Euro-Pro 9110 Sewing Machine User Manual

Another quality product from
Model 9110
SYMBOL INSTRUCTIONS
Raise needle
Raise presser foot
Lower presser foot
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety should always be followed, including the
following:
Read all instructions before using this sewing machine.
DANGER -To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately after using and before
cleaning.
3. Always unplug before checking and re-lamping. Contact the manufacturer or its service
agent for repair in the event of failure if the machine is with 240mW LED lamp, which is
not user-replaceable. Replace bulb with same type rated 5 watts if the machine is with
5W lamp.
WARNING -To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Do not allow to be used as a toy. Close attention is necessary when this appliance is
used by or near children.
2. Use this appliance only for its intended use as described in this manual. Use only the
attachments recommended by the manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly,
if it has been dropped or damaged, or dropped into water. Return the appliance to the
nearest authorized dealer or service center for examination, repair, electrical or
mechanical adjustment.
4. Never operate the appliance with any air openings block. Keep ventilation openings of the
sewing machine and foot controller free from accumulation of lint, dust, and loose cloth.
5. Keep fingers away from all moving parts. Special care is required around the sewing
machine needle.
6. Always use the proper needle plate, a wrong needle plate can cause the needle to break.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
9. Switch the sewing machine off ("O") when making any adjustments in the needle area,
such as threading needle, changing needle, threading bobbin, or changing presser foot,
and the light.
10.Always unplug sewing machine from the electrical outlet when removing covers,
lubricating, or when making any other user servicing adjustments mentioned in the
instruction manual.
11.Never drop or insert any object into any opening.
12.Do not use outdoors.
13.Do not operate where aerosol spray products are being used or where oxygen is being
administered.
14.To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.
15.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
SAVE THESE INSTRUCTIONS
This sewing machine is intended for household use only.
CONTENTS
PRINCIPAL PARTS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
BUTTONS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
LCD SCREEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PATTERN CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CONNECTING THE MACHINE TO THE POWER SOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STARTING SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Foot control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ADJUSTING THE PRESSER FOOT PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CHANGING THE PRESSER FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
REPLACING THE NEEDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MATCHING NEEDLE/ FABRIC/ THREAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TYPE OF PRESSER FOOT CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
WINDING THE BOBBIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Bobbin winding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INSERTING THE BOBBIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
THREADING THE UPPER THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
USING THE NEEDLE THREADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
THREAD TENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RAISING UP THE LOWER THREAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CUTTING THE THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TWO-STEP PRESSER FOOT LIFTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
TO RAISE OR DROP THE FEED DOGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
OPERATION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Reverse button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auto-lock button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Needle up/ down position button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FUNCTION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-25
Stitch width adjustment button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Stitch length adjustment button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MODE selection button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Elongation button (see page 56). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Mirror button (see page 57) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Twin needle button (see page 58) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SELECTION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Direct pattern selection and number buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clear button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Edit button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Memory button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
USEFUL SKILLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
Sewing corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Reverse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Free arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Sewing on the heavy fabric. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
STRAIGHT STITCHES AND NEEDLE POSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ZIGZAG STITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
STRETCH STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
OVERCASTING STITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CONTENTS
Using the overcasting foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the all purpose foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
BLIND HEM/ LINGERIE STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
BUTTON SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
BUTTONHOLE STITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-38
