EPSON Perfection® 2400 Photo
t
r
a
t
S
e
r
He
2
Install the Software
Wait! You must install your software before connecting the
scanner to your computer. The installation process may take
several minutes. Be sure to close all open programs and turn
off any virus protection programs.
If you don’t already have Adobe Photoshop or Photoshop Elements on your
computer, install Photoshop Elements from the CD-ROM included with your
scanner before you install the scanner software.
Note: The software works with Windows® 98, Me, 2000, and XP,
and Macintosh® OS 8.6 to 9.x and OS X 10.2.x. Macintosh OS 10.1.x
is not supported. Follow the steps below for your system.
Windows
1
6
Follow the on-screen instructions to install each program. Click Quit
to continue, as needed. Note that EPSON Smart Panel installs in
several steps.
7
At the end of the installation, click Exit.
8
If you see a Product Registration screen, register your scanner as
instructed. At the last screen, click Done or close your browser.
9
Follow the instructions below to connect the scanner. Then restart your
system to fully activate the scanner and software.
3
1
Remove the yellow sticker from the back of the scanner.
Remove the
yellow sticker
4
At the Software Installation screen, click Install.
Your First Scan
Raise the scanner lid and
place your photo face
down on the glass.
Place top of
photo in the
upper right corner
Then close the lid.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
Read the license agreement, then click Agree.
r
e
n
n
s
a
c
i
s
Sc
a
B
1
• Windows 98, Me, and 2000: Double-click My Computer,
then double-click the EPSON CD-ROM icon.
3
Now you’re ready to start scanning!
After your software is installed, it’s time to get connected!
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The installer starts automatically. If it doesn’t start, do the following:
Plug the flat end
of the
cable into any available USB port
on your computer.
Note: Your system may not work
correctly if you use a USB cable
other than the one supplied by
EPSON or if you connect to your
computer through a hub.
Connect the Scanner
• Windows XP: Click Start, click My Computer,
then double-click the EPSON CD-ROM icon.
2
8
Arrow
2
Connect the cable for the builtin transparency unit to the
connector on the back of the
scanner. (The small arrow on the
cable should be facing up.)
3
Slide the transportation lock all
the way to the right.
2
Press the
Transportation
lock
Start button on the scanner.
Start button
AC adapter
1
1
4
Unpack Your Scanner
Click Install
5
Follow the on-screen instructions to install each program.
Note that EPSON Smart Panel™ installs in several steps.
6
At the end of the installation, click Exit.
7
When you see the Product Registration screen, register your scanner
as instructed. At the last screen, click Done or close your browser.
Connect the AC adapter
and power cord,
as shown.
Power cord
EPSON Smart Panel opens on your computer.
Make sure you have everything:
Built-in
transparency unit
AC adapter
Scanner
Power cord
Connect the AC adapter
to the scanner.
Macintosh
1
CD-ROM with EPSON
scanner software and
electronic manual
5
®
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The EPSON folder opens on your desktop. If it doesn’t open,
double-click the
EPSON CD-ROM icon.
AC adapter
USB cable
2
If you are using Mac® OS X, double-click the Mac OS X folder in the
EPSON folder, then double-click the
EPSON icon.
6
Plug the other end of the power
cord into an electrical outlet.
3
Film holder
If you are using Mac OS 8.6 to 9.x, double-click the
in the EPSON folder.
Adobe® Photoshop® Elements
CD-ROM
3
See your on-screen Scanner Reference Guide for detailed scanning
instructions.
2
Remove all the packing tape, but leave the yellow sticker
in place for now.
IMPORTANT!
Leave the yellow sticker in
place until you’re instructed
to remove it.
Note: In Windows XP, you may see a message the first time you
press any of the scanner buttons. Select EPSON Smart Panel,
click Always use this program for this action, then click OK.
EPSON icon
The scanner turns on and begins
to warm up. The
Start button
on the front of the scanner flashes.
It stops flashing and turns green
when the scanner is ready.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
4
If you see a license agreement, click Agree to continue.
5
At the Software Installation screen, click Install. Enter your Administrator
name and password, if necessary.
Note: If you’re installing on Macintosh OS 8.6 to 9.x, you may
see a prompt to update your Carbon Library. After the CarbonLib
installation is complete and you’ve restarted your system, doubleclick the
EPSON icon, then click Install to continue the
installation.
7
Plug the square end
of the USB cable into the
scanner’s USB port.
Start button
Click the
Scan and Save icon.
A progress meter appears on the screen and your photo is automatically
scanned. After your photo is scanned, the View Image screen opens.
4
Click Next to continue.
5
When you see the following screen,
select a location and file type for
your scanned image, then
click Save.
The image is saved to the location
specified. To view it, double-click
the image or open it in an
application like Photoshop
Elements.
Turn Over
EPSON Perfection® 2400 Photo
t
r
a
t
S
e
r
He
2
Install the Software
Wait! You must install your software before connecting the
scanner to your computer. The installation process may take
several minutes. Be sure to close all open programs and turn
off any virus protection programs.
If you don’t already have Adobe Photoshop or Photoshop Elements on your
computer, install Photoshop Elements from the CD-ROM included with your
scanner before you install the scanner software.
Note: The software works with Windows® 98, Me, 2000, and XP,
and Macintosh® OS 8.6 to 9.x and OS X 10.2.x. Macintosh OS 10.1.x
is not supported. Follow the steps below for your system.
Windows
1
6
Follow the on-screen instructions to install each program. Click Quit
to continue, as needed. Note that EPSON Smart Panel installs in
several steps.
7
At the end of the installation, click Exit.
8
If you see a Product Registration screen, register your scanner as
instructed. At the last screen, click Done or close your browser.
9
Follow the instructions below to connect the scanner. Then restart your
system to fully activate the scanner and software.
3
1
Remove the yellow sticker from the back of the scanner.
Remove the
yellow sticker
4
At the Software Installation screen, click Install.
Your First Scan
Raise the scanner lid and
place your photo face
down on the glass.
