Owner`s manual | Equator MJ-9000VG Washer/Dryer User Manual

Commercial Back Pack Vacuum
OWNER’S MANUAL
Model BPV325H
120V., 60Hz., 12 Amps
FOR HOUSEHOLD OR COMMERCIAL USE
USA: EURO-PRO OPERATING LLC
Canada:
94 Main Mill Street, Door 16
Plattsburg, NY 12901
Tel.: 1 (800) 798-7398
COPYRIGHT© EURO-PRO OPERATING LLC 2006
EURO-PROOPERATING LLC
4400 Bois Franc
St. Laurent, QC H4S 1A7
IMPORTANT SAFETY INSTRUCTIONS
Model
BPV325H
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase when used for
normal commercial or household use, subject to the following conditions, exclusions and
exceptions.
Should your appliance fail to operate properly while in use under normal commercial or
household conditions within the warranty period, return the complete appliance and accessories,
freight prepaid to:
U.S.:
EURO-PRO Operating LLC, 94 Main Mill Street, Plattsburgh, N.Y., 12901
Canada:
EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec, H4S 1A7
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date must be included. *
Non-durable parts including, without limitation, filters, rotating brushes, dust bags and electrical
parts which normally require replacement are specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with. This limited warranty does not cover
damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or
mishandling in transit. This warranty does not cover damage or defects caused by or resulting
from damages from shipping or repairs, service or alterations to the product or any of its parts,
which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event
is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential
damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
When using your Vacuum, basic safety precautions should always be observed,
including the following:
Read all instructions before using this vacuum.
WARNING: To reduce the risk of fire,
electrical shock, or injury:
1. Do not leave vacuum cleaner unattended when it is plugged in. Unplug
from outlet when not in use and before
removing filters.
2. To reduce the risk of electric shock – do
not use outdoors or on wet surfaces.
3. Do not allow children to use as a toy.
Close attention is necessary when used
by or near children.
4. Use only as described in this manual. Use
only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug.
Do not use vacuum cleaner if it has been
dropped, damaged, left outdoors, or
dropped into water. Return appliance to
EURO-PRO Operating LLC for
examination, repair or adjustment.
6. Do not pull or carry by cord. Do not use
cord as a handle, close a door on cord,
or pull cord around sharp edges or
corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
8. Do not handle plug or vacuum cleaner
with wet hands.
9. Do not use the vacuum cleaner to pick
up large objects or objects that are likely
to damage the vacuum cleaner.
10. Keep hair, loose clothing, fingers, feet and
all parts of body away from openings,
rotating agitator and other moving parts.
Do not operate cleaner in bare feet or
when wearing open toe shoes.
11. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking, or burning
objects.
12. Do not pick up hard or sharp objects
such as glass, nails, screws, coins, etc.
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The
registration will enable us to contact you in the unlikely event of a product safety notification. By
returning this card you acknowledge to have read and understood the instructions for use, and
warnings set forth in the accompanying instructions. Return to:
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
Model BPV325H
_____________________________________________________________________
Appliance model
_____________________________________________________________________
Date purchased
Name of store
_____________________________________________________________________
Owner's name
_____________________________________________________________________
Address
Printed in China
City
State
12
Zip Code
13. Do not use without all filters in place.
Use ONLY filters and accessories
provided by EURO-PRO Operating LLC.
Failure to do so will void the warranty.
14. Turn off all controls before plugging or
unplugging vacuum cleaner into electrical
outlet.
15. Use extra care when vacuuming on stairs.
16. Do not pick up flammable or
combustible materials (lighter fluid,
gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
17. Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
18. Do not use in an enclosed space filled
with vapors given off by oil based paints,
paint thinner, moth proofing substances,
flammable dust, or other explosive or
toxic vapors.
19. Use only on dry, indoor surfaces.
20. Do not use for any purpose other than
described in this user’s guide.
21. The use of an extension cord is not
recommended.
22. Do not put any objects into openings.
Do not use with any opening blocked.
Keep free of dust, lint, hair and anything
else that may reduce air flow.
23. Always store your appliance indoors in
a cool, dry area.
24. Keep your work area well lit.
25. Do not immerse the vacuum into water
or other liquids.
26. Keep end of hose, wands and other
openings away from your face and body.
27. To avoid damaging the carpet, keep the
vacuum cleaner head moving at all times.
28. Connect to a properly grounded outlet
only. See grounding instructions.
Warning: The power cord on this product
contains lead, a chemical known to the State
of California to cause birth defects or other
reproductive harm. Wash hands after
handling.
