AC Power
For Business-Critical Continuity™
Liebert® NXL™ Maintenance Bypass Cabinet
Installation Manual – 250-400kVA, 60Hz
CONTACTING LIEBERT FOR SUPPORT
To contact Emerson Network Power Liebert Services for information or repair service in the United
States, call 1-800-LIEBERT (1-800-543-2378). Liebert Services offers a complete range of start-up
services, repair services, preventive maintenance plans and service contracts.
For repair or maintenance service outside the 48 contiguous United States, contact Liebert Services,
if available in your area. For areas not covered by Liebert Services, the authorized distributor is
responsible for providing qualified, factory-authorized service.
For Liebert Services to assist you promptly, have the following information available:
Part Numbers: ________________________________________________________________
Serial Numbers: _______________________________________________________________
kVA Rating: __________________________________________________________________
Date Purchased: _______________________________________________________________
Date Installed: ________________________________________________________________
Location: _____________________________________________________________________
Input Voltage/Frequency: ______________________________________________________
Output Voltage/Frequency: _____________________________________________________
Product Warranty Registration
To register for warranty protection, visit the Service and Support section of our Web site at:
www.liebert.com
Click on Product Registration and fill out the form.
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.0
SINGLE-MODULE MECHANICAL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2
Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3
Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.1
1.3.2
1.4
Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4.1
1.4.2
1.4.3
Moving the Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Floor Installation/Anchoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.5
Cable Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.6
Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6.1
Power Cable Connection Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0
INSTALLATION DRAWINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3.0
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
i
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Cabinet arrangement—Liebert NXL UPS, battery cabinets, maintenance bypass cabinet. . . . . . 4
Two-Breaker Maintenance Bypass Cabinet, one-input, attached . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Two-Breaker Maintenance Bypass Cabinet, two-input, attached . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Two-Breaker Maintenance Bypass Cabinet, three-input, attached or detached . . . . . . . . . . . . . . 8
Liebert NXL Maintenance Bypass Cabinet—250 and 300kVA main component location . . . . . . . 9
Liebert NXL Maintenance Bypass Cabinet—400kVA main component location . . . . . . . . . . . . . 10
Liebert NXL Maintenance Bypass Cabinet—250 and 300kVA outline drawing . . . . . . . . . . . . . 11
Liebert NXL Maintenance Bypass Cabinet—400kVA outline drawing. . . . . . . . . . . . . . . . . . . . . 12
Liebert NXL Maintenance Bypass Cabinet—250 and 300kVA terminal details . . . . . . . . . . . . . 13
Liebert NXL Maintenance Bypass Cabinet—400Kva terminal details . . . . . . . . . . . . . . . . . . . . . 14
Cable routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Liebert NXL Maintenance Bypass Cabinet, one-input system, point-to-point wiring
to UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Liebert NXL Maintenance Bypass Cabinet, two-input system, point-to-point wiring
to UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Liebert NXL Maintenance Bypass Cabinet, three-input system, point-to-point wiring
to UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Liebert NXL Maintenance Bypass Cabinet Control wire diagram without interlock . . . . . . . . . 22
Liebert NXL Maintenance Bypass Cabinet control wire diagram with interlock. . . . . . . . . . . . . 23
Liebert NXL Maintenance Bypass Cabinet control wire routing. . . . . . . . . . . . . . . . . . . . . . . . . . 24
Ground strap location for connected cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Liebert-supplied interconnect wiring for one-input Liebert NXL Maintenance
Bypass Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert-supplied interconnect wiring for two-input Liebert NXL Maintenance
Bypass Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert-supplied interconnect wiring for three-input Liebert NXL Maintenance
Bypass Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control wiring connections without interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control wiring connections with interlock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert NXL Maintenance Bypass Cabinet specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert NXL Maintenance Bypass Cabinet current ratings—System Input . . . . . . . . . . . . . . . .
Liebert NXL Maintenance Bypass Cabinet current ratings—System Output . . . . . . . . . . . . . . .
Recommended conduit and cable sizes—Maintenance Bypass Input . . . . . . . . . . . . . . . . . . . . . .
Recommended conduit and cable sizes—Rectifier Input (1-Input System) . . . . . . . . . . . . . . . . . .
Recommended conduit and cable sizes—Module Bypass Input . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended conduit and cable sizes—Module Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended conduit and cable sizes—Load Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended conduit and cable sizes—Load Bank Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended lug sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
17
19
21
22
23
26
27
27
27
27
28
28
28
28
29
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation of your
Liebert NXL™ Maintenance Bypass Cabinet.
! WARNING
Exercise extreme care when handling cabinets to avoid equipment damage or injury to
personnel. The Liebert NXL Maintenance Bypass Cabinet weight ranges from 700 to 900 lb
(317 to 409kg).
Locate center of gravity symbols
and determine unit weight before handling each
cabinet. Test lift and balance the cabinets before transporting. Maintain minimum tilt from
vertical at all times.
Slots at the base of the cabinets are intended for forklift use. Base slots will support the unit
only if the forks are completely beneath the unit.
In case of fire involving electrical equipment, use only carbon dioxide fire extinguishers or
those approved for use in fighting electrical fires.
Extreme caution is required when performing maintenance.
Be constantly aware that the system contains high DC as well as AC voltages.
Check for voltage with both AC and DC voltmeters prior to making contact.
Read this manual thoroughly before working with the maintenance bypass cabinet. Retain this manual for use by installing personnel.
! WARNING
Under typical operation and with all doors closed, only normal safety precautions are
necessary. The area around the system should be kept free of puddles of water, excess
moisture and debris.
Special safety precautions are required for procedures involving handling, installation and
maintenance of the Maintenance Bypass Cabinet. Observe all safety precautions in this
manual before handling or installing the Maintenance Bypass Cabinet. Observe all
precautions in the Operation and Maintenance Manual, before as well as during performance
of all maintenance procedures.
This equipment contains circuits that are energized with high voltage. Only test equipment
designed for troubleshooting should be used. This is particularly true for oscilloscopes. Always
check with an AC and DC voltmeter to ensure safety before making contact or using tools.
Even when the power is turned Off, dangerously high potential electric charges may exist.
All power and control wiring should be installed by a qualified electrician. All power and
control wiring must comply with the NEC and applicable local codes.
ONLY properly trained and qualified personnel should perform maintenance on the Maintenance
Bypass Cabinet. When performing maintenance with any part of the equipment under power,
service personnel and test equipment should be standing on rubber mats. The service personnel
should wear insulating shoes for isolation from direct contact with the floor ground.