Making a buttonhole on stretch fabrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
ADJUSTING PATTERN BALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
EYELET STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DARNING STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-42
ZIPPER INSERTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-44
Inserting a centered zipper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Inserting a side zipper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
NARROW HEMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
CORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Single cording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Triple cording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
SATIN STITCH SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
QUILTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
GATHERING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SMOCKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . 51-52
Darning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Embroidery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Monogramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
WALKING FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FAGOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
PATCHWORK STITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SCALLOP STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Scallop hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Scallop edging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
ELONGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
MIRROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
USING THE TWIN NEEDLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
MEMORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-62
Combining patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Adding patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Editing patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Clearing patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Recalling and sewing the memorized pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
WARNING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-64
Warning animation message display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Instruction animation message display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Warning beeping sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
BUZZER SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
REPLACING THE LIGHT BULB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67-68
Cleaning the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Cleaning the sewing machine surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Cleaning the hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67-68
TROUBLE SHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69-70
QUICK ADJUSTMENT REFERENCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71-73
PRINCIPAL PARTS OF THE MACHINE
PRINCIPAL PARTS OF THE MACHINE
Upper thread guide
Horizontal spool pin
Bobbin thread guide
Hole for second
spool pin
Tension dial
Bobbin winder
with on/off switch
Thread take-up lever
Flip-top sewing
instruction panel
5
4
3
Top cover
Face plate
LCD screen
Presser foot pressure
B Function buttons
Operation buttons A
Thread cutter
C Selection buttons
Buttonhole lever
Speed limiting
adjustment lever
Auto needle threader
Needle plate
Sewing table and
accessory box
Handle
Handwheel
Main power switch
Presser foot lifter
Power cord
Feed balancing dial
Drop feed lever
Foot controller connector
1
BUTTONS OF THE MACHINE
BUTTONS OF THE MACHINE
5
4
3
2
1
7
6
8
B
A
9
10
C
1
2
3
4
5
6
7
8
9
0
11
12
13
14
15
A. Operation buttons (see page 21/22)
1. Start/stop button
Press this button to start or stop the machine.
2. Reverse button
Hold down this button to sew either backwards or a reinforcement stitch at a low speed.
3. Auto-lock button
Hold down this button to sew locking stitches immediately or at the end of the current patterns
and automatically stop.
4. Needle up/down position button
Press this button to move the needle either up or down.
B. Function buttons (see page 23/24/25)
5. Stitch width adjustment button
Press this button to adjust the width of the zigzag stitch.
6. Stitch length adjustment button
Press this button to adjust the length of the stitch.
2
BUTTONS OF THE MACHINE
BUTTONS OF THE MACHINE
7. Mode selection button
Press this button to select direct mode, utility and decorative pattern mode, block letter mode,
script letter mode and outline letter mode.
8. Elongation button
Pattern 30 to 39 can be elongated up to five times its normal length by pressing this button.
9. Mirror button
Press this button to sew a reflection pattern.
10.Twin needle button
Press this button to fix the width range when using the twin needle to sew.
C. Selection buttons (see page 26/27)
11.Direct pattern selection and number buttons
Instant access to direct pattern or press number buttons of the pattern number to select the
desired pattern.
12.Clear button
If an incorrect pattern is selected or memorized, pressing this button will clear it.
13.Edit button
Press this button to set an added pattern when sewing combinations of decorative stitches.
14.Memory button
Press this button to enter or store the created pattern combination in the memory.
15.Speed limiting adjustment lever
Slide this lever to change the sewing speed.
3
LCD SCREEN
LCD SCREEN
Pattern
Tension Suggested presser foot and number
Auto-lock
Pattern
number
Needle up/down position
Reverse
Pattern
Mirror
Sound on/off
Needle position
Stitch length
Auto-stop
Stitch width
Alphabet
Tension
Suggested presser foot and number
Needle up/down position
Alphabet number
Pattern
Sound on/off
Stitch width
Stitch length
Memory
Memory group
Number of current unit
Stitch width
Total number of unit
Stitch length
Needle up/down position
Sound on/off
Pattern for selecting Mirror
4
Auto-lock
PATTERN CHART
PATTERN CHART
The portion marked in purple on the chart below shows the one unit of each pattern.
