Owner`s manual | Emerson Process Management ES30 Stereo System User Manual

Home Audio System
with Vertical CD-R/RW Player
and Digital AM/FM Receiver
OWNER'S MANUAL
ES30
Visit our web site at www.emersonradio.com
ES30_072905.p65
44
29/7/2005, 16:41
CAUT I ON
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
C AU T I O N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence
of uninsulated ‘dangerous voltage’
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE PARTS INSIDE
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
!
The exclamation point within
an equilateral triangle is intended to alert the user to
the presence of important
operating and maintenance
(ser vi ci ng) instr ucti ons in
the liter ature accompanying the appl iance.
IMPORTANT SAFETY INSTRUCTIONS
1.)
2.)
3.)
4.)
5.)
6.)
7.)
8.)
9.)
10.)
11.)
12.)
13.)
14.)
15.)
16.)
17.)
18.)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments / accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
This appliance shall not be exposed to dripping or splashing water and no object filled with
liquids such as vases shall be placed on the apparatus.
Do not overload wall outlet. Use only power source as indicated.
Use replacement parts as specified by the manufacturer.
The product may be mounted to a wall only if recommended by the manufacturer.
Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks.
1
ES30_072905.p65
1
29/7/2005, 16:41
Before We Begin
Thank you for purchasing this Emerson audio product. The Emerson brand
is your assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this
product. Please be sure to read this Owner’s Manual completely to make
sure you are getting the maximum benefit from each feature.
This product was manufactured using the highest quality components and
standards of workmanship. It was tested by Emerson inspectors and found
to be in perfect working order before it left our factory. However, there is
always the chance that some problem may occur because of rough handling
during shipment to the retail store or to the final consumer.
If, after reading this Manual, you experience any problems with the operation
of this product, please refer to the instructions for obtaining service at the
end of this Manual. Emerson and Emerson retailers are committed to your
satisfaction.
Once again, thanks for purchasing this Emerson audio product.
2
ES30_072905.p65
2
29/7/2005, 16:41
IMPORTANT NOTES
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much heat,
places lacking ventilation or dusty areas,
places subject to constant vibration and/
or humid or moist areas.
• Operate controls and switches as
described in the manual.
• Before turning ‘On’ the power, make
certain that power cord is properly
installed.
• Store your CDs, in a cool area to avoid
damage from heat.
• When moving the set, be sure to first
disconnect the power cord.
• Do not attempt to clean this unit with
chemical solvents as this might damage
the finish. Use a clean dry cloth.
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
3
ES30_072905.p65
3
29/7/2005, 16:41
PREPARATION FOR USE
Unpacking And Set Up
• Carefully remove the main unit, speakers, and remote control from the
carton, and remove all packing materials from the components.
• Remove any descriptive labels or stickers from the front panel of the
main unit. Do not remove any labels or stickers on the back panel of
the main unit or the speakers.
• Carefully remove any small strips of tape that may have been used to
hold the CD door closed during shipment.
• Unwind the AC power cord on the main unit and extend it to its full
length.
• Unwind the lead wire FM antenna on the back of the main unit and
extend it to its full length.
• Please save the carton and packing materials in case it ever becomes
necessary to return your unit for service. The original carton and packing
materials are the only way to protect your unit from damage in transit.
• Place the system on a stable, level shelf, table, desk or stand, out of
direct sunlight, convenient to a 120V 60Hz AC outlet, and away from
sources of excess heat, dust, moisture or humidity.
4
ES30_072905.p65
4
29/7/2005, 16:41
Positioning The Main Unit And Speakers
The main unit and the speakers are designed to be used on a shelf, desk, table or
stand. The main unit is shipped with two plastic legs installed for added stability
when the system is used on a flat surface. These two plastic legs allow the main
unit to “lean backward” slightly and prevent it from tipping forward when the CD
door is opened.
IMPORTANT: THESE TWO PLASTIC LEGS MUST REMAIN ON THE MAIN
UNIT FOR TABLE-TOP, DESK-TOP, OR SHELF OPERATION.
Note: If this system is to be used on a bookshelf, or inside a cabinet, be sure
to allow at least 3 inches clearance between the top of the main unit and the
shelf above the unit so that the CD door can open fully without interference. If
the CD door encounters an obstruction as it is opening, the door will close
automatically.
Do not block the ventilation openings on the top or back of the main unit.
5
ES30_072905.p65
5
29/7/2005, 16:41
Speaker Connections
Connect the speakers to the Red (+) and Black (–) terminals on right side panel of
the unit as shown below.
Press the Red (+) or Black (–) terminal tab, insert wire, release tab to hold wire in
place.
The speakers may be placed close to the main unit or as far apart as the cables
will allow. Please leave a gap of at least 1/4” between the main unit and speakers
to prevent any vibration in the speakers from causing the CD player to skip.
Note: The speakers are not magnetically shielded. They should not be placed
directly on top of, or next to, a TV set. The magnets in the speakers could
cause color distortion on the TV screen if the speakers are too close to the
TV.
The entire system may also be wall-mounted if desired. Wall-mounting
instructions can be found at the end of this manual.
