Epson PowerLite 61p, 81p data projector Quick Setup

Epson PowerLite 81p: Experience dynamic presentations with this versatile projector, designed to deliver crisp, vibrant images in various settings. Connect your laptop or other devices effortlessly via the computer port and unleash your content on the big screen. The projector's user-friendly interface and intuitive controls allow for seamless navigation and adjustments during your presentations. Engage your audience with sharp, detailed visuals and make a lasting impression with the Epson PowerLite 81p.

PDF Download

Document

Epson PowerLite 61p/81p
&reg;
&reg;
Quick Setup
TART
HERE
Connect the projector
to your notebook
S
1
Locate the required cables:
Power cord
2
3
Computer cable
Connect the computer cable to the
Computer 1/Component Video 1
port on the projector.
Connect the other end to your notebook’s video-out
or
monitor port.
NOTE: If your notebook has a DVI connector, you need to either
connect a DVI-to-VGA adapter to the included computer cable (see
your computer’s documentation), or purchase an optional DVI to
VGA cable (for a higher-quality image). See your User’s Guide.
4
Connect the power cord to the
projector, then plug the other end
into a grounded electrical outlet.
Adjust the image
Turn on your equipment
1
1
2
Remove the projector’s lens cover.
2
Rotate the focus ring to sharpen the image.
Make sure the
Power light
is orange and not flashing.
Focus ring
to sharpen
the image
Power light is orange
and not flashing
4
If you’ve turned on your notebook and you don’t see an image, press
the Source Search button on the projector to select the image source.
NOTE: If you still see a blank screen or have other display problems,
see the troubleshooting tips on the back of this sheet.
Turn on your notebook.
3
Follow these instructions to connect the projector to your
notebook. For other setup options, see your User’s Guide.
Power button
Press the
Power button
to turn on the projector.
The projector beeps and
the
Power light flashes
as the projector warms up.
3
CAUTION: Before unplugging the projector...
4
To shut down the projector properly:
1. Press the
Power button twice. The projector beeps twice, the lamp
turns off, and the
Power light flashes orange (about 60 seconds).
2. Once the light stops flashing and stays on, it’s safe to unplug
the projector.
Never unplug the projector when the
flashing orange.
Zoom ring
to adjust the
image size
Power light is green or
5
Rotate the zoom ring to reduce or enlarge the image. (You can also
move the projector closer to or farther from the screen.)
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the
center of the screen, facing the screen squarely.
If your image looks like
square up the image.
or
, use the
or
buttons to
Quick Setup
Epson PowerLite 61p/81p
&reg;
Using the remote control
1
2
If this is your first time using the
remote, press the tab in to release
the cover. Then remove the cover.
&reg;
Troubleshooting
If you see a blank screen...
If you see a blank screen or the No signal message after turning on
your notebook, check the following:
Insert the batteries as shown and
replace the battery cover.
Zoom in on part of
the projected image
Turn the projector
on and off
Navigate projector
menus and control
pointer
Turn off projector
display and sound
Choose which
source to display
Search for the
correct source
Make sure the
Power light on the projector is green
and not flashing, and the lens cover is off.
Press the Comp 1 button on the remote control
to select Computer 1 as the image source.
If you’re using a Windows&reg; notebook, press the function key on
your keyboard that lets you display on an external monitor. It may
be labelled CRT/LCD or have an icon such as
. You may have
to hold down the Fn key while pressing it. Allow a few seconds
for the projector to sync up after changing the setting.
If the projector and notebook
don’t display the same image...
If your image displays either on the projector or notebook, but not on
both, check the following:
Freeze the projector display
(presentation and sound
continue unless stopped)
Windows
Display projector
menus
Try using the CRT/LCD or
key as described above. On most systems,
this key lets you toggle between the LCD screen and the projector,
or display on both at the same time.
Control projector
volume
If that doesn’t work, check your monitor settings to make sure both the
LCD screen and the external monitor port are enabled.
With the USB cable included with the projector, you can use the remote as
a wireless mouse. For more information on the wireless mouse function
and on general use of the remote control, see your User’s Guide.
1.
From the Windows Control Panel, open the Display utility.
2.
In the Display Properties dialog box, click the
Settings tab, then click Advanced.
3.
The method for adjusting the setting varies;
you may have to click a Monitor tab, then
make sure the external Monitor port is set
as your primary display and/or enabled.
See your notebook’s manual or online help
for details.
NOTE: Put your remote in a safe place. You’ll need it if you use a
password with the projector. See the User’s Guide for details.
W here to get help
Telephone Support Services
To use the Epson PrivateLine&reg; Support service, call (800) 637-7661
and enter the PIN on the Epson PrivateLine Support card included
with your projector. This service is available 6 AM to 6 PM, Pacific Time,
Monday through Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing
one of these numbers:
Macintosh&reg; OS X
1.
From the Apple&reg; menu, select System
Preferences, then select Displays.
2.
Select the Color LCD dialog box.
3.
Click the Arrange (or Arrangement) tab
and click Mirror Displays.
Macintosh OS 9.x or earlier
1.
From the Apple menu, select Control
Panels, then click Monitors or
Monitors and Sound.
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
2.
Click the Arrange icon.
Toll or long distance charges may apply.
3.
Drag one monitor icon
on top of the other.
U.S.:
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Electronic Support Services
Epson provides technical assistance through electronic support
services 24 hours a day at http://support.epson.com. For tips,
templates, and training for developing successful presentations
go to http://www.presentersonline.com.
If the Arrange option isn’t available, click the
Monitor icon and select a Simulscan resolution.
Epson is a registered trademark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
Epson disclaims any and all rights in those marks. &copy; 2004 Epson America, Inc. 4/04
Printed in XXX
CPD-18000
">

Hello! I am an AI chatbot specifically trained to assist you with the Epson PowerLite 61p 81p data projector Quick Setup. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Easy setup with notebook
Source search button
Remote control with wireless mouse function
Image adjust tools: focus, zoom, and keystone correction

Frequently asked questions

Make sure the Power light on the projector is green and not flashing, the lens cover is off, and the correct source is selected. Try pressing the Comp 1 button on the remote to select Computer 1 as the image source. If using a Windows notebook, try pressing the Function key that lets you display on an external monitor.

Check the monitor settings to make sure both the LCD screen and the external monitor port are enabled. Try using the CRT/LCD key to toggle between the LCD screen and the projector, or display on both at the same time.

Press the Power button twice. The projector beeps twice, the lamp turns off, and the Power light flashes orange. Once the light stops flashing and stays on, it's safe to unplug the projector.