Owner`s manual | Emerson LC320EM8 Flat Panel Television User Manual

TM
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
32 inch Digital / Analog
LCD TV
Owner’s Manual
LC320EM8
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
7
8
9
-
0
AUDIO
STILL
SCREEN
MODE
SETUP
ENTER
INFO
BACK
CH RETURN
VOL.
MUTE
CH
HIGH-DEFINITION TELEVISION
TO RECEIVE DIGITAL/ANALOG SIGNAL,
YOU MUST CONNECT ANTENNA.
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-256-2487, OR
VISIT OUR WEB SITE AT http://www.EmersonAudioVideo.com
© 2007 Funai Electric Co., Ltd.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT WITHIN
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELEC-
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
TRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The important note is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions should
be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss of an
authorization code for a CATV converter, is not intended to be
unplugged by the user for cleaning or any other purpose, may exclude
the reference to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by the
TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold
with the TV.
PORTABLE CART WARNING
Any mounting of the appliance should follow
the manufacturer’s instructions and should use
a mounting accessory recommended by the
manufacturer. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination to
S3126A
overturn.
AMEUBLES - Cet appareil ne doit être placé SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
que sur un meuble (avec ou sans roulettes)
APPAREIL ET MEUBLE A ROULETTES
recommandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez
les deux ensembles avec précaution. Un arrêt
brusque, l’utilisation d’une force excessive et
des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
S3126A
9. VENTILATION - Slots and openings in the
cabinet and the back or bottom are provided for ventilation and to
ensure reliable operation of the TV and to protect it from overheating,
these openings must not be blocked or covered. The openings should
never be blocked by placing the TV on a bed, sofa, rug, or other similar
surface. This TV should never be placed near or over a radiator or heat
register. This TV should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your appliance dealer
2
EN
or local power company. For TVs intended to operate from battery
power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION - This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than
the other). This plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or cable
system is connected to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
14. LIGHTNING - For added protection for this TV receiver during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV due to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located in
the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
instructions, as improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this indicates
a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be sure the
service technician uses replacement parts specified by the manufacturer that
have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this TV,
ask the service technician to perform routine safety checks to determine
that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
PRECAUTIONS
•
•
•
•
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
IMPORTANT SAFEGUARDS / PRECAUTIONS
16. OVERLOADING - Do not overload wall outlets and extension cords as
this can result in a risk of fire or electric shock.
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference unless the modifications are expressly approved in the
owner’s manual. The user could lose the authority to operate this equipment if an unauthorized change or
modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground should be
connected to the grounding system of the building as close to the point of cable entry as practical.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Model No.
Serial No.
Dealer Purchase from
Date of Purchase
Dealer Phone No.
Dealer Address
A NOTE ABOUT RECYCLING:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
3
EN
SUPPLIED ACCESSORIES
• Owner’s Manual
(1EMN22175)
• Remote control unit
(NF006UD)
• Batteries
(“AA” x 2)
• If you need to replace these accessories, please refer to the PART NO. with the illustrations and call our toll free customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of Combiners (Mixers) or Separator (Splitters). Contact
your local electronics store for these items.
FEATURES
• DTV/TV/CATV
You can use your remote control to select channels which
are broadcast in conventional analog, standard definition,
and high definition formats. Also, cable subscribers can
access their cable TV channels.
• Program Information Display (DTV only)
You can display the title, contents and other information of
the current DTV program on the screen.
• Autoscan
This TV can automatically scan and memorize the channels
receivable in your residential area. This feature eliminates the
need of a difficult setting procedure.
• V-CHIP
This feature allows you to block children’s access to inappropriate programs.
• Closed Caption Decoder
This TV contains the built-in Closed Caption Decoder that
displays text across the screen. It allows you to read the
dialogue of a TV program or other information in the Closed
Caption-supported programs.
• MTS/SAP Tuner
This feature allows you to select with the remote control
your desired audio language.
• Auto Shut Off Function
If there is no signal input from the antenna terminal and
no operation for 15 minutes, the unit will turn itself off
automatically.
• Choices for On-Screen Menu Language
Select your setup menu language: English, Spanish or
French.
• Stereo Sound Function
• Full-Function Remote Control
• PLL Frequency Synthesized Tuning
• HDMI Input
This TV accepts 480i / 480p / 720p / 1080i video signals
and 32kHz / 44.1kHz / 48kHz audio signals.
• Component VIDEO Input
This TV accepts 480i / 480p / 720p / 1080i video signals.
• S-VIDEO Input
• AV Input
• Analog Audio Output
• Digital Audio Output (Coaxial)
• Resume
This feature will automatically memorize settings if a
power failure occurs.
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded
or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai.
Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein
without the obligation to notify any person or organization of such changes.
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the
express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to
use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
4
EN
IMPORTANT SAFEGUARDS
PRECAUTIONS . . . . . . . . . .
SUPPLIED ACCESSORIES .
FEATURES . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
3
4
4
FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REMOTE CONTROL, TOP AND REAR PANEL FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
BATTERY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ANTENNA CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTION TO CABLE/SATELLITE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTING OTHER DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
COMPONENT CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
S-VIDEO CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
VIDEO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DIGITAL AUDIO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
ANALOG AUDIO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INITIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INITIAL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CHANNEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
AUTOSCAN . . . . . . . . . . . .
CHANNEL LIST . . . . . . . . .
MANUAL REGISTER . . . . .
ANTENNA CONFIRMATION
LANGUAGE SELECTION . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
13
14
15
16
17
WATCHING TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CHANNEL SELECTION . . . . . . . . . . . . . . .
VOLUME ADJUSTMENT . . . . . . . . . . . . . .
STILL MODE . . . . . . . . . . . . . . . . . . . . . . .
SELECTING AUDIO CHANNELS . . . . . . . .
ACCESSING EXTERNAL DEVICES . . . . . .
CHANGING THE SCREEN DISPLAY MODE
SCREEN INFORMATION . . . . . . . . . . . . . .
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
SUPPLIED ACCESSORIES / FEATURES / CONTENTS
CONTENTS
18
18
19
19
20
21
22
23
OPTIONAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SETUP SCREEN . . . . . . .
PICTURE ADJUSTMENT .
CLOSED CAPTION . . . . . .
DTV CLOSED CAPTION . .
CLOSED CAPTION STYLE
V-CHIP . . . . . . . . . . . . . . .
HDMI AUDIO . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
24
25
26
26
28
31
MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
SYMBOLS USED IN THIS MANUAL
The following is the description for the symbols used in this manual.
TV
: Analog TV operation.
DTV
: Digital TV operation.
• If neither symbol appears under the function heading, operation is applicable to both.
5
EN
FUNCTIONS
REMOTE CONTROL, TOP AND REAR PANEL FUNCTION
SLEEP button (p23)
Press to activate the sleep timer.
INPUT
SLEEP SELECT
POWER
POWER button (p12)
Press to turn the TV on and off.
INPUT SELECT button (p20)
Press to access connected external
devices like a DVD recorder or VCR.
AUDIO button (p19)
1
2
3
4
5
6
Press to display on-screen menu.
7
8
9
s / B / K / L buttons (p12)
To move left / right / up / down through
the items.
-
0
Number buttons (p18)
Press to select a channel.
SETUP button (p23)
AUDIO
STILL
INFO
BACK
CH RETURN
VOL. X/ Y buttons (p18)
VOL.
Press to adjust volume.
MUTE button (p18)
Press to turn sound on and off.
MUTE
SCREEN MODE button (p21)
Press to select screen aspect ratio.
