User`s manual | Epic Fitness 1000MX Treadmill User Manual

Model No. EPTL19605.0
Serial No.
Write the serial number in the space
above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-866-997-6999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
USER'S MANUAL
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
TREADMILL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
12. Keep the power cord and the surge suppressor away from heated surfaces.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Read, understand, and test the emergency
stop procedure before using the treadmill (see
TREADMILL OPERATION on page 10).
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
7. The treadmill should not be used by persons
weighing more than 350 pounds. Never allow
more than one person on the treadmill at a time.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. The pulse sensors are not medical devices.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as an exercise aid in determining heart
rate trends in general.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the circuit breaker.)
9. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 22.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
10. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 10. To purchase a surge suppressor,
see your local EPIC dealer or call the toll-free
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
11. Failure to use a properly functioning surge
3
21. Inspect and properly tighten all parts of the
treadmill every three months.
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. Never drop or insert any object into any opening.
23.
DANGER: Always unplug the power
24. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a decal is missing,
or if it is not legible, call the toll-free telephone number on the front cover of this
manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
4
BEFORE YOU BEGIN
Congratulations for purchasing the EPICTM 1000 MX
treadmill. The 1000 MX treadmill offers an impressive
array of features to help you achieve your fitness goals
in the convenience of your home. From the advanced
console to the cushioned walking platform, the 1000
MX treadmill is designed to make each workout more
effective and enjoyable. And when you’re not exercising, the treadmill can be folded away, taking less than
half the floor space of conventional treadmills.
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number of the treadmill is EPTL19605.0. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.iconservice.com/registration.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Console
Accessory Tray
Key/Clip
Storage Latch
Handrail
Handgrip Pulse Sensor
Walking Belt
Reset/Off
Circuit Breaker
Foot Rail
Power Cord
Adjustable Cushion
Walking Platform
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
1
ASSEMBLY
Assembly requires three persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrench
and your own phillips screwdriver
.
For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags,
check to see if the part has been preattached.
Upright Bolt (86)–16
Latch Bolt (77)–2
IMPORTANT: Do not extend the Frame (16) past the vertical position before the console base is assembled or
you may damage the gas spring.
3/8” Star
Washer (88)–8
1
1. Identify the Right Upright (95), which has holes in the indicated locations.
Set the Right Upright (95) near the Frame (16) as
shown. Insert the Upright Wire Harness (108) into the
lower end of the Right Upright and out of the top.
16
Place an elastic band around the Upright Wire Harness
(108) and the Right Upright (95) to keep the Upright Wire
Harness from falling into the Right Upright. Leave the
elastic band on until step 3 is completed.
95
108
Band
6
Holes
2. Slide the Right Upright (95) fully onto the bracket on the
Base (99). Be careful to avoid pinching your hands or
the Upright Wire Harness (108).
2
90
108
95
Attach the Right Upright (95) with four Upright Bolts (86)
and two 3/8” Star Washers (88) as shown. If necessary,
adjust the position of the Right Upright to align the Upright
Bolts with the holes. Do not tighten the Upright Bolts
yet. Attach the Left Upright (90) in the same way. Note:
There are no wires on the left side.
88
86
86
99
3. Attach the Latch Housing (89) to the Left Upright (90)
with two Latch Bolts (77). Do not overtighten the Latch
Bolts.
3
90
89
77
4. Remove the elastic band securing the Upright Wire
Harness (108). Have two persons hold the console assembly near the Left Upright (90) and the Right Upright
(95). Connect the Upright Wire Harness to the Console
Wire Harness (A). Make sure to connect the connectors properly (see the inset drawing); the connectors
should slide together easily and snap into place. If
the connectors do not slide together easily and snap into
place, turn one connector and try again to connect them.
IF THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED
WHEN THE POWER IS TURNED ON.
