Ericsson 3213 Telephone User Manual

810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 1
Battery Operated
Carbon Monoxide
Alarm
User’s Guide
Battery operated CO alarm
without Digital display
Battery operated CO alarm
With Digital Display and
Peak Level memory
MODEL: KN-COB-BCA
ASSEMBLY: 9CO5
MODEL: KN-COPP-BCA
ASSEMBLY: 900-0146
For questions concerning your Carbon Monoxide Alarm,
please call our Consumer Hotline at 1-800-880-6788.
Please have the following information ready when calling:
CO Alarm Model Number (Located on the back of alarm):
CO Alarm Assembly Number (Located on back of alarm):
Date of Manufacture (Located on back of alarm):
Date of Purchase:
Where Purchased:
ATTENTION Please take a few minutes to thoroughly read this manual which
should be saved for future reference and passed on to any subsequent owner.
810-2263
Rev A
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 2
Table of Contents
Carbon Monoxide Overview
Carbon Monoxide Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Your new Kidde Carbon Monoxide (CO) Alarm is a sophisticated
i n s t rument that has been carefully designed and tested to detect CO
build up in a residential environments.
Kidde Product View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Quick Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Mounting
Where to Install
Where NOT to Install
Features and Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-15
Digital Display
Other Possible Displays
Peak Level Button
Test Reset Button/Lights
Battery Installation/Replacement . . . . . . . . . . . . . . . . . . . . 16-17
What To Do If The Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . 18-20
Symptoms of Carbon Monoxide Poisoning
Caring For Your Kidde
Battery Powered CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Wall Mounting Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-28
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Thank you for the purchase of your new Kidde carbon monoxide alarm.
If you have any questions about the operation or setup of your CO
alarm, feel free to call our Consumer Hotline at 1-800-880-6788.
2
CO cannot be seen, smelled or tasted and can be fatal. The build up
of CO in the blood is called the carboxyhemoglobin level and interf e res with the body’s ability to supply itself with oxygen. Depending
on the concentration, carbon monoxide can kill in minutes.
The most common sources of CO are malfunctioning, or misuse of,
gas appliances used for heating and cooking, vehicles engines, electric generators, blocked chimneys or flues, portable fuel burning
heaters, fireplaces, fuel powered tools and operating a grill in an
enclosed space.
Indications of CO poisoning include symptoms similar to the flu, but
with no fever. Other symptoms include dizziness, fatigue, weakness,
headache, nausea, vomiting, sleepiness and confusion. Everyone is
susceptible to the danger of CO, but unborn babies, small children,
pregnant women, senior citizens and people with heart or re s p i r a t o ry
problems may experience symptoms sooner. Each year a qualified
technician should inspect and clean your heating system, vents,
chimney, and flues.
Your new Kidde CO alarm has a five year limited warranty. Please
take a few minutes to thoroughly read the user’s guide and familiarize
yourself and your family with its operation. Your Kidde CO alarm was
designed to detect carbon monoxide gas from ANY source of combustion. It is NOT designed to detect smoke, fire or any other gases.
If you have any questions please call our Consumer Hotline at 1-800880-6788.
This manual and the products described are copyrighted, with all
rights re s e rved. Under these copyright laws, no part of this manual
may be copied for use without the written consent of Kidde.
If you require further information, contact our Consumer Hotline, or
write to us at:
Kidde / Pyrene Corp.
130 Esna Park Drive, Markham, ON, L3R 1E3
Consumer Hotline: 1-800-880-6788
www.kidde.ca
3
810-2263_RevA_146_MAN_ENG
4/14/04
Kidde Product Vi e w
900-0146 Digital display model
4
3:29 PM
Page 4
Kidde Product Vi e w
non-digital 9CO5 model
5
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 6
Quick Set Up
Installation Instructions
Remove the three enclosed AA batteries and install them into
the battery well. Carefully place the red b a t t e ry warning flags into
the battery well. Observe the battery polarity markings at the
bottom of the battery well. After approximately 30 seconds, your
CO alarm will begin monitoring for CO.
When choosing your installation locations, make sure you can hear the
alarm from all sleeping areas. If you install only one carbon monoxide
alarm in your home, install the alarm near bedrooms, not in the basement
or furnace room.
Installation Location
Recommended Locations
Upper Levels of Home
DINING
KITCHEN BEDROOM BEDROOM
LIVING ROOM
BEDROOM
Your Kidde CO Alarm is now operational.
