Service manual | Epson COLOR 300 Printer User Manual

Service
This manual is to be used by qualified appliance
technicians only. Maytag does not assume any
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person.
2006
Over-the-Range
Domestic
Microwaves
This Base Manual covers general information
Refer to individual Technical Sheet
for information on specific models
This manual includes, but is
not limited to the following:
UMV1152CA*
AMV1154BA*
AMV5164BA*
AMV5164BC*
AMV5206BA*
AMV6167BD*
MMV1153BA*
MMV4205BA*
MMV5165BA*
MMV5207BA*
MMV5207BC*
JMV8166BA*
JMV8208BA*
JMV8208BC*
JMV9169BA*
16027303
June 2006
Replaces 16027128
Important Information
Pride and workmanship go into every product to provide our customers with quality products. It is possible, however,
that during its lifetime a product may require service. Products should be serviced only by a qualified service
technician who is familiar with the safety procedures required in the repair and who is equipped with the proper tools,
parts, testing instruments and the appropriate service manual. REVIEW ALL SERVICE INFORMATION IN THE
APPROPRIATE SERVICE MANUAL BEFORE BEGINNING REPAIRS.
Important Notices for Consumers and Servicers
!
WARNING
To avoid risk of serious injury or death, repairs should not be attempted by an unauthorized service personnel,
dangerous conditions (such as exposure to electrical shock) may result.
!
CAUTION
Maytag will not be responsible for any injury or property damage from improper service procedures. If performing
service on your own product, assume responsibility for any personal injury or property damage which may result.
To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this
product. For further assistance, please contact:
Customer Service Support Center
CAIR Center
Web Site
Telephone Number
WWW.AMANA.COM ................................................ 1-800-843-0304
WWW.MAYTAG.COM ............................................. 1-800-688-9900
WWW.JENNAIR.COM ............................................. 1-800-536-6247
CAIR Center in Canada ........................................... 1-800-688-2002
Amana Canada Product ........................................... 1-866-587-2002
Recognize Safety Symbols, Words, and Labels
! DANGER
DANGER—Immediate hazards which WILL result in severe personal injury or death.
!
WARNING
WARNING—Hazards or unsafe practices which COULD result in severe personal injury or death.
!
CAUTION
CAUTION—Hazards or unsafe practices which COULD result in minor personal injury or product or property
damage.
2
16027303
© 2006 Maytag Services
Table of Contents
Important Information ................................................... 2
Important Safety Information ........................................ 4
Microwave Leakage Testing .......................................... 5
General Information
Specifications ............................................................ 7
Placement of the Oven ............................................... 7
Location of Model Number ......................................... 7
Model Identification .................................................... 7
Service ....................................................................... 7
Parts and Accessories ............................................... 7
Asure™ Extended Service Plan ................................. 7
Radio Interference ...................................................... 7
Electrical Requirements ............................................. 8
Cleaning ..................................................................... 8
Grounding Instructions ............................................... 8
Microwave Oven Description ...................................... 9
Troubleshooting Procedures
Troubleshooting Table .............................................. 10
Checkout Procedure: Fuse ..................................... 11
Error Code Table ..................................................... 12
Testing Procedures
Component Testing Procedures ............................... 13
Control Panel Sensor Test ....................................... 16
Power Test (Traditional Test Method) ....................... 17
Traditional Power Test Temperature Chart ............... 17
Touch Pads/Control Panel
Switch Membrane Pinouts ............................ 18 - 30
© 2006 Maytag Services
Disassembly Procedures
Grille Removal .......................................................... 31
Door Assembly Removal .......................................... 31
Door Disassembly ................................................... 31
Control Panel Removal ............................................ 32
Printed Circuit Board Removal ................................ 32
Control Key Panel Removal ..................................... 33
Outer Case Removal ................................................ 33
Stirrer Assembly Removal ........................................ 33
Interlock Door Latch Switches Removal .................. 34
High Voltage Capacitor Removal .............................. 35
Diode Removal ........................................................ 35
Transformer Removal .............................................. 35
Replacing Fuse ....................................................... 35
Magnetron Removal ................................................. 35
Magnetron Fan Assembly Removal .......................... 36
Magnetron Thermal Fuse Removal ........................... 36
Humidity Sensor Removal (Select Models) .............. 36
Oven Thermostat Removal ....................................... 36
Turntable Motor Removal ......................................... 37
Vent Blower Removal ............................................... 37
Convection Motor and Heater Element Removal
(Select Models) ................................................... 38
Convection Heater Element Removal
(Select Models) ................................................... 38
Light Socket Removal .............................................. 38
Grille Heater Element Removal (Select Models) ....... 38
Appendix A
Installation Instructions ........................................... A-2
Appendix B
Use and Care information ........................................ B-2
16027303
3
3
Important Safety Information
!
CAUTION
Read the following information to avoid possible exposure to microwave radiation:
The basic design of the Maytag and Amana microwave
oven makes it an inherently safe device to both use and
service. However, there are some precautions which
should be followed when servicing the microwave oven to
maintain this safety. These are as follows:
1. Always operate the unit from an adequately grounded
outlet. Do not operate on a two-wire extension cord.
2. Before servicing the unit (if unit is operable), perform
the microwave leakage test.
3. The oven should never be operated if the door does
not fit properly against the seal, the hinges or hinge
bearings are damaged or broken; the choke is
damaged, (pieces missing, etc.); or any other visible
damage can be noted. Check the choke area to
ensure that this area is clean and free of all foreign
matter.
4. If the oven operates with the door open and
produces microwave energy, take the following
steps.
A. Tell the user not to operate the oven.
B. Contact Maytag immediately.
5. Always have the oven disconnected when the outer
case is removed except when making the "live" tests
called for in the Service Manual. Do not reach into the
equipment area while the unit is energized. Make all
connections for the test and check them for tightness
before plugging the cord into the outlet.
6. Always ground the capacitors on the magnetron filter
box and H. V. Capacitor with an insulated-handle
screwdriver before working in the high voltage area
of the equipment compartment. Some types of
failures will leave a charge in these capacitors and
the discharge could cause a reflex action which
could make you injure yourself.
4
7. In the area of the transformer, capacitor, diode, and
magnetron there is HIGH VOLTAGE. When the unit is
operating, keep this area clean and free of anything
which could possibly cause an arc or ground, etc.
8. Do not for any reason defeat the interlock switches.
There is no valid reason for this action at any time;
nor will it be condoned by Maytag.
9. IMPORTANT: Before returning a microwave to a
customer, check for proper switch interlock action.
The primary and secondary switches MUST open
when the door is actuated. The monitor switch MUST
close at a 1/4 inch when the door is opened.
10.Before returning a microwave to a customer, verify
the door spacing is reasonably uniform along the
top, bottom, and sides, and that it measures 1/8 inch
or less.
11. The microwave oven should never be operated with:
• Any components removed and/or bypassed.
• Any of the safety interlocks failing.
• Any of the seal surfaces failing, missing, or
damaged.
12.To ensure that the unit does not emit excessive
microwave leakage and to meet the Department of
Health Human Service guidelines, check the oven
for microwave leakage using Narda Model 8100,
8200, Holaday HI1500, HI1501 or Simpson 380M
leakage monitor as outlined in the instructions. The
maximum leakage level allowed is 4mW/cm2.
13. If servicer encounters an emission reading over
4 mW/cm2 the servicer must cease repair and
contact the Maytag Service Department immediately
for further direction. Maytag will contact the proper
Government Agency upon verification of the test
results.
16027303
© 2006 Maytag Services
Microwave Leakage Testing
!
Measurement With the Outer Panel
Removed
W ARNING
Check for radiation leakage after servicing. Should the
leakage be more than 4mW/cm2 inform Maytag
immediately. After repairing or replacing any radiation
safety device, keep a written record for future
reference, as required by D.H.H.S. and HEW
regulations. This requirement must be strictly
observed. In addition, the leakage reading must be
recorded on the service repair ticket while in the
customer’s home.
Avoid contacting any high voltage components.
Whenever you replace the magnetron, measure for
radiation leakage before the outer panel is installed and
after all necessary components are replaced or
adjusted. Special care should be taken in measuring
around the magnetron.
Equipment
Measurement With a Fully Assembled Oven
• Electromagnetic radiation monitor
• 600 cc glass beaker
After all components including the outer panel are fully
assembled, measure for radiation leakage around the
door periphery, the door viewing window, the exhaust
opening, and air inlet openings.
Procedure For Measuring Radiation
Leakage
Note before measuring • Do not exceed meter full scale deflection. Leak
monitor should initially be set to the highest scale.
• To prevent false readings the test probe should be
held by the grip portion of the handle only.
• The scan speed is equal to one inch per antenna
revolution or one inch per second if antenna speed is
unknown.
• Areas to be checked are all door seal areas and any
venting parts.
• Leakage with the outer panel removed...4mW/cm2 or
less.
• Leakage for fully assembled oven with door normally
closed ...4mW/cm2 or less.
• Leakage for a fully assembled oven (before the latch
switch (primary) is interrupted) while pulling the door ...
4mW/cm2 or less.
1 . Pour 275 ±15 cc (9 oz ±1/2 oz) of 20 ± 5°C
(68 ± 9°F) water in a beaker which is graduated to
600 cc and place the beaker in the center of oven.
2. Set the radiation monitor to 2450 MHz and use it
following the manufacturer’s recommended test
procedure to assure correct results.
3. While measuring the leakage, always use the two
inch (5 cm) spacer supplied with the probe.
4. Press the start pad or turn on the timer and with the
magnetron oscillating, measure the leakage by
holding the probe perpendicular to the surface being
measured.
© 2006 Maytag Services
Record Keeping and Notification After
Measurement
1. After any adjustment or repair to a microwave oven,
a leakage reading must be taken. Record this
leakage reading on the repair ticket even if it is zero.
2. A copy of the repair ticket and the microwave
leakage reading should be kept by the repair facility.
16027303
5
General Information
This manual provides basic instructions and suggestions
for handling, installing , and servicing microwave ovens.
The directions, information, and warnings in this manual
are developed from experience with, and careful testing of
the product. If the unit is installed according to the
Installation Instructions, it will operate properly and will
require minimal servicing. A unit in proper operating order
ensures the consumer all the benefits provided by efficient
microwave cooking.
This manual contains information needed by authorized
service technicians to install and service the microwave
pertaining to this manual. There maybe, however some
information which needs further explanation. Refer to
individual Installation Instructions, Use and Care,
Technical Sheets, or toll free technical support line to
answer questions from authorized service technicians.
Cooking Nomenclature
A
M
V
6
1
6
7
B
D
W
Color
A
B
C
H
L
P
Q
S
T
W
F
N
Brand
A
C
G
Amana
Magic Chef
Graffer &
Sattler
Hardwick
Jenn-Air
Maytag
Norge
Universal
Crosley
H
J
M
N
U
Y
Listing
Fuel
B
D
E/J
G
L
M
P
X
W
Almond on Almond
Black
Brushed Chrome
Traditional White
Traditional Almond
Prostyle
Monochromatic Bisque
Stainless
Traditional Bisque
White on White
Frost White (True Color White)
Natural Bisque (True Color Bisque)
A
C
D
G
M
P
Butane
Dual Fuel
Electric
Gas, Natural
Liquid Propane
Microwave
Standing Pilot
No Fuel
Warming Drawer
X
UL/AGA
CSA/CGA/CUL
Dual Listed
220-240 V / 50-60 Hz
Military Model
PSB Approved
(Singapore)
Export 120 V / 60 Hz
Production Code
This identifies the
production version.
Product Type
A
C
D
E
G
L
M
P
Q
R
S
T
V
W
Y
Z
6
Accessory/Cartridge
Cooktop Updraft/Countertop
Downdraft Cooktop or Warming Drawer
Eyelevel Range
Grill
Range (20")
Range (36")
Drop In (24")
Wall Oven (27")
Range, Free-Standing (30")
Slide-In (30")
Range Hood
OTR
Wall Oven
RV Range
RV Top
Feature Content
1000-3999
4000-6999
7000-9999
16027303
Brands
Maytag/Amana
Jenn Air
© 2006 Maytag Services
General Information
Specifications
Service
Refer to individual Technical Sheet for specification
information.
Placement of the Oven
This microwave can be easily placed in the kitchen, family
room, or anywhere else in the house. Place the oven on a
flat surface such as a kitchen countertop or a specially
designed microwave oven cart. Do not place oven above a
gas or electric range. Free air flow around the oven is
important.
Do Not Block Air Vents
All air vents must be kept clear during cooking. If air vents
are covered during operation the oven may overheat. In
this case, a sensitive thermal safety device automatically
turns the oven off. The oven will be inoperable until the
oven has cooled sufficiently.
Location of Model Number
To request service information or replacement parts, the
service center will require the complete model, serial, and
manufacturing number of your microwave oven. The
number is located inside the oven door cavity as shown in
the illustration below.
Keep a copy of sales receipt for future reference or in
case warranty service is required. To locate an authorized
servicer:
• For Amana product call 1-800-628-5782 or visit the
Web Site at www.amana.com
• For Maytag/Jenn-Air product call 1-800-462-9824 or
visit the Web Sites at www.maytag.com or
www.jennair.com
• For product in Canada call 1-866-587-2002 or visit the
Web Sites at www.amana.com, www.maytag.com or
www.jennair.com
Warranty service must be performed by an authorized
servicer. We also recommend contacting an authorized
servicer, if service is required after warranty expires.
Parts and Accessories
Purchase replacement parts and accessories over the
phone. To order accessories for your product call:
• For Amana product call 1-877-232-6771 or visit the
Web Site at www.amana.com
• For Maytag/Jenn-Air product call 1-800-462-9824 or
visit the Web Sites at www.maytag.com or
www.jennair.com
• For product in Canada call 1-866-587-2002 or visit the
Web Sites at www.amana.com, www.maytag.com or
www.jennair.com
Extended Service Plan
Model Identification
Complete enclosed registration card and promptly return.
If registration card is missing:
• For Amana product call 1-800-843-0304 or visit the
Web Site at www.amana.com
• For Maytag product call 1-800-688-9900 or visit the
Web Site at www.maytag.com
• For Jenn-Air product call 1-800-536-6247 or visit the
Web Site at www.jennair.com
• For product in Canada call 1-866-587-2002 or visit the
Web Sites at www.amana.com, www.maytag.com or
www.jennair.com
When contacting provide product information located on
rating plate.
Record the following:
Model Number:
___________________
Manufacturing Number:
___________________
Serial or S/N Number:
___________________
Date of purchase:
___________________
Dealer’s name and address:
___________________
© 2006 Maytag Services
We offer long-term service protection for this new oven.
• Asure™ Extended Service Plan is specially designed
to supplement Amana’s strong warranty. This plan
covers parts, labor, and travel charges.
Call 1-866-232-6244 for information.
• Dependability Plus™ Extended Service Plan is
specially designed to supplement Maytag’s and JennAir’s strong warranty. This plan covers parts, labor, and
travel charges.
Call 1-800-925-2020 for information.
Radio Interference
1. Microwave oven operation may interfere with the radio
or TV reception.
2. When there is interference, it may be reduced or
eliminated by taking the following measures:
• Clean the door and the seal surface of the oven.
• Reorient the receiving antenna of the radio or TV.
• Relocate the microwave oven in relation to the radio
or TV.
• Move the microwave away from the receiver.
• Plug the microwave into a different outlet so that the
microwave and receiver are on different branch
circuits.
3. 120 VAC, 60 Hz household outlet. Be sure the circuit
is at least 15 or 20 A and the microwave oven is the
only appliance on the circuit. It is not designed for 50
Hz or any circuit other than a 120 VAC, 60 Hz circuit.
• Electrical Rating of the Oven: 120 VAC, 60 Hz.
16027303
7
General Information
Electrical Requirements
Grounding Instructions
The oven is designed to operate on a Standard 120 VAC,
60 HZ household outlet.
This appliance must be grounded. If an electrical short
circuit occurs, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
The cord for this appliance has a grounding wire with a
grounding plug. Put the plug into an outlet that is properly
installed and grounded.
Cleaning
Before cleaning the oven, unplug the power supply cord. If
impossible, open the oven door to prevent an accidental
oven start.
Inside of the Oven
Use a damp cloth to wipe out crumbs and spillovers. It is
important to keep the area between door and cavity front
clean to assure a tight seal. Remove greasy spatters with
a sudsy cloth, then rinse and dry. Do not use harsh
detergent or abrasive cleaners.
Glass Tray
The glass tray can be washed by hand or in the
dishwasher.
!
To avoid risk of electric shock, personal injury or death,
use grounding plug properly.
Ask a qualified electrician if you do not understand the
grounding instructions or if you wonder whether the
appliance is properly grounded.
Keep the electrical power cord dry and do not pinch or
crush it in any way.
Control Panel
Wipe with a damp cloth followed immediately by a dry
cloth. The Child Lock feature is also useful when cleaning
the control panel. Child Lock prevents accidental
programming when wiping the control panel
(if so equipped).
Properly Polarized and
Grounded Outlet
Door
If steam accumulates inside or around the outside of the
oven door, wipe the panel with a soft cloth. This may
occur when the microwave oven is operated under high
humidity conditions and in no way indicates a malfunction
of the unit.
Outside Oven Surface
Clean with damp cloth. To prevent damage to the
operating parts inside the oven, the water should not be
allowed to seep into the ventilation openings.
After cleaning the oven, be sure that the rotating ring and
the glass tray are in the right position. Press the STOP/
CLEAR pad twice to reset any accidental key setting.
8
W ARNING
Three-Pronged (Grounding) Plug
For a permanently connected appliance: This appliance
must be connected to a grounded, metallic, permanent
wiring system, or an equipment grounding conductor
should be run with the circuit conductors and connected
to the equipment grounding terminal or lead on the
appliance.
16027303
© 2006 Maytag Services
General Information
Microwave Oven Description
© 2006 Maytag Services
16027303
9
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to microwave oven and discharge the
high-voltage capacitor before servicing, unless testing requires power.
! CAUTION
•
•
•
•
•
Verify proper grounding before checking for trouble.
Be careful of the high voltage circuit.
Discharge the high voltage capacitor.
When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire from
these parts and then check continuity with the AC plug removed. To do otherwise may result in a false reading
or damage to your meter.
Do not touch any part of the circuit on the printed circuit board, since static electric discharge may damage the
control panel. Always touch yourself to ground while working on this panel to discharge any static charge built
up in your body.
Troubleshooting Table
Symptom
Microwave oven does not work, no
display, fuse is OK.
