• To select STEREO,
L-CH or R-CH.
• To clear the markers.
• To clear the numbers entered incorrectly.
• To clear the markers.
• To remove status No. in program input.
• To clear the numbers entered incorrectly.
• To display the current disc mode.
• To display the current disc mode.
• To select the DVD output
mode.
• To activate the remote control
in DVD mode.
• To select the DVD output
mode.
• To activate the remote control
in DVD mode.
• To exit the VCR Menu.
• To reset the tape counter.
• To display the current time,
tape counter, and channel.
• To call up the Menu
on a disc.
• To call up the VCR Menu.
• To set black level on/off.
• To arrange the playing order or play randomly.
OPEN/CLOSE
/EJECT
PAUSE
• To open or close the disc tray.
• To pause disc playback.
• To advance playback one frame at a time.
• To begin disc playback.
• To open or close the disc tray.
• To pause disc playback.
• To begin disc playback.
• To eject the video cassette from the VCR.
• To pause tape playback or recording.
• To advance playback one frame at a time.
• To begin tape playback.
PLAY
POWER
• To turn the unit on or off.
• To turn the unit on or off.
• To turn the unit on or off.
REC/OTR
• To start a recording.
REPEAT
RETURN
SETUP
SKIP/CH.
SLOW
SPEED
SKIP/CH.
• To play a chapter or title repeatedly.
• To play a track or disc repeatedly.
• To return to the previous operation on the DVD setup menu.
• To search chapter, title or time.
• To rapidly return to a location of disc.
• Search the markers.
• To return to the previous operation on the DVD setup menu.
• To search track.
• To search time.
• To rapidly return to a location of disc.
• Search the markers.
• To call up the DVD setup
menu.
• To call up the DVD setup
menu.
• To call up the index or time
search menu.
• To skip chapters.
• To skip tracks.
• To change channels.
• To adjust the tracking manually
during playback.
• To view the tape in slow motion.
• To select the recording speed.
STOP
SUBTITLE
T-SET
TOP MENU
VCR
VCR/TV
V.SURR.
• To stop playback.
• To stop playback.
• To stop playback or recording.
• To select subtitles on a disc.
• To put the VCR into standby mode for a timer recording.
• To call up the Top Menu on a disc.
• To select DVD position or
TV position.
• To select CD position or TV position.
• To set virtual surround on/off. • To set virtual surround on/off.
• To select the VCR output mode.
• To activate the remote control in VCR mode.
• To select VCR position or
TV position.
1VMN20189 / H9612UD
★★★★★
advertisement
Related manuals
advertisement