Service manual | Epson C2600/2600 Printer User Manual

Dell 2330d/dn
Service Manual
11 Dec 2008
Information in this document is subject to change without notice.
2010 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc.is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to the entities claiming the marks and
names of their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its
own.
Table of Contents
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Notices and safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Laser notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
General information
....................................................................
1-1
Maintenance approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview of the operator panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Print quality settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectivity and compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Media trays and supply capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of print media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tips on preventing jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paper path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-2
1-3
1-3
1-3
1-4
1-5
1-6
1-7
1-7
1-8
1-9
Diagnostics information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Overview of the operator panel and menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Indicator light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Diagram of the printer menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Messages and error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
User attendance messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Cartridge error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Paper jam error codes (200-series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Service error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Symptom tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
POST symptom table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Printer symptom table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Service checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Controller board service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Cooling fan service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Cover interlock switch service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Dead machine service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Fuser service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
LVPS/HVPS service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
Main motor service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Operator panel service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Paper feed service checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Parallel or USB port service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Print quality service checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Printhead service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Transfer roll service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Tray 2 service check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Table of Contents
iii
Diagnostic aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Accessing service menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Printing menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Configuration menu (CONFIG MENU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Entering Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Available menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Reset photoconductor maintenance counter (Reset PC Cnt) . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Print quality pages (Prt Quality Pgs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Panel Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
PPDS Emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Energy Conserve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Font Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Exit Configuration Menu (Exit Config Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Entering Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Available tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
Print tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Hardware tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
Duplex tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Input tray tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Output bin tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Base sensor test (B. sensor test) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Printer setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
EP setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
Event log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
Exit Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
Printhead assembly electronic adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
Printhead assembly mechanical adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17
Repair information
.....................................................................
4-1
Handling ESD-sensitive parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Removal procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
ACM pick tire roller removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Bezel removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Controller board removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Cover open sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
Door mount removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Duplex removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Duplex/main motor gear drive interface removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13
Fan removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-16
Front access door removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-17
Fuser removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
Left side cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-23
Lower front cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25
LVPS/HVPS removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27
Main motor gear drive removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-30
Manual feed clutch removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-32
Manual feed solenoid removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-34
Media ACM ASM feeder removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37
Media feed clutch with cable removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-40
Media manual input sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-42
Multipurpose feeder (MPF) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-45
Multipurpose feeder (MPF) feed clutch removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-48
Nameplate removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-50
iv
Operator panel removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paper input and duplex sensor assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printhead removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear door and rear cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear exit guide assembly with sensor and reversing solenoid removal . . . . . . . . . . . . . . . . . .
Right side cover assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toner level sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top cover assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer roll removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper front guide assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wear strip (tray 1 and 250-sheet tray 2) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wear strip (550-sheet tray 2) removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-51
4-52
4-53
4-54
4-56
4-58
4-60
4-61
4-63
4-64
4-65
4-66
Locations and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller board connector pin values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5-1
5-1
5-2
Preventive maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Safety inspection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Lubrication specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Parts catalog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
How to use this parts catalog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1
Part number index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-3
Table of Contents
v
vi
Notices and safety information
The following laser notice labels may be affixed to this printer.
Laser notice
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1)
laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC
60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser
that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength region of 655-675 nanometers.
The laser system and printer are designed so there is never any human access to laser radiation above a Class
I level during normal operation, user maintenance, or prescribed service condition.
Laser
Der Drucker erfüllt gemäß amtlicher Bestätigung der USA die Anforderungen der Bestimmung DHHS
(Department of Health and Human Services) 21 CFR Teil J für Laserprodukte der Klasse I (1). In anderen
Ländern gilt der Drucker als Laserprodukt der Klasse I, der die Anforderungen der IEC (International
Electrotechnical Commission) 60825-1 gemäß amtlicher Bestätigung erfüllt.
Laserprodukte der Klasse I gelten als unschädlich. Im Inneren des Druckers befindet sich ein Laser der Klasse
IIIb (3b), bei dem es sich um einen Galliumarsenlaser mit 7 Milliwatt handelt, der Wellen der Länge 655-675
Nanometer ausstrahlt. Das Lasersystem und der Drucker sind so konzipiert, daß im Normalbetrieb, bei der
Wartung durch den Benutzer oder bei ordnungsgemäßer Wartung durch den Kundendienst Laserbestrahlung,
die Klasse I übersteigen würde, Menschen keinesfalls erreicht.
Avis relatif à l’utilisation de laser
Pour les Etats-Unis : cette imprimante est certifiée conforme aux provisions DHHS 21 CFR alinéa J concernant
les produits laser de Classe I (1). Pour les autres pays : cette imprimante répond aux normes IEC 60825-1
relatives aux produits laser de Classe I.
Les produits laser de Classe I sont considérés comme des produits non dangereux. Cette imprimante est
équipée d’un laser de Classe IIIb (3b) (arséniure de gallium d’une puissance nominale de 7 milliwatts) émettant
sur des longueurs d’onde comprises entre 655 et 675 nanomètres. L’imprimante et son système laser sont
conçus pour impossible, dans des conditions normales d’utilisation, d’entretien par l’utilisateur ou de révision,
l’exposition à des rayonnements laser supérieurs à des rayonnements de Classe I .
Avvertenze sui prodotti laser
Questa stampante è certificata negli Stati Uniti per essere conforme ai requisiti del DHHS 21 CFR Sottocapitolo
J per i prodotti laser di classe 1 ed è certificata negli altri Paesi come prodotto laser di classe 1 conforme ai
requisiti della norma CEI 60825-1.
I prodotti laser di classe non sono considerati pericolosi. La stampante contiene al suo interno un laser di classe
IIIb (3b) all’arseniuro di gallio della potenza di 7mW che opera sulla lunghezza d’onda compresa tra 655 e 675
nanometri. Il sistema laser e la stampante sono stati progettati in modo tale che le persone a contatto con la
stampante, durante il normale funzionamento, le operazioni di servizio o quelle di assistenza tecnica, non
ricevano radiazioni laser superiori al livello della classe 1.
Notices and safety information
vii
Avisos sobre el láser
Se certifica que, en los EE.UU., esta impresora cumple los requisitos para los productos láser de Clase I (1)
establecidos en el subcapítulo J de la norma CFR 21 del DHHS (Departamento de Sanidad y Servicios) y, en
los demás países, reúne todas las condiciones expuestas en la norma IEC 60825-1 para productos láser de
Clase I (1).
Los productos láser de Clase I no se consideran peligrosos. La impresora contiene en su interior un láser de
Clase IIIb (3b) de arseniuro de galio de funcionamiento nominal a 7 milivatios en una longitud de onda de 655 a
675 nanómetros. El sistema láser y la impresora están diseñados de forma que ninguna persona pueda verse
afectada por ningún tipo de radiación láser superior al nivel de la Clase I durante su uso normal, el
mantenimiento realizado por el usuario o cualquier otra situación de servicio técnico.
Declaração sobre Laser
A impressora está certificada nos E.U.A. em conformidade com os requisitos da regulamentação DHHS 21 CFR
Subcapítulo J para a Classe I (1) de produtos laser. Em outros locais, está certificada como um produto laser da
Classe I, em conformidade com os requisitos da norma IEC 60825-1.
Os produtos laser da Classe I não são considerados perigosos. Internamente, a impressora contém um produto
laser da Classe IIIb (3b), designado laser de arseneto de potássio, de 7 milliwatts ,operando numa faixa de
comprimento de onda entre 655 e 675 nanómetros. O sistema e a impressora laser foram concebidos de forma
a nunca existir qualquer possiblidade de acesso humano a radiação laser superior a um nível de Classe I
durante a operação normal, a manutenção feita pelo utilizador ou condições de assistência prescritas.
Laserinformatie
De printer voldoet aan de eisen die gesteld worden aan een laserprodukt van klasse I. Voor de Verenigde
Staten zijn deze eisen vastgelegd in DHHS 21 CFR Subchapter J, voor andere landen in IEC 60825-1.
Laserprodukten van klasse I worden niet als ongevaarlijk aangemerkt. De printer is voorzien van een laser van
klasse IIIb (3b), dat wil zeggen een gallium arsenide-laser van 7 milliwatt met een golflengte van 655-675
nanometer. Het lasergedeelte en de printer zijn zo ontworpen dat bij normaal gebruik, bij onderhoud of reparatie
conform de voorschriften, nooit blootstelling mogelijk is aan laserstraling boven een niveau zoals
voorgeschreven is voor klasse 1.
Lasermeddelelse
Printeren er godkendt som et Klasse I-laserprodukt, i overenstemmelse med kravene i IEC 60825-1.
Klasse I-laserprodukter betragtes ikke som farlige. Printeren indeholder internt en Klasse IIIB (3b)-laser, der
nominelt er en 7 milliwatt galliumarsenid laser, som arbejder på bølgelængdeområdet 655-675 nanometer.
Lasersystemet og printeren er udformet således, at mennesker aldrig udsættes for en laserstråling over Klasse
I-niveau ved normal drift, brugervedligeholdelse eller obligatoriske servicebetingelser.
viii
Laserilmoitus
Tämä tulostin on sertifioitu Yhdysvalloissa DHHS 21 CFR Subchapter J -standardin mukaiseksi luokan I (1) lasertuotteeksi ja muualla IEC 60825-1 -standardin mukaiseksi luokan I lasertuotteeksi.
Luokan I lasertuotteita ei pidetä haitallisina. Tulostimen sisällä on luokan IIIb (3b) laser, joka on nimellisteholtaan
7 mW:n galliumarsenidilaser ja toimii 655 - 675 nanometrin aallonpituuksilla. Laserjärjestelmä ja tulostin ovat
rakenteeltaan sellaisia, että käyttäjä ei joudu alttiiksi luokkaa 1 suuremmalle säteilylle normaalin käytön,
ylläpidon tai huollon aikana.
Huomautus laserlaitteesta
Tämä kirjoitin on Yhdysvalloissa luokan I (1) laserlaitteiden DHHS 21 CFR Subchapter J -määrityksen mukainen
ja muualla luokan I laserlaitteiden IEC 60825-1 -määrityksen mukainen.
Luokan I laserlaitteiden ei katsota olevan vaarallisia käyttäjälle. Kirjoittimessa on sisäinen luokan IIIb (3b) 7
milliwatin galliumarsenidilaser, joka toimii aaltoalueella 655 - 675 nanometriä. Laserjärjestelmä ja kirjoitin on
suunniteltu siten, että käyttäjä ei altistu luokan I määrityksiä voimakkaammalle säteilylle kirjoittimen normaalin
toiminnan, käyttäjän tekemien huoltotoimien tai muiden huoltotoimien yhteydessä.
VARO! Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso
säteeseen.
VARNING! Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad.
Betrakta ej strålen.
Laser-notis
Denna skrivare är i USA certifierad att motsvara kraven i DHHS 21 CFR, underparagraf J för laserprodukter av
Klass I (1). I andra länder uppfyller skrivaren kraven för laserprodukter av Klass I enligt kraven i IEC 60825-1.
Laserprodukter i Klass I anses ej hälsovådliga. Skrivaren har en inbyggd laser av Klass IIIb (3b) som består av
en laserenhet av gallium-arsenid på 7 milliwatt som arbetar i våglängdsområdet 655-675 nanometer.
Lasersystemet och skrivaren är utformade så att det aldrig finns risk för att någon person utsätts för
laserstrålning över Klass I-nivå vid normal användning, underhåll som utförs av användaren eller annan
föreskriven serviceåtgärd.
Laser-melding
Skriveren er godkjent i USA etter kravene i DHHS 21 CFR, underkapittel J, for klasse I (1) laserprodukter, og er
i andre land godkjent som et Klasse I-laserprodukt i samsvar med kravene i IEC 60825-1.
Klasse I-laserprodukter er ikke å betrakte som farlige. Skriveren inneholder internt en klasse IIIb (3b)-laser, som
består av en gallium-arsenlaserenhet som avgir stråling i bølgelengdeområdet 655-675 nanometer.
Lasersystemet og skriveren er utformet slik at personer aldri utsettes for laserstråling ut over klasse I-nivå under
vanlig bruk, vedlikehold som utføres av brukeren, eller foreskrevne serviceoperasjoner.
Notices and safety information
ix
Avís sobre el Làser
Segons ha estat certificat als Estats Units, aquesta impressora compleix els requisits de DHHS 21 CFR, apartat
J, pels productes làser de classe I (1), i segons ha estat certificat en altres llocs, és un producte làser de classe
I que compleix els requisits d’IEC 60825-1.
Els productes làser de classe I no es consideren perillosos. Aquesta impressora conté un làser de classe IIIb
(3b) d’arseniür de gal.li, nominalment de 7 mil.liwats, i funciona a la regió de longitud d’ona de 655-675
nanòmetres. El sistema làser i la impressora han sigut concebuts de manera que mai hi hagi exposició a la
radiació làser per sobre d’un nivell de classe I durant una operació normal, durant les tasques de manteniment
d’usuari ni durant els serveis que satisfacin les condicions prescrites.
x
Notices and safety information
xi
xii
Safety information
• The safety of this product is based on testing and approvals of the original design and specific
•
•
•
components. The manufacturer is not responsible for safety in the event of use of unauthorized
replacement parts.
The maintenance information for this product has been prepared for use by a professional service person
and is not intended to be used by others.
There may be an increased risk of electric shock and personal injury during disassembly and servicing of
this product. Professional service personnel should understand this and take necessary precautions.
CAUTION: When you see this symbol, there is a danger from hazardous voltage in the area of the
product where you are working. Unplug the product before you begin, or use caution if the product
must receive power in order to perform the task.
Consignes de sécurité
• La sécurité de ce produit repose sur des tests et des
•
•
•
agréations portant sur sa conception d'origine et sur des composants particuliers. Le fabricant n'assume
aucune responsabilité concernant la sécurité en cas d'utilisation de pièces de rechange non agréées.
Les consignes d'entretien et de réparation de ce produit s'adressent uniquement à un personnel de
maintenance qualifié.
Le démontage et l'entretien de ce produit pouvant présenter certains risques électriques, le personnel
d'entretien qualifié devra prendre toutes les précautions nécessaires.
ATTENTION : Ce symbole indique la présence d'une tension dangereuse dans la partie du
produit sur laquelle vous travaillez. Débranchez le produit avant de commencer ou faites preuve
de vigilance si l'exécution de la tâche exige que le produit reste sous tension.
Norme di sicurezza
• La sicurezza del prodotto si basa sui test e sull'approvazione del progetto originale e dei componenti
•
•
•
specifici. Il produttore non è responsabile per la sicurezza in caso di sostituzione non autorizzata delle
parti.
Le informazioni riguardanti la manutenzione di questo prodotto sono indirizzate soltanto al personale di
assistenza autorizzato.
Durante lo smontaggio e la manutenzione di questo prodotto,
il rischio di subire scosse elettriche e danni alla persona è più elevato. Il personale di assistenza
autorizzato deve, quindi, adottare le precauzioni necessarie.
ATTENZIONE: Questo simbolo indica la presenza di tensione pericolosa nell'area del prodotto.
Scollegare il prodotto prima di iniziare o usare cautela se il prodotto deve essere alimentato per
eseguire l'intervento.
Sicherheitshinweise
• Die Sicherheit dieses Produkts basiert auf Tests und Zulassungen des ursprünglichen Modells und
•
•
bestimmter Bauteile. Bei Verwendung nicht genehmigter Ersatzteile wird vom Hersteller keine
Verantwortung oder Haftung für die Sicherheit übernommen.
Die Wartungsinformationen für dieses Produkt sind ausschließlich für die Verwendung durch einen
Wartungsfachmann bestimmt.
Während des Auseinandernehmens und der Wartung des Geräts besteht ein zusätzliches Risiko eines
elektrischen Schlags und körperlicher Verletzung. Das zuständige Fachpersonal sollte entsprechende
Vorsichtsmaßnahmen treffen.
Safety information
xiii
•
ACHTUNG: Dieses Symbol weist auf eine gefährliche elektrische Spannung hin, die in diesem
Bereich des Produkts auftreten kann. Ziehen Sie vor den Arbeiten am Gerät den Netzstecker des
Geräts, bzw. arbeiten Sie mit großer Vorsicht, wenn das Produkt für die Ausführung der Arbeiten
an den Strom angeschlossen sein muß.
Pautas de Seguridad
• La seguridad de este producto se basa en pruebas y aprobaciones del diseño original y componentes
•
•
•
específicos. El fabricante no es responsable de la seguridad en caso de uso de piezas de repuesto no
autorizadas.
La información sobre el mantenimiento de este producto está dirigida exclusivamente al personal
cualificado de mantenimiento.
Existe mayor riesgo de descarga eléctrica y de daños personales durante el desmontaje y la reparación de
la máquina. El personal cualificado debe ser consciente de este peligro y tomar las precauciones
necesarias.
PRECAUCIÓN: este símbolo indica que el voltaje de la parte del equipo con la que está
trabajando es peligroso. Antes de empezar, desenchufe el equipo o tenga cuidado si, para
trabajar con él, debe conectarlo.
Informações de Segurança
• A segurança deste produto baseia-se em testes e aprovações do modelo original e de componentes
•
•
•
xiv
específicos. O fabricante não é responsável pela segunrança, no caso de uso de peças de substituição
não autorizadas.
As informações de segurança relativas a este produto destinam-se a profissionais destes serviços e não
devem ser utilizadas por outras pessoas.
Risco de choques eléctricos e ferimentos graves durante a desmontagem e manutenção deste produto.
Os profissionais destes serviços devem estar avisados deste facto e tomar os cuidados necessários.
CUIDADO: Quando vir este símbolo, existe a possível presença de uma potencial tensão
perigosa na zona do produto em que está a trabalhar. Antes de começar, desligue o produto da
tomada eléctrica ou seja cuidadoso caso o produto tenha de estar ligado à corrente eléctrica para
realizar a tarefa necessária.
Informació de Seguretat
• La seguretat d'aquest producte es basa en l'avaluació i aprovació del disseny original i els components
•
•
•
específics.
El fabricant no es fa responsable de les qüestions de
seguretat si s'utilitzen peces de recanvi no autoritzades.
La informació pel manteniment d’aquest producte està orientada exclusivament a professionals i no està
destinada
a ningú que no ho sigui.
El risc de xoc elèctric i de danys personals pot augmentar durant el procés de desmuntatge i de servei
d’aquest producte. El personal professional ha d’estar-ne assabentat i prendre
les mesures convenients.
PRECAUCIÓ: aquest símbol indica que el voltatge de la part de l'equip amb la qual esteu
treballant és perillós. Abans de començar, desendolleu l'equip o extremeu les precaucions si, per
treballar amb l'equip, l'heu de connectar.
Safety information
xv
Preface
This manual contains maintenance procedures for service personnel. It is divided into the following chapters:
1. General information contains a general description of the printer and the maintenance approach used to
2.
3.
4.
5.
6.
7.
repair it. Special tools and test equipment, as well as general environmental and safety instructions, are
discussed.
Diagnostic information contains an error indicator table, symptom tables, and service checks used to
isolate failing field replaceable units (FRUs).
Diagnostic aids contains tests and checks used to locate or repeat symptoms of printer problems.
Repair information provides instructions for making printer adjustments and removing and installing
FRUs.
Connector locations uses illustrations to identify the connector locations and test points on the printer.
Preventive maintenance contains the lubrication specifications and recommendations to prevent
problems.
Parts catalog contains illustrations and part numbers for individual FRUs.
Conventions
Note: A note provides additional information.
Warning: A warning identifies something that might damage the product hardware or software.
There are several types of caution statements:
CAUTION
A caution identifies something that might cause a servicer harm.
CAUTION
This type of caution indicates there is a danger from hazardous voltage in the area of the
product where you are working. Unplug the product before you begin, or use caution if the
product must receive power in order to perform the task.
CAUTION
This type of caution indicates a hot surface.
CAUTION
This type of caution indicates a tipping hazard.
xvi
1. General information
The Dell 2330d and Dell 2330dn are monochrome laser printers designed for single users or small
workgroups.
Maintenance approach
The diagnostic information in this manual leads to the correct field replaceable unit (FRU) or part. Use the error
code charts, symptom index, and service checks to determine the symptom and repair the failure. See
“Diagnostics information” on page 2-1 for more information. See “Repair information” on page 4-1 to help
identify parts. After completing the repair, perform tests as needed to verify the repair.
General information
1-1
Overview of the operator panel
The operator panel consists of these items:
• A 2-line liquid crystal display (LCD) that shows text
• Six buttons: Menus
, Back
,Navigation (with Left Menu
•
, Select
Stop
An indicator light
Menus
Back
1-2
Stop
and Right Menu
), and
Specifications
Memory
Item
Dell 2330d
Dell 2330dn
Standard memory
32MB
32MB
Maximum memory
288MB
288MB
128MB
✔
✔
256MB
✔
✔
512MB
x
x
64MB
✔
✔
256MB
x
x
Optional font cards (DBCS)
✔
✔
Memory slots
1
1
Flash memory/option card
2¹
2¹
Dell 2330d
Dell 2330dn
Optional memory
Optional flash memory
Option slots
¹ Only one slot is active for 64MB flash memory or font card.