Place top of
photo in the
upper right corner
Then close the lid.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
Read the license agreement, then click Agree.
r
e
n
n
s
a
c
i
s
Sc
a
B
1
• Windows 98, Me, and 2000: Double-click My Computer,
then double-click the EPSON CD-ROM icon.
3
Now you’re ready to start scanning!
After your software is installed, it’s time to get connected!
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The installer starts automatically. If it doesn’t start, do the following:
Plug the flat end
of the
cable into any available USB port
on your computer.
Note: Your system may not work
correctly if you use a USB cable
other than the one supplied by
EPSON or if you connect to your
computer through a hub.
Connect the Scanner
• Windows XP: Click Start, click My Computer,
then double-click the EPSON CD-ROM icon.
2
8
Arrow
2
Connect the cable for the builtin transparency unit to the
connector on the back of the
scanner. (The small arrow on the
cable should be facing up.)
3
Slide the transportation lock all
the way to the right.
2
Press the
Transportation
lock
Start button on the scanner.
Start button
AC adapter
1
1
4
Unpack Your Scanner
Click Install
5
Follow the on-screen instructions to install each program.
Note that EPSON Smart Panel™ installs in several steps.
6
At the end of the installation, click Exit.
7
When you see the Product Registration screen, register your scanner
as instructed. At the last screen, click Done or close your browser.
Connect the AC adapter
and power cord,
as shown.
Power cord
EPSON Smart Panel opens on your computer.
Make sure you have everything:
Built-in
transparency unit
AC adapter
Scanner
Power cord
Connect the AC adapter
to the scanner.
Macintosh
1
CD-ROM with EPSON
scanner software and
electronic manual
5
®
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The EPSON folder opens on your desktop. If it doesn’t open,
double-click the
EPSON CD-ROM icon.
AC adapter
USB cable
2
If you are using Mac® OS X, double-click the Mac OS X folder in the
EPSON folder, then double-click the
EPSON icon.
6
Plug the other end of the power
cord into an electrical outlet.
3
Film holder
If you are using Mac OS 8.6 to 9.x, double-click the
in the EPSON folder.
Adobe® Photoshop® Elements
CD-ROM
3
See your on-screen Scanner Reference Guide for detailed scanning
instructions.
2
Remove all the packing tape, but leave the yellow sticker
in place for now.
IMPORTANT!
Leave the yellow sticker in
place until you’re instructed
to remove it.
Note: In Windows XP, you may see a message the first time you
press any of the scanner buttons. Select EPSON Smart Panel,
click Always use this program for this action, then click OK.
EPSON icon
The scanner turns on and begins
to warm up. The
Start button
on the front of the scanner flashes.
It stops flashing and turns green
when the scanner is ready.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
4
If you see a license agreement, click Agree to continue.
5
At the Software Installation screen, click Install. Enter your Administrator
name and password, if necessary.
Note: If you’re installing on Macintosh OS 8.6 to 9.x, you may
see a prompt to update your Carbon Library. After the CarbonLib
installation is complete and you’ve restarted your system, doubleclick the
EPSON icon, then click Install to continue the
installation.
Continue
7
Plug the square end
of the USB cable into the
scanner’s USB port.
Start button
Click the
Scan and Save icon.
A progress meter appears on the screen and your photo is automatically
scanned. After your photo is scanned, the View Image screen opens.
4
Click Next to continue.
5
When you see the following screen,
select a location and file type for
your scanned image, then
click Save.
The image is saved to the location
specified. To view it, double-click
the image or open it in an
application like Photoshop
Elements.
Turn Over
EPSON Perfection® 2400 Photo
t
r
a
t
S
e
r
He
2
Install the Software
Wait! You must install your software before connecting the
scanner to your computer. The installation process may take
several minutes. Be sure to close all open programs and turn
off any virus protection programs.
If you don’t already have Adobe Photoshop or Photoshop Elements on your
computer, install Photoshop Elements from the CD-ROM included with your
scanner before you install the scanner software.
Note: The software works with Windows® 98, Me, 2000, and XP,
and Macintosh® OS 8.6 to 9.x and OS X 10.2.x. Macintosh OS 10.1.x
is not supported. Follow the steps below for your system.
Windows
1
6
Follow the on-screen instructions to install each program. Click Quit
to continue, as needed. Note that EPSON Smart Panel installs in
several steps.
7
At the end of the installation, click Exit.
8
If you see a Product Registration screen, register your scanner as
instructed. At the last screen, click Done or close your browser.
9
Follow the instructions below to connect the scanner. Then restart your
system to fully activate the scanner and software.
3
1
Remove the yellow sticker from the back of the scanner.
Remove the
yellow sticker
4
At the Software Installation screen, click Install.
Your First Scan
Raise the scanner lid and
place your photo face
down on the glass.
Place top of
photo in the
upper right corner
Then close the lid.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
Read the license agreement, then click Agree.
r
e
n
n
s
a
c
i
s
Sc
a
B
1
• Windows 98, Me, and 2000: Double-click My Computer,
then double-click the EPSON CD-ROM icon.
3
Now you’re ready to start scanning!
After your software is installed, it’s time to get connected!
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The installer starts automatically. If it doesn’t start, do the following:
Plug the flat end
of the
cable into any available USB port
on your computer.
Note: Your system may not work
correctly if you use a USB cable
other than the one supplied by
EPSON or if you connect to your
computer through a hub.
Connect the Scanner
• Windows XP: Click Start, click My Computer,
then double-click the EPSON CD-ROM icon.
2
8
Arrow
2
Connect the cable for the builtin transparency unit to the
connector on the back of the
scanner. (The small arrow on the
cable should be facing up.)
3
Slide the transportation lock all
the way to the right.
2
Press the
Transportation
lock
Start button on the scanner.
Start button
AC adapter
1
1
4
Unpack Your Scanner
Click Install
5
Follow the on-screen instructions to install each program.
Note that EPSON Smart Panel™ installs in several steps.
6
At the end of the installation, click Exit.
