L6118UU.QX33 02.3.23 1:03 PM Page 1

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS:

LABOR:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any the product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FIT-

NESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTA-

TIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY FUNAI AUTHORIZED SER-

VICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED

SERVICE FACILITY.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT.

IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS

COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT

VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO

OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest Emerson Authorized Service Center or general service procedure, please call 1-800-256-2487 or write to the following:

FUNAI CORPORATION, INC.

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-256-2487

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

0EMN01978

Owner’s

Manual

FEATURES

COLOR TELEVISION

EWT19S2 (19 inch)

STEREO

“EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS

OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.”

●

●

●

Tinted, Bright Black Matrix Picture Tube

181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic tuning system provides free and easy channel selection, and lets you tune directly to any channel

●

●

●

● using the channel number buttons (0~9 and +100-key) on the remote control.

On-Screen Function Display.

Full-Function Remote Control

Sleep Timer

Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news,

● prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

Auto Shut Off Function- If there is no air signal input from the antenna terminal and no

● operation for 15 minutes, the TV will turn itself off automatically.

V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

PRECAUTION

Printed in Malaysia

L6118UU * * * * *

●

●

●

●

Place your TV in a room with adequate ventilation.

Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

Do not place your TV on soft surfaces, such as rugs or blankets.

Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

This Owner’s Manual is made of recycled paper.

IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING

AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE

1-800-256-2487

ANTENNA/CABLE CONNECTIONS

Before plugging the UHF/VHF Rod

Antenna into the ANT(enna). IN jack, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT(enna). IN jack.

Bent pin

Cable

Plug

(Needs to be straightened) (Straight pin)

UHF

Antenna

(Not supplied)

VHF

Antenna

(Not supplied)

VHF/UHF Combiner

(Not supplied)

OR

UHF/VHF Rod

Antenna

(Not supplied)

ANT.IN

ANT. IN

OR

* Some cable TV systems use scrambled signals and require a special converter to receive these channels.

Consult your local cable company.

CATV Box * or Satellite Box

(Not supplied)

OUT IN

75-ohm

Coaxial Cable

From Cable System or Satellite Antenna

75-ohm

Coaxial Cable

From Cable System

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

VHF/UHF

Combination Antenna

(Not supplied)

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.

Caption Mode

(1) Characters can be displayed on the TV screen when the received broadcast signal contains the

Caption Signals.

(2) Paint-on mode: Displays input characters on the screen immediately.

Pop-on mode: Once characters are stored in memory, it is displayed all at once.

Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)

Note: If the CAPTION C1 or C2 is selected but the caption signal is not included, characters will not be displayed.

Text Mode

(1) Displays the text on the screen by scrolling (max. 7 lines)

(2) If the received broadcast signal does not contain the caption or text signal, no change will occur.

Notes:

(1) When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a

VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or text.

(2) Captions and texts may not match the TV voice exactly.

(3) Interference may cause the closed caption system not to function properly.

(4) The caption or text characters will not be displayed while the menu display or function’s display is shown.

(5) If you see this screen :

If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].

L6118UU.QX33 02.3.23 1:03 PM Page 2

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-

ANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THIS SYMBOL INDICATES THAT DAN-

GEROUS VOLTAGE CONSTI-TUTING A

RISK OF ELECTRIC SHOCK IS PRE-

SENT WITHIN THIS UNIT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK) NO

USER SERVICEABLE PARTS INSIDE. REFER SER-

VICING TO QUALIFIED SERVICE PERSONNEL.

The important note is located on the rear of the cabinet.

THIS SYMBOL INDICATES THAT

THERE ARE IMPORTANT OPERATING

AND MAINTENANCE INSTRUCTIONS

IN THE LITERATURE ACCOMPANY-ING

THE APPLIANCE.

IMPORTANT SAFEGUARDS

1. Read instructions-All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions-The safety and operating instructions should be retained for future reference.

3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions-All operating and use instructions should be followed.

5. Cleaning-Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a

CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.

6. Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards.

7. Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV.

Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended by the

PORTABLE CART WARNING manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

S3126A

AMEUBLES- Cet appareil ne doit

être placé que sur un meuble (avec ou sans roulettes) recommandé par

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution.

S3126A Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.

9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to .

10. Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions.

11. Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the polarized plug.

12. Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

S 2 8 9 8 A

NEC - NATIONAL ELECTRICAL CODE receptacles, and the point where they exit from the appliance.

13. Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

(Fig. A)

14. Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system.

This will prevent damage to the TV due to lightning and power-line surges.

15. Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17. Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

18. Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. Damage Requiring Service-Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the TV.

c. If the TV has been exposed to rain or water.

d. If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.

e. If the TV has been dropped or damaged in any way.

f. When the TV exhibits a distinct change in performance-this indicates a need for service.

20. Replacement Parts-When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21. Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.

22. Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL -

CHANNEL POWER VIDEO L AUDIO R HEAD PHONE MENU VOLUME

- REAR PANEL -

ANT.IN

- REMOTE CONTROL -

7

9

1 2

1

4

7

POWER

2

5

8

0

GAME SLEEP

DISPLAY

3

6

9

+100

CHANNEL

RETURN

3 4

14

13

12

11

6

5

VOL

CH

CH

VOL

MUTE

10

MENU

4

1. VIDEO (in) jack- Connect to the video output jack of a video camera or VCR.

2. AUDIO (in) jacks- Connect to the audio output jack of a video camera or VCR.

3. HEAD PHONE jack

- To connect headphone (not supplied) for personal listening.

4. MENU button- Press to display the menu on the TV screen.

5. VOLUME

▲/▼ buttons- Press to control the volume level.

Press to determine a setting mode from the

5 6 7 8

16 menu on the TV screen. (only the VOL

▲ button)

Press to select or adjust from a particular menu. (for example: Language Selection,

Channel Presetting, Closed Caption Selection,

Picture Adjustment, V-CHIP Set Up)

6. CHANNEL

▲/▼ buttons- Press to select memorized channel.

NOTE:You MUST PRESET channels

BEFORE using CHANNEL

▲/▼ button.

(See CHANNEL PRESETTING)

Press to select a setting mode from the menu on the TV screen.

Press to select item you want to adjust in the picture control mode.

7. POWER button- Press to turn the TV ON and OFF.

8. Infrared Sensor Window- Receives the infrared control signals from the remote control unit.

9. CHANNEL NUMBER buttons- Press two digits to directly access the desired channel.

Remember to press a "0" before a single digit channel.

+100 button- Press to select cable channels which are equal or greater than number 100.

10.MUTE button- Press the MUTE button to turn off the sound portion of the TV program. (Volume level display turns LIGHT

RED from LIGHT BLUE.) Press the

MUTE button again or press the VOL(ume)

▲ or ▼ button to restore sound.

11.CHANNEL RETURN button- Press this button to go back to the previously viewed channel. For example, pressing the CHAN-

NEL RETURN button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3.

12.DISPLAY button- Press to display the channel number on the screen. If you press it again, the channel number will disappear.

13.SLEEP button- Press the SLEEP button to display the sleep timer and start the function. The shut off time can be determined by the number of times you press the button. (0, 10, 20, 30,..90, 0 minutes)

14.GAME button- Press to set the Game mode and external input mode at the same time. Press the GAME button again to exit the mode.

15.ANT(enna). IN jack- Connect to an antenna, cable system, or satellite system.

16.AC cord- Connect to a standard AC outlet

(120V/60Hz).

NOTE: Remove the AC cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.

15

INSTALLING THE BATTERIES

1

Slide the battery compartment cover on the remote unit.

2

Insert 2 "AA" penlight batteries into battery compartment in the direction as indicated by the polarity (+ / -) markings. Batteries installed with incorrect polarity may damage the remote unit.

3

Replace the cover.