Print quality settings
Item
Print resolution
1200 Image quality¹
✔
✔
2400 Image quality²
✔
✔
600 X 600 dpi
✔
✔
1200 X 1200 dpi³
✔
✔
¹ 1200 Image quality is defined as 600 dpi with 2 bit IET (Image Technology) default mode for all models.
² 2400 Image quality is defined as 600 dpi with 4 bit IET.
³ True 1200 dpi at 1/2 the rated speed
General information
1-3
Connectivity and compatibility
Item
Dell 2330d
Dell 2330dn
Data stream emulations
Host based printing
✔
✔
PCL 5e and PCL 6
✔
✔
PostScript 3
✔
✔
PPDS migration tool
✔
✔
PDF v1.6
x
x
XPS¹
x
x
HTML (including DBCS)
x
x
Direct image
x
x
Compatibility
Windows/Macintosh/Linux
Windows/Macintosh/Linux
Parallel
✔
✔
USB*
✔
✔
Ethernet (10/100 Base Tx)
x
✔
Wireless ethernet 802.11b/g/n
x
x
✔
✔
Standard local connections
Standard network connections
Optional local connections
Optional network connections:
external print server support
*All models are USB 2.0 Certified devices supporting Hi-Speed data transfer.
¹ Includes the HD photo image format
² Includes support for the following graphics formats: TIFF, TIF, JPG, GIF, PNG, BMP, PCX, AND DCX
1-4
Media trays and supply capacity
Item
Dell 2330d
Dell 2330dn
Available input trays
Integrated 250-sheet tray
✔
✔
50-sheet MP feeder
✔
✔
1-sheet manual feed slot
x
x
250-sheet drawer
✔
✔
550-sheet drawer
✔
✔
Optional input sources
Maximum input sheet capacity
850
850
(excluding envelopes)
(excluding envelopes)
Integrated
Integrated
x
x
✔
✔
2,300 standard pages SWE¹
2,300 standard pages SWE¹
3,500 standard pages
3,500 standard pages
High toner cartridge
9,000 standard pages
9,000 standard pages
Photoconductor kit
Up to 30,000 ²
Up to 30,000 ²
Manual/integrated print duplex
Envelope conditioning
Available output trays
Standard 150-sheet sensing bin
Toner and photoconductor
Toner cartridge
¹ Declared value in accordance with ISO/IEC 19752
² Up to 30,000 pages, based on an average of 3 pages per job and approximately 5% coverage per page. Yields may
vary based on customer usage.
General information
1-5
Types of print media
Note: Ensure trays are properly loaded. Never mix media types within a tray.
Source
Input tray 1
(250-sheet tray)
2nd Drawer option
(250/550-sheet
drawer)
Multipurpose
feeder
Sizes
Types
A4, A5, A6,JIS¹-B5,
letter, legal, executive,
oficio (Mexico)², folio²,
statement
Plain paper,
recycled, labels,
bond, letterhead,
preprinted, colored
paper, light paper,
heavy paper,
rough/cotton,
custom type [x]
60-90 g/m²
A4, A5, JIS¹-B5, letter,
legal, executive, oficio
(Mexico)², folio²,
statement
Plain paper,
recycled, labels,
bond, letterhead,
preprinted, colored
paper, light paper,
heavy paper,
rough/cotton,
custom type [x]
60-90 g/m²
A4, A5, A6,JIS¹-B5,
letter, legal, executive,
oficio (Mexico)², folio²,
statement
Plain paper,
transparency,
recycled, labels,
bond, letterhead,
preprinted, colored
paper, light paper,
heavy paper,
rough/cotton,
custom type [x]
60-163 g/m²
Card stock***
Duplex
Weight
Input capacity* (sheets)
• 250 paper
• 50 labels**
(16-24 lb)
• 250 paper
• 550 paper
• 50 labels**
(16-24 lb)
• 50 paper
• 15 labels**
• 10 transparencies
(16-43 lb)
• 120-163 g/m²
(16-43 lb)
Index Bristol
• 75-163 g/m²
(46-100 lb)
Tag
7 ¾, 9, 10, DL, C5, B5,
other
Envelopes
Rough envelopes
75 g/m² (20 lb)
A4, letter, legal, oficio
(Mexico)², folio²
Plain paper,
recycled, bond,
letterhead,
preprinted, colored
paper, light paper,
heavy paper,
custom type [x]
60-90 g/m²
20
7
(16-24 lb)
* Capacity for 20 lb print media, unless otherwise noted.
** Use for occasional printing only.
*** Grain short is recommended. Use rear exit for best results.
¹Japanese Industry Standard
² If a source supports size sensing and is activated, then neither the “oficio” value nor the “folio” value appears in that
source’s list of supported media sizes. These values only appear in a source’s list of supported media sizes either when
the source is non-size sensing or when the source’s size sensing hardware is deactivated and then the device is power
cycled.
1-6
Tips on preventing jams
Paper path
I
J
F
E
G
B
C
H
D
K
L
M
A
A
B
C
D
E
F
G
H
I
J
K
L
M
Paper path
Manual feed sensor
Upper end feed rolls
Input sensor
Transfer roll
Fuser
Fuser exit rolls
Fuser exit sensor
Exit rolls
Exit sensor
Duplex unit
Duplex sensor
Auto compensator
A-B
B-C
C-D
D-E
E-F
F-G
G-H
H-I
I-J
I-K
K-L
L-M
125.3 mm
9.0 mm
59.8 mm
44.9 mm
112.7 mm
21.4 mm
114.8 mm
7.5 mm
17.0 mm
211.7 mm
93.4 mm
8.4 mm
General information
1-7
Most paper jams can be avoided by correctly loading paper and specialty media in the printer.
The following hints can help prevent paper jams:
• Use only the recommended print media.
• Do not overload the print media sources. Make sure the stack height does not exceed the maximum height
indicated by the stack line on the labels in the sources.
• Do not load wrinkled, creased, damp, or curled print media.
• Flex, fan, and straighten print media before loading it. If jams do occur with the print media, then try feeding
one sheet at a time through the manual feeder.
• Do not mix print media sizes, weights, or types in the same print media source.
• Push all trays in firmly after loading them.
Note: Make sure the media stack is below the maximum media fill indicators on the 250-sheet tray before
pushing the tray into the printer.
•
•
•
•
•
Make sure paper guides are positioned before loading the paper or specialty media.
Do not remove trays while a job is printing.
Before loading transparencies, fan the stack to prevent sheets from sticking together.
Do not use envelopes that:
– Have excessive curl
– Are stuck together
– Are damaged in any way
– Contain windows, holes, perforations, cutouts, or embossments
– Have metal clasps, string ties, or metal folding bars
– Have postage stamps attached
– Have any exposed adhesive when the flap is in the sealed position
Use only recommended media. Refer to the Card Stock & Label Guide available on the Dell Web site
at www.dell.com for more information about which media provides optimum results for the current
printing environment.
Tools
The removal and adjustment procedures require the following tools and equipment:
•
•
•
•
•
1-8
Spring hook
Needle nose pliers
Volt-ohmmeter
#1 and #2 Phillips screwdriver
Slotted screwdriver
Acronyms
ACM
ADC
ASIC
CBM
DEV
DIMM
ENA
FRU
HBP
HVPS
LCD
LED
LSU
LVPS
NVRAM
PC
PCL
POR
POST
PPDS
PRC
TAR
SDR
SWE
USB
V ac
V dc
Autocompensator Mechanism (or paper feed)
Analog-to-digital Converter
Application Specific Integrated Circuit
Complete Bill of Material
Development Roll (of print cartridge/photoconductor
system)
Dual In-Line Memory Module
External Network Adapter
Field Replaceable Unit
Host Based Printing
High Voltage Power Supply
Liquid Crystal Diode
Light Emitting Diode
Laser Scanning Unit
Low Voltage Power Supply
Nonvolatile Random Access Memory
Photoconductor
Printer Control Language
Power-On Reset
Power-On Self Test
Personal Printer Data Stream
People’s Republic of China
Toner Add Roll
Synchronous Dynamic RAM
Shipped With Equipment
Universal Serial Bus
Volts alternating current
Volts direct current
General information
1-9
1-10
2. Diagnostics information
Start
CAUTION: Unplug power from the printer before connecting or disconnecting any cable,
assembly, or electronic card. This is a precaution for personal safety and to prevent damage to the
printer.
This chapter contains the codes and diagnostic tools to aid in providing corrective action for a malfunctioning
printer. To determine the corrective action to repair a printer, look for the following information:
• A description of a problem, see “Symptom tables” on page 2-20.
• Information from the operator panel of the printer.
– Models 2330d and 2330dn have an operator panel with messages. See “Overview of the
operator panel and menus” on page 2-2.
Menus
Back
Stop
Power–On Self Test (POST) sequence
The following is an example of the events that occur during the POR sequence when the printer is turned on.
1. Diamonds are displayed on the operator panel.
2. While code is being loaded into DRAM, dots scroll across the operator panel.
3. A screen is displayed with the memory and processor speed. A typical example of this message is:
*
32 Mb
4.
5.
6.
7.
8.
9.
10.
400 Mhz
Performing Self Test is displayed.
Busy is displayed.
Close Door will be displayed if the cover is open.
Any cartridge errors, such as Defective Cartridge, are displayed.
Applicable maintenance messages are displayed.
Applicable toner low messages are displayed.
The printer displays Ready.
Diagnostics information
2-1
Overview of the operator panel and menus
Menu
button
LCD
display
Indicator
light
Menus
Back
Back
button
Stop
Left arrow
button
Select
button
Right arrow
button
Indicator light
The indicator light gives information about the status of the printer.
2-2
If the light is
The printer is
Off
Off
On
On, but idle
Blinking
On and busy
Stop
button
Buttons
Use the six operator panel buttons to open a menu, scroll through a list of values, change printer settings, and
respond to printer messages.
Note: Buttons act on the information displayed on the second line of the operator panel.
The use of the buttons and the layout of the display are described in the following table:
Button or control panel item
Function
Menus button
Press and release
to open the menus. The menus are available only when the
printer is in the Ready state.
Pressing
also returns the operator panel to the top level menu screen if pressed
while in a menu.
Back button
Press and release
Navigation buttons
to return to the previous screen.
Left arrow menu button
Right arrow menu button
Press and release
or
to scroll through menus, menu items, or printer options,
or to move between screens and menu options.
These buttons can also be used to automatically increase
desired number of copies.
or decrease
the
Select button
Press and release
to open a menu, to display the available values or
settings, or to save the displayed value as the new user default setting.
Note: When a new setting is saved as the default setting, it remains in effect until new
settings are saved or until factory defaults are restored. Settings chosen from a
software program can also change or override the user default settings selected from
the operator panel.
Stop button
•
•
•
•
Press
once to return to the previous display screen while in the menus.
Press
twice to exit the menus and return to the Ready state.
Press
to stop printer activity.
Press
to cancel a print job. Stopping will display momentarily. Stopped
will then display to offer a list of settings that may be selected.
Diagnostics information
2-3
Button or control panel item
Function
Display
The display shows messages describing the current state of the printer and indicating
possible printer problems that must be resolved.
The top line of the display is the header line. It will display the current status and the
Supplies (Warnings) status. This is where printer status, supplies messages, and
show-me screens are viewed.
Indicator light
The indicator light indicates printer status.
• If the light is off, then the printer power is off.
• If the light is blinking green, then the printer is warming up, processing date, or
printing.
• If the light is solid green, then the printer is on, but idle.
• If the light is blinking red, then operator panel intervention is needed.
2-4
Diagram of the printer menus
Not all menus or selections will be available on all models or in all situations. These are accessed through the
driver.
Paper Menu
Job Menu
Finishing Menu
Duplex
Duplex Bind
Copies
Blank Pages
Collation
Separator Sheets
Separator Source
Multipage Print
Multipage Order
Multipage View
Multipage Border
Utilities Menu
Quick Demo
Print Menus
Print Stats
Print Net Setup
Print Fonts
Print Demo
Factory Defaults
Hex Trace
Reset Printer
PostScript Menu
PCL Emul Menu
Setup Menu
Quality Menu
Print PS Error
Font Source
Font Name
Pitch
Symbol Set
Orientation
Lines per Page
A4 Width
Tray Renumber
Auto CR after LF
Auto LF after CR
Eco-Mode
Quiet Mode
Printer Language
Power Saver
Resource Save
Print Timeout
Wait Timeout
Auto Continue
Jam Recovery
Page Protect
Print area
Display Language
Toner Alarm
Print Resolution
Toner Darkness
Small Font Enh.
PPDS (if activated)
Parallel Menu
Network Menu
USB Menu
Orientation
Lines per Page
Lines per inch
Page Format
Character Se
Best Fit
Tray 1 Renumber
Auto CR after LF
Auto LF after CR
Std Parallel
Standard Network
Standard USB
Paper Source
Paper Size
Paper Type
Custom Types
Universal Setup
Substitute Size
Paper Texture
Paper Weight
Paper Loading
Diagnostics information
2-5
Messages and error codes
User attendance messages
The printer control panel displays messages describing the current state of the printer and indicates possible
printer problems that must be resolved. This topic provides a list of all printer messages, explains what they
mean, and tells how to clear the messages.
The following table lists the messages in alphanumerical order. A message can also be located using the index.
User attendance messages
Message
Action
Activating Demo Mode
Wait for the message to clear.
Activating Menu Changes
Wait for the message to clear.
Activating/Deactivating PPDS
Wait for the message to clear.
Busy
Wait for the message to clear, or cancel the print job.
Cancelling Job
Wait for the message to clear.
Change Cartridge Invalid Refill
The printer has detected an unsupported refilled cartridge. Remove the
indicated print cartridge, and install a new one.
Close door
Close the specified door to clear the message.
Deactivating Demo Mode
Wait for the message to clear.
Defragmenting Flash DO NOT POWER OFF
Warning: Do not turn the printer off while this message is displayed.
Wait for the message to clear.
Disabling Menus
Wait for the message to clear.
Note: The printer settings cannot be changed from the control panel while
the menus are disabled.
Enabling Menus
Wait for the message to clear.
Flushing Buffer
Wait for the message to clear.
Formatting Flash DO NOT POWER OFF
Warning: Do not turn the printer off while this message is displayed.
Wait for the message to clear.
Invalid Engine Code
Download valid engine code to the printer. POR while holding
if necessary to load code.
Invalid Standard Network Code
The code in an internal print server is not valid. The printer cannot receive
and process jobs until valid code is programmed into the internal print
server. Download valid code to the internal print server.
and
Note: The network code can be downloaded while this message is
displayed.
2-6
User attendance messages (Continued)
Message
Load manual feeder with <Custom Type>
Load manual feeder with <Custom
String>
Load manual feeder with <size>
Load manual feeder with <size> <type>
Load <src> with <Custom Type Name>
Load <src> with <Custom String>
Action
• Load the specified media in the manual feed tray or multipurpose
feeder.
• To ignore the manual feed request and print on media already
installed in one of the input sources, press .
If the printer finds a tray that has media with the correct media type
and size, then it feeds media from that tray. If the printer cannot find
a tray with the correct media type and size, then it prints on
whatever media is installed in the default input source.
• Cancel the current job.
• Load the input source with the correct type and size media.
• Cancel the current job.
Load <src> <size>
Load <src> <type> <size>
Maintenance
Replace the maintenance items and, if necessary, reset the printer
maintenance counter.
Menus Disabled
The printer menus are disabled. The printer settings cannot be changed
from the control panel.
Note: A job can still be canceled.
Contact a system support person.
Network
A network interface is the active communication link.
Network Card Busy
An internal print server (also called an internal network adapter or INA) is
being reset. Wait for the message to clear.
Not Ready
The printer is not ready to receive or process data. Someone pressed
to take the printer offline. Press
to make the printer ready to receive
jobs.
Parallel
A parallel interface is the active communication link.
Performing Self Test
The printer is running the series of start-up tests it performs after it is
turned on. Wait for the message to clear.
Power Saver
• Send a job to print.
• Press
to warm the printer to normal operating temperature and
display the Ready message.
Printing Directory List
The printer is processing or printing a directory of all files stored in flash
memory. Wait for the message to clear.
Printing Font List
The printer is processing or printing a list of all available fonts for the
specified printer language. Wait for the message to clear.
Printing Menu Settings
The printer is processing or printing the menu settings page. Wait for the
message to clear.
Printing Device Statistics
The printer is printing statistical information about the printer. Wait for the
message to clear.
Printing Quality Test Pages
The printer is formatting and printing the Print Quality Test, which consists
of 4 pages. Page 1 contains a mixture of graphics and text, pages 2 and 3
contain only graphics, and page 4 is a blank page. If Duplex is turned on,
then the pages are duplexed; otherwise they are simplexed. Wait for the
message to clear.
Diagnostics information
2-7
User attendance messages (Continued)
Message
Action
Prog Engine Code
DO NOT POWER OFF
The printer is is being programmed with a new engine code. Wait for the
message to clear and the printer to reset.
Warning: Do not turn the printer off while this message is displayed.
Program Flash
DO NOT POWER OFF
The printer is storing resources, such as fonts or macros, in flash memory.
Wait for the message to clear.
Warning: Do not turn the printer off while this message is displayed.
Prog System Code
DO NOT POWER OFF
The printer is programming new system code. Wait for the message to
clear and the printer to reset.
Warning: Do not turn the printer off while this message is displayed.
Ready
Send a job to print.
Remove Paper Standard Bin
The standard output bin is full.
Resetting Maint Cnt Valu
The printer is resetting the counter that tracks wear on the fuser.
Resetting PC Cnt Value
The printer is resetting the counter that tracks wear on the photoconductor.
Resetting the Printer
Wait for the message to clear.
Res Reduced
The printer is reducing the resolution of a page in the current job from 600
dots per inch (dpi) to 300 dpi to prevent a 38 Memory Full error. Res
Reduced remains on the display while the job prints.
Restoring Factory Defaults
Wait for the message to clear.
Note: When factory default settings are restored:
• All downloaded resources (fonts, macros, symbol sets) in the
printer memory are deleted.
• All menu settings return to the factory default except:
– The Display Language setting in the Setup Menu
– All settings in the Parallel Menu, Network Menu, and
USB Menu
Std Bin Full
Toner Low
The standard bin is full.
• Replace the toner cartridge.
• Press
to clear the message and continue printing.
Tray <x> Missing
Insert the tray into the printer.
USM
The printer is processing data through the specified USB port.
Waiting
The printer has received a page of data to print, but is waiting for an End of
Job command, a Form Feed command, or additional data.
• Press
to print the contents of the buffer.
• Cancel the current job.
2-8
Cartridge error messages
Error
Description
30
Invalid refill
31
Missing or defective cartridge
32
Unsupported print cartridge
Action
Replace the cartridge.
Paper jam error codes (200-series)
Note: The Event log (See “Event log” on page 3-14) will list any of these errors that have occurred.
Repeating jams or jam messages can be caused by any of the following:
•
•
•
•
Error
Faulty/contaminated pick solenoids or worn cams of the solenoids.
Faulty/contaminated flags or springs.
Debris in the paper path.
Media not of the specified length.
Description
Action
200.00
Paper jam around input sensor.
Remove the PC kit and paper or debris at the input
sensor.
200.01
Classic input jam. The media is too long over the input
sensor. Possible causes include multi-sheet feed, tray
size sensing problem, and media slippage.
200.02
The main input sensor never became uncovered from
the sheet ahead.
First, remove the PC kit and paper or debric at the
input sensor. Then, inspect the flag on the input
sensor. It should rotate freely. Replace the sensor if
necessary. Finally, check the paper size settings in
the printer and the driver.
200.03
The video never started on the page at the input
sensor within two inches after hitting the input sensor
Check the printhead. See “Printhead service
check” on page 2-37.
200.04
The media at the input sensor before interrupt
occurred–not enough time elapsed since the printhead
started to expect the printhead mirror motor lock.
Possible causes include bouncy sensor or
exceptionally fast pick– perhaps due to media prestaged in the source tray.
Carefully remove the tray and notice if the leading
edge of the media is pointed upward and out of the
tray. If so, then inspect the tray wear strips and
replace if necessary.
200.06
Imaged page not expected page (bouncy passthru
sensor)
Remove the toner cartridge/PC kit. At the front,
remove the upper front guide, and inspect the flag on
the manual input sensor. If the flag is loose, then
replace it. See “Media manual input sensor
removal” on page 4-39.
200.08
Media reached the input sensor before the EP was
ready
Inspect the tray for prestaging. Verify the proper
media and inspect the tray wear strips. Replace the
wear strips if necessary.
200.09
Transfer servo never started
Inspect the LVPS/HVPS. See “Controller board
service check” on page 2-22.
200.12
Media detected at manual feeder sensor when not
expected. Possible causes include user insert of media
when motor is running or pre-staged media in the tray.
Carefully remove the tray and notice if the leading
edge of the media is pointed upward and out of the
tray. If so, then inspect the tray wear strips and
replace if necessary.
Inspect the input sensor flag and replace it if it does
not rotate freely or is too loose.
Inspect the input sensor flag and replace it if it does
not rotate freely or is too loose.
Diagnostics information
2-9
Error
Description
Action
200.13
The input sensor is covered when the media is not
expected (media in machine during warm-up)
Remove the toner cartridge/PC kit and inspect the
input sensor flag. Replace the flag if necessary.