INFO button
ENTER
BACK button (p22)
Press to return to previous menu operation.
STILL button (p19)
Press to pause screen image.
SCREEN
MODE
SETUP
ENTER button (p12)
Press to confirm your selection.
• Analog mode (TV)
Selects audio mode.
• Digital mode (DTV)
Selects audio language.
CH
• Analog mode (TV) (p22)
To display channel No., signal type
and TV setting.
• Digital mode (DTV) (p22)
To display channel information, signal
type and TV setting.
• External input mode (p20)
To display external input mode, signal
type and TV setting.
CH K/ L buttons (p18/p20)
CH RETURN button (p18)
To select channels and external input
mode.
Press to return to previously viewed channel.
SETUP button (p23)
To display on-screen menu.
VOLUME X/ Y buttons (p18)
To adjust volume and move right(X)/left(Y) through the
menu items.
CHANNEL K/ L buttons (p18)
TV CONTROL
SETUP
VOLUME
CHANNEL
INPUT SELECT/
ENTER
POWER
To select channels and move up/down through the menu
items.
POWER button (p12)
To turn TV on/off.
INPUT SELECT/ENTER button (p20/p12)
• To access connected external devices like a DVD
recorder or VCR.
• To decide the command of setting when the menu is
displayed.
Infrared Sensor Window
STANDBYON
POWERON Receives infrared rays transmitted from the remote
control.
NOTE:
• With buttons [VOL. X/ Y] or [MUTE], you can only adjust the volume of the main unit. You cannot adjust the volume of the
external devices with these buttons.
6
EN
AUDIO OUT jacks
Audio cable connection for external
audio equipment. Use AUDIO IN jacks
of external equipment.
DIGITAL AUDIO OUT
(COAXIAL) jack
Digital audio coaxial cable
connection for decoder or
audio receiver. Connect cable
to DIGITAL AUDIO IN jack of
external device.
ANT. IN
L
L
AUDIO OUT
DIGITAL
AUDIO OUT
(COAXIAL)
R
HDMI IN
HDMI
from underneath
Y
ANT. IN
Y
VIDEO
VIDEO
DIGITAL
AUDIO OUT
(COAXIAL)
L
AUDIO OUT
R
L
L
Pb
R
Pr
AUDIO
AUDIO
R
HDMI IN
HDMI
L
Pb
R
Pr
L
AUDIO
COMPONENT2
AUDIO
L
S-VIDEO1
AUDIO
R
COMPONENT1
VIDEO2
R
VIDEO1
S-VIDEO2
INNER JACKS
INNER JACKS
COMPONENT1 and
AUDIO jacks
Component cable
connection for external
audio/video devices. Use
component and audio out
jacks of external device.
COMPONENT2 and
AUDIO jacks
Component cable
connection for external
audio/video devices. Use
component and audio out
jacks of external device.
AUDIO
R
AUDIO jacks (for DVI connection)
Audio cable connection for external
audio/video devices with DVI jack.
Use AUDIO OUT jacks of external
equipment when using an HDMI-DVI
conversion cable.
HDMI IN jack
Rear of this TV HDMI cable connection
for external video
equipment (i.e.DVD
recorder).
FUNCTIONS
ANT. IN jack
Coaxial cable connection for
your antenna or cable box.
from underneath
Y
Y
Pb
AUDIO
Pr
AUDIO
Pr
R
R
COMPONENT2
VIDEO
Pb
L
L
VIDEO
COMPONENT1
L
L
AUDIO
AUDIO
R
R
VIDEO2
VIDEO2 and AUDIO jacks
Video and audio cable
connection for external
equipment.
VIDEO1
S-VIDEO1
S-VIDEO2
S-VIDEO1 jack
S-Video cable and audio
(VIDEO1) cable connection for
external video equipment.
S-VIDEO2 jack
S-Video cable and audio
(VIDEO2) cable connection for
external video equipment.
VIDEO1 and AUDIO jacks
Video and audio cable
connection for external
equipment.
INSTALLING THE BATTERIES
Install two AA batteries (included) matching the polarity (++ / – –) indicated inside battery compartment of
the remote control.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh
ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
7
EN
PREPARATION FOR USE
CONNECTION
This section describes how to connect your TV to an antenna, cable box, etc.
MAKE SURE YOU HAVE AN ANTENNA.
As DTV is only available over the air, you need an antenna to receive a digital signal.
NOTE:
• Be sure your antenna or other source is connected properly before plugging in the power cord.
[ANTENNA CABLE CONNECTION]
1) When connecting your TV to an antenna
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.
2) When connecting TV to cable TV company (without box)
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.
VHF / UHF
antenna
Rear of this TV
Coaxial cable
(not included)
or
ANT. IN
Y
L
AUDIO OUT
L
L
Pb
R
Pr
AUDIO
AUDIO
R
Cable TV
company
Y
VIDEO
VIDEO
DIGITAL
AUDIO OUT
(COAXIAL)
ANT. IN
Coaxial cable
R
HDMI IN
HDMI
L
Pb
R
Pr
L
AUDIO
AUDIO
COMPONENT2
COMPONENT1
L
S-VIDEO1
AUDIO
R
VIDEO2
R
VIDEO1
S-VIDEO2
INNER JACKS
INNER JACKS
(not included)
*Once connections are completed, turn on the TV and begin initial setup.
Channel scanning is necessary for the TV to memorize all available channels in your area.
(Refer to “INITIAL SETUP” on page 12.)
NOTES:
• For your safety and to avoid damage to equipment, please unplug the coaxial cable from the ANT.IN jack before moving the unit.
• If you use an antenna in order to receive analog TV, the same antenna generally will work for DTV reception.
Outdoor or attic antennas will be more effective than set-top versions.
• To easily switch between antenna and cable wires, you can purchase an “Antenna Selector” commercially available.
• If you connect a cable system directly, contact the CATV installer.
[CONNECTION TO CABLE/SATELLITE BOX]
1) Connect the coaxial cable on your home outlet to the input jack of the CABLE/SATELLITE box.
2) Use another coaxial cable to connect the ANT. IN jack of your TV to the output jack of the CABLE/SATELLITE box.
*Required cables in 2) and connecting methods differ depending on the CABLE/SATELLITE box. For more information, please contact your cable/satellite provider.
Satellite
dish
Rear of this TV
Cable box or
Satellite box
or
Cable TV
company
8
EN
Coaxial cable
Coaxial cable
(not included)
(not included)
Y
ANT. IN
ANT. IN
Y
VIDEO
VIDEO
DIGITAL
AUDIO OUT
(COAXIAL)
L
AUDIO OUT
R
L
AUDIO
L
Pb
R
Pr
AUDIO
R
HDMI IN
HDMI
INNER JACKS
L
Pb
R
Pr
L
AUDIO
AUDIO
COMPONENT2
INNER JACKS
COMPONENT1
L
S-VIDEO1
AUDIO
R
VIDEO2
R
VIDEO1
S-VIDEO2
CONNECTING OTHER DEVICES
[HDMI]
1) High Definition Multimedia Interface (HDMI) uses the latest technology to ensure the signal maintains the
highest degree of integrity from source to TV. Both video and audio travel through a single cable.
PREPARATION FOR USE
HDMI cable (not included)
To HDMI IN jack
HDMI OUT
ANT. IN
L
L
AUDIO
AUDIO OUT
To HDMI output jack
DIGITAL
AUDIO OUT
(COAXIAL)
DVD Player with the HDMI output jack
HDMI IN
R
R
HDMI
Rear of this TV
NOTES:
• This TV accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.