7
When you see the Product Registration screen, register your scanner
as instructed. At the last screen, click Done or close your browser.
Connect the AC adapter
and power cord,
as shown.
Power cord
EPSON Smart Panel opens on your computer.
Make sure you have everything:
Built-in
transparency unit
AC adapter
Scanner
Power cord
Connect the AC adapter
to the scanner.
Macintosh
1
CD-ROM with EPSON
scanner software and
electronic manual
5
®
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The EPSON folder opens on your desktop. If it doesn’t open,
double-click the
EPSON CD-ROM icon.
AC adapter
USB cable
2
If you are using Mac® OS X, double-click the Mac OS X folder in the
EPSON folder, then double-click the
EPSON icon.
6
Plug the other end of the power
cord into an electrical outlet.
3
Film holder
If you are using Mac OS 8.6 to 9.x, double-click the
in the EPSON folder.
Adobe® Photoshop® Elements
CD-ROM
3
See your on-screen Scanner Reference Guide for detailed scanning
instructions.
2
Remove all the packing tape, but leave the yellow sticker
in place for now.
IMPORTANT!
Leave the yellow sticker in
place until you’re instructed
to remove it.
Note: In Windows XP, you may see a message the first time you
press any of the scanner buttons. Select EPSON Smart Panel,
click Always use this program for this action, then click OK.
EPSON icon
The scanner turns on and begins
to warm up. The
Start button
on the front of the scanner flashes.
It stops flashing and turns green
when the scanner is ready.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
4
If you see a license agreement, click Agree to continue.
5
At the Software Installation screen, click Install. Enter your Administrator
name and password, if necessary.
7
Start button
Click the
Scan and Save icon.
A progress meter appears on the screen and your photo is automatically
scanned. After your photo is scanned, the View Image screen opens.
Plug the square end
of the USB cable into the
scanner’s USB port.
4
Click Next to continue.
5
When you see the following screen,
select a location and file type for
your scanned image, then
click Save.
The image is saved to the location
specified. To view it, double-click
the image or open it in an
application like Photoshop
Elements.
Note: If you’re installing on Macintosh OS 8.6 to 9.x, you may
see a prompt to update your Carbon Library. After the CarbonLib
installation is complete and you’ve restarted your system, doubleclick the
EPSON icon, then click Install to continue the
installation.
Continue
Turn Over
EPSON Perfection® 2400 Photo
t
r
a
t
S
e
r
He
2
Install the Software
Wait! You must install your software before connecting the
scanner to your computer. The installation process may take
several minutes. Be sure to close all open programs and turn
off any virus protection programs.
If you don’t already have Adobe Photoshop or Photoshop Elements on your
computer, install Photoshop Elements from the CD-ROM included with your
scanner before you install the scanner software.
Note: The software works with Windows® 98, Me, 2000, and XP,
and Macintosh® OS 8.6 to 9.x and OS X 10.2.x. Macintosh OS 10.1.x
is not supported. Follow the steps below for your system.
Windows
1
6
Follow the on-screen instructions to install each program. Click Quit
to continue, as needed. Note that EPSON Smart Panel installs in
several steps.
7
At the end of the installation, click Exit.
8
If you see a Product Registration screen, register your scanner as
instructed. At the last screen, click Done or close your browser.
9
Follow the instructions below to connect the scanner. Then restart your
system to fully activate the scanner and software.
3
1
Remove the yellow sticker from the back of the scanner.
Remove the
yellow sticker
4
At the Software Installation screen, click Install.
Your First Scan
Raise the scanner lid and
place your photo face
down on the glass.
Place top of
photo in the
upper right corner
Then close the lid.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
Read the license agreement, then click Agree.
r
e
n
n
s
a
c
i
s
Sc
a
B
1
• Windows 98, Me, and 2000: Double-click My Computer,
then double-click the EPSON CD-ROM icon.
3
Now you’re ready to start scanning!
After your software is installed, it’s time to get connected!
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The installer starts automatically. If it doesn’t start, do the following:
Plug the flat end
of the
cable into any available USB port
on your computer.
Note: Your system may not work
correctly if you use a USB cable
other than the one supplied by
EPSON or if you connect to your
computer through a hub.
Connect the Scanner
• Windows XP: Click Start, click My Computer,
then double-click the EPSON CD-ROM icon.
2
8
Arrow
2
Connect the cable for the builtin transparency unit to the
connector on the back of the
scanner. (The small arrow on the
cable should be facing up.)
3
Slide the transportation lock all
the way to the right.
2
Press the
Transportation
lock
Start button on the scanner.
Start button
AC adapter
1
1
4
Unpack Your Scanner
Click Install
5
Follow the on-screen instructions to install each program.
Note that EPSON Smart Panel™ installs in several steps.
6
At the end of the installation, click Exit.
7
When you see the Product Registration screen, register your scanner
as instructed. At the last screen, click Done or close your browser.
Connect the AC adapter
and power cord,
as shown.
Power cord
EPSON Smart Panel opens on your computer.
Make sure you have everything:
Built-in
transparency unit
AC adapter
Scanner
Power cord
Connect the AC adapter
to the scanner.
Macintosh
1
CD-ROM with EPSON
scanner software and
electronic manual
5
®
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The EPSON folder opens on your desktop. If it doesn’t open,
double-click the
EPSON CD-ROM icon.
AC adapter
USB cable
2
If you are using Mac® OS X, double-click the Mac OS X folder in the
EPSON folder, then double-click the
EPSON icon.
6
Plug the other end of the power
cord into an electrical outlet.
3
Film holder
If you are using Mac OS 8.6 to 9.x, double-click the
in the EPSON folder.
Adobe® Photoshop® Elements
CD-ROM
3
See your on-screen Scanner Reference Guide for detailed scanning
instructions.
2
Remove all the packing tape, but leave the yellow sticker
in place for now.
IMPORTANT!
Leave the yellow sticker in
place until you’re instructed
to remove it.
Note: In Windows XP, you may see a message the first time you
press any of the scanner buttons. Select EPSON Smart Panel,
click Always use this program for this action, then click OK.