SAVE THESE INSTRUCTIONS
For Household or Commercial Use Only
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug
must be inserted into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING: Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or service person if you
are in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the appliance - if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding
attachment plug that looks like the plug illustrated at right. Make sure that
the appliance is connected to an outlet having the same configuration as
the plug. No adaptor should be used with this appliance.
1
Rev. 06/06A
PRECAUTIONARY MEASURES
TROUBLESHOOTING GUIDE
Important: If the suction opening of the unit, the hose or the extension tubes are
BLOCKED, switch off the vacuum cleaner and remove the blocking
substance before you start the unit again.
1.
2.
3.
Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
Before you start vacuuming,
make sure to remove large or
sharp objects that might
damage the dust bag.
When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
4.
5.
6.
7.
Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.
Do not use without all filters and
dust bag in place.
Do not vacuum any liquids.
Keep hair, loose clothing, fingers,
feet and all parts of body away
from openings, rotating agitator
and other moving parts.
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
Motor runs but no
suction
1. Hose extension tube or
air inlet is blocked.
2. HEPA dust bag is full.
3. Hose not assembled to
hose inlet properly.
1. Check for blockage (remove
blockage).
2. Replace HEPA dust bag.
3. Insert hose into hose inlet
and turn counter-clockwise
until it locks into place.
Turbo brush does
not rotate or
rotates slowly
1. Rotating brush or elbow
obstructed.
2. Belt is broken.
3. Hose is obstructed.
4. HEPA pre-motor filter is
blocked.
1.
2.
3.
4.
Clear obstructions.
Call 1 (800) 798-7398.
Clear obstruction.
Clean HEPA pre-motor filter.
Vacuum won’t run
1. Not firmly plugged in.
2. No electricity in wall
outlet.
3. Blown fuse/tripped
breaker.
4. Motor thermostat may
have tripped.
1.
2.
3.
4.
Plug unit in firmly.
Check fuse or breaker.
Replace fuse/reset breaker.
Turn vacuum off and unplug
from outlet. Allow unit to cool
down before trying to switch
on again.
ORDERING REPLACEMENT PARTS
TO ORDER REPLACEMENT BAGS
Item #XHB325H
For Model BPV325H
Call: 1 (800) 798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M.
Eastern Standard Time
Please Note:
The HEPA pre-motor and exhaust filters may be washed. We recommend that this be
done once a month or when suction appears reduced .To wash your HEPA pre-motor
filter and exhaust filter, hold and rinse under lukewarm water. When finished, shake off
excess water. DO NOT wash in dishwasher. It is important that when you wash any
filter, you allow it to air dry COMPLETELY before using again. We recommend 24
hours to air dry. DO NOT DRY IN DRYER.
IMPORTANT:
Both the HEPA pre-motor filter and the exhaust filter should be re-placed every three
(3) to six (6) months depending on usage. All filters, the shake-out bag and HEPA
dust bag should be checked regularly for signs of damage, preferable after each
cleaning task. The HEPA dust bag, shake-out bag and filters must be replaced
immediately if they become damaged. Always disconnect the vacuum from the
electrical outlet when checking the filters. NEVER re-use the HEPA dust bags.
Always replace the dust bags with new ones.
2
11
OPERATING INSTRUCTIONS
GETTING TO KNOW YOUR BACK PACK VACUUM
Warning: To reduce the risk of electric shock, the power cord must be
disconnected before removing the dust bag, shake-out bag,
changing the filters or performing maintenance or troubleshooting checks.
The HEPA pre-motor filter should be
replaced every three (3) to six (6)
months to ensure peak performance of
your vacuum.
Changing & Cleaning the
Exhaust Filter
Note: The exhaust filter is located in
the front of the vacuum.
Important Note: This filter is a
washable filter and can be cleaned by
rinsing under lukewarm water.
Always allow the exhaust filter to air dry
for 24 hours before replacing in the
vacuum. Do not use a hair dryer to dry
it. Air dry only. To remove the exhaust
filter:
1. While pushing up the exhaust tab,
pull out the exhaust grill. (Fig. 25)
Exhaust
Tab
Motor Thermostat
Important: This unit is equipped with
a motor protective thermostat. If for
some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Turn the unit off.
• Disconnect the plug from the power
source.
• Check the source of overheating
problem. (i.e. clogged hose, full dust
bag or filter).
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for 45
minutes, plug in the cleaner and
turn the unit on. The vacuum
should start again.
• If the vacuum still does not start,
contact customer service at:
1 (800) 798-7398.