6
ES30_072905.p65
6
29/7/2005, 16:41
Connecting To External Audio Sources
This system is equipped with Auxiliary Input (AUX IN) and Line Output (LINE OUT)
jacks. The Auxiliary Input Jacks allow you to listen to the sound from an external
audio source through the speakers of this system. The Line Output jacks allow
you to record from the Tuner or CD Player in this system to an external recording
device.
• Connect your playback* equipment (eg. TV, MiniDisc or cassette player) to
the AUX IN jacks on the top panel.
LINE
OUT
TV
AUX IN
• Connect your recording equipment (eg. MiniDisc or Cassette Recorder) into
the LINE OUT jacks on the top panel.
CASSETTE
RECORDER
LINE IN
LINE OUT
• Other examples of playback equipment include your TV, video recorder,DVD
player or satellite receiver, or your computer or games console.
Always refer to the equipment manufacturer’s instructions.
7
ES30_072905.p65
7
29/7/2005, 16:41
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
8
ES30_072905.p65
8
29/7/2005, 16:41
Power Source
This system is designed to operate on 120V AC 60Hz power supply only. Connecting
this system to any other power source may cause damage to the system and such
damage is not covered by your warranty.
Make sure that you connect this system to an AC outlet that is always “live”. Do not
connect this system to an AC outlet that is controlled by a wall switch.
Note: This unit has a polarized AC plug with one wide blade and one narrow
blade. This plug will only fit into a matching polarized AC outlet.
This is a safety feature to reduce the possibility of electric shock. If this plug will not
fit in your AC outlet, you probably have an outdated non-polarized outlet. You should
have your outdated outlet changed by a qualified, licensed electrician. Do not file
the wide blade on the plug, or use an adapter to make the plug fit into your outlet.
This defeats the safety feature and could expose you to electric shock.
AC Outlet
AC Plug
9
ES30_072905.p65
9
29/7/2005, 16:41
LOCATION OF CONTROLS AND INDICATORS
12
13
14 15
11
AM/FM DIGITAL TUNER
CD MICRO SYSTEM
10
26
16
9
6
7
5
4
2
3
CD TUNER MULTI FUNCTION DISPLAY
REPEAT
CLASSIC
MEMORY
ROCK
RANDOM
POP
MHz
KHz
CD
TUNER
AUX
SLEEP
REMAIN
MUTE
TIMER
A M FM
PM
STOP/BAND
1
24
25
23
14.) LINE OUT L / R Jacks.
1.) Remote Sensor.
2.)
27
17
18
19
20
21
22
8
15.) AUX IN L / R Jacks.
STOP / BAND Button.
3.)
Skip / Search Rev Button.
16.) AUX Button.
4.)
Play / Pause Button.
17.) EQ (Equalizer) Button.
5.) MODE / REMAIN Button.
18.) CD Button.
6.) TIMER / SLEEP Button.
19.) TUNER Button.
7.) MEMORY Button.
20.) VOLUME
8.) RANDOM Button.
21.)
9.) REPEAT / M-UP Button.
POWER / STANDBY Button.
22.) VOLUME
10.) CD Door.
Up Button.
Down Button.
23.) OPEN / CLOSE
11.) FM Wire Antenna.
Button.
24.) Muti-function LCD Display.
12.) AC Power Cord.
25.)
13.) RESET Button.
Skip / Search Fwd Button.
26.) SPEAKERS Terminals.
(Inside Pinhole on Back Cabinet)
27.)
PHONES Jack.
10
ES30_072905.p65
10
29/7/2005, 16:41
Remote Control
11
1.) VOLUME
Down Button.
2.) VOLUME
Up Button.
3.)
SKIP / SEARCH Rev Button.
10
4.) RANDOM Button.
5.) REPEAT / M-UP Button.
12
9
8
6.) TIMER Button.
7.) Numeric Buttons
7
8.) CD / TUNER Button.
9.) EQ (Equalizer) Button.
13
14
15
16
6
10.)
POWER Button.
5
4
3
11.) Remote Infrared Transmitter.
12.) MUTE Button.
17
18
19
2
13.) SLEEP Button.
1
14.) MEMORY Button.
15.) MODE / REMAIN Button.
16.) INTRO Button.
17.)
18.)
19.)
PLAY / PAUSE Button.
STOP / BAND Button.
SKIP / SEARCH Fwd Button.
20
20.) Battery Compartment.
(Bottom Cabinet)
11
ES30_072905.p65
11
29/7/2005, 16:41
Installing The Remote Control Batteries
The remote controller requires 2 “AAA” batteries (not included). Please use a wellknown brand of alkaline batteries for longest life and best performance.
Remove the remote control battery compartment cover by sliding the cover in the
direction of the
arrow..
Insert 2 “AAA” alkaline batteries into the compartment. Be sure to observe the
polarity markings inside the battery compartment. If the batteries are inserted
incorrectly the remote control will not operate.
The remote control must be pointed at the remote sensor on the lower part of the
front panel. The effective operating range of the remote control is approximately
15 feet. The effective operating angle is approximately 15 degrees to the left or
right of ‘dead center’.
