Eureka 6830 SERIES Vacuum Cleaner User Manual

®
VACUUM CLEANER
Household Type
OWNER’S GUIDE
6830 SERIES
IMPORTANT
Do not return this product to the
store.
For assembly problems or
q u e s t i o n s c o n t a c t : E u r e k a ’s
Customer Service Division
toll
free at 1-800-282-2886*, 8 a.m. to 7:
30 p.m., (CST), Monday - Friday and
10 a.m. to 6:30 p.m. Saturday.
For replacement of broken or
missing items to be shipped direct
to you, call 1-800-438-7352*, 8 a.m. to
4:45 p.m., (CST), Monday - Friday.
To order replacement parts and
accessories call 1-800-438-7352*,
8 a.m. to 4:45 p.m., (CST), Monday
- Fr iday or visit our web site,
www.eureka.com.
Index
Important Information ... 2
Assemble ...................... 3
Use ............................... 3
Accessories .................. 4
Filter.............................. 4
Dust Bag ....................... 4
Brush Roll ..................... 5
Brush Roll Belt .............. 5
Warranty ....................... 5
Part No. 73350 (02/04)
Please Retain
We suggest you record the model, type and serial numbers
below. They are located on the silver rating plate on your
cleaner. For prompt and complete service information, always
refer to these numbers when inquiring about service.
Model& Type____________________
Serial No. ______________________
It is also important to keep your receipt as proof of date of
purchase.
©2004 White Consolidated, Ltd.
Printed in U.S.A.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following :
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury :
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off
the switch and unplug the electrical cord when not in use
and before servicing.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If vacuum cleaner
is not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to a service
center before using.
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Do not run vacuum cleaner over cord. Keep cord away
from heated surfaces.
• Hold plug when rewinding onto cord reel. Do not allow plug
to whip when rewinding.
• Do not use extension cords or outlets with inadequate
current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• The hose contains electrical wires. Do not use when damaged,
cut, or punctured. Avoid picking up sharp objects.
• Always turn off this appliance before connecting or
disconnecting either hose or motorize nozzle.
• Do not handle plug or vacuum cleaner with wet hands or
operate without shoes.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair, and anything
that may reduce airflow.
• This vacuum cleaner creates suction and contains a
revolving brush roll. Keep hair, loose clothing, fingers, and
all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such
as cigarettes, matches, or hot ashes.
• Do not use without dust bag or filter in place.
• Belt pulleys can become hot during normal use. To prevent
burns, avoid touching the belt pulley when servicing the
drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such
as gasoline, or use in areas where they may be present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug does not
fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install the proper outlet. Do
not change the plug in any way.
DO NOT OIL the motor or the brush roll. The
motor and brush roll are permanently sealed
and lubricated.
GENERAL INFORMATION
Use the cleaner to pick up dirt and dust particles. Avoid
picking up hard or sharp objects that could damage the
vacuum cleaner.
Service Information
The instructions in this booklet serve as a guide to routine
maintenance. For additional service information, telephone
our toll free number for the nearest Eureka Authorized
Warranty Station. You should know the model, type and
serial number or date code when you call :
USA : 1-800-282-2886 Mexico : 5670-6169
Canada : 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service
Division, 807 North Main St., Bloomington, Illinois 61701,
USA. In Canada, write to The Eureka Company, 866 Langs
Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka
Warranty for complete service information.
2
Automatic Motor Shut-Off
To protect from overheating, this vacuum cleaner is
equipped with a thermostat which automatically shuts off
the motor if it overheats. Should this happen:
1. Turn off the switch and unplug the cleaner because
the thermostat will allow the cleaner to automatically
start running again when the motor cools (approximately
30 minutes).
2. Check the hose, bag and filter regularly, as a clogged
hose, full bag or dirty filter could cause the motor to
overheat.
3. Call a Eureka Service Station if the cleaner will not operate after cooling for approximately 30 minutes.
IDENTIFY PARTS OF CLEANER
7
2
1
ASSEMBLY
3
3a
4
5
8
1
Snap interlocking wands
together.
2
Push assembled wands into
power nozzle.
3
Place Power-Touch hose
handle into wands until plug
connects and button locks.
4
Insert hose coupling into top
of canister.
6
1.
2.
3.
