Escient M51003-02A7 Car Video System User Manual

Operating Instructions
Projector Operations
LCD Projector  
Model No.
Commercial Use
PT-TW231RU
Thank you for purchasing this Panasonic Product.
JJ Before operating this product, please read the instructions carefully and save this manual
for future use.
For information on using the product via a network, refer to “Operating Instructions – Network
Operations”.
ENGLISH
KY4AC
Read
Read thisthis
first! first!
WARNING:
Important
Information
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
Power Supply:
This Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current only.
CAUTION:
The AC power cord which is supplied with the projector as an accessory can only be used for
power supplies up to 125 V, 10 A. If you need to use higher voltages or currents than this, you will
need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire
may result.
WARNING:
RISK OF ELECTRIC SHOCK, DO NOT OPEN.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
CAUTION:
This equipment is equipped with a three-pin grounding-type power
plug. Do not remove the grounding pin on the power plug. This plug
will only fit a grounding-type power outlet. This is a safety feature. If
you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
WARNING:
TURN OFF THE UV LAMP BEFORE OPENING THE LAMP COVER.
2 - ENGLISH
Do not remove
Read this first!
Declaration of Conformity
Model Number: PT-TW231RU
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Address:
One Panasonic Way, Secaucus, NJ 07094
Telephone number: (877)803-8492
E-mail: projectorsupport@us.panasonic.com
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make any unauthorized
modifications.
Important
Information
FCC NOTICE (USA)
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
•• Reorient or relocate the receiving antenna.
•• Increase the separation between the equipment and receiver.
•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference” available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and the user
must use only shielded interface cables when connecting to host computer or peripheral devices. Also, any
unauthorized changes or modifications to this equipment could void the user’s authority to operate this device.
NOTIFICATION (Canada)
This class B digital apparatus complies with Canadian ICES-003.
WARNING:
•• Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
•• For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the
building installation wiring.
•• For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily
accessible.
NOTICE U.S.A. only:
•• This product has a High Intensity Discharge (HID) lamp that contains mercury. Dispose may be regulated
in your community due to environmental considerations. For disposal or recycling information, please visit
Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.
ENGLISH - 3
Read this first!
Important
Information
WARNING:
„„ POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily
accessible when problems occur. If the following problems occur, cut off the power supply
immediately.
Continued use of the projector in these conditions will result in fire or electric shock.
zz If foreign objects or water get inside the projector, cut off the power supply.
zz If the projector is dropped or the cabinet is broken, cut off the power supply.
zz If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or fire will result.
zz Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Insert the power plug securely into the wall outlet.
If the plug is not inserted correctly, electric shocks or overheating will result.
zz Do not use anything other than the provided power cord.
zz Do not use the provided power cord for other electrical equipment.
zz Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a fire.
zz If dust builds up on the power plug, the resulting humidity can damage the insulation.
zz If not using the projector for an extended period of time, pull the power plug out from the wall outlet.
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
Do not handle the power plug with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and fire will result.
„„ ON USE/INSTALLATION
Do not place liquid containers on top of the projector.
If water spills onto the projector or gets inside it, fire or electric shocks will result.
If any water gets inside the projector, contact an Authorized Service Center.
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, fire or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into
contact with oily smoke or steam, ex. a bathroom.
Using the projector under such conditions will result in fire, electric shocks or components deterioration.
Components deterioration (such as ceiling mount brackets) may cause the projector which is mounted on the
ceiling to fall down.
Do not install this projector in a place which is not strong enough to take the full weight of the
projector or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage
could result.
Do not place another projector or other heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or
injury. The projector will be damaged or deformed.
4 - ENGLISH
WARNING:
Installation work (such as ceiling mount bracket) should only be carried out by a qualified technician.
If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.
zz Do not use anything other than an authorized ceiling mount bracket.
zz Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the
projector from falling down. (Install in a different location to the ceiling mount bracket)
Important
Information
Read this first!
Do not cover the air inlet port or the air outlet port.
Doing so will cause the projector to overheat, which can cause fire or damage to the projector.
zz Do not place the projector in narrow, badly ventilated places such as closets or bookshelves.
zz Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.
Do not place your hands or other objects close to the air outlet port.
Doing so will cause burns or damage your hands or other objects.
zz Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot
withstand heat close to this port.
Do not look and place your skin into the lights emitted from the lens while the projector is being used.
Doing so can cause burns or loss of sight.
zz Strong light is emitted from the projector’s lens. Do not look or place your hands directly into this light.
zz Be especially careful not to let young children look into the lens. In addition, turn off the power and
disconnect the power plug when you are away from the projector.
Do not insert any foreign objects into the projector.
Doing so will cause fire or electric shocks.
zz Do not insert any metal objects or flammable objects into the projector or drop them onto the projector.
Never attempt to remodel or disassemble the projector.
High voltages can cause fire or electric shocks.
zz For any inspection, adjustment and repair work, please contact an Authorized Service Center.
Do not project an image with the lens cover attached.
Doing so can cause fire.
Do not allow metal objects, flammable objects, or liquids to enter inside of the projector. Do not allow
the projector to get wet.
Doing so may cause short circuits or overheating, and result in fire, electric shock, or malfunction of the
projector.
zz Do not place containers of liquid or metal objects near the projector.
zz If liquid enters inside of the projector, consult your dealer.
zz Particular attention must be paid to children.
Use the ceiling mount bracket specified by Panasonic.
Defects in the ceiling mount bracket will result in falling accidents.
zz Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.
Be sure to ask authorized personnel or your supplier when mounting the product to a ceiling.
This requires an optional ceiling mount bracket.
Model No.: E
T-PKV100H (for high ceilings), ET-PKV100S (for low ceilings),
ET-PKT100B (Projector Mount Base).
ENGLISH - 5
Read this first!
Important
Information
WARNING:
„„ ACCESSORIES
Do not use or handle the batteries for remote control, interactive pointer and interactive light pen
improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire.
zz Do not use unspecified batteries.
zz Do not disassemble dry cell batteries.
zz Do not heat the batteries or place them into water or fire.
zz Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as
necklaces or hairpins.
zz Do not store batteries together with metallic objects.
zz Store the batteries in a plastic bag and keep them away from metallic objects.
zz Make sure the polarities (+ and -) are correct when inserting the batteries.
zz Do not use a new battery together with an old battery or mix different types of batteries.
zz Do not use batteries with the outer cover peeling away or removed.
zz Remove the empty batteries from the remote control at once.
zz Insulate the battery using tape or something similar before disposal.
Do not allow children to reach the batteries (AAA/R03 type).
zz The battery can cause personal injury if swallowed.
zz If swallowed, seek medical advice immediately.
If the battery fluid leaks, do not touch it with bare hands, and take the following measures if necessary.
zz Battery fluid on your skin or clothing could result in skin inflammation or injury.
Rinse with clean water and seek medical advice immediately.
zz Battery fluid coming in contact with your eyes could result in loss of sight.
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will
result.
zz The lamp can easily explode if struck against hard objects or dropped.
zz Before replacing the lamp, be sure to disconnect the power plug from the wall outlet.
Electric shocks or explosions can result if this is not done.
zz When replacing the lamp, turn the power off and allow the lamp it to cool for at least 1 hour before handling
it otherwise it can cause burns.
Do not allow infants or pets to touch the remote control unit.
zz Keep the remote control unit out of the reach of infants and pets after using it.
Do not use the supplied power cord with devices other than this projector.
zz Using the supplied power cord with devices other than this projector may cause short circuits or
overheating, and result in electric shock or fire.
Remove the depleted batteries from the remote control promptly.
zz Leaving them in the unit may result in fluid leakage, overheating, or explosion of the batteries.
6 - ENGLISH
CAUTION:
„„ POWER
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric
shocks will result.
Important
Information
Read this first!
When not using the projector for an extended period of time, disconnect the power plug from the wall
outlet and remove the batteries from the remote control.
Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.
Electric shocks can result if this is not done.
„„ ON USE/INSTALLATION
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
zz Be especially careful not to let young children stand or sit on the projector.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in fire.
zz Take particular care in locations exposed to direct sunlight or near stoves.
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause fire or electric shocks
to occur.
Never plug headphones and earphones into AUDIO OUT jack.
Excessive sound pressure from earphones and headphones can cause hearing loss.
„„ ACCESSORIES
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the
broken pieces.
Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which
contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces will cause injury.
zz If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek
medical advice immediately.
zz Ask your dealer about replacing the lamp unit and check the inside of the projector.
ENGLISH - 7
Read this first!
Important
Information
Brazil Only
Brasil Apenas
„„ Manuseio de baterias usadas
BRASIL
Após o uso, as pilhas e /ou baterias poderão
ser entregues ao estabelecimento comercial
ou rede de assistência técnica autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma fita isolante adesiva, antes de depositar numa caixa
destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper
a blindagem e produzir fogo.
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a
garganta, danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo
devido ao curto circuito dos terminais.
Não incinere nem aqueça as baterias, elas não podem ficar expostas a temperaturas superiores a 100 °C (212
°F). O gás liberado pela bateria pode irritar a garganta,
danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao
curto circuito dos terminais provocado internamente.
Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante
água. Caso haja irritação, consulte um médico.
„„ Remoção das baterias
„„ Baterias de controle remoto
Pressione a guia e levante a tampa.
„„ Ponteiro interativo e baterias para caneta óptica
Gire conforme é apresentado nas figuras a seguir.
Trademarks
•• HDMI, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI
Licensing LLC.
•• Other names, company names or product names used in these operating instructions are the trademarks or
registered trademarks of their respective holders.
Please note that the operating instructions do not include the ® and TM symbols.
Illustrations in these operating instructions
•• Note that illustrations of the projector and screens may differ from the ones you actually see.
Page references
•• In these instructions, references to pages are indicated as: (Æ page 00).
Term
•• In these instructions, the “Wireless remote control unit” accessory is referred to as the “Remote control”.
8 - ENGLISH
Auto Setup Function
This function enables Input search
and Auto PC adj. by pressing the
<AUTO SETUP> button on the
remote control.
Direct Power Off Function
With the Direct Power Off function,
you can disconnect the power cord
from the wall outlet or turn off the
breaker even during projection.
Improved connectivity
The inclusion of an HDMI terminal
provides support for high quality
video and HDMI audio.
Useful Functions for Presentations
The digital zoom function allows you
to focus on the crucial information
during a presentation.
JJQuick steps
For details, see the corresponding pages.
1. Set up your projector.
(Æpage 22)
2. Connect with other devices.
(Æpage 25)
3. Connect the power cord.
(Æpage 26)
4. Power on.
(Æpage 28)
5. Select the input signal.
(Æpage 31)
Interactive Function
This projector has the interactive
software and tools.
The interactive function allows
you to write and draw on a virtual
whiteboard by using the interactive
pen or pointer.
6. Adjust the image.
(Æpage 31)
ENGLISH - 9
Contents
Be sure to read “Read this first!”. (
Important
Information
Important Information
Read this first!............................................ 2
Contents.................................................... 10
Precautions for Use................................. 12
Preparation
Cautions when transporting........................................... 12
Cautions when installing................................................ 12
Security......................................................................... 13
Disposal......................................................................... 13
Cautions on use............................................................ 14
Accessories................................................................... 15
Optional accessories..................................................... 16
Getting Started
Preparation
About Your Projector............................... 17
Basic Operation
Remote control.............................................................. 17
Projector body............................................................... 18
Interactive Function....................................................... 18
Control panel ................................................................ 19
Indicators....................................................................... 19
Side terminals................................................................ 20
Using Remote control.............................. 21
Installing and Removing batteries................................. 21
Setting Remote control ID numbers.............................. 21
Getting Started
Setting up.................................................. 22
Settings
Projection method......................................................... 22
Parts for ceiling mount (Optional).................................. 22
Screen size and throw distance.................................... 23
Adjusting front adjustable feet....................................... 24
Connections.............................................. 25
Before connecting to the projector................................ 25
Connecting example...................................................... 25
Maintenance
Basic Operation
Powering ON/OFF..................................... 26
Appendix
Connecting the power cord........................................... 26
ON(G)/STANDBY(R) indicator...................................... 27
Turning On the Projector............................................... 28
Enter a PIN code........................................................... 29
Turning Off the Projector............................................... 30
Projecting.................................................. 31
Selecting the image....................................................... 31
How to adjust the state of the image............................. 31
10 - ENGLISH
pages 2 to 8)
Basic operations by using the remote
control................................................... 32
Using the Auto setup function........................................ 32
Switching the input signal.............................................. 32
Using the SCREEN button............................................ 32
Using the KEYSTONE button........................................ 33
Using the INFO. button.................................................. 33
Using the FREEZE function.......................................... 33
Using the AV MUTE function......................................... 34
Using the P-TIMER button............................................ 34
Using the LAMP button................................................. 34
Using the D.ZOOM buttons........................................... 34
Controlling the volume of the speaker........................... 34
Using the IMAGE button................................................ 35
Using the MUTE button................................................. 35
Settings
Menu Navigation....................................... 36
Navigating through the menu........................................ 36
Main menu..................................................................... 37
Sub menu...................................................................... 37
Input menu................................................ 39
Computer 1: RGB/Component /RGB (Scart) ............... 39
Computer 2: RGB.......................................................... 39
HDMI............................................................................. 39
Video............................................................................. 39
S-video.......................................................................... 39
AUTO PC adjust........................................ 41
Auto PC adj................................................................... 41
Manual PC adjust...................................... 42
Fine sync....................................................................... 42
Total dots....................................................................... 42
Horizontal...................................................................... 42
Vertical........................................................................... 42
Current mode................................................................ 43
Clamp............................................................................ 43
Display area H............................................................... 43
Display area V............................................................... 43
Reset............................................................................. 43
Mode free...................................................................... 43
Store.............................................................................. 43
Image select ............................................. 44
Dynamic........................................................................ 44
Standard........................................................................ 44
Real............................................................................... 44
Cinema.......................................................................... 44
Blackboard(Green)........................................................ 44
Colorboard..................................................................... 44
Image 1-4...................................................................... 44
Normal........................................................................... 48
Full. ............................................................................... 48
Wide(16:9)..................................................................... 48
Zoom............................................................................. 48
True................................................................................ 48
Natural wide.................................................................. 48
Custom.......................................................................... 48
Custom adj.................................................................... 49
Digital zoom +............................................................... 49
Digital zoom -................................................................ 49
Keystone....................................................................... 49
Ceiling........................................................................... 50
Rear............................................................................... 50
Screen aspect .............................................................. 50
Reset............................................................................. 50
Sound........................................................ 51
Volume.......................................................................... 51
Mute.............................................................................. 51
Maintenance
LAMP and WARNING Indicators............. 61
Managing the indicated problems................................. 61
Preparation
Input Source Information Display ................................. 60
Replacement............................................. 62
Before replacing the unit............................................... 62
Maintenance.................................................................. 62
Replacing the unit.......................................................... 63
Attaching the Lens Cover.............................................. 66
Attaching the Cable Holder and Ferrite Core................ 66
Troubleshooting....................................... 67
Appendix
Technical Information.............................. 69
Serial terminal............................................................... 69
Other terminals.............................................................. 72
List of compatible signals.............................................. 73
Specifications........................................... 77
Getting Started
Screen ...................................................... 48
Information................................................ 60
Basic Operation
Contrast......................................................................... 45
Brightness..................................................................... 45
Color.............................................................................. 45
Tint. ............................................................................... 45
Color temp..................................................................... 45
Red. ............................................................................... 46
Green............................................................................ 46
Blue .............................................................................. 46
Sharpness..................................................................... 46
Gamma.......................................................................... 46
Noise reduction............................................................. 46
Progressive................................................................... 47
Reset............................................................................. 47
Store.............................................................................. 47
Fan control.................................................................... 58
Video delay control........................................................ 58
Lamp runtime................................................................ 58
Filter counter................................................................. 58
Warning log................................................................... 59
Factory default............................................................... 59
Dimensions.................................................................... 79
Ceiling mount bracket safeguards......... 79
Index.......................................................... 80
Setting....................................................... 52
Appendix
Maintenance
Language...................................................................... 52
Menu position................................................................ 52
Auto setup..................................................................... 52
Background................................................................... 53
Display........................................................................... 53
Logo.............................................................................. 53
HDMI setup................................................................... 54
Terminal......................................................................... 54
Power management...................................................... 54
Direct on........................................................................ 55
Standby mode............................................................... 55
P-timer........................................................................... 55
Closed caption............................................................... 56
Lamp power................................................................... 56
Remote control.............................................................. 56
Security......................................................................... 57
Fan. ............................................................................... 57
Settings
Image adjust............................................. 45
Important
Information
Contents
ENGLISH - 11
Precautions for Use
Important
Information
Cautions when transporting
zz When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.