When the operation of the remote control becomes intermittent, or the operating
range of the remote is reduced, replace the batteries.
Battery Precautions
• Replacement of batteries must be done by an adult.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
• The supply terminals are not to be short-circuited.
• Non-rechargeable batteries are not to be recharged.
• Exhausted batteries are to be removed.
• Only batteries of the equivalent type are to be used.
• Batteries are to be inserted with the correct polarity.
• Dispose of batteries properly. Do not dispose of batteries in fire. The batteries
may explode or leak.
12
ES30_072905.p65
12
29/7/2005, 16:41
OPERATING INSTRUCTIONS
• Make sure that the speakers are properly connected.
• Make sure that the FM Wire Antenna is fully extended.
• Make sure that you have installed batteries in the remote
control.
• Make sure that the AC power cord is connected to an outlet
that is always “live”. Do not connect to an outlet that is
controlled by a wall switch.
Turning The System ‘On’
Connect the unit into the 120V 60Hz AC outlet.
At the front of the unit, the light within the POWER/STANDBY
button will light
‘Red’ to indicate that the unit is in standby (Standby means plugged-in but not
switched on).
Switch the unit ‘On’by pressing the POWER/STANDBY
button on the front
panel or the remote control. The “Red” light goes ‘Off’.
The unit is now ready to use.
13
ES30_072905.p65
13
29/7/2005, 16:41
General Controls
Most of the main functions of this system can be operated by the controls on the
front panel of the main unit, or by the buttons on the remote control handset.
If a specific function can only be operated by the remote handset, or by the front
panel controls, this will be clearly indicated in the instructions.
Volume Controls
To increase or decrease the system volume press the VOLUME
or
buttons
on the front panel or the remote control.
The Volume Level Indicator will appear on the display when you change the volume
level.
The level indicator ranges
from “00” (Minimum)
to
“30” (Maximum)
The system remembers the volume level when the power is switched ‘Off’and
automatically returns to the same level when the power is switched ‘On’again.
EQ (Electronic Preset Equalizer)
The preset equalizer allows you to adjust the sound characteristic for the most
popular types of music.
Press the EQ button on the front
panel or the remote control to
cycle through the following
equalizer settings:
Flat (EQ ‘Off’), CLASSIC, ROCK or POP.
The appropriate EQ indicator appears in the display to confirm your selection. The
system remembers the EQ setting when the power is switched ‘Off’and returns to
the same setting when the power is switched ‘On’again.
14
ES30_072905.p65
14
29/7/2005, 16:41
MUTE Button (On Remote Control Only)
Press the MUTE button on the remotrol control to shut off the speakers temporarily,
for example, to answer the telephone.
The sound stops and the
“MUTE” indicator appears in the
display.
Press the MUTE button again to cancel the mute function and restore the sound.
The “MUTE” indicator disappears.
The mute function will also be canceled automatically by pressing the VOLUME
or VOLUME
buttons.
PHONES (Stereo Headphone) Jack
This system includes a stereo
PHONES jack on the right side panel of the main
unit. You may connect a set of stereo headphones, not included, to this jack for
private listening without disturbing others.
The main speakers are automatically shut ‘Off’when headphones are connected
to the
PHONES jack.
Make sure that the plug from your headphones is fully inserted into the headphone
jack. If the plug is not fully inserted the sound may be intermittent, or you may only
hear sound from one side of the headphones.
Important: To prevent hearing damage always set the volume control to a low
level before you connect the headphones. Then connect the headphones, put
them on, and very gradually increase the volume to a comfortable listening
level. Remember that CDs may contain both very soft and very loud passages.
Adjust the volume to a comfortable level using a louder passage, so that you
always know what the maximum level will be.
15
ES30_072905.p65
15
29/7/2005, 16:41
Setting The Clock
Note: The clock can be set at AUX mode, when power is ‘Off’, or at CD,
TUNER modes by pressing the MODE/REMAIN button to display the Time
mode.
1.) Depress and hold the MEMORY button on the front panel or remote control.
“24 H” will begin flashing in the display indicating that the clock is set for
“European” 24-Hour format.
Press either the
or
button to change to “American” 12-hour format if
desired.
The display will change from “24 H” to “12 H” and vice versa.
2.) Press the MEMORY button. The Hour digits will begin
flashing.
3.) Press the
or
buttons to set the display to the correct Hour,, AM or PM.
4.) Press the MEMORY button again. The Minute digits will
begin flashing.
5.) Press the
or
buttons to set the display to the correct Minute.
6.) Press the MEMORY button once more.
The colon “ : ” begins flashing and the clock starts to
run.
Notes: The correct time will always appear on the display in AUX mode and
when power is ‘Off’.
16
ES30_072905.p65
16
29/7/2005, 16:41
Listening To The Radio
1.) Press the
POWER/STANDBY button on the main unit or the remote control.
The main display turns ‘On’.
2.) If necessary, press the TUNER button on the front panel of main unit or the
CD/TUNER button on remote control to select the Tuner function.
The display will show an AM or FM station
frequency.
To select a different band, press the
STOP/BAND button.
3.) Tune to the desired frequency as follows:
• Manual Tuning
Repeatedly press the
or
buttons until the frequency of the desired
station appears on the display.