Cause
Correction
If thermal (magnetron) cutout is
1. Open or loose wire harness.
defective, check fan motor.
2. Open thermal (magnetron) cutout.
If low voltage transformer is
3. Open low voltage transformer.
defective, check PCB assembly.
4. Defective PCB assembly.
Microwave oven does not work, no 1. Open or loose wire harness.
Check adjustment of primary,
2. Defective primary latch switch.*
display, fuse is blown.
interlock monitor and door
3. Defective monitor switch.*
sensing switches.
4. Shorted high voltage capacitor.*
Check power relay.
5. Shorted high voltage transformer.*
*NOTES: If any primary, interlock monitor or door sensing switches are defective, replace all at the same time.
If power relay contacts measure continuity, replace also.
If high voltage transformer is replaced, check diode and magnetron also.
Refer to operation instructions.
Microwave oven does not accept
1. Key input is not in-sequence.
Check connection between key
key input (touch pad input).
2. Open or loose connection between
pad and PCB assembly.
key pad and PCB assembly.
Replace key pad membrane.
3. Shorted or open key pad.
Replace PCB assembly.
4. Defective PCB assembly.
Adjust latch switches.
Microwave oven timer operational, 1. Latch switches not aligned.
2. High voltage circuit loose connection Check connections to high
but microwave does not oscillate
voltage circuits (magnetron).
(magnetron filament circuit).
(rotate).
Check transformer, capacitor,
3. Defective high voltage components.
diode and magnetron fuse.
4. Power relay wiring open or loose.
Check power relay wiring.
5. Primary latch switch defective.
Replace power relay or PCB
6. Power relay or PCB assembly
assembly.
defective.
Microwave oven lamp and fan
1. Primary latch switch misadjusted or
Adjust door and latch switches.
motor activate.
loose.
2. Primary latch switch defective.
Replace all latch/door switches.
Adjust door and latch switches.
Microwave oven is programmable, 1. Secondary interlock open or loose
but timer does not work.
wiring.
2. Primary interlock switch misadjusted. Adjust door and latch switches.
3. Secondary interlock switch defective. Replace all latch/door switches.
1. Decrease in power source voltage.
Home voltage fluctuations.
Microwave oven output is low;
2. High voltage circuit loose connection Check/replace magnetron.
microwave oven takes a long time
(magnetron filament circuit).
to cook food.
3. Magnetron aging.
Check/replace magnetron.
10
16027303
© 2006 Maytag Services
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to microwave oven and discharge the
high-voltage capacitor before servicing, unless testing requires power.
Symptom
Microwave oven fan motor
engages when power cord is
plugged in.
Microwave oven does not operate,
oven not in standby mode when
power cord is plugged in.
Microwave oven emitting a loud,
buzzing noise.
Microwave oven turntable motor
does not rotate.
Microwave oven stops during
cooking operation.
Microwave oven emits sparks
when cooking.
Microwave oven cooks unevenly.
Microwave oven turntable emits
noise when operating.
Cause
1. Door sensing switch loose connector.
2. Door sensing switch loose wires.
Correction
Check connector and wiring of
door sensing switch.
1. Check input voltage.
2. Defective PCB assembly.
Make sure house outlet works.
Replace PCB assembly.
1.
2.
3.
1.
2.
1.
Check fan and/or fan motor.
Check high voltage transformer.
Replace high voltage diode.
Check wiring of turntable motor.
Replace turntable motor.
Adjust door and latch switches.
Allow microwave oven to cool to
determine if magnetron TCO is
defective. Replace if necessary.
Do not use cookware with
metallic trimming or gold/silver
powder.
Fan and/or fan motor loose.
High voltage transformer loose.
High voltage diode shorted.
Turntable motor wiring loose/open.
Defective turntable motor.
Open or loose wiring of primary
interlock switch.
2. Open thermal (magnetron) cutout.
1. Metallic ware or cooking dishes
touching on the oven wall.
2. Ceramic ware trimmed with gold or
silver powder.
1. Uneven intensity of microwave due
to microwave characteristics.
2. Microwave cavity dirty.
1. Turntable motor loose.
2. Turntable motor defective.
Cover food with plastic wrap or
cover food with a lid.
Clean microwave cavity.
Tighten screws securing motor.
Replace turntable motor.
Checkout Procedure: Fuse
PROBLEM
Fuse blows immediately after door is closed.
Fuse blows immediately after door is opened.
Fuse blows when door is closed and START
key is touched.
CAUSE
Improper operation of the primary interlock and secondary
interlock switches and/or interlock monitor switch.
Malfunction of high voltage transformer; high voltage capacitor
including diode, magnetron, blower motor or circuit board.
NOTES: Replace blown fuse with 20 Amp fuse.
If the fuse is blown due to an improper switch operation, replace all interlock switches, PCB Ass’y and the
fuse simultaneously, and ensure they are connected properly.
Check for microwave energy leakage after replacing interlock and monitor switches.
© 2006 Maytag Services
16027303
11
Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to microwave oven and discharge the
high-voltage capacitor before servicing, unless testing requires power.
Error Code Table
Error Code
Possible Cause
Keypad shorted 10 seconds or longer.
Sticky keypad(s).
E03
Convection motor or convection heater open.
Motor and/or heater unplugged, wiring or PCB
assembly.
E11
Gas sensor open error.
Sensor unplugged, wiring or PCB assembly.
E12
Gas sensor short error.
Sensor unplugged, wiring or PCB assembly.
E13
T1 Max time error (oven did not preheat properly).
PCB assembly.
E21
Thermal sensor open error.
Sensor unplugged, wiring or PCB assembly.
E22
Thermal sensor short error.
Sensor unplugged, wiring or PCB assembly.
E23
PREHEAT did not reach preset temperature within 30
minutes. Preheat cycle canceled.
Convection heater or grill heater unplugged, wiring
or PCB assembly.
Microwave temperature reaches 500° F (260° C) in
overheat condition. Microwave cancels all functions.
Thermal or gas sensor, wiring or PCB assembly.
E61
Sensor open error.
Sensor unplugged, wiring or PCB assembly.
E62
Sensor shorted error.
Sensor shorted or PCB assembly.
E63
T1 Max Time error.
PCB assembly.
E24
12
Explanation
SE
16027303
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component Testing Procedures
Illustration
Component
High voltage
transformer
120 V
Secondary
Primary
JMV9169BA*,
JMV8166BA*
0V
Filament
High voltage
transformer
120 V
Secondary
Primary
AMV6167BD*
0V
Filament
High voltage
transformer
120 V
Secondary
Primary
MMV5207B**,
JMV8208B**,
MMV4205BA*
0V
Filament
High voltage
transformer
120 V
Secondary
Primary
AMV5164BC*
0V
Filament
High voltage
transformer
120 V
Secondary
Primary
AMV5164BA*,
MMV5165BA*,
AMV1154BA*,
MMV1153BA*,
UMV1152CA*
0V
Filament
Lamp receptacle
© 2006 Maytag Services
Test Procedure
Discharge Capacitor
Disconnect connector and measure
continuity with meter on R x 1 scale:
Secondary .........................................
Filament ............................................
Primary (High & Low) ........................
(Measure at room temp., or 70° F/ 22° C.)
Measure continuity with meter on "High"
scale: Primary winding to ground.................
Filament winding to ground ...............
Discharge Capacitor
Disconnect connector and measure
continuity with meter on R x 1 scale:
Secondary .........................................
Filament ............................................
Primary (High & Low) ........................
(Measure at room temp., or 70° F/ 22° C.)
Measure continuity with meter on "High"
scale: Primary winding to ground.................
Filament winding to ground ...............
Discharge Capacitor
Disconnect connector and measure
continuity with meter on R x 1 scale:
Secondary .........................................
Filament ............................................
Primary (High & Low) ........................
(Measure at room temp., or 70° F/ 22° C.)
Measure continuity with meter on "High"
scale: Primary winding to ground.................
Filament winding to ground ...............
Discharge Capacitor
Disconnect connector and measure
continuity with meter on R x 1 scale:
Secondary .........................................
Filament ............................................
Primary (High & Low) ........................
(Measure at room temp., or 70° F/ 22° C.)
Measure continuity with meter on "High"
scale: Primary winding to ground.................
Filament winding to ground ...............
Discharge Capacitor
Disconnect connector and measure
continuity with meter on R x 1 scale:
Secondary .........................................
Filament ............................................
Primary..............................................
(Measure at room temp, or 70° F/ 22° C.)
Measure continuity with meter on "High"
scale: Primary winding to ground.................
Filament winding to ground ...............
Results
Approx. 118-123 Ω.
Continuity.
Less than 1 Ω.
Infinite Ω.
Infinite Ω.
Approx. 65-69 Ω.
Continuity.
Less than 1 Ω.
Infinite Ω.
Infinite Ω.
Approx. 88-92 Ω.
Continuity.
Less than 1 Ω.
Infinite Ω.
Infinite Ω.
Approx. 67-72 Ω.
Continuity.
Less than 1 Ω.
Infinite Ω.
Infinite Ω.
Approx. 100-104 Ω.
Continuity.
Less than 1 Ω.
Infinite Ω.
Infinite Ω.
Test continuity of receptacle terminals ........... Continuity when known good bulb is
inserted.
16027303
13
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Illustration
Component
Low voltage
transformer
Low voltage
transformer
AMV5164BC*,
MMV5165BA*
Test Procedure
Remove low voltage transformer from control
circuit board and check:
(Measure at room temp., or 68° F/20° C.)
Between pins 1 and 2 (Input)....................
Between pins 4 and 5 (19v output) ...........
Between pins 6 and 7 (7.0v output) ..........
Between pins 7 and 8 (2.7v output) ..........
Remove low voltage transformer from control
circuit board and check:
(Measure at room temp., or 68° F/20° C.)
Between pins 1 and 2 (Input)....................
Between pins 4 and 5 (19v output) ...........
Between pins 7 and 8 (2.7v output) ..........
Approx. 128 Ω..
Approx. 2 Ω..
Approx. 2 Ω..
Approx. 5 Ω..
Approx. 243 Ω..
Approx. 11 Ω..
Approx. 2 Ω..
Low voltage
transformer
AMV5164BA*,
AMV1154BA*,
MMV1153BA*,
UMV1152CA*
Remove low voltage transformer from control
circuit board and check:
(Measure at room temp., or 68° F/20° C.)
Between pins 1 and 2 (Input).................... Approx. 379 Ω..
Between pins 4 and 5 (19v output) ........... Approx. 11 Ω..
Between pins 7 and 8 (2.7v output) .......... Approx. 2 Ω..
Magnetron
Discharge Capacitor
Remove wires from magnetron and connect
ohmmeter to terminals. Also check between
each terminal and ground.
High Voltage
Capacitor
High Voltage Diode
Power Control Relay
Grill heater element
JMV9169BA*,
JMV8166BA*,
AMV6167BD*
14
Results
Between Terminals: Less than 1 Ω.
Each Terminal to Ground: Infinite Ω..
NOTE: This test is not conclusive. If
microwave oven does not heat and all
other components test good, replace the
magnetron and retest.
Between Terminals: Meter should
momentarily indicate continuity, then 9
MΩ (deflection). A steady 9 MΩ indicates
an open capacitor. Steady continuity
indicates a shorted capacitor. In either
case, replace capacitor.
Check resistance between each terminal and
capacitor case. .................................................. Infinite Ω.
Discharge Capacitor
Infinite resistance should be measured in
one direction and several hundred KΩ in
Remove diode lead from capacitor and
the opposite direction.
connect ohmmeter.
NOTE: Ohmmeter must contain a battery
of 6 volts minimum.
Reverse leads for second test.
Disconnect the leads. Place water in the
Cycle On Cycle Off
Power Level
microwave oven and select power levels 1
(Continuity)
(Open)
through 10. Press the START pad. Check
1
4 sec
26 sec
continuity between the terminals of the relays ...
2
7 sec
23 sec
3
10 sec
20 sec
4
13 sec
17 sec
5
16 sec
14 sec
6
19 sec
11 sec
7
22 sec
8 sec
8
25 sec
5 sec
9
28 sec
2 sec
10
30 sec
0 sec
Discharge Capacitor
Remove wires from capacitor terminals and
connect ohmmeter, set on highest resistance
scale to terminals.
Remove all wires from heater.
Measure resistance across terminals ................ Approx. 15-25 Ω (70° F, 20° C).
16027303
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Illustration
Component
Convection heater element
JMV9169BA*,
JMV8166BA*,
AMV6167BD*
Convection motor
JMV9169BA*,
JMV8166BA*,
AMV6167BD*
Primary interlock switch test
(Bottom switch)
1
Test Procedure
Results
Remove all wires from heater.
Measure resistance across terminals .......... Approx. 15-25 Ω (70° F, 20° C).
Remove all wires from motor.
Measure resistance across coil.................... Approx. 14.5 - 17 Ω.
Measure resistance between
terminals 1 and 2:
Door Open................................................... Open (Infinite).
Door Closed ................................................ Continuity.
2
Secondary interlock switch
test
(Top switch)
Measure resistance between
terminals 1 and 2:
Door Open................................................... Open (Infinite).
Door Closed ................................................ Continuity.
Interlock monitor switch test
(Middle switch)
Measure resistance between
terminals 1 and 2:
Door Open................................................... Continuity.
Door Closed ................................................ Open (Infinite).
1
2
C
B A
Fan motor
MMV4205BA*, AMV5206BA*,
MMV5207BA, JMV8208B**,
JMV9169BA*, JMV8166BA*,
AMV6167BD*
Remove all wires from motor.
Stirrer Motor
UMV1152CA*, AMV1154BA*,
AMV5164BA*, MMV1153BA*,
MMV5165BA*
Stirrer Motor
Measure voltage across terminals ............... Approx. 120 VAC.
Measure resistance across terminals .......... Approx. 3 to 4 Ω.
Turntable Motor
UMV1152CA*, AMV1154BA*,
AMV5164BA*, MMV1153BA*,
MMV5165BA*
Turntable Motor
Measure resistance ..................................... Approx. 28 - 35 Ω.
Infinite or several, motor is defective.
Measure voltage across terminals ............... Approx. 120 VAC.
Measure resistance across terminals .......... Approx. 108 to 132 kΩ.
Measure voltage across terminals ............... Approx. 120 VAC.
Measure resistance across terminals .......... Approx. 3 to 4 Ω.
Measure voltage across terminals ............... Approx. 120 VAC.
Measure resistance across terminals .......... Approx. 108 to 132 kΩ.
Damper Motor
JMV9169BA*, JMV8166BA*,
AMV6167BD*
Measure voltage across terminals ............... Approx. 120 VAC.
Measure resistance across terminals .......... Approx. 3 to 4 kΩ.
Louvre Motor
JMV8208B**, JMV9169BA*,
JMV8166BA*, AMV6167BD*
Measure voltage across terminals ............... Approx. 120 VAC.
Measure resistance across terminals .......... Approx. 3100 to 3900 kΩ.
© 2006 Maytag Services
16027303
15
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Illustration
Component
Ventilation Motor
JMV8166BA*, AMV6167BD*
Test Procedure
Results
Discharge Capacitor
Remove two wires to run capacitor and
measure resistance across the wires ........... Approx. 75 Ω. (Tests all 3 windings.)
Ventilation Motor
JMV9169BA*
Discharge Capacitor
Remove two wires to run capacitor and
measure resistance across the wires ........... Approx. 25 Ω. (Tests all 3 windings.)
Vent Blower Motor (run)
Capacitor
Between Terminals: Meter should
momentarily indicate several ohms,
Remove one wire from capacitor terminals then return to infinity (deflection). If
no deflection occurs, or if continuous
and connect ohmmeter. Set on highest
deflection occurs, replace capacitor.
resistance scale.
Terminal to Case: Infinite resistance.
Disconnect all wires from TCO.
Non–resetable.
Measure resistance across terminals .......... Open: ..... 212° F (100° C).
Cavity (Flame Sensor)
Thermal Cut-Out
(Thermostat)
Discharge Capacitor
Cavity (Flame Sensor)
Thermal Cut-Out
(Thermostat)
Disconnect all wires from TCO.
Resetable.
Measure resistance across terminals ........... Open: ..... 302° F (150° C).
Closed: .. 140° F (60° C).
Cavity (Flame Sensor)
Thermal Cut-Out
(Thermostat)
Disconnect all wires from TCO.
Non–resetable.
Measure resistance across terminals .......... Open: ..... 248° F (120° C).
Magnetron Thermal Cut-Out
(Thermostat)
Disconnect all wires from TCO.
Resetable.
Measure resistance across terminals. .......... Open: ..... 302° F (150° C).
Closed: .. 140° F (60° C).
Hood Thermal Cut-Out
(Thermostat)
Disconnect all wires from TCO.
Measure resistance across terminals ...........
NOTE: This TCO only works in an
overheat condition. Otherwise, it will
measure "open" when testing.
Disconnect all wires from TCO.
Measure resistance across terminals. ..........
Bottom Thermal Cut-Out
(Thermostat)
Sensor
Resetable.
Open: ..... 158° F (70° C). Vent fan
engaged.
Closed: .. 104° F (40° C). Vent fan
disengaged.
Non–resetable.
Open: ..... 248° F (120° C).
Remove the red and black wires, connect
meter to red and black wires and measure
continuity...................................................... 30 Ω.
NOTE: Do not connect the meter to the
white and orange wires, as this may
damage the sensor.
Control Panel Sensor Test
Illustration
Component
Sensor Test
1
2
3
16
Sensor Test
AMV5164B**,
MMV5165BA*
Test Procedure
Apply power to microwave for 5 minutes.
Press AUTO DEFROST and REHEAT
pads simultaneously and monitor display
for V-Out value .............................................
NOTE: Press AUTO DEFROST and
POPCORN pads for model AMV6167BD*.
Apply power to microwave for 5 minutes.
Press AUTO DEFROST and REHEAT
pads simultaneously and monitor display
for V-Out value .............................................
16027303
Results
Less than 6 .......... Sensor failure.
15 to 185.............. Normal.
More than 213...... Sensor failure.
Less than 10 .......... Sensor failure.
10 to 150................ Normal.
More than 150........ Sensor failure.
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Power Test (Traditional Test Method)
Test equipment required is Amana power test kit R0157397 (Fahrenheit), or
Menumaster power test kit M95D5 (Celsius).
1. Fill the plastic container to the 1000 ml. line with cool tap water.
2. Using the thermometer; stir the water, measure, and record the water temperature.
Initial water temperature should be approximately 60° F (16° C).