Insert the Wire Harnesses (A, 108) into the Right Upright
(95). Next, insert the front ends of the brackets on the
console assembly into the Right Upright and the Left
Upright (90). Then, insert the back ends of the brackets
into the Uprights. Make sure that the Wire Harnesses
are not pinched.
7
4
Console
Assembly
90
Front of Bracket
A
108
95
108
5. While pressing down on the Handrails (87), tighten eight
Upright Bolts (86) and four 3/8” Star Washers (88) into
the Uprights (90, 95) and the Handrail (87) as shown. Be
careful to avoid pinching the Upright Wire Harness
(108).
5
38
80
86
43
Note: The CD Holder (38) and the Cup Holder (43) are
replaceable. If these parts become dislodged from the
Console Base (80), simply press them back in.
88
86
90
88
95
87
6. Place the treadmill in the storage position (see HOW TO
FOLD THE TREADMILL FOR STORAGE on page 22).
Center the Frame (16) between the Uprights (90, 95).
Then, tighten the Upright Bolts (86) in the lower ends of
the Uprights.
86
6
16
95
90
86
86
7. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the
walking belt (see page 25). To protect the floor or carpet, place a mat under the treadmill.
8
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
each use, it may remain activated longer than necessary, draining the battery prematurely.
The chest pulse sensor consists of two components—
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
one end of the sensor unit, as shown in the inset drawing. Press the end of the sensor unit under the buckle
on the chest strap. The tab should be flush with the
front of the sensor unit.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° Fahrenheit (50°
Celsius) or below 14° Fahrenheit (-10° Celsius).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
Chest Strap
Tabs
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Tab
CHEST PULSE SENSOR TROUBLESHOOTING
Sensor Unit
Sensor
Unit
The instructions on the following pages explain
how the chest pulse sensor is used with the console. If the chest pulse sensor does not function
properly, try the steps below.
Buckle
Next, wrap the
chest pulse sensor around your
chest and attach
the other end of
the chest strap to
the sensor unit.
Adjust the length
of the chest strap,
if necessary. The
chest pulse sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• Make sure that you are wearing the chest pulse sensor as described at the left. Note: If the chest pulse
sensor does not function when positioned as described, move it slightly lower or higher on your
chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
• As you walk or run on the treadmill, position yourself near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens solution, wet both electrode areas. Return the sensor unit
to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contractions (pvcs), tachycardia bursts, and arrhythmia.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
dried. If the chest pulse sensor is not dried after
• The CR2032 battery in the chest pulse sensor may
need to be replaced (see page 25).
9
TREADMILL OPERATION
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local EPIC dealer or call 1-866-997-6999 and
order part number 146148, or see your local electronics store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
10
Key
Clip
FEATURES OF THE CONSOLE
HOW TO TURN ON THE POWER
The treadmill console offers an impressive array of
features designed to make your workouts more effective.
Note: If there is a sheet of clear plastic on the console, remove the plastic. To prevent damage to the
walking platform, always wear clean shoes while
using the treadmill. The first time the treadmill is
used, observe the alignment of the walking belt,
and center the walking belt if necessary (see page
25).
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even measure your heart rate using the handgrip pulse sensor or
the chest pulse sensor.
Plug in the power cord (see
page 11). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
reset position.
In addition, the console offers ten preset programs.
Each program automatically controls the speed and incline of the treadmill as it guides you through an effective workout. Two heart rate programs are also offered.
Each program automatically adjusts the speed and incline of the treadmill to keep your heart rate within a target range while you exercise. The console even allows
you to create your own programs and save them in
memory for future use.
Reset
Position
Stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing above), and slide
the clip onto the waistband of your clothes. Next, insert
the key into the console. After a moment, the displays
and various indicators will light. Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward until the key is pulled from the console.
If the key is not pulled from the console, adjust the
position of the clip as needed.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a preset program, see page 15. To create and use a custom
program, see pages 17 and 18 To use a heart rate
program, see page 19.