Doing so may damage the internal parts and result in malfunctions.
zz Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
Cautions when installing
JJ Do not set up the projector outdoors.
zz The projector is designed for indoor use only.
JJ Do not use under the following conditions.
zz Places where vibration and impacts occur such as in a car or vehicle: Doing so may damage the internal parts
and result in malfunctions.
zz Near the exhaust of an air conditioner or near lights (studio lamps, etc.) where temperature changes greatly
(Operating environment Æpage 78): Doing so may shorten the life of the lamp or result in deformation of the
outer case and malfunctions.
zz Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
JJ Do not install the projector at elevations of 2700 m (8858 ft) or higher above
sea level.
Failure to do so may shorten the life of the internal parts and result in malfunctions.
JJ Do not use the projector installed vertically or tilted right or left (Æpage 22)
Using the projector at a vertical angle that exceeds 20° may reduce product life or result in malfunction.
JJ Be sure to ask a specialized technician when installing the product to a
ceiling.
If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment
(Optional accessories Æpage 16).
Please call a specialized technician or contact an Authorized Service Center for installation.
12 - ENGLISH
Precautions for Use
zz Do not stack the projectors.
zz Do not block the ventilation ports
(intake and exhaust) of the projector.
zz Avoid heating and cooling air from
the air conditioning system directly
blow to the ventilation ports (intake
and exhaust) of the projector.
zz You can tilt the projector within ±20
degrees horizontally.
Important
Information
JJ Cautions when setting the projectors
+20°
-20°
over 50 cm
(20")
over 50 cm
(20")
over 1 m (40")
over 20 cm
(7.8")
zz Do not place the projector in an enclosed space.
If you need to place the projector in an enclosed space, additional air conditioning and ventilation system
must be equipped. When ventilation is insufficient, remaining heat may trigger the protection circuit of the
projector.
Security
JJ Take safety measures against following incidents.
zz Personal information being leaked via this product.
zz Unauthorized operation of this product by a malicious third party.
zz Interfering or stopping of this product by a malicious third party.
JJ Security instruction (Æpage 57)
zz Make your password as difficult to guess as possible.
zz Change your password periodically.
zz Panasonic or its affiliate company never inquires a password directly to a customer. Do not tell your password
in case you receive such an inquiry.
zz The connecting network must be secured by firewall or others.
zz Set a password and restrict the users who can log in.
Disposal
When disposing of the product, ask your local authority or dealer about the correct methods of disposal.
The lamp contains mercury. When disposing of the used lamp unit, ask your nearest local authorities or dealer
about proper disposal of the unit.
Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
ENGLISH - 13
Precautions for Use
Important
Information
Cautions on use
JJ In order to get the picture quality
zz Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light
from indoor lamps from shining onto the screen.
zz Depending on where the projector is used, heated air from an exhaust port or warm or cold air from an air
conditioner can cause a shimmering effect on screen.
Avoid use in locations where exhaust or streams of air from projector, other devices and air conditioners flow
between the projector and the screen.
zz The lens of projector is affected by the heat from the luminous source. Because of this, the focusing may not
be stable right after the power is turned on. Focusing is stabled after projecting image for 30 minutes and
longer.
JJ Do not touch the surface of the projector lens with your bare hand.
If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected
onto the screen.
JJ LCD Panel
The display unit of this projector comprises three LCD panels. Although an LCD panel is a product of highprecision technology, some of the pixels on the projected image may be missing or constantly lit. Please note that
this is not a malfunction.
Displaying a still image for a longer time may result in an after-image on the LCD panels. If this happens, display
the all white screen in the test pattern for an hour or more.
JJ Optical components
Operating the projector in an environment with high temperature or heavy exposure to dust or tobacco smoke
will reduce the service life of the optical components, such as the LCD panel and polarizing plate, and may
necessitate their replacement within less than one year of use. For details, consult your dealer.
JJ Lamp
The luminous source of the projector is a mercury lamp with high internal pressure.
A high pressure mercury lamp has following characteristics.
zz The brightness of the lamp will decrease by duration of usage.
zz The lamp may burst with sound or shorten life by shock or chipping.
zz The life of the lamp varies greatly depending on individual specificities and usage conditions. In particular,
continuous use over 6 hours and frequent on/off switching of the power greatly deteriorate the lamp and affect
the lamp life.
zz In rare cases, the lamp burst shortly after the projection.
zz The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the
lamp unit consistently. (“When to replace the lamp unit” (Æ page 64))
zz If the lamp bursts, gas contained inside of the lamp is released in a form of smoke.
zz It is recommended to store replacement lamps for contingency.
zz It is recommended to have authorized engineer or your dealer replace the lamp unit.
Pursuant to at the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
14 - ENGLISH
Accessories
Make sure the following accessories are provided with your projector. Numbers in the brackets ( ) show the
number of accessories.
Power cord (x1)
(6103581217)
CD-ROM (x2)
(6103589343)
(6103597300)
Batteries (AAA/R03 type)
(x6)
RGB signal cable (x1)
(6103580425)
Cable holder (x1)
(6103547107)
AC power cord holder
(x1) (6103592442)
(6103592466)
Lens cover (x1)
(6103490106)
String (x1)
(6103504711)
Interactive light pen (x1)
(6451056078)
Interactive pointer (x1)
(6451056085)
Interactive USB cable
(x1) (6451043719)
Remote control unit (x1)
(6451053893)
Important
Information
Precautions for Use
Ferrite core (x1)
(6520032767)
Attention
zz After unpacking the projector, discard the power cord cap and packaging material properly.
zz For lost accessories, consult your dealer.
zz The part numbers of accessories and separately sold components are subject to change without notice.
zz Store small parts in an appropriate manner, and keep them away from young children.
ENGLISH - 15
Precautions for Use
Important
Information
JJ Contents of the supplied CD-ROM No.1
The contents of the supplied CD-ROM are as follow.
Operating Instructions – Projector Operations
Operating Instructions – Network Operations
[: Instructions/List (PDF), : Software]
Multi Projector Monitoring & Control Software 2.6(Windows)
•• This software allows you to monitor and control multiple projectors connected to the LAN.
Operation Manual Multi Projector Monitoring & Control Software 2.6
Logo Transfer Software 2.0(Windows)
•• This software allows you to create original images, such as company logos to be displayed when projection
starts, and transfer them to the projector.
Operation Manual Logo Transfer Software 2.0
List of compatible projector models
•• This is a list of projectors that are compatible with the software marked with the “” symbols above, and their
restrictions.
JJ Contents of the supplied CD-ROM No.2
Operation Manual - Light Pen II
Light Pen II (Windows / Mac OS)
Optional accessories
Options
Ceiling Mount Bracket
Model No.
ET-PKV100H (for high ceilings), ET-PKV100S (for low ceilings)
Projector Mount Base
ET-PKT100B
Replacement Lamp Unit
ET-LAT100
Replacement Filter Unit
ET-RFT100
Interactive Light Pen
ET-PEN100
Interactive Pointer
ET-PNT100
16 - ENGLISH
About Your Projector
(17)
(1)
(10)
(2)
(3)
(11)
(4)
(5)
(12)
(6)
(7)
(13)
(14)
(8)
(15)
(16)
(9)
(9) <VOLUME +/-> Buttons
Adjusts the volume of the speaker. (Æpage 34)
(10) < > Button
Turn the projector on or off. (Æpage 28)
(11) <KEYSTONE> Button
Correct keystone distortion. (Æpage 33)
(12) <INFO.> Button
Operate the information function. (Æpage 33)
(13) <LAMP> Button
Select a lamp mode. (Æpage 34)
(14) <P-TIMER> Button
Operate the P-timer function. (Æpage 34)
(15) <IMAGE> Button
Select the image mode. (Æpage 35)
(16) <MUTE> Button
Mute the sound. (Æpage 35)
(17) Remote control signal emitter
Attention
zz Do not drop the remote control.
zz Avoid contact with liquids.
zz Do not attempt to modify or disassemble the remote
control.
Note
(1) <AUTO SETUP> Button
Execute the setting of Auto setup in the setting
menu. (Æpage 52)
(2) Input Selection Buttons: <COMPUTER 1>,
<COMPUTER 2>, <HDMI>, <VIDEO>,
<S-VIDEO>, <COMPONENT>.
These buttons are used to select the input signal.
(Æpage 32)
(3) ▲▼◄► Buttons, <ENTER> Button
Navigate the MENU display.(Æpage 36)
(4) <SCREEN> Button
Select a screen mode. (Æpage 48 to 50)
(5) <MENU> Button
Open or close the On-Screen Menu. (Æpage 36)
(6) <FREEZE> Button
Pauses the projected image and sound tentatively.
(Æpage 33)
(7) <AV MUTE> Button
Temporarily turn off the image on the screen.
(Æpage 34)
(8) <D.ZOOM +/-> Buttons
zz The remote control can be used within a distance of
about 7 m (22.97 ft) if pointed directly at the remote
control signal receiver. The remote control can control at
angles of up to ± 30 ° vertically and ± 30 ° horizontally,
but the effective control range may be reduced.
zz If there are any obstacles between the remote control
and the remote control signal receiver, the remote control
may not operate correctly.
zz You can operate the projector by reflecting the remote
control signal on the screen. The operating range may
differ due to the loss of light caused by the properties of
the screen.
zz When the remote control signal receiver is lit with a
fluorescent light or other strong light source, the projector
may become inoperative. Set the projector as far from
the luminous source as possible.
Zoom in and out the images. (Æpage 34)
ENGLISH - 17
Preparation
Remote control
About Your Projector
Projector body
(1)
Preparation
(3)
(4) (5)
(6)
(2)
(8)
(7)
(9)
(10)(11)
(12)
(13)
■ Bottom view
(14)
(1) Control panel(Æpage 19)
(2) Lamp cover (Æpage 65)
The lamp unit is located inside.
(11) Focus lever
Adjusts the focus.
(12) Security bar
(3) Remote control signal receiver
(13) AC IN
(4) Interactive Camera
(14) Adjustable feet
Adjusts the projection angle.
(5) Projection lens
(6) Speaker
(7) Air outlet port
Hot air is exhausted from the exhaust vent. Do not
put heat-sensitive objects near this side.
(8) Air intake port / Air filter cover (Æpage 63)
(9) Side terminals (Æpage 20)
(10) Indicators(Æpage 19)
Interactive Function
Note
zz As
for Interactive function, refer to the "Operation Manual
- Light Pen II" in the application CD-ROM.
18 - ENGLISH
WARNING:
zz Keep your hands and other objects away from
the air exhaust port.
zz Keep your hand and face away.
zz Do not insert your finger.
zz Keep heat-sensitive articles away.
Heated air from the air exhaust port can cause burns
or external damage.
About Your Projector
Control panel
(1)
(3)
(2)
(4)
(1) <
> button
Turn the projector on/off.
(2) ▲▼◄► (VOL -/+) buttons
(6)
(5)
(3) <ENTER> button
Execute the selected item.
(4) <MENU> button
Displays the MENU screen. (Æpage 36)
(5) <KEYSTONE> button
Correct the keystone distortion. (Æpage 33)
(6) <INPUT> button
Selects the input signal. (Æpage 32)
Indicators
(1) <ON(G)/STANDBY(R)> indicator
Indicate the power status.
(2) <WARNING> indicator
Indicate the abnormal conditions of the projector.
(3) <LAMP> indicator
Lights yellow when the projection lamp reaches its
end of life.
(1)
(2)
(3)
ENGLISH - 19
Preparation
Navigate the MENU screen.
About Your Projector
Side terminals
(1)
(2)
(3)
(5)
(4)
(6)
(7)
Preparation
(8)
(1) LAN
Connect to a LAN cable for network connection.
(2) HDMI
Connect to HDMI input signals.
(3) COMPUTER IN 1/ COMPONENT IN
Connect to COMPUTER IN 1/ COMPONENT IN
input signals.
(4) COMPUTER IN 2/ MONITOR OUT
Connect to COMPUTER IN 2/ MONITOR OUT
input signals or outputs the analog RGB signals
input the projector.
(5) S-VIDEO IN
Connect to S-VIDEO input signals.
(6) AUDIO OUT (VARIABLE)
Output the audio signals input to the projector.
(7) CONTROL PORT
Connect to a computer via an RS-232C cable.
20 - ENGLISH
(9)
(10) (11)
(8) Security slot
Attach the commercial shackle lock, manufactured
by Kensington, to protect your projector.
Compatible with the Kensington MicroSaver
Security System.
(9) VIDEO IN
Connect to VIDEO input signals.
(10) AUDIO IN
Connect to the audio input signals.
AUDIO IN has right and left (L and R) terminals.
(11) COMPUTER / COMPONENT AUDIO IN
Connect the audio output (stereo) from a computer
or video equipment connected to (2), (3) or (4) to
this jack.
Attention
zz When a LAN cable is directly connected to the projector,
the network connection must be made indoors.
Using Remote control
Using Remote control
Installing and Removing batteries
2222 Install batteries and close the cover
(Insert the – side first.)
zz Remove the batteries in the reverse order of
installation.
Setting Remote control ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each
projector individually using single remote control, if unique ID number is assigned to each projector.
After setting the ID number of the projector, set the same ID number to the remote control.
There are 7 different ID codes (ALL, Code 1~Code 6), the initial ID number is [ALL].
JJ
Setting the ID number
1) W
hile holding down the <MENU> button, press the <IMAGE> button. The number of times you press
the <IMAGE> button corresponds to the desired ID code number.
2) The number of times to press the <IMAGE> button is as follows:
Code 1= Once, Code 2= Twice, Code 3= 3 times, Code 4= 4 times
Code 5= 5 times, Code 6= 6 times
3) The ID code is changed when the <MENU> button is released.
4) T
he ID code is reset to [ALL] (default) by pressing the <MENU> button and <IMAGE> button at the
same time for 5 seconds or more.
Attention
zz If the <IMAGE> button is pressed 7 times or more, the ID code
cannot be changed (the operation is invalid).
zz The status of the ID code is not stored after replacing batteries.
Note
zz For details, please refer to the [Remote control] of the [Setting] menu.
(Æpage 57)
MENU button
IMAGE button
ENGLISH - 21
Preparation
1111 Open the cover
Setting up
Projection method
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector.
JJMounting on the ceiling and
projecting forward
JJSetting on a desk/floor and
projecting from rear
(Using translucent screen)
Getting Started
JJMounting on the ceiling and
projecting from rear
JJSetting on a desk/floor and
projecting forward
(Using translucent screen)
Attention
zz For optimum viewing quality, install the projector in a location where screen exposure to outside light, light from light fixtures
or other light is at a minimum. Also draw the curtains, close blinds and turn off light fixtures.
zz Do not use the projector installed vertically or tilted right or left. Use under such conditions could result in equipment
damage.