200.14
Trailing edge cleared manual feed, but did not
successfully debounce the sensor. Potential causes
are a small gap or a bouncy manual feed sensor.
Remove the toner cartridge/PC kit. At the front,
remove the upper front guide, and inspect the flag on
the manual input sensor. If the flag is loose, then
replace it. See “Media manual input sensor
removal” on page 4-39.
200.15
UNRECOVERABLE NO GAP JAM. Engine detected
no gap at the manual feeder sensor, attempted to
open the gap by stopping the feed rolls, but no trailing
edge was ever seen at the input sensor.
Remove the toner cartridge/PC kit. At the front,
remove the upper front guide, and inspect the flag on
the manual input sensor. If the flag is loose, then
replace it. See “Media manual input sensor
removal” on page 4-39.
Verify that the media is approved. Inspect the wear
strips in the input tray, and replace if necessary.
200.16
Transport motor error detected
200.17
Took too long to ramp up transport motor
200.18
Manual feeder sensor never became uncovered from
the sheet ahead.
Remove the toner cartridge/PC kit. At the front,
remove the upper front guide, and inspect the flag on
the manual input sensor. If the flag is loose, then
replace it. See “Media manual input sensor
removal” on page 4-39.
200.19
The media never reached the input sensor, but was
detected at manual feeder sensor.
Remove the toner cartridge/PC kit, and inspect for
debris in the paper path. Check the bottom of the PC
kit for any obstructions. Remove the upper front
guide, and inspect the pinch rollers.
200.20
The media is too long over the manual feeder sensor.
Possible causes include multi-sheet feed, media size
(length) problem, pre-staged media in the tray.
Verify that the media is approved. Inspect the wear
strips in the tray, and replace if they are worn.
200.22
FAILED SMALL GAP OR NO GAP JAM RECOVERY.
Engine detected small gap or no gap at the manual
feeder sensor, opened the gap by stopping the feed
rolls, but never saw the leading edge of the second
page at the input sensor.
200.23
Laser Servo never started due to potential conflict with
the transfer servo. Possible causes: slow or missing
transport motor positional feedback, or the media is
transferred too quickly to the input sensor.
Verify that the media is approved. Inspect the wear
strips in the tray, and replace if they are worn.
200.24
The measured gap at the input sensor is too small to
meet the video delivery requirements. (There is not
enough time since prior image finished to start new
image)
Verify that the media is approved. Inspect the wear
strips in the tray, and replace if they are worn.
200.26
The trailing edge never cleared the input sensor when
feeding out the media that was detected during warmup.
200.27
Printhead Driver: Mirror motor fell out of lock condition
after the media at the input sensor–more time elapsed
since the printhead than the expected stable lock time,
but less than the printhead jitter-stable specification.
Mirror motor fell out of lock condition after media at the
input sensor–more time elapsed since the printhead
than expected stable lock time, but less than the
printhead jitter-stable specification.
2-10
Inspect the main motor. See “Main motor service
check” on page 2-26.
Check the main motor. See “Main motor service
check” on page 2-26.
Check the printhead. See “Printhead service
check” on page 2-37.
Error
Description
Action
200.28
First writing line of a page at the developer nip, but
laser servo cleanup is not complete. Likely pre staged
media or a fast paper feed.
Verify that the media is approved. Inspect the wear
strips in the tray, and replace if they are worn.
200.29
Printhead drive control out of range due to an external
event beyond what the control is designed to handle.
Probable causes: ESD or noise on hsync signal.
Check the cable routing for the printhead. See
“Printhead service check” on page 2-37.
200.30
Narrow media sensor covered during warm-up.
Check that the narrow media flag rotates freely and
securely. If it is dislodged or broken, then repalce the
rear exit guide. See “Rear exit guide assembly
with sensor and reversing solenoid removal” on
page 4-48.
200.32
Media more than 14 inches too long over the manual
feeder sensor. Possible causes include multi-sheet
feed or pre-staged media in the tray.
Verify that the media is approved. Inspect the wear
strips in the tray, and replace if they are worn.
200.33
Page from tray 1 did not reach the input sensor after
multiple attempts. Page did make it out of the tray at
least as far as the manual feeder sensor. Possible
cause is that the page stalled at the alignment gate.
Verify that the pick tires are clean, not worn, or filled
with paper dust. Replace the pick tires if necessary.
See “ACM pick tire roller removal” on page 4-3.
200.34
Timed out waiting for page from tray 1 to reach the
input sensor after multiple pick attempts, but the page
was later detected at the input sensor while waiting for
any page(s) ahead to clear the paper path. Possible
cause is that the page is delayed at the alignment
gate.
200.35
Failed to create hsync during auto alignment
200.36
Lost hsyncs during auto alignment
200.37
Timeout on data collection during auto alignment
200.38
Interpage servo gap is smaller than expected for
printhead offset target evaluation
200.42
Rogue sheet is at the manual feed sensor while
flushing the paper path prior to declaring MPF source
empty.
Retry alignment.
200.43
The media is at the input sensor before interruption
occurs. Possible causes include bouncy sensor or an
exceptionally small gap, perhaps due to the media
being pre-staged in the source tray.
Remove the media, realign the stock, and re-insert.
Do not let the top sheets to go beyond the wear
strips.
201.00
Paper jam between input and exit sensor
Remove the toner cartridge/PC kit and check for
obstructions between the input sensor and the fuser.
if the media continues to stop at the entrance or in
the fuser, then replace the fuser. See “Fuser
removal” on page 4-20.
201.01
Transport motor identification failed to identify either
motor after two tries.
Check the main motor. See “Main motor service
check” on page 2-26.
201.02
Exit sensor never made by leading edge of page. Also
known as internal jam.
Remove the PC kit and paper or debris at the input
sensor.
201.03
Video never started on the page at the input sensor
within two inches after hitting the input sensor
Check the printhead. See “Printhead service
check” on page 2-37.
201.05
Restart attempted after an internal jam without the
cover open/close event. It is likely that the jam was
never cleared.
Check the paper path and remove any media in the
path.
The alignment roller may be binding. Call the next
level of support.
Check the printhead. See “Printhead service
check” on page 2-37.
Diagnostics information
2-11
Error
Description
201.25
Exit sensor never made by leading edge of media
when feeding out the media that was detected during
warm-up.
201.26
Page at fuser nip before fuser started ramping toward
desired temperature. Indicates code may be receiving
more interrupts than intended
201.27
Page at fuser nip before fuser reached acceptable
operating temperature. Page arrived at fuser earlier
than expected, so it was probably staged prematurely.
202.00
Paper jam around exit sensor.
Action
Remove the toner cartridge/PC kit and check for
obstructions between the input sensor and the fuser.
if the media continues to stop at the entrance or in
the fuser, then replace the fuser. See “Fuser
removal” on page 4-20.
Open the rear cover and look for obstructions in the
path way. If there are none, then inspect for damage
at the fuser, rear door, exit guide, and top cover.
Often, the leading edge of the media will indicate the
vacinity of damage. If damage is found, then replace
the damaged part.
Note: Print a page with the rear door open to isolate
the fuser from the other parts.
202.01
Exit sensor never broke on the trailing edge of the
sheet at the exit sensor.
202.02
Exit sensor never broke from sheet ahead of page
heading toward the exit sensor.
202.06
Exit sensor bounced
202.13
Exit sensor covered, media not expected (media not in
machine during warm-up)
202.25
Exit sensor never broke from the sheet ahead of the
page heading toward the exit sensor when feeding out
the media detected during warm-up.
202.26
Trailing edge never cleared exit sensor when feeding
out media that was detected during warm-up.
Open the rear door, and inspect the flag on the exit
sensor. The flag is located behind the fuser exit
rollers, about mid printer. If the flag does not rotate
freely or has no spring action, then replace the fuser.
See “Fuser removal” on page 4-20.
202.32
Long media or shingled multi feed stopped before
sending to duplex.
Check the paper setting and correct if needed. While
feeding along the media, and immediately after it
enters the output bin, open the reat door and
obscure the trailing edge and the sensor flag. If there
is slippage in the exit guide, then replace the exit
guide. See “Rear exit guide assembly with sensor
and reversing solenoid removal” on page 4-48.
2-12
Open the rear door, and inspect the flag on the exit
sensor. The flag is located behind the fuser exit
rollers, about mid printer. If the flag does not rotate
freely or has no spring action, then replace the fuser.
See “Fuser removal” on page 4-20.
Error
Description
Action
231.00
Duplex jam while reversing into the device
Open the rear cover and look for obstructions
between the rear cover ribs, the fuser exit rollers,
and below. The media entering the duplex passes
outside the exit roller while the media exiting the
fuser passes above and inside the exit rollers.
Remove the tray, open the duplex door, and remove
the obstructions. If there are no obstructions and the
problem persists, then disconnect all of the cables,
tilt the printer onto its back (be sure to protect the
antenna on a wireless unit), and inspect the flag of
the duplex sensor. If the flag does not rotate freely,
then replace the paper input and duplex sensor. See
“Paper input and duplex sensor assembly
removal” on page 4-44.
231.01
Duplex sensor never made by leading edge reversing
into the duplex.
231.02
Bouncy duplex sensor never made.
232.00
Duplex jam while staging in the device
232.01
Duplex sensor never broke by the sheet ahead after
reversing into the duplex.
232.02
Page in duplex ahead of current reversing page never
staged.
233.00
Duplex jam while picking from the device
233.01
Page in duplex never picked.
233.02
Feed error picking from the duplex.
233.03
Paper never reached the input sensor, but was
detected at the manual feed sensor.
234.01
Duplex sensor covered during warm-up.
235.01
Invalid duplex media
Check the media. Duplex supports A4, letter, legal,
oficio, and folio media sizes.
241.00
Paper jam near tray 1.
241.10
Second pick attempt failed from Tray 1
Remove the tray and inspect the media path for
obstructions. Check the pick rollers. Replace the pick
rollers if they are worn or clogged with dust. See
“ACM pick tire roller removal” on page 4-3. Also
check the wear strips, and replace if necessary.
241.12
Second pick from manual feeder, tray 1, or feeder
failed when the media was in the source while other
sheets were committed to the paper path.
241.16
Failed to feed from tray 1. Pages in the paper path
have been flushed to the output bin.
241.17
MISIDENTIFIED SMALL GAP JAM. Engine detected
small gap at the manual feeder sensor, attempted to
open the gap by stopping the feed rolls, trailing edge
was seen at the input sensor, manual feeder sensor is
no longer covered.
241.19
Second pick attempted failed from Tray 1, no pages
printed since calling a 241.10 or a prior 241.19.
242.00
Paper jam near tray 2.
Remove Tray 2 and inspect for obstruction in the
paper path. Check the pick tires for wear or paper
dust. Replace if necessary. Check the wear strips
and replace if necessary.
242.01
Took too long to ramp up dc feed motor
242.08
Received lots of dc feed interrupts before losing them
Check the connection with Tray 2. (Lift the printer
and re-set it on Tray 2.) If the error persists, then
replace Tray 2.
242.10
Second pick attempt failed from Tray 2
Check the belt and drive of the duplex unit. Replace
it if necessary.
Remove the tray and inspect the media path for
obstructions. Check the pick rollers. Replace the pick
rollers if they are worn or clogged with dust. See
“ACM pick tire roller removal” on page 4-3. Also
check the wear strips and the manual feeder, and
replace if necessary.
Remove Tray 2 and inspect for obstruction in the
paper path. Check the pick tires for wear or paper
dust. Replace if necessary. Check the wear strips
and replace if necessary.
Diagnostics information
2-13
Error
Description
Action
242.12
Second pick from manual feeder, tray 1, or feeder
failed when media was in the source, other sheets
were committed to the paper path.
Check the wear strips and replace them if worn.
242.16
Failed to feed from tray 2. Pages in the paper path
have been flushed to the output bin.
Remove Tray 2 and inspect for obstruction in the
paper path. Check the pick tires for wear or paper
dust. Replace if necessary. Check the wear strips
and replace if necessary.
251.00
Paper jam near the manual feeder.
251.10
Second pick attempt failed from manual feeder.
Inspect the pick roller on the MPF or the rollers on
the manual feed. If the MPF pick roller is damaged or
worn, then replace the MPF. For a printer with a
manual feed only (no MPF), clean the roller.
251.11
Failed to feed from manual feeder. Pages in the paper
path have been flushed to the output bin.
251.12
Second pick from manual feeder, tray 1, or feeder
failed when media was in the source while the other
sheets were committed to the paper path.
251.19
Media never reached the input sensor from the manual
feeder.
251.20
The media in the MPF has been pushed in too far.
251.21
The media in the MPF has been pushed in too far.
2-14
Remove the media, realign the stock, and re-insert.
Do not let the top sheets to go beyond the wear
strips.
Service error codes
Service error codes are generally non-recoverable except in an intermittent condition when the printer can be
put into POR to temporarily recover from the error condition.
Error
Description
Action
Engine software service errors
902.xx
Engine software error
Replace the controller board. See “Controller
board service check” on page 2-22
DC pick motor errors
914.00
DC pick motor error
914.01
Lost encoder feedback
Transfer service errors
917.xx
Transfer service error
Replace the transfer roll. See “Transfer roll
service check” on page 2-37.
Fuser service errors
920.00
Under temperature during steady state control.
920.01
Fuser took too long to heat up after transitioning to new
enhanced mode.
920.02
Fuser fell too far below desired temperature while
printing.
920.03
Fuser too cool while checking for slope change.
920.04
Fuser too cool when heating to desired temperature
after slope change.
920.05
Fuser under temperature while printing
920.06
Fuser under temperature while printing
920.07
Fuser under temperature while printing
920.08
Fuser temperature did not increase after IR recovery.
920.20
Belt fuser under temperature during steady state control.
This can occur in printing or standby modes.
921.00
Under temperature during standby control.
921.01
Fuser temperature did not reach standby temperature
after two attempts
922.00
Fuser failed to ramp to target temperature
922.01
Fuser did not reach standby temperature in time
(standby control)
922.02
Hot roll took too long to reach the beginning lamp
detection temperature.
922.03
Hot roll reached final lamp detection temperature, but
took longer than largest time in lookup table.
922.04
Hot roll timed out in trying to reach the final lamp
detection temperature.
Replace the fuser. See “Fuser service check”
on page 2-25.
Diagnostics information
2-15
Error
Description
922.05
Did not roll over to a steady state control in time after the
hot roll lamp detection.
922.06
Hot roll did not reach the operating temperature in time
(new enhanced control).
922.07
Media reached fuser nip, and fuser is under temperature
922.08
Fuser warm-up failure (motor start condition)
922.09
Fuser warm-up failure (compression set)
922.20
Belt fuser failed to reach the preheat temperature for the
motor to start during warm-up.
922.21
Belt fuser was under temperature when the media
reached the fuser nip.
923.00
Fuser is over temperature.
923.01
Fuser is over temperature. This applies to the fuser and
belt fusers.
924.00
Open thermistor check.
924.01
Open thermistor check failure. This applies to the fuser
and belt fusers.
924.02
Open thermistor check failure. The ADC failed to
converge. Possible noisy thermistor signal. This applies
to the fuser and belt fusers.
925.xx
Wrong fuser installed. The fuser type stored in the
cartridge ID does not match the actual fuser installed in
the printer.
Action
Replace the fuser. See “Fuser service check”
on page 2-25.
Fan service errors
927.00
Service fan error
927.03
Main fan took too long to ramp up
927.04
Main fan is under speed or stalled during speed
adjustment state
927.05
Main fan overspeed during speed adjustment state.
927.06
Main fan capture data is invalid, and speed control is at
maximum in fan control idle state
927.07
Main fan capture data is invalid, and speed control is at
maximum in fan control adjustment state.
Replace the fan. See “Cooling fan service
check” on page 2-23.
Toner service errors
929.00
Toner sensor error
929.01
No home window
929.02
No sensor transition (closed)
929.03
No sensor transition (open)
Remove the toner cartridge, and shake it Try a
different toner cartridge, if possible. If the error
persists, then replace the toner level sensor. See
“Toner level sensor removal” on page 4-60.
Printhead service errors
930.00
Wrong printhead installed
931.00
No first hsync
2-16
Replace the printhead. See “Printhead service
check” on page 2-37.
Error
Description
931.01
No first hsync
932.00
Lost hsyncs
932.01
Lost hsyncs
933.01
Printhead boost signal failure
934.00
Mirror motor lost lock.
934.01
Mirror motor lost lock.
935.00
No initial mirror motor lock
935.01
Timed out waiting for mirror motor lock
935.10
Printhead sweep error, swept through Hz range without
finding the resonant frequency
935.12
Printhead sweep error, coarse sweep state
935.15
Printhead open-loop error, check prelim amp state
935.16
Printhead open-loop error, enable amp Kp state
935.17
Printhead closed-loop error, amp Kp failed to converge
935.18
Printhead closed-loop error, enable amp Ki state
935.19
Printhead closed-loop error, amp Ki failed to converge
935.20
Printhead closed-loop error, enable offset controller
state
935.21
Printhead closed-loop error, load scan regs state
935.22
Printhead closed-loop error, fwd and rev capture times
differ by too much
935.23
Printhead closed-loop error, check sweep accuracy
state
935.25
Printhead closed-loop error, off-resonant PI effort state
935.26
Timed out on POR sweep
935.27
Exceeded maximum open loop drive level when
configuring for sweep re-try.
935.28
Exceeded maximum open loop drive level when setting
operating Hz.
Action
Replace the printhead. See “Printhead service
check” on page 2-37.
Transport motor service errors
936.01
No lock detected at normal motor start
936.02
No lock detected at motor start for motor ID
936.03
No halls detected at motor start
936.04
Failed to stop within timeout
936.05
Stall detected during speed control
Replace the main motor gear drive. See “Main
motor service check” on page 2-26
Diagnostics information
2-17
Error
Description
937.00
Main transport motor lost lock
937.01
Main transport motor lost lock, detected by engine
control
937.02
Overspeed detected during position control
937.03
Overspeed detected during speed control
Action
Replace the main motor gear drive. See “Main
motor service check” on page 2-26
Power supply service errors
940.00
LVPS service error
940.01
Line frequency outside allowed range of 45Hz-64Hz
940.02
Line frequency below 43Hz
940.03
No zero cross detected on belt fuser model
Replace the LVPS/HVPS. See “LVPS/HVPS
service check” on page 2-25.
Controller board and operator panel service errors
948.xx
Failed engine board
Replace the controller board. See “Controller
board service check” on page 2-22.
Mismatch between EEPROM and mirror memory
Install a new controller bored or operator panel.
See “Controller board service check” on
page 2-22 or “Operator panel service check”
on page 2-27.
949.xx
950.xx
Note: A new controller board or operator panel has been
installed, and has not been properly prepared for this
use. Install a new note. Do not install both the controller
board and the operator panel at the same time without a
POR in between.
951.xx
Error with secure NVRAM on the controller board
Replace the controller board. See “Controller
board service check” on page 2-22.
952.xx
A recoverable MVRAM Cyclic Redundancy Check error
occurred.
Performing POR will clear this error.
953.xx
NVRAM chip failure with mirror
Replace the operator panel. See “Operator
panel service check” on page 2-27.
954.xx
NVRAM chip failure with system part.
955.xx
The code ROM or NAND flash failed the Cyclic
Redundancy Check or the NAND experienced an
uncorrectible multi-bit failure.
Replace the controller board. See “Controller
board service check” on page 2-22.
956.00
RIP card failure: processor failure
956.01
Processor overtemp
957.xx
RIP card failure: ASIC failure
958.xx
Printer has performed more than 100 “shift and reflash”
operations as a result of ECC bit corrections
Firmware or controller board errors
959.01
Controller verification failure of pensive boot code
959.02
Failure to authenticate Signature Verification Code
2-18
Call the next level of support to update the
firmware, or replace the controller board. See
“Controller board service check” on
page 2-22.
Error
Description
Action
959.03
Signature Verification Code failed to authenticate a code
partition.
Update firmware and call the next level of
support, or replace the controller board. See
“Controller board service check” on
page 2-22.
959.04
Jump to unverified address
959.05
Unknown boot failure
Update firmware and call the next level of
support, or replace the controller board. See
“Controller board service check” on
page 2-22
959.20
Pensive hardware failure
959.21
Pensive did not respond to command request.
Replace the controller board. See “Controller
board service check” on page 2-22.
959.22
Challenge secret failure
959.23
Pensive self test failed during initialization.
959.24
EEPROM retention error
959.25
Insufficient device space during HW prog
959.26
Incremental counter reset exceeds maximum value
959.27
Increment count failed due to max value limit
959.28
Invalid SP memory configuration
Replace the controller board. See “Controller
board service check” on page 2-22.
Memory and emulation errors
960.xx
RAM memory error: RAM soldered on the controller
board is bad
Replace the controller board. See “Controller
board service check” on page 2-22.
961.xx
RAM memory error: memory card in slot is bad.
Replace the memory card.
964.xx
Download Emulation Cyclic Redundancy Check Error:
checksum failure detected in the emulation header or
emulation file.
Disable the Download Emulation. Program the
download emulation into the firmware card again.
If this does not resolve the problem, then replace
the firmware card and download the emulation
again.
Network errors
975.xx
Unrecognizable network
976.xx
Unrecoverable software error in network port
978.xx
Bad checksum while programming network port
979.xx
Flash parts failed while programing network port
Call the next level of support.