L6118UU.QX33 02.3.23 1:03 PM Page 3

PREPARATION FOR USE

LANGUAGE SELECTION

If you want to change the language of the on-screen menu, follow the procedure below.

1) Connect the power cord to a standard AC outlet.

2) Press the POWER button to turn on the TV.

3) Press the MENU button so that the menu display appears on the TV screen.

4) Press the CH(annel)

▲ or ▼ button to point to "[ENGLISH]".

5) Select "ENGLISH" or "ESPAÑOL" = Spanish by using the VOL(ume)

▲ or ▼ button.

6) Press the MENU button to exit the menu.

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

CHANNEL PRESETTING

NOTE:You MUST PRESET channels BEFORE using CHANNEL

▲ or ▼ button.

To preset a channel or to change a preset channel, follow the procedure below.

1) Press the POWER button to turn on the TV.

2) Press the MENU button so that the menu display appears

●

● on the TV screen.

3) Press the CH(annel)

▲ or ▼ button to point to "CHANNEL SET".

Then, press the VOL(ume)

▲ button.

4) Press the CH(annel)

▲ or ▼ button to point to "AUTO MEMO".

Then, press the VOL(ume)

▲ button.

The tuner scans and memorizes all active channels in your area.

The TV distinguishes between standard TV channels and cable channels.

When AUTO MEMO action is completed, the lowest memorized channel

● reappears on the screen.

When you press the CH(annel)

▲ or ▼ button after selecting AUTO

MEMO, the tuner will stop at the memorized channels only.

● The TV may recognize TV channels to be CATV channels by the receiving conditions. In this case, try AUTO MEMO action again in the fine receiving conditions.

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

ADD/DELETE

AUTO MEMO

STEREO [OFF]

[ADD/DELETE FUNCTION]

1) Press the MENU button so that the menu display appears on the TV screen.

2) Press the CH(annel)

▲ or ▼ button to point to "CHANNEL SET".

Then, press the VOL(ume)

▲ button.

3) Press the VOL(ume)

▲ button so that "ADD/DELETE" is selected.

4) Use the CH(annel)

▲ or ▼ button to select the channel you wish to put into memory or to erase from memory.

Note: The display will return to the screen in about 10 seconds.

Perform "ADD/DELETE" function while this display appears on the

●

● screen.

Press the VOL(ume)

▲ or ▼ button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory.

Press the VOL(ume)

▲ or ▼ button to light up the channel number in LIGHT RED if you wish to erase the channel from memory.

5) Press the MENU button to exit the menu.

STEREO SOUND SYSTEM

This function is suppresses noise, restores the dynamic range and electronically expends the stereo signal to create a more specious sound effect.

1) Press the MENU button so that the menu display appears on the TV screen.

2) Press the CH(annel)

▲ or ▼ button to point to "CHANNEL SET".

Then, press the VOL(ume)

▲ button.

3) Press the CH(annel)

▲ or ▼ button so that "STEREO" is selected.

4) Press the VOL(ume)

▲ or ▼ button to select the stereo mode on or off.

Stereo sound is effective when the "STEREO" is on.

ADD/DELETE

AUTO MEMO

STEREO [OFF]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

ADD/DELETE

AUTO MEMO

STEREO [OFF]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

ADD/DELETE

AUTO MEMO

STEREO [ON]

RESUME FUNCTION

If the power fails or is disconnected while the TV is powered on, the TV will turn on automatically when the power resumes.

OPERATIONS

WATCHING A TV PROGRAM

1) Press the POWER button to turn on the TV.

2) Select the desired channel with the CH(annel)

▲ or ▼ button.

3) Adjust the volume to the desired listening level using the VOL(ume)

▲ or ▼ button.

4) Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)

SETTING THE SLEEP TIMER

The sleep timer function enables you to shut off the power without pressing the POWER button after a desired time period.

1) Press the POWER button to turn on the TV and press the SLEEP button on the remote control .