3. Place container on the center of the oven shelf and heat the water for
33 seconds for ovens with more than 1550 watts or 63 seconds for ovens with less than 1550 watts.
NOTE: Use a watch second hand, not the oven timer.
4. Stir the water, measure and record the temperature of the water after heating time is complete.
5. Subtract the starting water temperature (Step 2), from the ending water temperature (Step 4) to obtain the
temperature rise (∆T).
6. See the Traditional Power Test Temperature Chart below.
NOTES: • The IEC-705 test method requires precision measurements and equipment. It is not practical to
perform the IEC test in the field. To convert the traditional power test results to the approximate IEC705 rating, take the traditional power test results and add 100 watts per magnetron for the unit being
tested.
Example:
850
watts output using the traditional power test
+ 100
950
watts (1 magnetron X 100 watts)
Approximate IEC-705 results
• Always perform power test three times for accuracy, changing the water after each test is performed.
• Variation or errors in the test procedure will cause a variance in the temperature rise. Additional power
tests should be made if temperature rise appears marginal.
• Low line voltage will cause lower temperature rise.
Traditional Power Test Temperature Chart
SIXTY-THREE (63) SECONDS run time chart for units less than 1550 watts cooking power
Fahrenheit
∆T
(° F)
16
17
18
19
20
21
22
Cooking
Power Output
620
659
697
736
775
814
852
© 2006 Maytag Services
Celsius
∆T
Cooking
(° F) Power Output
23
891
24
930
25
969
26
1007
27
1046
28
1085
29
1124
∆T
(° C)
7
8
9
10
11
12
13
14
16027303
Cooking
Power Output
490
560
630
700
770
840
910
980
∆T
(° C)
15
16
17
18
19
20
21
22
Cooking
Power Output
1050
1120
1190
1260
1330
1400
1470
1540
17
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
UMV1152CA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
Touch Pad/Control
Panel
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
MMV1153BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
18
Pad
1
2
3
4
5
6
7
8
9
0
Enter/Start
Add 30 Seconds
Popcorn
Baked Potato
Vent Hi/Lo/Off
Reheat
Auto Defrost
Power Level
Light Hi/Lo/Off
Stop Clear
Clock
Kitchen Timer
Sound On/Off
Vegetables
Cook
Pizza Slice
Pad
1
2
3
4
5
6
7
8
9
0
Enter/Start
Add 30 Seconds
Popcorn
Baked Potato
Vent Hi/Lo/Off
Reheat
Auto Defrost
Power Level
Light Hi/Lo/Off
Stop Clear
Clock
Kitchen Timer
Sound On/Off
Vegetables
Cook
Pizza Slice
16027303
Results
Trace
2 & 12
3 & 12
4 & 12
5 & 12
6 & 12
1 & 13
2 & 13
3 & 13
4 & 13
1 & 12
1&9
2&9
3&9
4&9
6&9
2 & 10
3 & 10
4 & 10
6 & 10
1 & 11
2 & 11
3 & 11
4 & 11
6 & 11
5 & 13
6 & 13
Trace
2 & 12
3 & 12
4 & 12
5 & 12
6 & 12
1 & 13
2 & 13
3 & 13
4 & 13
1 & 12
1&9
2&9
3&9
4&9
6&9
2 & 10
3 & 10
4 & 10
6 & 10
1 & 11
2 & 11
3 & 11
4 & 11
6 & 11
5 & 13
6 & 13
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
AMV1154BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
Touch Pad/Control
Panel
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
AMV5164BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
© 2006 Maytag Services
Pad
1
2
3
4
5
6
7
8
9
0
Enter/Start
Add 30 Seconds
Popcorn
Baked Potato
Vent Hi/Lo/Off
Reheat
Auto Defrost
Power Level
Light Hi/Lo/Off
Stop Clear
Clock
Kitchen Timer
Sound On/Off
Vegetables
Cook
Pizza Slice
Pad
1
2
3
4
5
6
7
8
9
0
Vegetables
Cook
Pizza Slice
Option
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Add 30 Seconds
Reheat
Light Timer
Control Setup
Turntable On/Off
Kitchen Timer
Custom Program
Auto Defrost
Enter/Start
Clock
Power Level
Stop/Clear
Vent Hi/Lo/Off
16027303
Results
Trace
2 & 12
3 & 12
4 & 12
5 & 12
6 & 12
1 & 13
2 & 13
3 & 13
4 & 13
1 & 12
1&9
2&9
3&9
4&9
6&9
2 & 10
3 & 10
4 & 10
6 & 10
1 & 11
2 & 11
3 & 11
4 & 11
6 & 11
5 & 13
6 & 13
Trace
8 & 16
7 & 16
6 & 16
5 & 16
4 & 16
3 & 16
9 & 15
8 & 15
7 & 15
9 & 16
8 & 10
9 & 10
3 & 11
2 & 10
6 & 12
7 & 12
8 & 12
9 & 12
4 & 13
5 & 13
6 & 13
7 & 13
8 & 13
9 & 13
3 & 14
4 & 14
5 & 14
9 & 14
3 & 15
4 & 15
6 & 15
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
19
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
MMV5165BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
20
Pad
1
2
3
4
5
6
7
8
9
0
5 Speed
On/Off
Vegetables
Cook
Option
Pizza Slice
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Delay Off
Add 30 Seconds
Reheat
Light Timer
Control Setup
Kitchen Timer
Custom Program
Auto Defrost
Enter/Start
Clock
Power Level
Stop Clear
16027303
Results
Trace
8 & 16
7 & 16
6 & 16
5 & 16
4 & 16
3 & 16
9 & 15
8 & 15
7 & 15
9 & 16
3 & 10
4 & 10
8 & 10
9 & 10
2 & 11
3 & 11
6 & 12
7 & 12
8 & 12
9 & 12
3 & 13
4 & 13
5 & 13
6 & 13
7 & 13
9 & 13
3 & 14
4 & 14
5 & 14
9 & 14
3 & 15
4 & 15
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
MMV4205BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
© 2006 Maytag Services
Pad
1
2
3
4
5
6
7
8
9
0
Pizza Slice
Vegetables
Cook
Beverage
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Add 30 Seconds
Reheat
Light Timer
Control Setup
Turntable On/Off
Kitchen Timer
Custom Program
Auto Defrost
Enter Start
Snacks
Kids Meals
Soften/Melt
Clock
Power Level
Stop/Clear
Vent Hi/Lo/Off
Option
16027303
Results
Trace
6 & 15
5 & 15
4 & 15
3 & 15
2 & 15
1 & 15
7 & 14
6 & 14
5 & 14
7 & 15
1 & 10
2 & 10
3 & 10
3 & 11
4 & 11
5 & 11
6 & 11
7 & 11
2 & 12
3 & 12
4 & 12
5 & 12
6 & 12
7 & 12
1 & 13
2 & 13
3 & 13
4 & 13
5 & 13
6 & 13
7 & 13
1 & 14
2 & 14
4 & 14
9 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
21
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
AMV5206BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
22
Results
Pad
1
2
3
4
5
6
7
8
9
0
Pizza Slice
Vegetables
Cook
5 Speed
On/Off
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Option
Delay Off
Add 30 Seconds
Reheat
Light Timer
Control Setup
Turntable On/Off
Kitchen Timer
Custom Program
Auto Defrost
Enter Start
Snacks
Kids Meals
Soften/Melt
Clock
Power Level
Stop/Clear
16027303
Trace
6 & 15
5 & 15
4 & 15
3 & 15
2 & 15
1 & 15
7 & 14
6 & 14
5 & 14
7 & 15
1 & 10
2 & 10
3 & 10
6 & 10
7 & 10
4 & 11
5 & 11
6 & 11
7 & 11
9 & 11
1 & 12
2 & 12
3 & 12
4 & 12
5 & 12
6 & 12
7 & 12
1 & 13
2 & 13
3 & 13
4 & 13
5 & 13
6 & 13
7 & 13
1 & 14
2 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
MMV5207BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
© 2006 Maytag Services
Results
Pad
1
2
3
4
5
6
7
8
9
0
Pizza Slice
Vegetables
Cook
5 Speed
On/Off
Option
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Delay Off
Add 30 Seconds
Reheat
Light Timer
Control Setup
Kitchen Timer
Custom Program
Auto Defrost
Enter Start
Snacks
Kids Meals
Soften/Melt
Clock
Power Level
Stop/Clear
16027303
Trace
6 & 15
5 & 15
4 & 15
3 & 15
2 & 15
1 & 15
7 & 14
6 & 14
5 & 14
7 & 15
1 & 10
2 & 10
3 & 10
6 & 10
7 & 10
9 & 10
4 & 11
5 & 11
6 & 11
7 & 11
1 & 12
2 & 12
3 & 12
4 & 12
5 & 12
7 & 12
1 & 13
2 & 13
3 & 13
4 & 13
5 & 13
6 & 13
7 & 13
1 & 14
2 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
23
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
JMV8208BA*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
24
Pad
1
2
3
4
5
6
7
8
9
0
Pizza Slice
Vegetables
Cook
5 Speed
On/Off
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Delay Off
Add 30 Seconds
Reheat
Light Timer
Control Setup
Kitchen Timer
Option
Custom Program
Auto Defrost
Enter Start
Snacks
Kids Meals
Soften/Melt
Clock
Power Level
Stop/Clear
16027303
Results
Trace
6 & 15
5 & 15
4 & 15
3 & 15
2 & 15
1 & 15
7 & 14
6 & 14
5 & 14
7 & 15
1 & 10
2 & 10
3 & 10
6 & 10
7 & 10
4 & 11
5 & 11
6 & 11
7 & 11
1 & 12
2 & 12
3 & 12
4 & 12
5 & 12
7 & 12
9 & 12
1 & 13
2 & 13
3 & 13
4 & 13
5& 13
6 & 13
7 & 13
1 & 14
2 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Panel/Control Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform
test.
AMV6167BD*
Check for continuity.
When touched:
Less than 400 Ω.
When not touched:
More than 1 mega Ω.
© 2006 Maytag Services
Pad
0
1
2
3
4
5
6
7
8
9
Control Setup
Pizza Slice
Baked Potato
Popcorn
Combination Cooking
Convection
Clock
Micro. Convection
Auto Cook
Auto Defrost
Reheat
Sensor Cook
Option
Snacks
Soften/Melt
Stop/Clear
Enter/Start
Power Level
Kitchen Timer
Delay Off
5 Speed
On/Off
Light Timer
Light Hi/Lo/Off
Turntable On/Off
Add 30 Seconds
16027303
Results
Trace
5 & 13
6 & 12
5 & 12
4 & 12
3 & 12
2 & 12
9 & 13
8 & 13
7 & 13
6 & 13
2 & 10
3 & 10
4 & 10
5 & 10
6 & 10
8 & 10
2 & 11
4 & 11
6 & 11
7 & 11
8 & 11
9 & 11
1 & 12
8 & 12
9 & 12
2 & 13
3 & 13
4 & 13
2 & 14
3 & 14
4 & 14
5 & 14
6 & 14
7 & 14
8 & 14
9 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
25
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Panel/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform
test.
JMV8166BA*
Check for continuity.
When touched:
Less than 400 Ω.
When not touched:
More than 1 mega Ω.
26
Pad
0
1
2
3
4
5
6
7
8
9
Control Setup
Pizza Slice
Baked Potato
Popcorn
Combination Cooking
Convection
Clock
Micro. Convection
Auto Cook
Auto Defrost
Reheat
Sensor Cook
Option
Snacks
Soften/Melt
Stop/Clear
Enter/Start
Power Level
Kitchen Timer
Delay Off
5 Speed
On/Off
Light Timer
Light Hi/Lo/Off
Turntable On/Off
Add 30 Seconds
16027303
Results
Trace
5 & 13
6 & 12
5 & 12
4 & 12
3 & 12
2 & 12
9 & 13
8 & 13
7 & 13
6 & 13
2 & 10
3 & 10
4 & 10
5 & 10
6 & 10
8 & 10
2 & 11
4 & 11
6 & 11
7 & 11
8 & 11
9 & 11
1 & 11
8 & 12
9 & 12
2 & 13
3 & 13
4 & 13
2 & 14
3 & 14
4 & 14
5 & 14
6 & 14
7 & 14
8 & 14
9 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Panel/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
JMV9169BA*
When touched:
Less than 400 Ω.
When not touched:
More than 1 mega Ω.
© 2006 Maytag Services
Pad
0
1
2
3
4
5
6
7
8
9
Control Setup
Pizza Slice
Baked Potato
Popcorn
Combination Cooking
Broil
Convection
Clock
Auto Broil
Micro. Convection
Auto Cook
Auto Defrost
Reheat
Sensor Cook
Snacks
Soften/Melt
Stop/Clear
Enter/Start
Power Level
Kitchen Timer
Delay Off
5 Speed
On/Off
Light Timer
Light Hi/Lo/Off
Turntable On/Off
Add 30 Seconds
16027303
Results
Trace
5 & 13
6 & 12
5 & 12
4 & 12
3 & 12
2 & 12
9 & 13
8 & 13
7 & 13
6 & 13
2 & 10
3 & 10
4 & 10
5 & 10
6 & 10
7 & 10
8 & 10
2 & 11
3 & 11
4 & 11
6 & 11
7 & 11
8 & 11
9 & 11
8 & 12
9 & 12
2 & 13
3 & 13
4 & 13
2 & 14
3 & 14
4 & 14
5 & 14
6 & 14
7 & 14
8 & 14
9 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
27
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
AMV5164BC*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
28
Pad
1
2
3
4
5
6
7
8
9
0
Vegetables
Cook
Pizza Slice
Option
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Add 30 Seconds
Reheat
Light Timer
Control Setup
Turntable On/Off
Kitchen Timer
Custom Program
Auto Defrost
Enter/Start
Clock
Power Level
Stop/Clear
Vent Hi/Lo/Off
16027303
Results
Trace
8 & 16
7 & 16
6 & 16
5 & 16
4 & 16
3 & 16
9 & 15
8 & 15
7 & 15
9 & 16
8 & 10
9 & 10
3 & 11
2 & 12
6 & 12
7 & 12
8 & 12
9 & 12
4 & 13
5 & 13
6 & 13
7 & 13
8 & 13
9 & 13
3 & 14
4 & 14
5 & 14
9 & 14
3 & 15
4 & 15
6 & 15
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
MMV5207BC*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
© 2006 Maytag Services
Pad
1
2
3
4
5
6
7
8
9
0
Pizza Slice
Vegetables
Cook
5 Speed
On/Off
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Delay Off
Add 30 Seconds
Reheat
Light Timer
Control Setup
Kitchen Timer
Custom Program
Auto Defrost
Enter Start
Snacks
Kids Meals
Soften/Melt
Clock
Option
Power Level
Stop/Clear
16027303
Results
Trace
6 & 15
5 & 15
4 & 15
3 & 15
2 & 15
1 & 15
7 & 14
6 & 14
5 & 14
7 & 15
1 & 10
2 & 10
3 & 10
6 & 10
7 & 10
4 & 11
5 & 11
6 & 11
7 & 11
1 & 12
2 & 12
3 & 12
4 & 12
5 & 12
7 & 12
1 & 13
2 & 13
3 & 13
4 & 13
5& 13
6 & 13
7 & 13
9 & 13
1 & 14
2 & 14
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
29
Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to microwave oven and discharge the
high voltage capacitor before servicing, unless testing requires power.
Component
Touch Pad/Control
Panel
Test Procedure
Removal of Touch
Pad/Control Panel is
required to perform test.
Check for continuity.
JMV8208BC*
When touched: Less than
400 Ω.
When not touched: More
than 1 mega Ω.
30
Pad
1
2
3
4
5
6
7
8
9
0
Pizza Slice
Vegetables
Cook
5 Speed
On/Off
Baked Potato
Popcorn
Light Hi/Lo/Off
1 Pound Defrost
Delay Off
Add 30 Seconds
Reheat
Light Timer
Control Setup
Kitchen Timer
Custom Program
Auto Defrost
Enter Start
Snacks
Kids Meals
Soften/Melt
Clock
Power Level
Stop/Clear
Option
16027303
Results
Trace
6 & 15
5 & 15
4 & 15
3 & 15
2 & 15
1 & 15
7 & 14
6 & 14
5 & 14
7 & 15
1 & 10
2 & 10
3 & 10
6 & 10
7 & 10
4 & 11
5 & 11
6 & 11
7 & 11
1 & 12
2 & 12
3 & 12
4 & 12
5 & 12
7 & 12
1 & 13
2 & 13
3 & 13
4 & 13
5& 13
6 & 13
7 & 13
1 & 14
2 & 14
9 & 15
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
© 2006 Maytag Services
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W ARNING
High voltage is present at the high voltage terminal of the
high voltage transformer during any cooking cycle.
It is neither necessary or advisable to attempt
measurement of the high voltage.
3. To place door back on unit, place bottom pin into hole
first and then align the top pin. Once pins are aligned
push door downward to lock into place.
4. Replace front grille to complete assembly.
Before touching any oven components or wiring, always
unplug the oven from its power source and discharge
capacitor.
Grille Removal
The top full-width grille is removable for service to some
components, such as: humidity sensor, oven light, door
removal, flame sensor, vent motor capacitor, fuse,
control panel, and stirrer motor (some models).
Grille Removal
1. Disconnect power to oven.
2. Remove screws located in front on top of microwave
securing grille.
Door Disassembly
1. Disconnect power to oven and remove oven door, see
"Door Removal" procedure.
2. Pry away choke cover, by placing a tool in the upper
right corner of the door and gently prying outward on
the choke cover. Continue to work around the door
casing until choke cover is completely loose.
!
CAUTION
To avoid property damage, care must be taken when
prying choke cover from oven door.
3. Pull outward on the top portion of the grille releasing
the tabs.
4. Reassemble in reverse order.
Door Assembly Removal
!
CAUTION
A microwave leakage test must be performed anytime
a door assembly is removed, replaced, disassembled
or adjusted for any reason.
NOTE: The door handle can only be reinstalled by
guiding the top and bottom insertion points into
the correct receiving slots. It is impossible to
reinstall the door handle "upside-down."
Door Removal
1. Disconnect power to oven and remove grille, see
"Grille Removal" procedure.
2. Open the oven door, slowly raise the door evenly,
disengaging the pins at the top and bottom.
NOTE: When aligning the door for assembly, the door
must be opened as much as possible.