Exhaust
Grill
Fig. 25
2. Remove the exhaust filter.
3. Clean the exhaust filter by rinsing
under lukewarm water.
4. After air drying for 24 hours, replace
into the vacuum.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Main Unit
Exhaust Grill
On/Off Power Switch
Canister Lid Tabs
Waist Band
Shoulder Straps
Back Board Panel
Carry Handle
Hose Inlet
Canister Lid
Flexible Hose
Flexible Hose Handle
Variable Suction Control
Telescopic Tube Release Button
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Telescopic Tube
Waist Band Back Support Panel
Waist Band Tool Carrier
Dusting Brush
Crevice Tool
Blower Port
Pet Hair Remover
Floor to Carpet Brush
Air Driven Turbo Brush
Blower Attachments (x3)
HEPA Dust Bag
Shake-Out Bag
HEPA Pre-Motor Filter
Exhaust Filter
Technical Specifications
Voltage:
Power:
120V., 60Hz.
12 Amps
* Note: Illustrations may differ from actual product.
10
3
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Warning: To reduce the risk of electric shock, the power cord must be
disconnected before removing the dust bag, shake-out bag,
changing the filters or performing maintenance or troubleshooting checks.
5. The cardboard face of the new bag
should rest securely in the dust bag
cover guides. (Fig. 3)
Assembling Your Vacuum
Cleaner
Note: Always remove the power plug
from the wall outlet before assembling
or removing accessories.
disconnected before removing the dust bag, shake-out bag, changing
the filters or performing maintenance or trouble-shooting checks.
4. Replace the HEPA dust bag with a new
bag. Do not reuse the same bag.
5. The cardboard face of the new bag
should rest securely in the dust bag
cover guides. (Fig. 24)
2. The shake-out bag is hand washable
in lukewarm water.
3. Allow to air dry for 24 hours. The
shake-out bag should be replaced
when needed. Never replace into
the vacuum if still wet.
Note: If used often without HEPA dust
bag, replacement and washing will be
required more often.
4. Replace clean shake-out bag in unit,
and replace the canister lid onto the
vacuum.
Tab
Inserting the HEPA Dust Bag
Note: This unit can be used with the
shake-out bag alone, however it must
be cleaned after every use if there is
no HEPA dust bag installed.
Fig. 24
Fig. 3
6. Ensure that the shake-out bag is in
place. (Fig. 4)
Important: DO NOT use the vacuum
without all filters, shake-out bag, and
with or without HEPA dust bag in place.
1. Unplug the hose connecting power
cord and remove the flexible hose.
2. To open the canister lid press on
the canister lid tabs on each side
of the unit and lift canister lid.
(Fig. 1)
Shake-Out
Bag
Canister Lip
Fig. 4
Canister
Lid
Tabs
Warning: To reduce the risk of electric shock, the power cord must be
7. Flip the HEPA bag holder over,
pressing the tab on the bag holder
until it clicks, then replace the
canister lid.
8. The canister lid can be replaced on
the unit with the hose opening on
the right or left, as per your
preference. (Fig. 5)
Canister
Lid
Tabs
Fig. 1
3. Pull the tab on the HEPA dust bag
holder out slightly and flip upwards.
(Fig 2)
4. Holding the HEPA dust bag in your
hand, slide it firmly between the
slots in the bag holder. (Fig 2)
Right-Handed
Placement
Left-Handed
Placement
Fig. 5
Tab
Fig. 2
4
6. Replace the shake-out bag into the
vacuum.
7. To replace the HEPA dust bag holder,
flip the holder and press tab until it
clicks.
8. Replace the canister lid onto the
vacuum.
Warning: Never over fill the HEPA dust
bag – replace when bag is full and clean the
shake-out bag and filter each time the
HEPA dust bag is replaced.
Cleaning the HEPA Pre-Motor Filter
Important, Please Note: The HEPA
pre-motor filter will stop most of the tiniest
dust particles and airborne allergens from
re-entering the air you breathe. In fact it
stops 99.97% of all particles as small as
0.3 microns - many times smaller than a
human hair!
Because of this incredible filtration
performance, the HEPA pre-motor filter
will accumulate many fine dust particles
that are difficult to see. Be assured that
the HEPA pre-motor filter is doing the job.
Clean the HEPA pre-motor filter after
each use as described in this section.
1. Remove the shake-out bag from the
canister. The HEPA pre-motor filter
is located underneath the shake-out
bag. To remove the HEPA pre-motor
filter, lift the filter from the sides of the
HEPA filter.