+20°
zz The projector must be installed so that its inclination to the horizontal plane is ±20° or less.
zz Installing the projector at an inclination that exceeds 20° may reduce product life or
-20°
result in malfunction.
Parts for ceiling mount (Optional)
You can install the projector on the ceiling by using the optional ceiling mount bracket (ET-PKV100H: for high
ceiling, ET-PKV100S: for low ceiling), and the optional projector mount base ET-PKT100B.
zz Use only the ceiling mount brackets specified for this projector.
zz Refer to the installation manual for the ceiling mount bracket when you install the bracket and the projector.
Attention
zz To ensure projector performance and security, installation of the ceiling mount bracket must be carried by your
dealer or a qualified technician.
22 - ENGLISH
Setting up
Screen size and throw distance
SH
Projected image
SD
Screen
SH
Place the projector referring
to the diagram on the right
and the figures of throwing
distance. You can adjust the
display size.
L
SW
Projection distance (m)
Height of the projection area (m)
SW
Width of the projection area (m)
SD
Diagonal length of the projection area (m)
L
SW
SH
Screen
Attention
zz Before installing, please read “Precautions for Use” (Æ pages 12 to 16).
JJ
Projection distance
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection size
For 16:10 aspect ratio
Screen diagonal (SD)
For 4:3 aspect ratio
For 16:9 aspect ratio
Projection distance
1.52 m(60")
0.64 m(2.09')
0.73 m(2.38')
0.65 m(2.15')
1.78 m(70")
0.75 m(2.46')
0.85 m(2.80')
0.77 m(2.53')
2.03 m(80")
0.86 m(2.82')
0.98 m(3.21')
0.89 m(2.90')
2.29 m(90")
0.97 m(3.19')
1.11 m(3.63')
1.00 m(3.28')
2.54 m(100")
1.08 m(3.56')
------
1.12 m(3.66')
2.79 m(110")
1.2 m(3.97')
------
------
Any other projection distance can be obtained according to the screen dimensions (m) using the following
calculations.
The distance is shown in units of meters. (The calculated distance may contain a certain error.)
If the screen dimensions are written as “SD",
For 16:10 aspect ratio
For 4:3 aspect ratio
For 16:9 aspect ratio
Screen height (SH)
= SD(m) × 0.530
= SD(m) × 0.6
= SD(m) × 0.490
Screen width (SW)
= SD(m) × 0.848
= SD(m) × 0.8
= SD(m) × 0.872
Projection distance (L)
= 0.44157 × SD(m) - 0.036768
= 0.49988 × SD(m) - 0.036768
= 0.45386 × SD(m) - 0.036768
Note
zz Install the projector where the projection distance should be within 63.6cm and 120cm in order to keep the lens
performance.
ENGLISH - 23
Getting Started
L
Setting up
Adjusting front adjustable feet
Projection angle can be adjusted up to 10.0 degrees with the adjustable feet.
Rotate the adjustable feet and tilt the projector to the proper height; to raise the projector, rotate the both feet
clockwise.
To lower the projector or to retract the adjustable feet, rotate the both feet counterclockwise.
(You can adjust the projection angle vertically.)
Getting Started
Attention
Adjustable Feet
Adjustable range
Front adjustable feet: 43.5 mm (1.713")
zz Heated air comes out of the air exhaust port while the lamp is lit. Do not touch the air exhaust port directly when you adjust
the front adjustable feet.
zz If keystone distortion occurs on the projected image, perform “KEYSTONE” from the “Screen” menu. (Æpage 49)
Note
zz Screw up the adjustable feet, and an audible click will be heard as the limit.
24 - ENGLISH
Connections
Before connecting to the projector
zz Read carefully the instruction manual for the device to be connected.
zz Turn off the power switch of the devices before connecting cables.
zz If any connection cable is not supplied with the device, or if no optional cable is available for connection of the
device, prepare a necessary system connection cable to suit the device.
zz Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture.
In this case, a time base corrector (TBC) must be connected.
zz The projector accepts the following signals: VIDEO, S-VIDEO, analogue-RGB (with TTL sync. Level) and
digital signal.
zz Some computer models are not compatible with the projector.
zz When using long cables to connect with each of equipment to the projector, there is a possibility that the image
will not be output correctly unless a compensator is used.
zz For details on what video signals the projector supports, see “List of compatible signals”. (Æpage 73 to 76)
Computer
Audio system
Video deck
(TBC built-in)
Blue ray disk player with HDMI
terminal
Control computer
Attention
zz When connecting with a video deck, be sure to use the one with a built-in time base corrector (TBC) or use a TBC between
the projector and the video deck.
zz If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC between the
projector and the video deck.
Note
zz When using an HDMI cable, check that it is compliant with the HDMI standard. Using a cable that is not compliant with the
HDMI standard may result in problems such as the image cutting out or not appearing.
When connecting the 1080p signal using HDMI, use a cable compliant with 1080p signal.
zz This projector does not support the Viera link (HDMI).
zz For the specifications of the RGB signals that can be applied from the PC, refer to “List of compatible signals”.
(Æpage 73 to 76)
zz See “Network operation” in the instruction manual on the supplied CD-ROM for the details of wired LAN communication
between the projector and the computer.
ENGLISH - 25
Getting Started
Connecting example
asic Operation
Powering ON/OFF
Connecting the power cord
Be sure to insert the attached power cord securely to its base to prevent it from coming off.
JJPower cord holder
AC power cord holder is designed to prevent the AC power cord from coming off the projector.
Please insert the power cord into the power cord holder correctly as Picture (1) shown:
AC Power cord holder
Clamp
Picture (1)
JJAttaching
Attach the AC power cord with the power cord clamp to the projector by following these steps.
Basic Operation
1111 Plug the power cord with the power cord holder to the projector as Picture (2) shown.
2222 Push the clamp at the AC Power cord holder downward to secure it to the projector. It is correctly attached
until you hear the "CLICK" sound. See Picture (3) for correct attachment.
Bottom view
Picture (2)
26 - ENGLISH
Picture (3)
Powering ON/OFF
ON(G)/STANDBY(R) indicator
The <ON(G)/STANDBY(R)> indicator informs you the status of the power. Confirm the status of the <ON(G)/
STANDBY(R)> indicator before operating the projector.
ON(G)/STANDBY(R) indicator
Indicator status
No illumination or flashing
Lit
The power cord is unplugged.
The power cord is plugged.
The projector is in stand-by mode, after the cooling is completed.
Flashing
Lit
Flashing
The temperature inside the projector is abnormally high. And the <WARNING>
indicator also blinks in red (Æpage 61). The projector cannot be turned on until
cooling is completing and the <ON(G)/STANDBY(R)> indicator stops blinking.
Projecting.
The projector is in the Power management mode.
ENGLISH - 27
Basic Operation
The projector cannot be turned on until the normal power-off processing for fan
cooling is completing and the <ON(G)/STANDBY(R)> indicator stops blinking.
RED
GREEN
Status
Powering ON/OFF
Turning On the Projector
(3)
(3)
(3)
(2)
1111 Complete peripheral connections (with a
computer, VCR, etc.) before turning on the
projector.
06
2222 Connect the projector’s AC power cord into an
AC outlet. The <ON(G)/STANDBY(R)> indicator
lights red. Open the lens cover.
Basic Operation
3333 Press the < > button on the control panel or on
the remote control. The <ON(G)/STANDBY(R)>
indicator lights green and the cooling fans start
to operate. The preparation display appears on
the screen and the count down starts.
4444 After the countdown, the input source that was
selected the last time and the lamp power status
icon appear on the screen.
5555 If there is no signal input when start on the
projector, or the current signal is missed while
operating the projector, the Video/Computer
selection window will be displayed on the screen,
please move the pointer to input source desired
by pressing the ▲▼ and the <ENTER> button.
And then follow the input signal guidance window
to correct the signal and connection.
If the projector is locked with a PIN code, PIN
code input dialog box will appear. Enter the PIN
code as instructed on the next page.
Note
zz When the [Direct on] function is set to [On], the projector
will be turned on automatically by connecting the AC
power cord to an AC outlet.
zz When the [Logo select] function is set to [Off], the logo
will not be shown on the screen (Æpage 53).
zz When [Countdown off] or [Off] is selected in the [Display]
function, the preparation display will not be shown on the
screen (Æpage 53).
zz When the [Input search] function is set to [On 2], the
input signal will be searched automatically (Æpage 52).
28 - ENGLISH
The preparation display will disappear
after 30 seconds.
Selected Input Source and Lamp power
Lamp power status
Video/Computer selection
Powering ON/OFF
Enter a PIN code
Press ▲▼ to enter a number. Press ► to fix the
number and move the red frame pointer to the next
box. The number changes to . If you fixed an
incorrect number, use the ◄ button to move the
pointer to the number you want to correct, and then
enter the correct number.
Repeat this step to complete entering a four-digit
number.
After entering the four-digit number, move the pointer
to “Set”. Press the <ENTER> button so that you can
start to operate the projector.
PIN Code Input Dialog Box
After the OK icon disappears,
you can operate the projector.
If you entered an incorrect PIN code, PIN code and
the number () will turn red for a moment. Enter
the correct PIN code all over again.
Note
Basic Operation
zz If the PIN code number is not entered or wrong PIN code
number is entered within three minutes after the PIN
code dialog box appeared, the projector will be turned off
automatically.
zz The “1234” is set as the initial PIN code at the factory.
ENGLISH - 29
Powering ON/OFF
Turning Off the Projector
1111 Press the < > button on the control panel or on
the remote control, and Power off? appears on
the screen.
2222 Press the < > button again to turn off the
projector. The <ON(G)/STANDBY(R)> indicator
starts to blink red, and the cooling fans keep
running. At this time, you can unplug the AC
power cord even if the fans are still running.
3333 When the projector has cooled down enough, the
<ON(G)/STANDBY(R)> indicator stops blinking
and you can turn on the projector.
Note
Basic Operation
zz Do not put the projector in a case before the projector is
cooled enough.
zz While the <ON(G)/STANDBY(R)> indicator is blinking,
the lamp is being cooled down and the projector cannot
be turned on. Wait until the <ON(G)/STANDBY(R)>
indicator stops blinking to turn on the projector again.
zz The projector can be turned on after the <ON(G)/
STANDBY(R)> indicator turns red. The waiting time
to restart will be shortened when the normal power-off
processing for fan cooling is completed, compared with
the time the AC power cord is immediately unplugged
after the power-off.
JJDirect Power Off function
You can disconnect the power cord from the wall
outlet or turn off the breaker even during projection
without pressing the < > button.
Note
zz When using the Direct Power Off function, you can
not restart the projector immediately after the power is
disconnected. The lamp remains high temperature and
needs to be cooled, so it sometimes takes longer time
than usual for the lamp to light up again.
30 - ENGLISH
Power off? disappears after 4 seconds.
Projecting
Check the connections of the peripheral devices and connection of the power cord (Æpage 26) and switch on the
power (Æpage 28) to start the projector. Select the image and adjust the state of the image.
Selecting the image
Select an input signal.
The image selected with the <COMPUTER 1>,
<COMPUTER 2>, <HDMI>, <VIDEO>, <S-VIDEO>,
or <COMPONENT> button is projected (Æpage 32).
Attention
zz Images may not be projected properly depending on the
connected device and DVD, video tape, etc. to be played.
Select a system format that is suitable for the input signal
in [Component] or [RGB] in the [Input] menu (Æpage 39).
zz Check the aspect ratio of the screen and the image and
select the optimum aspect ratio under the [Screen] menu
(Æpage 48).
How to adjust the state of the
image
1111 Adjust the projection angle.
zz For details, see “Adjusting front adjustable feet”.
Basic Operation
(Æpage 24)
2222 Adjust the focus.
Turn [focus lever] to adjust the image.
Focus Lever
Note
zz It is recommended that the images are projected
continuously for at least 30 minutes before the focus is
adjusted.
zz If keystone distortion occurs, see “KEYSTONE”
(Æpage 49).
ENGLISH - 31
Basic operations by using the remote control
COMPUTER 1
Switches to Computer 1(RGB)/
Computer 1(Scart) input.
COMPUTER 2
Switches to Computer 2(RGB)
input.
HDMI
Switches to HDMI input.
VIDEO
Switches to Video input.
S-VIDEO
COMPONENT
Switches to S-video input.
Switches to Computer 1
(Component) input.
Note
zz Each press of the <INPUT> button on the Control Panel
of the main unit switches the settings as shown below.
(Æpage 19)
Computer 1 (RGB)/
Computer 1 (Component)/
Computer 1 (Scart)
Using the Auto setup function
Basic Operation
This function allows you to automatically adjust Input
search and Auto PC adj. during signal input from a
computer.
button
*
Computer 2
(RGB)
HDMI
S-video
Video
t depends on the item you selected in the
* I[Computer
1] submenu of the [Input] menu.
Using the SCREEN button
Press the <AUTO SETUP> button on the
remote control.
This function allows you to select screen mode or
change the screen size.
button
Note
zz For details, see “Setting” of Main menu. (Æpage 52)
Press the <SCREEN> button on the
remote control.
Switching the input signal
You can switch the input signals to project.
buttons
Press (<COMPUTER 1>,<COMPUTER
2>, <HDMI>, <VIDEO>, <S-VIDEO>, or
<COMPONENT>) buttons on the remote
control.
32 - ENGLISH
Note
zz For details, see “Screen” of Main menu.
(Æpage 48 to 50)
Basic operations by using the remote control
Using the KEYSTONE button
This function allows you to correct keystone distortion.
Using the INFO. button
This function allows you to display the information
menu.
button
button
Press the <KEYSTONE> button on the remote control
or on the control panel. The Keystone dialog box
appears. Press ▲▼ to correct keystone distortion.
The keystone adjustment can be stored (Æpage 49).
Press <INFO.> button on the remote
control.
Note
Screen image
Reduce the
upper width
with press
▲.
Reduce the
lower width
with press
▼.
Note
zz The white arrows indicate that there is no correction.
zz A red arrow indicates the direction of correction.
zz An arrow disappears at the maximum correction.
zz If you press the <KEYSTONE> button on the remote
control or on the control panel once more while the
keystone dialog box is being displayed, the keystone
adjustment will be canceled (Æpage 49).
zz The adjustable range is limited depending on the input
signal.
Using the FREEZE function
You can freeze the projected image and stop the
sound temporarily, regardless of the playing condition
of the connected device.
button
Press the <FREEZE> button on the remote control to
freeze the picture on the screen, meanwhile, volume
is muted. To cancel the Freeze function, press the
<FREEZE> button again or press any other button.
Fig.1 will appear on the screen while the Freeze
function is working.
Fig.1
Note
zz When no signal inputs,
mark will appear.
ENGLISH - 33
Basic Operation
Operation
zz For details, see “Input Source Information Display” in
“Information” under Main menu (Æpage 60).
Basic operations by using the remote control
Using the AV MUTE function
This function allows you to select the lamp mode for
changing the brightness on the screen.
button
Press the <AV MUTE> button on the remote control
to black out the image. To restore to normal, press the
<AV MUTE> button again or press any button.
zz When the Logo is not set, the screen changes each time
you press the <AV MUTE> button as follows.
black out
projected image
zzThe projected Logo (the logo can be set according
to users’ favorite) is transferred from computer to
the projector by “Logo Transfer Software” on the
supplied CD-ROM and is set as [User] in the Logo
selection(Æpage 53), the screen changes each
time you press the <AV MUTE> button as follows.
black out
Using the LAMP button
Logo
button
Press <LAMP> button on the remote
control.
