User`s manual | Epic Fitness EPTL09605.0 Treadmill User Manual

Model No. EPTL09605.0
Serial No.
Write the serial number in the space
above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-866-997-6999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
USER'S MANUAL
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
TREADMILL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Keep the power cord and the surge suppressor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 22 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
TREADMILL OPERATION).
7. The treadmill should not be used by persons
weighing more than 300 pounds. Never allow
more than one person on the treadmill at a time.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
9. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the circuit breaker.)
10. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 9. To purchase a surge suppressor,
see your local EPIC dealer or call the toll-free
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
3
tenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and properly tighten all parts of the
treadmill every three months.
22. Never drop or insert any object into any opening.
23.
24. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a decal is missing,
or if it is not legible, call the toll-free telephone number on the front cover of this
manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
4
BEFORE YOU BEGIN
Congratulations for purchasing the EPICTM 450 MX
treadmill. The 450 MX treadmill offers an impressive
array of features designed to make your workouts at
home more effective and enjoyable. And when you’re
not exercising, the treadmill can be folded away, taking
less than half the floor space of conventional treadmills.
number and serial number before contacting us. The
model number of the treadmill is EPTL09605.0. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.iconservice.com/registration.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Accessory Tray
Console
Handrail
Key/Clip
Storage Latch
Handgrip Pulse Sensor
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Cushion Walking Platform
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrench
and adjustable wrench
.
and your own Phillips screwdriver
For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags,
check to see if the part has been preattached.
Console Bolt (86)–4
Wheel Bolt (92)–2
1” Tek Screw (98)–4
Nut (25)–2
1. With the help of a second person, carefully raise the
Uprights (99) to the position shown. Have the second person hold the console assembly near the Uprights as
shown. Look under the console assembly and locate the
Console Wire Harness (22).
Cut the plastic ties securing the Upright Wire Harness
(82) to the right Upright (99). Connect the Upright Wire
Harness to the Console Wire Harness (22). Make sure to
connect the connectors properly (see the inset drawing). The connectors should slide together easily and
snap into place. If the connectors do not slide together
easily and snap into place, turn one connector and try
again. IF THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED
WHEN THE POWER IS TURNED ON.
6
Star Washer (88)–4
1
Console
Assembly
22
82
22
99
108
2. Insert the Wire Harnesses (22, 82) into the right Upright
(99).
2
Console
Assembly
Set the console assembly on the Uprights (99). While a
second person holds the console assembly, attach it with
four Console Bolts (86) and four Console Washers (88)
as shown. Start all four Console Bolts and then firmly
tighten them.
22, 82
88
88
86
86
99
3. Insert a Wheel (93) into a Wheel Housing (43). Attach the
Wheel with a Wheel Bolt (92) and a Nut (25). Note: Do
not overtighten the Nut; the Wheel should turn freely.
3
99
Tip the Uprights (99) forward slightly and insert the Wheel
Housing (43) into the base of the Uprights as shown.
Attach the other Wheel (not shown) and Wheel Housing
(not shown) as described above.
25
43
93
4. With the help of a second person, carefully lower the
Uprights (99). Make sure that the Wheel Housings (43)
remain in the base of the Uprights.
92
4
99
97
98
Attach each Wheel Housing (43) with a 1” Tek Screw
(98). Next, attach the two Base Pads (97) to the base of
the Uprights (99) with 1” Tek Screws (98).
With the help of a second person, carefully raise the
Uprights (99) to the vertical position.
98
43
7
5. Remove the backing from the indicated tape on the console assembly. Press the Book Holder (62) firmly onto
the tape. Note: The Book Holder may be preassembled.
5
62
Console
Assembly
Tape
6. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the
treadmill to protect the floor or carpet. For your benefit, we recommend that you familiarize yourself with
the TROUBLESHOOTING section on pages 22 and 23.
If you purchase the optional chest pulse sensor (see
page 19), follow the steps below to install the receiver
included with the chest pulse sensor.
1. Make sure that the power cord is unplugged. Remove
the indicated Screw (2) and the Access Door (95).
2. Remove the paper from the adhesive pad on the back of
the receiver (A). Orient the receiver so the small cylinder is near the lower edge of the receiver and is facing the Console Back (85) as shown. Firmly press the
receiver onto the indicated corner of the Access Door
(95). Connect the wire on the receiver to the Pulse Wire
(49) extending from the Console Back.
3. Make sure that no wires are pinched. Reattach the
Access Door (95) with the Screw (2). Note: The other
wires included with the receiver may be discarded.