2) You may change the sleep time with pressing the SLEEP button on the remote control repeatedly. The timer is set up

SLEEP 10 to 90 minutes, 10 minutes each time the SLEEP button is pushed. (The timer display counts up and sleep timer will be displayed on the screen when you press the SLEEP button on remote control.)

To cancel the sleep timer:

Press the SLEEP button repeatedly until "SLEEP 0" is displayed.

Note: When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc.

with either a dialogue caption or text display added to the program.

: Press the VOL(ume)

▲ or ▼ button.

1) Press the MENU button so that the menu display appears on the TV screen.

2) Press the CH(annel)

▲ or ▼ button to point to "CAPTION".

3) Press the VOL(ume)

▲ or ▼ button to select the mode you wish.

4) When done, press the MENU button to exit the menu.

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [ C1]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [ C2]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [ T1]

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [ T2]

PICTURE ADJUSTMENT

1) Press the MENU button so that the menu display appears on the TV screen.

2) Press the VOL(ume)

▲ button so that "PICTURE" is selected.

3) Select the feature you wish to adjust with the CH(annel)

▲ or ▼ button and adjust it with the

VOL(ume)

▲ or ▼ button.

GAME MODE

Set to the most suitable position for TV

GAME.

● In the above steps, the picture adjustment display will disappear from the TV screen

[+] : ON

[ - ] : OFF

BRIGHT

Adjust until the whitest parts of the picture are as bright as you prefer.

[+] : increase brightness

[ - ] : decrease brightness after about 10 seconds unless you press any buttons, even though you may not be finished. Press the MENU and VOL(ume)

▲ button so that "PICTURE" is selected. Then, press the CH(annel)

▲ or ▼ button repeatedly until the display returns to the screen.

● If you adjust the other Picture control after you set the Game mode to [ON], the Game mode is set to [OFF] automatically.

CONTRAST

Adjust to increase or decrease contrast.

[+] : increase contrast

[USING THE GAME BUTTON]

You may also set the Game mode and external input mode at the same time by pressing the

[ - ] : decrease contrast

COLOR

Adjust to be brilliant or pale color.

[+] : be brilliant color

[ - ] : be pale color

GAME button on the remote control. “GAME” appears on the TV screen.

● To exit the Game mode and external input mode, press the GAME button on the remote

TINT

Adjust to obtain natural skin tones.

[+] : greenish tone

[ - ] : reddish tone

● control again.

To cancel the Game mode only, adjust the picture control. In this case, “VIDEO” instead

Notes:

● “+” is achieved by pressing the VOL(ume)

▲ button and “-” by pressing the VOL(ume)

▼button.

● of “GAME” appears on the TV screen.

When you press the GAME button if the TV is off, the TV turns on and will be in the

Game mode and external input mode automatically.

: Press the CH(annel)

▲ or ▼ button.

[-]

OFF

GAME MODE [+]

ON

[-] BRIGHT [+] [-] CONTRAST [+] [-] COLOR [+] [-] TINT [+]

L6118UU.QX33 02.3.23 1:03 PM Page 4

OPERATIONS (Continued)

V-CHIP SET UP

V-CHIP enables parents to prevent their children from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels, and Emergency Broadcast System signals), then denies access to programming if the program's rating meets the limitations you select. In this case, "PROTECTED

PROGRAM by ..." message appears on the TV screen.

To block ratings, follow the steps below.

● Programming may be rated by the Motion Picture Association of America (MPAA) or according to the Television Parental Guidelines. In order to block any inappropriate programming, set

● your limits in both places (MPAA RATING and TV RATING).

You cannot access the menu when the "PROTECTED PROGRAM by ..." message appears. In this case, change to the unblocked channel, then press the MENU button.

[MPAA RATING SET UP]

1

Press the MENU button so that the menu display appears on the TV screen.

2

Press the CH(annel)

▲ or ▼ button to point to "V-CHIP SET UP".

Then, press the VOL(ume)

▲ button.

3

Press the CH(annel)

▲ or ▼ button to point to "MPAA RATING".

Then, press the VOL(ume)

▲ button.