One person should never work alone, even if all power is removed from the equipment. A
second person should be standing by to assist and summon help in case of an accident.
! CAUTION
This unit complies with the limits for a Class A digital device, pursuant to Part 15 Subpart J
of the FCC rules. These limits provide reasonable protection against harmful interference in a
commercial environment. This unit generates, uses and radiates radio frequency energy and,
if not installed and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this unit in a residential area may cause
harmful interference that the user must correct at his own expense.
NOTE
Liebert Corporation neither recommends nor knowingly sells this product for use with life
support or other FDA-designated “critical” devices.
1
Single-Module Mechanical Installation
1.0
SINGLE-MODULE MECHANICAL INSTALLATION
1.1
Introduction
This section describes the requirements that must be taken into account when planning the positioning and cabling of the Liebert NXL Maintenance Bypass Cabinet.
This chapter is a guide to general procedures and practices that should be observed by the installing
engineer. The particular conditions of each site will determine the applicability of such procedures.
! WARNING
Do not apply electrical power to the UPS equipment before the arrival of the commissioning
engineer.
! WARNING
The Maintenance Bypass Cabinet should be installed by a qualified engineer in accordance
with the information contained in this chapter and all equipment not referred to this manual
is shipped with details of its own mechanical and electrical installation.
! WARNING
Eye protection should be worn to prevent injury from accidental electrical arcs. Remove rings,
watches and all metal objects. Only use tools with insulated handles. Wear rubber gloves.
NOTICE
Three-phase input supply required.
The standard Liebert NXL UPS is suitable for connection to three-phase, four-wire (+ Earth)
TN-C, TN-S, IT-G, IT-IG or three-phase, three-wire plus ground, IT-UG.
If using the Liebert NXL UPS with an IT Power system, a four-pole disconnect device must be
included as part of building installation.
1.2
Preliminary Checks
Before installing the Maintenance Bypass Cabinet, carry out the following preliminary checks:
• Visually examine the equipment for transit damage, both internally and externally. Report any
damage to the shipper immediately.
• Verify that the correct equipment is being installed. The equipment supplied has an identification
tag on the back of the main door reporting: the type, size and main calibration parameters of the
UPS.
• Verify that the room satisfies the environmental conditions stipulated in the equipment specifications, paying particular attention to the ambient temperature and air exchange system.
1.3
1.3.1
Environmental Considerations
Room
The Maintenance Bypass Cabinet is intended for indoor installation and should be located in a cool,
dry, clean-air environment with adequate ventilation to keep the ambient temperature within the
specified operating range (see 3.0 - Specifications).
All models of the Liebert NXL Maintenance Bypass Cabinet are convection-cooled. To permit air to
enter and exit and prevent overheating or malfunctioning, do not cover the ventilation openings.
When bottom entry is used, the conduit plate can be removed and punched and replaced. The bottom
conduit plate must be replaced for proper airflow. If necessary to cool the room, install a system of
room extractor fans.
NOTE
The Maintenance Bypass Cabinet is suitable for mounting on concrete or other noncombustible surface only.
2
Single-Module Mechanical Installation
1.3.2
Storage
Should the equipment not be installed immediately, it must be stored in a room for protection against
excessive humidity and or heat sources (see Table 6).
1.4
Positioning
The cabinet is structurally designed to handle lifting from the base.
Access to the power terminals, auxiliary terminals blocks and power switches is from the front.
The top and front removable panels are secured to the chassis by screws. The door can be opened to
give access to the power connections bars, auxiliary terminal blocks and power isolators. Front door
can be opened at 180° for better Service and more flexibility in installations.
1.4.1
Moving the Cabinets
The route to be travelled between the point of arrival and the unit’s position must be planned to make
sure that all passages are wide enough for the unit and that floors are capable of supporting its
weight (for instance, check that doorways, lifts, ramps, etc. are adequate and that there are no
impassable corners or changes in the level of corridors).
Ensure that the cabinet weight is within the designated surface weight loading (kg/cm2) of any handling equipment. See Table 6 for weight.
Ensure that any lifting equipment used in moving the cabinet has sufficient lifting capacity.
The Maintenance Bypass Cabinet can be handled by means of a fork lift or similar equipment. For
operations with a fork lift, refer to installation drawings in 2.0 - Installation Drawings.
Because the weight distribution in the cabinet is uneven, use extreme care during handling and
transporting.
When moving the unit by forklift, care must be taken to protect the panels. Do not exceed a 15-degree
tilt with the forklift. Bottom structure will support the unit only if the forks are completely beneath
the unit.
Handling the unit with straps is not authorized.
! CAUTION
Take extreme care when handling Maintenance Bypass Cabinets to avoid equipment damage
or injury to personnel.
1.4.2
Clearances
Liebert NXL Maintenance Bypass Cabinets have no ventilation grilles at either side or at the rear.
Clearance around the front of the equipment should be sufficient to enable free passage of personnel
with the doors fully opened. It is important to leave a distance of 24" (610mm) between the top of the
cabinet and any overhead obstacles to permit adequate circulation of air coming out of the unit.
1.4.3
Floor Installation/Anchoring
The installation diagrams in 2.0 - Installation Drawings of this manual identify the location of the
holes in the base plate through which the equipment can be bolted to the floor. If the equipment is to
be located on a raised floor it should be mounted on a pedestal suitably designed to accept the equipment point loading. Refer to the base view to design this pedestal.
1.5
Cable Entry
Cables can enter the Maintenance Bypass Cabinet from the bottom or top.
3
Single-Module Mechanical Installation
1.6
Power Cables
The Maintenance Bypass Cabinet requires both power and control cabling once it has been mechanically installed. All control cables must be separate from the power cables. Run control cables in metal
conduits or metal ducts that are electrically bonded to the cabinets they are connected to.
The cable design must comply with the voltages and currents provided in Tables 7 and 8, follow local
wiring practices and take into consideration the environmental conditions (temperature and physical
support media).
For cable entry terminal, refer to Figure 9.
! WARNING
Before cabling up the cabinet, ensure that you are aware of the location and operation of the
external isolators that connect the input/bypass supply.
Check that these supplies are electrically isolated, and post any necessary warning signs to
prevent their inadvertent operation.
The following are guidelines only and superseded by local regulations and codes of practice where
applicable:
• Take special care when determining the size of the neutral cable (grounded conductor), because
current circulating on the neutral cable may be greater than nominal current in the case of nonlinear loads. Refer to Tables 7 and 8.