Other errors
980.xx
Engine experiencing unreliable communication with the
specified device
981.xx
Engine protocol violation detected by the specified
device
982.xx
Communications error detected by the specified device
983.xx
Invalid command received by the specified device
Call the next level of support.
Diagnostics information
2-19
Error
Description
Action
984.xx
Invalid command parameter received by the specidied
device
990.xx
An equipment check condition has occurred in the
specified device, but the device is unable to identify the
exact component failure.
991.xx
The specified device has detected an equipment check
in its system card.
Call the next level of support.
Symptom tables
POST symptom table
Symptom
Action
The main motor, cooling fan, and fuser do not come
on.
See “Cover interlock switch service check” on page 2-23.
POST completes, but the LCD does not come on.
See “Operator panel service check” on page 2-27.
Main motor does not come on.
See “Main motor service check” on page 2-26.
Fan does not come on.
See “Cooling fan service check” on page 2-23.
Fuser does not cycle.
See “Fuser service check” on page 2-25.
Fuser does not turn on and off.
See “Fuser service check” on page 2-25.
The paper feed picks and tries to feed media.
See “Paper feed service checks” on page 2-27.
Note: Investigate any displayed codes before proceeding with these symptoms. For example, a missing toner cartridge will
prevent POST from completing.
2-20
Printer symptom table
Symptom
Action
Fan noisy or fan not working.
See “Cooling fan service check” on page 2-23.
Fuser parts melted.
See “LVPS/HVPS service check” on page 2-25.
Toner not fused to the media.
See“Fuser service check” on page 2-25 or “Solving print
quality problems” on page 2-34.
Paper jams.
See “Paper feed service checks” on page 2-27.
Main motor noisy or not moving.
See “Main motor service check” on page 2-26.
Media skew.
See “Paper feed service checks” on page 2-27.
Printer not communicating with host.
See “Parallel or USB port service check” on page 2-29.
Front access door will not close.
See “Cover interlock switch service check” on page 2-23.
Operator panel button not responding.
See “Operator panel service check” on page 2-27.
Operator panel lights are off or very dim.
See “Operator panel service check” on page 2-27.
Blank page.
See “Blank page” on page 2-30.
Black page.
See “Black page” on page 2-31.
Heavy background.
See “Heavy background” on page 2-31.
Light print.
See “Light print” on page 2-33.
White or black lines or bands.
See “White or black lines or bands” on page 2-33.
Toner on back of page.
See “Toner on back of page” on page 2-33.
Media never picks.
See “Media never picks” on page 2-28.
Media feeds continuously.
See “Media occasionally mispicks or picks multiple sheets
at once” on page 2-28.
Media wrinkled or bent.
See “Media “trees,” wrinkles, stacks poorly, or curls” on
page 2-29.
Dead machine (no power).
See “Dead machine service check” on page 2-24.
Print quality problems
See “Solving print quality problems” on page 2-34.
•
•
•
•
•
•
Light print
Blurred characters
Toner on both sides of media
Toner not fused
Streaks
Blank pages
Diagnostics information
2-21
Service checks
Service checks which involve measuring voltages on the LVPS/HVPS (low voltage power supply/
high voltage power supply board) should be performed with the printer positioned on its back side.
Note: When making voltage readings, always use frame ground unless another ground is
specified. See the wiring diagram in the back of the book for more information.
Controller board service check
Controller board service check
FRU
Action
Controller board
assembly
POST (Power-On Self Test)
Warning: Do not
replace the operator
panel and controller
board at the same
time. Each card
contains the printer
settings. When either
of these cards is new,
it obtains some of the
settings from the other
card. Settings are lost
when both are new
and replaced at the
same time.
Note: The printer should complete POST in approximately 30 seconds.
If the printer fails to display lights or activate the drive motor, fuser, or fan, then check the
following in order:
1. Power to the LVPS/HVPS
Turn the printer on and listen carefully for a click near the switch. A clicking sound
verifies that the outlet and power cables are good. Absence of a clicking sound may
indicate a lack of power supplied to the LVPS/HVPS.
2. Power from the LVPS/HVPS to the controller board
With the power on, check the LED below the right lower corner of the fan. If the LED
lights up, it indicates that power is supplied to the controller board. If the LED does not
light up, proceed to the next check item.
3. Cables correctly plugged, especially for the operator panel
The printer will not power-up without a functioning operator panel even with a lighted
LED on the controller board.
4. The controller board assembly
The LED adjacent to J12 will be illuminated if the card is powered and good.
5. The operator panel
See “Operator panel service check” on page 2-27.
Verify +24 V dc input from the LVPS/HVPS.
1. Turn the printer off.
2. Disconnect the LVPS/HVPS cable from the controller board at J502.
3. Turn the printer on.
4. Verify +24 V dc on positions 6, 17, and 19 of the cable connector (LVPS/HVPS). If there
is no voltage supplied on any of these positions, turn the printer off and go to step 7.
5. Verify +5 V dc on positions 1, 3, 4, 5, 11, 13 and 15 of the cable connector (LVPS/
HVPS). If there is no voltage supplied on any of these positions, turn the printer off and
go to step 7.
6. Turn the printer off. Check the continuity of the conductors of the cable and the card
connector with respect to ground. Verify that pins 10, 12, 14, 16 and 18 on the cable are
grounded. Verify the same pins on the card connector side are grounded too. If there is
no continuity on any of the card pins, verify that all the mounting screws are tight. If
there is still no connection to ground then replace the controller board. See “Controller
board removal” on page 3-6.
7. Open the LVPS/HVPS and disconnect the controller board-to-LVPS/HVPS cable at
CN201.Verify continuity in each conductor of the cable. This cable is not a replaceable
part. If continuity is still not good then go to “Dead machine service check” on
page 3-24.
Controller board voltage outputs
Turn the printer off, and plug the LVPS/HVPS cable into J502 of the controller board. See
the wiring diagram at the end of the manual which identifies the output voltages and
grounds for a good controller board.
Turn the printer off before plugging or unplugging any connectors.
2-22
Controller board service check (Continued)
FRU
Action
LVPS/HVPS
Verify main power to controller board
With the printer off, unplug the LPS/HVPS cable at J502 on the controller board. Verify
grounds on pins 10, 12, 14, 16 and 18 for both the cable and the controller board. If any of
these grounds are incorrect, then check the cable for continuity. If the cable fails continuity,
then call the next level of support.
Turn the printer on with the cable still unplugged, and verify the following on the cable
(controller board will not be powered):
Pins
Voltage
6, 17, 19
+24 V dc
1, 3-5, 11, 13,
15
+5 V dc
If any of the voltages are incorrect, then replace the LVPS/HVPS. See “Dead machine
service check” on page 2-24.
Cooling fan service check
FRU
Action
Cooling fan
Make sure the fan cable plug is properly seated at J9 (controller board).
Turn the printer on. Within a few seconds, the controller board assembly should apply
+24 V dc to pin 2.
• If voltage is not present, then check or replace the controller board. See “Controller
board removal” on page 4-6.
• If voltage is present, then check pin 1 for 24 V dc as well. If it is close to 24 V dc while
the fan is still idle, then replace the fan. See “Fan removal” on page 4-16.
Cover interlock switch service check
Note: Make sure a print cartridge assembly is installed and the cover closes all the way, engaging the cover
open switch lever.
FRU
Action
Cover interlock switch
Disconnect the cover interlock cable from the controller board at J7.
With the printer turned off:
1. Verify continuity between cable pin 1 and pin 2 with the door closed and discontinuity
with the door open.
2. Verify continuity between cable pin 1 and pin 3 with the door open and discontinuity with
the door closed.
3. Verify discontinuity between cable pins 2 and 3 whether the door is open or closed.
• If any fail, then replace the cover interlock switch.
• If both pass continuity, then turn the printer on, and measure +5 V dc on pin 2 at J7 on
the controller board.
• Verify pin 3 at J7 is ground.
• If voltage or ground is not present, then see “Controller board service check” on
page 2-22 for more information.
Diagnostics information
2-23
Dead machine service check
CAUTION: Check the AC line voltage. The voltage should be within the following limits:
• 100 V ac (volts alternating current)-127 V ac for the 110 V printer
• 200 V ac-240 V ac for the 220 V printer
FRU
Action
Unplug the printer. Remove the LVPS/HVPS, and check the fuses for continuity.
LVPS/HVPS
• If open, then replace the LVPS/HVPS.
• If not open, then check the switch continuity across its conductors with the switch on.
Turn the switch off. Plug the AC line into the LVPS/HVPS and switch unit on.
Note: Voltages are exposed at several places on the board. Do these verifications, and
then unplug the AC cord from the power supply:
Pins
Voltage
CN201-6, 17,
19
+24 V dc
CN201-10, 12,
14, 16, 18
Ground
CN201-1,3, 5,
11,13, 15
+5 V dc
• If voltages are not correct, then replace the LVPS/HVPS.
• If voltages are correct, then check the controller board. See “Controller board service
check” on page 2-22.
2-24
Fuser service check
When toner is partially fused to the media, it is usually caused by low fuser temperature.
The line voltage to the printer must be within the following limits:
• 100 V ac-127 V ac for the 110 V model printer
• 200 V ac-240 V ac for the 220 V model printer
This printer uses a belt fuser and therefore does not have a lamp.
Fuser service check
FRU
Action
Unplug the printer, and disconnect the fuser cable plug from the LVPS/HVPS board
connector at CN102.
Check for continuity across the fuser by checking across the connector pins.
Fuser power cable
LVPS/HVPS
Fuser
• If there is continuity, then check the LVPS/HVPS. See “LVPS/HVPS service check”
on page 2-25.
• If there is no continuity, then disconnect the fuser power cable at both ends and check
each conductor for continuity. Replace cable if necessary.
• If the cable tests good, then replace the fuser.
Reconnect the cables, turn the printer on, and at &12, check for approximately +5 V dc on
pin 1 and ground on pin 2. If line voltage is incorrect on pin 1, then see “Controller board
service check” on page 2-22 for more information.
Disconnect the thermistor cable from J12 on the controller board.
Measure the resistance across the ends of the thermistor cable.
Replace the fuser assembly if the resistance is lower than 1K ohm or shorted.
Note: Resistance measures approximately 400K ohms when cool and 1K ohms hot.
Fuser
LVPS/HVPS service check
FRU
Action
LVPS portion of board
Fuses that open typically indicate a faulty LVPS/HVPS.
LVPS/HVPS
Disconnect the power cable, and open the LVPS/HVPS enough to test the switch. The
switch will show continuity across the conductors with a meter when the switch is on. If the
switch is good, then see “Dead machine service check” on page 2-24 for more
diagnostics.
HVPS portion of board
Problems with the HVPS are exhibited in the print quality. See “Print quality service
checks” on page 2-30 for more information.
Diagnostics information
2-25
Main motor service check
FRU
Action
Turn off the printer, and unplug the main motor cable at J17. Turn on the printer, and check
for the following voltages at J17:
Main motor gear drive
Main motor cable
LVPS/HVPS
Controller board
Warning: Do not
replace the operator
panel and controller
board at the same
time. Each card
contains the printer
settings. When either
of these cards is new,
it obtains the settings
from the other card.
Settings are lost when
both are new and
replaced at the same
time.
2-26
J17 pins
Voltages
Pins 1-4, 6
Approx. 5 V dc
Pins 7-9
18 V dc-24 V dc
Verify ground at pin 5 for both the card and cable.
• If these voltages are correct, then check the main motor cable for continuity.
- Remove the left side cover to access the connector on the motor.
- If continuity exists on each wire, then replace the main motor gear drive which
includes the motor.
- If continuity does not exist on one or more of the wires, then call the next level of
support.
• If these voltages are not correct, then see “Controller board connector pin values”
on page 5-2, or replace the controller board. See “Controller board removal” on
page 4-6.
Operator panel service check
Inspect the operator panel cable for damage. Make sure the cable is plugged in securely. Run POST, and check
each light for proper operation. See “Power–On Self Test (POST) sequence” on page 2-1.
LCD Operator panel service check
FRU
Action
Operator panel (LCD)
Controller board
Lights
Warning: Do not
replace the operator
panel and controller
board at the same
time. Each card
contains the printer
settings. When either
of these cards is new,
it obtains the settings
from the other card.
Settings are lost when
both are new and
replaced at the same
time.
If the LCD does not come on, then open the controller board cage and locate the operator
panel connector at J3. Make sure the cable is properly connected to the controller board
and the controller board has input voltage to it.
With the printer on, verify the following without disconnecting the cable:
• Pins 1, 3, 5, and 6: 3.3 v
• Pin 2: 5 v
• Pins 4 and 7: GND
If these are approximately correct and the operator panel is not functioning, then replace
the operator panel.
If any are incorrect, then see “Controller board service check” on page 2-22.
Buttons
If the buttons do not respond, then replace the operator panel. There is no test or repair for
the faulty switches on the operator panel.
Paper feed service checks
Paper jam error indication during POST
FRU
Action
Fuser (exit sensor)
If the exit sensor flag, which is visible at the back of the fuser, is in any position other than
vertical, then the printer will display a paper jam. Make sure the flag is operating freely.
Replace the fuser if the sensor is damaged.
Input/duplex sensor
Manual feed sensor
Make sure the input paper feed sensors are working properly. A stuck or incorrectly installed
sensor causes a paper jam indication.
Media picks but stops halfway through the printer
FRU
Action
Input/duplex sensors
(under print cartridge assembly)
Input sensor (manual)
Make sure the input sensors are working properly.
Check for a broken or stuck flag on the input sensors. Clear anything that keeps
the flags from rotating freely.
Make sure the cables are seated on the controller board at J27 (input/duplex
sensor) and J23 (manual input).
Check for +5 V dc on pin 2 and 5 at J27 (input/duplex sensors) and pin 2 at J23
(Input sensor). Voltages on pins 1 and 4 at J27 pin 1 at &23 should change as the
flags intersect with the sensor.
• If correct, then replace the input paper feed sensor.
• If these voltages are not correct, then replace the controller board.
• Check the pick tires. Clean or replace as necessary.
Diagnostics information
2-27
Media never picks
FRU
Action
Paper feed (pick tires) tray 1
Paper feed (pick tires) tray 2
Media drive ASM
Media feed clutch ASM
Manual feed clutch ASM
P/U and manual feed solenoid
ACM drive shaft
Open the left cover, and verify that the solenoids and clutches are functioning
when an attempt is made to feed the media.
Make sure the rubber tires on the ACM are installed and clean.
Replace the tires, ACM drive, clutch assemblies, solenoids, or drive shaft as
necessary.
Media occasionally mispicks or picks multiple sheets at once
FRU
Action
Tray 1
Tray 2 (option)
Check tray for media catch points.
If the sheet being fed stops momentarily, then the ACM applies additional vertical force,
causing additional sheets to feed.
Do not mix media types in one tray.
Paper pick tires
(Tray 1 or tray 2)
Check the tires in the ACM assembly for signs of wear or damage.
ACM clutch
Manual feed clutch
Media feed clutch ASM
(tray 1 only)
Manual feed clutch
solenoid
Open left cover, and observe the solenoid and clutch actions at the ACM and manual
feed shafts as a print job is attempted.
Controller board
P/U and manual feed
solenoid ASM
Disconnect the solenoid cable at J26 on the controller board and measure the resistance
across cable pins 1 and 2.
Replace the tires as necessary.
Replace the faulty part.
• The resistance should be approximately 70 ohms.
• If it is not, then replace the solenoid.
• If the resistance is approximately 70 ohms, then check the controller board. Pin 1 at
J26 should be +24 V dc. See “Controller board service check” on page 2-22 for
more information.
Replace controller board as necessary.
Media skews
FRU
Action
Paper feed (pick tires) tray 1
Paper feed (pick tires) tray 2
Tray 1
Tray 2 (option)
Check tires for debris. If tires are new, then try reversing each on its hub.
2-28
Check side guides on Tray 1 and Tray 2. Guides set for a full stack of media may
be too wide when the stack is short.
Media “trees,” wrinkles, stacks poorly, or curls
FRU
Action
Fuser
This problem is most likely due to a worn backup roll. It causes the printer to run hotter than
required for the media being printed. Excessive heat can cause media treeing problems,
poor stacking, or curl.
Print the menu sheet found under Utilities.
Look at the media settings. Some, such as card stock or rough texture, may require a
higher fuser temperature, which leads to more of these problems (except stacking) in plain
paper.
• Change settings using the printer driver.
• Use the local printer setup utility (included on the CD) to change the NVRAM
settings.
Try a different ream of paper. Moist media has a higher tendency to crease (treeing) and
curl.
Parallel or USB port service check
1. Perform a print test to make sure the printer prints correctly. Verify that the indicator light is on, then print
the menu settings by selecting Print Menu under Utilities.
2. Be sure the printer parallel cable is designed for bidirectional printing.
3. Be sure the user’s application is set up correctly.
4. If the internal print test page prints correctly, the user’s application/printer driver is set up correctly, and the
5.
correct bidirectional parallel cable is installed, but the printer still fails to print on command from the host
computer, then replace the controller board.
Check the USB cable for continuity.
Diagnostics information
2-29
Print quality service checks
Note: Ensure the cover closes tightly. A gap in the opening may allow light to expose the photoconductor,
resulting in a ‘dirty’ print. Extreme environmental conditions, temperatures, and humidity will affect the print
quality.
Using print quality test pages
To help isolate print quality problems, like streaking, print test pages using the print quality test pages. To print
the print quality test pages:
1. Enter Configuration Menu.
a. Turn off the printer.
b. Turn on the printer while pressing and holding
and
.
c. Release the buttons when Performing Self Test displays.
d. The message CONFIG MENU displays.
e. Press
to Prt Quality Pgs.
f. Press
to print the pages.
2.
3.
Four pages print to help evaluate print quality. The first page has various fonts and a graphic, the
second page is gray with graphics, the third page is black, and the last page is blank.
Use the test pages to isolate problems such as light or toner streaks. See “POST symptom table” on
page 2-20 for solutions to these problems.
Press
to Exit Config Menu and press
.
To exit configuration, turn the printer off.
Note: Refer to the print defects guide at the end of the manual for repeating defects.
Blank page
FRU
Action
Toner cartridge (not a
FRU)
Remove the toner cartridge, and gently shake it to evenly distribute the toner.
Check for cartridge damage.
Blank pages can be caused by a defective printhead assembly,
LVPS/HVPS, or controller board.
Printhead
LVPS/HVPS
Controller board
• Printhead errors typically result in printer service errors unless there is blockage of the
beam or dust on the lens. Check the lens and opening for blockage.
• Blank pages typically are caused by the PC roll not being properly charged. Try a
different PC kit.
• With the cartridge out, check the spring loaded contacts on the right side for free motion.
None should be ground except for #4 contact from the front.
Unplug the printer, and check the cable continuity between the LVPS/HVPS connector
marked OPC (at CN202) and the corresponding wire form (spring) found about 14 mm
above and to the right of the transfer roll gear.
• If there is not continuity, then call the next level of service.
Try a different toner cartridge and PC kit.
• If those fail, then replace the LVPS/HVPS, controller board, or the printhead in that
order.
Also, see “Solving print quality problems” on page 2-34.
2-30
Black page
Note: Incorrect laser exposure or incorrect charging of the photoconductor causes an all black page. Always
verify the same results from a different print cartridge assembly and developer before proceeding.
FRU
Action
Toner electrodes (not
a FRU)
Check the three rearward electrodes below the toner cartridge assembly for contamination,
damage, or a short to ground. Correct as necessary.
Check continuity between the cable (DEV, TAR, and doctor blade) connection PCN3 and
on the contact tips below the toner cartridge assembly.
• If continuity fails, then call the next level of service.
With the printer off, disconnect the LVPS/HVPS cable from J502 on the controller board.
Turn the printer on, and verify +24 V dc on pins 17 and 19 of the cable.
Verify +5 V dc on pins 1, 3, 5, 13, and 15.
Verify ground on pins 10, 12,14, 16, and 18.
LVPS/HVPS board
Controller board
Miscellaneous cables
•
•
•
•
If any of the values are incorrect, then replace LVPS/HVPS board.
If the grounds are incorrect, then check ground paths.
Check continuity in the cable. If the cable is bad, then call the next level of support.
If the values are correct and the toner electrodes are good, then replace the controller
board.
• See the “LVPS/HVPS service check” on page 2-25 and the “Controller board
service check” on page 2-22, if necessary.
Heavy background
Poor development or poorly charged toner particles cause excessive background. This is more noticeable as
the toner cartridge nears end-of-life.
FRU
Action
Toner cartridge (not a
FRU)
PC Kit (not a FRU)
Check the toner darkness setting in the driver. Try a lower setting.
Make sure the toner cartridge and PC Kit are correctly installed and the high voltage
contacts are clean.
If the toner cartridge and PC Kit are installed correctly, then try a new PC Kit first and then
toner cartridge.
Check the contacts for correct installation and contamination where contact is made
between the print cartridge assembly and spring contacts which connect to the LVPS/HVPS
board at CN203. Clean as necessary.
If this does not correct the problem, then replace the following FRUs one at a time in the
order shown:
LVPS/HVPS
Controller board
• LVPS/HVPS board (See “Black page” on page 2-31 for pin values.)