8
85
49
A
Cylinder
95
2
TREADMILL OPERATION
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local EPIC dealer or call the toll-free telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
9
Key
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable.
Clip
Note: If there is a sheet of clear plastic on the face of
the console, peel off the plastic. To prevent damage to
the walking platform, wear clean athletic shoes while
using the treadmill. The first time the treadmill is used,
observe the alignment of the walking belt, and center
the walking belt if necessary (see page 23).
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sensor or the optional chest pulse sensor (see page 19).
HOW TO TURN ON THE POWER
In addition, the console offers six preset programs. Each
program automatically controls the speed and incline of
the treadmill as it guides you through an effective workout. You can even create custom workout programs
and store them in memory for future use.
Two heart rate programs are also offered. Each program automatically adjusts the speed and incline of the
treadmill to keep your heart rate near target heart rate
settings while you exercise. Note: You must wear the
optional chest pulse sensor to use the heart rate programs.
1
Plug in the power cord (see page 9).
2
Locate the reset/off circuit breaker on the
treadmill frame near
the power cord. Make
sure that the circuit
breaker is in the “reset”
position.
3
To use the manual mode of the console, follow the
steps beginning on page 11. To use a preset program,
see page 13. To create and use a custom program,
see pages 15 and 16. To use a heart rate program,
see page 17.
10
Reset
Position
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing above) and
slide the clip onto the waistband of your clothes.
Next, insert the key into the console. After a moment, the displays will light. Important: In an
emergency situation, the key can be pulled
from the console, causing the walking belt to
slow to a stop. Test the clip by carefully taking
a few steps backward; if the key is not pulled
from the console, adjust the position of the
clip.
5
HOW TO USE THE MANUAL MODE
1
The left display—This display will show the
elapsed time, your pace (in minutes per mile), and
the incline level of the treadmill. Note: When a program is selected, this display will show the time
remaining in the program instead of the elapsed
time. Each time the incline of the treadmill
changes, the display will show the incline setting
for several seconds.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
10.
2
Select the manual mode.
When the key is inserted, the manual mode will be
selected. If you have selected a program, press
the Manual button to reselect the manual mode.
3
Follow your progress with the two displays.
Training Zone Bar
Track
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the ten numbered Speed buttons.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed increase and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. Note: After
the buttons are pressed, it may take a moment for
the walking belt to reach the selected speed setting.
The left display will also show a training zone bar
that indicates the approximate intensity of your exercise. For example, if four to six segments of the
bar appear, the bar shows that your exercise intensity is ideal for weight loss.
When the manual mode is selected, the left display
will also show a track. As you exercise, the indicators around the track will appear in succession
until the entire track is lit. The track will then disappear the indicators will again begin to appear in
succession.
If one of the numbered Speed buttons is pressed,
the walking belt will gradually increase in speed
until it reaches the selected speed setting.
The right display—This display will show the distance that you have walked or run, the number of
1/4-mile laps you have completed, the speed of
the walking belt, and the approximate numbers of
calories and fat calories you have burned (see
FAT BURNING on page 24).
To stop the walking belt, press the Stop button.
The time will begin to flash in the left display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
Speed buttons.
4
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time a
button is pressed, the incline will change by 0.5%.
To change the incline setting quickly, press the
numbered Incline buttons. Note: After the buttons
are pressed, it may take a moment for the treadmill
to reach the selected incline setting.
11
To use the handgrip pulse sensor, stand on the
foot rails and hold the handgrip pulse sensor with
your palms resting on the metal contacts; avoid
moving your hands. When your pulse is detected,
the heart-shaped indicator in the right display will
flash each time your heart beats, one or two
dashes (– –) will appear, and then your heart rate
will be shown. For the most accurate heart rate
reading, continue to hold the contacts for
about 15 seconds.
The right display will also show your heart rate
when you use the handgrip pulse sensor or the
optional chest pulse sensor. In addition, during
heart rate programs the right display will show a
heart rate bar that shows your heart rate as a percentage of your age-predicted maximum heart
rate (see step 3 on page 17 for an explanation of
your age-predicted maximum heart rate). For example, if four to six segments of the bar appear,
your heart rate is between 60% and 70% of your
age-predicted maximum heart rate.
Note: The handgrip pulse sensor is intended to be
used only for heart rate measurement. Do not
use the handgrip pulse sensor as a handlebar.
Always hold the handrails for support when
you are not measuring your heart rate.
Heart Rate Bar
7
To turn on the fan, press the button below the fan.