Note:
Seven (7) years after initial power up, this unit will "chirp" every
30 seconds to indictate that it is time to replace the alarm. After
seven years the device may no longer detect carbon monoxide
accurately and should be replaced immediately. To help identify
the date to replace the unit, a label has been afficed to the side
of the alarm. Write teh "Replace by" date (7 years form power
up) in permanent marker on the label.
Basement Levels of Home
FURNACE
ROOM
• If you have only one alarm, place it near sleeping areas.
• Position near fuel burning appliances, near fireplaces, furnace
or hot water heater.
6
7
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 8
Installation Instru c t i o n s
Installation Instru c t i o n s (continued)
Mounting
Where NOT To Install Your Kidde CO Alarm
1. Using the template provided (see
page 25). Mark the location on wall.
2. I n s e rt the two screws provided until
the screw heads are approximately
1/8” from wall. (If mounting in
plaster board or drywall, drill 3/16”
hole and use the plastic anchors
provided.)
Figure 1
3. Hook the Kidde CO Alarm unit over the screws onto keyholes in back
of unit.
The digital model may also be placed on a tabletop. Simply fold out the
stand located on the back of the unit and place in a location that is easily
visible.
•
Do not install in dead air spaces such as peaks of vaulted
ceilings, or gabled roofs.
•
Do not install in turbulent air from ceiling fans. Do not place
near fresh air vents or close to doors and windows that open
to the outside.
•
Keep the CO alarm away from excessively dusty, dirty, or
greasy areas such as kitchens, garages and furnace rooms.
Dust, grease and household chemicals can affect the sensor.
•
Keep out of damp and humid areas such as the bathroom.
Avoid spraying aerosols near the CO alarm.
•
Do not install in areas where the temperature is below 40
degrees Fahrenheit (4.4° Celsius) or hotter than 100 degrees
Fahrenheit (37.8° Celsius) during use. This unit can be store d
to -10 degrees Fahrenheit without harm to the alarm but it
must be above 40 degrees Fahrenheit for use.
W h e re To Install Your Kidde CO Alarm
•
The following suggestions are intended to help you with the
placement and installation of your Kidde CO Alarm.
Do not place behind curtains or furniture. CO must be able
to reach the sensor for the unit to accurately detect CO.
•
DO NOT locate Alarm within 5 feet (1.5 meters) of any
cooking appliance.
•
Be aware that certain conditions can result in transient CO
situations, such as: i) Excessive spillage or reverse venting of
fuel-burning appliances caused by: 1) outdoor ambient conditions, such as wind direction and/or velocity, including high
gusts or wind and insufficient draft in vent pipes; 2) negative
pressure diff e rential resulting from the use of exhaust fans; 3)
simultaneous operation of several fuel-burning appliances
competing for limited internal air; 4) loose vent pipe connections from fuel-fired appliances; 5) obstructions, or unconventional vent pipe designs which can amplify the above situations; 6) poorly designed and maintained chimneys and/or
vents; ii) extended operation of unvented fuel-burning devices
(range, oven, fireplace, etc.); iii) temperature inversions which
can trap exhaust near the ground; and iv) car idling in an
open or closed attached garage, or near a home.
9
•
When wall mounting, place out of the reach of children.
Under no circumstance should children be allowed to
handle the CO alarm.
•
Install in a sleeping area.
•
Placing at eye level allows for optimum monitoring of
the digital display.
•
Insure that all vents of the unit are unobstructed.
•
For tabletop mounting we recommend the unit be
placed no higher than three feet from the floor.
WARNING: The installation of this device should not be used as a substitute for proper installation, use, and maintenance of fuel-burning
appliances, including appropriate ventilation and exhaust systems.
8
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 10
Features and Operation of Digital Display Model
F e a t u res and Operation of Digital Display Model (continued)
Your new Kidde Battery Powered CO Alarm utilizes sophisticated
electronic components to protect you and your family from the
dangers of CO.
Other Possible Displays and Their Meanings
Unique features include a digital display capable of displaying CO
concentrations in (PPM) Parts Per Million and the highest levels
of CO detected. Familiarize yourself with these features:
Digital Display Backlight Feature
To help see the displayed reading in the dark, a backlight appears
when the peak level button is pressed.
Digital Display - Shows CO level in PPM
Your Kidde CO alarm continuously displays a digital readout of
the CO level in Parts Per Million (PPM). The digital display is
capable of detecting and displaying readings between 30 and 999
(PPM). A reading of 0 PPM is expected under
normal conditions
(see figure 2).