• Controller board
Diagnostics information
2-31
Partial blank image/white spots (no repeating pattern)
FRU
Action
Toner cartridge (not a
FRU)
Remove the toner cartridge assembly, and gently shake the assembly to evenly distribute
the toner.
Check to make sure that the laser light path is not blocked.
If toner cartridge is low, then try a new one.
Paper (not a FRU)
Make sure recommended media is being used.
Check the media settings in the printer driver. A heavier media may require higher heat to
properly fuse.
Variation in image density horizontally across page
FRU
Action
PC Kit (not a FRU)
The charge roll may have an unbalanced force against the PC (photoconductor) drum.
Try a new PC Kit.
Transfer roll
Note: Do not touch the transfer roll except at its ends. Place a sheet of paper over the roll to
prevent damage from finger oils or hand lotion.
Check the springs in the left and right transfer roll bearings. The bearing assemblies should
support the transfer roll, applying evenly distributed forces to the PC drum.
Replace the transfer roll assembly if the springs or bearings show signs of damage, or
fatigue.
Inspect the transfer roll for signs of wear, damage or contamination.
Replace as necessary.
Poor fusing of image
FRU
Action
Fuser
The fuser may not be operating at the proper temperature to fuse the toner to the paper.
See“LVPS/HVPS service check” on page 2-25 for more information. Try changing the
setting to heavier paper or even card stock.
Media (not a FRU)
Make sure recommended media is being used.
Check the media settings in the printer driver.
2-32
Light print
FRU
Action
Toner cartridge (not a
FRU)
Make sure the toner cartridge and PC Kit are installed correctly and that the toner cartridge
is not low on toner.
If the problem continues, then install a new toner cartridge.
Recheck condition before replacing PC Kit, if necessary.
Check the transfer roll for signs of toner buildup and contamination.
Inspect the HVPS contact (transfer roll) for contamination.
Verify the high voltage cable is plugged into the LVPS/HVPS.
Transfer roll
LVPS/HVPS card
If all components appear free of contamination, then replace the following FRUs one at a
time in the order shown:
• Transfer roll
• LVPS/HVPS card
White or black lines or bands
FRU
Action
Print cartridge
assembly (not a FRU)
Developer drive
coupling assembly
Main motor gear drive
Banding appears as light or dark horizontal lines on a uniformly gray page or on a page with
a large area of graphics. Banding is primarily due to a variation in the speed of the media as
it feeds through the printer, especially in the developer and transfer process. It may also be
a result of overly dry or moist environments.
With the printer off, check to make sure that the laser beam is not blocked.
Inspect the toner cartridge and paper feed components, especially the drive coupler and
drive gears for debris, binds, or damage.
Toner on back of page
FRU
Action
Photoconductor kit (not
a FRU)
Print a menu page found under Utilities, and check settings for media type.
Inspect the overall paper path for signs of spilled toner.
Gently clean the contaminated areas with a soft cloth.
Fuser
Inspect the fuser for signs of contamination.
Replace the fuser as necessary.
Transfer roll
A transfer roll contaminated with toner can cause toner to transfer to the back of pages.
Inspect the transfer roll for contamination and its cable for continuity.
HVPS or controller
board
Loss of the proper high voltages can cause excessive toner to contaminate the transfer
roller. None of these voltages can be measured, but the contacts and continuities can be
checked. To check the lower voltage, see J502 on the wiring diagram. Replace the LVPS/
HVPS or controller board as necessary.
Diagnostics information
2-33
Solving print quality problems
Note: Refer to the print defects guide at the end of the manual for repeating defects.
Print quality problems
Problem
Cause / action
Light or blurred
characters.
Light print
See “Light print” on page 2-33.
The toner cartridge may be getting low on toner:
•
•
•
•
Remove the toner cartridge and print cartridge assembly.
Shake it from side to side to redistribute the toner.
Reinstall it, and recheck for condition.
Make sure to use the recommended print media (see media types and sizes in the
User’s Guide).
• Use MarkVision™ Professional to define the custom type setting for media type, media
texture, or media weight.
• The toner cartridge or PC Kit may be defective. Replace the PC Kit first, and recheck.
Blurred characters
Blurred images, including characters, are usually caused by a defective printhead.
Vertical white lines
See “Vertical streaks" below.
Vertical white lines may be caused by the laser beam, which may be partially blocked. With
the printer off, clear the path or clean the lens. The toner cartridge or fuser may be
defective. Try a different toner cartridge. Inspect the fuser at its entry for debris.
Toner smudges
appear on the front or
back of the page.
Vertical or horizontal
streaks appear on the
page
• Make sure the media is straight and unwrinkled.
• Replace the PC Kit, and recheck before replacing the toner cartridge. See “Toner on
back of page” on page 2-33 for more information.
Vertical streaks
Something could be caught between the PC kit and the fuser. Check the paper path around
the fuser entry. Try a different toner cartridge.
Vertical white lines may be caused by the laser beam, which may be partially blocked. With
the printer off, clear the path or clean the lens. The toner cartridge or fuser may be
defective. Try a different toner cartridge. Inspect the fuser at its entry for debris.
Horizontal streaks
The toner cartridge or the fuser may be the cause due to excessive page count or defect.
Replace as needed.
If the lines are parallel and match the two intended ghost images, then the Form Type may
be incorrectly set. Check those settings.
The PC cleaner sump may be full. Replace the PC kit.
2-34
Print quality problems (Continued)
Problem
Cause / action
Toner smears or rubs
off the page.
• Toner is not being fused to the paper. Replace the fuser.
• Change the media texture setting in the driver. If special media is being used, such as
card stock or labels, then be sure to select the correct media type.
• Try a different kind of paper. Paper designed for copiers gives the best quality fusing.
The print is getting
light, but the printer
has not indicated it is
low on toner.
• Toner is becoming low in the cartridge.
• The Toner Low message does not display if the 1,500-page toner cartridge is installed.
• Remove the toner cartridge, and gently shake it from side to side to redistribute the
toner.
• Replace the toner cartridge.
The Toner Low
message displays.
• Remove the toner cartridge, and gently shake it from side to side to redistribute the
toner.
• Replace the toner cartridge.
Solid black areas on
transparencies
• There is a mismatch in the transparency and what the software is expecting.
• Choose a different fill pattern in the software program.
• Remove the toner cartridge, and gently shake it from side to side to redistribute the
toner.
• Try a different type of transparency.
• Replace the toner cartridge.
Faint images or
repetitive spots appear
on the page.
• Select a different media type or form type setting from the printer driver.
• Try a different type of paper. Media designed for copiers gives the best quality.
• Replace the toner cartridge.
Pages are blank.
• The print cartridge may be out of toner or defective. Replace the cartridge.
• There may be a software error. Re-initialize the printer by turning it off and back on.
• With the printer off, check the printhead beam path. If clear, then check for a printhead
error on POR. See “Printhead service check” on page 2-37.
• Also, see “Blank page” on page 2-30.
Diagnostics information
2-35
Print quality problems (Continued)
Problem
Cause / action
The printer is on and
indicates ready, but
nothing prints.
• Make sure the parallel or USB cable is not damaged and is firmly plugged into the
connector on the back of the printer.
• Make sure the toner cartridge assembly is installed properly.
• Print the menu page found under Utilities.
- If a menu settings page cannot be printed, then contact the next level of support.
- If a menu settings page can be printed, then the problem is one of the following:
• Computer
• Software program
• Cable
• (USB only) A failed controller board. Replace card.
Note: Test by unplugging USB and plugging it with the printer on. If the computer indicates
“unknown device,” then replace the controller board.
Toner Low light is on
and printing stops.
If a 3.5K or more page toner cartridge is being used and the Toner Low alarm is set to on,
then the printer stops printing until the toner cartridge is replaced.
The Error light alone is
on.
Make sure the front printer cover is closed.
The Toner Low light is
blinking, and the Error
light is on.
• Make sure the toner cartridge is installed correctly.
• Install a new toner cartridge.
The media skews or
buckles.
• Tray is overfilled or media is too loose.
• Don’t overfill Tray 1 or the optional Tray 2 (see media capacities in the media types and
sizes table in the User’s Guide).
• Make sure the paper guides are flush against the edges of the media.
The media sticks
together, resulting in
the printer feeding
multiple sheets.
• The friction between sheets is too high.
• Remove the media from Tray 1 or Tray 2, and fan it.
• Don’t overfill Tray 1 or the optional Tray 2 (see media capacities in the media types and
sizes chart in the User’s Reference).
The media fails to feed
from Tray 1.
•
•
•
•
The media fails to feed
from the optional
Tray 2.
•
•
•
•
•
Load Paper displays
even though there is
media loaded in the
optional Tray 2.
•
•
•
•
The input sensor does not sense media after picking.
Make sure the tray is pushed all the way in.
Press
.
Check the feed tires. (See two preceding actions.)
The printer does not
print after a paper jam
has been cleared.
•
•
•
•
The printer is waiting on the next command.
Clear all jams.
Press and release
, or open and close the printer cover to restart the printer.
Make sure the print cartridge assembly is installed properly.
2-36
Frictional force between tires and media is less than resisting force.
Remove the media from Tray 1, and fan it.
Make sure Tray 1 is selected from the printer driver. Do not overfill the tray.
Check the condition of the rubber on the paper feed rolls. Replace if worn or
contaminated.
• Verify that the ACM clutch is functioning correctly.
Incorrect tray selection or inadequate picking force by tires.
Make sure the correct tray and media type are selected from the driver.
Make sure the tray is pushed all the way in.
Remove the media from the optional Tray 2, fan it, and reload.
Check the rubber on the paper feed tires for dirt or any other debris. Replace as
necessary.
• Check the paper path in the tray for burrs or debris that may hinder media movement.
• Make sure the media does not exceed the stack height indicator.
Print quality problems (Continued)
Problem
Cause / action
Unexpected
characters print, or
characters are
missing.
•
•
•
•
Ensure correct printer driver is being used.
Select hex trace mode to determine what the problem is.
Restore factory defaults.
Make sure the parallel cable or USB cable is firmly plugged in at the back of the printer.
Jobs are not printing,
and an error message
is displayed.
• The printer is waiting for an appropriate command.
• Make sure the print cartridge assembly is installed properly.
• Make sure the printer front cover is closed.
While in PostScript 3
emulation, the printer
is flushing data (an
error message is
displayed).
• Ensure the correct PostScript driver is being used.
• The printer doesn’t have enough memory to print the job. Install more memory.
Printhead service check
FRU
Action
Turn the printer off.
Disconnect the printhead cables from J8 and J100 on the controller board.
Turn the printer on with the front door closed.
Printhead
Note: New printhead
must be aligned. See
“Printhead assembly
electronic
adjustment” on
page 3-16.
On the controller board, verify +5 V dc on pin 10 at J8 and +5 V dc on pins 1, 2, and 3 at
J100.
Verify grounds on pins 2, 4, and 7 at J8 and on pin 4 at J100.
• If voltages or grounds are incorrect, then check the controller board. See “Controller
board service check” on page 2-22 for more information.
• If voltages are correct, then replace the printhead (comes with cables).
Transfer roll service check
FRU
Action
Note: Do not touch the transfer roll except at its ends. Place a sheet of paper over the roll to
prevent damage from finger oils or hand lotion.
Check the springs in the left and right transfer roll bearings. Do not try to move the left
spring. The bearing assemblies should support the transfer roll, applying evenly distributed
forces to the PC drum.
Transfer roll
Replace the transfer roll assembly if the springs or bearings show signs of damage, or
fatigue.
Inspect the transfer roll for signs of wear, damage or contamination.
Replace as necessary.
Diagnostics information
2-37
Tray 2 service check
FRU
Action
Tray 2
Turn the printer off.
Separate the printer from Tray 2.
Turn the printer on and check the voltages on connector J28 on the controller board. See
the wiring diagram at the end of the service manual, or “Controller board connector pin
values” on page 3-2 for the J28 connector.
Pins 1, 4: 3.3 V
Pin 2: 24 V
Pin 6: Ground
If the voltages are incorrent, then replace the controller board. If the voltages are correct,
then try using Tray 2 again. If the printer error persists, then replace Tray 2.
2-38
3. Diagnostic aids
Accessing service menus
There are two different test menus that can be accessed during POR to identify problems with the printer.
Configuration Menu
Diagnostics Mode
1. Turn off the printer.
2. Press and hold
and
.
3. Turn on the printer.
4. Release the buttons when Performing Self
Test displays.
5. The message CONFIG MENU displays on the
top line of the operator panel.
The Configuration menu group contains a set
of menus, settings, and operations which are
infrequently required by a user. Generally, the
options made available in this menu group are
used to configure a printer for operation.
1. Turn off the printer.
2. Press and hold
and
.
3. Turn on the printer.
4. Release the buttons when Performing Self
Test displays.
The Diagnostic menu group contains the
settings and operations used while
manufacturing and servicing the printer.
See “Available menus” on page 3-2.
See “Menus may vary depending on the
features and options of the printer.” on
page 3-5.
Printing menus
To print a listing of the states and settings of the printer:
1.
2.
3.
4.
At the Ready prompt, press
under Menu until Utilities appears.
Press
.
Press
until Print Menus appears.
Press
.
Diagnostic aids
3-1
Configuration menu (CONFIG MENU)
Entering Configuration Menu
1.
2.
3.
4.
Turn off the printer.
Press and hold
and
.
Turn on the printer.
Release the buttons when Performing Self Test displays.
Available menus
The menus display on the operator panel in the order shown:
Configuration menu settings
Reset PC Cnt
See “Reset photoconductor maintenance counter (Reset PC
Cnt)” on page 3-3.
Prt Quality Pgs
See “Print quality pages (Prt Quality Pgs)” on page 3-3.
Reports
See “Reports” on page 3-3.
• Menu Settings Page
• Event Log
Panel Menus
See “Panel Menus” on page 3-3.
PPDS Emulation
See “PPDS Emulation” on page 3-3.
Demo Mode
See “Demo Mode” on page 3-4.
Factory Default
See “Factory Defaults” on page 3-4.
Energy Conserve
See “Energy Conserve” on page 3-4.
Font Sharpening
See “Font Sharpening” on page 3-4.
Exit Configuration Menu
See “Exit Configuration Menu (Exit Config Menu)” on page 3-4.
Note: Menus may vary depending on the features and options of the printer.
3-2
Reset photoconductor maintenance counter (Reset PC Cnt)
The reset photoconductor maintenance counter resets the photoconductor kit page counter and clears any
warnings or photoconductor exhausted messages. This operation should be performed only after a new
photoconductor unit has been installed.
Print quality pages (Prt Quality Pgs)
The print quality test pages can be printed from either the Diagnostics menu or Configuration Menu (CONFIG
MENU). When printed from the Diagnostic mode, additional information is included, and the print cartridge
lockout is bypassed. See “Print quality pages (Prt Quality Pgs)” on page 3-3. Additional configuration
information may be included on the print quality pages which is not included on the print menu page.
To print the Print Quality Test Pages, select Prt Quality Pgs from CONFIG MENU. The message Printing
Quality Test Pages is displayed.
The print quality test consists of four pages. Page one contains device information, cartridge information, margin
settings, minimum stroke width, and a mixture of graphics and text. Page two is a gray page containing two
graphics, page three is black, and page four is blank. If the duplex is turned on, then the pages are duplexed.
The Print Quality Test pages are printed in English and must always be printed on letter, legal, or A4 paper.
Reports
The Reports menu contains two selections: Menu Settings Page and Event Log.
Menu Settings Page
The Menu Settings Page contains information...
To print the Menu Settings page, press
. Press
to return to the Configuration menu.
Event Log
The event log provides a history of printer errors. The event log can be printed only in the Configuration
menu. Additional options are available in the Diagnostics menu. See “Event log” on page 3-14.
To print the event log:
1. Select Print Event Log from the Event Log menu.
2. Press
to return to the Configuration menu.
Note: An event log printed from the CONFIG MENU will not contain debug information or secondary
codes for 900 service errors. However, the event log printed from DIAGNOSTICS mode does include this
information.
Panel Menus
The settings are On and Off. The default is On.
PPDS Emulation
This menu item activates or deactivates PPDS emulation data stream. The selections are Deactivate (default)
and Activate. When PPDS emulation is activated, the following settings are also changed:
• SmartSwitch settings for each port are turned off.
• The printer language is changed to PPDS Emulation.
Users can still switch languages on the operator panel and through the PJL data stream.
Diagnostic aids
3-3
Demo Mode
This setting contains a built-in demonstration mode. The settings allow you to turn the Demo Mode Off (default)
or On. While Demo Mode is set, the printer will start in Demo Mode until you change the setting.
Note: While Demo Mode is set to On, only demonstration files can print. Files received across the network or
from the host computer are ignored.
Factory Defaults
This setting enables a user to restore all the printer settings to the original factory settings. The selections are
Do not restore (default) and Restore now. Network does not appear unless you have a network printer. The
following settings are not changed:
• Display language
• Settings in the NETWORK/PORTS MENU group.
Energy Conserve
This menu controls what values appear on the Power Saver menu. If Off is selected in the Energy Conserve
menu, then the Power Saver can be turned off. If On (default) is set in Energy Conserve, then the Power Saver
feature cannot be turned off.
Font Sharpening
This menu allows a user to set a text point-size value below which the high frequency screens will be used when
printing font data. For example, if this setting’s value is “24,” then all fonts sized 24 points or less will use the
high-frequency screens. To increase this setting’s value by 1, press
. To decrease this setting’s value by 1,
press
.
Exit Configuration Menu (Exit Config Menu)
Press
3-4
to exit the Configuration menu. The printer performs a POR and restarts in normal mode.
Diagnostics menu
Entering Diagnostics menu
1. Turn off the printer.
2. Press and hold
and
.
3. Turn on the printer.
4. Release the buttons when Performing Self Test displays.
Available tests
The menus display on the operator panel in the order shown:
Diagnostic menu settings
Registration
See “Registration” on page 3-6.
Print tests
See “Print tests” on page 3-7.
Hardware tests
See “Hardware tests” on page 3-8.
Duplex tests (if installed)
See “Duplex tests” on page 3-9.
Input tray tests
See “Input tray tests” on page 3-10.
Output bin tests
See “Output bin tests” on page 3-11.
Base sensor test
See “Base sensor test (B. sensor test)” on page 3-11.
Printer setup
See “Printer setup” on page 3-12.
EP setup
See “EP setup” on page 3-13.
Event log
See “Event log” on page 3-14.
Exit Diagnostics
See “Exit Diagnostics” on page 3-15.
Note: Menus may vary depending on the features and options of the printer.
Diagnostic aids
3-5
Registration
The Registration menu settings adjust the black plane’s margins. To set print registration, select
REGISTRATION from the Diagnostics menu. The following will display:
REGISTRATION
Top Margin
Note: Pressing
will display one margin setting per line below the REGISTRATION header.
The REGISTRATION settings and values are:
Setting
Value
Top Margin
-16...16 (0)*
Bottom Margin
-20...20 (0)*
Left Margin
-25...25 (0)*
Right Margin
-128...127 (0)*
Print Quick Test Page
None
Margins
To change the value of any margin setting, press
or
to increase or decrease the margin setting value, and
then press
to save. The panel displays Submitting changes... and returns to the initial REGISTRATION
menu screen. To exit the margin setting menu without changing the setting’s value, press
.
Top Margin
This setting moves the black plane’s top margin up or down. Increasing the margin value moves text down the
page and increases the amount of space between the page’s top edge and the top margin. Decreasing the
margin value moves text up the page and narrows the amount of space between the page’s top edge and the
top margin. The default margin is 1/6 inch.
Note: Modifying the top margin moves the entire image either up or down on the physical page. In order to
preserve the bottom margin, changing the top margin does not compress or expand the image.
Bottom Margin
This setting moves the black plane’s bottom margin up or down. Increasing the margin value moves text down
the page and narrows the amount of space between the bottom edge of the page and the bottom margin.
Decreasing the margin value moves text up the page and widens the amount of space between the bottom edge
of the page and the bottom margin. The default margin is 1/6 inch.
Note: Modifying the bottom margin affects the rate of the stepper motor and may cause the page image to
be compressed or expanded.
Left Margin and Right Margin
These settings move the position of the black plane’s margin right or left. Increasing the margin value moves the
margin to the right. Decreasing the margin value moves the margin to the left. The default margin is 1/4 inch.
Note: Modifying the left and right margins moves the entire image left or right on the physical page. In
order to preserve the right margin, changing the left margin does not compress or expand the image.
3-6
Quick Test page
Print a Quick Test page to verify that the REGISTRATION margin values are set appropriately. The Quick Test
page consists of the following:
•
•
•
•
Alignment diamonds
Horizontal lines used for skew adjustment
General device information (current page count, installed memory, etc.)
The printer’s serial number, code levels, and print registration settings
While the Quick Test page prints, Printing... will display. No buttons are active while the Quick Test page
prints. When the Quick Test page is finished printing, the display returns to the initial REGISTRATION menu
screen.
Note: Print the Quick Test page on Letter- or A4-sized media.
Print tests
This setting tests the printer’s ability to generate printed output from each of its installed input sources and to
test the printer’s current print quality.
Input sources
PRINT TESTS contains the following installed input sources:
• Tray1
• Manual Feeder
• MP Feeder
Press
or
to scroll through the PRINT TESTS menu, and then press
to select the desired input source.