• This TV accepts only 2 channel audio signal (LPCM).
• You need to select “PCM” for the digital audio output of the device you connect or the HDMI audio setting. Audio sometimes makes
no sound if you select “Bitstream”, etc.
• This TV only accepts signals corresponding EIA861.
2) When your video device has a DVI output jack, connect the HDMI conversion cable (not included) from the
DVI output jack.
HDMI-DVI conversion cable (not included)
To HDMI IN jack
To DVI output jack
DVI OUT
ANT. IN
L
L
AUDIO
AUDIO OUT
Cable Box or Satellite Box
with the DVI output jack
AUDIO OUT
R
L
DIGITAL
AUDIO OUT
(COAXIAL)
R
HDMI IN
R
HDMI
To audio
output jacks
To AUDIO Rear of this TV
input jacks
Audio cable (not included)
NOTES:
• This TV accepts 480i / 480p / 720p / 1080i video signals.
• An HDMI conversion cable requires a separate audio cable connection as well.
• Audio signals are converted from digital to analog if you make the connection in paragraph 2) above.
• DVI does not show image if the 480i does not accept EIA/CEA-861/861B.
“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.”
9
EN
[COMPONENT CABLE CONNECTION]
Offers better picture quality for video devices connected to your TV.
Use a component video cable (not included) to connect your TV to external video devices equipped with
component video jacks.
If you connect to your TV’s COMPONENT1 input jack, connect audio cables to the AUDIO L/R jacks of COMPONENT1.
If you connect to your TV’s COMPONENT2 input jack, connect audio cables to the AUDIO L/R jacks of COMPONENT2.
Component video cable (not included)
To COMPONENT1
input jacks
To component video
output jacks
Y
Y
Pb
AUDIO
AUDIO
Pr
Pr
R
R
COMPONENT2
To audio
output jacks
COMPONENT1
L
L
AUDIO
AUDIO
R
R
VIDEO2
VIDEO1
S-VIDEO1
S-VIDEO2
Rear of this TV
To AUDIO
input jacks
Audio cable (not included)
VIDEO
Pb
L
L
DVD Player with the component
video output jacks
VIDEO
NOTE:
• This TV accepts 480i / 480p / 720p / 1080i video signals.
[S-VIDEO CABLE CONNECTION]
Offers good picture quality for video devices connected to your TV.
Use an S-video cable (not included) to connect your TV to external video devices equipped with S-video connectors.
If you connect to your TV’s S-VIDEO1 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO1.
If you connect to your TV’s S-VIDEO2 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO2.
To S-VIDEO1
input jack
S-video cable (not included)
To S-Video
output jack
AUDIO
OUT
Y
VIDEO S-VIDEO
OUT
OUT
Pb
L
To audio
output jacks
Pr
R
VIDEO
VIDEO
Pb
L
AUDIO
DVD/VCR with
the S-Video output jack
Y
AUDIO
Pr
R
COMPONENT2
Audio cable (not included)
COMPONENT1
L
L
AUDIO
AUDIO
R
R
VIDEO2
VIDEO1
NOTE:
EN
S-VIDEO2
To AUDIO Rear of this TV
input jacks
• If you connect to the S-VIDEO jack and the VIDEO jack at the same time, the S-video connection will have priority.
10
S-VIDEO1
[VIDEO CONNECTION]
Offers standard picture quality for video devices connected to your TV.
When the audio jack of the video device is monaural, connect the audio cable to the audio L input jack.
To video
output jack
AUDIO
OUT
Y
VIDEO
OUT
Pb
Video Game
AUDIO
To audio
output jacks
VIDEO
Pr
AUDIO
Pr
R
R
COMPONENT2
VIDEO
Pb
L
L
Camcorder
Y
PREPARATION FOR USE
To VIDEO1
input jack
Video cable (not included)
COMPONENT1
VCR
L
L
AUDIO
AUDIO
R
R
VIDEO2
VIDEO1
S-VIDEO1
S-VIDEO2
To AUDIO Rear of this TV
input jacks
Audio cable (not included)
[DIGITAL AUDIO CONNECTION]
If you connect this TV to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound. Required digital audio coaxial cable not included.
Digital audio coaxial cable
(not included)
To DIGITAL AUDIO
OUT jack
MD deck, DAT deck, etc.
COAXIAL
ANT. IN
L
L
AUDIO OUT
To coaxial digital
audio input jack
DIGITAL
AUDIO OUT
(COAXIAL)
AUDIO
HDMI IN
R
R
HDMI
Rear of this TV
Dolby Digital decoder
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
[ANALOG AUDIO CONNECTION]
If you connect this TV to an external analog audio device, you can enjoy stereophonic (2 channel) audio
sound. Required audio cable not included.
To audio input jacks
AUDIO
IN
ANT. IN
L
L
AUDIO OUT
DIGITAL
AUDIO OUT
(COAXIAL)
R
AUDIO
HDMI IN
R
HDMI
Stereo system
Audio cable
(not included)
To AUDIO
OUT jacks
Rear of this TV
11
EN
INITIAL SETTINGS
INITIAL SETUP
3
This section will guide you through your TV’s initial
set up which includes selecting a language for your
on-screen menu and AUTOSCAN, which automatically scans and memorizes viewable channels.
When you first turn on your TV, the following
screen is displayed. Use [K /L] to select the
on-screen menu language from the choices on
the right side of the screen.
Initial Setup
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
Select the language for setup display.
English
Elija idioma de preparación.
Español
Sélectionner langue écran config.
Français
Select
ENTER
Enter
SETUP
Exit
AUDIO
7
8
-
0
9
The Antenna Confirmation menu on step 4 will
be displayed in the selected language after you
press [ENTER].
STILL
SCREEN
MODE
SETUP
4
ENTER
BACK
INFO
Select source of ANT. IN jack using [K /L], then
press [ENTER].
Initial Setup
1
2
After making all the necessary connections, turn
on your TV.
Cable
Air
Press [POWER]. Initial Setup menu will appear.
Or
Cable
ANT IN
• This operation may take a few moments.
• If Initial Setup menu does not appear, press
and hold [ENTER] for 3 seconds, initial setup
will appear then proceed to step 3. If initial set
up has already been completed, refer to
“LANGUAGE SELECTION” on page 17.
Air
Make sure the antenna is connected to "ANT IN" jack.
Select the destination of "ANT IN" jack.
Select
5
ENTER
Enter
BACK
SETUP
Back
Exit
Autoscan will start automatically.
Initial Setup
Now the system is scanning for channels,please wait.
5%
Analog channels
1ch
Digital channels
0ch
SETUP
Exit
• When scanning has completed, the lowest
memorized channel will be displayed.
NOTES:
• The initial Autoscan function can be executed for either “Air”
or “Cable” only once. When you change the connection
(Air/Cable), set the “Autoscan” again. (Refer to page 13.)
• If you connect a cable system directly, contact the
CATV installer.
• When the scanning is not complete, Helpful Hint will be
displayed every time you turn on the power. If you have
previously registered channels when this screen appears
you can select a channel with [the Number buttons].
2-0
No channel is registered.
Press and hold "ENTER" key for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Mantenga oprimida la tecla "ENTER" durante 3 segundos.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Maintenir la touche "ENTER" pressée 3 secondes.
Contacter numero d'urgence dans manuel ou arrière appareil.
• Toll free customer support line can be found on the cover
of this manual.
12
EN
CHANNEL SETTINGS
AUTOSCAN
With AUTOSCAN, your TV automatically scans and
memorizes your area’s viewable channels. Activate
AUTOSCAN when you turn on your TV for the first
time, change broadcast sources (e.g. from antenna
to CATV), or move your TV to a different broadcast
area.