Figure 2
You will become accustomed to glancing at the
display in much the same manner as you look at a thermometer
or clock. The unit will not automatically display reading below 30
PPM. However, readings between 11 and 999 PPM will be stored
in the Peak Level Memory.
The following symbols will appear on the display during
normal or error operations, and are explained below.
Normal Operation
Normal operation (see figure 3) with a full b a t t e ry.
The dot in the lower right corner cycles on and off
every 5 seconds. If CO is present the display will
indicate the reading in Parts Per Million (PPM).
Figure 3
Normal Operation following Power-up or Reset
Figure 4 shows the normal display immediately
after installing batteries or after the test/reset
button is pressed. The display should change to the
normal display (see figure 3) approximately
30 seconds after pressing the test/reset button.
(see Test/Reset Button page 13).
Figure 4
If the test/reset button is pressed, the alarm will sound. The display
will show a number during the time that the alarm is sounding.
This number is a normal part of the test function, and does
not indicate a CO reading.
Peak Level Display
When the peak level button is pressed and held,
the display shows the highest CO reading taken
by the CO alarm since its last peak level reset or
power-up(Example shown in Figure 5). The
backlight will illuminate for several seconds after
the peak level button is pressed to help see the
reading.
Figure 5
Although the peak level feature will display levels below 30 PPM,
these levels will not result in an alarm no matter how long the
device is exposed to these levels.
10
11
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 12
Features and Operation of Digital Display Model (continued)
F e a t u res and Operation for Digital Display Model (continued)
Peak Level Display (Continued)
Resetting the Peak Level Reading
The peak level feature is helpful in identifying low level CO occurrences below 30 PPM. Although the unit will not automatically
display levels below 30 PPM, it will detect and store these readings in memory. By pressing the peak level button, concentration
levels as low as 11 and up to 999 PPM will be displayed.
To reset or clear the peak level reading, press and hold the peak
level button and then press and hold the test/reset button at the
same time. The number on the display will return to 0 PPM. C O
concentrations displayed below 30 PPM in memory are for reference only and the accuracy of the concentration shown may
not be as accurate as noted on page 26.
Concentrations of CO between 0 and 30 PPM can often occur in
normal, everyday conditions. Concentrations of CO below 30 PPM may
be an indication of a transient condition that may appear today and
never reappear. Just a few examples of conditions and/or sources
that may cause low level readings are heavy automobile traffic, a
running vehicle in an attached garage, an appliance that emits CO
when starting up, a fire in a fireplace or charcoal in a nearby barbecue.
A temperature inversion can trap CO generated by traffic and other
fuel burning appliances causing readings of CO.
Some CO conditions may start out as low level leaks but could
develop into CO concentrations that could become harmful. If this
happens, the CO alarm will detect the dangerous level and alarm,
notifying you and others of the conditions. DO NOT ignore high
concentration readings above 30 PPM or a CO alarming device
that is in alarm. Refer to page 18 for more details.
Note: The peak level reading will also be reset when the
batteries are removed.
Unit Malfunction
In the rare event that your alarm malfunctions,
it will alert you with a short “chirp” and the red
LED will flash once every 30 seconds. The
Figure 6
digital model will display “Err” as shown in
Fig. 6.
Seven years after initial power up, this unit will "chirp" every
30 seconds to indicate that it is time to replace the alarm.
The unit will not detect CO in this condition. Please replace
immediately.
Note: Your Kidde CO Alarm will NOT monitor CO levels while an
error warning is being displayed.
Low Battery
If the batteries become “low”, the alarm will
Figure 7
alert you with a short “chirp” and the red LED
will flash once every 30 seconds for up to 7 days.
The digital models will display “Lb” as shown in Fig. 7.
12
13
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 14
Features and Operation of Digital Display
and Non-digital Display Models (continued)
Features and Operation of Digital Display and
Non-Digital Display Models (continued)
Test/Reset Button
Lights
The test/reset button is used to test the unit’s electronics and to
reset the unit during alarm.
Red Alarm Light
•
Test the unit:
To test, press the test/reset button. Test the unit weekly!
The unit will perform a self diagnostic test by cycling through the
alarm pattern.
Familiarize yourself and family members with the alarm pattern.
A CO alarm is 4 short beeps – followed by 5 seconds of silence –
followed by 4 short beeps. This cycle will repeat in the event of a
CO alarm. This cycle will continue for the first 4 minutes of a CO
alarm and then change to one cycle every one minute until the
device is reset or the CO is eliminated.