11
When you set either one goal or two goals, the
console will display the length of time you will exercise, the distance that you will walk or run, the
approximate number of calories you will burn, and
a speed setting. If desired, adjust any of the values. Note: The last two values that you change
will become your workout goals.
HOW TO USE THE MANUAL MODE
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select the manual mode.
4
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
When the key is inserted, the manual
mode will be selected
and a track will appear
in the matrix. If a program has been
selected, remove the key and reinsert it to select
the manual mode.
3
Press the Start button to start the walking belt.
As you exercise, change
the speed of the walking
belt as desired by pressing the Speed increase
and decrease buttons.
Each time a button is
pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. To change
the speed setting quickly, press one of the twelve
Quick Speed buttons. Note: The console can display speed and distance in either miles or kilometers (see THE SPEED DISPLAY on page 13).
For simplicity, all instructions in this section
refer to miles.
Set a workout goal if desired.
If you do not plan to set a workout goal, go to step
4.
To set a time, distance, or calorie goal for your
workout, press the increase and decrease buttons
below the Time, Distance, or Calories display. To
set a speed goal, press the Speed buttons. To set
a goal quickly, hold down the increase and decrease buttons. You can set up to two goals for
each workout.
To stop the walking belt, press either of either of
the Stop buttons. The Time display will begin to
flash. To restart the walking belt, press the Start
button or the Speed increase button.
For example, if you
plan to exercise for 30
minutes, press the increase and decrease
buttons below the Time
display until the display
shows a goal of “30:00.”
5
Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline increase and decrease buttons. Each
time a button is pressed,
the incline will change by
0.5%. To change the incline setting quickly, press
one of the twelve Quick Incline buttons. Note: After
the buttons are pressed, it may take a moment for
the treadmill to reach the selected incline setting.
If you also plan to run
two miles during your
workout, press the increase and decrease
buttons below the
Distance display until
the display shows a goal of “2.000.”
12
6
burned. If a goal was set, the display will show the
number of calories still to be burned during your
workout. Note: When a preset program or a custom program is selected, the display will show the
number of calories still to be burned during the
program.
Follow your progress with the matrix and the
displays.
The matrix—When the
manual mode is selected, the matrix will
show a track that represents 1/4 mile. As you
exercise, the indicators
around the track will light in succession until the
entire track is lit. The track will then darken and
the indicators will again begin to light in succession.
The Pulse display—This
display will show your
heart rate when you use
the handgrip pulse sensor
or the chest pulse sensor.
The Incline display—
This display will show the
incline level of the treadmill.
The Speed display—
This display will show the
speed of the walking belt.
The Time display—If
no goals were set, this
display will show the
elapsed time. If a goal
was set, the display will
show the time remaining in your workout. Note: When a program is selected (except for the first heart rate program), the
display will show the time remaining in the program.
Note: The console can
display speed and distance in either miles or
kilometers. To determine
which unit of measurement is selected, hold
down either of the Stop buttons while inserting the
key into the console. An “E” for English miles or an
“M” for metric kilometers will appear in the Calories
display. Press the Speed increase button to
change the unit of measurement. When the desired unit of measurement is selected, remove the
key and then reinsert it.
The Distance
display—If no goals
were set, this display
will show the distance
that you have walked
or run. If a goal was
set, the display will show the distance still to be
walked or run during your workout. Note: When a
preset program or a custom program is selected,
the display will show the distance still to be walked
or run during the program.
To reset the displays, press either of the Stop buttons, remove the key, and then reinsert the key.
If a workout goal was set, the walking belt will automatically slow to a stop when the goal is
reached. If two workout goals were set, the walking belt will stop when both goals are reached.
The Calories display—
If no goals were set, this
display will show the approximate number of
calories you have
13
7
pear in the Pulse display, and then your heart rate
will be shown. For the most accurate heart rate
reading, continue to hold the contacts for
about 15 seconds.
Measure your heart rate if desired.