• Automatic Tuning
Press and hold the
or
buttons until the display begins to move, then
release the buttons. The tuner will search up or down the band for the next
strong station and stop on that station. Repeat this procedure until the tuner
stops on your desired station.
4.) If you tuned to an FM Stereo station the
STEREO indicator will appear in the
display.
5.) Adjust the VOLUME and EQ controls as desired.
6.) When you are finished listening press the
POWER/STANDBY button on
the main unit or remote control to return to the Standby (Power Off) mode.
The display light turns ‘Off’.
17
ES30_072905.p65
17
29/7/2005, 16:41
Hints For Better Reception
FM: The FM lead wire antenna on the back panel should be extended to its full
length. You may also have to vary the direction of this antenna until you find
the position that provides the best reception.
AM: The AM bar antenna is inside the cabinet of the main unit. You may need to
change the position of the main unit until you find the position that provides
the best reception for your favorite AM stations.
A M / F M DIGITAL T U N E R
C D M ICRO SYSTEM
C D TUNER MULTI FUNCTION DISPLAY
TUNER
KHz
AM
POP
18
ES30_072905.p65
18
29/7/2005, 16:41
Pre-setting Stations In The Tuner Memory
This system includes a 20 station preset memory. You can store up to 10 FM
stations and 10 AM stations in the tuner memory for immediate recall. The procedure
for storing stations in memory is as follows:
1.) Follow step 3 under “Listening To The Radio” in page 17 to select the first
station you wish to memorize.
Example: FM 103.5 MHz.
2.) When the desired station appears on the display press the MEMORY button
on the front panel or the remote control.
The Channel # “01” indicator
appears and the “MEMORY”
indicator flashes in the display.
3.) Press the MEMORY button on the front panel or the remote control once
more to enter the station in preset memory channel “01”.
The MEMORY indicator stops
flashing.
4.) Tune to the next station you wish to memorize. Example: FM 106.70 MHz.
Press the MEMORY button.
The “MEMORY”indicator flashes
again.
5.) Press the REPEAT/M-UP button
on the front panel or remote
control to select preset memory
channel “02”.
Then press the MEMORY button
to enter the desired station in
preset memory channel 02.
6.) Repeat steps 4 and 5, selecting a different preset memory channel number
each time, until you have entered up to 10 FM stations in the tuner memory.
7.) Press the STOP/BAND button to select the AM band and follow the same
procedure to enter up to 10 AM stations in the tuner memory.
19
ES30_072905.p65
19
29/7/2005, 16:41
Recalling Preset Stations
1.) Turn the unit ‘On’, press the
STOP/BAND button to select the desired band.
2.) Press the REPEAT/M-UP button on the front panel or the remote control
repeatedly to scroll through the preset memories until the display shows the
desired station.
3.) You may also use the number buttons on the remote control to directly select
the desired preset memory number.
Simply press the corresponding number key on the remote handset to select
preset memory numbers 1 through 0 (10).
Changing Preset Stations
To change any preset station memory:
1.) Select the desired band and tune to the new station you wish to memorize.
2.) Press the MEMORY button and then press the REPEAT/M-UP button to display
the memory number you wish to change.
3.) Press the MEMORY button again to enter the new station in the memory. The
new station is memorized and the previous station is deleted from the memory.
20
ES30_072905.p65
20
29/7/2005, 16:41
Playing Compact Discs
Important: This CD player can play normal CDs plus CD Recordable (CD-R)
and CD ReWritable (CD-RW) discs. However the playability of CD-R/RW discs
may be affected by the type of software that was used in ‘ripping’ the tracks
from the original discs and ‘burning’the tracks onto the blank media. Playability
may also be affected by the quality and condition of the blank media you use
for recording. 100% compatibility cannot be guaranteed. This is not an
indication of any problems with your player.
Caution!!
Never open or close the CD door rapidly by hand - doing so will damage the
mechanism.
In an emergency situation (eg. An AC power failure) where you have no option
other than to open or close the door by hand, do so very slowly and very gently.
APPLY ONLY LIGHT PRESSURE - NEVER USE FORCE ON THE DOOR.
21
ES30_072905.p65
21
29/7/2005, 16:41
Normal Playback
1.) Press the
POWER/STANDBY button to turn the system ‘On’.
2.) Press the CD button on front panel or CD/TUNER button on remote control to
select CD function.
3.) Press the OPEN/CLOSE
button on front panel to open the CD door. Remove
the “dummy CD” transit protection cards and discard it. You cannot play your
own CD unless the card is removed.
4.) Load your own CD into the player with the printed ‘label’facing out.
Gently press on the CD near the center hole to insure that the disc is properly
‘seated’on the spindle.
AM/FM DIGITAL TUNER
C D M I C R O SYSTEM
CD TUNER MULTI FUNCTION DISPLAY
5.) Press the OPEN/CLOSE
REPEAT
CLASSIC
MEMORY
ROCK
RANDOM
POP
CD
MHz
KHz
AM FM
PM
MUTE
TUNER
AUX
SLEEP
REMAIN
TIMER
X-BASS
button to close the CD door.