© 2006 Maytag Services
3. Slide latch assembly upward and to the left to release
plastic tabs from door frame. Once latch assembly is
loose the spring may be disconnected from the door
frame.
4. Remove screws securing door frame assembly to
door panel.
5. Remove door frame assembly by releasing tabs
around entire door panel.
6. Remove door handle by removing screws securing
handle to door panel.
7. Remove door glass by releasing tab securing door
glass baffle. Remove baffle, then slide door glass to
the right slightly, then push the door glass upward to
release the glass from the track.
8. Reassemble in reverse order.
16027303
31
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W A RN ING
Printed Circuit Board Removal
The circuit board is located at the top on back of the
control panel.
!
CAUTION
A microwave leakage test must be performed anytime
a door assembly is removed, replaced, disassembled,
or adjusted for any reason.
Control Panel Removal
The control panel is made up of several components,
such as a printed circuit board and touch panel.
1. Disconnect oven power and remove grille, see "Grille
Removal" procedure.
2. Remove screw located at the top of touch panel. Lift
control panel up and out to release bottom tab
connections.
3. Place control panel on a flat surface.
4. Reassemble in reverse order.
Control Panel/Switch Membrane Disassembly
P.C. Board Removal
1. Disconnect oven power and remove grille, see "Grille
Removal" procedure.
2. Remove control panel, see "Control Panel Removal"
procedure.
3. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
4. Disconnect ribbon connector by sliding top part of
connector upward. Once in released position remove
ribbon from connector by siding ribbon side-to-side.
NOTE: Caution should be used when removing cable
from connector. Ribbon cable has two holes
which connector locks ribbon in place.
5. Disconnect and mark the wire connectors from
circuit board.
6. Remove screws securing circuit board to control
panel assembly.
7. Reassemble in reverse order.
NOTE: Do not flex circuit board.
32
16027303
© 2006 Maytag Services
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W ARNING
Control Key Panel Removal
The key panel has one ribbon connection on the circuit
board.
Vent plate
The key panel pads can be checked through a continuity
test. Operations of key pad can be checked by
measuring connections at end of ribbon, using high
ohms scale.
Power cord cover
Door
Plastic fastener
Hook
Mounting
plate
Outter case
Holes
Vent grille
Controller
F.P.C.
Stirrer Assembly Removal
connector
Motor driven antenna assembly is located at the top of
the cavity, using a top feed wave guide.
Terminal
socket
Control Key Panel Removal
1. Disconnect power to microwave oven.
2. Remove control panel, see "Control Panel Removal"
procedure.
3. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
4. Disconnect ribbon connector by sliding top part of
connector upward. Once in released position remove
ribbon from connector by sliding ribbon side-to-side.
Stirrer Blade Removal
1. Disconnect power to oven and open the oven door.
2. Carefully pry downward on the plastic rivets securing
the stirrer cover.
3. Rotate slightly and pull down on stirrer fan cover .
4. Reassemble in reverse order.
NOTE: Caution should be used when removing cable
from connector. Ribbon cable has two holes
which connector locks ribbon in place.
5. Peel failed key pad off and replace with new key pad.
6. Reassemble in reverse order.
Outer Case Removal
NOTE: This procedure requires removal of unit.
1. Disconnect power to oven and remove grille, see
"Grille Removal" procedure.
2. Remove oven door see "Door Removal" procedure.
3. Remove screws securing air duct to outer case.
4. Remove screws securing outer case to chassis.
5. Remove screws securing vent plate to outer case.
6. Remove screw securing power cord cover to outer
case and remove power cord cover (if equipped).
7. Slide outer case towards the rear of the unit, guide
power cord though outer case power cord hole.
8. Place outer case in a safe location.
9. Reassemble in reverse order.
© 2006 Maytag Services
16027303
33
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W A RN ING
Interlock Door Latch Switches Removal
Primary switch is operated by the top latch pawl.
Interlock Switch Removal
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Test interlock switches before removing, see Testing
Procedures.
4. Disconnect and label wire connections.
5. Remove interlock switch.
Latch Board
Secondary Interlock Switch
Adjusting Interlocks
The interlock monitor and primary switches act as a final
safety switch, protecting the operator from microwave
energy. After adjusting the interlock switches, verify
connections are correctly connected.
For door fit and switch operation, switch housing is
adjustable.
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Loosen switch housing mounting screws on vertical
flange.
4. Close oven door, move latch board upward toward the
top of the oven and/or away from the door latch until
gaps are less than 1/64–inch (0.5 mm).
5. Hold latch board securely for proper switch operation
and door fit, retighten screws.
6. Open the oven door slowly, watching the switches.
Verify switches release in the following order.
• Primary interlock switch
• Secondary interlock switch
• Monitor interlock switch
NOTE: Adjust the latch board until all switches operate
in proper sequence.
Monitor Interlock Switch
7. Close the oven door slowly, watching the switches.
Verify switches active in the following order.
• Monitor interlock switch
• Secondary interlock switch
• Primary interlock switch
8. When proper sequence of switch has been achieved,
tighten the latch board securely.
!
CAUTION
A microwave leakage test must be preformed anytime
a door assembly is removed, replaced, disassembled
or adjustment of latch board is made.
Primary Interlock Switch
!
CAUTION
Before replacing a blown monitor fuse, test the
primary interlock switch, secondary interlock switch,
monitor switch, and power relay contacts for proper
operation. If the monitor fuse is blown by a failed
switch operation, all switches and printed circuit board
must be replaced.
34
16027303
© 2006 Maytag Services
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W ARNING
High Voltage Capacitor Removal
High voltage capacitor should always be discharged by
shorting a terminal to a chassis ground. The capacitor
has a internal "shunt" resistor, but the mechanical
discharge should always be performed to avoid personal
injury.
High Voltage Capacitor Removal
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor by connecting a
jumper wire to the terminal of high voltage capacitor
with the diode connected to it. Connect the other
end of the jumper wire to a well insulated screwdriver
and touch a nearby chassis ground screw.
3. Remove screws that secure capacitor and diode.
4. Slide capacitor mounting bracket out of the slots and
pull outward on capacitor, diode and bracket.
5. Reassemble in reverse order.
Diode Removal
The diode is located next to the high voltage capacitor.
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Disconnect diode wire terminal from high voltage
capacitor and remove screw securing diode to
ground.
4. Reassemble in reverse order.
Fuse Removal
1. Disconnect power and remove grille, see "Grille
Removal" procedure.
2. Remove and replace fuse and reassemble in reverse
order.
!
CAUTION
Before replacing a blown monitor fuse, test the
primary interlock switch, secondary interlock switch,
monitor switch, and power relay contacts for proper
operation. If the monitor fuse is blown by a failed
switch operation, all switches and printed circuit board
must be replaced.
Magnetron Removal
Magnetron is mounted on the side of the cavity to
provide a top feed single waveguide.
1. Disconnect power to oven and remove grille, see
"Grille Removal" procedure.
2. Remove control panel, see "Control Panel Removal"
procedure.
3. Remove outer case, see "Outer Case Removal"
procedure.
4. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
5. Remove screws securing magnetron to wave guide.
6. Carefully remove the magnetron.
7. Reassemble in reverse order.
Transformer Removal
High voltage transformer can be serviced through the
front of the unit.
Transformer Removal
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Disconnect and label wire leads from transformer.
4. Remove screws securing transformer and remove out
through the front.
5. Reassemble in reverse order.
Replacing Fuse
The fuse is located behind the grille in line with the
power cord on the right side of the unit.
NOTE: When replacing the magnetron, make sure the
gasket is in the correct position and in good
condition.
!
CA UTION
During replacement of magnetron, be certain the R.F.
anode gasket is in place around anode stud.
© 2006 Maytag Services
16027303
35
Disassembly Procedures
!
W A RN ING
!
W ARNING
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
A microwave leakage test must be performed anytime
a magnetron assembly is removed, replaced,
disassembled or adjusted for any reason.
Magnetron Fan Assembly Removal
Magnetron fan motor provides cool air circulation from
an external air source, which provides direct cool air
through air vanes surrounding the magnetron. This
assembly is located above the magnetron.
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Remove outer case, see "Outer Case Removal"
procedure.
4. Remove screws securing sensor to air duct.
5. Disconnect wire terminal; replace with new sensor.
6. Reassemble in reverse order.
1. Follow steps 1 through 5 of "Magnetron Removal"
procedure.
2. Remove fan blade from fan motor.
3. Remove screws securing fan motor to air duct.
4. Label and disconnect wires from fan motor and lift
assembly out.
5. Reassemble in reverse order.
Magnetron Thermal Fuse Removal
NOTE: Thermal fuse is not resettable.
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Remove outer case, see "Outer Case Removal"
procedure.
4. Label and disconnect wire terminals.
5. Remove screw securing thermal fuse to cooling fan.
6. Replace and reassemble in reverse order.
Magnetron Thermal Fuse
Fan Motor
Oven Thermostat Removal
The oven thermostat is on the air duct assembly.
The thermostat is a resettable thermostat.
1. Disconnect power to oven and remove control panel,
see "Control Panel Removal" procedure.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Remove outer case, see "Outer Case Removal"
procedure.
4. Disconnect wire terminals from oven thermostat.
NOTE: Lift upward on left rear corner of air duct to
release oven thermostat.
Humidity Sensor Removal (Select Models)
The sensor is a plug-in device located in the air exhaust
duct.
36
16027303
© 2006 Maytag Services
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W ARNING
Turntable Motor Removal
Vent Blower Removal
1. Disconnect power to oven.
2. Remove screws securing bottom plate cover.
Vent blower is a five speed capacitor run blower
assembly located on top of the oven. The blower is
operated by voltage relays located on the circuit board.
Vent Exhaust Blower Removal
1. Disconnect power to unit and remove unit from its
installation.
2. Remove screws securing damper and motor
assembly to top and back of unit.
3. Remove damper.
4. Lift blower assembly out and disconnect wire
connection wire terminal.
5. Reassemble in reverse order.
NOTE: Place blower assembly wires in slotted area to
avoid pinching of wires.
3. Open the oven door, remove turntable, and gently pry
upward on turntable shaft.
4. Disconnect wire leads from turntable motor.
Damper ASM
Blower ASM
5. Remove screws securing turntable to the oven cavity.
6. Replace and reassemble in reverse order.
© 2006 Maytag Services
16027303
37
Disassembly Procedures
!
To avoid risk of electrical shock, personal injury or
death; disconnect power to microwave oven and
discharge the high voltage capacitor before performing
any disassembly procedures.
W A RN ING
Light Socket Removal
Convection Motor and Heater Element
Removal (Select Models)
1. Disconnect power to oven.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Remove outer case, see "Outer Case Removal"
procedure.
4. Remove screws securing back cover and pull the top
of back cover downward, sliding right side metal tab
from oven cavity.
5. Remove screws securing air duct to chassis and
other components.
6. Label and disconnect wire leads from air duct.
7. Remove magnetron see "Magnetron Removal"
procedure.
8. Remove screws securing bottom plate to chassis.
9. Disconnect wire leads from convection chamber.
10.Remove screws securing convection chamber
assembly and lift assembly from oven cavity.
11. Slide inner convection fan blade off convection motor
shaft.
12.Remove nuts securing convection motor to bracket.
13.Replace and reassembly in reverse order.
1.
2.
3.
4.
5.
6.
Disconnect power to oven.
Remove Grille, see "Grille Removal" procedure.
Remove screws securing bulb holder.
Remove light bulb and socket.
Disconnect wire terminal plug.
Replace and reassemble in reverse order.
Grille Heater Element Removal
(Select Models)
1. Disconnect power to oven.
2. Discharge high voltage capacitor, see "High Voltage
Capacitor Removal" procedure.
3. Remove outer case, see "Outer Case Removal"
procedure.
4. Remove screws securing back cover and pull the top
of back cover downward sliding metal tab on right
side from oven cavity.
5. Remove screws securing air duct to chassis and
other components.
6. Disconnect wire leads from air duct.
7. Remove screw securing upper insulator.
8. Remove screws securing the heater terminal and
heater barrier.
9. Remove screws securing the heater holding bracket.
10.Remove grille heater from cavity.
11. Replace and reassembly in reverse order.
Convection Heater Element Removal
(Select Models)
1. See “Convection Motor Removal;" perform steps 1
through 9.
2. Remove screws at and next to terminals securing
wires and element to heater box.
3. Release metal clip securing element to heater box.
4. Remove element from heater box.
5. Replace and reassembly in reverse order.
38
16027303
© 2006 Maytag Services
Appendix A
The Installation information provided in this service manual is representative of a limited
number of models. Reference the customer’s Installation literature included with the product,
order a copy (if needed), or consult the appropriate website for the specific model.
www.maytag.com or www.amana.com or www.jennair.com
© 2006 Maytag Services
16027303
A–1
Installation Instructions
Installation Instructions
Over the Range Microwave Oven
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT – Save these instructions for
local inspector’s use.
IMPORTANT – Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
•
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
A–2
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
CONTENTS
General information
C
Outside Back Exhaust............................. 18–21
Preparing Rear Wall ................................ 18
Important Safety Instructions .....................3
Attach Mounting Plate to Wall ........... 18, 19
Electrical Requirements ..............................3
Preparation of Top Cabinet ..................... 19
Hood Exhaust ...........................................4, 5
Adjust Blower .................................... 19, 20
Damage – Shipment/Installation .................6
Mount the Microwave Oven............... 20, 21
Parts Included...............................................6
Tools You Will Need .....................................7
Mounting Space............................................7
Step-by-step installation guide
Placement of Mounting Plate ................8–10
Removing the Mounting Plate ................... 8
Finding the Wall Studs .............................. 8
Determining Wall Plate Location ............... 9
Aligning the Wall Plate ............................ 10
Installation Types .................................11–21
A
Recirculating ........................................... 12–13
Attach Mounting Plate to Wall ................. 12
Preparation of Top Cabinet ..................... 12
Mount the Microwave Oven..................... 13
B
Outside Top Exhaust .............................. 14–17
Attach Mounting Plate to Wall ................. 14
Preparation of Top Cabinet ..................... 15
Adjust Blower .......................................... 15
Check Damper Operation........................ 16
Mount Microwave Oven........................... 16
Adjust Exhaust Adaptor........................... 17
Connecting Ductwork .............................. 17
2
© 2006 Maytag Services
16027303
A–3
Installation Instructions
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded outlet.
The installer must perform a ground continuity check
on the power outlet box before beginning the
installation to insure that the outlet box is properly
grounded. If not properly grounded, or if the outlet
box does not meet electrical requirements noted
(under ELECTRICAL REQUIREMENTS), a qualified
electrician should be employed to correct any
deficiencies.
You should have the wall receptacle and circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is very important to have it
replaced with a properly grounded three-prong
wall receptacle, installed by a qualified
electrician.
CAUTION: For personal
safety, remove house fuse or
open circuit breaker before
beginning installation to
avoid severe or fatal shock
injury.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz,
-MMV4205, AMV5206, MMV5207, JMV8208 (USA):
14.8 amps and 1.7 kilowatts.
-MMV5207,JMV8208 (CANADA) / AMV6167:
13 amps and 1.5 kilowatts.
-JMV8166/JMV9169:
14.5 amps and 1.6 kilowatts.
This product must be connected to a supply circuit of
the proper voltage and frequency. Wire size must
conform to the requirements of the National Electrical
Code or the prevailing local code for this kilowatt
rating. The power supply cord and plug should be
brought to a separate 20 ampere branch circuit single
grounded outlet. The outlet box should be located in
the cabinet above the microwave oven. The outlet
box and supply circuit should be installed by a
qualified electrician and conform to the National
Electrical Code or the prevailing local code.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight of
this 59 pound product, plus additional oven loads
of up to 50 pounds or a total weight of 109
pounds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements such
as an island or a peninsula. It must be mounted to
BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal
safety, it is recommended that two people install
this product.
IMPORTANT–PLEASE READ CAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK.
Insure
Insure proper
proper
ground
ground exists
exists
before
use
before use
The power cord of this
appliance is equipped
with a three-prong
(grounding) plug which
mates with a standard
three-prong (grounding)
wall receptacle to
minimize the possibility
of electric shock hazard
from this appliance.
3
A–4
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to
recirculate the air back into the room, proceed to page 11.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
EQUIVALENT
LENGTH
24 Ft.
x
(1)
=
24 Ft.
12 Ft. Straight Duct (6" 12 Ft.
Round)
x
(1)
=
12 Ft.
Rectangular-to-Round 5 Ft.
Transition Adaptor*
x
(1)
=
5 Ft.
=
41 Ft.
Roof Cap
Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.
Total Length
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have
to be cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH*
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Roof Cap
40 Ft.
x
(1)
=
40 Ft.
3 Ft. Straight Duct
(3¼" x 10"
Rectangular)
3 Ft.
x
(1)
=
3 Ft.
90° Elbow
10 Ft.
x
(2)
=
20 Ft.
=
63 Ft.
Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.
Total Length
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be
prepared at the time it is constructed by leaving enough space between the wall studs to accommodate
exhaust.
4
© 2006 Maytag Services
16027303
A–5
Installation Instructions
Installation Instructions
Models AMC4080AA*, MMC5080AA*
Maximum duct length:
NOTE: If you need to install ducts, note that the total
duct length of 3¼" x 10" rectangular or 6" diameter
round duct should not exceed 60 equivalent feet.
Outside ventilation requires a HOOD EXHAUST
DUCT. Read the following carefully.
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as
possible. This ensures clear venting of exhaust and
helps prevent blockages. Also, make sure dampers
swing freely and nothing is blocking the ducts.
For satisfactory air movement, the total duct length of
3¼" x 10" rectangular or 6" diameter round duct
should not exceed 60 equivalent feet.
Elbows, transitions, wall and roof
caps, etc., present additional resistance to
airflow and are equivalent to a section of straight duct
which is longer than their actual physical size. When
calculating the total duct length, add the equivalent
lengths of all transitions and adaptors plus the length
of all straight duct sections. The chart below shows
you how to calculate total equivalent ductwork length
using the approximate feet of equivalent length of
some typical ducts.
Exhaust connection:
The hood exhaust has been designed to mate with a
standard 3¼" x 10" rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less
than a 6" diameter duct.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
Rectangular-to-Round
Transition Adaptor*
5 Ft.
x
( )
=
Ft.
Wall Cap
40 Ft.
x
( )
=
Ft.
90° Elbow
10 Ft.
x
( )
=
Ft.
45° Elbow
5 Ft.
x
( )
=
Ft.
90° Elbow
25 Ft.
x
( )
=
Ft.