You can measure your heart rate using either the
handgrip pulse sensor or the chest pulse sensor.
Note: If you hold the handgrip pulse sensor and
wear the chest pulse sensor at the same time, the
console will not display your heart rate accurately.
8
If there are
Contacts
sheets of clear
plastic on the
metal contacts
on the handgrip
pulse sensor,
peel off the
plastic. To use
the handgrip
pulse sensor,
first make sure
that your hands are clean. Next, stand on the
foot rails and hold the handgrip pulse sensor;
your palms should be resting on the upper contacts, and your fingertips should be touching the
lower contacts. Avoid moving your hands. When
your pulse is detected, two dashes (– –) will ap-
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press either of the Stop buttons, and adjust the incline of the treadmill to the
lowest setting. The incline must be at the lowest
setting when the treadmill is folded to the storage position or the treadmill will become damaged. Next, remove the key from the console and
put it in a secure place. Note: If the displays and
various indicators on the console remain lit after
the key is removed, the console is in the
“demo” mode. See page 21 and turn off the
demo mode.
When you are finished using the treadmill, move
the reset/off circuit breaker to the “off” position and
unplug the power cord.
14
4
HOW TO USE A PRESET PROGRAM
1
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Each program is divided into several time segments of equal length. One speed setting and one
incline setting are programmed for each segment.
Note: The same speed setting and/or incline setting may be programmed for two or more consecutive segments.
Select a preset program.
To select a preset program, press the
Programs button repeatedly until one of the
walking, jogging, or running indicators below
the matrix lights.
The speed setting for
Current Segment
the first segment is
shown in the flashing
Current Segment column of the matrix. (The
incline settings are not
shown in the matrix.)
The speed settings for
the next seventeen segments are shown in the
columns to the right.
When a preset program is selected, the Incline
display will show the maximum incline setting of
the program and the Speed display will show the
maximum speed setting. The Time display will
show how long the program will last. The Distance
display will show how far you will walk or run. The
Calories display will show the approximate number of calories you will burn during your workout.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the Speed
display and/or the Incline display will flash to alert
you. When the first segment ends, all speed settings will move one column to the left. The speed
setting for the second segment will then be shown
in the flashing Current Segment column and the
treadmill will automatically adjust to the speed and
incline settings for the second segment. Note: If all
of the indicators in the Current Segment column
are lit after the speed settings have moved to the
left, the speed settings will move downward so
that only the highest indicators appear in the matrix. If some of the indicators in the Current
Segment column are not lit when the speed settings move to the left again, the speed settings will
move back up.
The matrix will show the
first eighteen speed settings of the program.
Note: The ten profiles
below the matrix show
how the speed and incline of the treadmill will change during the programs.
3
Press the Start button to start the program.
Adjust the program settings if desired.
If you do not plan to change any program settings,
go to step 4.
To change the time, distance, or calorie settings
for the program, press the increase and decrease
buttons below the Time, Distance, or Calories display. To change the maximum speed setting,
press the Speed increase and decrease buttons.
To change a setting quickly, hold down the increase and decrease buttons. Note: If you
change one or more program settings, other
settings will change accordingly. For example,
if you change the maximum speed setting, the
distance, and calorie settings will change
accordingly.
15
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
5
Follow your progress with the displays.
See step 6 on page 13.
6
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment column have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: When the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
Measure your heart rate if desired.
See step 7 on page 14.
7
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the incline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a secure place. Note: If the displays and various
indicators on the console remain lit after the
key is removed, the console is in the “demo”
mode. See page 21 and turn off the demo
mode.
To stop the program temporarily, press either of
the Stop buttons. The Time display will begin to
flash. To restart the program, press the Start button or the Speed increase button. After a moment,
the walking belt will begin to move at 1 mph.
When the next segment of the program begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
When you are finished using the treadmill, move
the reset/off circuit breaker to the off position and
unplug the power cord.