EPSON icon
The scanner turns on and begins
to warm up. The
Start button
on the front of the scanner flashes.
It stops flashing and turns green
when the scanner is ready.
When you see the message about disabling your antivirus software,
verify that you have disabled the software, then click Continue.
4
If you see a license agreement, click Agree to continue.
5
At the Software Installation screen, click Install. Enter your Administrator
name and password, if necessary.
Note: If you’re installing on Macintosh OS 8.6 to 9.x, you may
see a prompt to update your Carbon Library. After the CarbonLib
installation is complete and you’ve restarted your system, doubleclick the
EPSON icon, then click Install to continue the
installation.
7
Plug the square end
of the USB cable into the
scanner’s USB port.
Start button
Click the
Scan and Save icon.
A progress meter appears on the screen and your photo is automatically
scanned. After your photo is scanned, the View Image screen opens.
4
Click Next to continue.
5
When you see the following screen,
select a location and file type for
your scanned image, then
click Save.
The image is saved to the location
specified. To view it, double-click
the image or open it in an
application like Photoshop
Elements.
Starting a Scan
Smart Panel
1
To select the Color Restoration setting, open Smart Panel and select
Reprint Photo. You see the screen below.
2
Click the Color Restoration icon.
You can start a scan in several different ways:
• You can use the scanner buttons. Press the button for the type of scan
you want. Smart Panel automatically opens and scans your documents.
Then follow the easy on-screen instructions to finish your task.
4
Place the film holder on the scanner as shown. The film strip side of the
holder should be toward the center, and the 35 mm slide holders should
be aligned with the right edge of the scanner glass.
To Purchase an Optional Film Adapter or Other Accessories
Call the EPSON StoreSM at (800) 873-7766 or visit our web site at
www.epsonstore.com (U.S. sales only). In Canada, please call (800) 873-7766
for dealer referral.
Software Technical Support
If you’re having problems with your software, use the contact information below.
Slide holders
Note: If you are using Windows XP, you will have to select EPSON
Smart Panel and Always use this program for this action the
first time you press each of the buttons.
Software
Telephone
EPSON Scan
U.S.
(562) 276-4382
support.epson.com
Canada
(905) 709-3839
Start
Click here to
scan and print
6:00 AM to 6:00 PM,
PT, Monday-Friday
If you’re scanning slides, reverse the film holder so the 35 mm slide
holders are toward the center and the film strip holder is aligned with the
right edge of the scanner glass. Then place the slides in the holder.
Copy
EPSON Scan
Scan to Web
Internet and E-mail
Film strip holder
Click Color
Restoration
Scan to E-mail
Fax
Color restoration is available in Home and Professional modes.
1
To select Color Restoration,
start EPSON Scan.
You see a screen
similar to this.
EPSON Smart
Panel
(510) 445-8616
Adobe
Photoshop
Elements
Windows
(206) 675-6358
(510) 445-8601
www.newsoftinc.com
tech@newsoftinc.com
www.adobe.com/support
Macintosh
(206) 675-6258
• You can start Smart Panel by clicking the
icon on your desktop,
and use it to perform various types of scans.
Problems?
• You can start EPSON Scan from Adobe Photoshop Elements or any
other TWAIN-compliant program. You can also start the EPSON Scan
program directly from your computer.
Select Color
Restoration
Selecting the Scanning Mode
EPSON Scan has three scanning modes:
Click the Preview button at the bottom of the screen.
• Full Auto Mode for automatic control
of scan settings.
3
Select the Color Restoration checkbox. (If you’re using Professional
Mode, you may need to scroll to the bottom of the screen.)
• Professional Mode for full control
over all scan settings.
Start EPSON Scan and select either Home Mode or Professional Mode.
Note: You can also scan film and slides in Full Auto mode, although
you won’t have control over the settings.
2
• Home Mode for more control over scan
settings, including Color Restoration.
First, check the
5
Scanning Film
The scanner cover has a built-in film transparancy unit. To scan film or negative
strips, slides, or transparencies, you need to remove the document mat from the
scanner cover and insert the film in a holder.
1
To change settings in Full Auto Mode, click the Pause button, then click
Options. If you’re using Home or Professional Mode, the options window
automatically appears. Then select the settings you want to use for your scan.
2
Note: The selected mode and settings remain in effect until they
are changed.
Make sure the cable for the transparency unit is connected to the scanner
(see section 3). If you need to connect the cable, first disconnect the
scanner from the electrical outlet. After you have connected the cable,
plug the scanner back into the outlet.
Flashing green
Warming up or scanning.
Green
Ready to scan.
Flashing red
Make sure the transportation lock is unlocked
(see section 3).
Home Mode: Select the correct Document Type: Color Negative Film,
B&W Negative Film, or Positive Film (for slides and transparencies).
Try restarting your computer and turning the
scanner off and then on again.
Professional Mode: Select Transparency as your Document Type.
Then select the Film Type: Color Negative Film, B&W Negative Film,
or Positive Film.
Tip: Make sure your film is dust-free
for the best scan. You can also select
the Dust Removal setting in EPSON
Scan, as shown.
If the red light is still flashing, contact your dealer
or EPSON.
Off
Click to lessen
the appearance
of dust
If your problem is listed here, try these suggestions.
You see a message about
a HI-SPEED USB device
in Windows XP.
Uninstall the following programs: EPSON Photo
Print, EPSON Scan, EPSON Smart Panel,
and ScanToWeb. In the Windows Control Panel,
use the Add/Remove Programs utility to uninstall
software. Then follow the instructions on the
other side of this sheet to reinstall your scanner
software.
Got Questions?
Here’s where to look for answers:
If you have faded photos or negatives, you can use the Color Restoration
setting in your software to improve the color of your scan. You can select this
setting in Smart Panel or in EPSON Scan.
On-screen Scanner Reference Guide
Double-click the Scanner Reference Guide icon on your desktop.
On-screen Help for Smart Panel and EPSON Scan
Click the Help button or question mark that appears on the screen when you’re
using these programs.