3
For TV channels, using [K /L], select “Air”.
For CATV channels, select “Cable”.
Autoscan
Cable
Air
Cable
1hour
Cable
Or
ANT IN
SCREEN
MODE
ENTER
INFO
BACK
• Press [ENTER].
Scanning and memorizing the channels automatically starts.
CH RETURN
MUTE
Now the system is scanning for channels, please wait.
CH
72%
Analog channels
10ch
Digital channels
SETUP
NOTE:
• Make sure the TV is connected to antenna or cable.
1
INITIAL SETTINGS / CHANNEL SETTINGS
0
SETUP
VOL.
Air
Select the destination of "ANT IN" jack.
STILL
-
Back
Autoscan will rescan all channels.
This may take a while to complete.
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
6ch
Exit
• When the scanning and memorizing are completed, the lowest memorized channel in the
broadcasting will be displayed.
NOTES:
• If you connect a cable system directly, contact the
CATV installer.
• If you press [POWER] or [SETUP] during Autoscan, this
setting will be canceled.
• If there is no reception connected or a poor signal is detected, a Hint will appear on screen once scanning stops.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Autoscan”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
13
EN
CHANNEL LIST
3
This function lets you remove undesired channels
from the Channel Registration List.
Select the channel you want to remove.
• Using [K/L], select the channel.
Channel List
STILL
-
Highlight channels for
Ch Up/Down key selection.
0
SCREEN
MODE
SETUP
DTV
6
DTV
8
DTV
48
DTV
67
9
27
58
ENTER
Ch Select
INFO
BACK
1
MUTE
CH
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Channel List”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
14
EN
Back
NOTE:
• The channel with “DTV” indicated on the display is ATSC,
otherwise the channel is NTSC.
4
2
Watch/Skip
• Press [ENTER] to highlight the channel selected for removal. You will not be able to select the
channel again using [CH K/L].
• To reactivate the removed channel, highlight it
and press [ENTER].
• When you remove a major channel, you
remove its minor channels, too.
CH RETURN
VOL.
ENTER
BACK
To exit the setup, press [SETUP].
MANUAL REGISTER
3
Select the channel you want to add.
• Using [the Number buttons], select your
desired channel.
This function lets you manually add channels not
memorized due to poor broadcast strength during
AUTOSCAN.
11
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
7
8
9
Manual Register
For Analog channels,
select a channel to register
using number keys.
For Digital channels,
you must perform Autoscan function.
Register
AUDIO
Back
CHANNEL SETTINGS
BACK
Ch Change
STILL
-
0
• Select “Register” with [ENTER].
SCREEN
MODE
SETUP
4
To exit the setup, press [SETUP].
ENTER
BACK
1
INFO
Display the setup screen.
NOTES:
• If set up completes successfully, “Registered to the Channel
List” is displayed.
• If Video 1 is being used, set up will not be completed successfully and “Unavailable” will be displayed on the screen.
• Press [SETUP].
The following setup screen appears.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Manual Register”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
15
EN
ANTENNA CONFIRMATION
• If the channel is set to external input, you cannot confirm the antenna situation.
Displays signal strength for each channel.
Video1
INPUT
SLEEP SELECT
POWER
Antenna
Back
1
2
3
4
5
6
Indicator is available
for antenna signal only.
AUDIO
7
8
-
0
9
STILL
CH
SETUP
3
ENTER
INFO
BACK
CH RETURN
VOL.
1
CH
MUTE
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Antenna”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
• Using [the Number buttons] or [CH K /L],
select the channel for which you want to check
signal strength.
11
Antenna
Back
Now
70 Peak
CH
16
EN
Ch Change
SCREEN
MODE
80
Ch Change
To exit the setup, press [SETUP].
LANGUAGE SELECTION
You can choose English, Spanish, or French as
your on screen language.
STILL
-
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
1
MUTE
CHANNEL SETTINGS
CH RETURN
VOL.
CH
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “LANGUAGE” and press [ENTER] to confirm.
• Using [K /L], select “English”, “Español” or
“Français”.
Language
Select the language for setup display.
English
Elija idioma de preparación.
Español
Sélectionner langue écran config.
Français
• Press [ENTER].
3
To exit the setup, press [SETUP].
17
EN
WATCHING TV
CHANNEL SELECTION
Select channels by pressing [CH K/L] found on
remote control or on the TV’s control panel, or by
pressing [the Number buttons] found on the remote
control.
1
2
3
4
5
6
7
8
9
ATSC
18:00
CH4-1 No signal No signal
18:30
CH4-1
CH4-2
CH4-3
19:00
CH4
CH4-1 No signal CH4-3
INPUT
SLEEP SELECT
POWER
19:30
CH4-1
CH4-2 No signal
20:00
AUDIO
STILL
-
NTSC
: change automatically
: change manually by pressing [CH
on your remote control
/ ]
0
SCREEN
MODE
SETUP
NOTE:
• “No Signal” will appear on the screen after the minor
ENTER
INFO
BACK
CH RETURN
VOL.
MUTE
VOLUME ADJUSTMENT
CH
[CH K/L]
• Use [CH K/L] to change the channel.
• Same operation is also available with [CHANNEL K/L] on the top panel of the main unit.
[the Number buttons]
• Press the channel number with [the Number
buttons] to select a channel you want to watch,
then press [ENTER].
- When selecting analog channel 12
1
2
ENTER
- When selecting digital channel 12-1
Be sure to press [–] before entering the minor
channel number.
1
2
-
1
NOTE:
• In DTV broadcasting, one channel sometimes broadcasts
multiple programs depending on the air time. In this case,
the main channel is called major channel and the minor
channel is called minor channel.
About minor channel broadcasting:
There may be different programs being broadcast on minor channels through a single channel from ATSC. You can watch each minor
channel program being broadcast by selecting
one of the minor channels.
EN
This section describes how to adjust the volume.
The mute function, which turns the sound off and
on, will also be described.
INFO
BACK
CH RETURN
VOL.
MUTE
CH
[VOL. X/Y]
• Use [VOL. X/Y] to adjust the audio volume.
• The same operation is available with [VOLUME
X/Y] on the top panel of the main unit.
• The volume bar will be displayed at the bottom
of the screen when adjusting the volume.
Volume
20
ENTER
• If the channel broadcasts NTSC and ATSC both
and you don't press [–], you will receive the
NTSC channel only. The moment you press [–],
the lowest memorized digital channel will be displayed.
• Press [CH RETURN] to return to the previously
viewed channel.
18
channel broadcast is over.
You will need to change the channel to continue
watching another TV program.
• The volume bar display will automatically disappear in a few seconds.
[MUTE]
• Press [MUTE] to turn off and on the sound.
Mute
• “Mute” is displayed on the screen for a few seconds.
• Press [MUTE] again or [VOL. X/Y] ([VOLUME
X/Y]) to release the Mute status.
STILL MODE
When the broadcasting has all audio...
You can freeze the image shown on the screen.
1
2
3
4
5
6
7
8
9
-
0
SAP / STEREO
SAP / STEREO
SAP / MONO
AUDIO
When the broadcasting has stereo audio and
monaural audio...
STILL
SCREEN
MODE
SETUP
MONO / STEREO
MONO / STEREO
When the broadcasting has SAP and monaural
audio...
Pause the image.
• When you press [STILL], the image shown on
the screen is paused.
SAP / MONO
SAP / MONO
When the broadcasting is having only monaural
audio...