2. Vigorously “TapClean” the HEPA
pre-motor filter on a hard surface to
remove any residual dust that might
still be on the HEPA pre-motor filter.
3. You can wash the HEPA pre-motor
filter by running it under the tap and
allowing the water to run on the dirty
side at least once a month or when
suction appears to be decreased.
Cleaning & Replacing the ShakeOut Bag
Note: Clean the shake-out bag out-doors
when changing the HEPA dust bag.
Optimum performance is achieved by
using the HEPA dust bag with the shakeout bag decreasing the need for washing
the shake-out bag.
Cleaning the Shake-Out Bag when Used
with the HEPA Dust Bag:
1. Remove the shake-out bag, holding the
handle at the bottom of the bag, shake
outdoors vigorously over a garbage
receptacle until there is no more dust.
2. Inspect shake-out bag regularly for
tears or damage. Replace shake-out
bags if damage or tears are present.
Cleaning the Shake-Out Bag when Used
Alone:
It is recommended that the shake-out bag
be washed after it has been used several
times without the HEPA dust bag in place.
1. Remove the shake-out bag, empty
contents into a trash can, and shake
vigorously outdoors until there is no
more dust.
Wash once a month
or when suction
appears reduced
Warning: Allow 24 hours
for drying before replacing
in unit.
9
OPERATING INSTRUCTIONS
5. To blow up inflatable items, select the
appropriate size blower attachment that
will fit into the air valve. (Fig. 19)
OPERATING INSTRUCTIONS
4. Turn the unit on by pressing the
switch located near the base of the
unit to turn the vacuum cleaner on.
(Fig. 21)
Power
Switch
Fig. 19
The flexible hose should be connected
to the vacuum before strapping the unit
to your back.
1. To connect the flexible hose into the
hose inlet, insert the threaded end
of the flexible hose into the hose
inlet and turn counter-clockwise
until it locks into place. (Fig. 6)
Telescopic Tube
Release
Fig. 9
Note: Always remove the power plug
from the wall outlet before assembling
or removing accessories.
Fig. 21
6. Turn the unit on and hold the blower
attachment and air valve while the
vacuum exhaust is pumping air into
the inflatable.
7. To detach the flexible hose turn
clockwise and pull out from blower
port.
Note: Firmly hold the flexible hose by the
attachment when blowing dirt or dust off of
objects.
Manual Suction Control
Removing & Replacing HEPA
Dust Bag
Your vacuum cleaner includes a
manual variable suction control on the
flexible hose handle . The suction
power can be adjusted by moving the
suction regulator to the desired position
between Open and Closed. (Fig. 10)
Open gives you less suction, closed
maximum suction. For example, less
suction is required on upholstery and
draperies compared to thick carpets,
which require maximum suction.
To remove the HEPA dust bag from the
vacuum:
Important: DO NOT use the vacuum
without all filters, shake-out bag, and
with or without HEPA dust bag in place.
1. To remove the HEPA dust bag,
press on the canister lid tabs on
each side of the unit and lift canister
lid. (Fig. 22)
Using Your Vacuum
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
bag, shake-out bag, changing the
filters or performing maintenance or
trouble-shooting checks.
1. Insert the power plug into the wall
outlet.
2. Connect hose and telescopic tube if
desired.
3. Correctly place shoulder straps on
each shoulder and secure the waist
band with hook and loop strips.
(Fig. 20)
Caution: If the waist band and both
shoulder straps are not properly and
securely in place the unit could fall off
your back causing damage or injury.
Shoulder
Strap
3. To remove the telescopic tube from
the flexible hose, press on the
telescopic tube release button and
pull it out. (Fig. 9)
Attaching the Flexible Hose to
the Vacuum
Canister
Lid Tabs
Canister
Lid Tabs
Fig. 6
2. Plug the power cord into the
electrical outlet.
3. To remove the flexible hose, unplug
the power cord and then turn the
hose clockwise and pull the flexible
hose out.
Attaching the Telescopic Tube to
the Flexible Hose Handle
1. Holding the telescopic tube, insert
the handle into the telescopic tube
receptacle. Push the handle in.
(Fig. 7)
Fig. 10
Using the Floor to Carpet Brush
1. To attach the floor to carpet brush to
the telescopic tube, insert the
telescopic tube into carpet to floor
brush. (Fig. 11)
Fig. 22
2. Pull the tab on the HEPA dust bag
holder out slightly and flip upwards.