3
Locate the film holder that came with your scanner. Slide a strip of 35 mm
film into the film strip holder, with the film’s shiny side side facing down.
Click the x in the corner of the message to
close it. Your scanner will work correctly,
although not at maximum speed.
You see an error message Make sure the scanner is connected to your
computer and plugged into a power source.
when you try to scan, or
the scanner doesn’t scan.
Make sure the transportation lock is pushed all
the way to the right (see section 3).
Open the scanner cover. Pull the handle for the document mat up slightly
until the handle is free of the cover, then pull the document mat forward
and out.
Restoring Color in Photos
Make sure your scanner is connected to your
computer and plugged into a working power source.
The New Hardware Wizard Click Cancel and follow the steps in “Install the
appears on your screen.
Software” on the other side of this sheet.
Disconnect the scanner before installing
the software.
Follow these steps to scan 35 mm film or slides:
To change the scanning mode, choose the mode you want to use from the
Mode list box at the top right of the window.
light on the scanner.
EPSON Technical Support
EPSON provides technical assistance 24 hours a day through the electronic
support services and automated telephone services described below:
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Automated Telephone Services
To use Automated Telephone Services, you must have a touch tone
telephone and call (800) 922-8911. Your EPSON SoundAdviceSM Express
Code is 70395. Use it to quickly select your scanner in SoundAdvice.
To Speak to a Technical Support Representative
Dial (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM, Pacific
Time, Monday through Friday. Toll or long distance charges may apply.
You can’t scan negatives
or slides.
Make sure the scanner film holder is positioned
correctly, and the scanner glass is clean.
Make sure the cable for the transparency unit is
connected to the scanner (see section 3) and the
reflective document mat is removed.
If you’re using Home or Professional mode,
make sure the Document Type or Film Type
matches what you’re scanning: either Color
Negative Film, B&W Negative Film, or Positive
Film (for slides and transparencies).
EPSON is a registered trademark and EPSON Smart Panel is a trademark of SEIKO EPSON
CORPORATION. EPSON Perfection is a registered trademark, and EPSON Store and SoundAdvice are
service marks of Epson America, Inc.
General Notice: Other product names are for identification purposes only and may be trademarks
of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. Printed on recycled paper. 6/03
Printed in XXX
CPD-14017R2
4025689-02
Starting a Scan
Smart Panel
1
To select the Color Restoration setting, open Smart Panel and select
Reprint Photo. You see the screen below.
2
Click the Color Restoration icon.
You can start a scan in several different ways:
• You can use the scanner buttons. Press the button for the type of scan
you want. Smart Panel automatically opens and scans your documents.
Then follow the easy on-screen instructions to finish your task.
4
Place the film holder on the scanner as shown. The film strip side of the
holder should be toward the center, and the 35 mm slide holders should
be aligned with the right edge of the scanner glass.
To Purchase an Optional Film Adapter or Other Accessories
Call the EPSON StoreSM at (800) 873-7766 or visit our web site at
www.epsonstore.com (U.S. sales only). In Canada, please call (800) 873-7766
for dealer referral.
Software Technical Support
If you’re having problems with your software, use the contact information below.
Slide holders
Note: If you are using Windows XP, you will have to select EPSON
Smart Panel and Always use this program for this action the
first time you press each of the buttons.
Software
Telephone
EPSON Scan
U.S.
(562) 276-4382
support.epson.com
Canada
(905) 709-3839
Start
Click here to
scan and print
6:00 AM to 6:00 PM,
PT, Monday-Friday
If you’re scanning slides, reverse the film holder so the 35 mm slide
holders are toward the center and the film strip holder is aligned with the
right edge of the scanner glass. Then place the slides in the holder.
Copy
EPSON Scan
Scan to Web
Internet and E-mail
Film strip holder
Click Color
Restoration
Scan to E-mail
Fax
Color restoration is available in Home and Professional modes.
1
To select Color Restoration,
start EPSON Scan.
You see a screen
similar to this.
EPSON Smart
Panel
(510) 445-8616
Adobe
Photoshop
Elements
Windows
(206) 675-6358
(510) 445-8601
www.newsoftinc.com
tech@newsoftinc.com
www.adobe.com/support
Macintosh
(206) 675-6258
• You can start Smart Panel by clicking the
icon on your desktop,
and use it to perform various types of scans.
Problems?
• You can start EPSON Scan from Adobe Photoshop Elements or any
other TWAIN-compliant program. You can also start the EPSON Scan
program directly from your computer.
First, check the
Select Color
Restoration
5
Selecting the Scanning Mode
Note: You can also scan film and slides in Full Auto mode, although
you won’t have control over the settings.
EPSON Scan has three scanning modes:
2
Click the Preview button at the bottom of the screen.
• Full Auto Mode for automatic control
of scan settings.
3
Select the Color Restoration checkbox. (If you’re using Professional
Mode, you may need to scroll to the bottom of the screen.)
• Home Mode for more control over scan
settings, including Color Restoration.
• Professional Mode for full control
over all scan settings.
Start EPSON Scan and select either Home Mode or Professional Mode.
Scanning Film
The scanner cover has a built-in film transparancy unit. To scan film or negative
strips, slides, or transparencies, you need to remove the document mat from the
scanner cover and insert the film in a holder.
1
To change settings in Full Auto Mode, click the Pause button, then click
Options. If you’re using Home or Professional Mode, the options window
automatically appears. Then select the settings you want to use for your scan.
2
Note: The selected mode and settings remain in effect until they
are changed.
Flashing green
Warming up or scanning.
Green
Ready to scan.
Flashing red
Make sure the transportation lock is unlocked
(see section 3).
Home Mode: Select the correct Document Type: Color Negative Film,
B&W Negative Film, or Positive Film (for slides and transparencies).
Make sure the cable for the transparency unit is connected to the scanner
(see section 3). If you need to connect the cable, first disconnect the
scanner from the electrical outlet. After you have connected the cable,
plug the scanner back into the outlet.