Note
zz For details, see “Lamp Power” of "Setting" under Main
menu. (Æpage 56)
Using the D.ZOOM buttons
This function allows you to enter the Digital zoom +/–
mode.
projected image
Basic Operation
buttons
Note
zz When use the <MUTE> button to release the [AV mute]
function, the mute function can not be operated at the
same time.
Press <D.ZOOM +/-> buttons on the
remote control.
Note
zz For details, see "Screen" of Main menu.(Æpage 49)
Using the P-TIMER button
Press the <P-TIMER> button on the remote control to
operate the Count up/Count down function.
button
Press <P-TIMER> button on the remote
control.
Controlling the volume of the
speaker
You can control the volume of the projector’s speaker
or audio output.
buttons
Note
zz To stop the count time, press the <P-TIMER> button.
To cancel the [P-timer] function, press and hold the
<P-TIMER> button.(Æpage 55)
Press the <VOLUME +/–> buttons on the control
panel or on the remote control to adjust the volume.
The volume dialog box appears on the screen for a
few seconds.
Note
zz For details, see “Volume” of "Sound" under Main menu.
(Æpage 51)
34 - ENGLISH
Basic operations by using the remote control
Using the IMAGE button
This function allows you to select a desired image
mode of the screen.
button
Press <IMAGE> button on the remote control to select
the desired image mode among [Dynamic], [Standard],
[Real], [Cinema], [Blackboard (Green)], [Colorboard],
[Image 1], [Image 2], [Image 3] and [Image 4].
Note
zz For details, see “Image select” of Main menu.
(Æpage 44)
Using the MUTE button
Basic Operation
Press this button on the remote control to select On to
temporarily turn off the sound.
button
Press <MUTE> button on the remote
control.
Note
zz To turn the sound back on, press this button again to
select [Off] or press the <VOLUME +/–> buttons.
(Æpage 51)
ENGLISH - 35
Menu Navigation
Navigating through the menu
JJOperating procedure
1111 Press the <MENU> button.
The Main Menu screen appears.
2222 Press ▲▼ to select the Main Menu
item.
Select the desired item from the 9 items: [Input],
[PC adjust], [Image select], [Image adjust],
[Screen], [Sound], [Setting], [Information] and
[Network]. The selected item is highlighted with an
orange cursor and the submenu of the selected
item appears on the right.
3333 Press ► or the <ENTER> button.
The submenu appears so that you can select the
sub-menu item.
Settings
4444 Press ▲▼ to select the desired submenu item.
5555 Press the <ENTER> button or press ►
to enter the desired item.
6666 Press ▲▼ ◄► to set or adjust the
parameter values.
7777 Press ◄ to return the previous menu.
Press the <MENU> button to exit the
menu display.
36 - ENGLISH
Note
zz Some items may not be adjusted or used for certain
signal formats input to the projector. The MENU items
that cannot be adjusted or used are shown in gray
characters, and they cannot be selected.
zz Some items can be adjusted even if signals are not input.
zz See page 37 and 38 for details on the items of sub-menu.
Menu Navigation
Sub menu
The main menu consists of the following 9 menu
items.
When a main menu item is selected, the screen
changes to a submenu selection screen.
The sub-menu screen of the selected main menu
appears, and you can set and adjust the various items
in the submenu.
JJInput [
Input
PC adjust
Image select
Image adjust
Setting
Information
Network
Factory
default
RGB
RGB
-
Sub-menu item
Computer 1
Computer 2
HDMI
Video
S-video
JJPC adjust [
Screen
Sound
]
Page
39
39
39
39
39
]
Factory
default
-
Sub-menu item
Auto PC adj.
Fine sync.
Total dots
Horizontal
Vertical
Current mode
Clamp
Display area H
Display area V
Reset
Mode free
Store
Page
41
42
42
42
42
43
43
43
43
43
43
43
Note
zz This function will be available when the input source
come from computer.
JJImage select [
Sub-menu item
Dynamic
Standard
Real
Cinema
Blackboard(Green)
Colorboard
Image 1-4
]
Factory
default
Red
-
Page
44
44
44
44
44
44
44
ENGLISH - 37
Settings
Main menu
Menu Navigation
Image adjust [
JJSetting [
]
Sub-menu item
Contrast
Brightness
Color*1
Tint*1
Color temp.
Red
Green
Blue
Sharpness
Gamma
Noise reduction*1
Progressive*1
Reset
Store
Factory default
32
32
32
32
Mid
32
32
32
8
8
L1
L1
-
Page
45
45
45
45
45
46
46
46
46
46
46
47
47
47
***** When input video signal to the projector, these
functions will be available.
JJScreen [
]
Settings
Sub-menu item
Normal
Full
Wide (16:9)
Zoom
True*1
Natural wide*2
Custom
Custom adj.
Digital zoom + *1
Digital zoom - *1
Keystone
Ceiling
Rear
Screen aspect
Reset
Factory default
Store
Off
Off
Default(16:10)
-
Page
48
48
48
48
48
48
48
49
49
49
49
50
50
50
50
***** When input computer signal to the projector, these
functions will be available.
***** When input video signal to the projector, this function
will be available.
JJSound [
Sub-menu item
Volume
Mute
38 - ENGLISH
]
Factory default
32
Off
Page
51
51
]
Sub-menu item
Language
Menu position
Auto setup
Background
Display
Logo
HDMI setup
Terminal
Power management
Direct on
Standby mode
P-timer
Closed caption
Lamp power
Remote control
Security
Fan
Fan control
Video delay control
Lamp runtime
Filter counter
Warning log
Factory default
Factory default
English
Center
Blue
On
Computer 2
Shut down
Off
Eco
Count up
Off
Normal
ALL
L2
Off
Off
-
JJInformation [
]
Sub-menu item
Input
System
H-sync freq.
V-sync freq.
Screen
Language
Lamp power
Lamp runtime
Power management
Key lock
PIN code lock
Remote control
Serial number
JJNetwork [
Page
52
52
52
53
53
53
54
54
54
55
55
55
56
56
56
57
57
58
58
58
58
59
59
Factory default
-
]
Page
60
60
60
60
60
60
60
60
60
60
60
60
60
Refer to “Operating Instructions - Network operations”.
Input menu
Select [Input] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
Mode 1
he preset system is manually adjusted in
T
the PC adjust Menu. The adjusted data can
be stored in Mode 1-10.
C Systems provided in this projector is
SVGA 1 P
chosen. The projector chooses a proper
system provided in the projector and
displays it.
* Mode 1 and SVGA 1 are examples.
Computer 1: RGB/Component
/RGB (Scart)
1111 Press ▲▼ to select [Computer 1].
2222 Press ► to access the submenu.
3333 Press ▲▼ to select RGB, Component
or RGB(Scart).
4444 Press the <ENTER> button.
1111 Press ▲▼ to select [System].
2222 Press ► or the <ENTER> button to
access the submenu.
3333 Press ▲▼ to select the desired system.
HDMI
Press ▲▼to select [HDMI] and then press
the <ENTER> button.
zz When [Computer 1] is selected, [Component] or
Computer 2: RGB
Press ▲▼ to select [Computer 2 (RGB)]
and then press the <ENTER> button.
JJComputer System Selection
This projector automatically tunes to various types
of computers with its Multi-scan system and Auto
PC Adjustment. If a computer is selected as a signal
source, this projector automatically detects the signal
format and tunes to project a proper image without
any additional settings. (Signal formats provided in
this projector are shown on pages 73-76.)
AUTO
----
W
hen the projector can not recognize
the connected signal conforming to the
provided PC Systems, Auto is displayed
on the System Menu box and the Auto
PC adjustment function works to display
proper images. If the image is not projected
properly, a manual adjustment is required.
here is no signal input from the computer.
T
Check the connection between your
computer and the projector.
Video
Press ▲▼ to select [Video] and then
press the <ENTER> button.
S-video
Press ▲▼ to select [S-video] and then
press the <ENTER> button.
JJVideo System Selection
Video or S-video
Auto
The projector automatically detects an incoming video
system, and adjusts itself to optimize its performance.
When Video System is [PAL-M] or [PAL-N], select the
system manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
If the projector cannot reproduce proper video image,
select a specific broadcast signal format from among
[PAL], [SECAM], [NTSC], [NTSC 4.43], [PAL-M] and
[PAL-N].
ENGLISH - 39
Settings
[RGB(Scart)] can be available.
Input menu
Component
Auto
The projector automatically detects an incoming video
signal, and adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image,
select a specific component video signal format
among [480i], [576i], [480p], [576p], [720p], [1035i]
and [1080i].
1111 Press ▲▼ to select [System].
2222 Press ► or the <ENTER> button to
access the submenu.
3333 Press ▲▼ to select the desired system.
Note
zz When the [Input Search] function is set to [On 1] or
[On 2] in the [Auto setup] function, the input signal
will be searched automatically.
zz The AV System Menu cannot be selected when
selecting [RGB (Scart)].
Settings
40 - ENGLISH
AUTO PC adjust
AUTO PC adjust
Select [PC adjust] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
Auto PC adj.
Auto PC adjustment function is provided to
automatically adjust Fine sync, Total dots, Horizontal
and Vertical positions to conform to your computer.
Press ▲▼ to select [Auto PC adj.] and
then press the <ENTER> button.
zz [Please wait...] appears while the Auto PC
adjustment is in process.
To store adjustment parameters
Settings
The adjusted parameters from the Auto PC adjustment
can be stored in the projector. Once the parameters
are stored, the setting can be done just by selecting a
Mode (1–10) in the PC System Menu (see page 39).
See also [Store] on page 43.
Attention
zz [Fine sync], [Total dots], [Horizontal] and [Vertical]
position of some computers cannot be fully adjusted
with the Auto PC adjustment function. When the
image is not provided properly with this operation,
manual adjustments are required (Æpages 42-43).
zz The Auto PC adjustment cannot be operated when
[480i], [576i], [480p], [576p], [720p], [1035i] or [1080i]
is selected in the PC System Menu (Æpage 39), or
when the signal is coming from the HDMI terminal.
ENGLISH - 41
Manual
PC adjust
Manual PC adjust
Select [PC adjust] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
Horizontal
1111 Press ▲▼ to select [Horizontal].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the horizontal
picture position.
JJFor horizontal (right and left)
adjustment
Operation
Some computers employ special signal formats
which may not be tuned by Multi-scan system of this
projector. Manual PC adjustment enables you to
precisely adjust several parameters to match those
signal formats. The projector has 10 independent
memory areas to store those parameters manually
adjusted. It allows you to recall the setting for a
specific computer.
Adjustment
Press ◄.
The picture
position
moves to the
right.
Press ►.
The picture
position
moves to the
left.
Vertical
Fine sync
Settings
1111 Press ▲▼ to select [Fine sync].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the value.
zz The value can be adjusted from 0 to 31.
Total dots
1111 Press ▲▼ to select [Total dots].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the value.
42 - ENGLISH
1111 Press ▲▼ to select [Vertical].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the vertical picture
position.
JJFor vertical (up and down)
adjustment
Operation
Adjustment
Press ►.
The picture
position
moves up.
Press ◄.
The picture
position
moves down.
Manual PC adjust
Current mode
1111 Press ▲▼ to select [Current mode].
2222 Press ► or the <ENTER> button to
enter the next submenu to show
H-sync freq. and V-sync freq. of the
connected computer.
Clamp
1111 Press ▲▼ to select [Clamp].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the clamp level.
zz When the image has dark bars, try this
Reset
To reset the adjusted data, all adjustments will return
to their previous figures.
1111 Press ▲▼ to select [Reset].
2222 Press the <ENTER> button.
zz A confirmation box appears and then select [Yes].
Mode free
1111 Press ▲▼ to select [Mode free].
2222 Press ► or the <ENTER> button to
enter the next submenu.
zz Move the highlight to the mode that you want to
clear and then press the <ENTER> button.
adjustment.
1111 Press ▲▼ to select [Display area H].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the horizontal area
displayed by this projector.
1111 Press ▲▼ to select [Store].
2222 Press ► or the <ENTER> button to
enter the next submenu.
zz Move the highlight to one of the Modes 1 to 10
in which you want to store, and then press the
<ENTER> button.
Settings
Display area H
Store
Display area V
1111 Press ▲▼ to select [Display area V].
2222 Press the <ENTER> button to display
the dialog box.
3333 Press ◄► to adjust the vertical area
displayed by this projector.
ENGLISH - 43
Image select
Select [Image select] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
Blackboard(Green)
For the image projected on a blackboard.
Press ▲▼ to select [Blackboard(Green)]
and then press the <ENTER> button.
zz This mode helps enhance the image projected
on a blackboard. This is mainly effective on a
green colored board, not truly effective on a
black colored board.
Colorboard
For the image projected on a colorboard.
Dynamic
For viewing pictures in a bright room.
Press ▲▼ to select [Dynamic] and then
press the <ENTER> button.
Standard
Normal picture mode preset on the projector.
Press ▲▼ to select [Standard] and then
press the <ENTER> button.
Settings
Real
Picture mode with improved halftone for graphics.
Press ▲▼ to select [Real] and then press
the <ENTER> button.
Cinema
Picture mode adjusted with fine tone.
Press ▲▼ to select [Cinema] and then
press the <ENTER> button.
44 - ENGLISH
1111 Press ▲▼ to select [Colorboard].
2222 Press ► or the <ENTER> button to
display the submenu.
zz At the time of simple projection on the colored
wall, you can get the close color image to the
color image projected on a white screen by
selecting the similar color to the wall color from
the preset four colors.
Image 1-4
For viewing with the user preset image mode in the
Image adjust Menu.
Press ▲▼ to select [Image 1-4] and then
press the <ENTER> button.
Image adjust
Image adjust
Select [Image adjust] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Control panel
Remote control
Color
1111 Press ▲▼ to select [Color].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
increase the
Maximum
intensity of the color value 63
Press ◄.
decrease the
Minimum
intensity of the color value 0
Note
zz When input video signal to the projector, [Color] will be
available.
Contrast
Operation
Adjustment
Adjustment
range
Press ►.
increase the contrast
Maximum
value 63
Press ◄.
decrease the
contrast
Minimum
value 0
Brightness
1111 Press ▲▼ to select [Brightness].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
increase the
brightness
Maximum
value 63
Press ◄.
decrease the
brightness
Minimum
value 0
Tint
1111 Press ▲▼ to select [Tint].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the tint value to
get a proper color balance.
zz Adjustments can be made between 0 and 63.
Note
zz When you select [NTSC] or [NTSC4.43] in System menu
under Video input signal, [Tint] will be available.
Settings
1111 Press ▲▼ to select [Contrast].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Color temp.
1111 Press ▲▼ to select [Color temp.].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to select the desired Color
temp. level.
zz You can select the desired [Color temp.] from
[XLow], [Low], [Mid] or [High].
Note
zz [Color temp.] level displays [Blackbord] or [Colorboard]
when the [Blackboard(Green)] or [Colorboard] is selected
in the [Image select] menu.
ENGLISH - 45
Image adjust
Red
Sharpness
1111 Press ▲▼ to select [Red].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
deepen red tone
Maximum
value 63
Press ◄.
lighten red tone
Minimum
value 0
1111 Press ▲▼ to select [Sharpness].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
increase the
Maximum
sharpness of the
value 15
image
Press ◄.
decrease the
Minimum
sharpness of the
value 0
image
Green
1111 Press ▲▼ to select [Green].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
deepen green
tone
Maximum
value 63
Press ◄.
lighten green
tone
Minimum
value 0
Settings
Blue
1111 Press ▲▼ to select [Blue].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the setting value.
Operation
Adjustment
Adjustment
range
Press ►.
deepen blue tone
Maximum
value 63
Press ◄.
lighten blue tone
Minimum
value 0
Gamma
1111 Press ▲▼ to select [Gamma].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to adjust the gamma value
to obtain a better balance of contrast.
zz Adjustments can be made between 0 and 15.