The display flashes as the player reads the
Table Of Contents on the disc.
After reading the disc the display will show the
total tracks and playing time.
Note: The reading time may be longer if you are using CD-RW (rewritable)
discs. This is normal and not an indication of any problem with your unit.
6.) Press the
playback.
PLAY/PAUSE button to begin
7.) Adjust the VOLUME and EQ controls as desired.
8.) Playback will continue until all tracks on the disc have been played, then the
player stops and the display shows the total tracks number and playing time on
the disc.
22
ES30_072905.p65
22
29/7/2005, 16:41
9.) To stop playback at any time, press the
STOP/BAND button.
10.) If you are finished listening, press the OPEN/CLOSE
button to open the
CD door, remove your disc from the player, re-close the door and press the
POWER/STANDBY button to return the system to the Standby (Off) mode.
Pause Control
To pause temporarily during CD playback press the
PLAY/PAUSE button again.
The sound stops and the elapsed time flashes in
the display, but the disc continues spinning.
Press the
PLAY/PAUSE button once more to cancel Pause mode and resume
playback at the same point, the elapsed time stops flashing.
Skip Track and High Speed Music Search
• During playback, repeatedly press the
or
buttons to skip to higher or
lower numbered tracks. Playback will begin on the selected track.
• During playback, depress and hold the
or
buttons to search within a
track at high speed to locate a specific musical passage.
Release the
or
buttons when you hear the desired passage. Normal
speed playback will resume at that point.
23
ES30_072905.p65
23
29/7/2005, 16:41
Repeat Playback
You can program the player to continuously repeat a single track or the entire disc.
The Repeat function can be activated while a disc is playing or while the disc is
stopped.
One Track Repeat
Press the
or
button until the desired track number appears in the display,
then press the REPEAT/M-UP button once.
The REPEAT indicator ‘flashes’ in the
display. Press the
PLAY/PAUSE button
to begin playback on that track.
The selected track will be repeated continuously.
All Tracks Repeat
Load the disc as usual and wait until the total playing time and track numbers
appear on the display. Press the REPEAT/M-UP button twice.
The REPEAT indicator remains ‘On’. Press
the PLAY/PAUSE
button to begin
playback.
The entire disc will be repeated continuously.
To cancel Repeat Playback continue pressing the REPEAT/M-UP button until the
REPEAT indicator disappears. Repeat is also canceled by opening the CD Door
or switching to Tuner function.
24
ES30_072905.p65
24
29/7/2005, 16:41
Random Playback
This feature allows you to play all the tracks on a disc in random order.
Load the disc as usual and wait until the display shows the total playing time and
number of tracks. Press the RANDOM button.
The RANDOM indicator appears in the
display.
The tracks will be played in random order. After all tracks have played the player
stops and the display again shows the total playing time and number of tracks.
To cancel the Random mode press the RANDOM button until the RANDOM
indicator disappears. Random mode can also be canceled by pressing the STOP/
BAND button.
Intro Scan Playback (Remote Control Only)
This feature allows you to play just the first 10 seconds of each track on the disc.
This may be useful when you are trying to locate a specific song but you do not
remember the title.
Load the disc as usual and wait until the display shows the total playing time and
number of tracks. Press the INTRO button on the remote control.
The INTRO indicator will appear in the
display.
The player will play the first 10 seconds of each track automatically. When the first
10 seconds of the last track has played the player stops and the display again
shows the total playing time and number of tracks on the disc.
To cancel the Intro playback mode before the disc ends press the INTRO button
on the remote control once more until the INTRO indicator disappears. The player
will continue normal playback.
Intro mode can also be canceled by pressing the
the CD Door, or switching to the Tuner function.
STOP/BAND button, opening
25
ES30_072905.p65
25
29/7/2005, 16:41
Programmed Playback
You can program up to 20 tracks on a disc to playback in any desired order. You
may also program a specific track to play several times within the same program.
Note: The player cannot be programmed while a disc is playing. If a disc is
playing press the
STOP/BAND button to stop playback before you begin
the programming steps below.
1.) Press the CD/TUNER button on the remote control or CD button on front panel
to select CD mode. Insert your disc in the player, close the door, and wait until
the total track number and play time appear in the display.
2.) Press the MEMORY button once.
The MEMORY Indicator
flashes and program memory
“P- 01”, Track “01” appears
in the display.
3.) Use the
or
buttons to select the first track to be programmed.
Example: Track “07”.
4.) When track number “07” appears in the display, press the MEMORY button
once again to enter the track “07” in program memory number “01”.
The track number returns to
“0 0 ” a n d t h e p r o g r a m
memory advances to “P- 02”
indicating that you may now select a track to be entered in program memory
number “02”.
5.) Use the
or
buttons to select the next track to be programmed. When
the desired track number appears in the display press the MEMORY button
again to enter that track in the program memory.
6.) Repeat Step 5 until you have entered up to 20 tracks in the program memory.
26
ES30_072905.p65
26
29/7/2005, 16:41
7.) To begin programmed playback press the
PLAY/PAUSE button.
The display will show the first
programmed track and
playback will begin on that
track. The MEMORY Indicator stops flashing and remains in the display.