45° Elbow
5 Ft.
x
( )
=
Ft.
Roof Cap
24 Ft.
x
( )
=
Ft.
Straight Duct 6" Round or
3¼" x 10" Rectangular
1 Ft.
x
( )
=
Ft.
Total Ductwork
=
Ft.
* IMPORTANT: If a rectangular-toround transition adaptor is used, the
bottom corners of the damper will
have to be cut to fit, using the tin
EQUIVALENT
LENGTH
snips, in order to allow free movement of the damper.
Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.
5
A–6
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
DAMAGE – SHIPMENT/
INSTALLATION
PARTS INCLUDED
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for repair
or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
• If the unit is damaged by the installer (if other
than the customer), repair or replacement must
be made by arrangement between customer and
installer.
HARDWARE PACKET
PART
Wood Screws
(¼" x 2")
QUANTITY
1
3
Toggle Bolts
(and wing nuts)
(3/16" x 3")
Self-aligning
3
Machine Screws
(¼"-28 x 3¼")
Nylon Grommet
2
(for metal cabinets)
You will find the installation hardware contained in a
packet with the unit. Check to make sure you have all
these parts.
NOTE: Some extra parts are included.
ADDITIONAL PARTS
PART
QUANTITY
1
TOP CABINET TEMPLATE
Top Cabinet
Template
REAR WALL TEMPLATE
Rear Wall
Template
1
Installation
Instructions
1
Separately
Packed
Grease
Filters
Exhaust
adaptor
2
Installation
Instructions
1
6
© 2006 Maytag Services
16027303
A–7
Installation Instructions
Installation Instructions
TOOLS YOU WILL NEED
Ruler or tape measure
and straight edge
Pencil
# 1 and #2 Phillips screwdriver
Tin snips (for cutting
damper, if required)
Scissors
(to cut template, if necessary)
Gloves
Saw (saber, hole or keyhole)
Safety goggles
Electric drill with 3/16", ½"
and 5/8" drill bits
Duct and masking tape
MOUNTING SPACE
30"
5"
33"min.
Filler blocks or scrap wood
pieces, if needed for top
cabinet spacing (used on
recessed bottom cabinet
installations only)
Stud finder or Hammer (optional)
Level
16-½ "
Carpenter square
(optional)
Bottom edge of
cabinet needs
to be 33" or
more from the
cooking
surface
Backsplash
NOTES:
• The space between the cabinets must be
30" wide and free of obstructions.
• This microwave oven is for installation over
ranges up to 33" wide.
• If you are going to vent your microwave
oven to the outside, see Hood Exhaust
Section for exhaust duct preparation.
• When installing the microwave oven
beneath smooth flat cabinets be careful
to follow the instructions on the top
cabinet template for power cord
clearance.
7
A–8
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
1.PLACEMENT OF THE MOUNTING PLATE
A. REMOVING THE MICROWAVE
B. FINDING THE WALL STUDS
OVEN FROM THE CARTON/
REMOVING THE MOUNTING
PLATE
1. Remove the installation instructions, Exhaust
adaptor, filters, glass tray and the small hardware
bag. Do not remove the Styrofoam protecting the
front of the oven.
Wall Studs
Center
2. Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton over
onto the top side. The oven should be resting in
the Styrofoam.
1. Find the studs, using one of the following
Carton
methods:
A. Stud finder–a magnetic device which locates
nails.
OR
Styrofoam
B. Use a hammer to tap lightly across the
mounting surface to find a solid sound. This
will indicate a stud location.
2. After locating the stud(s), find the center by
3. Pull the carton up and off the oven.
4. Remove and properly discard plastic bags.
probing the wall with a small nail to find the edges
of the stud. Then place a mark halfway between
the edges. The center of any adjacent studs
should be 16" or 24" from this mark.
Screws
Screws
3. Draw a line down the center of the studs.
Mounting Plate
THE MICROWAVE MUST BE CONNECTED TO AT
LEAST ONE WALL STUD.
5. Remove the 2 screws from the mounting plate.
This plate will be used as the rear wall template
and for mounting.
NOTE: You will have to reuse two screws in original
loction of outcase after removing mounting plate.
8
© 2006 Maytag Services
16027303
A–9
Installation Instructions
Installation Instructions
C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position – beneath framed recessed
cabinet bottom
Plate position – beneath flat bottom cabinet
16-1/2²
CL
At least 30″
Draw a vertical line on
the wall at the center of
the 30″ wide space.
Tape the Rear Wall
Template onto the wall
matching the centerline
and touching the
bottom of the cabinet.
CL
33″ to Cooktop
Draw a vertical line on the wall at the center of the
30″ space.
Tape the Rear Wall Template onto the wall
matching the centerline and touching the bottom
cabinet frame.
Your cabinets may have decorative trim that
interferes with the microwave installation. Remove
the decorative trim to install the microwave properly
and to make it level.
Plate position – beneath recessed bottom
cabinet with front overhang
Draw a line on the
back wall equal to the
depth of the front
overhang.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no
back or side frame, install the mounting plate down
the same distance as the front overhang depth. This
will keep the microwave level.
1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal
CL
distance below the cabinet bottom as the inside
depth of the front overhang.
33" to Cooktop
3. For this type of installation with front overhang
only, align the mounting tabs with this horizontal
line, not touching the cabinet bottom as described
in Step D.
9
A – 10
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
D. ALIGNING THE WALL PLATE
Hole A
Draw a Vertical Line
on Wall from Center
of Top Cabinet
Centerline
notches
CL
Horizontal Line
Area E
Hole C
Hole B Horizontal Line
Draw a Horizontal line on wall from
bottom of “Rear Wall Template”.
CAUTION: Wear gloves to avoid cutting
fingers on sharp edges.
1. Draw a Vertical line on the wall at the center of the
NOTE: Holes A, B and C are inside area E. If none of
A, B and C is in a stud, find a stud somewhere in area
E and draw a forth circle to line up with the stud. It is
important to use at least one wood screw mounted
firmly in a stud to support the weight of the
microwave. Set the mounting plate aside.
30" wide space.
2. Draw a Horizontal line on the wall at the bottom of
“Rear Wall Template”.
3. Drill 5/8" holes for toggle bolts on 3 locations
(Hole A, Hole B, Hole C) but if the location of hole
is same as that of stud, drill a 3/16" hole for wood
screw. In other words, toggle bolt can not be used
to the location of stud.
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
10
© 2006 Maytag Services
16027303
A – 11
Installation Instructions
Installation Instructions
2. INSTALLATION TYPES (Choose A, B or C)
This microwave oven is designed for adaptation to
the following three types of ventilation:
A. Recirculating (Non-Vented Ductless)
B. Outside Top Exhaust (Vertical Duct)
C. Outside Back Exhaust (Horizontal Duct)
NOTE: This microwave is shipped after being
assembled for “Recirculating”. And exhaust adaptor
is shipped assembled to the filler-upper. Select the
type of ventilation required for your installation and
proceed to that section.
A. RECIRCULATING
B. OUTSIDE TOP EXHAUST
(NON-VENTED DUCTLESS)
(VERTICAL DUCT)
Adaptor in Place for
Outside Top
Exhaust
See page 12
See page 14
C. OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
See page 18
11
A – 12
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
A. RECIRCULATING (Non-Vented Ductless)
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Mount the Microwave Oven
A1. ATTACH THE MOUNTING PLATE
3. Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure to coincide bottom line of the
Mounting plate with Horizontal line of “Rear wall
Template” and then the Mounting plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
TO THE WALL
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
A2. USE TOP CABINET TEMPLATE
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach the plate to
a wall stud.
FOR PREPARATION OF TOP
CABINET
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
the holes designated to go into drywall and
reattach the toggle wings to ¾ " onto each bolt.
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
Toggle Wings
Toggle
Bolt
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
Wall
Bolt End
12
© 2006 Maytag Services
16027303
A – 13
Installation Instructions
Installation Instructions
A3. MOUNT THE MICROWAVE OVEN
especially when mounting flush to bottom of
cabinet.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of
Cabinet Recess
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
Self-Aligning Screw
Microwave Oven Top
4. Attach the microwave oven to the top cabinet.
5. Insert 2 self-aligning screws through outer
top cabinet holes. Turn two full turns on
each screw.
1. Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.
6. Tighten center
screw completely.
7. Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
2. Rotate front of oven
up against cabinet
bottom
3. Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
8. Install grease filters. See the Owner’s Manual
packed with the microwave.
13
A – 14
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
B. OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
B1. Attach Mounting Plate to Wall
B2. Prepare Top Cabinet
B3. Adjust Blower
B4. Check Damper Operation
B5. Mount Microwave Oven
B6. Adjust Exhaust Adaptor
B7. Connect Ductwork
B1. ATTACH THE MOUNTING PLATE
To use toggle bolts:
TO THE WALL
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
Toggle Wings
Toggle
Bolt
Wall
Bolt End
3. Place the mounting plate against the wall and
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach
the plate to a wall stud.
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure to coincide bottom line of the
Mounting plate with Horizontal line of “Rear wall
Template” and then the Mounting plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the
holes designated to go into drywall and reattach
the toggle wings to ¾" onto each bolt.
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
14
© 2006 Maytag Services
16027303
A – 15
Installation Instructions
Installation Instructions
B3. ADAPTING MICROWAVE
B2. USE TOP CABINET TEMPLATE
BLOWER FOR OUTSIDE TOP
EXHAUST
FOR PREPARATION OF TOP
CABINET
1. Remove and save
You need to drill holes for the top support screws, a
hole large enough for the power cord to fit through,
and a cutout large enough for the exhaust adaptor.
2. Lift up the
screw that holds
blower plate to
microwave.
blower plate.
Blower Plate
Back of
Microwave
Screw
3. Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
CAUTION: Do not touch blade of blower to prevent
cracking and breaking. Hold outer case when the
blower is removed and re-installed.
4. Roll the blower unit 90° so that fan blade
openings are facing toward the top of the
microwave.
BEFORE: Fan Blade
Openings Facing Forward
Roll
15
A – 16
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
B5. MOUNT THE MICROWAVE OVEN
AFTER: Fan Blade Openings
Facing Upward
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
5. Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
6. Secure blower unit to microwave with the screw.
1. Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.
B4. INSTALLATION PROCEDURE FOR
EXHAUST ADAPTOR AND
PROPER DAMPER OPERATION
CHECK
1. Remove and save screw
from the panel-outer
2. Rotate front of oven up
against cabinet bottom
3. Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
especially when mounting flush to bottom of
cabinet.
Exhaust Adaptor and Damper is shipped
after being assembled to the filler-upper.
2. Slide exhaust adaptor following the instructions
show in diagram.
3. Make sure tape securing damper is removed and
damper pivots easily before mounting microwave.
4. Lift damper and Re-screw at same location as (1).
• You will need to make adjustments to assure
proper alignment with your house exhaust duct
after the microwave is installed.
16
© 2006 Maytag Services
16027303
A – 17
Installation Instructions
Installation Instructions
B5. MOUNT THE MICROWAVE OVEN
B6. ADJUST THE EXHAUST ADAPTOR
(cont.)
Open the top cabinet and adjust the exhaust adaptor
to connect to the house duct.
Cabinet Front
Cabinet Bottom Shelf
Blower-Plate
Filler Block
Back of
Microwave
Damper
Equivalent to
Depth of Cabinet
Recess
For Front-to-Back
Adjustment, Slide the
Exhaust Adaptor as
Needed
Self-Aligning Screw
Microwave Oven Top
4. Attach the microwave oven to the top cabinet.
5. Insert 2 self-aligning screws
B7. CONNECTING DUCTWORK
through outer top cabinet holes.
Turn two full turns on each screw.
House Duct
6. Tighten center screw
completely.
7. Tighten the outer two screws to the top of the
1. Extend the house duct down to connect to the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
exhaust adaptor.
2. Seal exhaust duct joints using duct tape.
8. Install grease filters. See the Owner’s Manual
packed with the microwave.
17
A – 18
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
C. OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW
C1. Prepare Rear Wall
C2. Attach Mounting Plate to Wall
C3. Prepare Top Cabinet
C4. Adjust Blower
C5. Mount the Microwave Oven
C1. PREPARING THE REAR WALL
C2. ATTACH THE MOUNTING PLATE
FOR OUTSIDE BACK EXHAUST
TO THE WALL
You need to cut an opening in the rear wall for outside
exhaust.
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach
the plate to a wall stud.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through
CL
the holes designated to go into drywall and
reattach the toggle wings to ¾ " onto each bolt.
• Read the instructions on the REAR WALL
TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
18
© 2006 Maytag Services
16027303
A – 19
Installation Instructions
Installation Instructions
C2. ATTACH THE MOUNTING PLATE
C4. ADAPTING MICROWAVE BLOWER
TO THE WALL (cont.)
FOR OUTSIDE BACK EXHAUST
1. Remove and save screw that holds blower Plate
To use toggle bolts:
to microwave.
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
Blower motor
screw.
Toggle Wings
Toggle
Bolt
2. Lift up the Blower Plate.
Blower Motor
Back of
Microwave
Wall
Bolt End
Blower Motor
Screw
3. Place the mounting plate against the wall and
3. Carefully pull out the blower unit. The wires will
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure to coincide bottom line of the
Mounting plate with Horizontal line of “Rear wall
Template” and then the Mounting plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
extend far enough to allow you to adjust the
blower unit.
BEFORE: Fan Blade
Openings Facing Forward
End B
End A
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
CAUTION: Do not touch blade of blower to prevent
cracking and breaking. Hold outer case when the
blower is removed and re-installed.
C3. USE TOP CABINET TEMPLATE
4. Remove “Parts “A” with Nipper or Scissors
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
Knockouts
Parts”A”
5. Rotate blower unit counterclockwise 180°.
Before Rotation
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in
the cabinet bottom.
Back of
Microwave
After Rotation
Back of
Microwave
19
A – 20
16027303
© 2006 Maytag Services
Installation Instructions
Installation Instructions
6. Place the blower unit back into the opening.
C5. MOUNT THE MICROWAVE OVEN
AFTER: Fan Blade
Openings Facing Back
End A
End B
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should
match exhaust openings on rear of microwave
oven.
7. Secure the blower unit to the microwave with the
screw.
Blower-Plate
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
1. Lift microwave, tilt it
From the Mounting
Plate screw
Back of
Microwave
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.
8. Attach the exhaust adaptor to the rear of the oven
by sliding it into the guides at the top center of the
back of the oven.
Adaptor
2. Rotate front of oven
Back of
Microwave
up against cabinet
bottom
3. Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
especially when mounting flush to bottom of
cabinet.
Guide
Guide
From Blower motor screw
(after attached the exhaust adaptor)
Push in securely until it is in the lower locking tabs.
Take care to assure that the damper hinge is installed
so that it is at the top and that the damper swings
freely.
20
© 2006 Maytag Services
16027303
A – 21
Installation Instructions
Installation Instructions
C5. MOUNT THE MICROWAVE OVEN
(cont.)
Install grease filters. See the Owner’s Manual packed
with the microwave.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of Cabinet
Recess
Self-Aligning Screw
Microwave Oven Top
4. Attach the microwave oven to the top cabinet.
5. Insert 2 self-aligning screws
through outer top cabinet holes.
Turn two full turns on each screw.
6. Tighten center
screw completely.
7. Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
8. Install grease filters. See the Owner’s Manual
packed with the microwave.
21
A – 22
16027303
© 2006 Maytag Services
Appendix B
The Use and Care information provided in this service manual is representative of a limited
number of models. Reference the customer’s Use and Care literature included with the
product, order a copy (if needed), or consult Jenn-Air’s website for the specific model.
www.maytag.com or www.amana.com or www.jennair.com
© 2006 Maytag Services
16027303
B–1
Use and Care
2YHU7KH5DQJH
0LFURZDYH2YHQ
8VH&DUH*XLGH
-ODEL*-6"!
+EEPINSTRUCTIONSFORFUTUREREFERENCE
"ESURE5SE#ARE'UIDESTAYSWITHOVEN
3DUW1R3
&RGH1R'(-
)RUP1R$
B–2
16027303
© 2006 Maytag Services
Use and Care
)HDWXUHV
/6%.30%#)&)#!4)/.3
-ODELAND3ERIAL
.UMBER0LATE
7INDOWWITH
-ETAL3HIELD #OOKING
$OOR(ANDLE
'UIDE
6ENT'RILLE
'LASS4URNTABLE
,OWRACK
#ONVECTIONOR#OMBINATION
- EDIUMRACK
#ONVECTION#OMBINATIONOR"ROILING
(IGHRACK
"ROILING/NLY
$OOR3AFETY
,OCK3YSTEM
0OWER3UPPLY
6!#(Z
)NPUT0OWER
753!
#OOKING
0OWER
7
)%#
3TANDARD
&REQUENCY
-(Z
2ATED#URRENT
!53!
7X
/UTER
$IMENSIONS
/VEN#ONTROL
0ANEL
$RIPPAN
(X
$
#AVITY6OLUME #U&T
s3EEPAGESAND
.ET7EIGHT
LBS
© 2006 Maytag Services
16027303
B–3
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
,%!2.!"/549/52
-)#2/7!6%/6%.
4HISSECTIONINTRODUCESYOUTOTHE
BASICSYOUNEEDTOKNOWTOOPERATE
YOURMICROWAVEOVEN0LEASEREAD
THISINFORMATIONBEFOREUSE
#!54)/.
s4OAVOIDRISKOFPERSONALINJURYOR
PROPERTYDAMAGEDONOTRUNOVEN
EMPTY
s4OAVOIDRISKOFPERSONALINJURY
ORPROPERTYDAMAGEDONOTUSE
STONEWAREALUMINUMFOILMETAL
UTENSILSORMETALTRIMMEDUTENSILS
INTHEOVEN
#,/#+
%XAMPLE4OSET!-
4OUCH#,/#+PAD
%NTERTHETIMEBY
USINGTHENUMBER
PADS
.O
&UNCTION
.O
2ESULT
7EIGHTMODE
SELECTED
,BS
+G
3OUND/./&& CONTROL
3OUND/.
3OUND/&&
#LOCKDISPLAY
CONTROL
(2
(2
$ISPLAY
3LOWSPEED
.ORMAL
SPEED
&ASTSPEED
2EMINDEND
3IGNAL
/.
/&&
$EMO-ODE
/.
/&&
$AYLIGHT
3AVING4IME
/.