Try restarting your computer and turning the
scanner off and then on again.
Professional Mode: Select Transparency as your Document Type.
Then select the Film Type: Color Negative Film, B&W Negative Film,
or Positive Film.
Tip: Make sure your film is dust-free
for the best scan. You can also select
the Dust Removal setting in EPSON
Scan, as shown.
If the red light is still flashing, contact your dealer
or EPSON.
Off
Click to lessen
the appearance
of dust
If your problem is listed here, try these suggestions.
You see a message about
a HI-SPEED USB device
in Windows XP.
Uninstall the following programs: EPSON Photo
Print, EPSON Scan, EPSON Smart Panel,
and ScanToWeb. In the Windows Control Panel,
use the Add/Remove Programs utility to uninstall
software. Then follow the instructions on the
other side of this sheet to reinstall your scanner
software.
Got Questions?
Here’s where to look for answers:
If you have faded photos or negatives, you can use the Color Restoration
setting in your software to improve the color of your scan. You can select this
setting in Smart Panel or in EPSON Scan.
On-screen Scanner Reference Guide
Double-click the Scanner Reference Guide icon on your desktop.
On-screen Help for Smart Panel and EPSON Scan
Click the Help button or question mark that appears on the screen when you’re
using these programs.
3
Locate the film holder that came with your scanner. Slide a strip of 35 mm
film into the film strip holder, with the film’s shiny side side facing down.
EPSON Technical Support
EPSON provides technical assistance 24 hours a day through the electronic
support services and automated telephone services described below:
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Automated Telephone Services
To use Automated Telephone Services, you must have a touch tone
telephone and call (800) 922-8911. Your EPSON SoundAdviceSM Express
Code is 70395. Use it to quickly select your scanner in SoundAdvice.
continue
Click the x in the corner of the message to
close it. Your scanner will work correctly,
although not at maximum speed.
You see an error message Make sure the scanner is connected to your
computer and plugged into a power source.
when you try to scan, or
the scanner doesn’t scan.
Make sure the transportation lock is pushed all
the way to the right (see section 3).
Open the scanner cover. Pull the handle for the document mat up slightly
until the handle is free of the cover, then pull the document mat forward
and out.
Restoring Color in Photos
Make sure your scanner is connected to your
computer and plugged into a working power source.
The New Hardware Wizard Click Cancel and follow the steps in “Install the
appears on your screen.
Software” on the other side of this sheet.
Disconnect the scanner before installing
the software.
Follow these steps to scan 35 mm film or slides:
To change the scanning mode, choose the mode you want to use from the
Mode list box at the top right of the window.
light on the scanner.
To Speak to a Technical Support Representative
Dial (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM, Pacific
Time, Monday through Friday. Toll or long distance charges may apply.
You can’t scan negatives
or slides.
Make sure the scanner film holder is positioned
correctly, and the scanner glass is clean.
Make sure the cable for the transparency unit is
connected to the scanner (see section 3) and the
reflective document mat is removed.
If you’re using Home or Professional mode,
make sure the Document Type or Film Type
matches what you’re scanning: either Color
Negative Film, B&W Negative Film, or Positive
Film (for slides and transparencies).
EPSON is a registered trademark and EPSON Smart Panel is a trademark of SEIKO EPSON
CORPORATION. EPSON Perfection is a registered trademark, and EPSON Store and SoundAdvice are
service marks of Epson America, Inc.
General Notice: Other product names are for identification purposes only and may be trademarks
of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. Printed on recycled paper. 6/03
Printed in XXX
CPD-14017R2
4025689-02
Starting a Scan
Smart Panel
1
To select the Color Restoration setting, open Smart Panel and select
Reprint Photo. You see the screen below.
2
Click the Color Restoration icon.
You can start a scan in several different ways:
• You can use the scanner buttons. Press the button for the type of scan
you want. Smart Panel automatically opens and scans your documents.
Then follow the easy on-screen instructions to finish your task.
4
Place the film holder on the scanner as shown. The film strip side of the
holder should be toward the center, and the 35 mm slide holders should
be aligned with the right edge of the scanner glass.
To Purchase an Optional Film Adapter or Other Accessories
Call the EPSON StoreSM at (800) 873-7766 or visit our web site at
www.epsonstore.com (U.S. sales only). In Canada, please call (800) 873-7766
for dealer referral.
Software Technical Support
If you’re having problems with your software, use the contact information below.
Slide holders
Note: If you are using Windows XP, you will have to select EPSON
Smart Panel and Always use this program for this action the
first time you press each of the buttons.
Software
Telephone
EPSON Scan
U.S.
(562) 276-4382
support.epson.com
Canada
(905) 709-3839
Start
Click here to
scan and print
6:00 AM to 6:00 PM,
PT, Monday-Friday
If you’re scanning slides, reverse the film holder so the 35 mm slide
holders are toward the center and the film strip holder is aligned with the
right edge of the scanner glass. Then place the slides in the holder.
Copy
EPSON Scan
Scan to Web
Internet and E-mail
Film strip holder
Click Color
Restoration
Scan to E-mail
Fax
Color restoration is available in Home and Professional modes.
1
To select Color Restoration,
start EPSON Scan.
You see a screen
similar to this.
EPSON Smart
Panel
(510) 445-8616
Adobe
Photoshop
Elements
Windows
(206) 675-6358
(510) 445-8601
www.newsoftinc.com
tech@newsoftinc.com
www.adobe.com/support
Macintosh
(206) 675-6258
• You can start Smart Panel by clicking the
icon on your desktop,
and use it to perform various types of scans.
Problems?
• You can start EPSON Scan from Adobe Photoshop Elements or any
other TWAIN-compliant program. You can also start the EPSON Scan
program directly from your computer.
Select Color
Restoration
Selecting the Scanning Mode
EPSON Scan has three scanning modes:
Click the Preview button at the bottom of the screen.
• Full Auto Mode for automatic control
of scan settings.
3
Select the Color Restoration checkbox. (If you’re using Professional
Mode, you may need to scroll to the bottom of the screen.)