• The grounding conductor should be sized according to the fault rating, cable lengths, type of protection, etc. The grounding cable connecting the UPS to the main ground system must follow the
most direct route possible.
• Consider using smaller, paralleled cables for heavy currents as a way of easing installation.
Figure 1
Cabinet arrangement—Liebert NXL UPS, battery cabinets, maintenance bypass cabinet
Liebert
NXL
UPS
Additional
Battery
Cabinet(s)
Additional
Battery
Cabinet(s)
Battery
Cabinet
Liebert
NXL
UPS
Maintenance
Bypass
Cabinet
Battery
Cabinet
Liebert
NXL
UPS
Liebert
NXL
UPS
Liebert
NXL
UPS
4
Note: If a maintenance bypass
cabinet is used, it must be
installed on the right side of
the Liebert NXL UPS
Maintenance
Bypass
Cabinet
Battery
Cabinet
Additional
Battery
Cabinet(s)
Single-Module Mechanical Installation
1.6.1
Power Cable Connection Procedure
The system input, UPS bypass, UPS output and system output cables (all require lug type terminations) are connected to busbars situated behind the power isolator switches as shown in 2.0 - Installation Drawings. These are accessible when the power compartment door is opened.
Equipment Ground
The equipment ground busbar is located near the input and output power supply connections as
shown in 2.0 - Installation Drawings. The grounding conductor must be connected to the ground
busbar.
All cabinets and cable trunking should be grounded in accordance with local regulations.
! WARNING
Failure to follow adequate grounding procedures can result in electric shock hazard to
personnel, or the risk of fire, should an ground fault occur.
! WARNING
The operations described in this section must be performed by authorized electricians or
qualified technical personnel. If you have any difficulties, do not hesitate to contact Emerson
Network Power Liebert Services. See the back page of this manual for contact information.
NOTE
Proper grounding considerably reduces problems in systems caused by electromagnetic
interference.
5
Single-Module Mechanical Installation
Once the equipment has been finally positioned and secured, connect the power cables as described in
the following procedure.
Refer to the appropriate cable connection drawing in 2.0 - Installation Drawings.
1. Verify that the bypass equipment is isolated from its external power source and all the power
isolators are open. Check that these supplies are electrically isolated and post any necessary
warning signs to prevent their inadvertent operation.
2. Open the door to the cabinet and remove the interior panels.
3. Connect the ground and any necessary main bonding jumper to the equipment ground busbar.
NOTE
The grounding and neutral bonding arrangement must be in accordance with local and
national codes of practice.
NOTE
Care must be taken when routing power cable. Ensure that cables do not touch other busbars
(see Figure 11).
NOTE
Do not double-stack lugs: do not layer two lugs on the same side of the busbar (see Figure 11).
4. Connect the AC input supply cables between the power distribution panel and the bypass input
supply busbars (A-B-C or A-B-C-N terminals) and tighten the connections to the proper torque.
Ensure correct phase rotation!
5. If system is one- or two-input, connect the AC input supply cables between the maintenance
bypass cabinet and the UPS bypass input supply busbars (A-B-C or A-B-C-N terminals) and
tighten the connections to the proper torque.
Ensure correct phase rotation!
6. If system is single-input, connect AC jumper connectors between UPS bypass input supply
busbars and UPS rectifier input supply busbars (A-B-C terminals) and tighten the connections to
the proper torque.
Ensure correct phase rotation!
7. Connect the system output power cables between the Maintenance Bypass Cabinet output (A-B-C
or A-B-C-N terminals) and the critical load and tighten the connections to the proper torque.
Ensure correct phase rotation!
8. Connect the auxiliary cables of any external interface/signals to the respective connections of the
output auxiliary terminal block (X4) (see2.0 - Installation Drawings).
9. Replace interior panels and close door.
6
Installation Drawings
INSTALLATION DRAWINGS
Figure 2
Two-Breaker Maintenance Bypass Cabinet, one-input, attached
Two Breaker Maintenance Bypass Cabinet
FBO
MBB
Critical
Load
MIB
2.0
I
Load Bank
(FBO)
BFB
DC Bus
CB1
Main Input
Switchgear
CB2
N
MBJ
UPS Module
Battery
System
EG
MBD
MIB - Maintenance Isolation Breaker
MBB - Maintenance Bypass Breaker
FBO – Furnished By Others
N – Neutral
EG – Equipment Ground
MBJ – Main Bonding Jumper(3-wire systems only)
I
7
- Option Interlock
Installation Drawings
Figure 3
Two-Breaker Maintenance Bypass Cabinet, two-input, attached
MBB
Two Breaker Maintenance Bypass Cabinet
Critical
Load
FBO
MIB
I
Load Bank
(FBO)
BFB
FBO
DC Bus
CB1
CB2
N
Main Input
Switchgear
MBJ
UPS Module
Battery
System
EG
MIB - Maintenance Isolation Breaker
BIB - Bypass Input Breaker
MBB - Maintenance Bypass Breaker
FBO – Furnished By Others
N – Neutral
EG – Equipment Ground
MBJ – Main Bonding Jumper(3-wire systems only)
MBD
I
Figure 4
- Option Interlock
Two-Breaker Maintenance Bypass Cabinet, three-input, attached or detached
Two Breaker Maintenance Bypass Cabinet
MBB
Critical
Load
MIB
FBO
I
Load Bank
(FBO)
BFB
FBO
FBO
Main Input
Switchgear
DC Bus
CB1
CB2
N
MBJ
UPS Module
Battery
System
EG
MIB - Maintenance Isolation Breaker
BIB - Bypass Input Breaker
MBB - Maintenance Bypass Breaker
FBO – Furnished By Others
N – Neutral
EG – Equipment Ground
MBJ – Main Bonding Jumper(3-wire systems only)
MBD
I
8
- Option Interlock
Installation Drawings
Figure 5
Liebert NXL Maintenance Bypass Cabinet—250 and 300kVA main component location
INPUT
OUTPUT
PHASE C
PHASE C
OUTPUT
INPUT
PHASE A
PHASE A
BREAKER REMOVED
FOR CLARITY
GROUND
INPUT
PHASE B
NEUTRAL
OUTPUT
PHASE B
BUSBAR DETAIL B
A
OPTIONAL
SOLENOID
INTERLOCK
B
MAINTENANCE
BYPASS
BREAKER
(MBB)
MAINTENANCE
ISOLATION
BREAKER
(MIB)
CONTROL WIRING
TERMINAL BLOCK
(TB1)
A
SECTION A-A
FRONT
9
Installation Drawings
Figure 6
Liebert NXL Maintenance Bypass Cabinet—400kVA main component location
INPUT
PHASE C
INPUT
PHASE A
GROUND
OUTPUT
PHASE C
OUTPUT
PHASE A
INPUT
PHASE B
NEUTRAL
OUTPUT
PHASE B
BREAKER REMOVED FOR CLARITY
BUSBAR DE TAIL B
A
NEUTRAL BUSBAR
LOCATED IN REAR CORNER
FOR ADDITIONAL LANDING SPACE
OPTIONAL
SOLENOID
INTERLOCK
B
MAINTENANCE
BYPASS
BREAKER
(MBB)
MAINTENANCE
ISOLATION
BREAKER
(MIB)
CONTROL WIRING
TERMINAL BLOCK
(TB1)
A
SECTION A-A
FRONT
10
Installation Drawings
Figure 7
Liebert NXL Maintenance Bypass Cabinet—250 and 300kVA outline drawing
31.3
( 795)
CONDUIT
LANDING
AREA
24.0
( 610)
24.8
( 630)
4.9
( 124)
TYP
56.8
( 1442)
3.9
( 100)
TYP
21.1
( 535)
KNOCK-OUT FOR
CONTROL WIRING
O 1"
3 PLCS
BOTTOM VIEW (FOOTPRINT)
TOP VIEW (DOOR OPEN)
76.8
( 1951)
CG
CG
38.5
( 979)
24.2
(615)
12.2
(309)
38.5
( 979)
22.7
( 578)
33.5
( 850)
NOTES:
1. All dimensions are in inches (mm).
2. 24" minimum clearance above unit required for air exhaust.
3. Keep cabinet within 15 degrees of vertical while handling.
4. Top and bottom cable entry available through removable
KNOCK-OUT FOR
CONTROL WIRING
access plates. Remove, punch to suit conduit size and replace.
O 1"
5. Unit bottom is structurally adequate for forklift handling.
2 PLCS
6. Includes side panel. Side panels are removed between
adjacent units which are bolted togethe r.
7. Control wiring and power wiring must be run in separate conduits.
8. Aluminum and copper-clad aluminum cables are not recommended.
9. All wiring is to be in accordance with national and local electrical codes.
10. Widths are without side panels. The width is 25.6" (650mm) with side panels.
11. The depth dimension includes the front door and rear panel.
11
CONDUIT
LANDING
AREA
21.9
( 555)
16.1
( 410)
BOTTOM CONDUIT PLATES
Installation Drawings
Figure 8
Liebert NXL Maintenance Bypass Cabinet—400kVA outline drawing
37.3
(947)
24.0
( 610)
4.9
(124)
TYP
Conduit
Landing
Area
30.8
(782)
62.8
(1595)
3.9
( 100)
TYP
21.1
(535)
Knock-out for control
wiring O 1.0" (25.4mm)
3 Places
BOTTOM VIEW (FOOTPRINT)
TOP VIEW (DOOR OPEN)
76.8
(1950)
CG
CG
38.5
(979)
12.2
(309)
FRONT
24.2
(615)
See Note 10
38.5
( 979)
39.4
(1000)
See Note 11
28.2
( 716)
SIDE VIEW
NOTES:
1. All dimensions are in inches (mm).
2. 24" minimum clearance above unit required for air exhaust.
3. Keep cabinet within 15 degrees of vertical while handling.
4. Top and bottom cable entry available through removable
access plates. Remove, punch to suit conduit size and replace.
Knock-out for control
5. Unit bottom is structurally adequate for forklift handling.
wiring O 1.0" (25.4mm)
6. Includes side panel. Side panels are removed between
2 Places
adjacent units which are bolted togethe r.
7. Control wiring and power wiring must be run in separate conduits.
8. Aluminum and copper-clad aluminum cables are not recommended.
9. All wiring is to be in accordance with national and local electrical codes.
10. Widths are without side panels. The width is 25.6" (650mm) with side panels.
BOTTOM
11. The depth dimension includes the front door and rear panel.
12
21.9
(556)
Conduit
Landing
Area
16.1
(410)
CONDUIT PLATES
Installation Drawings
Figure 9
Liebert NXL Maintenance Bypass Cabinet—250 and 300kVA terminal details
2.6
( 65 )
2.6
( 65 )
1.6
( 40 )
NOTE:
ALL DIMENSIONS ARE IN inches (mm).
2.0
( 51 )
1.8
( 45 )
4.8
( 123 )
TYP
2.0
( 51 )
BUS BAR DETAIL A
TOP VIEW
BREAKER REMOVED FOR CLARIT
Y
.6
O (14
)
8 PLACES
TYP
1.8
(45)
CUSTOMER
CONNECTION
1.8
( 44 )
BUS TERMINATION DETAIL
A
FRONT VIEW
SIDE VIEW
13
Installation Drawings
Figure 10 Liebert NXL Maintenance Bypass Cabinet—400Kva terminal details
2.57
( 65 )
2.57
( 65)
1.59
( 40 )
4.59
(117)
TYP
O .56
(14)
8 PLACES
TYP
1.75
( 44 )
1.75
( 44 )
2.00
( 51 )
1.78
( 45 )
TOP VIEW
4.84
(123 )
2.00
( 51)
BUS TERMINATION DETAIL
CUSTOMER
CONNECTION
AREA
BUSBAR DETAIL A
BREAKERS REMOVED FOR CLARITY
1.75 ( 44 )
TYP (BOTTOM
ENTRY)
1.75
( 44 )
TYP
(TOP
ENTRY)
3.1
( 79 )
1.37 X .56 SLOT
TYPICAL
(20 PLACES)
O .56
(14)
TYPICAL
(24 PLACES)
A
AUX NEUTRAL BUS DETAIL
NOTE:
ALL DIMENSIONSARE IN inches (mm).
FRONT VIEW
SIDE VIEW
14
Installation Drawings
Figure 11
Cable routing
TOP ENTRY NOTES:
1. Cables from lower busbars must be routed and
tied to the aligning holes on the the cable landing
bar directly above (see figure below). Installation
method is to prevent cables from lower busbars
from contacting the upper busbars.
2. Cables from upper busbars can be optionally tied
also, as shown in top entry view.
3. The UPS output phase cables must be run
on the left side of cabinet, outside of the ground bus.