Note: For Digital Display Models
After the test/reset button is pressed, numbers appear on the
display. These are not CO readings and are part of the internal
testing process. Ignore these numbers !
Due to the loudness of the a l a rmwe suggest you place your fingers
over the sounder opening when testing your Kidde CO Alarm.
•
The red light flashing once every
30 seconds, accompanied by the
alarm “chirp”, indicates the
batteries need to be replaced, or
the unit has malfunctioned (see figure 8).
Figure 8
4 quick flashes with alarm – followed by 5 seconds off –
followed by 4 quick flashes with alarm (repeating pattern)
indicates the p resence of carbon monoxide. Refer to pages 1820 for instructions on What to do if the Alarm Sounds.
Green Operate Light
The green light indicates the unit is
functioning properly (see figure 9).
The green light will flash every 30 seconds indicating a CO reading is being
taken and when any button
is pressed.
Figure 9
Reset
If the alarm is sounding, pressing the test/reset button will terminate
the alarm. If the CO condition that caused the alert in the first
place continues, the alarm will reactivate. If the CO alarm sounds
again within six minutes, it is sensing high levels of CO which
can quickly become a dangerous situation.
If this happens follow What To Do If The Alarm Sounds on pages
18-20. Reactivation times depend on the amount of CO that caused
the CO alarm to initially alarm and the amount of CO present after
resetting the alarm.
14
15
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 16
Battery Installation/Replacement
Battery Installation/Replacement
Installation/Replacement
Battery Replacement/Installation Instructions
Since batteries are not installed in the unit at the factory, you will
need to install them.
To install or replace the batteries in your Kidde unit please perform the following steps:
Three AA batteries have been included with your purchase. When
replacing the batteries, we recommend use of the following for a
minimum of one year normal operation:
•
•
Duracell MN1500
•
Rayovac 815
Energizer E91
These batteries can be purchased at your local retailer.
Note: Constant exposure to high or low humidity may reduce
battery efficiency.
NOTE: Your Kidde CO alarm will NOT monitor CO levels during
the time that the "Low Battery" warning or error warning is
being displayed.
(continued)
1. Gently flip open
the lower half of
the front cover to
expose the battery
compartment.
2. Remove the old
batteries and properly
dispose of them as
recommended by the
b a t t e ry manufacture r
(see figure 10).
Figure 10
3. Reinstall the new batteries, being careful to seat
the red battery warning flags in the recess of the
battery well. Also, note the polarity illustration in
the bottom of the battery compartment. If applicable, the
unit will chirp and display
for approximately one
minute and re t u rn to normal operation.
4. Gently close the bottom cover. The bottom cover of
your CO alarm will NOT close if all three AA
batteries are not properly installed.
16
17
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 18
Part Four – What to do When the
Alarm Sounds
What To Do If The Alarm Sounds (continued)
Symptoms of CO Poisoning
Carbon Monoxide Alarm Procedure
WARNING: Actuation of the CO Alarm
indicates the presence of Carbon Monoxide
(CO) which can kill you.
The following common symptoms are related to carbon monoxide
poisoning and should be discussed with ALL members of the
household. Learn the difference between mild, medium and
extreme levels.
Caution: This CO alarm will only indicate the presence of CO at
the sensor. CO may be present in other areas.
If alarm signal sounds 4 quick beeps, 5 seconds off:
1) Immediately move to fresh air - outdoors or by an
open door or window. Check that all persons are
accounted for. Do not re-enter the premises or
move away from the open door/window until
emergency services responders have arrived, the
premises have been aired out, and your alarm
remains in its normal operating condition.
2) Call your emergency local service
(fire deptartment or 911).
PHONE NUMBER
Never restart the source of a CO problem until it has
been corrected. Never ignore the sound of the alarm!
18
Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as “Flu-like” symptoms).
Medium Exposure: Severe throbbing headache, drowsiness,
confusion, fast heart rate.
Extreme Exposure:
Unconsciousness, convulsions, cardiorespiratory failure, death.
Many cases of reported CARBON MONOXIDE POISONING
indicate that while victims are aware they are not well, they
become so disoriented they are unable to save themselves by
either exiting the building or calling for assistance. Young
children and household pets are typically the first affected.
If you experience even mild symptoms of CO poisoning, consult
your doctor immediately!
19
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 20
What To Do If The Alarm Sounds (continued)
Because carbon monoxide is a cumulative poison, long-term exposures to low levels may cause symptoms, as well as short-term
exposures to high levels. This Kidde unit has a time-weighted
a l a rm- the higher the level of carbon monoxide present, the sooner
the alarm will be triggered.