• Professional Mode for full control
over all scan settings.
Start EPSON Scan and select either Home Mode or Professional Mode.
Note: You can also scan film and slides in Full Auto mode, although
you won’t have control over the settings.
2
• Home Mode for more control over scan
settings, including Color Restoration.
First, check the
5
Scanning Film
The scanner cover has a built-in film transparancy unit. To scan film or negative
strips, slides, or transparencies, you need to remove the document mat from the
scanner cover and insert the film in a holder.
1
To change settings in Full Auto Mode, click the Pause button, then click
Options. If you’re using Home or Professional Mode, the options window
automatically appears. Then select the settings you want to use for your scan.
2
Note: The selected mode and settings remain in effect until they
are changed.
Make sure the cable for the transparency unit is connected to the scanner
(see section 3). If you need to connect the cable, first disconnect the
scanner from the electrical outlet. After you have connected the cable,
plug the scanner back into the outlet.
Flashing green
Warming up or scanning.
Green
Ready to scan.
Flashing red
Make sure the transportation lock is unlocked
(see section 3).
Home Mode: Select the correct Document Type: Color Negative Film,
B&W Negative Film, or Positive Film (for slides and transparencies).
Try restarting your computer and turning the
scanner off and then on again.
Professional Mode: Select Transparency as your Document Type.
Then select the Film Type: Color Negative Film, B&W Negative Film,
or Positive Film.
Tip: Make sure your film is dust-free
for the best scan. You can also select
the Dust Removal setting in EPSON
Scan, as shown.
If the red light is still flashing, contact your dealer
or EPSON.
Off
Click to lessen
the appearance
of dust
If your problem is listed here, try these suggestions.
You see a message about
a HI-SPEED USB device
in Windows XP.
Uninstall the following programs: EPSON Photo
Print, EPSON Scan, EPSON Smart Panel,
and ScanToWeb. In the Windows Control Panel,
use the Add/Remove Programs utility to uninstall
software. Then follow the instructions on the
other side of this sheet to reinstall your scanner
software.
Got Questions?
Here’s where to look for answers:
If you have faded photos or negatives, you can use the Color Restoration
setting in your software to improve the color of your scan. You can select this
setting in Smart Panel or in EPSON Scan.
On-screen Scanner Reference Guide
Double-click the Scanner Reference Guide icon on your desktop.
On-screen Help for Smart Panel and EPSON Scan
Click the Help button or question mark that appears on the screen when you’re
using these programs.
3
Locate the film holder that came with your scanner. Slide a strip of 35 mm
film into the film strip holder, with the film’s shiny side side facing down.
Click the x in the corner of the message to
close it. Your scanner will work correctly,
although not at maximum speed.
You see an error message Make sure the scanner is connected to your
computer and plugged into a power source.
when you try to scan, or
the scanner doesn’t scan.
Make sure the transportation lock is pushed all
the way to the right (see section 3).
Open the scanner cover. Pull the handle for the document mat up slightly
until the handle is free of the cover, then pull the document mat forward
and out.
Restoring Color in Photos
Make sure your scanner is connected to your
computer and plugged into a working power source.
The New Hardware Wizard Click Cancel and follow the steps in “Install the
appears on your screen.
Software” on the other side of this sheet.
Disconnect the scanner before installing
the software.
Follow these steps to scan 35 mm film or slides:
To change the scanning mode, choose the mode you want to use from the
Mode list box at the top right of the window.
light on the scanner.
EPSON Technical Support
EPSON provides technical assistance 24 hours a day through the electronic
support services and automated telephone services described below:
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Automated Telephone Services
To use Automated Telephone Services, you must have a touch tone
telephone and call (800) 922-8911. Your EPSON SoundAdviceSM Express
Code is 70395. Use it to quickly select your scanner in SoundAdvice.
To Speak to a Technical Support Representative
Dial (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM, Pacific
Time, Monday through Friday. Toll or long distance charges may apply.
You can’t scan negatives
or slides.
Make sure the scanner film holder is positioned
correctly, and the scanner glass is clean.
Make sure the cable for the transparency unit is
connected to the scanner (see section 3) and the
reflective document mat is removed.
If you’re using Home or Professional mode,
make sure the Document Type or Film Type
matches what you’re scanning: either Color
Negative Film, B&W Negative Film, or Positive
Film (for slides and transparencies).
EPSON is a registered trademark and EPSON Smart Panel is a trademark of SEIKO EPSON
CORPORATION. EPSON Perfection is a registered trademark, and EPSON Store and SoundAdvice are
service marks of Epson America, Inc.
General Notice: Other product names are for identification purposes only and may be trademarks
of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. Printed on recycled paper. 6/03
Printed in XXX
CPD-14017R2
4025689-02
Starting a Scan
Smart Panel
1
To select the Color Restoration setting, open Smart Panel and select
Reprint Photo. You see the screen below.
2
Click the Color Restoration icon.
You can start a scan in several different ways:
• You can use the scanner buttons. Press the button for the type of scan
you want. Smart Panel automatically opens and scans your documents.
Then follow the easy on-screen instructions to finish your task.
4
Place the film holder on the scanner as shown. The film strip side of the
holder should be toward the center, and the 35 mm slide holders should
be aligned with the right edge of the scanner glass.
To Purchase an Optional Film Adapter or Other Accessories
Call the EPSON StoreSM at (800) 873-7766 or visit our web site at
www.epsonstore.com (U.S. sales only). In Canada, please call (800) 873-7766
for dealer referral.
Software Technical Support
If you’re having problems with your software, use the contact information below.
Slide holders
Note: If you are using Windows XP, you will have to select EPSON
Smart Panel and Always use this program for this action the
first time you press each of the buttons.
Software
Telephone
EPSON Scan
U.S.
(562) 276-4382
support.epson.com
Canada
(905) 709-3839
Start
Click here to
scan and print
6:00 AM to 6:00 PM,
PT, Monday-Friday
If you’re scanning slides, reverse the film holder so the 35 mm slide
holders are toward the center and the film strip holder is aligned with the
right edge of the scanner glass. Then place the slides in the holder.