Noise reduction
1111 Press ▲▼ to select [Noise reduction].
2222 Press the <ENTER> button to display
the adjustment dialog box.
3333 Press ◄► to select the desired item.
Off
Disabled
L1
Lower reduction
L2
Higher reduction
zz Noise interference on the screen can be
reduced. Select one of the above options to get
smoother images.
zz [Noise reduction] cannot be selected when
[480p], [576p], [720p], [1035i], [1080i] or [1080p]
is selected.
Note
zz When input video signal to the projector, [Noise
reduction] will become available.
46 - ENGLISH
Image adjust
Progressive
1111 Press ▲▼ to select [Progressive].
2222 Press the <ENTER> button to display
the dialog box.
3333 Press ◄► to select the desired item.
zz An interlaced video signal can be displayed in
progressive mode. Select one of the following
options.
zz [Progressive] cannot be selected when [480p],
[576p], [720p], [1035i], [1080i] or [1080p] is
selected.
Off
Disabled
L1
For an active picture
L2
For a still picture
Film
For watching a film
Note
zz When input video signal to the projector, [Progressive]
will become available.
Reset
To reset the adjusted data, all adjustments will return
to their previous figures.
1111 Press ▲▼ to select [Reset].
2222 Press the <ENTER> button.
Settings
zz A confirmation box appears and then select [Yes].
Store
1111 Press ▲▼ to select [Store].
2222 Press ► or the <ENTER> button.
3333 Press ▲▼ to select one from Image 1
to 4 and press the <ENTER> button.
zz A confirmation box appears and then select [Yes].
ENGLISH - 47
Screen
Screen
Select [Screen] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
True
Provide the image in its original size. When the
original image size is larger than the panel size (1280
x 800), the projector enters to the panning mode
automatically.
1111 Press ▲▼ to select [True] and then
press the <ENTER> button.
2222 Press ▲▼◄► to pan the image.
zz When adjusted, the arrows will turn red. When
reached to the correction limits, the arrows will
disappear.
Note
Normal
Provide the image to fit the screen size while
maintaining the aspect ratio of the input signal.
Press ▲▼ to select [Normal] and then
press the <ENTER> button.
Full
Provide the full screen image.
Press ▲▼ to select [Full] and then press
the <ENTER> button.
zz When input computer signal to the projector, [True] will
be available.
zz [True] is disabled and cannot be displayed when [480i],
[576i], [480p], [576p], [720p], [1035i] or [1080i] is selected
in the PC System Menu.
zz When [True] is selected in the Screen menu, [Digital
zoom +/-] can not be selected.
Natural wide
Modify the 4:3 aspect ratio image to fit the screen size
by stretching the image to make it look natural.
Press ▲▼ to select [Natural wide] and
then press the <ENTER> button.
Note
Settings
Wide(16:9)
zz When input video signal to the projector, [Natural wide]
will be available.
Provide the image at the 16:9 wide screen ratio.
Press ▲▼ to select [Wide(16:9)] and then
press the <ENTER> button.
Custom
Provide the last stored aspect screen image.
Zoom
Scale the image proportionally to fit the entire screen.
Either side of image may go over the screen.
Press ▲▼ to select [Zoom] and then
press the <ENTER> button.
48 - ENGLISH
Press ▲▼ to select [Custom] and press
the <ENTER> button.
Screen
Adjust the screen scale and position manually with
this function.
1111 Press ▲▼ to select [Custom adj.].
2222 Press ► or the <ENTER> button to
enter the next submenu.
3333 Press ▲▼ to choose the item you
want to adjust.
zz You can choose one from the items as below:
Scale H/V
Adjust the Horizontal/Vertical screen
scale.
H&V
When set to [On], the aspect ratio is
fixed.
Position H/V
Adjust the Horizontal/Vertical screen
position.
Common
Save the adjusted scale or position
to all the inputs.
Reset
Reset the all adjusted values.
Digital zoom +
Zoom in the images.
1111 Press ▲▼ to select [Digital zoom +]
and then press the <ENTER> button.
zz The On-Screen Menu disappears and
[D. zoom +] appears.
2222 Press the <ENTER> button to zoom in
the image size and press ▲▼ ◄► to
move the image to the top/bottom/left/
right of the screen.
To exit the Digital zoom +/– mode, press any button
except the <D.ZOOM +/–>, <ENTER> and ▲▼◄►
buttons.
To return to the previous screen size, select a screen
size from the Screen Size Adjustment Menu or select
an input source from the Input Source Selection Menu
(Æpage 37) again, or adjust the screen size with the
<D.ZOOM +/–> buttons.
Note
zz When input computer signal to the projector, [Digital
zoom +/-] will be available.
zz [Digital zoom +/-] cannot be selected when [True] is
selected in the Screen aspect.
zz [Digital zoom +/–] are disabled and cannot be displayed
when [480i], [576i], [480p], [576p], [720p], [1035i] or
[1080i] is selected in the PC System Menu (Æpage 40).
mark
zz When [Digital zoom +/–] functions are disabled,
will appear.
Keystone
This function is used to adjust keystone distortion of
the projected image.
1111 Press ▲▼ to select [Keystone].
2222 Press ► or the <ENTER> button.
3333 Press ▲▼ to choose the item you
want to adjust.
Keystone
To correct keystone distortion
Store
To store or reset the keystone
correction
The following items are the
submenus of [Store].
zz The Panning function can work only when the
image is larger than the screen size. A projected
image can be also expanded by pressing the
<D.ZOOM +> or the <ENTER> button.
Digital zoom -
Store
Keep the keystone correction
even when the AC power cord is
unplugged or turning off the projector.
Reset
Release the keystone correction
when the AC power cord is
unplugged.
Zoom out the images.
1111 Press ▲▼ to select [Digital zoom -]
and then press the <ENTER> button.
zz The On-Screen Menu disappears and
[D. zoom - ] appears.
2222 Press the <ENTER> button to zoom
out image size.
zz The projected image can be also compressed
by pressing the <D.ZOOM –> or the <ENTER>
button.
ENGLISH - 49
Settings
Custom adj.
Screen
Ceiling
Reset
This function is used to project the image from a
ceiling-mounted projector.
1111 Press ▲▼ to select [Ceiling] and then
press the <ENTER> button.
2222 Press ▲▼ to change the image.
zz When this function is set to [On], the picture will
be top/bottom and left/right reversed.
Rear
This function is used to project the image from rear of
the screen.
1111 Press ▲▼ to select [Rear] and then
press the <ENTER> button.
2222 Press ▲▼ to change the image.
zz When this function is set to [On], the picture will
be left/right reversed.
Screen aspect
This function is used to project the image to a 4:3 or
16:9 projection screen.
Settings
1111 Press ▲▼ to select [Screen aspect]
and then press the <ENTER> button.
2222 Press ▲▼ to choose one from the
items as below.
Default(16:10)
16:10 is the aspect of the LCD
panel.
16:9
Set to a 16:9 projection screen.
4:3
Set to a 4:3 projection screen.
Attention
zz When the [4:3] function is selected, [Natural wide] is not
available in the AV screen.
zz When the [16:9] function is selected, [Wide (16:9)] is not
available in the screen.
zz [Natural wide] will grayout when [720p], [1035i], [1080i] or
[1080p] is selected in the AV System Menu.
50 - ENGLISH
To reset the adjusted data, all adjustments will return
to their previous figures.
Press ▲▼ to select [Reset] and then
press the <ENTER> button.
zz A confirmation box appears and then select
[Yes].
Sound
Sound
Select [Sound] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
Volume
1111 Press ▲▼ to select [Volume] and then
Press the <ENTER> button.
2222 Press ◄► to adjust the volume.
Operation
Adjustment
Adjustment
range
Press ►.
turn up the
volume
Maximum
value 63
Press ◄.
turn down the
volume
Minimum
value 0
Settings
zz You can also press <VOLUME +/-> buttons on
the remote control or control panel to adjust the
volume.
Mute
1111 Press ▲▼ to select [Mute] and then
Press the <ENTER> button.
2222 Press the <ENTER> button to switch
the mute function On/Off.
zz Press the <MUTE> button on the remote
control to temporarily turn off the sound. To turn
the sound back on, press the <MUTE> button
again or press the <VOLUME +/–> buttons.
ENGLISH - 51
Setting
Setting
Select [Setting] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
Menu position
This function is used to change the position of the OnScreen Menu.
1111 Press ▲▼ to select [Menu position].
2222 Press the <ENTER> button to change
the position.
zz The Menu position changes each time you
press <ENTER> button as follows:
the center → the bottom left → the bottom right → the
top left → the top right → the center......
Language
1111 Press ▲▼ to select [Language].
2222 Press ► or the <ENTER> button.
3333 Press ▲▼ to select the desired
language.
Auto setup
1111 Press ▲▼ to select [Auto setup].
2222 Press ► or the <ENTER> button.
3333 Press ▲▼ to select these functions as
follows:
JJInput search
his function detects the input signal automatically.
T
When a signal is found, the search will stop.
Off
Input search will not work
On 1
Input search works*1
On 2
Input search works*2
Settings
***** ● When pressing the <AUTO SETUP> button on the
remote control.
>
***** ● When turning on the projector by pressing the <
button on the remote control or control panel.
● When pressing the <AUTO SETUP> button on the
remote control.
● When the current input signal is cut off.*
* I f the AV mute or Freeze function is active, cancel
it to activate the Input search. It is also unavailable
when On-Screen menu is displayed.
JJAuto PC adj.
zzThe language used in the On-Screen Menu is
available in English, German, French, Italian,
Spanish, Portuguese, Dutch, Swedish, Finnish,
Norwegian, Danish, Polish, Hungarian, Romanian,
Czech, Russian, Turkish, Arabic, Kazak,
Vietnamese, Chinese, Korean, Japanese and Thai.
On
Enables Auto PC adjustment *1
Off
Disables Auto PC adjustment
***** When pressing the <AUTO SETUP> button on
the remote control.
Note
zz [Input search] and [Auto PC adj.] cannot be set [Off] at
the same time.
52 - ENGLISH
Setting
Select the background screen for when no input signal
is detected.
1111 Press ▲▼ to select [Background].
2222 Press the <ENTER> button.
3333 Press ▲▼ to switch between each
option as below.
Blue
Blue colored background.
User
The logo transferred by "Logo
Transfer Software *1" is projected.
Black
Black colored background.
***** "Logo Transfer Software" is included on the
supplied CD-ROM.
Display
This function decides whether to display On-Screen
Displays.
1111 Press ▲▼ to select [Display].
2222 Press the <ENTER> button.
3333 Press ▲▼ to switch between each
option as below.
On
Show all the On-Screen
displays *1
Countdown Show the input image instead
off
of the countdown when turning
on the projector *2
Off
Hide the On-Screen Displays *3
***** Use this function when you want to project
images after the lamp becomes bright enough.
The factory default setting is in this option.
***** Use this function when you want to project the
image as early as possible even when the lamp
is not bright enough.
***** Hide the On-Screen Displays except;
● On-Screen Menu.
● [Power off?]
● [P-timer] display.
● No signal for [Power management]
● [Please wait ...]
● Arrows for the [True] function and the [Digital
Zoom +/-] function in the Screen Menu.
Logo
This function allows you to customize the screen logo
with [Logo select], [Logo PIN code lock] and [Logo
PIN code change] functions.
1111 Press ▲▼ to select [Logo].
2222 Press ► or the <ENTER> button.
3333 Press ▲▼ to choose the desired item.
JJLogo select
This function decides on the starting-up display from
among following options.
Off
Default
User
Show the countdown display only.
Show the factory-set logo.
The logo transferred by "Logo
Transfer Software *1 " is projected.
***** "Logo Transfer Software" is included on the
supplied CD-ROM.
JJLogo PIN code lock
This function prevents an unauthorized person from
changing the screen logo.
Off
The screen logo can be changed freely
from the Logo Menu.
On
The screen logo cannot be changed
without a Logo PIN code.
Note
zz If you want to change the Logo PIN code lock setting,
press the <ENTER> button and the Logo PIN code
dialog box appears. Enter a Logo PIN code by following
the steps below. The initial Logo PIN code is set to “4321”
at the factory.
ENGLISH - 53
Settings
Background
Setting
JJLogo PIN code change
Logo PIN code can be changed to your desired fourdigit number.
1111 Press ▲▼ to select [Logo PIN code
change].
2222 Press the <ENTER> button.
zz Current logo PIN code dialog box appears.
3333 Press ▲▼ to enter the current code.
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on
the back of the projector is switchable for computer 2
input or monitor output.
1111 Press ▲▼ to select [Terminal] and
then press the <ENTER> button.
2222 Press ▲▼ to switch the item.
zz The New Logo PIN code input dialog box
appears. Set a new Logo PIN code, a
confirmation box appears, choose [Yes] to set
the new Logo PIN code.
Attention
zz Be sure to note the new Logo PIN code and keep it on
hand. If you lost the number, you could no longer change
the Logo PIN code setting.
HDMI setup
This function is only used for HDMI input source.
1111 Press ▲▼ to select [HDMI setup].
2222 Press ► or the <ENTER> button.
zz The names for the output setting of Digital R/G/
B vary from equipment to equipment.
JJImage
Normal
When the output of Digital R/G/B
equipment is set to Standard.
Settings
Enhanced When the output of Digital R/G/B
equipment is set to Enhanced.
JJSound
HDMI
Computer
Attention
When Digital input source is input,
Sound is set to HDMI.
Computer 2
Computer input
Monitor out
Monitor out
Note
zz Terminal function is not available when selecting
[Computer 2] to the input source. Change the input
source to the others (HDMI or Computer 1 or Video) so
that the Terminal function will be available.
Power management
For reducing power consumption as well as
maintaining the lamp life, the Power management
function turns off the projection lamp when the
projector is not operated for a certain period.
1111 Press ▲▼ to select [Power
management].
2222 Press ► or the <ENTER> button to
access the submenu.
JJMode
1111 Press ▲▼ and then press the
<ENTER> button to select one mode
among the items as below.
Off
[Power management] function is off.
Ready
When the lamp has been fully cooled
down, the <ON(G)/STANDBY(R)>
indicator changes to green blinking.
In this condition, the projection lamp
will be turned on if the input signal
is reconnected or any button on the
control panel or remote control is
pressed.
Shut
down
When the lamp has been fully cooled
down, the power will be turned off.
When DVI input source is changed
to HDMI input source, Sound is set
to Computer.
zz For details, refer to the operating instructions of your
Digital R/G/B equipment.
JJTimer
1111 Press ▲▼ to select [Timer] and then
press the <ENTER> button.
2222 Press ▲▼ to set the Timer(1~30min).
54 - ENGLISH
Setting
P-timer
1111 Press ▲▼ to select [Direct on] and
then press the <ENTER> button.
2222 Press ▲▼ to switch between On and
Off.
zz When this function is set to [On], the projector
will be automatically turned on just by
connecting the AC power cord to a wall outlet.
zz Be sure to turn off the projector properly. If the
projector is turned off in the incorrect sequence,
the [Direct on] function does not work properly.
This function allows you to change the setting of the
P-timer and execute it.
1111 Press ▲▼ to select [P-timer].
2222 Press ► or <ENTER> button to access
the submenu.