BOTTOM ENTRY NOTES:
1. Cables from upper busbars must be routed so that
they run clear of lower busbars.
Neutral
Input
Output
Phase B
Ground
Input
Phase C
Output
Phase A
Input
Phase A
Output
Phase C
UPS
Output
Phases
1-3
B
C
1-3C
B
DO NOT DOUBLE-STACK LUGS (PUT
TWO LUGS ON SAME SIDE OF BUSBAR).
THIS IS TO PREVENT THE CABLES
FROM COMING INTO CONTACT WITH
OTHER BUSBARS.
Maintenance
Isolation Breaker
(MIB) Busbar
TOP CABLE ENTRY ROUTING
BOTTOM CABLE ENTRY ROUTING
BREAKERS REMOVED FOR CLARITY
15
Installation Drawings
Figure 12 Liebert NXL Maintenance Bypass Cabinet, one-input system, point-to-point wiring to UPS
S
MBB
MIB
P
Q
R
N
H C
O
F A
L D T
G B
M U E
V
RE
AR
FRONT
V
(+)
L
(-)
BYPASS
NEUTRAL
H K
G J
C
B
F I
K
A
C
J
B
I
P
A
O
C
B
A
OUTPUT
NEUTRAL
UPS
16
N
M
Installation Drawings
Table 1
Run
Liebert-supplied interconnect wiring for one-input Liebert NXL Maintenance Bypass
Cabinet
To
From
Conductor
A
Utility AC - Phase A
MBC Bypass AC - Phase A
Maintenance Bypass AC - Phase A
B
Utility AC - Phase B
MBC Bypass AC - Phase B
Maintenance Bypass AC - Phase B
C
Utility AC - Phase C
MBC Bypass AC - Phase C
Maintenance Bypass AC - Phase C
D
Utility Neutral
MBC Neutral
System Input Neutral
E
Utility Ground
MBC Ground
System Ground
F
MBC Bypass AC - Phase A
UPS Bypass AC - Phase A
UPS Bypass Input - Phase A
G
MBC Bypass AC - Phase B
UPS Bypass AC - Phase B
UPS Bypass Input - Phase B
H
MBC Bypass AC - Phase C
UPS Bypass AC - Phase C
UPS Bypass Input - Phase C
I
UPS Bypass AC - Phase A
UPS Rectifier AC - Phase A
UPS Rectifier Input - Phase A
J
UPS Bypass AC - Phase B
UPS Rectifier AC - Phase B
UPS Rectifier Input - Phase B
K
UPS Bypass AC - Phase C
UPS Rectifier AC - Phase C
UPS Rectifier Input - Phase C
L
MBC Neutral
UPS Bypass Neutral
UPS Neutral
M*
MBC Ground
UPS Equipment Ground
UPS Ground
N
UPS Output AC - Phase A
MBC Output AC - Phase A
UPS Output - Phase A
O
UPS Output AC - Phase B
MBC Output AC - Phase B
UPS Output - Phase B
P
UPS Output AC - Phase C
MBC Output AC - Phase C
UPS Output - Phase C
Q
MBC Output AC - Phase A
Load AC - Phase A
Load AC Input - Phase A
R
MBC Output AC - Phase B
Load AC - Phase B
Load AC Input - Phase B
S
MBC Output AC - Phase C
Load AC - Phase C
Load AC Input - Phase C
T
MBC Neutral
Load Neutral
Load Neutral
U
MBC Ground
Load Ground
Load Equipment Ground
V
MBC Terminal Strip
UPS External Interface Board
Control Wiring
* For detached units only
17
Installation Drawings
Figure 13 Liebert NXL Maintenance Bypass Cabinet, two-input system, point-to-point wiring to UPS
S
MBB
MIB
P
Q
N
R
O
H C
F A
L D T
G B
M U E
V
RE
AR
FRONT
V
BYPASS
NEUTRAL
(+)
L
(-)
H
G
C
B
F
A
C
B
I
A
B
OUTPUT
NEUTRAL
UPS
18
P
O
C
A
K
J
N
M
Installation Drawings
Table 2
Run
Liebert-supplied interconnect wiring for two-input Liebert NXL Maintenance Bypass
Cabinet
To
From
Conductor
A
Utility AC - Phase A
MBC Bypass AC - Phase A
Maintenance Bypass AC - Phase A
B
Utility AC - Phase B
MBC Bypass AC - Phase B
Maintenance Bypass AC - Phase B
C
Utility AC - Phase C
MBC Bypass AC - Phase C
Maintenance Bypass AC - Phase C
D
Utility Neutral
MBC Neutral
System Input Neutral
E
Utility Ground
MBC Ground
System Ground
F
MBC Bypass AC - Phase A
UPS Bypass AC - Phase A
UPS Bypass Input - Phase A
G
MBC Bypass AC - Phase B
UPS Bypass AC - Phase B
UPS Bypass Input - Phase B
H
MBC Bypass AC - Phase C
UPS Bypass AC - Phase C
UPS Bypass Input - Phase C
I
Utility Bypass AC - Phase A
UPS Rectifier AC - Phase A
UPS Rectifier Input - Phase A
J
Utility Bypass AC - Phase B
UPS Rectifier AC - Phase B
UPS Rectifier Input - Phase B
K
Utility Bypass AC - Phase C
UPS Rectifier AC - Phase C
UPS Rectifier Input - Phase C
L
MBC Neutral
UPS Bypass Neutral
UPS Neutral
M*
MBC Ground
UPS Equipment Ground
UPS Ground
N
UPS Output AC - Phase A
MBC Output AC - Phase A
UPS Output - Phase A
O
UPS Output AC - Phase B
MBC Output AC - Phase B
UPS Output - Phase B
P
UPS Output AC - Phase C
MBC Output AC - Phase C
UPS Output - Phase C
Q
MBC Output AC - Phase A
Load AC - Phase A
Load AC Input - Phase A
R
MBC Output AC - Phase B
Load AC - Phase B
Load AC Input - Phase B
S
MBC Output AC - Phase C
Load AC - Phase C
Load AC Input - Phase C
T
MBC Neutral
Load Neutral
Load Neutral
U
MBC Ground
Load Ground
Load Equipment Ground
V
MBC Terminal Strip
UPS External Interface Board
Control Wiring
* For detached units only
19
Installation Drawings
Figure 14 Liebert NXL Maintenance Bypass Cabinet, three-input system, point-to-point wiring to UPS
S
MBB
MIB
P
Q
N
R
C
O
A
P1 D T
B
M U E
V
RE
AR
FRONT
V
BYPASS
NEUTRAL
(+)
(-)
L
H
G
C
B
F
B
I
A
J
C
A
P
O
C
B
A
K
N
M
OUTPUT
NEUTRAL
P1
UPS
20
Installation Drawings
Table 3
Run
Liebert-supplied interconnect wiring for three-input Liebert NXL Maintenance Bypass
Cabinet
To
From
Conductor
A
Utility AC - Phase A
MBC Bypass AC - Phase A
Maintenance Bypass AC - Phase A
B
Utility AC - Phase B
MBC Bypass AC - Phase B
Maintenance Bypass AC - Phase B
C