After the last programmed track has played the player stops but the programmed
tracks remain in the memory.
To play the programmed tracks again, press the MEMORY button and then the
PLAY/PAUSE button.
To cancel the programmed sequence from memory, press the
button at programming mode or open the CD door.
STOP/BAND
Program Repeat Playback
You can use the Program and Repeat features together to continuously repeat a
programmed sequence of tracks.
First, program the desired tracks according to Steps 1 through 7 on the previous
page.
When Programmed Playback begins press the REPEAT/M-UP button twice to
activate the All Tracks Repeat feature.
The REPEAT Indicator appears
in LCD display and all the tracks
in your programmed sequence
will be repeated continuously.
To cancel Programmed Repeat Playback press the
both the MEMORY and REPEAT Indicators go ‘Off’.
STOP/BAND button until
27
ES30_072905.p65
27
29/7/2005, 16:41
Timer Function
This system includes a programmable Timer function that will turn the system
‘On’, play for one hour, and then shut the system ‘Off’automatically. You can use
the timer to wake you up to the Radio or to your favorite CD. The timer can be
programmed while the system is in the Standby (Power Off) mode, the Aux mode,
Tuner mode, or the CD mode.
To Set The Turn ‘On’ Time
1.) Press and hold the TIMER/SLEEP button on the front panel or press the TIMER
button on the remote control once.
The “12:00 AM ” appears and the TIMER
indicator begins ‘flashing’in the display.
Press and hold the MEMORY button for at
least 3 seconds. The Hour digits begin to flash.
2.) Press the
or
button on the front panel or the remote control to set the
display to the desired turn ‘On’hour, AM or PM.
3.) Press the MEMORY button. The Minute digits
begin flashing.
4.) Press the
or
buttons on the front panel of the main unit or the remote
control to set the display to the desired turn ‘On’minute.
5.) Press the MEMORY button once more to enter
the turn ‘On’time in the memory.
After a few seconds the TIMER display stops
flashing and remains ‘On’ and the display
returns to the correct time, Tuner display, or
the CD display.
28
ES30_072905.p65
28
29/7/2005, 16:41
6.) At the selected ‘On’ time the system will turn ‘On’ automatically to the last
function selected, either Tuner or CD.
The TIMER indicator flashes.
It will play for one hour and then shut ‘Off’automatically.
Note: If the system turns on to CD function it will only play until the end of the
disc and then stop.
As long as the TIMER indicator remains in the display the timer will turn the system
on every day at the same time.
• To ‘deactivate’the timer press and hold the TIMER/SLEEP button on the front
panel or press the TIMER button on the remote control once. The TIMER
indicator disappears from the display.
• To ‘reactivate’the timer press and hold the TIMER/SLEEP button on the front
panel or press the TIMER button on the remote control once until the TIMER
indicator reappears in the display.
29
ES30_072905.p65
29
29/7/2005, 16:41
Sleep Timer
This system includes a programmable Sleep Timer that allows you to fall asleep to
between 90 and 10 minutes of music and then shuts the power ‘Off’automatically.
To Operate The Sleep Timer:
1.) Turn the system ‘On’and operate either the Tuner or CD function as usual.
2.) Adjust the VOLUME controls to the desired level. Remember that the level
you select for the sleep to music function is the same level you will hear when
the timer turns the system on in the morning.
3.) Press the SLEEP button on the front panel or the remote control once.
4.) The display will show “90” indicating that the sleep timer will shut the power
‘Off’after 90 minutes.
The SLEEP indicator begins flashing.
Continue pressing the SLEEP button to decrease the amount of sleep timer
operation. Each time you press the SLEEP button you reduce the sleep time
by 10 minutes.
Release the SLEEP button when the display shows the desired amount of
Sleep timer operation.
5.) After a few seconds the Sleep Time display
disappears and the SLEEP indicator
remains ‘On’.
When the Sleep Timer counts down to “00”, the power shuts ‘Off’automatically.
Notes:
• You can shut the unit off manually before the Sleep Timer counts down to
“00” by pressing the
POWER/STANDBY button at any time.
• Remember that if you are falling asleep to CD you will also wake to CD,
and if you fall asleep to the Tuner you will also wake to the Tuner.
• If you are falling asleep to CD, the system will only operate until the CD
ends. If you set the Sleep Timer for 90 minutes but your CD is only 45
minutes long, the music will stop after 45 minutes.
30
ES30_072905.p65
30
29/7/2005, 16:41
MODE/REMAIN Button
Normally the display shows the correct time in the Aux mode, Standby (Power Off)
mode, the radio frequency in the Tuner mode, and the CD track and time information
in the CD mode.
You can press the MODE/REMAIN button repeatedly to show the following
information on the display:
• In STANDBY (Power Off) Mode:
Correct Time
TIMER ‘On’Time
Correct Time.
TIMER ‘On’Time
Correct Time.
• AUX Mode:
Correct Time
• In TUNER Mode:
Radio Frequency
Correct Time
TIMER ‘On’Time
Radio Frequency..
• In CD Playback Mode:
CD Elapsed Time
Time
CD Remaining Time
Correct Time
CD Elapsed Time.