16
is shown in the flashing
Current Segment
Current Segment column of the matrix. (The
incline settings are not
shown in the matrix.) To
program a speed setting
and an incline setting for
the first segment, simply
adjust the speed and incline of the treadmill as desired by pressing the Speed and Incline increase
and decrease buttons. Every few times a Speed
button is pressed, an additional indicator will light
or darken in the Current Segment column.
HOW TO CREATE A CUSTOM PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the custom programs.
To select a custom program, press the
Program button repeatedly until one of the two
Custom Program indicators lights.
When the first segment of the program ends, a series of tones will sound and the current speed setting and the current incline setting will be saved in
memory. The three columns of indicators will then
move one column to the left, and the speed setting for the second segment will be shown in the
flashing Current Segment column. Program a
speed setting and an incline setting for the second
segment as described above.
Note: If the custom
program has not yet
been defined, only
three columns of indicators will appear in
the matrix. If more
than three columns of indicators appear, see
HOW TO USE A CUSTOM PROGRAM on page
18.
3
Continue programming speed and incline settings
for as many segments as desired; custom programs can have up to forty segments. When you
are finished with your workout, press either of the
Stop buttons twice. The speed and incline settings
that you have programmed and the number of segments that you have programmed will then be
saved in memory.
Press the Start button and program the desired
speed and incline settings.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
4
See the matrix. Each custom program is divided
into one-minute segments. One speed setting and
one incline setting can be programmed for each
segment. The speed setting for the first segment
When you are finished exercising, remove the
key from the console.
See step 7 on page 16.
17
tings for the next several segments are shown in
the columns to the right.
HOW TO USE A CUSTOM PROGRAM
1
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash, a series of tones will sound, and the Speed display
and the Incline display will flash. When the first
segment ends, all speed settings will move one
column to the left. The speed setting for the second segment will then be shown in the flashing
Current Segment column and the treadmill will automatically adjust to the second speed and incline
settings that you programmed.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the custom programs.
To select a custom program, press the
Program button repeatedly until one of the two
Custom Program indicators lights.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
When a custom program is selected, the Incline
display will show the maximum incline setting of
the program and the Speed display will show the
maximum speed setting. The Time display will
show how long the program will last.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline increase and decrease buttons. When the
current segment ends, the new setting will be saved
in memory. To increase the length of the program, first wait until the program is completed.
Then, press the Start button and program speed
and incline settings for as many additional segments
as desired. When you have added as many segments as desired, press either of the Stop buttons
twice. To decrease the length of the program,
press either of the Stop buttons twice at any time before the program is completed.
The matrix will show
the first eighteen speed
settings of the program.
Note: If only three
columns of indicators
appear in the matrix,
see HOW TO CREATE A CUSTOM PROGRAM
on page 17.
3
Adjust the program settings if desired.
See step 3 on page 15.
4
To stop the program temporarily, press either of
the Stop buttons. The Time display will begin to
flash. To restart the program, press the Start button
or the Speed increase button. After a moment, the
walking belt will begin to move at 1 mph. When
the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
Press the Start button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each custom program
Current Segment
is divided into several
one-minute segments.
One speed setting and
one incline setting are
programmed for each
segment. (The same
speed setting and/or incline setting may be programmed for two or more
consecutive segments.) The speed setting for the
first segment is shown in the flashing Current
Segment column of the matrix. (The incline settings are not shown in the matrix.) The speed set-
5
Follow your progress with the displays.
See step 6 on page 13.
6
Measure your heart rate if desired.
See step 7 on page 14.
7
When you are finished exercising, remove the
key from the console.
See step 7 on page 16.
18
4
HOW TO USE A HEART RATE PROGRAM
If the first heart rate
program is selected, the
target heart rate setting
for the entire program will
flash in the display. If desired, press the Pulse increase and decrease buttons to change the target
heart rate setting (see EXERCISE INTENSITY on
page 26).