This CO alarm can only warn you of the presence of CO. It does
not prevent CO from occurring, nor can it solve an existing CO
problem. If your unit has alarmed and you’ve provided ventilation by leaving your windows and doors open, the CO buildup
may have dissipated by the time help responds. Although your
problem may appear to be temporarily solved, it’s crucial that the
source of the CO is determined and that the appropriate repairs
are made.
This CO alarm meets the alarm response time re q u i rements as follows:
At 70 PPM, the unit must alarm within 60-240 minutes
At 150 PPM, the unit must alarm within 10-50 minutes
At 400 PPM, the unit must alarm within 4-15 minutes
Caring for your Kidde Battery Powered
CO Alarm
To keep your CO alarm in good working order, please
follow these simple steps:
•
Verify unit alarm, lights and battery operation by pushing
the test button once a week.
•
Vacuum the CO alarm cover with a soft brush attachment
once a month to remove accumulated dust.
•
Instruct children never to play with the CO alarm. Warn
children of the dangers of carbon monoxide poisoning.
•
•
Never use detergents or other solvents to clean the CO alarm .
•
Do not paint the CO alarm. Paint will seal the vents and
interfere with the sensor ability to detect CO.
•
Do not place near a diaper pail.
Avoid spraying air fresheners, hair spray, paint or other
aerosols near the CO alarm.
WARNING
This product is intended for use in ordinary indoor residential
areas. It is not designed to measure compliance with commercial
and industrial standards.
This device is designed to protect individuals from acute effects
of of carbon monoxide exposure. It may not fully safeguard individuals with specific medical conditions. If in doubt, consult a
medical practitioner. Individuals with medical problems may consider using warning devices, which provide audible and visual signals for carbon monoxide concentrations under 30 ppm.
20
21
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 22
Caring for your Kidde Battery Powered
CO Alarm (continued)
Move the CO alarm and place in another location prior to performing any of the following:
•
•
•
•
Staining or stripping wood floors or furniture
Painting
Troubleshooting Guide
Symptom
1 chirp every 30 seconds with a red LED
flash, digital units
display
Problem
Batteries are low
and need replacing.
Action
See pages 16-17.
Battery Installation/
Replacement.
Wall papering
Using adhesives
Storing the unit in a plastic bag during the above projects will
protect the sensor from permanent damage.
WARNING: As soon as possible, place the CO alarm back in its
proper location to assure continuous protection from Carbon
Monoxide poisoning.
Accommodation spaces should be well ventilated when household
cleaning supplies or similar contaminants are used.
1 chirp every 30 seconds with a red LED
flash, digital units
display
No display, constant
alarm and red light.
Sensor or unit
malfunction.
Microprocessor failure.
Replace unit,
if necessary
Unit has malfunctioned. Replace unit.
The following substances can affect the sensor and may cause
false readings:
Methane, propane, iso-butane, iso-propanol, ethylene, benzene,
toluene, ethyl acetate, hydrogen sulfide, sulfur dioxides, alcohol
based products, paints, thinners, solvents, adhesives, hair
sprays, after shaves, perfumes, and some cleaning agents.
The problems listed above are under normal operation conditions. Other
error (Err) conditions could exist if, for instance, ambient conditions are
outside normal operating range (see page 26), battery condition is less
than optimal, etc. If you still have any additional questions regarding Err
conditions, please call our Consumer Hotline at 1-800-880-6788.
22
23
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 24
Frequently Asked Questions
Q. How many CO alarms do I need?
A. There is no formula for determining how many CO
Wall Mounting Template
If you are going to mount your Kidde CO Alarm to the wall, you
may use this template for exact placement of the two wall mount
screws provided. For more information about mounting to the wall,
please refer to page 8.
a l a rms you will need. It all depends on the layout of your home,
how many bedrooms you have, where the heat sources are,
and where the fuel-burning appliances are located. The
Consumer Product Safety Commission (CPSC) recommends
installing at least one carbon monoxide alarm with an audible
w a rning signal near the sleeping area.
Q. Do I have to press the test button to get a CO reading?
A. No. Your Kidde CO alarm continuously monitors the air
for carbon monoxide. The CO alarm will alert you to the pre sence of CO automatically. To test the internal components and circ u i t ry of your CO alarm, press the test/reset button.