JJMode
1111 Press ▲▼ button to select one mode
among the items as below.
The P-timer display 000:00
appears on the screen and the
count up starts (000:00-180:00).
Count up
Standby mode
This function can set the electric power when the
projector is standing by.
1111 Press ▲▼ to select [Standby mode]
and then press the <ENTER> button.
2222 Press ▲▼ to switch between the items
as below.
Eco
Network
Note
Restricts some functions in
standby mode to reduce power
consumption.
Does not restrict functionality
even in standby mode.
zz When selecting [Network], the cooling fans may be
running depending on the temperature inside the
projector even if the projector is turned off.
zz Refer to "Operating Instructions - Network Operations".
zz If Standby mode is set to [Eco], you cannot use network
functions when the projector is standing by. Also, you
cannot use some RS-232C protocol commands.
zz If set to [Network], you can use network functions when
the projector is standing by.
The time set in the Timer setting
Count down appears on the screen and the
countdown starts.
JJTimer
1111 Press ▲▼ to select [Timer] and then
press the <ENTER> button.
2222 Press▲▼ to set the [Timer](1-180 Min).
zz Timer is available in [Count down] only. Factory
default value is 10 Min.
JJExecute
1111 Press ▲▼ to select one among the
items as below and then press the
<ENTER> button.
Start
It executes the count up or count
down function.*1
Reset
Reset the P-timer values.*2
Exit
To exit the P-timer operation.
***** Press the <ENTER> button at Start and the
indication changes into Stop. To stop Count up or
Count down, press the <ENTER> button at Stop
on the screen menu, then the indication changes
into Restart. Press the <ENTER> button at
Restart to resume Count up or Count down.
***** Press the <ENTER> button at Reset to return to
the following value:
Count up
Count down
"000:00"
Timer that you set.
Attention
zz To stop the [P-timer] function, press the <P-TIMER>
button.
zz To cancel the [P-timer], press and hold the <P-TIMER>
button for a few seconds.
ENGLISH - 55
Settings
Direct on
Setting
Closed caption
The closed caption is mainly used in the north
America. This function shows the text information
contained in the image signal. Captions may not be
displayed on some devices or software.
1111 Press ▲▼ to select [Closed caption].
2222 Press ► or the <ENTER> button to
enter the submenu.
JJClosed caption
1111 Press ▲▼ to select [Closed caption]
and then press the <ENTER> button.
2222 Press ▲▼ to select Off, CC1, CC2,
CC3 or CC4.
JJColor
1111 Press ▲▼ to select [Color] and then
press the <ENTER> button.
2222 Press▲▼ to select color or white.
Attention
zz Closed caption is available only when Video, S-video
or Component is selected as the input signal and Auto,
NTST or 480i is selected from the System Menu.
zz Part of characters may not displayed when high
compensation values are set in [Keystone].
zz Closed captions are not displayed while the menu screen
appears.
Lamp power
This function allows you to change brightness of the
screen.
1111 Press ▲▼ to select [Lamp power] and
then press the <ENTER> button.
2222 Press ▲▼ to select one among the
modes as below.
zz You can also press the <LAMP> button to
display [Lamp power].
Normal
Brightness according to the input
signal.
Eco
Lower brightness reduces the
lamp power consumption and
extends the lamp life.
Remote control
This switching function prevents remote control
interference when operating several projectors or
video equipment at the same time.
1111 Press ▲▼ to select [Remote control].
2222 Press ► or the <ENTER> button.
3333 Press ▲▼ to select one among the
seven codes.
zz This projector provides 7 different remote
control codes: [ALL], [Code 1]~[Code 6].
Attention
Settings
zz When operating the projector under [ALL] code, you can
operate several projectors at the same time. If you want
to operate the projector independently, you must switch
to other code.
zz When different codes are set on the projector and on the
remote control, any operation cannot be made. In that
case, switch the code on the remote control to fit the
code on the projector.
zz If the batteries are removed from the remote control for a
long period of time, the remote control code will be reset.
56 - ENGLISH
Setting
JJPIN code change
Security
This function allows you to use the Key lock and PIN
code lock function to set the security for the projector
operation.
1111 Press ▲▼ to select [Security].
2222 Press ► or the <ENTER> button to
access the submenu.
JJKey lock
This function locks the control panel and remote
control buttons to prevent operation by unauthorized
persons.
1111 Press ▲▼ to select the desired items
as below.
Unlocked.
Lock the operation of the control
panel. To unlock, use the remote
control.
Lock the operation of the remote
control. To unlock, use the control
panel.
The PIN code can be changed to your desired fourdigit number.
1111 Press ▲▼ to select [PIN code change]
and then Press <ENTER> button.
zz Current Pin code dialog box appears.
2222 Press ▲▼ to enter the current code.
Press ► button to fix the number and
move the red frame pointer to the next
box.
zz The New PIN code input dialog box appears.
3333 Repeat these steps to set a new PIN
code.
Fan
1111 Press ▲▼ to select [Fan] and then
Press <ENTER> button.
2222 Press ▲▼ to select one option.
zz This function provides the following options in
the cooling fans’ operation when the projector is
turned off.
JJPIN code lock
L1
Normal operation.
This function prevents the projector from being
operated by unauthorized persons and provides the
following setting options for security.
L2
The fan speed is the same as
L1, but it takes more time to cool
the projector down.
Off
Settings
1111 Press ▲▼ to select the desired items
as below.
Unlocked.
On 1
Enter the PIN code every time
turning on the projector.
On 2
Enter the PIN code to operate
the projector once the power cord
is disconnected; as long as the
AC power cord is connected, the
projector can be operated without
a PIN code.
Attention
zz Whenever you change the PIN code lock setting or the
PIN code (the four-digit number), you are required to
enter the PIN code. The "1234" is set as the initial PIN
code at the factory.
ENGLISH - 57
Setting
Fan control
Lamp runtime
1111 Press ▲▼ to select [Fan control] and
then Press <ENTER> button.
2222 Press ▲▼ to select one among
options as below.
zz Choose the running speed of cooling fans from
the following options according to the ground
elevation under which you use the projector.
Off
Normal speed.*
1
On 1
Faster than Off mode.*2
On 2
Faster than On 1 mode.*3
***** Set this function to [Off] when using the projector
in non-high altitude environment.
***** Select this mode when using the projector in high
altitudes (about 1,200 meters or more above
the sea level) where the fans have less cooling
effect.
***** Select this mode when using the projector in
higher altitudes ( than above where the fans
have less cooling effect).
Note
zzFailure to set the running speed of cooling fans
properly may affect the projector life.
zzThe fan noise becomes louder in [On 1] and [On 2].
Video delay control
Settings
This function allows you to make a digital processing
of a projected image faster.
1111 Press ▲▼ to select [Video delay
control] and then Press the <ENTER>
button.
2222 Press ▲▼ to select one item between
On and Off.
Note
zz[Noise reduction] and [Progressive] can not be
selected when [Video delay control] function is set
to [On].
This function is used to display the cumulative lamp
operating time and reset the lamp runtime.
Press ▲▼ to select [Lamp runtime] and
then press ► or the <ENTER> button to
show submenus.
JJLamp runtime
Show the total accumulated lamp run time.
JJLamp runtime reset
After replacing the lamp unit, be sure to reset the
timer.
Press the <ENTER> button to reset.
zz[Lamp runtime Reset?] appears. Select [Yes] to
continue. Another confirmation dialog box appears,
select [Yes] to reset the Lamp runtime.
Attention
zzWhen the lamp run time is elapsed the estimated
duration, [Lamp runtime] will be displayed in red
and the Lamp replacement icon (Æpage 64) will
appear on the screen, indicating that the end of
lamp life is reached. When replacing the lamp unit,
reset the lamp runtime.
Filter counter
This function is used to set a frequency for the filter
replacement.
1111 Press ▲▼ to select [Filter counter].
2222 Press ►or the <ENTER> button to
access the submenu items.
JJFilter counter
Show the total accumulated time of the filter use timer
setting.
JJTimer
To set a timer. When the projector reaches the
selected time the filter warning icon appears on the
screen.
1111 Press ▲▼ to select [Timer] and then
press the <ENTER> button.
2222 Press ▲▼ to set the Timer.
zz Select from [Off/1000H/2000H/3000H/4000H]
depending on the use environment.
58 - ENGLISH
Setting
JJFilter counter reset
After replacing the filter, be sure to reset the timer.
1111 Press ▲▼ to select [Filter counter
reset].
2222 Press the <ENTER> button.
zz [Filter counter Reset?] appears. Select [Yes]
to continue. Another confirmation dialog
box appears, select [Yes] to reset the [Filter
counter].
Warning log
This function records anomalous operations while the
projector is in operation and use it when diagnosing
faults.
1111 Press ▲▼ to select [Warning log].
2222 Press ► or the <ENTER> button to
display the latest warning message.
zz Up to 10 warning logs are displayed with the
latest warning message at the top of the list,
followed by previous warning messages in
chronological order.
Attention
zzWhen the [Factory default] function is executed, all
the warning log records will be deleted.
Factory default
Settings
This function returns all setting values except for the
[PIN code lock], [Logo PIN code lock], [Lamp runtime],
[Filter counter] and the logo transferred by "Logo
Transfer Software" to the factory default settings.
1111 Press ▲▼ to select [Factory default].
2222 Press the <ENTER> button.
zz [Return to Factory default?] appears. Select
[Yes] to continue. Another confirmation dialog
box appears, select [Yes] to return to [Factory
default].
ENGLISH - 59
Information
Information
Select [Information] from the Main Menu (see
“Navigating through the menu” on page 36),
then select the item from the sub-menu.
Remote control
Control panel
JJLamp power
The selected lamp mode is displayed.
JJLamp runtime
The cumulative lamp operating time is displayed.
JJPower management
[Off] , [Ready] or [Shut down], and [timer] are
displayed.
JJKey lock
The selected Key lock icon is displayed.
Input Source Information
Display
The Information Menu is used for checking the status
of the image signal being projected and the operation
of the projector.
You can also Press the <INFO.> button on the remote
control to display the Information menu.
JJInput
The selected input source is displayed.
JJSystem
The selected system is displayed.
Settings
JJH-sync freq.
The selected H-sync freq. is displayed.
The horizontal frequency of the input signal is
displayed in KHz, or - - - - KHz when no signal.
JJV-sync freq.
The selected V-sync freq. is displayed.
The vertical frequency of the input signal is displayed
in Hz, or - - - - Hz when no signal. Numbers of Hz
doubles during Interlace.
JJScreen
The selected Screen size is displayed.
JJLanguage
The selected language is displayed.
60 - ENGLISH
JJPIN code lock
[Off], [On 1] or [On 2] is displayed.
JJRemote control
The selected remote control code is displayed.
JJSerial number
The serial number of the projector is displayed.
The serial number is used to service the projector.
LAMP and WARNING Indicators
LAMP and WARNING Indicators
Managing the indicated problems
If a problem should occur inside the projector, the <ON(G)/STANDBY(R)>, <LAMP> and/or <WARNING>
indicators will inform you. Manage the indicated problems as follow.
CAUTION
zz Before you take a remedial measure, follow the procedure of switching the power off indicated in “Turning Off the Projector”.
(Æpage 30)
zz If multiple indicators light or blink, verify the status of the projector by looking at each indicator.
Note
zz Confirm the status of the power indicated on the <ON(G)/STANDBY(R)> indicator.
JJLAMP indicator
Indicator
Lighting in yellow
Status
The projection lamp reaches its end of life.
Check
Is there a Lamp replacement icon appears on the screen?
Remedy
Replace the lamp unit. (Æpage 65)
Note
zz Contact your dealer for repair services when <LAMP> indicator persists to light after taking these measurements.
JJWARNING indicator
Status
Check
Remedy
Lights in red.
Blinks in red.
The projector detects an abnormal The temperature inside the projector is abnormally high.
condition and cannot be turned
The projector cannot be turned on. And the <ON(G)/
on.
STANDBY(R)> indicator also blinks in red.
Unplug the AC power cord
and plug it again to turn on the
projector.
- Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if the air
vents of the projector are not blocked.
- Has the projector been installed near an AirConditioning/ Heating Duct or Vent?
- Is the filter clean?
If the projector is turned off again, - Provide good installing condition to your projector.
unplug the AC power cord and
- Move the installation of the projector away from the duct
contact the dealer or the service
or vent.
center for service and checkup.
- Replace air filter unit.
Note
zz If <WARNING> indicator persists to light or blink after taking these measurements, please contact your dealer for repair
services. Do not leave the projector on. It may cause an electric shock or a fire hazard.
zz The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn
on the projector. If the projector is turned off again, unplug the AC power cord and contact the dealer or the service center
for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard.
ENGLISH - 61
Maintenance
Indicator
Replacement
Before replacing the unit
zz When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect
the power plug from the wall outlet. (Æpages 26, 30)
zz Be sure to observe the procedure “Turing Off the Projector” (Æpage 30) when performing power supply
operation.
Maintenance
JJOuter Case
Wipe off dirt and dust using a soft dry cloth.
zz If the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping. Dry off the projector
with a dry cloth.
zz Do not use benzene, thinner, or rubbing alcohol, other solvents, household cleaners, or chemical treated
dusters. Using them may cause deterioration of the outer case.
JJFront glass surface of the lens
Wipe off the dirt and dust off the front surface of the lens with soft clean cloth.
zz Do not use a cloth that has an abrasive surface or a cloth that is moist, oily, or covered with dust.
zz Do not use excessive force when wiping the lens as it is fragile.
Attention
zz The lens is made of glass. Impacts or excessive force when wiping may scratch its surface.
Please handle with care.
Maintenance
62 - ENGLISH
Replacement
Replacing the unit
JJAir filter unit
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter become
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup
and adversely affect the life of the projector.
If a “Filter warning” icon appears on the screen, replace the air filter unit immediately. Replace it with the
separately sold ET-RFT100 replacement filter unit. Consult your supplier when you purchase a replacement filter.
JJ Replacement of the air filter unit
1111 Remove the air filter cover.
zz Clean up the dust on the projector and around
the air vents. Press and hold the right-hand
corner of the filter cover, and then press
◄ leftwards on the filter cover to release the
latch and open the filter cover.
2222 Remove the air filter unit.
zz Put your fingers on the filter tab and then pull
the air filter unit out of the projector.
3333 Insert a new air filter unit.
Latch
Filter cover
zz Insert the new filter unit completely by following
the instructions for step 2 in the reverse order.
Ensure that the area with “TOP” mark is in an
upward direction.
TOP mark
4444 Install the air filter cover.
zz Insert the air filter unit cover by following the
instructions for step 1 in the reverse order.
Pull out and
remove.
JJ Resetting the Filter Counter
Be sure to reset the Filter counter after replacing the filter.(Æpage 59" Filter counter reset")
Attention
safe, even in the event of the air filter unit dropping.
zz Do not operate the projector with the air filter unit removed. Dust may accumulate on the optical elements
degrading picture quality.
zz Do not put anything into the air vents. Doing so may result in malfunction of the projector.
zz Do not wash the air filter unit with water or any other liquid matter. Otherwise the air filter unit may be damaged.
ENGLISH - 63
Maintenance
zz Turn off the power before you replace the air filter unit.
zz When attaching the air filter unit, make sure that the projector is stable, and work in an environment that is
Replacement
JJLamp unit
The lamp unit is a consumable component. You can check the total usage time using Lamp runtime in the
Information menu on page 60.
It is recommended to ask an authorized engineer to replace the lamp unit. Contact your dealer.
Consult your dealer to purchase a replacement lamp unit (ET-LAT100).