Copy
EPSON Scan
Scan to Web
Internet and E-mail
Film strip holder
Click Color
Restoration
Scan to E-mail
Fax
Color restoration is available in Home and Professional modes.
1
To select Color Restoration,
start EPSON Scan.
You see a screen
similar to this.
EPSON Smart
Panel
(510) 445-8616
Adobe
Photoshop
Elements
Windows
(206) 675-6358
(510) 445-8601
www.newsoftinc.com
tech@newsoftinc.com
www.adobe.com/support
Macintosh
(206) 675-6258
• You can start Smart Panel by clicking the
icon on your desktop,
and use it to perform various types of scans.
Problems?
• You can start EPSON Scan from Adobe Photoshop Elements or any
other TWAIN-compliant program. You can also start the EPSON Scan
program directly from your computer.
Select Color
Restoration
Selecting the Scanning Mode
EPSON Scan has three scanning modes:
Click the Preview button at the bottom of the screen.
• Full Auto Mode for automatic control
of scan settings.
3
Select the Color Restoration checkbox. (If you’re using Professional
Mode, you may need to scroll to the bottom of the screen.)
• Professional Mode for full control
over all scan settings.
Start EPSON Scan and select either Home Mode or Professional Mode.
Note: You can also scan film and slides in Full Auto mode, although
you won’t have control over the settings.
2
• Home Mode for more control over scan
settings, including Color Restoration.
First, check the
5
Scanning Film
The scanner cover has a built-in film transparancy unit. To scan film or negative
strips, slides, or transparencies, you need to remove the document mat from the
scanner cover and insert the film in a holder.
1
To change settings in Full Auto Mode, click the Pause button, then click
Options. If you’re using Home or Professional Mode, the options window
automatically appears. Then select the settings you want to use for your scan.
2
Note: The selected mode and settings remain in effect until they
are changed.
Make sure the cable for the transparency unit is connected to the scanner
(see section 3). If you need to connect the cable, first disconnect the
scanner from the electrical outlet. After you have connected the cable,
plug the scanner back into the outlet.
Flashing green
Warming up or scanning.
Green
Ready to scan.
Flashing red
Make sure the transportation lock is unlocked
(see section 3).
Home Mode: Select the correct Document Type: Color Negative Film,
B&W Negative Film, or Positive Film (for slides and transparencies).
Try restarting your computer and turning the
scanner off and then on again.
Professional Mode: Select Transparency as your Document Type.
Then select the Film Type: Color Negative Film, B&W Negative Film,
or Positive Film.
Tip: Make sure your film is dust-free
for the best scan. You can also select
the Dust Removal setting in EPSON
Scan, as shown.
If the red light is still flashing, contact your dealer
or EPSON.
Off
Click to lessen
the appearance
of dust
If your problem is listed here, try these suggestions.
You see a message about
a HI-SPEED USB device
in Windows XP.
Uninstall the following programs: EPSON Photo
Print, EPSON Scan, EPSON Smart Panel,
and ScanToWeb. In the Windows Control Panel,
use the Add/Remove Programs utility to uninstall
software. Then follow the instructions on the
other side of this sheet to reinstall your scanner
software.
Got Questions?
Here’s where to look for answers:
If you have faded photos or negatives, you can use the Color Restoration
setting in your software to improve the color of your scan. You can select this
setting in Smart Panel or in EPSON Scan.
On-screen Scanner Reference Guide
Double-click the Scanner Reference Guide icon on your desktop.
On-screen Help for Smart Panel and EPSON Scan
Click the Help button or question mark that appears on the screen when you’re
using these programs.
3
Locate the film holder that came with your scanner. Slide a strip of 35 mm
film into the film strip holder, with the film’s shiny side side facing down.
Click the x in the corner of the message to
close it. Your scanner will work correctly,
although not at maximum speed.
You see an error message Make sure the scanner is connected to your
computer and plugged into a power source.
when you try to scan, or
the scanner doesn’t scan.
Make sure the transportation lock is pushed all
the way to the right (see section 3).
Open the scanner cover. Pull the handle for the document mat up slightly
until the handle is free of the cover, then pull the document mat forward
and out.
Restoring Color in Photos
Make sure your scanner is connected to your
computer and plugged into a working power source.
The New Hardware Wizard Click Cancel and follow the steps in “Install the
appears on your screen.
Software” on the other side of this sheet.
Disconnect the scanner before installing
the software.
Follow these steps to scan 35 mm film or slides:
To change the scanning mode, choose the mode you want to use from the
Mode list box at the top right of the window.
light on the scanner.
EPSON Technical Support
EPSON provides technical assistance 24 hours a day through the electronic
support services and automated telephone services described below:
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Automated Telephone Services
To use Automated Telephone Services, you must have a touch tone
telephone and call (800) 922-8911. Your EPSON SoundAdviceSM Express
Code is 70395. Use it to quickly select your scanner in SoundAdvice.
To Speak to a Technical Support Representative
Dial (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM, Pacific
Time, Monday through Friday. Toll or long distance charges may apply.
You can’t scan negatives
or slides.
Make sure the scanner film holder is positioned
correctly, and the scanner glass is clean.
Make sure the cable for the transparency unit is
connected to the scanner (see section 3) and the
reflective document mat is removed.
If you’re using Home or Professional mode,
make sure the Document Type or Film Type
matches what you’re scanning: either Color
Negative Film, B&W Negative Film, or Positive
Film (for slides and transparencies).
EPSON is a registered trademark and EPSON Smart Panel is a trademark of SEIKO EPSON
CORPORATION. EPSON Perfection is a registered trademark, and EPSON Store and SoundAdvice are
service marks of Epson America, Inc.
General Notice: Other product names are for identification purposes only and may be trademarks
of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2003 by Epson America, Inc. Printed on recycled paper. 6/03
Printed in XXX
CPD-14017R2
4025689-02
Download PDF

advertising