3a.
4.
5.
6.
7.
Cord Rewind Pedal.
On/Off Pedal.
Bag Indicator (on some models)
Tool Cover Latch
Hose Inlet
Bag Cover Latch (on top of bag cover)
Carrying Handle (on the bottom)
Variable Speed Control
3
1
Quick Release Foot Pedal
(on some models) Press
down on pedal for quick
release of wands from
powerhead.
2
6
4
7
8
5
9
10
Pull electric plug out from
back of cleaner push plug
into outlet. To rewind, step on
Cordaway cord reel button,
hold and guide plug while it
rewinds.
5
NOTE: When pulling on electric cord watch for
a yellow line on the cord. Then continue slowly
pulling on cord till you see the red line, stop. The
red line indicates the end of usable cord.
HOW TO USE
8. Exhaust Filter
9. Motor Filter (behind dust bag)
10. Disposable Dust Bag
A carpet should be cleaned regularly over heavily traveled
areas, and once a week over the entire carpeted area.
Vacuum slowly, making several passes (forward and backward) over the carpet, covering small areas at a time. The
time required to clean the carpet will depend on several
factors–including type of carpet and amount of dirt.
11
11. Electric Cord
6
Step on handle release on the motorized nozzle to
release handle; pull back to comfortable work position.
7
Push ON/OFF Pedal
(A thermostat automatically shuts the motor off if it
overheats, see Automatic Motor Shut-Off)
8
Bare floor or carpet cleaning selection on remote
control, only. See page 4.
3
HOW TO USE (continued)
POWER-TOUCH® Handle
Bag Change Indicator
Vacuum Control
The bag change indicator bar fills as the airflow through the
bag decreases. Certain types of fine particles like powder,
plaster dust, or carpet fibers can restrict airflow very quickly
and will decrease performance even before the bag appears
to be full. When the warning appears, change the disposable
dust bag to restore maximum performance. If a clean dust
bag does not restore maximum performance, clean the filters
and check the hose and wands for obstructions.
F
OF
ON
Remote ON/OFF Selector for bare floor or carpet
ON – push down on front
*Off – push down on back for bare floors.
Cleaning suction is reduced by pushing lever to
LOW position. Place lever at HIGH position to
increase suction for carpet cleaning.
*Power ON/OFF for canister can only be controlled by canister
ON/OFF switch.
Cleaning Tools
Crevice Tool (stored inside cleaner): For
crevices, corners, baseboards, between
cushions.
Dusting Brush (stored inside cleaner):
For furniture, blinds, books, lamp shades,
shelves.
Upholstery Nozzle (stored inside cleaner):
For curtains, draperies, cushions, fabrics.
Turbo Brush: (on some models) For upholstery
and for stairs.
Empty Bag
Filled Bag
HOW TO CHANGE DISPOSABLE DUST BAG
- Style CN2 and FILTER - Style EF3
NOTE: Turn off the power switch and disconnect
electrical cord from wall socket before
changing dust bag. Never use the cleaner
without a dust bag or filters.
To remove used dust bag and check filters:
1. Unplug the hose from the bag compartment lid.
2. Squeeze bag compartment latch and swing lid up.
3. Lift exhaust filter out of bag compartment. If dirty, clean
or replace. The filter can be cleaned by brushing over a
waste receptacle. Place filter back in bag compartment.
4. Grasp bag collar and lift used bag out of cleaner and throw
away.
5. Pull down on motor filter grille to release the motor filter.
If dirty, clean or replace. The filter can be cleaned by
brushing over a waste receptacle. Replace filter in grille,
rotate grille up and push against cleaner to latch.
Bare Floor Brush: (on some models) For any type
of hard surface floor.
3.
HOW TO MAINTAIN
The paper bag and filters play a very important role in the
efficiency of the vacuum cleaner. The purpose of the paper
bag is to trap dirt and at the same time the paper must be
porous enough to allow air to pass through. If the paper bag
or filters become clogged, no air can pass through the cleaner
and no cleaning takes place regardless of how powerful the
unit. To keep the cleaner operating at maximum efficiency,
change the dust bag frequently and clean the filters as
necessary.
Some fine particles can restrict airflow very quickly and will
decrease performance even before the bag appears to be
full. When vacuuming carpet fresheners or cleaners, plaster
dust, or similar fine substances, clean the bag and filters
more often.