To turn on the fan at high speed, press the button
a second time. To turn off the fan, press the button a third time. Note: If the fan is on when the
walking belt is stopped, the fan will automatically
turn off after a few minutes.
Note: The console can display speed and distance in either miles or kilometers. The letters
“MPH” or “Km/H” will appear in the right display to
show which unit of measurement is selected. To
change the unit of measurement, see THE INFORMATION MODE/DEMO MODE on page 19.
For simplicity, all instructions in this section
refer to miles.
8
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will become damaged. Next,
remove the key from the console and put it in a secure place. Note: If the displays remain lit after
the key is removed, the console is in the
“demo” mode. See page 19 and turn off the
demo mode.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
6
Turn on the fan if desired.
Measure your heart rate if desired.
Note: If you use
the handgrip
pulse sensor
and the optional
chest pulse sensor at the same
time, the conContacts
sole will not display your heart
rate accurately. Before using the handgrip pulse
sensor, remove the sheets of clear plastic from
the metal contacts. In addition, make sure that
your hands are clean.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
12
The speed setting for the
Current Segment
first segment will be
Column
shown in the flashing
Current Segment column
of the matrix. (The incline settings are not
shown in the matrix.)
The speed settings for
the next seven segments
will be shown in the columns at the right.
HOW TO USE A PRESET PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 10.
2
Select a preset program.
To select a preset program, press the Speed &
Incline Programs button repeatedly. The right display will show which program (P-1 to P-6) is selected.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash, and
a series of tones will sound. If the speed and/or incline of the treadmill is about to change, the left
display and/or the right display will flash to alert
you. When the first segment ends, all speed settings in the matrix will move one column to the
left. The speed setting for the second segment will
then be shown in the flashing Current Segment
column, and the treadmill will automatically adjust
to the speed and incline settings for the second
segment. Note: If all of the indicators in the
Current Segment column are lit after the speed
settings have moved to the left, the speed settings
may move downward so that only the highest indicators appear in the matrix. If some indicators in
the Current Segment column are not lit when the
speed settings move to the left again, the speed
settings will move back up.
When a preset program is selected, the left display will flash the maximum incline setting of the
program for a few seconds, and the right display
will flash the maximum speed setting. The left display will then show how long the program will last.
In addition, the matrix in the left display will show
the first several speed settings of the program.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
Matrix
3
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or disappear in the Current Segment column. (If any of
the columns to the right of the Current Segment
column have the same number of indicators as the
Current Segment column, an additional indicator
may appear or disappear in those columns as
well.) Note: When the next segment of the program begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline setting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive segments.
13
To stop the program at any time, press the Stop
button. The time will begin to flash in the left display. To restart the program, press the Start button
or the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automatically adjust to the speed and incline settings for the
next segment.
4
7
When the program ends, make sure that the incline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a secure place. Note: If the displays and various
indicators remain lit after the key is removed,
the console is in the “demo” mode. See page
19 and turn off the demo mode.
Follow your progress with the displays.
See step 5 on page 11.
5
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
Measure your heart rate if desired.
See step 6 on page 12.
6
When you are finished exercising, remove the
key from the console.
Turn on the fan if desired.
See step 7 on page 12.
14
See the matrix in the left
Current Segment
display. Each custom
Column
program is divided into
one-minute segments.
One speed setting and
one incline setting can
be programmed for each
segment. The speed setting for the first segment
will be shown in the flashing Current Segment column of the matrix. (The incline settings are not
shown in the matrix.) To program a speed setting
and an incline setting for the first segment, simply
adjust the speed and incline of the treadmill as desired by pressing the Speed and Incline buttons.
Every few times a Speed button is pressed, an
additional indicator will appear or disappear in the
Current Segment column.
HOW TO CREATE A CUSTOM PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 10.
2
Select a custom program.
To select a custom program, press the Custom
Programs button repeatedly until “P-9,” “P-10,” “P11,” or “P-12” appears in the right display.
When the first segment of the program ends, the
current speed setting and the current incline setting will be stored in memory. The three columns
of indicators will then move one column to the left,
and the speed setting for the second segment will
be shown in the flashing Current Segment column.
Program a speed setting and an incline setting for
the second segment as described above.
If the custom program has not yet been defined,
three columns of indicators will appear in the matrix in the left display. If more than three
columns of indicators appear, see HOW TO
USE A CUSTOM PROGRAM on page 16.