(Fig. 22)
3. Holding the HEPA dust bag in your
hand, slide it out from the slots in
the bag holder. Hold carefully in
order to avoid having dust fall out
of HEPA dust bag. (Fig 23)
Shoulder
Strap
Fig. 7
2. Push forward on the plastic button
and pull the inner tube outward to
extend for a longer reach. (Fig. 8)
Floor to
Carpet
Brush
Tab
Waist
Band
&
Tool
Storage
Fig. 20
Dust
Bag
Holder
8
Fig. 8
Plastic
Button
Fig. 11
Fig. 23
5
OPERATING INSTRUCTIONS
2. Step on the floor to carpet selector
to adjust the height of the brushes.
There are two (2) different heights
one for floors and one for carpets.
(Fig. 12)
Using the Air Driven Turbo Brush
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the
HEPA dust bag, the shake-out bag,
HEPA pre-motor filter, changing the
filters or performing maintenance or
troubleshooting checks. The efficiency
of your air driven turbo brush depends
on the bristle brush rotating at high
speed. Strong air suction is needed to
accomplish this. In order to ensure that
maximum air suction is maintained,
please read the following instructions:
1. Change the HEPA dust bag or empty
the shake-out bag frequently.
2. Replace the pre-motor and exhaust
filters as needed.
3. Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.
4. To attach the air driven turbo brush,
insert the telescopic tube into the air
driven turbo brush.
Floor to
Carpet
selector
Fig. 12
3. To remove the telescopic tube from
the floor to carpet brush, pull the
telescopic tube out from the floor
to carpet brush.
Using the Attachments
Dusting Brush
The dusting brush is used
for the furniture
Crevice Tool
Use for radiators, crevices,
corners, baseboards and
between cushions.
Pet Hair Remover Brush
The pet hair remover brush
is used for upholstery. The
unique surface makes it an
excellent tool for removing
unwanted pet hair.
How To Clean the Air Driven
Turbo Brush
From time to time, the turbine of your
air driven turbo brush will require
cleaning. To do this:
1. Remove the turbo brush from the
telescopic tube.
2. Flip the turbo brush over so that the
bottom of it is facing upwards.
(Fig. 13)
Note: This tool is not a grooming tool
and should not be used on animals.
Caution: Do not use pet hair
remover brush on delicate or woven
fabrics that may snag.
DO NOT use pet hair remover brush on
wooden floors as this accessory might
cause mild scratching.
OPERATING INSTRUCTIONS
3. Using your thumb and index finger,
simultaneously squeeze the locking
tabs on either side of the trap door
and lift off. (Fig. 14) Doing so will
remove the trap door and allow you
access to the turbine for cleaning
and maintenance purposes. (Fig. 15)
Locking
Tabs
The blower attachments can be used
with the vacuum to pick up very fine dirt
particles in tight crevices or spots, or to
inflate inflatable items or air
mattresses.
Fig. 13
6
Exhaust
Tab
Fig. 14
Exhaust
Grill
Trap Door
Fig. 16
Turbine
Fig. 15
4. There may be some dust, lint, hair,
etc on the turbine wheel. Remove as
much of this as possible.
5. You may also use the unit’s hose with
the crevice tool attached and use the
vacuum to remove any additional
debris from the turbine.
6. Ensure that the turbine wheel moves
freely by rotating it with your finger. If
the turbine does not rotate, call EUROPRO Customer Service for help at
1 (800) 798-7398.
7. Once clean, replace the trap door of
the turbo brush. Ensure that it clicks
into place.
Using the Blower Attachments
Blower Attachments
The blower attachments have air bleed
holes. These air bleed holes help relieve
some air pressure so that the attachment
does not blow off. However, should an
increase in air pressure be desired,
simply cover one or more of the air bleed
holes.
To use the blower attachments:
1. Pull up and hold the exhaust tab, with
the free hand pull out the exhaust
grill. (Fig. 16)
The blower attachments are extremely
useful for vacuuming in hard to reach
crevices and small compartments such as in
cars.
Important Note: When blocking the air
bleed holes, grasp the blower attachments
firmly so that they do not blow off.
Note: Do not use blower function to clear
dust off of fragile or delicate objects unless
they are secured or held firmly in place as
the blower action is quite strong and could
cause damage.
7
2. Remove the exhaust filter.
3. To place the blower port into the
exhaust outlet, align the lower tabs
on the blower port with the slots on
the exhaust. Pull up on the exhaust
tab and push the top of the blower
port until it snaps into place. (Fig. 17)
Exhaust Tab
Blower
Port
Fig. 17
4. To attach the hose to the blower
port, align the flexible hose and turn
counter-clockwise until it stops. The
hose is now securely in place.
(Fig. 18)
Fig. 18
Download PDF

advertising