User manual | Escali Plena Scale User Manual

Precision Weighing Solutions
User Manual
Plena Digital Kitchen Scale
Thank you for purchasing an
Escali Digital Scale.
Please read the following operation information to ensure the
proper function of your new scale.
Before use
Your scale is equipped with one easy to use all feature operating
button. This button is located on the front of the scale, just below the
display. With this button, you control all features; On, Off, Tare and
Weighing Mode (g / kg / lb oz / oz).
How to weigh:
1) Turn the scale on. All display segments will appear for
approximately 2 seconds before resetting to zero.
2) Your scale will keep the last used weighing mode in memory, and
will return automatically to this mode when you turn the scale on.
3) Place item slowly on the platform.
How to use the “Tare” feature:
This feature allows the display to be reset to zero after you weigh an
item in the bowl. It shows the weight of additional items as if you were
to weigh them separately.
1) Turn the scale on with the bowl on the platform.
2) Put an item in the bowl. The display will show its weight.
3) Press the Operating button again. Wait 2 seconds, the weight of
the bowl with item will be removed and the display will reset to “0.0”.
4) Slowly add another item to the bowl. The display will show the
weight of the new item only.
5) Repeat step 3 and 4 when adding more items to the bowl.
1) All feature operating button
2) Weighing platform
How to clear the “Tare” feature:
1) Remove all items from the platform.
2) Press the Operating button once. Wait 2 seconds.
Now the scale is reset to “0.0” and the weight of all items on the
platform will be displayed.
Turning off your scale:
Additional Information
Your scale will automatically turn of after 2 minutes of non-use. You
can also manually turn of the scale by holding the Operating button
down for approximately 3 seconds.
1) Make sure your scale is at room temperature and on a stable
horizontal surface free of vibration.
2) This scale is not waterproof. Do not expose to moisture.
3) As this scale is a precision instrument, it must be handled with
extreme care. Avoid rough treatment, shaking and vibration.
4) Do not disassemble this scale or the warranty will be void.
5) The display value may be affected by electromagnetic
disturbances such as operating near a radio. If this occurs, move the
device that is causing the disturbance and turn the scale off and
Changing the Weighing Mode:
Your scale can weigh in grams, ounces, Pounds/Ounces or
Kilograms/grams. The factory default is set to grams. You can simply
change the weighing mode before you operate the scale.
1) Turn the scale on.
2) Immediately press the Operating button once, or multiple times,
until the desired weighing mode is displayed.
3) Your scale will keep the last used weighing mode in memory, and
will return automatically to this mode when you turn the scale on.
Do not place overweight items on the scale
Weighing items over the maximum weight capacity will cause an
overload “O-L.d” error to display. Immediately remove overweight
items to avoid causing damage to your scale.
Power Source: two 3-volt lithium batteries
Dimensions: 8.75" x 7.25" x 1.5" (22.5cm x 18.5cm x 4cm)
Increments: 0.1oz (1/10th oz) & 1 (one gram)
Capacity: 13 Lb / 6 Kg
Bowl Capacity: 2.5 Liter / 85 Fl. Oz.
Weight Modes: grams, ounces, Kg/gm, and lb./oz.
Auto Shut Off: Turns off after 2 minutes of non-use.
Warranty: Manufacturer’s five (5) year warranty, see for full details.
Battery Replacement/Installation:
Replace the batteries when the LCD display reads “LO”.
1) Remove the battery door.
2) Install two new 3-volt lithium batteries.
3) Replace the battery door.
Escali’s liability is limited to two (2) times the cost of the product
© Copyright Escali LLC, 2003
Download PDF