24
25
810-2263_RevA_146_MAN_ENG
4/14/04
3:29 PM
Page 26
Product Specifications
POWER:
SENSOR:
Three AA batteries (supplied)
Electrochemical carbon monoxide sensor
ACCURACY:
Each Kidde CO Alarm is calibrated to a CO concentration of 150 ppm (+/-25 ppm) in air, at 80°F
(+/-10°F) and 40% (+/-3%) relative humidity.
Depending on the ambient condition (temperature, humidity) and the condition of the sensor,
the alarm readings may vary. The digital reading
tolerances are: Ambient: 80°F(+/-10°F), atmospheric
pressure +/-10%, 40%+/-3% relative humidity.
READING
TOLERANCE (OF DISPLAY READING)
0-999ppm
+20% +15ppm
TEMPERATURE: Operating range 40°F (4.4°C) to
100°F (37.8°C)
MOUNTING: Accessories supplied for wall mounting
and table top applications
ALARM: 85+ dB at 10' @ 3.4 ± 0.5 KHz pulsing alarm
SIZE
& WEIGHT: 5.5" diameter x 1.4" depth/0.66 lbs.
with batteries
WARRANTY: Five-year limited warranty from date
of purchase against defects in material
and workmanship on the CO Alarm unit.
Limited Wa rranty
WARRANTY COVERAGE: THE MANUFACTURER WARRANTS TO THE ORIGINAL
CONSUMER PURCHASER, THAT THIS ALARM WILL BE FREE OF DEFECTS IN
MATERIAL AND WORKMANSHIP FOR A PERIOD OF FIVE (5) YEARS FROM DATE
OF PURCHASE. THE MANUFACTURER’S LIABILITY HEREUNDER IS LIMITED TO
REPLACEMENT OF THE PRODUCT, REPAIR OF THE PRODUCT OR REPLACEMENT OF THE PRODUCT WITH REPAIRED PRODUCT AT THE DISCRETION OF
THE MANUFACTURER. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN
DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLECT, TAMPERING OR
OTHER CAUSES NOT ARISING FROM DEFECTS IN MATERIAL OR WORKMANSHIP. THIS WARRANTY EXTENDS TO THE ORIGINAL CONSUMER PURCHASER
OF THE PRODUCT ONLY.
Warranty Disclaimers: Any implied warranties arising out of this sale, including but not limited to the implied warranties of description, merchantability and
fitness for a particular purpose, are limited in duration to the above warranty
period. In no event shall the Manufacturer be liable for loss of use of this pro duct or for any indirect, special, incidental or consequential damages, or costs,
or expenses incurred by the consumer or any other user of this product,
whether due to a breach of contract, negligence, strict liability in tort or otherwise. The Manufacturer shall have no liability for any personal injury, property
damage or any special, incidental, contingent or consequential damage of any
kind resulting from gas leakage, fire or explosion.
Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above limitations or exclusions may not apply to you.
Legal Remedies: This warranty gives you specific legal rights and you may
also have other rights that vary from state to state.
Wa rranty Perf o rmance: During the above warranty period, your product will
be replaced with a comparable product if the defective product is returned,
postage prepaid, to KIDDE , Customer Service Department, 1394 South Third
S t reet, Mebane, NC 27302, together with proof of purchase date. Please
include a note describing the problem when you re t u rn the unit. The re p l a c ement product will be in warranty for the remainder of the original warranty
period or for six months, whichever is longer. Other than the cost of postage,
no charge will be made for replacement of the defective product.
26
27
810-2263_RevA_146_MAN_ENG
Limited Wa rranty
4/14/04
3:29 PM
Page 28
(continued)
Notes
Important: Do not remove back cover. Back cover removal will
void warranty.
Your Kidde Carbon Monoxide Alarm is not a substitute for property, disability, life or other insurance of any kind. Appropriate insurance coverage is your responsibility. Consult your insurance agent.
Also, Kidde makes no warranty, express or implied, written or
oral, including that of merchantability or fitness for any particular
purpose, with respect to the batteries.
The above warranty may not be altered except in writing signed
by both parties hereto.
Please send products and all other correspondence to:
Kidde / Pyrene Corp.
Attn.: Customer Service Department
130 Esna Park Drive, Markham, ON, L3R 1E3
Consumer Hotline: 1-800-880-6788
www.kidde.ca
For Warranty Service:
In many cases the quickest way to exchange your CO alarm is to
re t u rn it to the original place of purchase. If you have questions,
call the KIDDE customer service department at
1-800-880-6788 for assistance.
28
29