WATCHING TV
1
MONO
Still
(cannot be switched.)
• The audio is not paused and keeps on reading
out.
• If the digital signal is gone or protected, the
image will remain paused and the audio will be
muted.
• The Still function will be released after 5
minutes.
2
Canceling Still function.
• The Still function will be canceled by pressing
any button while Still function is working.
NOTE:
• Press any key except [POWER] to cancel still mode.
SELECTING AUDIO CHANNELS
This section describes how to switch the audio in
the analog mode and how to switch the audio language in the digital mode.
AUDIO
7
8
-
0
9
STILL
SETUP
SCREEN
MODE
STEREO : Outputs stereo-audio
SAP
: Outputs second audio program
MONO : Outputs mono-audio
DTV
When you press [AUDIO], the currently selected
language and the number of available languages
will be displayed on the screen.
6-1
English 1/3
Press [AUDIO] to cycle through available audio
languages.
English 1/3
Spanish 2/3
Other 3/3
• Available languages differ depending on the
broadcast.
• The information display will automatically disappear in one minute.
NOTE:
• Pressing [AUDIO] does not control external audio source.
TV
When you press [AUDIO], the currently selected
audio mode will be displyed on the screen.
6
SAP / STEREO
Press [AUDIO] to cycle through available audio
channels.
19
EN
ACCESSING EXTERNAL DEVICES
Use your remote control to access DVD recorders,
home audio systems and other external devices
when they are connected to your television.
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
7
8
9
• When you press [INFO], the current external
input mode, the type of resolutions for video
signal, TV aspect ratio, CC and TV rating will
be displayed at the top-right of the screen.
• The information display will automatically disappear in 1 minute.
1) When using VIDEO1 or S-VIDEO1 input jack
AUDIO
Video1
480i
STILL
-
SD
TV-PG DLSV CC
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
2) When using VIDEO2 or S-VIDEO2 input jack
Video2
CH RETURN
480i
VOL.
MUTE
CH
Use your remote control to select external component.
• When you press [INPUT SELECT] or [CH L]
on the remote control, the input mode will be
switched as below.
SD
TV-PG DLSV CC
3) When using COMPONENT1 input jacks
Component1
1080i
HD
NONE
TV/DTV channel
Video1
4) When using COMPONENT2 input jacks
Component2
1080i
Video2
HD
NONE
Component1
5) When using HDMI IN jack
Component2
HDMI
1080i
HD
NONE
HDMI
• Pressing [CH K] on the remote control reverses
direction.
• To use the VIDEO1 or S-VIDEO1 input jack on
the TV, select “Video1”.
• To use the VIDEO2 or S-VIDEO2 input jack on
the TV, select “Video2”.
• To use the COMPONENT1 input jacks on the
TV, select “Component1”.
• To use the COMPONENT2 input jacks on the
TV, select “Component2”.
20
EN
• To use the HDMI IN jack on the TV,
select “HDMI”.
16:9
CHANGING THE SCREEN DISPLAY MODE
Each of 4 display modes can be selected in either
4:3 or 16:9 aspect ratios.
AUDIO
7
8
9
STILL
-
1
Press [SCREEN MODE], to switch the TV
aspect ratio.
2
Press [SCREEN MODE] repeatedly until the normal screen displays.
0
NOTE:
SCREEN
MODE
SETUP
• Some programs may not offer all display mode options.
ENTER
INFO
When the broadcast is sending 4:3 video
signal...
When the broadcast is sending 16:9 video
signal...
Sidebar
(normal)
Full
Full
(normal)
Zoom
Wide
Cinema
Expand
Cinema
[Sidebar]
Sidebar displays a 4:3 picture at its standard
4:3 size. Sidebars will be displayed on the right
and left edges of the screen.
[Full]
Full displays a 4:3 picture at a 16:9 size, with
horizontal elongation necessary to fill the
screen.
[Cinema]
Cinema displays a 4:3 picture at a 16:9 size,
with less horizontal elongation necessary to fill
the screen because a little bit of the top and
bottom edge of the screen will be cut off.
[Wide]
Wide displays the center of the picture as original
size and the outer sides of the picture will be
elongated. The size of the picture will depend on
the original signal.
WATCHING TV
BACK
[Full]
A picture is displayed at 16:9 size as it is.
[Zoom]
Zoom displays a 16:9 picture without changing
its horizontal and vertical ratio, at its maximum
size.
[Cinema]
Cinema displays a 16:9 picture with vertical
elongation.
[Expand]
Expand displays a 16:9 picture with horizontal
elongation.
21
EN
DTV
SCREEN INFORMATION
You can display the currently selected channel or
other information such as the audio mode on the
screen.
1
AUDIO
7
8
9
-
0
SCREEN
MODE
• The following information is displayed.
ENTER
(1) Program title
INFO
BACK
(2) Broadcast station
CH RETURN
VOL.
MUTE
Display the detailed information for the channel.
• Press [INFO] on the remote control.
The currently selected program details are displayed on the screen.
STILL
SETUP
In the digital mode, the detailed information for the
current channel such as the Program guide is displayed.
(3) Program guide (max. 4 lines displayed)
CH
(4) Channel number
TV
In the analog mode, the current channel and the
audio mode are displayed.
1
(5) Audio language (“Other” is displayed when
the audio language cannot be acquired, or
the acquired languages are other than
English, Spanish or French.)
Display the channel number and the audio
mode.
(6) Effective scanning lines and scan mode
• Press [INFO] on the remote control.
The current channel number, audio mode, type
of resolutions for video signal, TV aspect ratio,
CC and TV rating are displayed at the top-right
of the screen.
(8) Program aspect ratio
(7) Program definition
(9) Program rating
(10) CC (Not available if the CC set to “Off”)
(1)
Buffy Vampire Slayer
6
SAP / STEREO
480i
480i
SD
SD
4:3
4:3
(2)
(4)
HDTV
A quarter-century ago,which may now qualify as the
good old days of newspapering,run-of-paper sales
accounted for 80 percent of the industry's advertising
revenues.Department stores and supermarket were
6-1
(5)
English 1/2
1080i
1080i
HD
HD
16:9
16:9
TV-PG DLSV CC
CC
(6), (7), (8)
TV-PG DLSV CC
CC
(3)
• To clear the display, press [BACK] or [INFO]
again.
(9) (10)
NOTES:
• When the program guide is displayed in more than 4 lines,
use [ K/ L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• The following screen is displayed when connecting to external devices:
e.g.) When using VIDEO1 input jack for connection (Refer to “ACCESSING EXTERNAL
DEVICES” on page 20.)
Video1
480i
480i
SD
SD
TV-PG DLSV CC
CC
22
EN
OPTIONAL SETTINGS
SLEEP TIMER
SETUP SCREEN
The Sleep Timer can be set to automatically turn
off your television after an incremental period of
time.
This section describes the overview of the setup
screen displayed when you press [SETUP].
For more details, see the reference page for each
item.
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
The setup screen consists of the function setting
items below.
•
AUDIO
7
8
-
0
To exit settings.
9
STILL
•
SCREEN
MODE
You can adjust the picture quality (Picture Mode,
Brightness, Contrast, Color, Tint, Sharpness,
Color Temp., and Energy Saving).
(Refer to “PICTURE ADJUSTMENT” on page 24.)
ENTER
1 Press [SLEEP] on the remote control to set the
Sleep Timer.
•
• The setting display for Sleep Timer is shown on
the screen.
Sleep
WATCHING TV / OPTIONAL SETTINGS
SETUP
You can automatically scan the viewable channels
and remove those that are undesired.