Single or Continuous is displayed on the screen. A Single test feeds one sheet of media from the selected input
and prints a test page on it. No buttons are active during the Single test. The Continuous test feeds media from
the selected input and prints test pages until
is pressed. The printer always generates a simplexed
version of the Print Test page in its default resolution. While the Single or Continuous tests print, Printing...
will display. After the Single test prints or the Continuous test is canceled, the display returns to the PRINT
TESTS menu screen.
Note: The type of media installed in the selected input source will affect the contents of the page.
Print Quality Pages (Prt Quality Pgs)
This setting reports the values of a broad range of printer settings and tests the printer’s ability to generate
acceptable printed output. Press
to print the report. Printing Quality Test Pages will display. Once started,
the printing cannot be canceled and no buttons are active until the printing completes.
Diagnostic aids
3-7
Hardware tests
This setting contains the following tests:
• LCD Test
• Button Test
• DRAM Test
Press
or
to scroll through the Hardware Tests menu, and then press
to select the desired test.
LCD Test
Once the LCD Test setting is selected, the printer automatically performs the operator panel test. This test
toggles each pixel in the operator panel through every contrast level, beginning with the darkest and ending with
the lightest. Once the pixels are toggled, the backlight of the operator panel comes on, and then goes off. Nonfunctioning pixels will appear as blank spaces during the test’s darker stages. Press
anytime to cancel the
LCD Test. Once the test is canceled, the display returns to the initial Hardware Tests screen.
Button Test
The Button Test verifies the operation of each button on the operator panel. Press
to select the Button Test
from the HARDWARE TESTS menu. All of the buttons and the backlight illuminate, and PANEL TEST Press
Count: 0 displays. Press , , or
to increase the value of the Press count field by one. If the final Press
count does not match the total number of buttons that are pressed, then one or more buttons are malfunctioning.
Press
to return to the HARDWARE TESTS menu screen.
DRAM Test
The purpose of this test is to check the validity of DRAM, both standard and optional. The test writes patterns of
data to SDRAM to verify that each bit in memory can be set and read correctly.
To run the SDRAM Memory Test:
1. Select DRAM Test from the menu. The power indicator blinks, indicating the test is in progress.
DRAM Test
P:######
xxxMb
F:#####
xxxMb represents the amount of installed DRAM memory in MB.
P:###### represents the number of times the memory test has passed and finished successfully. Initially, 000000
displays with the maximum pass count being 999,999.
F:##### represents the number of times the memory test has failed and finished with errors. Initially, 00000
displays with the maximum fail count being 99,999.
2. Once the maximum pass count or fail count is reached, the test stops, the power indicator is turned on
3.
3-8
solid, and the final results display. If the test fails, then the message DRAM Error displays for approximately
three seconds and the failure count increases by 1.
To stop the test before it completes, turn off the printer.
Duplex tests
The following tests are used to determine if the duplex is working correctly:
•
•
•
•
•
Quick Test
Top Margin
Left Margin
Sensor Test
Duplex Feed 1
Quick Test
The Quick Test contains the following information on a duplexed page:
•
•
•
•
Print registration settings
Alignment diamonds at the top and bottom
Horizontal lines to check for skew
General printer information, including current page count, installed memory, serial number,
and code level.
To print the duplexed Quick Test page:
1. Select Quick Test from the DUPLEX TESTS menu.
2. Select Single or Continuous by pressing or .
3. Press
to print the page.
Top Margin
1. Select Top Margin from the DUPLEX TESTS menu.
2. To change the margin value, press
to increase the value or
3. Press
to save the desired margin value.
to decrease the value.
Left Margin
1. Select Left Margin from the DUPLEX TESTS menu.
2. To change the margin value, press
to increase the value or
3. Press
to save the desired margin value.
to decrease the value.
Sensor Test
This test is used to determine if the input sensor is operating correctly.
• If the sensor is operating correctly, then OP (Open) will appear on the display:
Sensor Test
Input=OP
• Press
to return to the DUPLEX TESTS menu.
Diagnostic aids
3-9
Duplex Feed 1
1. Select Duplex Feed 1 from the DUPLEX TESTS menu. The following will appear on the display:
Duplex Feed 1
Feeding...
2. A blank page will feed through the printer. The following will appear on the display:
Duplex Feed 1
Clear Paper...
3. Remove the blank page from the printer, and press
to return to the DUPLEX TESTS menu.
Input tray tests
The INPUT TRAY TESTS setting is used to test the printer’s installed input trays and their sensors.
Feed Tests
The Feed Test observes the paper path of media as it passes through the printer. This setting contains the
following tests:
• Tray 1
• Tray 2
• MP Feeder, if installed
To observe the paper path, open the upper rear door during the feed test.
Note: The upper front door cannot be opened during the feed test.
The feed test can be performed by using media from any if the installed input sources. All pages used during this
test drop into the default output bin. For each installed input source, press
to select Single or press
and
to select Continuous. The Single test feeds one sheet of media to the default output bin. The Continuous
test feeds media to the default output bin until
is pressed. The operator panel displays [Select Input
Tray] Feeding... while either of these tests perform.
Sensor Test
The Sensor Test verifies that the Tray 1, Tray 2, and MP Feeder (if installed) sensors are working correctly.
Press
to select this test from the INPUT TRAY TESTS menu. [Select Input Tray...] Tray Present will
display on the operator panel.
3-10
Output bin tests
The Output bin tests setting is used to test the printer’s output bins and its sensors.
Feed Tests
This test verifies that the media from the printer’s default input source feeds to the specific output bin. Press
to select Single, or press
and
to select Continuous. The Single test feeds one sheet of media to the
default output bin. No buttons are active during this test. The Continuous test feeds media to the default output
bin until
is pressed. The indicator light blinks green, and the operator panel displays [Select Output Bin]
Feeding... while either of these tests perform.
Sensor Test
This test verifies that the selected output bin’s sensors are working correctly. The following sensors are available
in each output bin:
Output bin
Full sensor
Near full sensor
Passthru 1
sensor
Passthru 2
sensor
Level sensor*
Standard bin
✔
x
x
x
x
-bin Mailbox
x
x
✔
✔
✔
*This sensor will register the following levels: “empty,” “normal,” “near full,” and “full.
Press
to select this test from the Output bin tests menu, and then press
again to select the desired
output bin. Closed will display on the operator panel if the sensor is closed. Open will display on the operator
panel if the sensor is open. If the wrong message is displayed, then the sensor is malfunctioning. To exit the
Sensor Test, press
or
.
Base sensor test (B. sensor test)
The Base Sensor Test verifies the correct functioning of the following sensors:
•
•
•
•
•
•
•
•
•
•
•
Input
Sensor Tests
Front Door
Standard bin
S1
S2
Fuser Exit
C-TMC
M-TMC
Y-TMC
K-TMC
This test toggles each of these sensors. If a sensor does not toggle, then the sensor is malfunctioning. To exit
the Base Sensor Test, press
or
.
Diagnostic aids
3-11
Printer setup
Printer Setup displays the following selections:
•
•
•
•
•
•
•
•
•
Defaults (U.S.*, Non-U.S.)
Page Count
Perm Page Count
Serial Number
Engine Setting (1 through 4)
Model Name
Configuration ID
Edge to Edge
Par S Strobe Adj (only displayed if the printer has a standard parallel port)
Defaults
The value of this setting determines whether the printer uses the U.S. or Non-U.S. factory default value for the
settings listed below:
Device Setting
U.S. value
Paper sizes
Envelope size
PCL Symbol Set
PPDS Code Page
Universal Units of Measure
Non-U.S. value
Letter
A4
10
DL Envelope
PC-8
PC-850
437
850
Inches
Millimeters
If the value of a setting is changed, then Submitting Changes... displays. Press
and return to the Printer Setup menu.
to exit the Defaults setting
Printed Page Count (Page Count)
The value of this setting gauges the amount of usage on the printer. The Page Count setting’s value will equal
the values of the Picked Sides meter. After all print tests have been completed, the value will reset to “0.”
Note: The value of this setting cannot be changed manually.
Press
to exit the Page Count setting and return to the Printer Setup menu.
Permanent Page Count (Perm Page Count)
The value of this setting indicates the total number of pages that have been printed. After all print tests have
been completed, the value will reset to “0.”
Note: The Permanent Page Count’s value cannot be reset.
Press
to exit the Permanent Page Count and return to the Printer Setup menu.
Serial Number
The serial number can only be viewed and cannot be changed.
To view the serial number:
1. Select Serial number from PRINTER SETUP.
2. Press Return to return to PRINTER SETUP.
3-12
Service Tag (only on some printers)
The service tag number can only be viewed and cannot be changed.
1. Select Service Tag from the PRINTER SETUP menu.
2. Press Back to return to PRINTER SETUP.
Engine Setting 1 through 4
Warning: Do not change these settings unless requested to do so by your next level of support.
Model Name
The serial number can only be viewed and cannot be changed.
Configuration ID
The configuration ID is used to communicate characteristics of certain areas of the printer that cannot be
determined by hardware sensors. The configuration ID was originally set when the printer was manufactured
and is located on the printer label.
Edge to Edge
When Edge to Edge is set to On, text and graphics are printed with all margins set to the physical edges of the
page. This feature does not work in PPDS emulation.
Par S Strobe Adj (parallel strobe adjustment)
This setting adjusts the factory setting for the amount of time the strobe is sampled to determine that valid data
is available on the parallel port. Incrementing this value by one means the strobe is sampled 50 nanoseconds
longer. The range of values are between -4 and +6, in increments of one. A value of zero indicates no change is
made from the factory setting.
EP setup
EP Setup displays the following selections:
•
•
•
•
•
•
EP Defaults
Fuser Temperature (Fuser Temp)
Transfer
Print Contrast
Gap Adjust
Automatic Darkness Adjustment (Auto Dark Adj)
EP Defaults
Restores all EP settings to factory default values. Selections are Restore and Do Not Restore.
Fuser Temperature (Fuser Temp)
Changing this setting can reduce media curl or melting of some letterhead images. Selections are Normal
(default), Lower, and Lowest.
Transfer
The transfer can be adjusted to Low, Medium, or High. The default setting is Medium.
Diagnostic aids
3-13
Print Contrast
The print contrast can be adjusted to Low, Medium, or High. The default setting is Medium.
Charge Roll
The charge roll can be adjusted to Low, Medium, or High. The default setting is Medium.
Gap Adjust
Adjusts the minimum gap between sheets during printing. This setting reduces speed (pages per minute), but
can be used to reduce curl of printed media and improve stacking in the output bin.
The range is 0 (default) to 255. Adjusting by one results in 9 mm of increased gap.
Automatic Darkness Adjustment (Auto Dark Adj)
This setting attempts to optimize the amount of toner used when printing with a specific operating point. Each
time this setting executes, the printer performs the following:
•
•
•
•
•
•
Calibrates its toner density sensor
Measures the reflectivity of its bare drum
Prints patches on the drum and measures the drum’s reflectivity through the patches
Cleans the transfer roll
Calculates reflectivity ratios and operating points in order to attain each operating point’s
darkness target
Modifies the EP mechanism as necessary to adjust toner darkness.
No messages are displayed on the operator panel to give any indication that this test is running. When
deactivated, the printer disables.
Event log
Display Log
Selecting EVENT LOG provides a history of printer errors. The most recent error displays in position 1, and the
oldest error displays in position 10 (if 10 errors have occurred). If an error occurs after the log is full, then the
oldest error is discarded. Identical errors in consecutive positions in the log are entered. All 2xx and 9xx error
messages are stored in the event log as well as the PC kit and maintenance counter resets and NVRAM resets
initiated by the Factory Defaults setting in the UTILITIES menu.
To view the display log:
1. Select Display Log from the EVENT LOG menu.
The error log is displayed one error per display screen. For example:
Event 1/6
936 Svc Error
This error is the first of six errors (it is also the latest error). This error was a 936 service error. To see the
second service error, press
. Pressing
will display the sixth error as shown:
Event 6/6
202.01 Paper Jam
2. Press Back once to exit the Display log, or press twice to exit the EVENT LOG.
3-14
Print Log
Additional diagnostic information is available when you print the error log. Some of the additional information
includes:
• Detailed printer information, including model and serial number
• Time and date stamps
• Page counts for each error
The printed error log can be faxed to Dell or your next level of support for verification or diagnosis. This report
can also be printed from the Configuration Menu. Because you can clear error logs, the contents of this log
may not match the contents when you view the error log.
To print the error log:
1. Press
to enter Print Log from the EVENT LOG menu.
2. Press Back to exit the EVENT LOG menu.
Clear Log
1. Select Clear Log from the Error Log menu.
Clear Log
=Yes
2. Select No to exit without clearing the log. Press Yes to confirm. The log is immediately erased, and the
display indicates No Events Logged.
3. Press Return to exit the Clear Log menu after clearing the log.
Exit Diagnostics
Selecting EXIT DIAGNOSTICS exits the Diagnostics menu, and Resetting the Printer displays. The printer
performs a POR, and the printer returns to normal mode.
Diagnostic aids
3-15
Printhead assembly electronic adjustment
A step-by-step process to align a new printhead.
Note: Before aligning the printhead electronically, first align the printhead mechanically, if needed. See
“Printhead assembly mechanical adjustment” on page 3-17
1. Enter the Diagnostics menu. See “Entering Diagnostics menu” on page 3-5.
2. Press
to enter the Registration menu.
3. Press
to print the Quick test page.
Quick Test page
(sample only; use actual sheet)
4. In the Registration menu, select the right margin setting.
5. To determine the margin setting, choose the value that is closest to the darkest bar on the center graph of
the margin page. Add that value to the current right margin setting printed on the left hand side of the
margin page. (The right margin setting will also appear on the operator panel display.) For example, if the
right margin setting on the page is -2, and the number that is closest to the darkest line on the graph is 3
(-2+3), then the right margin setting will be equal to +1.
6. Press
or
to the desired setting, and press
.
7. Print the Quick Test page again and check that the darkest line in the center graph is equal to zero. If it is,
then check to see if the left, top, and bottom margins are detected. If it is not, then repeat step 5.
Note: The alignment of the left margin positions the black plane to the right or left. The alignment of the right
margin does not alter the margins and should only be used to adjust the printhead.
3-16
Printhead assembly mechanical adjustment
A printhead needs to be correctly positioned after it has been removed. Use a pencil to mark the screw locations
of the old printhead on the metal frame. Align the new printhead relative to the location of the old printhead.
Note: Skew is caused by a sheet being fed through the printer while misaligned. The entire image is rotated
relative to the sheet edges. However, a mechanically misaligned printhead causes the horizontal lines to appear
skewed while the vertical lines remain parallel to the vertical edges.There are no adjustments for skew. Check
the pick roll (paper pick assembly) for wear, the paper path for obstructions, the fuser for proper setting, and the
tray paper guides for fit to the media.
Paper feed
skew
Printhead
misalignment
To adjust the printhead:
1.
2.
3.
4.
5.
6.
Enter the Diagnostics Menu. See “Entering Diagnostics menu” on page 3-5.
Select PRINT TESTS.
Select Tray 1.
Select Single.
Fold the printed test page on the left side so that a few millimeters of grid lines wrap around the outside of
the fold. See photo below.
Fold a second vertical fold near the center so that the left side top edge aligns with the right side top edge.
Diagnostic aids
3-17
7. If the grid lines of the right flap align below the corresponding lines on the left flap, then adjust the printhead
clockwise relative to the printer and recheck. (See the left side of the figure below.) If the grid lines of the
left flap align below the corresponding lines of the right side, then adjust the printhead counterclockwise.
(See the right side of the figure below.)
8. After obtaining a properly adjusted image on the paper, tighten all three screws.
Note: The printhead must be aligned electronically. See “Printhead assembly electronic adjustment” on
page 3-16.
3-18
4. Repair information
Warning: Read the following before handling electronic parts.
Handling ESD-sensitive parts
Many electronic products use parts that are known to be sensitive to electrostatic discharge (ESD). To prevent
damage to ESD-sensitive parts, follow the instructions below in addition to all the usual precautions, such as
turning off power before removing logic cards:
• Keep the ESD-sensitive part in its original shipping container (a special “ESD bag”) until the
part is ready to be installed into the printer.
• Make the least-possible body movements to prevent an increase of static electricity from
clothing fibers, carpets, and furniture.
• Put the ESD wrist strap on your wrist. Connect the wrist band to the system ground point. This
discharges any static electricity in your body to the printer.
• Hold the ESD-sensitive part by its edge connector shroud (cover); do not touch its pins. If a
pluggable module is being removed, then use the correct tool.
• Do not place the ESD-sensitive part on the MFP cover or on a metal table; if the ESDsensitive part needs to be put down for any reason, then first put it into its special bag.
• Machine covers and metal tables are electrical grounds. They increase the risk of damage
•
•
•
because they make a discharge path from your body through the ESD-sensitive part. (Large
metal objects can be discharge paths without being grounded.)
Prevent ESD-sensitive parts from being accidentally touched by other personnel. Install
machine covers when the machine is not being worked on, and do not put unprotected ESDsensitive parts on a table.
If possible, keep all ESD-sensitive parts in a grounded metal cabinet (case).
Be extra careful in working with ESD-sensitive parts when cold-weather heating is used,
because low humidity increases static electricity.
Repair information
4-1
Removal procedures
Note:
• Remove the toner cartridge and media tray before removing other printer parts. The toner cartridge should
•
•
•
•
4-2
be protected from light while out of the printer.
We recommend disconnecting all external cables from the printer to prevent damage during service.
Unless otherwise stated, reinstall the parts in reverse order of removal.
When reinstalling a part held with several screws, start all screws before final tightening.
Remove the paper tray and print cartridge before proceeding with a removal.
ACM pick tire roller removal
1. Place the printer on its side.
Note: Be careful to not mar the finish of the printer.
2. Open the duplex jam door just far enough to pull out the ACM pick tires.
Warning: Open the duplex door only far enough to remove the ACM pick tires. If the door is opened too far,
then it can become disengaged and interfere with the paper tray. The tray may go in but will not
come out, and will render the printer as non-serviceable.
3. After the ACM pick tires have been pulled out, close the duplex door.
Repair information
4-3
4. Remove the ACM pick tire roller (A).
Note:
• If the left hub is gray, then disconnect the old right and left tire/hub assemblies from the ACM, and replace
with the new right and left tire/hub assemblies.
• If the left hub is black, then remove the old right and left tires from the ACM hubs, and replace with the new
tires. Do not attempt to remove the hubs.
A
4-4
Bezel removal
1. Open the front access door.
2. Flex the top of the bezel, and disconnect the latch (A) from the upper front cover.
3. Disconnect the latches (B) from the upper front cover.
4. Remove the bezel.
Repair information
4-5
Controller board removal
CAUTION
This product contains a lithium battery. THERE IS A RISK OF EXPLOSION IF THE BATTERY
IS REPLACED BY AN INCORRECT TYPE. Discard used batteries according to the battery
manufacturer’s instructions and local regulations.
Warning:
•
•
•
•
1.
2.
Always touch a ground before touching the board.
Handle the board carefully by the edges.
Never replace the operator panel and controller board without a successful POR in between.
Never replace the operator panel and the controller board at the same time. Each card contains the printer
settings. When either of these cards is new, it obtains its settings from the other card. Critical factory
settings are lost when both cards are new and are replaced at the same time.
Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
Remove the three screws (A) from the USB port.
A
4-6
3. Disconnect all of the cables from the controller board.
Note: A drip guard (B) has been added below the controller board. The drip guard may need to be removed to
access to the controller board.
B
4. Remove the five screws (C) from the controller board.
C
5. Lift the controller board, and remove.
Note: When installing the controller board, place the USB port and parallel port screws first, and then place the
controller board screws.
Repair information
4-7
Cover open sensor
1. Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
2. Disconnect the cable (A) from the controller board.
3. Use a #1 Phillips screwdriver to remove the screw (B) holding the sensor.
B
4. Remove the cover open sensor.
4-8
A
Door mount removal
1.
2.
3.
4.
5.
Open the front cover.
Remove the lower front cover. See “Lower front cover removal” on page 4-25.
Remove the left side cover. See “Left side cover removal” on page 4-23
Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
Disconnect the operator panel cable (A).
6. Remove the cable through the opening.
7. Remove the three screws (B) from the right side of the printer.
Repair information
4-9
8. Disconnect the fuser link (C).
C
9. Remove the three screws (D) from the left side of the printer.
10. Remove the door mounts.
4-10
Duplex removal
1. Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
2. Remove the LVPS/HVPS. See “LVPS/HVPS removal” on page 4-27.
3. Remove the three screws (A) from the shield.
A
4. Remove the four screws (B) from the duplex.
B
Repair information
4-11
5. Lift the duplex slightly, push to the left, and tilt to clear the right side of the printer.
6. Remove the duplex.
4-12
Duplex/main motor gear drive interface removal
1.
2.
3.
4.
Remove the LVPS/HVPS. See “LVPS/HVPS removal” on page 4-27.
Remove the duplex. See “Duplex removal” on page 4-11.
Remove the main motor gear drive. See “Main motor gear drive removal” on page 4-30.
Remove the e-clip (A) from the gear.
5. Remove the gear (B) and gear shaft (C).
Repair information
4-13
6. Remove the screw (D) from the gear (E).
7. Remove the plastic bushing (F).
4-14
8. Use a screwdriver to loosen the retainer clip (G) from the gear.
9. Remove the gear (H).
Repair information
4-15
Fan removal
1. Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
2. Disconnect the cable (A) from the controller board, and remove the two screws (B) holding the fan to the
right side frame.