Utility AC - Phase C
MBC Bypass AC - Phase C
Maintenance Bypass AC - Phase C
D
Utility Neutral
MBC Neutral
System Input Neutral
E
Utility Ground
MBC Ground
System Ground
F
Utility AC - Phase A
UPS Bypass AC - Phase A
UPS Bypass Input - Phase A
G
Utility AC - Phase B
UPS Bypass AC - Phase B
UPS Bypass Input - Phase B
H
Utility AC - Phase C
UPS Bypass AC - Phase C
UPS Bypass Input - Phase C
I
Utility AC - Phase A
UPS Rectifier AC - Phase A
UPS Rectifier Input - Phase A
J
Utility AC - Phase B
UPS Rectifier AC - Phase B
UPS Rectifier Input - Phase B
K
Utility AC - Phase C
UPS Rectifier AC - Phase C
UPS Rectifier Input - Phase C
L
Utility Neutral
UPS Neutral
UPS Neutral
M*
MBC Ground
UPS Equipment Ground
UPS Ground
N
UPS Output AC - Phase A
MBC Output AC - Phase A
UPS Output - Phase A
O
UPS Output AC - Phase B
MBC Output AC - Phase B
UPS Output - Phase B
P
UPS Output AC - Phase C
MBC Output AC - Phase C
UPS Output - Phase C
P1
UPS Output Neutral
MBC Neutral
UPS Neutral
Q
MBC Output AC - Phase A
Load AC - Phase A
Load AC Input - Phase A
R
MBC Output AC - Phase B
Load AC - Phase B
Load AC Input - Phase B
S
MBC Output AC - Phase C
Load AC - Phase C
Load AC Input - Phase C
T
MBC Neutral
Load Neutral
Load Neutral
U
MBC Ground
Load Ground
Load Equipment Ground
V
MBC Terminal Strip
UPS External Interface Board
Control Wiring
* For detached units only
21
Installation Drawings
Figure 15 Liebert NXL Maintenance Bypass Cabinet Control wire diagram without interlock
Connections at UPS External
Interface Board (EIB)
1 3
02-806708
TB0821
TB0811
1
TB0813
3
1
3
1
3
TB0824
LOW VOLTAGE
TERMINAL STRIP
- TB1 21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Table 4
TB1-13
TB1-12
TB1-11
TB1-10
TB1-9
TB1-8
TB1-7
TB1-6
TB1-5
TB1-4
TB1-3
TB1-2
TB0813
TB0811
TB0823
TB0821
EPO PB SW
TB1-1
WIRE DIAGRAM WITHOUT INTERLOCK
22
Control wiring connections without
interlock
From
To
TB1-1
Customer EPO
Push Button Switch
TB1-2
Customer EPO
Push Button Switch
TB1-3
TB0821-2
TB1-4
TB0821-1
TB1-5
TB0824-3
TB1-6
TB0824-2
TB1-7
TB0824-1
TB1-8
TB0811-3
TB1-9
TB0811-2
TB1-10
TB0811-1
TB1-11
TB0813-3
TB1-12
TB0813-2
TB1-13
TB0813-1
Purpose
EPO Signal
Maint. Bypass Enable
Contacts
UPS REPO Contacts
MIB Contacts
MBB Contacts
Installation Drawings
Figure 16 Liebert NXL Maintenance Bypass Cabinet control wire diagram with interlock
Connections at UPS External
Interface Board (EIB)
1 3
TB0821
TB0811
02-806708
1
1
3
1
3
TB0813
3
TB0824 TB0820
1
LOW VOLTAGE
TERMINAL STRIP
- TB1 21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
TB1-16
TB1-15
TB1-14
TB1-13
TB1-12
TB1-11
TB1-10
TB1-9
TB1-8
TB1-7
TB1-6
TB1-5
TB1-4
TB1-3
TB1-2
Table 5
TB0820
TB0813
TB0811
TB0824
TB0821
EPO PB SW
TB1-1
WIRE DIAGRAM WITH INTERLOCK
Control wiring connections with interlock
From
To
TB1-1
Customer EPO
Push Button Switch
TB1-2
Customer EPO
Push Button Switch
TB1-3
TB0821-2
TB1-4
TB0821-1
TB1-5
TB0824-3
TB1-6
TB0824-2
TB1-7
TB0824-1
TB1-8
TB0811-3
TB1-9
TB0811-2
TB1-10
TB0811-1
TB1-11
TB0813-3
TB1-12
TB0813-2
TB1-13
TB0813-1
TB1-14
TB0820-2
TB1-15
TB0820-1
TB1-16
TB0820-3
23
3
Purpose
EPO Signal
Maintenance Bypass
Enable Contacts
UPS REPO Contacts
MIB Contacts
MBB Contacts
EPO Status Contacts
Installation Drawings
Figure 17 Liebert NXL Maintenance Bypass Cabinet control wire routing
CONDUIT KNOCK-OUTS
FOR CONTROL WIRING
A
INTERNAL ROUTING
FOR CONTROL WIRING
INTERNAL ROUNTING
FOR CONTROL WIRING
CONDUIT KNOCK-OUTS
FOR CONTROL WIRING
SECTION A-A
24
A
FRONT VIEW
Installation Drawings
Figure 18 Ground strap location for connected cabinets
Reference of corner post
of connected cabinets
FRONT SIDE OF
UNITS
A
DETAIL A
Cabinet-to-Cabinet
Bolting Instructions
Typical Ground Strap Installation
(Use for all connected units except Battery Cabinet)
25
Specifications
3.0
SPECIFICATIONS
Table 6
Liebert NXL Maintenance Bypass Cabinet specifications
Model Size
250
300
400
Input Parameters
Input Voltage to Bypass, VAC
480V 3-phase, 3-wire or 4-wire
Permissible Input Voltage Range, VAC
+10% to -30%
Input Frequency, Hz
60
Permissible Input Frequency Range, Hz
55 to 65
Neutral Current
1.7 times full phase current
Output Parameters
Inverter Type
IGBT-based Sine-Sine PWM Controlled
Output Power, kW
225
270
Output Voltage, VAC
480V 3-ph, 4-w
Output Frequency, Hz
60
360
Physical Parameters & Standards, in (mm)
Width in. (mm)
without side panels attached
Depth in. (mm)
24.2 (615)
33.5 (850)
33.5 (850)
Height in. (mm)
76.8 (1950)
Weight, lb (kg)
755 (342.5)
Color
Charcoal (ZP-0420)
Front Door Opening (for serviceability)
Degree of Protection for UPS Enclosure
39.4 (1000)
More than 180°
IP 20 (with and without front door open)
UL 1778
CSA 22.2 107.3
FCC Part 15, Class A
ISTA Procedure 1H
WEEE
Standards and Conformities
Minimum clearance, Top, in (mm)
24 (610)
Minimum clearance, Back, in (mm)
0
Minimum clearance, Sides, in (mm)
0
Location of cable entrance
Top or Bottom
Environmental Parameters
Storage Temperature Range, °F (°C)