Continue programming speed and incline settings
for as many segments as desired; custom programs can have up to forty segments. When you
are finished with your workout, press the Stop button twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Matrix
3
Press the Start button or the Speed increase
button and program the desired speed and incline settings.
4
When you are finished exercising, remove the
key from the console.
See step 7 on page 14.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
15
column and the column to the right will flash, a series of tones will sound, the speed setting and the
incline setting will flash in the displays, and all
speed settings will move one column to the left.
The speed setting for the second segment will then
be shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you programmed previously.
HOW TO USE A CUSTOM PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 10.
2
Select a custom program.
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and the last segment ends. The
walking belt will then slow to a stop.
To select a custom program, press the Custom
Programs button repeatedly until “P-9,” “P-10,” “P11,” or “P-12” appears in the right display.
When a custom program is selected, the left display will flash the maximum incline setting of the
program for a few seconds, and the right display
will flash the maximum speed setting. The left display will then show how long the program will last.
In addition, the matrix in the left display will show
the first several speed settings of the program.
Note: If only three columns of indicators appear, see HOW TO CREATE A CUSTOM PROGRAM on page 15.
3
If desired, you can redefine the program while
using it. To change the speed or incline setting
during the current segment, simply press the
Speed or Incline buttons. When the current segment
ends, the new setting will be saved in memory. To
increase the length of the program, first wait until
the program ends. Then, press the Start button, and
program speed and incline settings for as many additional segments as desired. When you have
added as many segments as desired, press the
Stop button twice. To decrease the length of the
program, press the Stop button twice at any time
before the program ends.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
To stop the program at any time, press the Stop
button. The time will begin to flash in the left display. To restart the program, press the Start button or the Speed increase button.
Each program is divided into several one-minute
segments. One speed setting and one incline setting are programmed
for each segment. The
Current Segment
speed setting for the
Column
first segment will be
shown in the flashing
Current Segment column of the matrix. (The
incline settings are not
shown in the matrix.)
The speed settings for
the next several segments will be shown in the
columns to the right.
4
Follow your progress with the displays.
See step 5 on page 11.
5
Measure your heart rate if desired.
See step 6 on page 12.
6
Turn on the fan if desired.
See step 7 on page 12.
7
When only three seconds remain in the first segment of the program, both the Current Segment
When you are finished exercising, remove the
key from the console.
See step 7 on page 14.
16
Note: Your age-predicted maximum heart rate is
calculated by subtracting your age from 220. For
example, if you are 30 years old, your age-predicted maximum heart rate is 190 beats per
minute (220 – 30 = 190).
HOW TO USE A HEART RATE PROGRAM
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether
the medication will affect your exercise heart
rate.
4
If heart rate program 7 is selected, the letters
“PLS” and the target heart rate setting for the program will begin to flash in the right display. If desired, change the target heart rate setting by
pressing the + or – button beside the Enter button
(see EXERCISE INTENSITY on page 24). Then,
press the Enter button.
Follow the steps below to use a heart rate program.
1
Enter a target heart rate setting for the program.
Put on the chest pulse sensor.
Note: You must wear the optional chest pulse
sensor (see page 19) to use a heart rate program. While using the chest pulse sensor, do
not use the handgrip pulse sensor.
2
Insert the key into the console.
If heart rate program 8 is selected, the letters
“PLS” and the maximum target heart rate setting
for the program will begin to flash in the right display. If desired, change the maximum target heart
rate setting by pressing the + or – button beside
the Enter button (see EXERCISE INTENSITY on
page 24). Then, press the Enter button. Note: If
the maximum target heart rate setting is changed,
the intensity level of the entire program will
change.
See HOW TO TURN ON THE POWER on
page 10.
3
Select a heart rate program.
To select a heart rate program, press the Heart
Rate Control Programs button repeatedly until
“P-7” or “P-8” appears in the right display.
5
Enter your age.
The word “AGE” and the current age setting will
then begin to flash in the right display. If you have
already entered your age, press the Enter button.
If you have not entered your age, press the + or –
button beside the Enter button to enter your age,
and then press the Enter button.
If heart rate program 7 is selected, a pulse symbol will scroll across the matrix in the left display.
If heart rate program 8 is selected, the matrix in
the left display will show the first several target
heart rate settings of the program.
Note: During heart rate program 7, your heart rate
will remain near a target heart rate setting that
you select. During heart rate program 8, your
heart rate will reach approximately 85% of your
age-predicted maximum heart rate.