/&&
%XAMPLE4OCHANGEWEIGHTMODE
FROM,BSTO+G
4OUCH#/.42/,
3%450PAD
4OUCHNUMBER
PAD
4OUCHFOR!-
4OUCHNUMBER
PAD
./4%
s&OLLOWSTEPSABOVEINTHE
HOURCLOCKMODE
+)4#(%.4)-%2
9OUCANUSEYOURMICROWAVEOVEN
ASATIMER5SETHE+ITCHEN4IMERFOR
TIMINGUPTOMINUTESSECONDS
%XAMPLE4OSETFORMINUTES
4OUCH+)4#(%.
4)-%2PAD
9OUCANCHANGETHEDEFAULTVALUES
3EEFOLLOWINGCHARTFORMOREINFORMATION
4OUCH%.4%2
34!24PAD
4OUCH%.4%2
34!24PAD
#/.42/,3%450
%NTERTHETIMEBY
USINGTHENUMBER
PADS
4OUCH%.4%2
34!24PAD
6%.4&!.
4HE6%.4MOVESSTEAMANDOTHER
VAPORSFROMTHECOOKINGSURFACE
4HEVENTWILLOPERATEATTHE,%6%,
WHENEVERTHEOVENISON
%XAMPLE4OSET,EVEL
4OUCH/./&&PAD
4HISSHOWSTHELAST
LEVELUNTILYOUSELECT
THEFANSPEEDLEVEL
./4%
s)FTHETEMPERATUREGETSTOOHOT
AROUNDTHEMICROWAVEOVENTHEFAN
INTHEVENTHOODWILLAUTOMATICALLY
TURNONATTHE,%6%,SETTING
TOCOOLTHEOVEN4HEFANWILL
AUTOMATICALLYTURNOFFWHENTHE
INTERNALPARTSARECOOL7HENTHIS
OCCURSTHEVENTCANNOTBETURNED
OFF
$%,!9/&&
%XAMPLE4OTURNOFFFANAFTER
MINUTESFOR,EVEL
4OUCH/./&&PAD
4OUCH30%%$PAD
UNTIL,EVELAPPEARS
INTHEDISPLAY
4OUCH$%,!9/&&
PADFIVETIMES
452.4!",%/./&&
&ORBESTCOOKINGRESULTSLEAVETHE
TURNTABLEON)TCANBETURNEDOFFFOR
LARGEDISHES
4OUCH452.4!",%
/./&&PADTOTURN
THETURNTABLEONOROFF
./4%3
s4HISOPTIONISNOTAVAILABLEIN
SENSORCOOKAUTOCOOKAND
DEFROSTMODES
s3OMETIMESTHETURNTABLECAN
BECOMEHOTTOTOUCH"ECAREFUL
TOUCHINGTHETURNTABLEDURINGAND
AFTERCOOKING
s$ONOTRUNTHEOVENEMPTY
4OUCH30%%$PAD
UNTIL,EVELAPPEARS
INTHEDISPLAY
4OUCH/./&&PADTOTURNOFFFAN
WHENDESIRED
7HENTHETIMEISOVERYOUWILLHEAR
BEEPSAND%.$WILLDISPLAY
B–4
16027303
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
#(),$,/#+
,)'(44)-%2
-/2%,%33
9OUMAYLOCKTHECONTROLPANELTO
PREVENTTHEMICROWAVEFROMBEING
ACCIDENTALLYSTARTEDORUSEDBY
CHILDREN
4HE#HILD,OCKFEATUREISALSOUSEFUL
WHENCLEANINGTHECONTROLPANEL
#HILD,OCKPREVENTSACCIDENTAL
PROGRAMMINGWHENWIPINGTHECONTROL
PANEL
%XAMPLE4OSETTHECHILDLOCK
9OUCANSETTHE,)'(4TOTURNON
ANDOFFAUTOMATICALLYATANYTIME
4HELIGHTCOMESONATTHESAMETIME
EVERYDAYUNTILRESET
%XAMPLE4URNON!-TURN
OFF0-
HOURCLOCKMODE
4HE-ORE,ESSPADSALLOW
YOUTOADJUSTPRESETCOOKINGTIMES
4HEYONLYWORKINTHE3ENSOR2EHEAT
3ENSOR#OOKINGEXCEPT"EVERAGE
!DDSEC#USTOM#OOKOR4IME
#OOKMODES5SETHE-ORE
,ESSPADSONLYAFTERYOUHAVE
ALREADYBEGUNCOOKINGWITHONEOF
THESEPROCEDURES
4OUCH,)'(44)-%2
PAD
OUCHANDHOLD
4
%.4%234!24PAD
MORETHANSECONDS
#(),$,/#+/.WILL
APPEARINTHEDISPLAY
WINDOWWITHTWO
BEEPS
%XAMPLE4OCANCELTHECHILDLOCK
OUCHANDHOLD
4
%.4%234!24
PADMORETHAN
SECONDS,/#+%$
WILLDISAPPEARANDYOU
HEARTWOBEEPS
,)'(4(),//&&
4OUCH,)'(4(),/
/&&PADONCEFOR
BRIGHTLIGHTTWICEFOR
NIGHTLIGHTORTHREE
TIMESTOTURNTHELIGHT
OFF
%NTERTHETIMEYOU
WANTTHE,)'(4TO
TURNON
4OUCH%.4%2
34!24PAD
4OUCHFOR!-
4OUCH%.4%2
34!24PAD
4OUCH!$$3%#
PADTIMES4HEOVEN
BEGINSCOOKINGAND
DISPLAYSHOWSTIME
COUNTINGDOWN
4O2%$5#%THE
TIMEOFANAUTOMATIC
COOKINGPROCEDURE
4OUCHTHE,ESS
PAD
%NTERTHETIMEYOU
WANTTHE,)'(4TO
TURNOFF
4OUCH%.4%2
34!24PAD
4OUCHFOR0-
4OUCH%.4%2
34!24PAD
HOURCLOCKMODE
4OUCH,)'(4
4)-%2PAD
%NTERTHETIMEYOU
WANTTHE,)'(4TO
TURNON
!$$3%#
!TIMESAVINGPADTHISSIMPLIFIED
CONTROLLETSYOUQUICKLYSETANDSTART
MICROWAVECOOKINGWITHOUTTHENEED
TOTOUCHTHE%.4%234!24PAD
%XAMPLE4OSET!$$3%#FOR
MINUTES
4O!$$MORETIMETO
ANAUTOMATICCOOKING
PROCEDURE4OUCHTHE
-OREPAD
4OUCH%.4%2
34!24PAD
%NTERTHETIMEYOU
WANTTHE,)'(4TO
TURNOFF
4OUCH%.4%2
34!24PAD
%XAMPLE4OCANCELTHE,)'(4
4)-%2
4OUCH,)'(44)-%2
PAD
4OUCHPAD
© 2006 Maytag Services
16027303
B–5
Use and Care
Models AMC4080AA*, MMC5080AA*
2SHUDWLQJ,QVWUXFWLRQV
#//+).'!4()'(
0/7%2,%6%,3
#//+).'!4,/7%2
0/7%2,%6%,3
%XAMPLE4OCOOKFOODFOR
MINUTESSECONDSATPOWER
()'(POWERCOOKINGDOESNOTALWAYS
GIVEYOUTHEBESTRESULTSWITHFOODS
THATNEEDSLOWERCOOKINGSUCHAS
ROASTSBAKEDGOODSORCUSTARDS
9OUROVENHASPOWERSETTINGSIN
ADDITIONTO()'(
%XAMPLE4OCOOKFOODFOR
MINUTESSECONDSATPOWER
%NTERTHECOOKTIME
4OUCH%.4%2
34!24PAD
7HENTHECOOKTIMEISOVERYOU
WILLHEARFOURBEEPSAND%.$WILL
DISPLAY
%NTERTHECOOKTIME
4OUCH0/7%2
,%6%,PAD
%NTERTHEPOWER
LEVEL
4OUCH%.4%2
34!24PAD
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
3EECOOKINGGUIDEFOR0OWERLEVELS
PAGE
)-0/24!.4
s$/./4STOREORUSETHEWIRE
RACKINTHISOVENUNLESSMORE
THANONEITEMISBEINGCOOKEDOR
ARECIPECALLSFORIT
s$AMAGETOTHEOVENCOULDOCCUR
B–6
16027303
#//+).'7)4(
-/2%4(!./.%
#//+#9#,%
&ORBESTRESULTSSOMERECIPESCALLFOR
ONE0OWER,EVELFORACERTAINLENGTH
OFTIMEANDANOTHER0OWER,EVELFOR
ANOTHERLENGTHOFTIME9OUROVENCAN
BESETTOCHANGEFROMONETOANOTHER
AUTOMATICALLYFORUPTOTHREECYCLESIF
THEFIRSTCYCLEISDEFROST
%XAMPLE4OCOOKFOODFOR
MINUTESATPOWERANDTHEN
POWERFORMINUTES
SECONDS
%NTERTHEFIRSTCOOK
TIME
4OUCH0/7%2
,%6%,PAD
%NTERTHEPOWER
LEVEL
%NTERTHESECOND
COOKTIME
4OUCH0/7%2
,%6%,PAD
%NTERTHEPOWER
LEVEL
4OUCH%.4%2
34!24PAD
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
3%.3/2/0%2!4).'
).3425#4)/.3
3ENSOR#OOKALLOWSYOUTOCOOK
MOSTOFYOURFAVORITEFOODSWITHOUT
SELECTINGCOOKINGTIMESANDPOWER
LEVELS4HEDISPLAYWILLINDICATETHE
SENSINGPERIODBYSCROLLINGTHENAME
OFTHEFOOD4HEOVENAUTOMATICALLY
DETERMINESREQUIREDCOOKINGTIMEFOR
EACHFOODITEM7HENTHEINTERNAL
SENSORDETECTSACERTAINAMOUNTOF
HUMIDITYCOMINGFROMTHEFOODIT
WILLTELLTHEOVENHOWMUCHLONGER
TOCOOK4HEDISPLAYWILLSHOWTHE
REMAININGHEATINGTIME
&ORBESTRESULTSWHENCOOKING
BY3ENSORFOLLOWTHESE
RECOMMENDATIONS
&OODCOOKEDWITHTHESENSOR
SYSTEMSHOULDBEATNORMAL
STORAGETEMPERATURE
'LASSTURNTABLEANDOUTSIDEOF
CONTAINERSHOULDBEDRYTOASSURE
BESTCOOKINGRESULTS
-OSTFOODSSHOULDALWAYSBE
COVEREDLOOSELYWITHMICROWAVABLE
PLASTICWRAPWAXEDPAPERORALID
$ONOTOPENTHEDOORORTOUCH
THE34/0#,%!2PADDURINGTHE
SENSINGTIME7HENSENSINGTIME
ISOVERTHEOVENBEEPSANDTHE
REMAININGCOOKINGTIMEWILLAPPEAR
INTHEDISPLAYWINDOW!TTHISTIME
YOUCANOPENTHEDOORTOSTIRTURN
ORREARRANGETHEFOOD
)-0/24!.4
7HENUSINGSENSORCOOKTHEOVEN
MUSTCOOLFORMINUTESBETWEEN
USESORFOODWILLNOTCOOKPROPERLY
-ATCHTHEAMOUNTTOTHESIZEOFTHE
CONTAINER&ILLCONTAINERSATLEAST
HALFFULLFORBESTRESULTS
"ESURETHEOUTSIDEOFTHECOOKING
CONTAINERANDTHEINSIDEOFTHE
MICROWAVEOVENAREDRYBEFORE
PLACINGFOODINTHEOVEN"EADSOF
MOISTURETURNINGINTOSTEAMCAN
MISLEADTHESENSOR
!$$).'/2
35"42!#4).'
#//+4)-%
"YUSINGTHE-OREOR,ESS
PADSALLOFTHESENSORCOOKANDTIME
COOKSETTINGSCANBEADJUSTEDTOCOOK
FOODFORALONGERORSHORTERTIME
#!54)/.
s$/./4LEAVEMICROWAVE
UNATTENDEDWHILEPOPPINGCORN
s$/./4USETHEWIRERACKWHEN
POPPINGCOMMERCIALLYPACKAGED
POPCORN
0)::!3,)#%
2EHEATINGPIZZAWITH0)::!3,)#%
PADLETSYOUREHEATONEORSEVERAL
SLICESOFPIZZAWITHOUTSELECTING
COOKINGTIMESANDPOWERLEVELS
%XAMPLE4OREHEATSLICESOF
PIZZA
4OUCH0)::!3,)#%
PAD
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
s2ECOMMENDEDAMOUNTSSLICES
./4%
)FFOODISNOTTHOROUGHLYCOOKEDOR
REHEATEDWHENUSINGTHESENSOR
FEATURECOMPLETEUSINGAPOWER
LEVELANDCOOKINGTIME$/./4
CONTINUEUSINGTHESENSORPAD
0/0#/2.
0/0#/2.PADLETSYOUPOP
COMMERCIALLYPACKAGEDMICROWAVE
POPCORN0OPONLYONEPACKAGEATA
TIME&ORBESTRESULTSUSEFRESHBAGS
OFPOPCORN
%XAMPLE4OPOPPOPCORN
OUCH0/0#/2.
4
PAD
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
s2ECOMMENDEDAMOUNTS
OZS
3%.3/2#//+).'
'5)$%
!PPROPRIATECONTAINERSANDCOVERINGS
HELPASSUREGOOD3ENSORCOOKING
RESULTS
!LWAYSUSEMICROWAVABLECON
TAINERSANDCOVERTHEMWITHLIDSOR
VENTEDPLASTICWRAP
.EVERUSETIGHTSEALINGPLASTIC
COVERS4HEYCANPREVENTSTEAM
FROMESCAPINGANDCAUSEFOODTO
OVERCOOK
© 2006 Maytag Services
16027303
B–7
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
"!+%$0/4!4/
3%.3/2#//+
2%(%!4
4HE"!+%$0/4!4/PADLETSYOU
BAKEONETOSIXPOTATOESWITHOUT
SELECTINGCOOKINGTIMESANDPOWER
LEVELS
5SING3%.3/2#//+PADLETSYOU
HEATCOMMONMICROWAVEPREPARED
FOODSWITHOUTNEEDINGTOPROGRAM
COOKINGTIMESANDPOWERLEVELS
3%.3/2#//+HASPRESETFOOD
CATEGORIES&ROZEN6EGETABLE
&ROZEN"REAKFAST&ROZEN$INNER
&RESH6EGETABLESHRIMP
%XAMPLE4OCOOK&ROZEN$INNER
2%(%!4PADLETSYOUHEATFOODS
WITHOUTNEEDINGTOPROGRAMCOOKING
TIMESANDPOWERLEVELS2%(%!4HAS
PRESETCATEGORIES$INNER0LATE
#ASSEROLEAND0ASTA
%XAMPLE4OREHEAT#ASSEROLE
./4%3
s#OOKINGTIMEISBASEDONA
OZPOTATO
s5SETHE-ORE,ESSPADS
IFCOOKINGLARGERORSMALLER
POTATOES
s"EFOREBAKINGPIERCEPOTATOWITH
FORKSEVERALTIMES
s)FPOTATOISNOTCOMPLETELYCOOKED
USE#OOKING4IME$/./4USE
"!+%$0/4!4/PADTOCOMPLETE
COOKING
!FTERBAKINGLETSTANDFORMINUTES
%XAMPLE4OCOOKPOTATOES
4OUCH"!+%$
0/4!4/PAD
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
2ECOMMENDEDAMOUNTS
POTATOES
4OUCH2%(%!4
PAD
#HOOSEFOOD
CATEGORY
4OUCH3%.3/2
#//+PAD
#HOOSEFOOD
CATEGORY
4OUCH0AD
.UMBER
#ATEGORY
&ROZEN6EGETABLE
&ROZEN"REAKFAST
&ROZEN$INNER
&RESH6EGETABLE
3HRIMP
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
#ATEGORY
4OUCH0AD
.UMBER
$INNER0LATE
#ASSEROLE
0ASTA
7HENTHECOOKTIMEISOVERYOUWILL
HEARFOURBEEPSAND%.$WILLDISPLAY
2ECOMMENDEDAMOUNTS
$INNER0LATE
SERVING
#ASSEROLE
SERVINGS
0ASTA
SEVINGS
2ECOMMENDEDAMOUNTS
B–8
&ROZEN6EGETABLE
3ERVINGS
&ROZEN"REAKFAST
OZS
&ROZEN$INNER
OZS
&RESH6EGETABLE
3ERVINGS
3HRIMP
OZS
16027303
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
3%.3/2#//+4!",%
#!4%'/29
$)2%#4)/.3
!-/5.4
5SEONLYONEMICROWAVEONLYBAGOFPOPCORNATATIME5SECAUTIONWHENREMOVINGAND
OPENINGTHEHOTBAGFROMOVEN,ETOVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN
TOOZ
PACKAGE
"AKED0OTATO
0RICKEACHPOTATOSEVERALTIMESWITHFORK0LACEONTURNTABLEINSPOKELIKEFASHION,ET
STANDMINUTES,ETOVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN5SE-ORE
PADWHENCOOKINGLARGERPOTATOES
TOPOTATOES
0IZZA3LICE
0UTSLICESOFPIZZAONA-ICROWAVESAFEPLATEWITHWIDEENDOFSLICETOWARDTHEOUTSIDE
EDGEOFTHEPLATE$ONOTLETSLICESOVERLAP$ONOTCOVER,ETOVENCOOLFORATLEAST
MINUTESBEFOREUSINGAGAIN5SE-OREPADTOINCREASEREHEATTIMEFORTHICKCRUST
PIZZA
TO3LICES
&ROZEN
6EGETABLES
0LACEFROZENVEGETABLESINMICROWAVESAFECERAMICGLASSORPLASTICDISHANDADD
4BSWATER#OVERWITHLIDORVENTEDPLASTICWRAPDURINGCOOKINGANDSTIRBEFORESTANDING
,ETOVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN5SETHE-OREPADWHEN
COOKINGDENSEVEGETABLESSUCHASCARROTSORBROCCOLISPEARS
TOSERVINGS
&ROZEN
"REAKFAST
&OLLOWPACKAGEINSTRUCTIONSFORCOVERINGANDSTANDING5SETHISPADFORFROZENSANDWICH
BREAKFASTENTREEETC,ETOVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN
TOOZ
&ROZEN
$INNER
2EMOVEFOODFROMOUTERWRAPPINGANDFOLLOWBOXINSTRUCTIONSFORCOVERINGANDSTANDING
,ETOVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN
TOOZ
&RESH
6EGETABLES
0LACEFRESHVEGETABLESINMICROWAVESAFECERAMICGLASSORPLASTICDISHANDADD4BS
WATER#OVERWITHLIDORVENTEDPLASTICWRAPDURINGCOOKINGANDSTIRBEFORESTANDING,ET
OVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN5SETHE-OREPADWHENCOOKING
DENSEVEGETABLESSUCHASCARROTSORBROCCOLISPEARS
TOSERVINGS
3HRIMP
!RRANGESHRIMPINAMICROWAVESAFECERAMICGLASSORPLASTICDISHANDADD4BSMELTED
BUTTER#OVERWITHLIDORVENTEDPLASTICWRAPDURINGCOOKINGANDSTIRBEFORESERVING,ET
STANDMINUTES,ETOVENCOOLATLEASTMINUTESBEFOREUSINGAGAIN
TOOZ
#//+
0OPCORN
3%.3/22%(%!44!",%
#!4%'/29
$INNER0LATE
#ASSEROLE
0ASTA
$)2%#4)/.3
!-/5.4
5SEONLYPRECOOKEDREFRIGERATEDFOODS#OVERPLATEWITHVENTEDPLASTICWRAPOR
WAXEDPAPERTUCKEDUNDERPLATE)FFOODISNOTASHOTASYOUPREFERAFTERHEATING
WITH3%.3/22%(%!4CONTINUEHEATINGUSINGCOOKINGTIMEANDPOWERLEVEL
$ONOTCONTINUECOOKINGUSINGTHE2EHEATPAD
#ONTENTS
OZMEATPOULTRYORFISHUPTOOZWITHBONE
CUPSTARCHPOTATOESPASTARICEETC
CUPVEGETABLESABOUTOZ
SERVING
PLATE
#OVERPLATEWITHLIDORVENTEDPLASTICWRAP)FFOODISNOTASHOTASYOUPREFERAFTER
HEATINGWITH3%.3/22%(%!4CONTINUEHEATINGUSINGTIMEANDPOWERLEVEL$O
NOTCONTINUECOOKINGUSINGTHE2EHEATPAD
3TIRFOODSONCEBEFORESERVING
#ONTENTS
#ASSEROLEREFRIGERATEDFOODS%XAMPLES,ASAGNAANDBEEFSTEW
0ASTA#ANNEDSPAGHETTIANDRAVIOLIREFRIGERATEDFOODS
TOSERVINGS
./4%
$ESIREDFOODTEMPERATUREVARIESFROMPERSONTOPERSON5SETHE-ORE,ESSPADSTOFITYOURTEMPERATURE
PREFERENCE
© 2006 Maytag Services
16027303
B–9
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
!54/#//+
!54/#//+PADPROVIDESFIVEPRESETCATEGORIESFORCOOKING
%XAMPLE4O#OOKOZSOFBABYFOOD
4OUCH!54/#//+PADONCE
#ATEGORY
4OUCHPADNUMBER
#HOOSEFOODCATEGORY
"ABY&OOD
4OUCH%.4%234!24PAD
"EVERAGE
&ROZEN3ANDWICH
"ACON
)NSTANT2ICE
7HENTHECOOKTIMEISOVERYOUWILLHEARFOURBEEPSAND%NDWILLDISPLAY
!54/#//+4!",%
#!4%'/29
$)2%#4)/.3
!-/5.4
"ABY&OOD
2EMOVELIDFROMBABYFOODANDPLACEINTHECENTEROFOVEN#HECKTEMPERATURE
ANDSTIRWELLBEFORESERVING4HE-ORE,ESSPADSCANNOTBEUSEDWITHTHE
BABYFOOD&OLLOWMANUFACTURERgSINSTRUCTIONSSOMEBABYFOODSHOULDNOTBE
HEATEDINTHEMICROWAVEOVEN
OZS
"EVERAGE
5SEMEASURINGCUPORMUGDONOTCOVER0LACETHEBEVERAGEINTHEOVEN!FTER
HEATINGSTIRWELL,ETOVENCOOLFORATLEASTMINUTESBEFOREUSINGAGAIN
.OTEs2EHEATTIMESBASEDONANOUNCECUP
s"EVERAGEHEATEDWITHTHEBEVERAGEFEATUREMAYBEVERYHOT
s2EMOVECONTAINERWITHCARE
CUP
CUP
CUPS
&ROZEN
3ANDWICH
0LACEFROZENSANDWICHINSUSCEPTORSLEEVEWHICHISINPACKAGEANDPUTON
PLATE
%!