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
If the second heart rate program is selected,
the maximum target heart rate setting of the program will flash in the display. If desired, press the
Pulse increase and decrease buttons to change
the maximum target heart rate setting (see EXERCISE INTENSITY on page 26). Note: If the maximum target heart rate setting is changed, the intensity level of the entire program will change.
Follow the steps below to use a heart rate program.
1
Put on the chest pulse sensor.
See the instructions on page 9.
2
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
3
Enter a target heart rate setting.
5
Select a heart rate program.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
To select a heart rate
program, press the
Programs button repeatedly until one of
the two heart rate program indicators lights.
The first heart rate program is divided into 40 oneminute segments. The same target heart rate setting is programmed for all segments. (For a
shorter workout, simply stop the program before it
ends.) The second heart rate program is divided
into 30 one-minute segments. One target heart
rate setting is programmed for each segment.
Note: The same target heart rate setting may be
programmed for two or more consecutive segments.
If the first heart rate
program is selected,
a pulse symbol will
scroll across the matrix.
If the second heart
rate program is selected, the first eighteen target heart rate
settings of the program
will appear in the matrix.
If the second heart rate
Current Segment
program is selected, the
target heart rate setting
for the first segment will
be shown in the flashing
Current Segment column of the matrix. The
target heart rate settings
for the next several segments will be shown in the
columns to the right. When only three seconds remain in the first segment of the program, both the
Current Segment column and the column to the
right will flash and a series of tones will sound.
19
When the first segment ends, all target heart rate
settings will move one column to the left. The target heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
If your pulse is not detected during the program,
the letter “P” will flash in the Pulse display and the
speed of the treadmill may automatically
decrease. If this occurs, see the instructions on
page 9.
During both heart rate programs, the console will
regularly compare your heart rate to the target
heart rate setting for the current segment. If your
heart rate is too far below or above the target
heart rate setting, the speed of the walking belt
will automatically increase or decrease to bring
your heart rate closer to the target heart rate setting.
To stop the program at any time, press either of
either of the Stop buttons. To restart the program,
press the Start button or the Speed increase button. The walking belt will begin to move at 1 mph.
When the console compares your heart rate to the
target heart rate setting, the speed and/or incline
of the treadmill may automatically change to bring
your heart rate closer to the target heart rate setting.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline increase or decrease buttons. However, when the console compares your heart rate to the target heart rate setting, the speed of the treadmill may automatically
change to bring your heart rate closer to the target
heart rate setting.
6
Follow your progress with the displays.
See step 6 on page 13.
7
When you are finished exercising, remove the
key from the console.
See step 7 on page 16.
20
THE INFORMATION MODE/DEMO MODE
HOW TO ADJUST THE CUSHIONING SYSTEM
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been used and the total number of miles that the walking belt has moved. The information mode also allows
you to select miles or kilometers as the unit of measurement for speed and distance. In addition, the information mode allows you to turn on and turn off the
demo mode.
The treadmill features a cushioning system that reduces the impact as you walk or run on the treadmill.
To increase the firmness of the walking platform, slide
the cushion handles (only the right side is shown) toward the rear of the treadmill. To decrease the firmness, slide the cushion handles toward the front of the
treadmill. Note: Make sure both handles are set at
the same cushion level. The faster you run on the
treadmill, or the more you weigh, the firmer the
walking platform should be.
To select the information mode, hold down either of either of the Stop buttons while inserting the key into the
console. When the information mode is selected, the
following information will be shown:
Decrease
The Time display will show
the total number of hours the
treadmill has been used.
Increase
The Distance display will
show the total number of
miles or kilometers that the
walking belt has moved.
Cushion Handle
An “E” for English miles or
an “M” for metric kilometers
will appear in the Calories
display. Press the Speed increase button to change the
unit of measurement if desired.