17
6
heart rate is too far below or above the target
heart rate setting, the speed of the walking belt
will automatically increase or decrease to bring
your heart rate closer to the target heart rate setting.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
when the console compares your heart rate to the
target heart rate setting, the speed of the treadmill
may automatically change to bring your heart rate
closer to the target heart rate setting.
Heart rate program 7 is divided into several oneminute segments. The same target heart rate setting is programmed for all segments. (For a
shorter workout, simply stop the program before it
ends.) Heart rate program 8 is divided into 30
one-minute segments. One target heart rate setting is programmed for each segment. Note: The
same target heart rate setting may be programmed for two or more consecutive segments.
If your pulse is not detected during the program,
the letters “PLS” will flash in the right display and
the speed of the treadmill may automatically decrease. If this occurs, see the instructions included
with the optional chest pulse sensor.
If heart rate program
Current Segment
8 is selected, the target
Column
heart rate setting for
the first segment will
be shown in the flashing Current Segment
column of the matrix.
The target heart rate
settings for the next
several segments will be shown in the columns to
the right. When only three seconds remain in the
first segment of the program, both the Current
Segment column and the column to the right will
flash and a series of tones will sound.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the console
compares your heart rate to the target heart rate
setting, the speed and/or incline of the treadmill
may automatically change to bring your heart rate
closer to the target heart rate setting.
7
Follow your progress with the displays.
See step 5 on page 11.
When the first segment ends, all target heart rate
settings will move one column to the left. The target heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
8
Turn on the fan if desired.
See step 7 on page 12.
9
During both heart rate programs, the console
will regularly compare your heart rate to the target
heart rate setting for the current segment. If your
When you are finished exercising, remove the
key from the console.
See step 7 on page 14.
18
THE INFORMATION MODE/DEMO MODE
IMPORTANT: If the letter “d” appears in the right display, the “demo” mode is selected. This mode is intended to be used only when a treadmill is displayed in
a store. When the demo mode is selected, the power
cord can be plugged in, the key can be removed from
the console, and the displays and indicators on the
console will automatically light in a preset sequence,
although the buttons on the console will not operate. If
a “d” appears in the right display when the information mode is selected, press the Speed decrease
button.
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
demo mode.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release the Stop button. When the information mode is
selected, the following information will be shown:
To exit the information mode, remove the key from the
console.
The left display will show
the total number of hours
that the treadmill has been
used.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more features to the console. The chest pulse sensor offers
hands-free operation, and enables you to use the console’s two heart rate programs. To purchase the optional chest pulse sensor, call the toll-free telephone number on the front cover of this manual.
The right display will show the total number of miles (or
kilometers) that the walking belt has moved. In addition,
the right display will show the letter “E” for English miles
or the letter “M” for metric kilometers. Press the Speed
increase button to change the unit of measurement if
desired.
19
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the end of the treadmill near the location indicated by
the arrow at the right. To decrease the possibility of injury, bend your legs and keep your back straight. As
you raise the frame, make sure to lift with your legs
rather than your back. Raise the frame about halfway to
the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
aligned with the pin on the latch knob. Slowly release the
latch knob. Make sure that the pin on the latch knob is
fully inserted into the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
Closed
Pin
Latch
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
pin on the latch knob is fully inserted into the catch.
1. Hold the treadmill and place one foot against one of the
wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot against a wheel, and carefully lower the
treadmill until the base is resting in the storage position.
20
Wheel
Base
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Pivot the frame down until it is past the
pin on the latch knob. Then, slowly release the latch
knob.
Pin
Latch
Knob
Catch
2. Hold the frame firmly with both hands, and lower it to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
21
Open
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. Make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the frame near the
power cord. If the switch protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five minutes and then
press the switch back in.
c
Off
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see 1. c. above). If the circuit breaker has tripped, wait for five
minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the hood
and carefully remove the hood. Locate the Reed Switch
(42) and the Magnet (24) on the left side of the Pulley (23).
Turn the Pulley until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8”. If necessary, use a
slotted screwdriver to move the Reed Switch slightly.
Reattach the Hood, making sure that the Screws are inserted into the same holes from which they were removed.
Run the treadmill for a few minutes to check for a correct
speed reading.