B
3. Remove the fan.
4-16
A
B
Front access door removal
1. Remove the operator panel. See “Operator panel removal” on page 4-51.
2. Remove the left side cover. See “Left side cover removal” on page 4-23.
3. Remove the upper front guide assembly. See “Upper front guide assembly removal” on page 4-64,
steps 1-3.
4. Close the front access door.
5. While closing the MPF cover, pull up on the MPF by the steel shaft until the MPF lifts from its hinges.
Repair information
4-17
6. Disconnect the MPF from the lower front cover.
7. Disconnect the fuser link (A) from the front access door.
A
4-18
8. Disconnect the front access door cable (B), and pull it through the opening to clear the side frame.
B
9. Disconnect the front access door from its hinges, and remove.
Repair information
4-19
Fuser removal
1. Remove the rear exit guide. See “Rear exit guide assembly with sensor and reversing solenoid
removal” on page 4-56.
2. Remove the two screws (A).
3. Partially pull the fuser forward for better access.
4. Push in on the cable connector cover (B), and remove.
4-20
5. Disconnect the AC cable (C).
C
B
6. Disconnect the thermistor cable (D).
D
Repair information
4-21
7. Disconnect the exit sensor cable (E) from the controller board.
E
8. Remove the fuser.
Note:
• Be careful to not damage the gears during the fuser installation.
• Be sure to reinstall the AC cable during the fuser installation.
4-22
Left side cover removal
Note:
•
•
1.
2.
Leave the front door closed when removing the left side cover.
Make sure that the fuser cables are out of the way when removing the left side cover.
Remove the paper tray.
Remove the screw (A) from the rear left side of the printer.
A
3. Remove the screw (B), and press the two latches (C) on the bottom of the left side cover.
B
C
Repair information
4-23
4. Swing the cover open, and lift to remove the left side cover.
Note: There are two tabs on the top of the left side cover. Do not swing the left side cover open too far, or the
tabs will be damaged.
4-24
Lower front cover removal
1. Open the lower front cover.
2. Disconnect the MPF pins (A) from the right and left sides of the lower front cover.
Note: The picture below shows the E260d, E260dn printer. The lower front cover removal is the same for all
models.
A
3. Flex the lower front cover, and disconnect it first from its right hinge and then from its left hinge.
Note: An alternative to step 3 is to remove the front access door, and remove the three screws from the right
door mount. See “Front access door removal” on page 4-17 and “Door mount removal” on page 4-9.
Repair information
4-25
Installation note: Use a flathead screw driver to press in on the door mount (B) while pulling on the front access
door to connect the cover to the hinge (C).
C
4-26
B
LVPS/HVPS removal
1. Remove the rear door cover. See “Rear door and rear cover removal” on page 4-54.
2. Remove the left side cover. See “Left side cover removal” on page 4-23.
3. Place the printer on its top with the rear facing you.
Note: Be careful to not mar the finish of the printer.
4. Remove the two screws (A) from the right rear foot assembly.
A
5. Disconnect the fuser power cable (B).
B
Repair information
4-27
6. Remove the two screws (C) from the right rear foot, and the four screws (D) from the LVPS/HVPS shield.
D
C
7. Lift the LVPS/HVPS, and disconnect the three cables (E).
E
4-28
Note: Squeeze the clip to remove the cables from their connectors (F).
F
8. Disconnect the transfer roll cable (G).
G
9. Lift and remove the LVPS/HVPS.
Repair information
4-29
Main motor gear drive removal
1. Remove the left side cover. See “Left side cover removal” on page 4-23.
2. Disconnect the fuser link (A) from the front access door.
A
3. Place the printer on its right side.
Note: Be careful to not mar the finish of the printer.
4. Remove the four screws (B) from the main motor gear drive.
B
4-30
5. Lift the gear drive, and disconnect the main motor gear drive cable (C).
6. Remove the main motor gear drive.
Repair information
4-31
Manual feed clutch removal
1. Remove the left side cover. See “Left side cover removal” on page 4-23.
2. Open the front access door, and disconnect the fuser link (A).
A
3. Place the printer on its right side.
Note: Be careful to not mar the finish of the printer.
4. Remove the four screws (B) from the main motor gear drive.
B
5. Rotate the main motor gear drive enough to access the manual feed solenoid.
4-32
6. Use a screwdriver to remove the e-clip (C) from the manual feed clutch.
Note: The picture below shows the E260d, E260dn printer. The manual feed clutch removal is the same for all
models.
C
7. Remove the manual feed clutch (D).
D
Repair information
4-33
Manual feed solenoid removal
1. Remove the right side cover. See “Left side cover removal” on page 4-23.
2. Remove the duplex. See “Duplex removal” on page 4-11.
3. Open the front access door, and place the printer on its right side.
Note: Be careful to not mar the finish of the printer.
4. Remove the two screws (A).
Note: The picture below shows the E260d, E260dn printer. The manual feed solenoid removal is the same for
all models.
A
4-34
5. Remove the three screws (B) from the left door mount.
B
Repair information
4-35
6. Lift the left door mount (C) away from the side frame, and unroute the cable (D) with a spring hook.
7. Reinstall the left door mount, and place the printer on it’s top.
Note: Be careful to not mar the finish of the printer.
8. Disconnect the cable (D) from J25 on the controller board, and remove the manual feed solenoid.
Installation note:
Install the two screws holding the new solenoid in place, and route the cable (D) behind the MPF clutch (E).
D
4-36
E
C
Media ACM ASM feeder removal
1.
2.
3.
4.
5.
6.
Remove the left side cover. See “Left side cover removal” on page 4-23.
Remove the LVPS/HVPS. See “LVPS/HVPS removal” on page 4-27.
Remove the duplex. See “Duplex removal” on page 4-11.
Remove the main motor gear drive. See “Main motor gear drive removal” on page 4-30.
Remove the media feed clutch. See “Media feed clutch with cable removal” on page 4-40.
Use a screwdriver to pop the shaft retainer tab (A) loose from the ACM feed shaft.
7. Use a small pair of pliers to remove the shaft retainer tab.
Repair information
4-37
8. Use a screwdriver to pop the inner shaft lock (B) loose.
9. Remove the inner shaft lock (C).
4-38
10. Pull out the auto compensator shaft, and remove the spring (D).
11. Remove the auto compensator shaft.
12. Disconnect the spring (E) from the cylinder.
E
13. Remove the media ACM ASM feeder.
Repair information
4-39
Media feed clutch with cable removal
1. Remove the main motor gear drive. See “Main motor gear drive removal” on page 4-30.
2. Remove the duplex. See “Duplex removal” on page 4-11.
3. Disconnect the media feed clutch cable (A) from the controller board.
4. Unroute the cable from the bottom of the printer.
4-40
5. Remove the e-clip (B).
6. Remove the media feed clutch with cable (C).
Repair information
4-41
Media manual input sensor
1. Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
2. Place the machine on its top.
Note: Be careful to not mar the finish of the printer.
3. Disconnect the sensor cable (A) from J23 (MPFS) on the controller board.
A
4. Remove the screw (B).
B
5. Free the cable from its retainers, and pull it through the opening toward the sensor mount.
4-42
Re-installation note:
• Prop open the duplex door, and insert the hook end of the spring hook through the frame opening (C) from
the controller board side. Extend the hook until the sensor connector can be hooked.
• Hook the spring hook (D) to the connector (E), and pull it through the opening.
C
D
E
• Place the sensor into position, and reconnect the cable on the controller board.
• Using the spring hook, be sure to reroute the cable through the three retainers (F) between the sensor and
side frame.
F
Note: If the cable is not properly installed in its retainers, then the loose cable will obstruct the paper path.
Repair information
4-43
Warning: Check to make sure the duplex paper jam door is in its proper position. If it is not, then the paper tray
will become lodged and the printer will need to be replaced.
4-44
Multipurpose feeder (MPF) removal
1. Open the front access door.
2. Remove the four screws (A) from the upper front guide.
A
3. Remove the upper front guide.
4. Remove the two screws (B).
B
Repair information
4-45
5. Close the front access door, and pull up on the MPF by the steel shaft until the MPF lifts from its hinges.
Note: The picture below shows the E460dn, E460dw printer. The multipurpose feeder removal is the same for
all models.
6. Disconnect the MPF from the lower front cover.
4-46
7. Open the front access door, and remove the lower paper guide.
Repair information
4-47
Multipurpose feeder (MPF) feed clutch removal
1. Remove the left side cover. See “Left side cover removal” on page 4-23.
2. Remove the duplex. See “Duplex removal” on page 4-11.
3. Disconnect the cable (A) from the controller board.
4. Place the printer on its right side.
Note: Be careful to not damage any cables or mar the finish of the printer.
4-48
5. Remove the three screws (B) from the left side of the printer.
6. Disconnect the left hinge (C) from the feed clutch, and remove the e-clip (D).
7. Lift and remove the multipurpose feeder (MPF) feed clutch.
Repair information
4-49
Nameplate removal
1. Open the front access door.
2. Remove the three screws (A).
Note: The picture below shows the E260d, E260dn printer. The nameplate removal is the same for all models.
A
3. Remove the nameplate.
4-50
Operator panel removal
1. Remove the nameplate. See “Nameplate removal” on page 4-50.
2. Remove the bezel. See “Bezel removal” on page 4-5.
3. Remove the four screws (A) from the display plate.
4. Lift the operator panel cover, and disconnect the operator panel cable (B).
5. Remove the operator panel.
B
Repair information
4-51
Paper input and duplex sensor assembly removal
1. Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
2. Remove the duplex. See “Duplex removal” on page 4-11.
3. Remove the two screws (A) from the sensors.
A
4. Disconnect the sensor cable (B) from the controller board.
B
5. Remove the paper input and duplex sensor assembly.
4-52
Printhead removal
1. Remove the top cover. See “Top cover assembly removal” on page 4-61.
2. Remove the right side cover. See “Right side cover assembly removal” on page 4-58
3. Disconnect the two cables (A), and unroute them back through the frame toward the printhead.
A
4. Remove the three screws (B).
Note: Use a pencil to mark the screw locations of the printhead on the metal frame. Align the new printhead
relative to the location of the old printhead. See “Printhead assembly mechanical adjustment” on page 3-17.
B
5. Remove the printhead.
Repair information
4-53
Rear door and rear cover removal
1. Open the rear door.
2. Pull the rear door up at an angle, disconnect the door from the notch (A), and remove.
A
3. Remove the two screws (B) from the top of the rear cover.
B
4-54
4. Tilt the rear cover, and remove.
Repair information
4-55
Rear exit guide assembly with sensor and reversing solenoid removal
1. Remove the top cover. See “Top cover assembly removal” on page 4-61.
2. Remove the rear door and rear cover. See “Rear door and rear cover removal” on page 4-54.
3. Disconnect the narrow media sensor cable and the reversing solenoid cable (A).
4. Remove the six screws (B) from the rear exit guide assembly.
B
4-56
B
B
5. Remove the solenoid cable (C) through the opening.
6. Remove the narrow media sensor cable (D) through the opening.
7. Remove the rear exit guide assembly.
Note: Be careful to not damage the gears during the rear exit guide assembly removal and reinstallation.
Repair information
4-57
Right side cover assembly removal
Note: Leave the front cover closed when removing the right side cover assembly.
1. Remove the one screw (A) from behind the paper tray.
A
2. Remove the screw (B) from the bottom right side of the printer.
B
4-58
3. Press the latches (C).
C
4. Rotate the right side cover assembly out, and remove.
Repair information
4-59
Toner level sensor removal
1.
2.
3.
4.
Open the front access door.
Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
Disconnect the toner level sensor cable (A) from the controller board.
Squeeze the lower tabs (B) of the toner level sensor, and push it from its holder.
B
A
5. Remove the toner level sensor through the inside of the printer.
Note: The toner level sensor must be installed properly, or the printer will not function.
4-60
Top cover assembly removal
1.
2.
3.
4.
5.
Open the front access door.
Remove the left side cover. See “Left side cover removal” on page 4-23.
Remove the right side cover. See “Right side cover assembly removal” on page 4-58.
Remove the rear door and rear cover. See “Rear door and rear cover removal” on page 4-54.
Remove the two screws (A) from the left side of the printer.
6. Remove the two screws (B) from the right side of the printer.
Repair information
4-61
7. Lift the top cover, and remove.
Note:
• Be sure to lift the top cover assembly from the front to remove.
• During reinstallation, be sure the exit guide and the paper bin align correctly. A mismatch can cause paper
jams.
4-62
Transfer roll removal
Note: A flashlight may be useful to remove the transfer roll.
1. Open the front access door.
2. At the right side of the transfer roll, squeeze the holder arms (A) with the left hand while lifting. Stop when
the holder is unlatched.
3. At the left side of the transfer roll, squeeze the holder arms with the right hand while lifting with the left
hand. Stop when the left holder is unlatched.
4. With a hand at each end, lift the transfer roll out.
Note: Do not try removing the spring on the left; it is not removeable but can be dislodged. The spring included
with the FRU is to be used only if the old right-side spring is damaged or lost. Both springs must be positioned
on posts that cannot be seen. If the old springs are moved, then feel the base of the springs to assure that they
are on the posts. The top of the springs must be captured in the bearings of the transfer roll.
Repair information
4-63
Upper front guide assembly removal
1. Open the front access door.
2. Remove the four screws (A) from the upper front guide.
A
3. Remove the upper front guide.
4-64
Wear strip (tray 1 and 250-sheet tray 2) removal
1. Hold the tray with the bottom up.
2. Use a spring hook to disconnect the strip from the top of the tray.
3. Remove the strip from inside the tray.
Repair information
4-65
Wear strip (550-sheet tray 2) removal
1. Use a spring hook to disconnect the strip from the top of the tray.
2. Life the strip, and remove.
Note: When replacing the strip (for all trays):
• Carefully insert the strip from the top of the tray, and push it down through the opening until it snaps
into place.
• Turn the tray over to view the bottom of the strip. Using the spring hook, check to make sure that the
end of the strip is fastened tightly.
• Be sure that the drafted edge of the strip is installed toward the bottom of the tray.
4-66
5. Locations and connections
Locations
Front view
Front door
release
button
Operator
panel
Paper
stop
Front
door
Standard
output
bin
Manual
feeder
door
System
board
door
Standard 250-sheet tray (Tray 1)
Rear view
Rear
door
Ethernet
port
USB
port
Locking
device
Parallel
port
Printer power
cord socket
Power
switch
Locations and connections
5-1
Controller board connector pin values
5-2
Note: See the wiring diagram at back of book.
These values were measured with all connections made (plugged) or with only one connector at a time
unplugged to expose the pins. Always disconnect and connect with the printer power off. Otherwise, the values
below may not match.
Connector
J4
J5
J100
J7
Pin #
Value
cable plugged
1
Ground
2
1.7 V dc
3, 4
3.3 V dc
1, 3, 5, 6
3.3 V dc
2
5.0 V dc
4, 7
Ground
1
> 0 V dc
2, 3
5 V dc
4, 5, 6, 7
Ground
1
5 V dc (door closed)
Value
cable unplugged
(if different)
Comments
Cartridge
(The front access door must be closed.)
Operator panel
5 V dc
Printhead
Open door sensor
0 V dc (door open)
2
5 V dc
3
Ground
1, 10
5 V dc
9
2.9 V dc
J9
1
24 V dc
2
24 V dc
J10
1
2
J8
J11
J12
J13
J14
J17
J19
LSU
0 V dc
Cooling fan
24 V dc
24 V dc
Duplex solenoid
24 V dc
0 V dc
1
5 V dc
2
5 V dc
3
Ground
1
5 V dc
2
Ground
1
0.6 V dc
2
Ground
3
0 V dc
1
> 0 V dc
2
5 V dc
3
Ground
1, 4
0.1 V dc
2, 3, 6
5 V dc
5
Ground
7, 8, 9
24 V dc
Narrow media sensor
5 V dc
Thermistor
Toner level sensor
5 V dc
Fuser exit sensor
5 V dc
Main gear drive motor
USB port
Locations and connections
5-3
Connector
Pin #
Value
cable plugged
Value
cable unplugged
(if different)
J21
J23
Parallel port
1
1.1 V dc
2
5 V dc
3
Ground
J24
1
24 V dc
2
24 V dc
J25
1
24 V dc
2
24 V dc
J26
1
24 V dc
2
24 V dc
0 V dc
J27
1, 4
1.1 V dc
5 V dc
2, 5
5 V dc
3, 6
Ground
1, 4
3.3 V dc
2
24 V dc
6
Ground
1
5 V dc
3
1 V dc
4
Ground
5
5 V dc
J28
J501
J502
5-4
Comments
5 V dc
Manual feed sensor
MPF clutch
0 V dc
Manual feed solenoid
0 V dc
Media feed clutch
Input and duplex sensor
Tray 2
Toner patch (density) sensor
0 V dc
0V dc
1, 3, 5, 7, 11,
13, 15
5V dc
4
5 V dc
6
24 V dc
17, 19
24 V dc
Other
0 V dc
LVPS/HVPS
6. Preventive maintenance
This chapter describes procedures for printer preventive maintenance. Follow these recommendations to help
prevent problems and maintain optimum performance.
Safety inspection guide
The purpose of this inspection guide is to aid you in identifying unsafe conditions.
If any unsafe conditions exist, then find out how serious the hazard could be and if you can continue before you
correct the hazard.
Check the following items:
• Damaged, missing, or altered parts, especially in the area of the On/Off switch and the power supply
• Damaged, missing, or altered covers, especially in the area of the top cover and the power supply cover
• Possible safety exposure from any non-Dell attachments
Lubrication specifications
FRUs are typically lubricated as needed from the factory. If not, then lubricate only when parts are replaced or
as needed, not on a scheduled basis. Use of lubricants other than those specified can cause premature failure.
Some unauthorized lubricants may chemically attack parts. Use P/N 99A0394 (Nyogel 744) to lubricate
appropriate areas. Lubricate gears that were lubricated in the original part.
Preventive maintenance
6-1
6-2
7. Parts catalog
How to use this parts catalog
The following legend is used in the parts catalog:
AsmIndex
Part
number
Units/
mach
Units/
FRU
Description
• Asm-index: identifies the assembly and the item in the diagram. For example 3-1 indicates
•
•
•
•
•
•
assembly 3 and the item number 1.
Part number: identifies the unique number that identifies this FRU.
Units/mach: refers to the number of units actually used in the machine or product.
Units/FRU: refers to the number of units packaged together and identified by the part number.
NS: (Not shown) in the Asm-Index column indicates that the part is procurable but is not
pictured in the illustration.
PP: (Parts Packet) in the parts description column indicates the part is contained in a parts
packet.
Model information used in the parts catalog.
Machine type
and model
Description
4513-420
Dell 2330d
4513-430
Dell 2330dn
Parts catalog
7-1
Assembly 1: Covers
1
2
13
12
3
11
10
4
9
8
5
7
6
7-2
Assembly 1: Covers
AsmIndex
Part
number
Units/
mach
Units/
FRU
Description
1-1
40X5373
1
1
Top cover assembly
2
40X5377
1
1
Rear upper and lower cover assembly
3
40X5375
1
1
Right side cover
4
40X5398
1
1
Optional 250-sheet tray
4
40X5399
1
1
Optional 550-sheet tray
5
40X5394
1
1
250-sheet (Tray 2) assembly
5
40X5395
1
1
550-sheet (Tray 2) assembly
6
40X2855
1
4
Tray 2 wear strips (550-sheet tray only)
7
40X5382
1
6
Wear strips (250-sheet trays, optional and primary)
8
40X5381
1
1
Main tray
9
40X5379
1
1
Front door cover
10
40X5359
1
1
Nameplate cover
11
40X5378
1
1
Front access door assembly
12
40X5374
1
1
Left side cover
13
40X5355
1
1
LCD bezel cover, 2330d
13
40X5390
1
1
LCD bezel cover, 2330dn
Parts catalog
7-3
Assembly 2: Electronics
1
2
13
3
12
4
5
11
10
6
9
7
8
7-4
Assembly 2: Electronics
AsmIndex
Part
number
Units/
mach
Units/
FRU
Description
2-1
40X5354
1
LCD operator panel assembly, 2330d/2330dn
2
40X5344
1
Fuser assembly, 115 V
2
40X5345
1
Fuser assembly, 230 V
2
40X5346
1
3
40X5365
1
1
Duplex and media sensor assembly
4
40X5360
1
1
Access door open sensor assembly
5
40X5392
1
1
Cooling fan (screws included)
6
40X5385
1
1
Toner low sensor
7
40X5347
1
1
Controller board, 2330d
7
40X5349
1
1
Controller board, 2330dn
8
40X4361
1
LVPS/HVPS card assembly, 110 V/100 V
8
40X4362
1
LVPS/HVPS card assembly, 220 V
Fuser assembly, 100 V
9
40X5366
1
1
Manual input sensor assembly
10
40X5369
1
1
Manual feed solenoid
11
40X5371
1
1
MPF feed clutch
12
40X5370
1
1
Media feed (ACM) clutch
13
40X5387
1
LSU, 2330d/2330dn (printhead)
Parts catalog
7-5
Assembly 3: Frame
1
12
2
11
3
10
3
8
9
4
5
7
See instruction
sheet in the FRU.