IMPORTANT: The Pulse
display should be blank. If
a “d” appears in the display,
the console is in the “demo”
mode. This mode is intended
to be used only when a
treadmill is displayed in a store. When the console is in
the demo mode, the power cord can be plugged in, the
key can be removed from the console, and the displays
and indicators on the console will automatically light in
a preset sequence, although the buttons on the console
will not operate. If a “d” appears in the Pulse display
when the information mode is selected, press the
Speed decrease button so the display is blank.
To exit the information mode, remove the key from the
console.
21
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the end of the treadmill near the location indicated by
the arrow at the right. To decrease the possibility of injury, bend your legs and keep your back straight. As
you raise the frame, make sure to lift with your legs
rather than your back. Raise the frame about halfway to
the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
aligned with the latch pin. Then, slowly release the latch
knob. Make sure that the latch pin is fully inserted into
the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit..
Latch
Knob
Pin
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
latch pin is fully inserted into the catch.
1. Hold the treadmill and place one foot against one of the
wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
22
Wheels
Base
Closed
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Pivot the frame down until it is past the
latch pin. Then, slowly release the latch knob.
Pin
Latch
Knob
Catch
2. Hold the treadmill firmly with both hands, and lower the
frame to the floor. To decrease the possibility of injury,
bend your legs and keep your back straight.
23
Open
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppressor that meets all of the specifications described on page 10. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the frame near the
power cord. If the switch protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five minutes and then
press the switch back in.
c
Off
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see 1. c. above). If the circuit breaker has tripped, wait for five
minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the hood
and carefully remove the hood. Locate the Reed Switch
(42) and the Magnet (24) on the left side of the Pulley (40).
Turn the Pulley until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8”. If necessary, use a
slotted screwdriver to move the Reed Switch slightly.
Reattach the Hood, making sure that the Screws are inserted into the same holes from which they were removed.
Run the treadmill for a few minutes to check for a correct
speed reading.
24
a
1/8”
40
42
Top
View
24
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be
permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the included allen
wrench, turn both rear roller bolts counterclockwise
1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the
walking belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is
properly tightened.
b
3–4”
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the
walking belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
a
b
PROBLEM: The chest pulse sensor does not function properly
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROUBLESHOOTING on page 9.
b. If the chest pulse sensor still does not function properly, the battery
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Next, remove the old battery from the sensor unit. Insert a new CR
2032 battery, making sure that the writing is on top. In addition, make
sure that the rubber gasket is in place in the sensor unit. Replace the
battery cover and turn it to the closed position.
25
b
Battery
Cover
Battery
Rubber
Gasket
EXERCISE GUIDELINES
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
26
PART LIST—Model No. EPTL19605.0
R1205A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key
No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
2
32
1
2
4
2
2
2
2
15
1
2
1
1
1
1
2
1
1
2
23
2
1
1
9
2
2
4
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
Foot Rail Cover
3/4” Screw
Left Foot Rail
Handle Decal
Handle Screw
Cushion Handle
Cushion Housing
Isolator
Ball Detent
1/2” Screw
Latch Warning Decal
Platform Screw, Rear
Latch Catch
Walking Belt
Walking Platform
Frame
Belt Guide
Left Rear Endcap
Rear Roller
Wheel Endcap
Screw
Isolator Guide
Front Roller
Magnet
Nut
Frame Pivot Bushing
Frame Pivot Spacer
Frame Pivot Washer
Frame Pivot Bolt
Idler Pulley Nut
Idler Pulley Washer
Idler Pulley
Idler Pulley Bolt
Idler Arm Bolt
Idler Arm Bushing
Idler Arm
Idler Arm Spring
CD Holder
Front Left Endcap
Motor Belt
Drive Motor
Reed Switch
Cup Holder
Reed Switch Clip
Key
No. Qty.