22
a
1/8”
23
42
Top
View
24
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be
permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the included allen
wrench, turn both rear roller bolts counterclockwise
1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the
walking belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is
properly tightened.
b
3–4”
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the
walking belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
23
a
b
EXERCISE GUIDELINES
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
24
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for
each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
25
5
NOTES
26
PART LIST—Model No. EPTL09605.0
R1105A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key
No. Qty. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
2
54
1
1
1
1
1
1
1
4
1
4
1
1
1
1
2
4
4
2
15
1
1
1
9
2
2
4
2
1
1
1
1
1
1
1
1
2
Foot Rail Cover
3/4” Screw
Left Foot Rail
Left Handgrip, Top
Left Handgrip, Bottom
Right Handgrip, Top
Right Handgrip, Bottom
Console Fan
Fan Housing
1/2” Screw
Latch Warning Decal
Platform Screw
Catch
Walking Belt
Walking Platform
Frame
Belt Guide
Isolator Bolt
Isolator
Front Platform Screw
Screw
Console Wire Harness
Front Roller
Magnet
Nut
Frame Pivot Bushing
Frame Pivot Spacer
Frame Pivot Washer
Frame Pivot Bolt
Idler Pulley Nut
Hood
Idler Pulley
Idler Pulley Bolt
Idler Arm Bolt
Idler Arm Bushing
Idler Arm
Idler Arm Spring
Idler Arm Washer
Key
No. Qty. Description
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
2
1
1
1
2
1
4
1
1
2
1
1
1
3
1
13
1
1
1
2
1
2
1
1
5
1
1
4
1
4
1
1
1
1
2
2
2
2
Releasable Tie
Motor Belt
Drive Motor
Reed Switch
Wheel Housing
Reed Switch Clip
Hood Bracket
Ground Wire
Lift Frame
Motor Bolt
Pulse Wire
Filter Wire
Controller Plate
Small Star Washer
Lift Motor Bolt, Top
Electronics Screw
Front Roller Bushing
Controller
Power Cord
Latch Screw
Transformer
Fan Screw
Pulse Bar
Book Holder
Hood Screw
Front Right Endcap
Front Left Endcap
Motor Belly Pan Screw
Motor Belly Pan
Pulse Bar Screw
Console Frame
Allen Wrench
Rear Roller
Right Endcap
Rear Foot
Rear Roller Bolt
Rear Roller Star Washer
Lift Frame Washer
27
Key
No. Qty. Description
77 4
78 1
79 2
80 1
81 1
82 1
83 8
84 1
85 1
86 4
87 2
88 4
89 1
90 1
91 2
92 2
93 2
94 1
95 1
96 1
97 2
98 4
99 1
100 2
101 2
102 1
103 1
104 1
105 1
106 4
107 12
108 2
#
1
#
1
U-nut
Key/Clip
Shock Clip
Console Base
Console
Upright Wire Harness
Plastic Tie
Latch Pin Assembly
Console Back
Console Bolt
Tie Holder
Star Washer
Static Decal
Left Rear Endcap
Lift Pivot Bolt
Wheel Bolt
Front Wheel
Shock
Access Door
Right Foot Rail
Base Pad
1” Tek Screw
Upright
Upright Endcap
Caution Decal
Lift Motor Bolt, Bottom
Incline Motor
Stop Bracket
Hood Plate
Belt Guide Screw
Foot Rail Screw
Latch Washer
8” Blue Wire, 2 F
User’s Manual
#These parts are not illustrated
21
73
75
74
2
2
90
107
74
75
21
2
1
12
2
11
73
72
2
14
13
107
1
96
18
71
107
19
3
15
70
106
12
12 16
17
18
107
65
2
20
12
107
19
29
33
34
28
32
18
19
37
24
20
40
44
106
107
42
26
25
27
30
38
25
55
36
28
38
23
35
2
66
18
19
66
17
64
45
21
21
EXPLODED DRAWING—Model No. EPTL09605.0
28
41
29
67
46
28
63
27
47
25 53
105
26
48
54
25
45
R1105A
51
50
21
66
45
31
21
59
45
54
56
10
10
63
52
54
57
63
63
63
2
2
61
5
58
108
84
9
2
81
4
2
2
80
8
60
2
22
49
2
2
2
62
78
2
2
2
2
6
2
7
2
2
83
39
2
2
87
21
93
92
2
2 89
2
85
95
2
98
43
EXPLODED DRAWING—Model No. EPTL09605.0
2
25
101
68
25
104
103
69
R1105A
88
93
102
77
25
86
98
98
91
76
43
86
88
101
100
97
68
77
92
25
94
79
99
91
82
76
98
97
100
25
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, please be prepared
to provide the following information:
• the MODEL NUMBER of the product (EPTL09605.0)
• the NAME of the product (EPIC 450 MX treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for ten (10) years after
the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 230795 R1105A
Printed in USA © 2005 ICON IP, Inc.
Download PDF

advertising