4
4.
5.
To install disposable dust bag:
1. Hold dust bag by collar and push dust bag into bag
frame.
2. Rotate bag compartment lid down and press against
cleaner until it latches.
Brush Roll
The brush roll turns to sweep and comb the carpet nap. Keep
the brush roll free from hair and threads so it will continue
cleaning. When the bristles of the brush roll no longer touch
a piece of cardboard held across the bottom plate, the brush
roll is ineffective because the bristles no longer touch the
carpet nap. To maintain the most effective cleaning, install a
new brush roll.
Brush Roll Belt and Light Bulb
The brush roll belt on the motorized nozzle drives the brush
roll to agitate, sweep, and comb the carpet nap. The belt
should be checked regularly to be sure that it is in good
condition. Replace the belt if it is broken, stretching, cracking,
or slipping. Cut away any hair or thread wound around the
brush roll or belt pulley because the buildup could cause the
belt to rotate unevenly.
How to Replace Worn Belt or Light Bulb
(On Some Models)
NOTE: Turn off the switch and unplug the electrical cord
before replacing belt or bulb. Pulleys can become
hot during normal use. To prevent injury, avoid
touching the pulleys when servicing the drive
belt.
THE EUREKA LIMITED WARRANTY
hat This Warranty Covers
WYour
Eureka cleaner is warranted to be free from all defects in material and workmanship
in normal household use for a period of one year. The warranty is granted only to the
original purchaser and members of his or her immediate household. The warranty is
subject to the following provisions.
This Warranty Does Not Cover
W•hat
Parts of the cleaner that require replacement under normal use, such as disposable dust
bags, filters, drive belts, light bulbs, brush roll bristles, impellers and cleaning.
• Damages or malfunctions caused by negligence, abuse, or use not in accordance with the
Owner’s Guide.
• Defects or damages caused by unauthorized service or the use of other than Genuine
Eureka parts.
hat The Eureka Company Will Do
WThe
Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part
that is covered by this warranty. As a matter of warranty policy, the Eureka Company
will not refund the consumer’s purchase price.
Warranty Registration
Please fill out and return the warranty registration card accompanying your cleaner.
Warranty Service
Obtaining
To obtain warranty service you must return the defective cleaner or cleaner part along with
1. Remove six screws from
bottom side. Turn unit
over; pull up on hood to
remove.
proof of purchase to any Eureka Authorized Warranty Station.
You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service
and Repair.” Be certain that the Warranty Station is “Eureka Authorized.”
For the location of the nearest Eureka Authorized Warranty Station or for service information
visit www.eureka.com, or telephone toll free: USA: 1-800-282-2886, Mexico: 5670-6169,
Canada: 1-800-282-2886.
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main
Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company,
866 Langs Drive, Cambridge, Ontario N3H 2N7.
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you
must pay the shipping charges to the Eureka Authorized Warranty Station.
Return shipping charges will be paid by the Warranty Station. When returning parts for repair,
please include the model, type, and serial number from the data plate on the cleaner.
Replace light bulb,
i f n e c e s s a r y. U s e
GENUINE EUREKA
replacement bulb,
59045.
Continue to step 2
to change belt. Skip
to step 7 to replace
hood.
Limitations and Exclusions
Further
Any warranty that may be implied in connection with your purchase or use of the cleaner,
Motor Pulley
including any warranty of Merchantability or any warranty for Fitness For A Particular
Purpose is limited to the duration of this warranty. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitations may not apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above.
In no event shall Eureka be liable for any consequential or incidental damages you
may incur in connection with your purchase or use of the cleaner. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary
by state..
2. Lift out brush roll and
discard used belt.
3. Put new belt around
brush roll pulley first;
then the motor pulley.
For Genuine Eureka Value, Accept No Imitations!
THE EUREKA COMPANY
4. Place left end cap into the
base.
Bloomington, Illinois 61701
5. Pull right end of brush
roll to stretch belt. Secure
right end cap into base.
6. Rotate brush roll to seat
belt.
7. Position hood; secure
with screws.
Brush
Roll
Pulley
Use GENUINE EUREKA replacement belt, 58065A.
5
Download PDF

advertising