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
4
1
1
2
2
1
1
2
1
15
1
1
1
1
1
1
1
1
5
1
1
2
1
6
4
70
71
72
73
74
75
1
1
1
2
2
2
76
77
78
79
80
81
82
83
84
85
86
1
2
2
1
1
1
2
11
1
1
16
Description
Hood Bracket
Ground Wire
Lift Frame
Motor Bolt
Motor Bushing
Filter Wire
Controller Plate
Small Star Washer
Lift Motor Bolt, Top
Electronic Screw
Front Right Endcap
Controller
Power Cord
Access Door
Transformer
Key Clip
Ground Wire, Console
Hood Cover
Hood Screw
Hood Plate
Hood
Lift Pivot Washer
Motor Belly Pan
Belly Pan Fastener
Frame Belly
Pan Screw
Allen Wrench
Frame Belly Pan
Right Rear Endcap
Rear Foot
Rear Roller Bolt
Rear Roller
Star Washer
Pulse Wire
Latch Bolt
Platform Nut
5/32” Allen Wrench
Console Base
Console
Platform Bolt, Front
Console Back Screw
Latch Pin Assembly
Console Back
Upright Bolt
27
Key
No. Qty.
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
1
8
4
1
2
2
2
1
1
1
4
4
1
2
2
1
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
#
#
#
1
1
1
2
11
1
2
4
4
4
1
2
2
2
2
1
1
1
1
1
2
2
1
1
1
Description
Handrail
3/8” Star Washer
Belt Guide Screw
Left Upright
Lift Pivot Bolt
Wheel Bolt
Front Wheel
Shock
Right Upright
Right Foot Rail
Base Pad
Base Pad Screw
Base
Base Endcap
Caution Decal
Lift Motor
Bolt, Bottom
Incline Motor
Stop Bracket
Releasable Tie
Tie Holder
Plastic Tie
Upright Wire Harness
Handrail Endcap
Pulse Sensor Screw
Pulse Sensor
Pulse Sensor Base
Left Foam Grip
Wire Tie
Wire Tie Screw
Shock Clip
Foot Rail Cover Base
Right Foam Grip
Console Matrix
Chest Pulse Sensor
Chest Pulse Strap
Chest Pulse Receiver
Platform Bolt, Front
Platform Nut
8” Blue Wire, 2 F
4” Blue Wire, 2 F
User’s Manual
#These parts are not illustrated
EXPLODED DRAWING—Model No. EPTL19605.0
R1205A
41
40
2
69
35
34
10
50
37
36
57
54
39
31
25
33
42
48
45
21
51
49
44
48
30
1
32
69
31
27 26
29
6
10
24
21
8
21
78
21
45
21
82
7
69
4
10
28
28
22
52
54
25 53
21
3
117
5
56
54
47
45
2
25
59
46
69
23
25
17
9
2
21
45
55
89
26
16
21
27
82
63
28
62
28
69
11
63
29
13
63
15
78
1
12
14
65
17
117
64
69
18
63
69
68
96
89
21
9
12
21
74
68
75
69
21
19
21
21
63
8
7
6
5
73
2
72
71
22
21
74
4
68
75
21
21
73
67
68
70
79
21
69
69
EXPLODED DRAWING—Model No. EPTL19605.0
R1205A
10
80
61
81
83
86
83
83
83
88
119
83
86
86
88
108
77
84
83
90
86
38
86
43
86
95
83
58
2
88
86
2
83
92
120
85
91
115
2
121
108
25
20
122
2
86
93
66
25
88
86
94
116
2
114
60
97
101
112
110
66
110
20
76
103
97
112
110
98
100
118
92
97
25
98
102
101
105
99
21
106
109
93
110
111
113
25 25
104
111
87
109
91
98
107
100
97
98
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information:
• the MODEL NUMBER of the product (EPTL19605.0)
• the NAME of the product (EPIC 1000 MX treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for ten (10) years after
the date of purchase. Parts and labor are warranted for two (2) years after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 231012 R1205A
Printed in USA © 2005 ICON IP, Inc.
Download PDF

advertising