7
7-6
6
Assembly 3: Frame
AsmIndex
3–1
Part
number
40X5364
Units/
mach
Units/
FRU
1
2
40X5372
1
3
40X5397
1
4
40X5396
N/A
Description
Transfer roll, bearings, gear, spring (CBM)
Media exit guide assembly (redrive)
1
Front mounts
Screws, miscellaneous
4
TP2NCX3X6PF-Ni
4
TP2C-4.0+8PF-Ni
4
M3.0*0.5+6PF-Ni
2
M3.0*0.5+4PF-Ni
2
M3.5*0.6+6P-Ni
5
40X5380
1
1
Complete duplex assembly
6
40X5453
1
1
Media (ACM) drive assembly
7
40X5451
2
2
Paper feed, ACM tires
7
40X5440
1
2
Tray 2 paper feed tires
8
40X5358
1
1
MPF tray assembly
9
40X5383
1
1
Upper front frame assembly
10
40X5368
1
1
Manual feed clutch CBM
11
40X5367
1
1
Main drive gearbox (in motor)
12
40X5363
1
1
NS
7470094
1
Duplex gear drive CBM
Field relocation package assembly
Parts catalog
7-7
Assembly 4: Options
AsmIndex
Part
number
Units/
mach
Units/
FRU
Description
NS
40X5972
1
1
Japanese font card assembly
NS
40X5970
1
1
Simplified Chinese font card assembly
NS
40X5971
1
1
Traditional Chinese font card assembly
NS
40X5969
1
1
Korean font card assembly
NS
40X5937
1
1
128MB DIMM
NS
40X5938
1
1
256MB DIMM
NS
40X5704
1
1
256MB flash
NS
40X1367
1
1
Parallel cable, packaged (3 m) (E460dn only)
NS
40X1368
1
1
USB cable, packaged (2 m)
7-8
Assembly 5: Power cords
AsmIndex
Part
number
Units/
mach
Units/
FRU
Description
NS
40X0297
1
Power cord, 1.8M (straight)—USA, Canada
NS
40X0278
1
Power cord, 6 foot (straight)—Europe and others
NS
40X0288
1
Power cord, 8 foot (straight)—Argentina
NS
40X0286
1
Power cord, 8 foot (straight)—United Kingdom
NS
40X0275
1
Power cord, 6 foot (straight)—Israel
NS
40X0274
1
Power cord, 6 foot (straight)—Switzerland
NS
40X0276
1
Power cord, 6 foot (straight)—South Africa
NS
40X0287
1
Power cord, 6 foot (straight)—Traditional Italy
NS
40X0279
1
Power cord, 6 foot (straight)—Denmark
NS
40X0277
1
Power cord, 6 foot (straight)—Brazil
NS
40X0282
1
Power cord, 1.8M (straight)—PRC
NS
40X0270
1
Power cord, 2.5M (straight)—Japan
NS
40X0280
1
Power cord, 1.8M (straight)—Korea
NS
40X0281
1
Power cord, 1.8M (straight)—Taiwan
NS
40X0296
1
Power cord, 1.8M (straight)—Australia
Parts catalog
7-9
7-10
Index
A
E
abbreviations 1-9
acronyms 1-9
Edge to Edge 3-13
EP Defaults 3-13
error log
clear log (diagnostics mode) 3-15
display log (diagnostics mode) 3-14
Print Log 3-15
error messages
service error codes 2-15
user attendance messages 2-6
ESD-sensitive parts 4-1
C
Charge Roll, diagnostics mode 3-14
compatibility 1-4
configuration ID 3-13
configuration menu
accessing 3-2
available menus 3-2
Demo Mode 3-4
Energy Conserve 3-4
Factory Defaults 3-4
Panel Menus 3-3
PPDS Emulation 3-3
configuration menu—
accessing 3-1
control panel 1-2
controller card
service check 2-22
F
fan
parts catalog 7-5
service check 2-23
frame, parts catalog 7-6
fuser
parts catalog 7-5
service check 2-25
Fuser Temp 3-13
D
G
defaults
factory defaults 3-4
diagnostic information 2-1
diagnostics mode 3-5
diagnostics mode— 3-1
EP Setup
Charge Roll 3-14
EP Defaults 3-13
Fuser Temp 3-13
Gap Adjust 3-14
Print Contrast 3-14
Transfer 3-13
Event Log
Clear Log 3-15
Display Log 3-14
Print Log 3-15
Hardware Tests
DRAM Test 3-8
Printer Setup
Configuration ID 3-13
Edge to Edge 3-13
Engine Settings 3-13
Model Name 3-13
Par S Strobe Adj 3-13
Registration 3-6
DRAM Test 3-8
Gap Adjust 3-14
H
handling ESD-sensitive parts 4-1
History
see error log 3-15
L
lithium battery 4-6
locations
front views 5-1
rear views 5-1
lubrication specifications 6-1
LVPS/HVPS
parts catalog 7-5
service check 2-25
M
messages
service error codes 2-15
user attendance messages 2-6
Model Name 3-13
models
comparison 1-1
diagrams 5-1
operator panels 1-2
service menus 3-1
trays available 1-5
Index
I-1
O
operator panel
LCD— 2-2
LED—
service check 2-27
overview 1-2
P
panel, control 1-2
paper jams
tips on preventing 1-7
parallel port service check 2-29
parts catalog
covers 7-2
electronics 7-4
frame 7-6
options 7-8
power-on self test (POST) 2-1
symptoms 2-20
Print Contrast 3-14
print media
preventing jams 1-7
trays by model 1-5
types and sizes 1-6
print quality pages
using 2-30
print quality problems
print media 1-7
service check 2-30
solving 2-34
printer symptom table 2-21
printhead
service check 2-37
R
registration 3-6
removals
covers
front access cover 4-6
procedures 4-2
S
safety information xiii
safety inspection guide 6-1
service checks 2-22
controller card 2-22
cooling fan 2-23
cover interlock switch 2-23
dead machine 2-24
fuser 2-25
LVPS/HVPS 2-25
main motor 2-26
operator panel 2-27
paper feed 2-27
paper jam during POST 2-27
paper never picks 2-28
paper picks but stops 2-27
paper picks sheets 2-28
paper trees, curls 2-29
I-2
parallel port 2-29
print quality 2-30
black page 2-31
blank page 2-30
heavy background 2-31
image density 2-32
light print 2-33
partial blank image 2-32
poor fusing of image 2-32
toner on back of page 2-33
white or black lines 2-33
printhead 2-37
transfer roll 2-37
service error codes 2-15
service menus 3-1
special tools 1-8
specifications
connectivity 1-4
input trays 1-5
memory 1-3
operating systems 1-4
photoconductor capacity 1-5
print media 1-6
toner capacity 1-5
start 2-1
strobe adjustment 3-13
symptom tables 2-20
POST 2-20
printer 2-21
T
tools 1-8
Top Margin 3-6
Transfer 3-13
transfer roll
parts catalog 7-7
service check 2-37
U
user attendance messages 2-6
Part number index
40X0270
40X0274
40X0275
40X0276
40X0277
40X0278
40X0279
40X0280
40X0281
40X0282
40X0286
40X0287
40X0288
40X0296
40X0297
40X1367
40X1368
40X2855
40X4361
40X4362
40X5344
40X5345
40X5346
40X5347
40X5349
40X5354
40X5355
40X5358
40X5359
40X5360
40X5363
40X5364
40X5365
40X5366
40X5367
40X5368
40X5369
40X5370
40X5371
40X5372
40X5373
40X5374
40X5375
40X5377
40X5378
40X5379
40X5380
40X5381
40X5382
40X5383
40X5385
40X5387
40X5390
40X5392
40X5394
Power cord, 1.77M (straight)—Japan - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot—Switzerland - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot (straight)—Israel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot—South Africa - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot (straight)—Brazil - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot (straight)—Europe and others - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot (straight)—Denmark - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 1.77M (straight)—Korea - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 1.77M (straight)—Taiwan - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 1.77M (straight)—PRC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot—United Kingdom - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot (straight)—Traditional Italy - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 6 foot—Argentina - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 1.8M (straight)—Australia - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Power cord, 1.77M (straight)—USA, Canada - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9
Parallel cable, packaged (3 m) (Dell 2330dn only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8
USB cable, packaged (2 m) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8
Tray 2 wear strips (550-sheet tray only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
LVPS/HVPS card assembly, 110 V/100 V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
LVPS/HVPS card assembly, 220 V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Fuser assembly, 115 V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Fuser assembly, 230 V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Fuser assembly, 100 V - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Controller board, 2330d - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Controller board, 2330dn - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
LCD operator panel assembly, Dell 2330d/2330dn - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
LCD bezel cover, Dell 2330d - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
MPF tray assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Nameplate cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Access door open sensor assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Duplex gear drive CBM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Transfer roll, bearings, gear, spring (CBM) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Duplex and media sensor assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Manual input sensor assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Main drive gearbox (in motor) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Manual feed clutch CBM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Manual feed solenoid - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Media feed (ACM) clutch - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
MPF feed clutch - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Media exit guide assembly (redrive) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Top cover assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Left side cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Right side cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Rear upper and lower cover assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Front access door assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Front door cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Complete duplex assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Main tray - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Wear strips (250-sheet trays, optional and primary) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Upper front frame assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
Toner low sensor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
LSU, Dell 2330d/2330dn (printhead) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
LCD bezel cover, Dell 2330dn - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Cooling fan (screws included) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
Tray 2 assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
Part number index
I-3
40X5395
40X5396
40X5397
40X5398
40X5399
40X5440
40X5451
40X5453
40X5704
40X5937
40X5938
40X5969
40X5970
40X5971
40X5972
7470094
550-sheet (Tray 2) assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Screws, miscellaneous - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Front mounts - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Optional 250-sheet tray - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Optional 550-sheet tray - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Tray 2 paper feed tires - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Paper feed, ACM tires - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Media (ACM) drive assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 256MB flash - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 128MB DIMM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 256MB DIMM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Korean font card assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Simplified Chinese font card assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Traditional Chinese font card assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Japanese font card assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Field relocation package assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
I-4 Part number index
7-3
7-7
7-7
7-3
7-3
7-7
7-7
7-7
7-8
7-8
7-8
7-8
7-8
7-8
7-8
7-7
Dell 2330d/2330dn - recommended spare part list
04 Feb 2010
MFG P/N
MFG Part Description
FUSER AND ACCESSORIES
DRU0196
110V FUSER ASM
DRU0217
100V FUSER ASM
DRU0197
220V FUSER ASM
TONER / INK
00PK492
2K Use and Return Cartridge
00PK941
6K Use and Return Cartridge
00DM254
2K Regular Cartridge
00PK937
6k Regular Cartridge
FEEDER, TRAY AND TRAY HOUSING
DRU0204
PRIMARY MEDIA TRAY ASM
DRU0205
OPTIONAL (W/O TRAY) DRAWER ASM
DRU0206
OPTIONAL (W/O DWR) TRAY ASM
DRUM
24B3422
Imaging Drum Kit
BASE UNIT
DRU0221
EXCH CAN/LA 110V BASE PRNTR ASM
DRU0222
EXCH CAN/LA 110V NW PRNTR ASM
DRU0225
EXCH 110V BASE PRNTR ASM
Dell P/N
Dell Part Description
CRU or
FRU
N821D
C997J
R714D
ASSEMBLY, FUSER, 110V, PRINTER/PRINTER ACCESSORIES, 2330
ASSEMBLY, FUSER, 100V, PRINTER/PRINTER ACCESSORIES, 2330
ASSEMBLY, FUSER, 220V, PRINTER/PRINTER ACCESSORIES, 2330
FRU
FRU
FRU
PK492
PK941
DM254
PK937
CARTRIDGE, TONER, 2K, USE/RETURN, 2330
CARTRIDGE, TONER, 6K, USE/RETURN, 2330
CARTRIDGE, TONER, 2K, REGLR, 2330
CARTRIDGE, TONER, 6K, REGLR, 2330
CRU
CRU
CRU
CRU
P646D
R511D
DP304
TRAY, PAPER, ASSEMBLY, PRIMARY, 2330 (with Instruction sheet)
DRAWER, PAPER, 550SHT, 2330 (w/o Tray)
TRAY,PAPER,550SHT,2330
CRU
CRU
CRU
PK496
CARTRIDGE, DRUM, 30K, PHOTO CONDUCTOR, 2330
CRU
UU830
RR260
UU826
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, ICON, 2330D
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, ICON, 2330DN
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, UNITED STATES,
2330D
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, UNITED STATES,
2330DN
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, JAPAN/JAPANESE,
2330D
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, JAPAN/JAPANESE,
2330DN
ASSEMBLY, Base, SERVICE KIT, HIGH VOLTAGE, ICON, 2330D
ASSEMBLY, Base, SERVICE KIT, HIGH VOLTAGE, ICON, 2330DN
ASSEMBLY, Base, SERVICE KIT, LOW VOLTAGE, TRADE AGREEMENT
ACT, 2330DN
ASSEMBLY, Base, SERVICE KIT, HIGH VOLTAGE, TRADE AGREEMENT
ACT, 2330DN
ASSEMBLY, Base, SERVICE KIT, HIGH VOLTAGE, CHINA CUSTOMER
CENTER, 2330D
ASSEMBLY, Base, SERVICE KIT, HIGH VOLTAGE, CHINA CUSTOMER
CENTER, 2330DN
CRU
CRU
CRU
YY498
CABLE, USB, 10FT, PRINTER/PRINTER ACCESSORIES
CRU
GH686
PRINTER/PRINTER ACCESSORIES, CABLE, IEEE-1284, LT, PARALLEL,
BLACK
CRU
M727D
P637D
Controller base card assembly
Controller network card assembly
FRU
FRU
UU697
KIT, DOCUMENTATON ON FLOPPY DISK, CAN-LTN,
ENGLISH,FRENCH,SPANISH, 2330
KIT, DOCUMENTATON ON FLOPPY DISK, ASIA PACIFIC COUNTRIES
AND JAPAN, ENGLISH/JAPANESE/SIMPLE CHINESE, 2330
CRU
KIT, DOCUMENTATON ON FLOPPY DISK, EUROPE, MIDDLE EAST &
AFRICA, 2330
KIT, DOCUMENTATON ON FLOPPY DISK, UNITED STATES, ENG-SPN,
2330
KIT, DOCUMENTATON ON FLOPPY DISK, TAA-LV, 2330DN
KIT, DOCUMENTATON ON FLOPPY DISK,
ENGLISH,FRENCH,SPANISH, TAA-HV, 2330DN
CRU
DRU0226
EXCH 110V NW PRNTR ASM
RR254
DRU0223
EXCH 100V BASE PRNTR ASM
PK560
DRU0224
EXCH 100V NW PRNTR ASM
DX866
DRU0227
DRU0228
DRU0229
EXCH 220V BASE PRNTR ASM
EXCH 220V NW PRNTR ASM
EXCH TAA/GSA 110V NW PRNTR ASM
PK558
DX860
GT082
DRU0230
EXCH TAA/GSA 220V NW PRNTR ASM
GT088
DRU0231
EXCH SANBAO BASE PRNTR ASM
MX480
DRU0232
EXCH SANBAO NW PRNTR ASM
MX472
CABLES AND POWER CORDS
CA1004020213910
CABLE, USB, 10FT, PRINTER/PRINTER
ACCESSORIES
CD25C06L36-C38-DF
PTR,CBL,IEEE-1284,LT,PRL,BLK
ELECTRICAL / ELECTRONICS BOARDS AND CARDS
DRU0199
CONTROLLER NNW CARD ASM
DRU0200
CONTROLLER NW CARD ASM
DOCUMENTATION, DRIVERS AND APPLICATIONS
3016093
EFS CA/LA Pubs Kit
CRU
CRU
CRU
CRU
CRU
CRU
CRU
CRU
CRU
3016091
EJSC APJ Pubs Kit
RR232
3016094
EFIGS,D EMEA Pub Kit
RR252
3016092
Eng - Spain Pub Kit
WX018
3016095
3016096
EFS TAA 110V Pub Kit
EFS TAA 220V pub Kit
JN400
UU815
PRINT MEDIA
DRU0198
LSU PRTHD ASM
T371D
PRINTHEAD, LASER SCANNING UNIT, PRINTER/PRINTER
ACCESSORIES, 2330
FRU
KIT, PTR, MEM, 128MB, SDRAM-DIMM
KIT, PTR, MEM, 256MB, SDRAM-DIMM
H963K
J793K
KIT, PTR, MEM, 128MB, SDRAM-DIMM
KIT, PTR, MEM, 256MB, SDRAM-DIMM
CRU
CRU
TOP COVER ASM
R716D
COVER, TOP, ASSEMBLY, PRINTER/PRINTER ACCESSORIES, 2330
FRU
MEMORY
1022330
1022331
PLASTICS
DRU0212
CRU
CRU
CRU
CRU
DRU0218
MPF COVER
N823D
COVER, MULTIPURPOSE FEEDER, PRINTER/PRINTER ACCESSORIES,
2330
ASSY,DOOR,FRONT,LATCH,PTR,2330
COVER, REAR, PRINTER/PRINTER ACCESSORIES, 2330
COVER, RIGHT, PRINTER/PRINTER ACCESSORIES, 2330
COVER, LEFT, PRINTER/PRINTER ACCESSORIES, 2330
ASSEMBLY, Card, CONTROL PANEL, SBCS, 2330
ASSEMBLY, Card, CONTROL PANEL, DOUBLE BYTE CHARACTER
STRING, 2330
ASSY,CRD,CNTL PNL,ICON,2330
COVER, FRONT-TRIM-RING, Base, 2330
COVER, FRONT-TRIM-RING, NTWK, 2330
COVER, MEM-ACCESS-DOOR, PRINTER/PRINTER ACCESSORIES,
2330
DRU0235
DRU0215
DRU0214
DRU0213
DRU0201
DRU0208
Front Access door/Latch Asm.
REAR UPPR AND LWR COVER CBM
RIGHT COVER
LEFT COVER ASM
OP PANEL ASM
OP PANEL ASM (DBCS)
H226J
P657D
P639D
M729D
T362D
F453J
DRU0233
DRU0210
DRU0211
DRU0234
OP PANEL ASM (ICON ONLY)
FRONT NAME PLATE COVER RING (BASE)
FRONT NAME PLATE COVER RING (NW)
Memory Access door
Y857J
T364D
D693J
R719D
POWER SOURCES
DRU0202
LVPS/HVPS 110V CARD ASM
M733D
PWA, POWER DISTRIBUTION BOARD, 100V-110V,
PRINTER/PRINTER ACCESSORIES, 2330
FRU
DRU0203
LVPS/HVPS 220V CARD ASM
N826D
PWA, POWER DISTRIBUTION BOARD, 220V, PRINTER/PRINTER
ACCESSORIES, 2330
FRU
MISCELLANOUS HARDWARE
DRC0325
COOLING (2 WIRE) FAN
DRC0324
ROLL CBM TRANSFER
DRU0207
ACM TIRE PAPER FEED
DRC0326
TONER LEVEL RO SENSOR
DRC0327
ACCESS COVER OPEN SENSOR ASM
DRU0219
TRAY2 ACM TIRE
H317J
N828D
T376D
P649D
T375D
N845D
FAN, COOLING, 2WIRE, 24V, PRINTER/PRINTER ACCESSORIES, 2330
ROLLER, TRANSFER, PRINTER/PRINTER ACCESSORIES, 2330
ROLLER, PK-ARM, 2TIRES, PRINTER/PRINTER ACCESSORIES, 2330
SENSOR, CARTRIDGE, TONER, CBL-NO, 2330
SNSR,CVR-ACCESS,ASSY,PTR,2330
ROLLER, PK-ARM, 550-TRAY, PRINTER/PRINTER ACCESSORIES, 2330
(with Instruction sheet)
FRU
FRU
CRU
FRU
FRU
CRU
DRU0209
DRU0220
MFP TRAY ASSM.
LEGAL EXTENDER COVER
R730D
P651D
TRAY, PAPER, ASSEMBLY, MULTIPURPOSE FEEDER, 2330
COVER, EXTENDER, LGL-PAPER, PRINTER/PRINTER ACCESSORIES,
2330 (with Instruction sheet)
FRU
CRU
DRC0328
DRC0329
DRC0330
DRC0331
DRC0332
Clutch Manual Feed
Clutch Media Feed (ACM)
Sensor DPLX/Paper Input Asm
Sensor Manual Input Asm
Redrive Exit Guide w/sensor
N382M
N383M
M663M
M664M
P329M
CLCH,FDR,MNL,PTR,LS,2330
CLCH,FDR,MEDIA,PTR,LS,2330
ASSY,SNSR,PAPER,INPUT,PTR,2330
ASSY,SNSR,MNL,INPUT,PTR,2330
GDE,EXIT,REDR,SNSR,PTR,2330
FRU
FRU
FRU
FRU
FRU
Notes
CRU : Customer Replaceable Units - refers to parts that can easily be replaced by the customer without sending an onsite technician.
FRU : Field Replaceable Unit - a part that can be replaced or added by onsite technician.
FRU
FRU
FRU
CRU
FRU
FRU
FRU
FRU
FRU
FRU
FRU
Download PDF

advertising