CAUTION:
■ Do not replace the lamp unit when it is hot. (Wait at least 1 hour after use.)
The inside of the cover can become very hot, take care to avoid burn injuries.
JJNotes on the replacement of the lamp unit
zz The luminous source of the lamp is made of glass and may burst
if you hit it against a hard surface or drop it. Please handle with
care.
zz A Phillips screwdriver is required for replacement of the lamp unit.
zz When replacing the lamp unit, be sure to hold it by the handle.
zz When replacing the lamp because it has stopped illuminating,
there is a possibility that the lamp may be broken. If replacing the
lamp of a projector which has been installed on the ceiling, you
should always assume that the lamp is broken, and you should
stand to the side of the lamp cover, not underneath it. Remove
the lamp cover gently. Small pieces of glass may fall out when
the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately.
zz The lamp contains mercury. Consult your local municipality or your dealer about correct disposal of used
lamp units.
Attention
zz Do not use other than designated lamp units.
zz The part numbers of accessories and separately sold components are subject to change without notice.
JJWhen to replace the lamp unit
The lamp unit is a consumable component. Brightness decreases according to duration of usage, so
periodical replacement of the lamp unit is necessary.
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the
screen and <LAMP> indicator lights yellow. Replace the lamp with a new one promptly.
Lamp runtime
Maintenance
Over 3000 hours *
Over 3200 hours *
On screen
Lamp replacement icon
The message is displayed for 10 seconds. If
you press any button within the 10 seconds, the
message disappears.
If the power is turned on without replacing the lamp,
the power automatically turns off after approximately
ten minutes to prevent the malfunction of the
projector.
LAMP indicator
Lights in yellow (even in
stand-by mode).
*3200 hours of use is a rough guideline, but is not a guarantee. The lamp runtime differs depending on the setting
of "Lamp power" menu.
Note
zzThe Lamp replacement icon will not appear when the [Display] function is set to [Off] (Æpage 53), or during
"Freeze" (Æpage 33), or "AV mute" (Æpage 34).
64 - ENGLISH
Replacement
JJReplacing the Lamp unit
CAUTION:
zz When the projector is mounted on a ceiling, do not work with your face close to the projector.
zz Attach the lamp unit and the lamp cover securely.
zz When you experience difficulty in installing the lamp, remove it and try again. If you use force to install the
lamp, the connector may be damaged.
1111 Turn off the Power by following the
procedure in "Turning Off the Projector"
(Æpage 28).Unplug the AC power cord.
Wait at least 1 hour and make sure
the lamp unit and surroundings are cool.
2222 Use a Phillips screwdriver to loosen
the lamp cover fixing screw and
remove the lamp cover.
Lamp cover
�
Lamp cover
fixing screw
zz Remove the lamp cover by pulling it slowly toward the
direction of the arrow.
Lamp unit fixing screws
3333 Use a Phillips screwdriver to loosen the
three lamp unit fixing screws until the
screws turn freely. Hold the used lamp
unit by its handles, and pull it gently from
the projector.
4444 Insert the new lamp unit in correct
direction. Tighten the three lamp unit
fixing screws securely with a Phillips
screwdriver
Handles
5555 Attach the lamp cover, and tighten the
lamp cover fixing screw securely with a
Phillips screwdriver.
zz Attach the lamp cover by pushing it slowly
opposite the direction of the arrow.
Maintenance
Lamp unit
JJResetting the Lamp Runtime
Be sure to reset the [Lamp runtime] after replacing the lamp. (Æpage 58 "Lamp runtime reset")
ENGLISH - 65
Replacement
Attaching the Lens Cover
When moving this projector or while not using it over an extended period of time, attach the lens cover.
Attach the lens cover according to the following procedures.
1111 Thread the string through the hole on the lens cover and then tie a knot in the string to secure it in place.
2222 To pass the other end of the string into the hole on the bottom of the projector and pull at it.
Attaching the Cable Holder and Ferrite Core
1111 Attach the ferrite core to the USB cable
as shown in the figure.
2222 Stick the adhesive cable holder
(supplied) on the bottom of the
projector and store the USB cable in
the holder to prevent the cable from
blocking communication between the
infrared remote receiver and remote
control as show in the figure.
150 mm
Cable holder (supplied)
Interactive camera
Ferrite core
USB cable
(supplied)
Attention
zz The USB cable with ferrite core must be used for RF
interference suppression.
Remote control operating range
Infrared remote receiver
Maintenance
66 - ENGLISH
Troubleshooting
Please check following points. For details, see the corresponding pages.
Reference
page
Cause
zz The power cord may not be connected.
—
zz No electric supply is at the wall outlet.
—
Power does not turn zz The circuit breakers have tripped.
on.
zz Is the <LAMP> indicator, <ON(G)/STANDBY(R)> indicator, or
<WARNING> indicator lit or blinking?
—
27, 61
zz The lamp cover has not been securely installed.
—
zz The video signal input source may not be connected to a terminal
25
zz The input selection setting may not be correct.
32
zz The [Brightness] adjustment setting may be at the minimum setting.
—
zz The input source which is connected to the projector may have a
—
zz The [AV mute] function may be in use.
34
zz The lens focus may not have been set correctly.
31
zz The projector may not be at the correct distance from the screen.
22
zz The lens may be dirty.
14
zz The projector may be tilted too much.
—
zz [Color] or [Tint] adjustment may be incorrect.
45
zz The input source which is connected to the projector may not be
—
zz RGB cable is damaged.
—
zz The input terminals may not have been correctly connected.
25
zz The volume may have been set to the minimum level.
34
zz The [AV mute] function may have been turned on.
34
zz When the AUDIO OUT is plugged-in, the projector's built-in speaker is
20
zz The [Mute] function may have been turned on.
35
zz The batteries may be weak.
—
zz The batteries may not have been inserted correctly.
21
zz The remote control signal receptor on the projector may be obstructed.
17
zz The remote control unit may be out of the operation range.
17
zz Strong light such as fluorescent shine onto the signal receptor.
17
zz When different codes are set on the projector and on the remote control.
57
zz The control panel is not available if the control panel is locked at [Key
57
properly.
No picture appears.
problem.
The picture is fuzzy.
The color is pale or
grayish.
No sound from the
internal speaker
adjusted correctly.
not available.
The remote control
does not operate.
The control buttons
of the projector do
not operate.
lock] under [Security] of [Setting] section.
The picture does not zz There may be a problem with the VCR or other signal source.
zz A signal which is not compatible with the projector is being input.
display correctly.
Picture from a
computer does not
appear.
—
—
zz The cable may be longer than the optional cable.
—
zz The external video output from a laptop computer may not be correct.
—
ENGLISH - 67
Maintenance
Problem
Troubleshooting
Problem
Picture from a HDMI
device does not
appear or picture is
not stable.
No sound is output
from a HDMI device.
Cause
zz Is the HDMI cable securely connected?
25
zz Turn off the power of the projector and the connected devices. Then turn
—
zz Isn't unsupported signal cable connected?
73
zz Set the sound channel of the attached device to Linear PCM.
—
zz If no audio signal is output during HDMI cable connection, connect the
54
the power of the projector and the connected devices back on.
audio cable to COMPUTER/COMPONENT AUDIO IN terminal and set
to "Computer" in "Sound" of "Setting" menu.
zz Check [PC adj.] or [Screen] and adjust them.
The image is
distorted or runs off.
The exclamation
mark
appears on
the screen.
Note
zz Your operation is invalid. Operate correctly.
zz If the problem persists, after confirming the contents of the table, please consult your dealer.
Maintenance
68 - ENGLISH
Reference
page
42, 48
—
Technical Information
Serial terminal
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface
specification, so that the projector can be controlled by a personal computer which is connected to this connector.
JJConnection
Connecting terminals
on projector
Computer
D-Sub 9-pin (male)
D-Sub 9-pin (female)
Communication cable
JJPin assignments and signal names
D-Sub 9-pin (male)
Outside view
Pin No.
Signal name
—
RXD
TXD
—
GND
—
—
—
—
Contents
NC
Received data
Transmitted data
NC
Earth
NC
NC
NC
NC
JJCommunication conditions
Signal level
Sync. method
Baud rate
Parity
RS-232C-compliant
Asynchronous
19200 bps
None
Character length
Stop bit
X parameter
S parameter
8 bits
1 bit
None
None
Note
zz When [AMX D. D.] function is set to [On] under the [Network] menu, the Baud rate will change to 9600 bps
Appendix
automatically.
ENGLISH - 69
Technical Information
JJBasic format
Transmission from the computer begins with STX, then the command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
STX
C1
Start
(1 byte)
C2
C3
:
P1
Colon
(1 byte)
3 command
characters
(3 bytes)
P2
Pn
Parameter
(undefined length)
ETX
End
(1 byte)
½½½ When sending commands without parameters, a colon (:) is not necessary.
JJBasic format (with sub command)
Same as basic format
STX
S1
C1
S2
S3
C2
C3
S4
Sub command (5 bytes)
:
S5
ETX
E
P1
P2
P3
P4
P5
P6
Parameter (6 bytes)
Symbol “+” or “-” (1 byte) and set value or
adjustment value (5 bytes)
Operation (1 byte)
“=” (Value specified using parameter is set)
½½½ When transmitting a command which does not need a parameter, the operation (E) and parameter are not
necessary.
Appendix
70 - ENGLISH
Technical Information
JJCable specifications
[When connected to a computer]
Projector
1
2
3
4
5
6
7
8
9
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
Computer (DTE
specifications)
JJControl commands
When controlling the projector from a computer, the following commands are available:
[Projector control command]
Control contents
PON
Power [ON]
POF
Power [OFF]
Remarks
IIS
INPUT selection
(Parameter)
VID = Video
SVD = S-video
RG1 = Computer 1(RGB)
RG2 = Computer 2(RGB)
HD1 = HDMI
SCT = Computer 1(Scart)
OSH
AV mute function
Turning off the projection and sound temporarily.
Sending the command switches ON/OFF.
Do not switch ON/OFF in a short period of time.
OFZ
Freeze
Sending the command switches ON/OFF.
AUU
Volume up
AUD
Volume down
DZU
D. ZOOM up
DZD
D. ZOOM down
QPW
Power query
000 = Standby
001 = Power on
Lamp condition
query
(Call back)
0 = Stand-by
1 = Lamp ON control active
2 = Lamp ON
3 = Lamp OFF control active
Q$S
Appendix
Command
ENGLISH - 71
Technical Information
Other terminals
JJPin assignments and signal names of <S-VIDEO IN> terminal
Pin No.
Outside view
Signal names
GND (luminance signal)
GND (color signal)
Luminance signal
Color signal
JJPin assignments and signal names of <COMPUTER IN 1/COMPONENT
IN> terminal
Pin No.
Outside view
Signal names
R/PR
G/G SYNC/Y
B/PB
+5V
DDC data
HD/SYNC
VD
DDC clock
: Not assigned
- , ,
: GND terminals
JJPin assignments and signal names of <COMPUTER IN 2/MONITOR OUT>
terminal
Pin No.
Outside view
Signal names
R
G
B
HD/SYNC
VD
,
-
,
,
,
,
: Not assigned
: GND terminals
JJPin assignments and signal names of <HDMI> terminal
Pin No.
Outside view
Even-numbered pins
to
Odd-numbered pins
to
Appendix
72 - ENGLISH
Signal names
T.M.D.S data 2+
T.M.D.S data 2 shield
T.M.D.S data 2T.M.D.S data 1+
T.M.D.S data 1 shield
T.M.D.S data 1T.M.D.S data 0+
T.M.D.S data 0 shield
T.M.D.S data 0T.M.D.S clock +
Pin No.
Signal names
T.M.D.S clock shield
T.M.D.S clock CEC
—
SCL
SDA
DDC/CEC GND
+5V
Hot plug detection
Technical Information
List of compatible signals
The following table specifies the types of signals compatible with the projectors.
Format : V
= VIDEO, S = S-VIDEO, C = COMPUTER, Y = YPBPR, H = HDMI
Scanning
frequency
V (Hz)
Dot clock
frequency
(MHz)
Picture
quality *2
15.7
59.9
—
A
V/S
15.6
50.0
—
A
V/S
H (kHz)
NTSC/NTSC4.43/
PAL-M/PAL60
720 x 480i
PAL/PAL-N/SECAM
720 x 576i
Mode
480p
640 x 480
31.47
59.88
25.20
A
480i
640 x 480i
15.734
60.00
12.2727
A
576p
768 x 576
31.25
50.00
29.50
A
576i
768 x 576i
15.625
50.00
14.75
A
720p
1280 x 720
1035i
1920 x 1035i
1080i
1920 x 1080i
640 x 480
VGA
SVGA
MAC
MAC 13
MAC LC13
37.50
50.00
74.25
A
45.00
60.00
74.25
A
33.75
60.00
74.25
A
50.00
74.25
A
33.75
60.00
74.25
A
31.47
59.88
25.149
A
○
37.86
74.38
31.50
A
○
37.86
72.81
31.50
A
○
37.50
75.00
31.50
A
○
43.269
85.00
36.00
A
31.47
70.09
25.175
A
720 x 400
31.47
70.09
28.322
A
35.156
56.25
36.00
A
○
37.88
60.32
40.00
A
○
46.875
75.00
49.50
A
○
53.674
85.06
56.25
A
○
48.08
72.19
50.00
A
37.90
61.03
40.02
A
34.50
55.38
36.432
A
38.00
60.51
40.128
A
38.60
60.31
38.60
A
32.70
51.09
32.70
A
38.00
60.51
40.128
A
C
1280 x 960
75.00
75.08
126.00
A
○
1280 x 1024
80.00
75.08
135.20
A
○
640 x 480
Format
C/Y
28.125
640 x 400
800 x 600
PnP
35.00
66.67
30.24
A
○
34.97
66.60
31.33
A
○
MAC 16
832 x 624
49.72
74.55
57.283
A
○
MAC 19
1024 x 768
60.24
75.08
80.01
A
○
MAC 21
1152 x 870
68.68
75.06
100.00
A
○
Appendix
Display
resolution *1
(dots)
***** “i” added to the resolution value indicates an interlaced signal.
***** Picture quality is indicated by the following symbols.
AA: Maximum picture quality can be obtained.
A: Signals are converted by the image processing circuit.
ENGLISH - 73
Technical Information
Mode
SXGA+
Dot clock
frequency
(MHz)
H (kHz)
63.970
60.190
107.99
A
1400 x 1050
65.350
60.120
122.85
A
65.120
59.900
122.43
A
48.36
60.00
65.00
A
68.677
84.977
94.504
A
○
60.023
75.03
78.75
A
○
○
1024 x 768
XGA
V (Hz)
Picture
quality *2
56.476
70.07
75.00
A
60.31
74.92
79.252
A
48.50
60.02
65.179
A
44.00
54.58
59.129
A
63.48
79.35
83.41
A
62.04
77.07
84.375
A
61.00
75.70
81.00
A
46.90
58.20
63.03
A
47.00
58.30
61.664
A
58.03
72.00
74.745
A
36.00
87.17
47.30
A
35.522
86.96
44.90
A
1152 x 864
64.20
70.40
94.56
A
61.20
65.20
92.00
A
1152 x 900
71.40
75.60
105.10
A
61.85
66.00
94.50
A
60.00
60.00
108.00
A
1024 x 768i
1280 x 960
SXGA
1280 x 1024
1280 x 1024i
UXGA
Scanning
frequency
Display
resolution *1
(dots)
1600 x 1200
62.50
58.60
108.00
A
63.90
60.00
107.35
A
63.34
59.98
108.18
A
63.74
60.01
109.497
A
71.69
67.19
117.004
A
81.13
76.107
135.008
A
63.98
60.02
108.00
A
79.976
75.025
135.00
A
63.37
60.01
111.52
A
76.97
72.00
130.08
A
63.79
60.18
108.19
A
91.146
85.024
157.5
A
50.00
86.00
80.00
A
50.00
94.00
80.00
A
46.43
86.70
78.745
A
75.00
60.00
162.00
A
Appendix
81.25
65.00
175.50
A
87.5
70.00
189.00
A
93.75
75.00
202.50
A
***** “i” added to the resolution value indicates an interlaced signal.
***** Picture quality is indicated by the following symbols.
AA: Maximum picture quality can be obtained.