(Refer to “AUTOSCAN” on page 13.)
Off
•
2
You can change closed captioning display formats
and font styles. (Refer to “CLOSED CAPTION” on
page 25.)
Block children’s access to inappropriate programming. (Refer to “V-CHIP” on page 28.)
And select HDMI Audio if your TV is connected to
a digital external device like a DVD recorder.
(Refer to “HDMI AUDIO” on page 31.)
You can set your TV to turn off after a set period
of time (from 10 to 90 minutes). After set up, you
can display the remaining time before shut off by
pressing [SLEEP] again.
• To cancel the sleep timer, press [SLEEP]
repeatedly until “Sleep Off” is displayed.
Sleep
Off
• The Sleep Timer setting display will automatically disappear in a few seconds.
NOTE:
• When you disconnect your TV from its power source or
when a power failure occurs, the sleep timer setting will be
cancelled.
•
You can change the language (English, Spanish,
French) displayed on the setup screen.
(Refer to “LANGUAGE SELECTION” on page 17.)
NOTE:
• To cancel the setup screen, press [SETUP].
23
EN
Contrast
Using [s / B], adjust to increase or decrease
contrast.
s: To decrease contrast
B: To increase contrast
PICTURE ADJUSTMENT
You can select from four default picture color settings. You can also adjust brightness, contrast,
color, tint, sharpness and color temperature as well
as energy saving settings.
Contrast
SCREEN
MODE
SETUP
INFO
Color
1
Display the setup screen.
Adjust
30
60
36
Enter
Move
ENTER
Enter
Picture
Brightness
0
Sharpness
ENTER
Picture Mode
0
Tint
Move
Color Temp.
Using [K/L], adjust Color Temperature from the selection, then press [ENTER]. (Cool, Neutral and Warm)
Dynamic
Color
Enter
Sharpness 0
Picture
Contrast
ENTER
Sharpness
Using [s / B], adjust the detail of the picture.
s: To soft
B: To clear
Select “PICTURE”, and press [ENTER] to confirm.
• Using [K /L], select your desired item and
press [ENTER] to confirm.
Brightness
Move
R2
Adjust
Contrast
Neutral
Color Temp.
Color
Off
Energy Saving
3
Enter
Tint
Using [s / B], adjust to obtain natural skin tones.
s: To red
B: To green
Tint
Picture Mode
ENTER
36
Adjust
• Press [SETUP].
The following setup screen appears.
2
Move
Color
Using [s / B], adjust to be brilliant or pale color.
s: To pale
B: To brilliant
ENTER
BACK
60
Adjust
Tint
Adjust the picture quality.
• Using [K/L], select the picture quality you want
to adjust.
Standard
Dynamic
Contrast
Movie
Color
News
Tint
Manual
Neutral
Energy Saving
Warm
Energy Saving Off
Adjust
ENTER
Enter
• The adjustment bar for picture quality item is
displayed on the screen.
Picture
Brightness
Cool
Color Temp.
Energy Saving
Using [s / B], adjust brightness of backlight.
s: To bright
B: To dark
Picture Mode
Using [K /L], adjust Picture Mode from the
selection, then press [ENTER]. (Standard,
Dynamic, Movie, News and Manual)
Picture Mode
Sharpness
NOTE:
• To cancel the picture adjustment, press [SETUP].
Sharpness
Color Temp.
Energy Saving
4
Brightness
Using [s / B], adjust until the darkest parts of
the picture are as bright as you prefer.
s: To decrease brightness
B: To increase brightness
Brightness
30
Adjust
24
EN
Move
ENTER
Enter
To exit the setup, press [SETUP].
[Caption Mode]
CLOSED CAPTION
CC1 and Text1:
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
You can view closed captioning (cc) for TV programs, movies, news, and prerecorded tapes.
Closed captions refer to text of dialogue or descriptions displayed on-screen for the hearing impaired.
(up to 4 lines of script on the screen, where it
does not obstruct relevant parts of the picture).
STILL
-
0
SCREEN
MODE
SETUP
CC3 and Text3:
serve as the preferred data channels.
The captioning or text is often a secondary language translation, simplified English or displayed
at a slower rate.
ENTER
INFO
BACK
CH RETURN
1
CC2, CC4, Text2 and Text4:
are rarely available and broadcasters use them
only in special conditions, such as when CC1
and CC3 are not available or Text1 and Text3 are
not available.
CH
MUTE
Display the setup screen.
• There are three display modes according to
programs:
• Press [SETUP].
The following setup screen appears.
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Detail
Closed Caption
V–chip
HDMI Audio
3
Auto
Select “Conventional CC” and press [ENTER] to
confirm.
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
4
OPTIONAL SETTINGS
VOL.
Paint-on mode : Displays input characters on
the screen immediately.
Pop-on mode : Once characters are stored in
memory, they are displayed all
at once.
Roll-up mode : Displays the characters continuously by scrolling (max. 4
lines).
5
To exit the setup, press [SETUP].
NOTES:
• Closed captions must be broadcast or included in your
recorded content to appear on your TV.
• Closed captions will not be displayed when you are using
an HDMI connection.
• If the closed caption is not broadcasted, nothing is displayed.
• The closed caption is not displayed when you use HDMI
connection.
• When your TV receives a special effects playback signal
(i.e., Search, Slow and Still) from a VCR’s video output
channel (CH3 or CH4), the TV may not display the correct
caption or text.
• Captions and texts may not match the TV voice exactly.
• Interference may cause the closed caption system not to
function properly.
• The caption or text characters will not be displayed while the
menu display or functions display is shown.
• If a black box appears on the screen, this means that the
TV is set to TEXT mode. To clear screen, select CAPTION
“CC1”, “CC2” , “CC3”, “CC4”or “Off”.
Select the Closed Caption mode.
Closed Caption
Conventional CC
Off
DTV CC
CC1
CC Style
CC2
CC3
CC4
Text1
Text2
Text3
Text4
• Using [K /L], select the desired closed caption,
then press [ENTER].
25
EN
DTV CLOSED CAPTION
DTV
Apart from closed captions, DTV has its own closed
captions called DTV CC. Use this menu to change
the settings for DTV CC.
1
CLOSED CAPTION STYLE
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Detail
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Closed Caption
V–chip
HDMI Audio
Auto
Detail
Closed Caption
V–chip
HDMI Audio
Auto
3
Select “CC Style” and press [ENTER] to confirm.
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
3
Select “DTV CC” and press [ENTER] to confirm.
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
4
Switch the Closed Caption Style.
CC Style
User Setting
4
Font0
Font Size
Middle
Font Color
White
Font Opacity
Switch the DTV Closed Caption mode.
Closed Caption
Off
Font Style
Solid
Back Color
Black
Back Opacity
Solid
Edge Color
Black
Edge Type
None
Conventional CC
DTV CC
Off
CC Style
Service1
• Using [K /L], select the desired Closed Caption
Style.
Service2
Service3
Service4
Service5
Service6
• Using [K /L], select the desired DTV Closed
Caption, then press [ENTER].
Off:
Select if you do not want DTV CC. This is the
default.
Service 1 to Service 6:
Select one of these before changing any other
item in the Closed Caption menu. Choose
Service 1 under normal circumstances.
5
Use “User Setting”.
• The “User Setting” function lets you change CC
style.
• Using [K /L], select “User Setting”.
• Press [ENTER] and set “User Setting” to “On”.
CC Style
User Setting
On
Font Style
Off
Font Size
Font Color
Font Opacity
Back Color
Back Opacity
Edge Color
Edge Type
5
26
EN
To exit the setup, press [SETUP].