31
ES30_072905.p65
31
29/7/2005, 16:41
TIMER ‘On’
Auxiliary Operation (On Front Panel Only)
To listen to an auxiliary audio source connected to the AUX IN R/L jacks on the top
panel of this unit (refer to page 8).
Press the AUX button on front panel to select the Aux function.
The AUX indicator appears in the display.
Operate the external device as you would normally.
When you hear the music from your external source adjust the VOLUME and EQ
controls of this system as desired.
32
ES30_072905.p65
32
29/7/2005, 16:41
Resetting The System Computer
This system is equipped with a special circuit designed to protect the internal
computer from permanent damage due to unexpected power surges.
If you find that the system does not respond to any commands from the front panel
controls or the remote handset, the system probably experienced a sudden power
surge that activated the protection circuit.
To reset the system after a power surge use the point of a pencil, a toothpick, a
straightened paper-clip or similar object to press the RESET button which is located
in a small opening on the back of unit.
The system will return to the Standby (Power Off) mode.
Note: Resetting the system computer also clears all of the system memory
and returns the system to its original factory default settings. All of the preset
tuner memories, the clock and the timer settings will be erased after you press
the RESET button.
It will be necessary to re-enter the stations in the tuner preset memories,
reset the clock and the timer settings.
33
ES30_072905.p65
33
29/7/2005, 16:41
WALL MOUNTING INSTRUCTIONS
Note: The plastic legs must be removed from the main unit before wall
mounting. To remove the legs, slide them downward as shown.
To re-attach the legs, slide the U-shaped cut-outs in the legs upwards over the
round posts at the back of the unit. Make sure the legs are pushed up all the way.
If you decide to wall mount your ES30 audio system please read and
carefully follow these instructions:
Note: Wall mounting hardware is not included.
You should purchase the appropriate type of anchors for the wall where the
unit will be mounted. (Solid-wall, Hollow-wall, etc.) Wall anchors are available
at hardware stores and home improvement centers. Tools required: Electric
drill, Hammer, Screwdriver.
34
ES30_072905.p65
34
29/7/2005, 16:41
General Precautions and Recommendations
• When choosing a location for wall mounting remember that the main unit must
be connected to an AC outlet. The AC power cord of the main unit should be
able to hang straight down from the main unit to the AC outlet.
(See Figure 1.)
AM/FM DIGITAL TUNER
CD MICRO SYSTEM
AM/FM DIGITAL TUNER
CD MICRO SYSTEM
CD TUNER MULTI FUNCTION DISPLAY
CD TUNER MULTI FUNCTION DISPLAY
REPEAT
CLASSIC
ROCK
MHz
KHz
C D
A M FM
T U N E R
AUX
SLEEP
REMAIN
REPEAT
CLASSIC
ROCK
MHz
KHz
C D
A M FM
T U N E R
AUX
SLEEP
REMAIN
MEMORY
MEMORY
R A N D O M
POP
P M
MUTE
R A N D O M
TIMER
POP
P M
MUTE
TIMER
Incorrect
Correct
Figure 1.
Connect the main unit to the AC outlet and position it against the wall in your
desired location. Make sure that the plug remains firmly and full inserted into the
outlet. There should be just enough slack in the power cord so that the plug can be
easily removed from, and reconnected to the AC outlet.
• Have someone hold the main unit against the wall in the desired location and
make a pencil mark on the wall to indicate center point of the top edge of the
cabinet.
Pencil Mark At Center
A M / F M D IG I T A L T U N E R
CD MICRO SYSTEM
C D T U N E R M U L T I FUN C T I O N D I S P L A Y
REPEAT
MEMORY
RANDOM
CLASSIC
ROCK
POP
MHz
KHz
CD
TUNER
AUX
SLEEP
REMAIN
MUTE
TIMER
A M FM
PM
35
ES30_072905.p65
35
29/7/2005, 16:41
• If there is no AC outlet directly below the desired mounting location you may
use a UL approved extension cord. In this case you should allow the AC plug
of the main unit to reach all the way to the floor and connect the extension cord
on the floor, not above the floor. (See Figure 2.)
AM/FM DIGITAL TUNER
CD MICRO SYSTEM
AM/FM DIGITAL TUNER
CD MICRO SYSTEM
CD TUNER MULTI FUNCTION DISPLAY
CD TUNER MULTI FUNCTION DISPLAY
REPEAT
CLASSIC
MHz
C D
T U N E R
AUX
SLEEP
REMAIN
REPEAT
KHz
MEMORY
R A N D O M
ROCK
POP
A M FM
P M
MUTE
CLASSIC
ROCK
MHz
KHz
C D
A M FM
TUNER
AUX
SLEEP
REMAIN
MEMORY
R A N D O M
TIMER
POP
P M
MUTE
TIMER
Incorrect
Correct
Figure 2.
• Although all major functions of this system can be operated by the remote
control, you must still load and unload your CD manually. Therefore the main
unit should be mounted at a height that is convenient and comfortable for
changing discs.