-13 to 158 (-25 to 70)
Operating Temperature Range, °F (°C)
0 to 40 (UPS)
Maximum 95% Non-Condensing
(Operating and Non-Operating)
Relative Humidity
Maximum Altitude above MSL, ft (m)
4920 (1500) (as per IEC 62040/3) 1% maximum kW derate / 328 rise between 4921-9843
(100 rise between 1500-3000)
26
Specifications
Table 7
Liebert NXL Maintenance Bypass Cabinet current ratings—System Input
UPS Rating
Voltage (VAC)
System Input
kVA
kW
Input
Bypass
Output
Nominal
Current
10 Minute
Overload
External Breaker
Trip, Amps
250
225
480
480
480
301
376
400
300
270
480
480
480
361
451
500
400
360
480
480
480
481
601
700
Table 8
Liebert NXL Maintenance Bypass Cabinet current ratings—System Output
UPS Rating
Voltage, VAC
System Output
kVA
kW
Input
Bypass
Output
Nominal
Current
10 Minute
Overload
External Breaker
Trip, Amps
250
225
480
480
480
301
376
400
300
270
480
480
480
361
451
500
400
360
480
480
480
481
601
700
Table 9
Recommended conduit and cable sizes—Maintenance Bypass Input
Maintenance Bypass Input
UPS Rating
System Input Voltage (VAC)
Nominal Selection
Top Cable Entry
Bottom Cable Entry
Maint
Wire & Conduit
Wire & Conduit
Rectifier Bypass Byp Output Ph, N, G THW / FMC Ph, N, G THW / RNC
Alternate Selection
Top Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / RNC
kVA
kW
250
225
480
480
480
480
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(3) 2C 3-#2/0AWG,
(3) 2.5C 3-#2/0AWG,
2-#2/0AWG, #1/0AWG 2-#2/0AWG, #1/0AWG
300
270
480
480
480
480
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(3) 3C 3-#4/0AWG,
(3) 3C 3-#4/0AWG,
2-#4/0AWG, #1/0AWG 2-#4/0AWG, #1/0AWG
400
360
480
480
480
480
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
500
450
480
480
480
480
(3) 3.5C 3-500kcmil,
(3) 4C 3-500kcmil,
(4) 3C 3-250kcmil,
(4) 3C 3-250kcmil,
2-250kcmil , #1/0AWG 2-250kcmil , #1/0AWG 2-#4/0AWG, #1/0AWG 2-#4/0AWG, #1/0AWG
Table 10
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
Recommended conduit and cable sizes—Rectifier Input (1-Input System)
Rectifier Input (1-Input System)
UPS Rating
System Input Voltage (VAC)
Rectifier Bypass
Nominal Selection
Top Cable Entry
Maint
Wire & Conduit
Byp Output Ph, N, G, THW / FMC
Alternate Selection
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / RNC
Top Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / RNC
(2) 2.5C 3-250kcmil,
#1/0AWG
(2) 2.5C 3-250kcmil,
#1/0AWG
(3) 2C 3-#2/0AWG,
#1/0AWG
(3) 2C 3-#2/0AWG,
#1/0AWG
480
(2) 3C 3-350kcmil,
#1/0AWG
(2) 3C 3-350kcmil,
#1/0AWG
(3) 2.5C 3-#4/0AWG,
#1/0AWG
(3) 2.5C 3-#4/0AWG,
#1/0AWG
480
480
(2) 3C 3-500kcmil,
#1/0AWG
(2) 3.5C 3-500kcmil,
#1/0AWG
(3) 2.5C 3-250kcmil,
#1/0AWG
(3) 2.5C 3-250kcmil,
#1/0AWG
480
480
(3) 3C 3-500kcmil,
#2/0AWG
(3) 3.5C 3-500kcmil,
#2/0AWG
(4) 2.5C 3-250kcmil,
#2/0AWG
(4) 3C 3-250kcmil,
#2/0AWG
kVA
kW
250
225
480
480
480
480
300
270
480
480
480
400
360
480
480
500
450
480
480
27
Specifications
Table 11
Recommended conduit and cable sizes—Module Bypass Input
Module Bypass Input
UPS
Rating
System Input Voltage (VAC)
Maint
kVA kW Rectifier Bypass Byp Output
Nominal Selection
Alternate Selection
Top Cable Entry
Wire & Conduit
Ph, N, G,THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G, THW / RNC
Top Cable Entry
Wire & Conduit
Ph, N, G, THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / RNC
250 225
480
480
480
480
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(3) 2C 3-#2/0AWG,
2-#2/0AWG, #1/0AWG
(3) 2.5C 3-#2/0AWG,
2-#2/0AWG, #1/0AWG
300 270
480
480
480
480
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(3) 3C 3-#4/0AWG,
2-#4/0AWG, #1/0AWG
(3) 3C 3-#4/0AWG,
2-#4/0AWG, #1/0AWG
400 360
480
480
480
480
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
500 450
480
480
480
480
(3) 3.5C 3-500kcmil,
2-250kcmil , #1/0AWG
(3) 4C 3-500kcmil,
2-250kcmil , #1/0AWG
(4) 3C 3-250kcmil,
2-#4/0AWG, #1/0AWG
(3) 3C 3-250kcmil,
2-#4/0AWG, #1/0AWG
Table 12
Recommended conduit and cable sizes—Module Output
UPS
Rating
Module Output
System
Input Voltage (VAC)
kVA kW Rectifier Bypass
Nominal Selection
Maint
Byp Output
Alternate Selection
Top Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / RNC
Top Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / RNC
250 225
480
480
480
480
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(3) 2C 3-#2/0AWG,
2-#2/0AWG, #1/0AWG
(3) 2.5C 3-#2/0AWG,
2-#2/0AWG, #1/0AWG
300 270
480
480
480
480
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(3) 3C 3-#4/0AWG,
2-#4/0AWG, #1/0AWG
(3) 3C 3-#4/0AWG,
2-#4/0AWG, #1/0AWG
400 360
480
480
480
480
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
500 450
480
480
480
480
(3) 3.5C 3-500kcmil,
2-250kcmil , #1/0AWG
(3) 4C 3-500kcmil,
2-250kcmil , #1/0AWG
(4) 3C 3-250kcmil,
2-#4/0AWG, #1/0AWG
(4) 3C 3-250kcmil,
2-#4/0AWG, #1/0AWG
Table 13
Recommended conduit and cable sizes—Load Output
Load Output
UPS Rating
System Input Voltage (VAC)
Alternate Selection
Top Cable Entry
Maint
Wire & Conduit