[Font Opacity]
Font opacity of the displayed caption can be
switched as below.
Set each item.
• When “User Setting” is set to “On”, you can set
the following items.
• CC style set by “User Setting” will be displayed.
• Using [K /L], select the item you want to set.
• You can switch the setting for each item with
[K /L].
CC Style
Closed Caption
User Setting
Font Style
Font Size
Font Color
Font Opacity
Solid
Back Color
Flash
Back Opacity
Translucent
Edge Color
Transparent
Edge Type
Picture display
[Back Color]
Background color of the displayed caption can
be switched as below.
ABCDEF
GHIJKL
ABCDEFGHIJKL
CC Style
Edge
(Edge Color and Edge Type)
Closed Caption
User Setting
Font
(Font Style, Font Size, Font Color and Font Opacity)
Back
(Back Color and Back Opacity)
• The setting description for each item is shown
below.
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
OPTIONAL SETTINGS
6
[Back Opacity]
Background opacity of the displayed caption can
be switched as below.
[Font Style]
Closed Captioning font style can be changed as
below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
User Setting
Font Size
Font Style
Font Color
Font Opacity
Font Size
Font Color
Back Color
Solid
Font Opacity
Back Opacity
Flash
Back Color
Edge Color
Translucent
Back Opacity
Edge Type
Transparent
Edge Color
Edge Type
[Edge Color]
Edge color of the displayed caption can be
switched as below.
[Font Size]
Font size of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
White
Font Size
Black
Font Color
Red
Font Size
Large
Font Opacity
Green
Font Color
Middle
Back Color
Blue
Small
Back Opacity
Yellow
Back Color
Edge Color
Magenta
Back Opacity
Edge Type
Cyan
User Setting
Font Style
Font Opacity
Edge Color
Edge Type
[Edge Type]
Edge type of the displayed caption can be
switched as below.
[Font Color]
Font color of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
Font Size
User Setting
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
7
Font Color
None
Font Opacity
Raised
Back Color
Depressed
Back Opacity
Uniform
Edge Color
L.Shadow
Edge Type
R.Shadow
To exit the setup, press [SETUP].
27
EN
V-CHIP
3
You can block certain programming inappropriate for
children. This block can be released by entering a
password.
Enter the password.
• Use [the Number buttons] and enter the
4-digit number.
V-Chip
INPUT
SLEEP SELECT
POWER
Enter password.
1
2
3
4
5
6
BACK
PIN Code
AUDIO
7
8
• When you have not set up your password,
enter 0000.
• When the password is correct, the following
“V-Chip” screen is displayed.
9
STILL
-
0
SCREEN
MODE
SETUP
Back
A MPAA Rating
V-Chip
ENTER
MPAA Rating
INFO
BACK
B TV Rating
TV Rating
New Password
C New Password
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
See the following description for setting each
item.
A MPAA Rating
4
Display the “MPAA Rating” screen.
• Using [K /L], select “MPAA Rating”.
V-Chip
2
Select “DETAIL” and press [ENTER].
• Using [K /L], select “V-chip”.
MPAA Rating
TV Rating
New Password
Detail
Closed Caption
V–chip
Auto
HDMI Audio
• Press [ENTER].
V-Chip
X
NC-17
R
PG-13
PG
G
NR
• Press [ENTER].
The password entry screen is displayed.
V-Chip
Select
Enter password.
PIN Code
28
EN
BACK
Back
ENTER
View/Block
BACK
Back
Set “MPAA Rating”.
• Using [K /L], select the rating.
• Press [ENTER] and set to “View” or “Block”.
5
• Press [ENTER] and set to “View” or “Block” for
the rating without sub categories.
V-Chip
X
NC-17
R
PG-13
PG
G
NR
Select
6
V-Chip
FV V
ENTER
View/Block
BACK
Back
PG-13 :
PG :
G:
NR :
<Rating Category Explanations>
Mature audience only
No one under 17 admitted
Restricted; under 17 requires
accompanying parent or adult
guardian
Unsuitable for children under 13
Parental Guidance suggested
General Audience
No Rating
NOTES:
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set “X” to “View”, all ratings turn to “View”
automatically.
B TV Rating
Display the “TV Rating” screen.
• Using [K /L], select “TV Rating”.
V-Chip
MPAA Rating
TV Rating
New Password
L
D
Select
ENTER
View/Block
BACK
Back
• For the rating with sub categories,
press [K /L / s / B] and select the rating. Then
press [ENTER] and set to “View” or “Block”.
V-Chip
FV V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
6
ENTER
View/Block
BACK
Back
To exit the setup, press [SETUP].
<Selection>
TV-MA :
TV-14 :
TV-PG :
TV-G :
TV-Y7 :
TV-Y :
<Rating Category Explanations>
Mature audience only
Unsuitable for children under 14
Parental Guidance suggested
General Audience
Appropriate for children 7 and
older
Appropriate for all children
<Selection>
FV :
V:
S:
L:
D:
<Rating Sub Category Explanations>
Fantasy Violence
Violence
Sexual Situation
Coarse Language
Suggestive Dialogue
NOTES:
• Press [ENTER].
V-Chip
FV V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
S
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
To exit the setup, press [SETUP].
<Selection>
X:
NC-17 :
R:
4
Set “TV Rating”.
• Using [K /L], select the rating.
OPTIONAL SETTINGS
5
ENTER
View/Block
BACK
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set “TV-MA” to “View”, all ratings turn to “View”
automatically.
Back
29
EN
C New Password
4
Display the “New Password” screen.
• Using [K /L], select “New Password”.
V-Chip
MPAA Rating
TV Rating
New Password
• Press [ENTER].
5
Change the password.
• Use [the Number buttons] on the remote control and enter the NEW 4-digit password.
• Enter password again in “Confirm password”
space.
V-Chip
Enter password.
Confirm password.
PIN Code
6
BACK
Back
To exit the setup, press [SETUP].
NOTES:
• Make sure to enter the exact same new password as the
“Confirm password.”. If they are different, the space is
cleared for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs or when you turn off the
power using a wall switch. If you forget the password,
unplug the power cord for 10 seconds to restore the password to 0000.
30
EN
HDMI AUDIO
Set the method of sound input for HDMI jack.
STILL
-
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
1
Display the setup screen.
2
OPTIONAL SETTINGS
• Press [SETUP].
The following setup screen appears.
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “HDMI Audio” and press
[ENTER] to confirm.
Detail
Closed Caption
V–chip
HDMI Audio
3
Auto
Switch the HDMI Audio.
• Using [K /L], select the desired HDMI Audio,
then press [ENTER].
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Digital
Analog
• Select “Auto” if you connected to both digital
device with HDMI jack and analog device for
audio sources. Digital audio input signal has
priority in this setting.
• Select “Digital” if you connected to digital
device with HDMI jack for digital audio input
signal.
• Select “Analog” if you connected to analog
device with analog jacks for analog audio input
signal.
4
To exit the setup, press [SETUP].
31
EN
MISCELLANEOUS
TROUBLESHOOTING GUIDE
Before calling for service, please refer to the following information.
Symptom
32
EN
Remedy
No power
• Be sure the power cord is connected to outlet.
• If a power failure occurs, unplug the power cord for 30 minutes
to allow the unit to reset itself.
No picture or sound
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on
again.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
• Adjust the Color in the setup screen.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• Adjust Contrast and Brightness in the setup screen.
• View other TV channels. The problem might be limited to the
broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Adjust Contrast and Brightness in the setup screen.