Important: The front cover requires 3" clearance to open fully. If you plan to
mount the unit under a shelf, in a cabinet. etc, you must allow at least 3"
clearance above the unit so that the door can open completely without
obstruction.
If the front cover encounters some obstruction as it is opening, the motor will
reverse automatically and the door will close immediately.
36
ES30_072905.p65
36
29/7/2005, 16:41
Template Instructions
1.) Select the desired location for wall mounting after carefully reviewing the
"General Precautions and Recommendations" of the wall mounting
instructions.
2.) Tape the template to the wall, or other surface, in the desired location. Align
the top edge of the template with the pencil mark you made on the wall. Be
sure to allow at least 3" clearance above the main unit, for the CD door to open
fully.
3.) Make sure that the template is level.
4.) Use an awl, ice pick, a nail or similar pointed tool, and push through the template
to make a small starter hole in the wall surface as indicated by the
"Drill Hole Here" marks. Then remove the template from the wall.
5.) Before You Drill: Make sure that there are no water pipes, gas pipes,
electrical wires on other obstructions or hazards behind the wall in your
chosen mounting location. If you are not sure about this and don't know
how to check, perhaps you should consider having the system mounted
by someone with the necessary experience.
6.) Make sure that you are using the correct type of anchors for your wall.
• If the wall material is Sheetrock® (sometimes called wall-board, gypsum-board,
or plaster-board) you can use plastic ‘hollow-wall anchors’.
• If your wall is solid plaster, concrete, brick, or similar solid material, use the
appropriate type of ‘solid-wall anchors’.
• If your wall is solid wood, you may be able to use round-head wood screws
without anchors.
Important: If you have no experience installing wall anchors you should have
this system mounted by someone who does have the proper experience.
Whichever type anchors you use, make sure that the diameter of the screw
heads is at least 1/4”.
Follow the instructions supplied with the wall anchors to determine the proper size
drill bit to use in your electric drill. After installing the proper size bit, drill holes in
the wall surface at the 4 locations where you made the starter holes in Step 4.
37
ES30_072905.p65
37
29/7/2005, 16:41
7.) Insert the tip of the anchor into each hole and use a hammer to tap the anchors
all the way in until they are flush with the wall surface.
Anchor
Wall Surface
8.) Insert the screw into the anchor and tighten the screw until it touches the collar
on the anchor. This causes the anchor to spread inside the wall and locks the
anchor in place.
9.) Loosen the screw until there is a gap about 1/8" between the screw head and
the wall.
1/8” Gap
38
ES30_072905.p65
38
29/7/2005, 16:41
10.) Position the main unit over the two screw heads so that the heads of the
screws fit into bottom of each "Keyhole" on the back cabinet. When the two
screw heads are inside the keyholes, slide the main unit slightly downward
until each screw head is in the top of the keyhole.
Insert Screw Head
Into Keyhole.
Slide Unit Downward
To Lock Unit In Position.
If the main unit is still loose, you probably left too large a gap between the screw
head and the wall. Slide the unit slightly upward and take it off the mounting screws.
Tighten one or both screws slightly and remount the unit. It should fit snugly against
the wall and not move when you are loading or unloading CD.
Follow a similar procedure to mount each speaker.
Notes:
• It will be necessary to remove the main unit from the wall to connect the
speaker wires. If there is any excess speaker wire hanging between the
main unit and the speakers, remove the speaker from the wall and use a
twist-tie to secure the excess wire to the lower metal bracket on the back of
the speaker cabinet, then remount the speakers.
• You can also purchase plastic cord covers at most home improvement
centers. These covers can easily be cut to any desired length and attached
to the wall to conceal the speaker wires and AC power cord if necessary.
The covers can also be painted or wall papered to match the surrounding
wall surface.
39
ES30_072905.p65
39
29/7/2005, 16:41
CARE AND MAINTENANCE
Compact Disc Care
• To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
• Fingerprints and dust should be carefully wiped off the disc’s recorded surface
with a soft cloth.Unlike conventional records, compact discs have no grooves
to collect dust and microscopic debris, so gently wiping with a soft cloth should
remove most particles. Wipe in a straight line from the inside to the outside of
the disc. Small dust particles and light stains will have absolutely no effect on
reproduction quality.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• Never write on or affix labels to the surface of compact discs.
Care Of The Cabinet
If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax,
polish sprays, or abrasive cleaners on the cabinet.
Caution
Never allow any water or other liquids to get inside the unit while cleaning.
40
ES30_072905.p65
40
29/7/2005, 16:41
R
SERVICE
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
CENTER PERMITTED TO PERFORM
WARRANTY...
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
5101 Statesman Drive,
Irving, TX 75063.
41
ES30_072905.p65
41
29/7/2005, 16:41
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.,
5101 Statesman Drive,
Irving, TX 75063.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
The serial number of your system is located on a label on the back panel. Please
take a moment now to locate the serial number and write the number in the space
provided below. You may be asked to provide this number when calling for product
service.
Model Number: ES30
Serial Number:
42
ES30_072905.p65
42
29/7/2005, 16:41
R
EMERSON
Part No. 16-3000
508-02
ES30_072905.p65
Printed in China
43
29/7/2005, 16:41
Download PDF

advertising