Byp Output Ph, N, G THW / FMC
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
Top Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
480
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(2) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
(3) 2C 3-#2/0AWG,
(3) 2.5C 3-#2/0AWG,
2-#2/0AWG, #1/0AWG 2-#2/0AWG, #1/0AWG
480
480
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(2) 3.5C 3-350kcmil,
2-350kcmil, #1/0AWG
(3) 3C 3-#4/0AWG,
(3) 3C 3-#4/0AWG,
2-#4/0AWG, #1/0AWG 2-#4/0AWG, #1/0AWG
480
480
480
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(2) 4C 3-500kcmil,
2-500kcmil, #1/0AWG
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
480
480
480
(3) 3.5C 3-500kcmil,
2-250kcmil , #1/0AWG
(3) 4C 3-500kcmil,
(4) 3C 3-250kcmil,
(4) 3C 3-250kcmil,
2-250kcmil , #1/0AWG 2-#4/0AWG, #1/0AWG 2-#4/0AWG, #1/0AWG
kVA
kW
250
225
480
480
480
300
270
480
480
400
360
480
500
450
480
Table 14
Nominal Selection
Rectifier Bypass
Bottom Cable Entry
Wire & Conduit
Ph, N, G THW / FMC
(3) 3C 3-250kcmil,
2-250kcmil, #1/0AWG
Recommended conduit and cable sizes—Load Bank Output
UPS Rating
System Input Voltage, VAC
Load Bank Output
Nominal Selection
Front Cable Entry
Wire-3W + GND
kVA
kW
Rectifier
Bypass
Maint Byp
Output
250
225
480
480
480
480
(1) 3-500kcmil, #1/0AWG
300
270
480
480
480
480
(2) 3-#4/0AWG, #1/0AWG
400
360
480
480
480
480
(2) 3-350kcmil, #1/0AWG
500
450
480
480
480
480
(2) 3-500kcmil, #1/0AWG
28
Specifications
Notes
See the Liebert NXL UPS installation manual, SL-25420, for UPS rectifier, UPS bypass and UPS output sizes. The manual is available at the Liebert Web site: www.liebert.com
These are guidelines only and are superseded by local regulations and codes of practice where applicable.
• Take special care when determining the size of the neutral cable, as current circulating on the
neutral cable may be greater than nominal current in the case of non-linear loads. Refer to the
values given in the Tables 7 and 8.
• The ground conductor should be sized according to the fault rating, cable lengths, type of protection, etc. The ground cable connecting the UPS to the main ground system must follow the most
direct route possible.
• Consideration should be given to the use of smaller, paralleled cables for heavy currents, as a way
to ease installation.
• In most installations, the load equipment is connected to a distribution network of individually
protected busbars fed by the maintenance bypass cabinet output rather than being connected
directly to the Maintenance bypass cabinet itself. Where this is the case, the maintenance bypass
cabinet output cables can be rated to suit the individual distribution network demands rather
than being fully load-rated.
• When laying the power cables, do not form coils to avoid increasing formation of electromagnetic
interference.
Table 15
Recommended lug sizes
Cable Size
T&B Series 54000
Two Hole
#8 AWG
54850BE
#6 AWG
256-30695-868
#4 AWG
256-30695-733
#2-3 AWG
54811BE
#1 AWG
54857BE
#1/0 AWG
256-30695-593
#2/0 AWG
54862BE
#3/0 AWG
54864BE
#4/0 AWG
54866BE
250kcmil
54868BE
300kcmil
54870BE
350kcmil
54872BE
400kcmil
54874BE
500kcmil
54876BE
600kcmil
54878BE
750kcmil
54880BE
Use the T&B crimping tools recommended for these types of lugs.
29
Specifications
30
Ensuring The High Availability
Of Mission-Critical Data And Applications.
Emerson Network Power, the global leader in enabling business-critical
continuity, ensures network resiliency and adaptability through
a family of technologies—including Liebert power and cooling
technologies—that protect and support business-critical systems.
Liebert solutions employ an adaptive architecture that responds
to changes in criticality, density and capacity. Enterprises benefit
from greater IT system availability, operational flexibility and
reduced capital equipment and operating costs.
Technical Support / Service
Web Site
www.liebert.com
Monitoring
800-222-5877
monitoring@emersonnetworkpower.com
Outside the US: 614-841-6755
Single-Phase UPS
800-222-5877
upstech@emersonnetworkpower.com
Outside the US: 614-841-6755
Three-Phase UPS
800-543-2378
powertech@emersonnetworkpower.com
Environmental Systems
800-543-2778
Outside the United States
614-888-0246
Locations
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
7/F, Dah Sing Financial Centre
108 Gloucester Road, Wanchai
Hong Kong
852 2572220
Fax: 852 28029250
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2008 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
SL-25432_REV01_06-08
Emerson Network Power.
The global leader in enabling Business-Critical Continuity.
AC Power
Embedded Computing
Embedded Power
Connectivity
DC Power
Monitoring
EmersonNetworkPower.com
Outside Plant
Power Switching & Controls
Racks & Integrated Cabinets
Services
Precision Cooling
Surge Protection
Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.
©2008 Emerson Electric Co.
Download PDF

advertising