• View other TV channels. The problem might be limited to the
broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Picture blurred
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Bars on screen
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
Remedy
Picture rolls vertically
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Different color marks on screen
• Move your TV away from nearby electric appliances. Turn off the
power and wait 30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the
broadcasting station.
Poor reception on some channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Picture OK, sound poor
• View other TV channels. The problem might be limited to the
broadcasting station.
No reception of digital signals
• Make sure Autoscan has been completed (Refer to “AUTOSCAN” on
page 13). Autoscan must be completed when you set up your TV for
the first time or move it to a location where previously unavailable
channels are broadcast.
• The selected channel may not be broadcasting.
• When Autoscan is interrupted, some channels will not be
received. Make sure to complete Autoscan in the setup screen.
Channel changes automatically
• Many digital channels have alternate channel numbers. TV changes the
numbers automatically to the ones signifying the broadcasting stations.
These are the numbers used for analog broadcasts.
Remote Control doesn’t work
• Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the sensor and the
remote control.
• Test the signal output. If OK, there might be remote sensor trouble. (Refer to “IR SIGNAL CHECK” on page 34.)
MISCELLANEOUS
Symptom
Problems with Closed Caption Feature
Misspelled captions are displayed.
• Closed captioning production companies may broadcast programs without correcting the misspelling in a live broadcast.
Captions are not entirely displayed, or • Captions that are delayed a few seconds behind the actual dialogue
are common for live broadcasts. Most captioning production compacaptions are delayed behind the dianies can display a dialogue to a maximum of 220 words per minute. If
logue.
a dialogue exceeds that rate, selective editing is used to ensure that
the captions remain up-to-date with the current TV screen dialogue.
Captions are displayed as a white
box.
No caption is displayed in the Closed
Caption-supported program.
• Interference from buildings or weather conditions may cause
captioning to be incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed caption decoder cannot read the information of the shortened program.
No caption is displayed when playing
the videotape containing captions.
• The videotape may be illegally copied, or the caption signal
might not have been read during copying.
Black box is displayed in the screen.
• “Text” mode is selected for caption. Select “CC1”, “CC2”, “CC3”,
“CC4” or “Off”.
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels
may appear as a fixed point of blue, green or red. This is not to be considered a defect in the LCD screen.
33
EN
GLOSSARY
ATSC
Acronym that stands for Advanced
Television Systems Committee and
the name of the digital broadcasting
standards.
Aspect ratio
The width of a TV screen relative
to its height. Conventional TVs are
4:3 (in other words, the screen is
almost square); widescreen models are 16:9 (the screen is almost
twice as wide as its height).
Component video
This is a video signal format that
conveys each of three principal
colors of light (red, blue and
green) through different signal
lines. This allows the viewers to
experience picture colors as original as it is. There are several signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
Dolby Digital
The system developed by Dolby
Laboratories to compress digital
sound. It offers stereo sound (2ch)
or multi-channel audio.
HDMI (High-Definition
Multimedia Interface)
Interface that supports all uncompressed, digital audio/video formats
including set-top box, DVD player or
digital television, over a single cable.
High Definition TV (HDTV)
Ultimate digital format that produces
high resolution and high picture quality.
LPCM
(Linear Pulse Code Modulation)
LPCM is a format that can have
up to 8 channels of audio. It is
mainly used in music production.
The format samples and captures
analog signals and transforms
them into digital signals without
compressing the sound data.
NTSC
Acronym that stands for National
Television Systems Committee
and the name of the current analog broadcasting standards.
Password
A stored 4-digit number that
allows access to parental control
features.
SAP
(Secondary Audio Program)
Second-audio channel delivered
separately from main-audio channel. This audio channel is used as
an alternate in bilingual broadcasting.
Standard Definition TV (SDTV)
Standard digital format that is similar to the NTSC picture quality.
S-Video
Offers higher quality images by
delivering each signal, color (c)
and luminance (y) independently
of each other through separate
cables.
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
the TV with a soft cloth immersed in lukewarm
water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the TV. Such chemicals may
cause damage and discoloration to the exposed
surfaces.
LCD CLEANING
Wipe the LCD of the TV with a soft cloth. Before
cleaning the LCD, disconnect the power cord.
SERVICING
Should your unit become inoperative, do not try to
correct the problem yourself. There are no user serviceable parts inside. Turn off the TV, unplug the
power cord and call our toll free customer support
line found on the cover of this manual to locate an
authorized service center.
34
EN
IR SIGNAL CHECK
If the remote control isn’t working properly, you can
use an AM radio or digital camera (including a cellular phone with built-in camera) to see if it is sending
out an infrared signal.
• With an AM radio:
Tune the AM radio station to a
non-broadcasting frequency.
Point the remote control towards
it, push any button and listen. If
the sound from the radio flutters,
it is receiving the remote control’s
infrared signal.
• With a digital camera
(including built-in cell phone cameras):
Point a digital camera towards the
remote control. Push any button on the
remote control and look through the digital camera. If the infrared light appears
through the camera, the remote control
is working.
SPECIFICATIONS
Closed Caption
System:
ATSC
NTSC-M
TV Standard
§15.119/FCC (Analog CC)
§15.122/FCC (Digital CC)
Channel Coverage (ATSC/NTSC)
VHF:
2 ~ 13
UHF:
14 ~ 69
CATV:
2 ~ 13, A ~ W,
W+1 ~ W+94,
A-5 ~ A-1, 5A
Tuning System:
Channel frequency
synthesized tuning system
Channel Access:
Direct access keyboard,
Programmable scan,
and Up/down
Terminals
Antenna Input:
VHF/UHF/CATV
75 ohm unbalanced
(F-type)
S-Video Input:
Mini DIN 4-pin jack x 2
Video Input:
RCA jack x 2
Audio Input:
RCA jack (L/R) x 4
Component Video/Audio Input:
One pin jack (Y) / 1Vpp x 2
Two pin jacks (Pb/Pr) / 700mVpp x 4
RCA jack (L/R) x 4
HDMI / Audio Input:
HDMI jack
RCA jack (L/R) x 2
Coaxial Digital Audio Output:
One pin jack, 500mVpp
Analog Audio Output:
RCA jack (L/R) x 2
Stereo Sound System Speaker
ELECTRICAL SPECIFICATION
Sound Output:
5W, 8 ohm x 2
OTHER SPECIFICATIONS
Remote Control:
Digital encoded
infrared light system
Operating
Temperature:
5°C to 40°C
(41°F to 104°F)
Power Requirements: AC120V, 60Hz
Power Consumption
(Maximum):
160W
LCD:
32" wide XGA panel
(1,366 x 768 pixels)
Dimensions:
<Without stand>
H : 23.5"
(595mm)
W: 32.3"
(818mm)
D : 4.6"
(115mm)
<With stand>
H : 25.4"
(644mm)
W: 32.3"
(818mm)
D : 10.9"
(275mm)
Weight:
30.4 lbs. (13.8kg)
MISCELLANEOUS / SPECIFICATIONS
GENERAL SPECIFICATIONS
Television System:
• Designs and specifications are subject to change without notice and without our legal obligation.
• If there is a discrepancy between languages, the default language will be English.
35
EN
TM
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship
as follows:
DURATION:
PARTS:
LABOR:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Certain parts and LCD image burn-in are excluded from this warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or
if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not
purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does
not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES
INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL
BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging
or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI CORP. will not
reimburse you for any service done by unauthorized service providers without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at :
FUNAI CORPORATION
Customer Service
Tel :1-800-256-2487
http://www.EmersonAudioVideo.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
1EMN22175
L4406UG ★★★★★
Download PDF

advertising