4

Press the CH(annel)

▲ or ▼ button to point to your desired item.

Then, press the VOL(ume)

▲ button to select [BLOCK] or [VIEW].

<Selection>

• G:

• PG:

• PG-13:

• R:

• NC-17:

• X:

<Rating Category Explanations>

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompanying parent or adult guardian

No one under 17 admitted

Mature audience only

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

TV RATING

MPAA RATING

G [VIEW]

PG [VIEW]

PG-13 [VIEW]

R [BLOCK]

NC-17 [BLOCK]

X [BLOCK]

●

●

●

When you select the rating category and turn it [BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn [VIEW] automatically.

When you turn "G" to [BLOCK] or [VIEW], the all ratings will turn to [BLOCK] or [VIEW] automatically.

When you turn "X" to [VIEW], the all ratings will turn to [VIEW] automatically.

5

Press the MENU button to exit the menu.

[TV RATING SET UP]

1

Press the MENU button so that the menu display appears on the TV screen.

2

Press the CH(annel)

▲ or ▼ button to point to "V-CHIP SET UP".

Then, press the VOL(ume)

▲ button.

3

Press the CH(annel)

▲ or ▼ button to point to "TV RATING".

Then, press the VOL(ume)

▲ button.

4

Press the CH(annel)

▲ or ▼ button to point to your desired item.

Then, press the VOL(ume)

▲ button to select [BLOCK] or [VIEW].

<Selection>

• TV-Y:

• TV-Y7:

• TV-G:

• TV-PG:

• TV-14:

• TV-MA:

<Rating Category Explanations>

Appropriate for all children

Appropriate for children seven and older

General Audience

Parental Guidance suggested.

Unsuitable for children under 14

Mature audience only

PICTURE

CHANNEL SET

[ENGLISH]ESPAÑOL

V-CHIP SET UP

CAPTION [OFF]

TV RATING

MPAA RATING

TV-Y [VIEW]

TV-Y7 ( ) [VIEW]

TV-G [VIEW]

TV-PG ( ) [VIEW]

TV-14 ( ) [VIEW]

TV-MA ( ) [VIEW]

●

●

●

When you select the rating category and turn it [BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn [VIEW] automatically.

When you turn "TV-Y" to [BLOCK] or [VIEW], the all ratings will turn to [BLOCK] or

[VIEW] automatically.

When you turn "TV-MA" to [VIEW], the all ratings will turn to [VIEW] automatically.

When you select TV-Y7, TV-PG, TV-14, or TV-MA and you press the VOL(ume)

▲ button, the sub-ratings will appear on the TV screen.

If you select the rating category (example: TV-PG) and turn it [BLOCK] or [VIEW], the sub-ratings (example: V for Violence) will turn [BLOCK] or [VIEW] automatically.

You can set the sub-ratings to [BLOCK] or [VIEW] individually when the rating category is set to [BLOCK]. To set the sub-ratings individually, follow

TV-Y7 [BLOCK] the steps below.

FV [BLOCK]

●

●

●

When you select [TV-Y7]:

Press the CH(annel)

▲ or ▼ button to select "FV" (Fantasy Violence).

Then, press the VOL(ume)

▲ button to select [BLOCK] or [VIEW].

When you select [TV-PG], [TV-14] or [TV-MA]:

Press the CH(annel)

▲ or ▼ button to select "D"(Suggestive Dialog),

"L"(Coarse Language), "S"(Sexual Situation), or "V"(Violence). Then, press the VOL(ume)

▲ button to select [BLOCK] or [VIEW].

Note: When you select [TV-MA], "D" does not appear on the TV screen.

The sub-ratings which set to [BLOCK] appears next to the rating category

5 in the TV RATING menu.

Press the MENU button to exit the menu.

TV-PG [BLOCK]

D [BLOCK]

L [BLOCK]

S [BLOCK]

V [BLOCK]

TV-Y [VIEW]

TV-Y7 ( ) [VIEW]

TV-G [BLOCK]

TV-PG (DLSV) [BLOCK]

TV-14 (DLSV) [BLOCK]

TV-MA ( LSV) [BLOCK]

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. Before arranging for service, check these items. It could save your time and money.