"ACON
0LACEPAPERTOWELSONPLATEANDARRANGEBACONONTOWELSDONOTOVERLAP
#OVERWITHADDITONALPAPERTOWEL2EMOVEPAPERTOWELIMMEDIATELYAFTERCOOKING
5SE-ORE,ESSPADSFORDESIREDCRISPNESS
SLICES
)NSTANT2ICE
&OLLOWMICROWAVEPACKAGEPREPARATIONINSTRUCTIONS5SEALARGEMICROWAVESAFE
COOKWARETOPREVENTBOILOVER
SERVINGS
./4%
$ESIREDFOODTEMPERATUREVARIESFROMPERSONTOPERSON5SETHE-ORE,ESSPADSTOFITYOURTEMPERATURE
PREFERENCE
B – 10
16027303
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
!54/$%&2/34
4OUCH
PAD.O
$EFROSTCHOICESAREPRESETINTHEOVEN4HEDEFROSTFEATURE
PROVIDESYOUWITHTHEBESTDEFROSTINGMETHODFORFROZEN
FOODSBECAUSETHEOVENAUTOMATICALLYSETSTHEDEFROSTING
TIMESACCORDINGTOTHEWEIGHTYOUENTER&ORADDED
CONVENIENCETHE!54/$%&2/34BEEPSTOREMINDYOU
TOCHECKORTURNOVERTHEFOODDURINGTHEDEFROSTCYCLE
!FTERTOUCHINGTHE!54/$%&2/34PADONCESELECTTHE
FOODWEIGHT!VAILABLEWEIGHTRANGESARETOLBS
%XAMPLE4ODEFROSTLBSOFMEAT
&OOD
&)3(
3TANDARD
!MOUNT
!FTEREACHSTAGEREARRANGE
THEFOOD)FTHEREAREANY
WARMORTHAWEDPORTIONSOF
FOODSHIELDTHEMWITHNARROW
LBS FLATPIECESOFALUMINUMFOIL
2EMOVEANYPIECESOFFOOD
THATARENEARLYDEFROSTED
,ETSTANDCOVEREDFOR
MINUTES
LBS
!RRANGEROLLSINACIRCLE
HORIZONTALLYONPAPERTOWELS
INTHEMIDDLEOFTURNTABLE
4URNOVERAFTERHALFOFTHE
DEFROSTINGTIME
LB
!FTEREACHSTAGEREMOVEANY
PIECESOFFOODTHATARENEARLY
DEFROSTED,ETSTANDCOVERD
WITHFOILFORMINUTES
4OUCH!54/$%&2/34PAD
%NTERTHEWEIGHT
"2%!$
'2/5.$
"%%&
4OUCH%.4%234!24PAD
./4%3
s!FTERYOUTOUCH%.4%234!24PADTHEDISPLAY
COUNTSDOWNTHEDEFROSTTIME4HEOVENWILLBEEPTWICE
DURINGTHE$EFROSTCYCLE!TTHISTIMEOPENTHEDOOR
ANDTURNTHEFOODASNEEDED2EMOVEANYPORTIONS
THATHAVETHAWEDTHENRETURNFROZENPORTIONSTOTHE
OVENANDTOUCH%.4%234!24PADTORESUMETHE
DEFROSTCYCLE
s4HEOVENWILLNOTSTOPDURINGTHE"%%0UNLESSTHE
DOORISOPENED
$%&2/34).''5)$%
s&OLLOWTHEINSTRUCTIONSBELOWWHENDEFROSTINGDIFFERENT
TYPESOFFOOD
4OUCH
PAD.O
&OOD
3TANDARD
!MOUNT
0ROCEDURE
-%!4
3TARTWITHTHEFOODPLACED
FATSIDEDOWN!FTEREACH
STAGETURNTHEFOODOVERAND
LBS SHIELDANYWARMPORTIONSWITH
NARROWSTRIPSOFALUMINUM
FOIL,ETSTANDCOVEREDFOR
TOMINUTES
0/5,429
!FTEREACHSTAGEREARRANGE
THEFOOD)FTHEREAREANY
WARMORTHAWEDPORTIONSOF
FOODSHIELDTHEMWITHNARROW
LBS FLATPIECESOFALUMINUMFOIL
2EMOVEANYPIECESOFFOOD
THATARENEARLYDEFROSTED
,ETSTANDCOVEREDFOR
MINUTES
© 2006 Maytag Services
0ROCEDURE
$%&2/344)03
s7HENUSING!54/$%&2/34THEWEIGHTTOBEENTERED
ISTHENETWEIGHTINPOUNDSANDTENTHSOFPOUNDSTHE
WEIGHTOFTHEFOODMINUSTHECONTAINER
s5SE!54/$%&2/34ONLYFORRAWFOOD!54/
$%&2/34GIVESBESTRESULTSWHENFOODTOBETHAWEDIS
AMINIMUMOF &TAKENDIRECTLYFROMATRUEFREEZER)F
FOODHASBEENSTOREDINAREFRIGERATORFREEZERTHATDOES
NOTMAINTAINATEMPERATUREOF &ORBELOWALWAYS
PROGRAMALOWERFOODWEIGHTFORASHORTERDEFROSTING
TIMETOPREVENTCOOKINGTHEFOOD
s)FTHEFOODISSTOREDOUTSIDETHEFREEZERFORUPTO
MINUTESENTERALOWERFOODWEIGHT
s4HESHAPEOFTHEPACKAGEALTERSTHEDEFROSTINGTIME
3HALLOWRECTANGULARPACKETSDEFROSTMOREQUICKLYTHANA
DEEPBLOCK
s3EPARATEPIECESASTHEYBEGINTODEFROST3EPARATED
PIECESDEFROSTMOREEASILY
s3HIELDAREASOFFOODWITHSMALLPIECESOFFOILIFTHEYSTART
TOBECOMEWARM
s9OUCANUSESMALLPIECESOFALUMINUMFOILTOSHIELD
FOODSLIKECHICKENWINGSLEGTIPSANDFISHTAILSBUTTHE
FOILMUSTNOTTOUCHTHESIDEOFTHEOVEN&OILCAUSES
ARCINGWHICHCANDAMAGETHEOVENLINING
16027303
B – 11
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
3.!#+3
3.!#+3LETSYOUHEATCATEGORIESOFFOOD.ACHOS#HICKEN7INGS0OTATO3KINSAND#HEESE3TICKS
%XAMPLE4OCOOKCHICKENWINGS
4OUCH3.!#+3PAD
#ATEGORY
#HOOSEFOODCATEGORY
.ACHOS
4OUCH%.4%234!24PAD
4OUCH0AD.UMBER
#HICKEN7INGS
0OTATO3KINS
#HEESE3TICKS
3.!#+3#(!24
)TEM
.ACHOS
!MOUNTOR
SERVINGS
SERVING
2EMARKS
s0LACETORTILLACHIPSONPLATEWITHOUTOVERLAPPING
s3PRINKLEEVENLYWITHCHEESE
s#ONTENTS
CUPSTORTILLACHIPS
CUPGRATEDCHEESE
#HICKEN7INGS OZ
OZ
s5SEPRECOOKEDREFRIGERATEDCHICKENWINGS
s0LACECHICKENWINGSAROUNDPLATEINSPOKEFASHIONANDCOVERWITHWAXPAPER
0OTATO3KINS
COOKEDPOTATO
COOKEDPOTATOES
s#UTCOOKEDPOTATOINTOEVENWEDGES3COOPORCUTOUTPOTATOFLESHLEAVING
ABOUTvOFSKIN
s0LACESKINSINSPOKEFASHIONAROUNDPLATE
s3PRINKLEWITHBACONONIONSANDCHEESE$ONOTCOVER
#HEESE3TICKS
PCS
PCS
s0LACECHEESESTICKSONPLATEINSPOKEFASHION
s$ONOTCOVER
B – 12
16027303
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
3/&4%.-%,4
3/&4%.-%,4LETSYOUSOFTENORMELTCATEGORIESOFFOOD-ELT#HOCOLATE3OFTEN#REAM#HEESEAND-ELT"UTTER
%XAMPLE4OMELTCHOCOLATE
4OUCH3/&4%.-%,4PAD
#HOOSEFOODCATEGORY
4OUCH%.4%234!24PAD
#ATEGORY
4OUCH0AD.UMBER
-ELT#HOCOLATE
3OFTEN#REAM#HEESE
-ELT"UTTER
3/&4%.-%,4#(!24
)TEM
-ELT#HOCOLATE
!MOUNTOR
SERVINGS
SQUARESOR
CUPCHIPS
3OFTEN#REAM#HEESE PACKAGEOZ
-ELT"UTTER
STICKLB
STICKSLB
© 2006 Maytag Services
2EMARKS
s0LACECHOCOLATECHIPSORSQUAREINAMICROWAVESAFEDISH
s3TIRWELLATHALFTIMEWHENTHEOVENBEEPSANDRESTARTTHEOVEN
s5NLESSSTIRREDTHECHOCOLATEKEEPSITSSHAPEEVENWHENHEATINGTIMEISOVER
s5NWRAPCREAMCHEESEANDPLACEONMICROWAVESAFEDISH
s,ETSTANDMINUTES
s2EMOVEWRAPPINGANDCUTBUTTERINHALFVERTICALLY
s0LACEBUTTERINDISHCOVERWITHWAXPAPER
s3TIRWELLAFTERFINISHINGANDLETSTANDMINUTES
16027303
B – 13
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
-)#2/#/.6%#4
4HISOVENCANCOOKFOODWITHOUTENTERINGCOOKINGTIMEORPOWERLEVELUSING-)#2/#/.6%#4
-)#2/#/.6%#4HASFOODCATEGORIES7HOLE#HICKEN2OAST0ORK&ROZEN,ASAGNA"AKED0OTATOES
%XAMPLE4OCOOKLBSROASTPORK
4OUCH34/0#,%!2PAD
4OUCH-)#2/#/.6%#4PAD
#HOOSEFOODCATEGORY
4OUCHNUMBERPADSFORFOODQUANTITY
4OUCH%.4%234!24PAD
-)#2/#/.6%#44!",%
#!4%'/29
7HOLE#HICKEN
4/5#(
0!$
7%)'(4
2!#+3):%
#/--%.43
LBS
&OLDCHICKENWINGSUNDERTHECHICKEN"RUSH
,OWRACKONENAMEL WITHMELTEDBUTTER0LACECHICKENBREASTSIDE
METALTRAYONGLASS DOWNONLOWRACKONMETALTRAYONTURNTABLE
TURNTABLE
7HENOVENBEEPSTURNCHICKENOVERAND
RESTARTOVEN,ETSTANDMINUTES
2OAST0ORK
"ONELESS
4ENDERLOIN
LBS
0LACEPORKONLOWRACK0LACEWIRERACKON
,OWRACKONENAMEL
METALTRAYONTURNTABLE7HENOVENBEEPS
METALTRAYONGLASS
TURNROASTOVERANDRESTARTOVEN,ETSTAND
TURNTABLE
MINUTES
&ROZEN,ASAGNA
OZOR
OZ
,OWRACKONGLASS
TURNTABLE
POTATOES
0LACEPOTATOESONMEDIUMWIRERACK0LACE
-EDIUMWIRERACKON WIRERACKONGLASSTURNTABLE7HENOVEN
GLASSTURNTABLE
BEEPSTURNPOTATOESOVERANDRESTARTOVEN
,ETSTANDMINUTES
"AKED0OTATOES
0LACELASAGNAONLOWRACK0LACEWIRERACK
ONGLASSTURNTABLE,ETSTANDTOMINUTES
./4%
7HENCHECKINGFOODFORDONENESSDURINGCOOKINGCAREFULLYREMOVEFOODRACKANDDRIPTRAYIFUSEDFROMTHEOVEN
ANDCLOSEOVENDOORTOPREVENTEXCESSIVEHEATLOSS
B – 14
16027303
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
!54/"2/),#//+).'
(AMBURGER"EEF3TEAK#HICKEN0IECES&ISH3TEAK
!UTO"ROILLETSYOUCOOKWITHBROILHEATWITHOUTSETTINGACOOKINGTIME#HOOSETHECATEGORYOFTHEFOODYOUARECOOKING
ANDENTERTHEQUANTITY
3EETHE!54/"2/),#(!24ONTHISPAGEFORTHESETTINGSAVAILABLE
4OUCH34/0#,%!2PAD
./4%
s0LACEFOODONCERAMICENAMELDRIPPAN
s0LACEDRIPPANONHIGHRACK
s0LACERACKONTURNTABLE
4OUCH!54/"2/),PAD
#HOOSEFOODCATEGORY
4OUCHNUMBERPADFORFOODQUANTITY
4OUCH%.4%234!24PAD
#!4%'/29
4/5#(
0!$./
!-/5.4
#/--%.4
(AMBURGER
PATTIES
0LACEHAMBURGERSONCERAMICENAMELDRIPPANTHENPLACEPANONHIGH
RACKANDINOVEN7HENOVENBEEPSTURNTHEFOODOVERANDRESTART
THEOVEN
"EEF3TEAK
PCS
0LACEBEEFSTEAKONCERAMICENAMELDRIPPANTHENPLACEPANONHIGH
RACKANDINOVEN7HENOVENBEEPSTURNTHEFOODOVERANDRESTART
THEOVEN
#HICKEN
"REAST
LBS
0LACECHICKENBREASTONCERAMICENAMELDRIPPANTHENPLACEPANON
HIGHRACKANDINOVEN7HENOVENBEEPSTURNTHEFOODOVERANDRE
STARTTHEOVEN
&ISH3TEAK
PCS
0LACEFISHSTEAKONCERAMICENAMELDRIPPANTHENPLACEPANONHIGH
RACKANDINOVEN7HENOVENBEEPSTURNTHEFOODOVERANDRESTART
THEOVEN
./4%
7HENCHECKINGFOODFORDONENESSDURINGCOOKINGCAREFULLYREMOVEFOODRACKANDDRIPTRAYIFUSEDFROMTHEOVEN
ANDCLOSEOVENDOORTOPREVENTEXCESSIVEHEATLOSS
© 2006 Maytag Services
16027303
B – 15
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
#/.6%#4)/.#//+).'