A: Signals are converted by the image processing circuit.
74 - ENGLISH
PnP
Format
○
C
○
○
○
Technical Information
1280 x 768
WXGA
1280 x 800
1366 x 768
1360 x 768
Scanning
frequency
H (kHz)
V (Hz)
Dot clock
frequency
(MHz)
47.776
59.870
79.50
AA
60.289
74.893
102.25
AA
68.633
84.837
117.50
AA
55.993
69.991
94.964
AA
57.675
72.004
97.817
AA
49.600
60.050
79.36
AA
41.200
50.000
68.557
AA
49.702
59.810
83.50
AA
63.980
60.020
108.00
AA
58.289
69.975
98.858
AA
60.044
71.995
102.795
AA
62.790
74.928
106.492
AA
71.553
84.879
122.498
AA
48.36
60.00
86.67
A
47.70
60.00
86.67
A
56.16
72.00
100.19
A
Picture
quality *2
PnP
○
1376 x 768
48.36
60.00
86.67
A
WSXGA+
1680 x 1050
65.290
59.954
146.25
A
WXGA+
1440 x 900
55.935
59.887
106.50
A
74.918
60.000
161.85
A
WUXGA
1920 x 1200
D-VGA
D-480p
D-576p
640 x 480
768 x 576
74.556
59.885
193.25
A
74.038
59.950
154.00
A
Format
○
C
○
○
31.47
59.94
25.175
A
○
31.47
59.88
25.20
A
○
31.25
50.00
29.50
A
○
37.50
50.00
74.25
AA
○
D-720p
1280 x 720
45.00
60.00
74.25
AA
○
D-SVGA
800 x 600
37.879
60.32
40.00
A
○
D-XGA
1024 x 768
43.363
60.00
65.00
A
○
63.97
60.19
107.99
A
D-SXGA+
1400 x 1050
65.350
60.120
122.85
A
65.120
59.900
122.43
A
H
○
Appendix
Mode
Display
resolution *1
(dots)
***** “i” added to the resolution value indicates an interlaced signal.
***** Picture quality is indicated by the following symbols.
AA: Maximum picture quality can be obtained.
A: Signals are converted by the image processing circuit.
ENGLISH - 75
Technical Information
Mode
Display
resolution *1
(dots)
1360 x 768
1366 x 768
1376 x 768
1280 x 768
D-WXGA
1280 x 800
1280 x 768
D-SXGA
1280 x 1024
D-1035i
1920 x 1035i
D-1080i
1920 x 1080i
D-1080p
1920 x 1080
Scanning
frequency
H (kHz)
V (Hz)
Dot clock
frequency
(MHz)
Picture
quality *2
PnP
47.700
60.00
86.67
A
56.160
72.000
100.19
A
46.500
50.000
67.40
A
48.360
60.00
86.67
A
48.360
60.00
86.67
A
47.776
59.870
79.50
AA
60.289
74.893
102.25
AA
68.633
84.837
117.50
AA
49.572
59.870
83.282
AA
41.200
50.000
68.557
AA
49.702
59.810
83.50
AA
63.980
60.020
108.00
AA
58.289
69.975
98.858
AA
60.044
71.995
102.795
AA
62.790
74.928
106.492
AA
71.553
84.879
122.498
AA
55.993
69.991
94.964
AA
57.675
72.004
97.817
AA
63.98
60.02
108.00
A
60.276
58.069
93.067
A
31.65
29.8
53.48
A
33.75
60.00
74.25
A
28.125
50.00
74.25
A
○
33.75
60.00
74.25
A
○
○
○
H
○
67.5
60.00
148.50
A
○
56.25
50.00
148.50
A
○
D-WXGA+
1440 x 900
55.935
59.887
106.50
A
D-WSXGA+
1680 x 1050
65.290
59.954
146.25
A
D-WUXGA
1920 x 1200
74.038
59.950
154.00
A
Format
***** “i” added to the resolution value indicates an interlaced signal.
***** Picture quality is indicated by the following symbols.
AA: Maximum picture quality can be obtained.
A: Signals are converted by the image processing circuit.
***** Where marked "○" signals indicates in Plug and Play is compatible with EDID of projector. Unmarked signals
in Plug and Play may also be compliant if input terminals are written in the format list. Where Plug and Play
is unmarked and nothing is wirtten in the format list, difficulties in projecting image may occur even when
computer and projector appear to have same resolution.
Note
zz The number of display dots is 1280 x 800.
Appendix
A signal with a different resolution will be projected after converting the resolution to match the projector
display.
zz When interlaced signals are connected, flicker may occur on the projected image.
76 - ENGLISH
Specifications
Model No.
Power supply
PT-TW231RU
AC100 V - 240 V
50 Hz/60 Hz
100 V - 240 V 3.6 A - 1.8 A 310 W
Power consumption
When [Standby mode] of [Setting] is set to [ECO]: 0.42W
When [Standby mode] of [Setting] is set to [Network]: 9.5W
Panel size
LCD panel
Display method
Drive method
Pixels
3 transparent LCD panels (RGB)
Active matrix method
1 024 000(1 280 x 800) x 3 panels
Manual focus
F 1.8 , f= 6.68 mm
Lens
Luminous lamp
Light output
*1
for RGB signal
Applicable
scanning
frequency
*2
1.5 cm (0.59") (aspect ratio 16 : 10)
for YPBPR signal
for Video signal
(including S-video)
for HDMI signal
Color system
Projection size
230 W UHM lamp
2500 lm
Horizontal 15 kHz to 100 kHz, Vertical 50 Hz to 100 Hz
Dot clock frequency: 140 MHz or less
[525i(480i)]
Horizontal 15.75 kHz, Vertical 60 Hz
[525p(480p)]
Horizontal 31.5 kHz, Vertical 60 Hz
[750(720)/60p]
Horizontal 45 kHz, Vertical 60 Hz
[1125(1080)/60i]
Horizontal 33.75 kHz, Vertical 60 Hz
[625i(576i)]
Horizontal 15.63 kHz, Vertical 50 Hz
[625p(576p)]
Horizontal 31.25 kHz, Vertical 50 Hz
[750(720)/50p]
Horizontal 37.5 kHz, Vertical 50 Hz
[1125(1080)50i]
Horizontal 28.13 kHz, Vertical 50 Hz
zzHD/SYNC and V terminals are not compliant with 3 value composite SYNC
Horizontal 15.75 kHz / 15.63 kHz, Vertical 50 Hz / 60 Hz
525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60p, 1125(1080)/50p,
1125(1080)/60i, 1125(1080)/50i
zzDisplayable resolution: VGA to WUXGA (non-interlace)
zzDot clock frequency: up to 162 MHz
7 (NTSC, NTSC4.43, PAL, PAL-N, PAL-M, SECAM, PAL60)
1.52 m -2.79m (60"-110")
Screen aspect ratio
16 : 10
Projection scheme
Front / Rear / Mount on Ceiling / Floor (Menu setting system)
Speaker
Maximum usable volume output
Contrast ratio *1
1 (3.7 cm round-type)
10W
500 : 1 (all white / all black)
Appendix
***** Measurement, measuring conditions and method of notation all comply with ISO21118 international
standards.
***** For details of video signals that can be projected using this projector, refer to “List of compatible signals”.
(Æpage 73 to 76)
ENGLISH - 77
Specifications
Model No.
COMPUTER IN 1/
COMPONENT IN
1 (D-sub 15 pin female)
[RGB signal]
0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 [p-p] 75 Ω
HD/SYNC TTL high impedance, automatic positive/negative polarity compatible
VD TTL high impedance, automatic positive/negative polarity compatible
[YPBPR signal] Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
COMPUTER IN 2/
MONITOR OUT
[RGB signal]
Terminals
VIDEO IN
S-VIDEO IN
HDMI IN
AUDIO IN
AUDIO OUT
CONTROL PORT
LAN
Power cable length
Cabinet
0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 [p-p] 75 Ω
HD/SYNC TTL high impedance, automatic positive/negative polarity compatible
VD TTL high impedance, automatic positive/negative polarity compatible
1 (RCA pin jack 1.0 V [p-p] 75 Ω)
1 (Mini DIN 4 pin, Y 1.0 V [p-p], C 0.286 V [p-p] 75 Ω, S1 signal compatible)
1 (HDMI 19 pin, HDCP and Deep color compatible)
1 (M3 stereo mini jack, 0.5 V [rms], input impedance 22 kΩ and more)
1 (RCA pin jack x 2 (L-R), 0.5 V [rms], input impedance 22 kΩ and more)
1 (M3 stereo mini jack, stereo monitor output compatible,
0 V [rms] to 2.0 V [rms] valuable, output impedance 2.2 kΩ and less)
1 (D-sub 9 pin, RS-232C compliant, for computer control use
1 (for RJ-45 network connection, PJLink compatible,)
2.0 m (6.6')
Molded plastic
Width: 350 mm (13.78") (excluding protractions)
Height: 143.4 mm (5.65") (when front adjustable feet shortened)
Depth: 381.9 mm (15.04") (excluding protractions)
Dimensions
Weight
Approx.4.7 kg (10.4 lbs.) *3
Operating environment
Power supply
Remote
control
PT-TW231RU
Operating range
Weight
Dimensions
Operating environment temperature : 0 °C (32 °F) to 35 °C (95 °F)
Operating environment humidity: 20 % to 80 % (no condensation)
DC 3 V (battery (AAA/R03 Type ) x 2)
Approx. 5 m (196.9") (when operated directly in front of receptor)
67 g (2.36 ozs.) (including batteries)
Width : 52 mm (2.05"), Length : 110 mm (4.33"), Height : 18 mm (0.71")
***** This is an average value. It may differ depending on individual product.
zz The part numbers of accessories and separately sold components are subject to change without notice.
Appendix
78 - ENGLISH
Ceiling mount bracket
Specifications
safeguards
Dimensions
<Unit : inch (mm)>
½½½ Actual dimension may differ by product.
6.56(166.7)
6.29(159.8)
1.14(29)
4.53(115)
5.65(143.5)
0.34(8.7)
2.51(63.8)
4.33(110)
0.70(17.8)
1.46(37.1)
0.55(14)
7.53(191.3)
0.56(14.2)
0.72(18.3)
3.54(90)
5.46(138.7)
7.09(180)
7.09(180)
13.78(350)
10.94(277.8)
1.65(42)
2.76(70)
5.60(142.2)
3.94(100)
6.77(172)
15.11(383.8)
Ceiling mount bracket safeguards
zz Installation work of the ceiling mount bracket should only be carried by a qualified technician.
zz Even if it is during guaranteed period, the manufacturer is not responsible for any hazard or damage caused
by using a ceiling mount bracket which is not purchased from an authorized distributors, or environmental
conditions.
zz Remove an unused ceiling mount bracket promptly.
zz Ensure to use a torque driver and do not use an electrical screwdriver or an impact screwdriver.
zz For details, see the work instruction manual packed together with the ceiling mount bracket.
zz The model Nos. of the accessories and the parts sold separately are subject to change without notice.
zz Make sure the screws on the ceiling mount kit cannot touch the metal parts materials (metallic lath, wire or
board) in the ceiling board. Otherwise it may result in fire hazard.
Model No. of ceiling mount bracket:
ET-PKV100H (for high ceilings)
ET-PKV100S (for low ceilings)
Model No. of projector mount base:
ET-PKT100B
M5 x 0.7
Appendix
Bottom view
12 mm(0.47)"
Torque: 1.2 ± 0.1N.m
ENGLISH - 79
Index
A
About Your Projector.......................17
Accessories.....................................15
Adjusting front adjustable feet.........24
Attaching the Lens Cover................66
AUTO PC adjust..............................41
Auto setup.......................................52
AV MUTE.........................................34
B
Background.....................................53
Basic operations by using the
remote control..............................32
Blackboard(Green)..........................44
Brightness.......................................45
C
Cautions on use..............................14
Cautions when installing..................12
Cautions when transporting.............12
CD-ROM..........................................16
Ceiling.............................................50
Cinema............................................44
Closed caption.................................56
Color................................................45
Colorboard.......................................44
Color temp.......................................45
Computer System Selection............39
Connecting......................................25
Connecting the power cord.............26
Contrast...........................................45
Control panel...................................19
Custom............................................48
Custom adj......................................49
D
Digital zoom.....................................49
Direct on..........................................55
Direct Power Off function.................30
Display.............................................53
Disposal...........................................13
Dynamic..........................................44
F
Fan..................................................57
Fan control......................................58
Filter counter...................................58
FREEZE..........................................33
Full...................................................48
G
Gamma............................................46
H
HDMI setup.....................................54
How to adjust the state of the
image...........................................31
Appendix
I
ID numbers......................................21
Image adjust....................................45
Image select....................................44
Information......................................60
Input menu......................................39
Input search.....................................52
80 - ENGLISH
Installing and Removing batteries...21
K
Keystone.........................................49
L
LAMP and WARNING Indicators.....61
LAMP indicator................................61
Lamp power.....................................56
Lamp runtime..................................58
Lamp unit.........................................64
Language........................................52
List of compatible signals................73
Logo................................................53
M
Main menu.......................................37
Maintenance....................................62
Managing the indicated problems...61
Manual PC adjust............................42
Menu Navigation.............................36
Menu position..................................52
Mute................................................51
N
Natural wide....................................48
Noise reduction...............................46
Normal.............................................48
O
ON(G)/STANDBY(R) indicator.........27
Optional accessories.......................16
Other terminals................................72
P
PIN code..........................................29
PIN code Protection........................29
Power management........................54
Precautions for Use.........................12
Progressive.....................................47
Projecting........................................31
Projection distance..........................23
Projection method...........................22
Projector body.................................18
P-Timer............................................55
R
Read this first!...................................2
Real.................................................44
Rear.................................................50
Rear terminals.................................20
Remote control..........................17, 56
Replacing the Lamp unit..................65
Replacing the unit............................63
Resetting the Lamp Runtime...........65
S
Screen.............................................48
Screen aspect.................................50
Screen size and throw distance......23
Security.....................................13, 57
Selecting the image.........................31
Serial terminal.................................69
Setting.............................................52
Setting the ID number.....................21
Setting up........................................22
Sharpness.......................................46
Sound..............................................51
Specifications..................................77
Standard..........................................44
Standby mode.................................55
Sub menu........................................37
Switching the input signal................32
T
Terminal...........................................54
Tint...................................................45
Troubleshooting...............................67
True.................................................48
Turning Off the Projector.................30
Turning On the Projector.................28
V
Video delay control..........................58
Video System Selection...................39
Volume............................................51
W
WARNING indicator.........................61
Warning log.....................................59
Wide(16:9).......................................48
Z
Zoom...............................................48
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household
waste. For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points, in accordance with your national legislation and the
Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources
and prevent any potential negative effects on human health and the environment which could
otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact
your local municipality, your waste disposal service or the point of sale where you purchased the
items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier
for further information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
Panasonic Corporation
Web Site : http://panasonic.net/avc/projector/
© Panasonic Corporation 2012
SS0212-0