QUICK SERVICE CHECK LIST

POSSIBLE REMEDY

Try a new channel, if OK, then possible station trouble.

Is TV plugged in?

Power at outlet?

Is TV’s POWER button on?

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Turn off with POWER button and then turn it on after about a minute.

Adjust COLOR control.

Adjust CONTRAST & BRIGHT control.

Check batteries in Remote Control.

Closed Caption Problem

My TV is showing captions that are misspelled.

Possible Remedy

You are watching a live broadcast and spelling errors made by the closed captioning production company may pass through uncorrected. A prerecorded program will not show any misspelled words because of the normal time available for editing the captions.

My TV will not show the text in its entirety or there is a delay of what is being said.

Captions that are delayed a few seconds behind the actual dialogue are common for live broadcasts. Most captioning production companies can display a dialogue to a maximum of 220 words per minute.

If a dialogue exceeds that rate, selective editing is used to insure that the captions remain up-to-date with the current TV screen dialogue.

My captions are scrambled with white boxes on the TV screen.

Interference caused by building, power lines, thunderstorms, etc.

may cause scrambled or incomplete captions to appear.

My program guide listed a TV show as being closed captioned but none of the captions were displayed.

My prerecorded videotape does not show any captions. The tape box mentions it being closed captioned.

Broadcasters may at times use a time compression process to the actual program so that additional advertising time can be given.

Since the decoder cannot read the compressed information, captions will be lost.

The videotape was either an illegal copying or the tape duplicating company accidentally left out the captioning signals during the copying process.

My TV screen shows a black box on certain channels.

You are in the TEXT mode. Select CAPTION mode or CAPTION

[OFF].

MAINTENANCE

CABINET CLEANING

● Wipe the front panel and other exterior surfaces of the TV with a soft cloth immersed

● in lukewarm water and wrung dry.

Never use a solvent or alcohol. Do not spray insecticide liquid near the TV. Such chemicals may cause damage and discoloration to the exposed surfaces.

PICTURE TUBE CLEANING

Wipe the picture tube of the TV with a soft cloth. Before cleaning the picture tube, disconnect the power cord.

SPECIFICATIONS

GENERAL SPECIFICATIONS

Television system: NTSC-M TV Standard

Closed Caption

System:

Channel coverage

§15.119/FCC

VHF:

UHF:

CATV:

2 ~ 13

14 ~ 69

2 ~ 13, A ~ W,

W+1 ~ W+84,

Tuning System

Channel access:

A-5 ~ A-1, 5A

181 channel frequency synthesized tuning system

Direct access keyboard, programmable scan and up/down

Terminals

Antenna input:

Video input:

Audio input:

Head phone

Stereo Sound System

2 speakers

VHF/UHF/CATV

75 ohm unbalanced

(F-type)

RCA connector x 1

RCA connector x 2

(L+R)

1/8” stereo (3.5mm)

SUPPLIED

ACCESSORIES

Remote control unit

(N0158UD)

Batteries ("AA" x 2)

Owner’s Manual

ELECTRICAL SPECIFICATIONS

Sound output: 1W, 8 ohmx2

OTHER SPECIFICATIONS

Remote control: Digital encoded infrared light system

Operating temperature: 5°C to 40°C

(41°F~104°F)

Power requirements: AC120V, 60Hz

Power consumption

(Maximum):

Picture tube:

Dimensions:

Weight:

73W

19”

H : 16-3/4"(428mm)

W: 18-3/4"(475mm)

D : 18" (454mm)

37.5 lbs. (17kg)

•Designs and specifications are subject to change without notice.

•If there is a discrepancy between languages, the default language will be English.

As an E NERGY S TAR Partner, our company has determined that this product meets the E NERGY S TAR guidelines for energy efficiency. E NERGY S TAR is a U.S. registered mark.