$2)00!.
$URINGCONVECTIONCOOKINGAHEATINGELEMENTISUSED
TORAISETHETEMPERATUREOFTHEAIRINSIDETHEOVEN
#ONVECTIONCOOKINGTEMPERATURERANGESFROM &TO
&)TISBESTTOPREHEATTHEOVENWHENCONVECTION
COOKING
,OWEROVENTEMPERATUREBY &FROMPACKAGE
RECOMMENDEDTEMPERATUREINSTRUCTIONSIFLIGHTER
BROWNINGISPREFERRED4HEBAKINGTIMEMAYVARY
ACCORDINGTOTHEFOODCONDITIONORINDIVIDUAL
PREFERENCE#HECKDONENESSATTHEMINIMUMTIMEAND
THENADJUSTTIMEBYTOUCHINGTHE-OREOR,ESS
PAD
!CERAMICENAMELDRIPPANHASBEENINCLUDEDWITHYOUR
OVEN7HENROASTINGINTHEOVENPLACEFOODDIRECTLY
ONTHECERAMICENAMELPAN0LACETHERACKINSIDETHE
CERAMICENAMELDRIPPAN#ENTERTHEDRIPPANANDRACKON
THEGLASSTURNTABLE
7HENCOOKINGISCOMPLETEUSEPOTHOLDERSTOREMOVETHE
DRIPPANANDRACKFROMTHEHOTOVEN4AKECARENOTTO
SPILLTHEHOTDRIPPINGS2EMOVEFOODFROMTHERACK
&ORBESTRESULTSWHENBROILINGREMOVETHECERAMIC
ENAMELPANANDRACKFROMTHEOVENTOTURNFOOD2EPLACE
THETRAYANDRACKONTHETURNTABLETOCONTINUEBROILING
$ONOTUSEINMICROWAVEONLYMODE
#!54)/.
s4OAVOIDRISKOFBURNSHANDLEUTENSILSRACKSAND
DOORWITHCARE!LLOWOVENUTENSILSANDRACKSTOCOOL
BEFORECLEANING/VENUTENSILSANDRACKSBECOME
HOTDURINGOPERATION
s4OAVOIDRISKOFPERSONALINJURYORPROPERTYDAMAGE
DONOTUSEOVENWITHOUTTURNTABLEINPLACE
s4OAVOIDRISKOFPERSONALINJURYORPROPERTYDAMAGE
DONOTCOVERTURNTABLEORRACKWITHALUMINUMFOIL
s4OAVOIDRISKOFPROPERTYDAMAGEDONOTUSE
LIGHTWEIGHTPLASTICCONTAINERSPLASTICWRAPSORPAPER
PRODUCTSDURINGACONVECTIONCOOKINGCYCLE
s$O.OTTOUCHHOTSURFACES)NCLUDINGOVENCAVITY
OVENDOORTURNTABLERACKORPANUSEPOTHOLDER
"ROILING2ACK
(IGHRACK
$RIPPAN
4URNTABLE
"ROILING#ONVECTION
#OMBINATIONCOOKING
2ACK-EDIUMRACK
$RIPPAN
4URNTABLE
#/.6%#4)/.2!#+
5SETHECONVECTIONRACKSFORCONVECTIONANDCOMBINATION
COOKINGONLY
$ONOTUSERACKINMICROWAVEONLYMODE
&ORBESTRESULTSPLACEFOODONTHE#ONVECTION2ACK
-EDIUMRACK,OWRACK
#ONVECTION#OMBINATION
COOKING2ACK,OWRACK
$RIPPAN
4URNTABLE
,OWRACK
-EDIUMRACK
#/.6%#4)/.2!#+3
B – 16
16027303
© 2006 Maytag Services
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
#/.6%#4)/."!+).'7)4(
02%(%!4).'
#/.6%#4)/."!+).'7)4(/54
02%(%!4).'
%XAMPLE4OSET#ONVECTION"AKINGAT &0LACE
LOWORMEDIUMRACKONGLASSTURNTABLE5SEDRIPPAN
IFCOOKINGMEATSORPOULTRYONTHERACK
-EATS#ASSEROLESAND0OULTRY
4OUCH34/0#,%!2PAD
%XAMPLE4OSET#ONVECTION"AKINGAT &FOR
MINUTES0LACELOWORMEDIUMRACKONGLASS
TURNTABLE5SEDRIPPANIFCOOKINGMEATSORPOULTRYON
THERACK
4OUCH#/.6%#4)/.PAD
4OUCH34/0#,%!2PAD
4OUCHANUMBERPADTOSELECTBAKING
TEMPERATURE
4OUCH%.4%234!24PADTWICE
s!FTERPREHEATINGDISPLAYSCROLLS0,!#%&//$/.
2!#+WITHSOUND/PENTHEDOORPLACEFOODONTHE
CONVECTIONRACK
4OUCHNUMBERPADSFORCOOKINGTIME
9OUCANENTERATIMEUPTOMINUTES
SECONDS3EE#ONVECTIONCOOKING
'UIDEPAGE
#LOSETHEDOORAND4OUCH%.4%2
34!24PAD
./4%3
s4HEOVENTEMPERATUREDROPSVERYQUICKLYWHENTHE
DOORISOPENEDHOWEVERTHISSHOULDNOTPREVENTFOOD
FROMBEINGFULLYCOOKEDDURINGNORMALCOOKINGTIME
s7HENCHECKINGFOODFORDONENESSDURINGCOOKING
CAREFULLYREMOVEFOODRACKANDDRIPPADIFUSEDFROM
THEOVENANDCLOSEOVENDOORTOPREVENTEXCESSIVE
HEATLOSS
© 2006 Maytag Services
16027303
4OUCH#/.6%#4)/.PAD
4OUCHANUMBERPADTOSELECTBAKING
TEMPERATURE9OUCANENTERA
TEMPERATUREBETWEEN &AND &
4OUCH%.4%234!24PADONCE
4OUCHNUMBERPADSFORCOOKINGTIME
9OUCANENTERATIMEUPTOMINUTES
SECONDS
4OUCH%.4%234!24PAD
)-0/24!.4
s)FYOUSETANINCORRECTCOOKINGTIMEJUSTREENTERTHE
CORRECTCOOKINGTIMEANDTHENTOUCH%.4%234!24
PAD
s)FYOUTOUCH34/0#,%!2PADTHENENTERTHECORRECT
COOKINGTIMEYOUWILLCANCELTHE#/.6%#4)/.
OPERATIONANDWILLBECOOKINGWITHMICROWAVEENERGY
AND./4CONVECTION
B – 17
Use and Care
2SHUDWLQJ,QVWUXFWLRQV
"2/),#//+).'
"ROILINGISCOOKINGUNDERDIRECTHEAT4HISOVENCANBROILMEATFISHPOULTRYANDVEGETABLESORTOASTBREAD
9OUROVENUSESBROILCOOKINGWHENEVERYOUUSETHE"ROIL0AD
s&OODSTHATARESUITABLEFORBROILINGSHOULDBETENDERMODERATELYLEANANDNOMORETHANINCHTHICK&ISHSTEAKS
CHICKENBREASTSANDHAMBURGERSAREIDEALFORBROILING
s!LWAYSUSEEITHERTHETALLORMEDIUMRACKWHENBROILING0LACETHERACKONTHECERAMICENAMELDRIPPAN
s&OREVENBROWNINGTURNTHEFOODOVERHALFWAYTHROUGHBROILING
s$ONOTLEAVETHEDOOROPENFORLONGPERIODSOFTIMEWHENUSINGTHEBROILELEMENT4HISWILLCAUSETHEOVENTEMPERATURE
TODROPANDCOULDAFFECTCOOKINGPERFORMANCE
"2/),).'2!#+
"2/),#//+).'
5SETHEBROILINGRACKFORBROILANDAUTOBROILCOOKING
$ONOTUSERACKSINMICROWAVEONLYMODE
&ORBESTRESULTSPLACEFOODONTHEBROILINGRACK(IGH
RACK-EDIUMRACK
%XAMPLE4OSET"ROIL#OOKINGFORMINUTES
4OUCH34/0#,%!2PAD
4OUCH"2/),PAD
4OUCHNUMBERPADSFORCOOKING
TIME9OUCANENTERATIMEUPTO
MINUTESSECONDS
4OUCH%.4%234!24PAD
(IGHRACK
./4%3
s)FYOUOPENTHEDOORORTOUCH34/0#,%!2PAD
DURINGBROILINGBROILINGWILLSTOP
s4ORESUMEBROILINGCLOSETHEDOORANDTOUCH%.4%2
34!24PAD
s7HENBROILINGTIMEENDSTHEDISPLAYWILLSHOW%.$
ANDFOURTONESWILLSOUND
s!FTERCOOKINGTHEDISPLAYWILLRETURNTOTHETIMEOFDAY
WHENYOUOPENTHEDOOR
-EDIUMRACK
!54/"2/),4!",%
&//$
#//+4)-%
-INUTESPERSIDE
-EDIUM &
(AMBURGER¢
"EEF
3TEAK
0OULTRY
0ORK
2IBEYE¢TO
.EW9ORK3TRIP¢TO
4"ONE3TEAK
#HICKEN"REASTBONEIN
#HICKEN"REASTBONELESS
#HICKEN,EGS
#HICKEN4HIGHS
0ORK#HOPS"ONELESS¢
0ORK#HOPS"ONELIN¢
(AM3LICEšTO¢
&ILLET¢TO
&ISH
3TEAK¢TO
B – 18
#//+4)-%
-INUTESPERSIDE
7ELLDONE &
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
MINUTES
4OTAL4IME
MINUTES
4OTAL4IME
16027303
#/--%.43
2EMOVEPANANDTURNMEATOVERHALFWAY
THROUGHTCOOKING
2EMOVEPANANDTURNMEATOVERHALFWAY
THROUGHTCOOKING
2EMOVEPANANDTURNMEATOVERHALFWAY
THROUGHTCOOKING
s#OOKCHICKENBREASTTO &
s#OOKCHICKENLEGSTHIGHTO &
2EMOVEPANANDTURNMEATOVERHALFWAY
THROUGHTCOOKING
s(AM3TEAKREHEATTO &
$ONOTTURNFISH
#OOKFISHUNTILITFLAKES
© 2006 Maytag Services
Use and Care
&DUHDQG&OHDQLQJ
#!2%!.$#,%!.).'
&ORBESTPERFORMANCEANDSAFETY
KEEPTHEOVENCLEANINSIDEANDOUT
SIDE4AKESPECIALCARETOKEEPTHE
INNERDOORPANELANDTHEOVENFRONT
FRAMEFREEOFFOODORGREASEBUILDUP
.EVERUSEROUGHPOWDERORPADS
7IPETHEMICROWAVEOVENINSIDEAND
OUTINCLUDINGTHEHOODBOTTOMCOVER
WITHASOFTCLOTHANDAWARMNOTHOT
MILDDETERGENTSOLUTION4HENRINSE
ANDWIPEDRY5SEACHROMECLEANER
ANDPOLISHONCHROMEMETALAND
ALUMINUMSURFACES7IPESPATTERS
IMMEDIATELYWITHAWETPAPERTOWEL
ESPECIALLYAFTERCOOKINGCHICKENOR
BACON#LEANYOUROVENWEEKLYOR
MOREOFTENIFNEEDED
&OLLOWTHESEINSTRUCTIONSTOCLEAN
ANDCAREFORYOUROVEN
s+EEPTHEINSIDEOFTHEOVENCLEAN
&OODPARTICLESANDSPILLEDLIQUIDS
CANSTICKTOTHEOVENWALLSCAUSING
THEOVENTOWORKLESSEFFICIENTLY
s7IPEUPSPILLSIMMEDIATELY5SEA
DAMPCLOTHANDMILDSOAP$ONOT
USEHARSHDETERGENTSORABRASIVES
s4OHELPLOOSENBAKEDONFOOD
PARTICLESORLIQUIDSHEATTWOCUPSOF
WATERADDTHEJUICEOFONELEMONIF
YOUDESIRETOKEEPTHEOVENFRESH
INAFOURCUPMEASURINGGLASSAT
(IGHPOWERFORFIVEMINUTESORUNTIL
BOILING,ETSTANDINTHEOVENFORONE
ORTWOMINUTES
s2EMOVETHEGLASSTRAYFROMTHE
OVENWHENCLEANINGTHEOVEN
ORTRAY4OPREVENTTHETRAYFROM
BREAKINGHANDLEITCAREFULLYANDDO
NOTPUTITINWATERIMMEDIATELYAFTER
COOKING7ASHTHETRAYCAREFULLY
INWARMSUDSYWATERORINTHE
DISHWASHER
s#LEANTHEOUTSIDESURFACEOFTHE
OVENWITHSOAPANDADAMPCLOTH
$RYWITHASOFTCLOTH4OPREVENT
DAMAGETOTHEOPERATINGPARTSOF
THEOVENDONTLETWATERSEEPINTO
THEOPENINGS
s7ASHTHEDOORWINDOWWITHVERY
MILDSOAPANDWATER"ESURETOUSE
ASOFTCLOTHTOAVOIDSCRATCHING
© 2006 Maytag Services
s)FSTEAMACCUMULATESINSIDEOR
OUTSIDETHEOVENDOORWIPEWITHA
SOFTCLOTH3TEAMCANACCUMULATE
WHENOPERATINGTHEOVENINHIGH
HUMIDITYANDINNOWAYINDICATES
MICROWAVELEAKAGE
s.EVEROPERATETHEOVENWITHOUT
FOODINITTHISCANDAMAGETHE
MAGNETRONTUBEORGLASSTRAY9OU
MAYWISHTOLEAVEACUPOFWATER
INTHEOVENWHENITISNOTINUSE
TOPREVENTDAMAGEIFTHEOVENIS
ACCIDENTALLYTURNEDON
4OREINSTALLTHEFILTERSLIDEITINTOTHE
SIDESLOTTHENPUSHUPANDTOWARD
OVENCENTERTOLOCK
#/.6%#4)/."2/),).'
2!#+3$2)00!.
7ASHTHECONVECTIONANDBROILING
RACKSANDMETALTRAYDRIPPANWITHA
MILDSOAPANDASOFTORNYLONSCRUB
BRUSH$RYCOMPLETELY$ONOTUSE
BRASIVESCRUBBERSORCLEANERSTO
CLEANRACKSANDMETALTRAYDRIPPAN
#,%!.).'4(%'2%!3%
&),4%2
4HEGREASEFILTERSHOULDBEREMOVED
ANDCLEANEDOFTENATLEASTONCEA
MONTH
#!54)/.
4OAVOIDRISKOFPERSONALINJURYOR
PROPERTYDAMAGEDONOTOPERATE
OVENHOODWITHOUTFILTERSINPLACE
4OREMOVEGREASEFILTERSLIDEFILTER
TOTHESIDE0ULLFILTERDOWNWARDAND
PUSHTOTHEOTHERSIDE4HEFILTERWILL
DROPOUT
#(!2#/!,&),4%2
2%0,!#%-%.4
)FYOUROVENISVENTEDTOTHEINSIDE
THECHARCOALFILTERSHOULDBEREPLACED
EVERYTOMONTHSANDMORE
OFTENIFNECESSARY4HECHARCOAL
FILTERCANNOTBECLEANED4OORDER
ANEWCHARCOALFILTERCONTACTTHE
0ARTS$EPARTMENTATYOURNEAREST
!UTHORIZED3ERVICE#ENTERORCALL
INSIDE53!AND#ANADA
5NPLUGOVENORTURNOFFPOWERAT
THEMAINPOWERSUPPLY
/PENTHEDOOR
2EMOVETHETWOVENTGRILLE
MOUNTINGSCREWSMIDDLE
SCREWS
3LIDETHEGRILLETOTHELEFTTHENPULL
STRAIGHTOUT
2EMOVEOLDFILTER
3OAKGREASEFILTERINHOTWATERAND
AMILDDETERGENT2INSEWELLAND
SHAKETODRY$ONOTUSEAMMONIA
ORPLACEINADISHWASHER4HE
ALUMINUMWILLDARKEN
16027303
B – 19
Use and Care
&DUHDQG&OHDQLQJ
3LIDEANEWCHARCOALFILTERINTO
PLACE4HEFILTERSHOULDRESTATTHE
ANGLESHOWN
/6%.,)'(4
2%0,!#%-%.4
5NPLUGOVENORTURNOFFPOWERAT
THEMAINPOWERSUPPLY
/PENTHEDOOR
2EMOVETHEVENTCOVERMOUNTING
SCREWSMIDDLESCREWS
3LIDETHEGRILLETOTHELEFTTHENPULL
STRAIGHTOUT
2EPLACETHEMOUNTINGSCREWSAND
CLOSETHEDOOR4URNTHEPOWER
BACKONATTHEMAINPOWERSUPPLY
ANDSETTHECLOCK
#(!2#/!,&),4%20!24./
0
#//+4/0.)'(4,)'(4
2%0,!#%-%.4
/04)/.!,
&ILLER+ITS
58!"$"",!#+
58!"$77()4%
58!"$334!).,%33
34%%,
7HENREPLACINGARANGEHOOD
THEFILLERKITFILLSINTHEADDITIONAL
WIDTHTOPROVIDEACUSTOMBUILTIN
APPEARANCE
&ORINSTALLATIONBETWEENCABINETS
ONLYNOTFORENDOFCABINET
INSTALLATION
%ACHKITCONTAINSTWOWIDEFILLER
PANELS
2EMOVETHESCREWLOCATEDABOVE
THEDOORNEARTHECENTEROFTHE
OVENTHATSECURESTHEBULBHOLDER
#!54)/.
4OAVOIDPERSONALINJURYORPROPERTY
DAMAGEWEARGLOVESWHEN
REPLACINGLIGHTBULB
5NPLUGTHEOVENORTURNOFFPOWER
ATTHEMAINPOWERSUPPLY
2EMOVETHEBULBCOVERMOUNTING
SCREWS
2EPLACEBULBWITHWATT
APPLIANCEBULB
2EPLACEBULBCOVERANDMOUNTING
SCREWS
4URNTHEPOWERBACKONATTHEMAIN
POWERSUPPLY
B – 20
2EMOVEBULBHOLDER
2EPLACEBULBWITHAWATT
APPLIANCEBULB
2EPLACETHEBULBHOLDER
2EPLACETHEGRILLEANDSCREWS
4URNTHEPOWERBACKONATTHEMAIN
POWERSUPPLY
16027303
© 2006 Maytag Services
Download PDF

advertising