Patterns
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
20
21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39
40
41 42 43 44 45 46 47 48 49 50
51 52 53 54 55 56 57 58 59
60
61 62 63 64 65 66 67 68 69 70
71 72 73 74 75 76 77 78 79
80
81 82 83 84 85 86 87 88 89 90
91 92 93 94 95 96 97 98 99
Alphabets
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
Block style
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
Script style
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
V
Outline style
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
5
X
ACCESSORIES
ACCESSORIES
Following the directions of the arrows, you can see the three accessory storage spaces (a), (b), (c).
Standard accessories
a
1. All purpose foot (T)-006186008
3
7
2. Zipper foot (I)-006905008
4
2
3. Buttonhole foot (D) -006102008
9
11
1
4. Cording foot (M) -006813008
6
5
17
5. Overcasting foot (E) -006907008
b
6. Blind hem foot (F) -006904008
22
20
14
7. Hemmer foot (K) -006900008
19
8. Satin stitch foot (A) -006172008
9. Quilting foot (P) -006916008
10.Darning/ Embroidery foot -006016008
c
11.Gathering foot -006917008
12.Button sewing foot -006914008
12
13.Brush/ Seam ripper -006099008
14.Spool holder (Large) -R12373210
16
21
10
13
13
8
15.Spool holder (Small) -TA10943209
15
18
16.Seam guide -006008001
17.Bobbin(3x) -006084009
18.Screwdriver (L & S) -006012008
19.Pack of needle -006014148
20.Spool pin felt -006015009
b
21.Second spool pin -R60033210
22.Twin needle -006020008
c
23
23.Walking foot -006185008
a
6
CONNECTING THE MACHINE TO THE POWER SOURCE
CONNECTING THE MACHINE TO THE POWER SOURCE
Caution: Always make sure that the machine is unplugged from power source and the main
switch is on "O". when the machine is not in use and before inserting or removing parts.
OFF
ON
Connecting the machine
Before connecting the power supply, make sure that the voltage and frequency shown on the
machine is conforming with your electrical power.
Place the machine on a stable table.
1. Connect the power line cord to the machine by inserting the 2-hole plug into the terminal box.
2. Connect the power line plug to the electric outlet.
3. Turn on the power switch.
4. The sewing lamp will light up when the switch is turned on.
To disconnect, turn the power switch to the off position, then remove plug from outlet.
Polarized plug information
This appliance has a polarized plug (one blade wider than the other),
to reduce the risk of electrical shock; this plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Do not
modify the plug in any way.
7
STARTING SEWING
STARTING SEWING
Start/stop button
The machine will start running when
Start/stop button is pressed and will stop
when pressed the second time.
The machine will rotate slowly at start of
sewing.
The speed limiting adjustment lever can
control the sewing speed. To increases
the speed, slide the lever to the right , To
decrease the sewing speed, slide the
lever to the left.
Foot control
With the sewing machine turned off,
insert the foot control plug into its
connector on the sewing machine.
Turn on the sewing machine, and then
slowly depress the foot control to start
sewing.
Release the foot control to stop the
sewing machine.
Please Note: The setting of the speed limiting adjustment lever will limit the maximum
speed of the machine.
Attention: Consult a qualified electrician if in doubt as how to connect the machine to
the power source. Unplug the power cord when the machine is not in use.
The appliance must be used with the foot controller C-9000 manufactured by CHIEN
HUNG TAIWAN., LTD.
8
ADJUSTING THE PRESSER FOOT PRESSURE
ADJUSTING THE PRESSER FOOT PRESSURE
The presser foot pressure dial is on the
left of the face plate.
The presser foot pressure of the
machine has been pre-set and requires
no particular readjustment according to
the type of fabric.
For sewing very thin fabric, loosen the
pressure by turning the screw
counterclockwise, and for heavy fabric,
tighten by turning it clockwise.
CHANGING THE PRESSER FOOT
CHANGING THE PRESSER FOOT
Attention: Turn power switch to off
("O") when carrying out any of the
above operations!
a
Attaching the presser foot holder (1)
b
d
1
b
Raise the presser foot bar (a). Attach the
presser foot holder (b) as illustrated.
c
Attaching the presser foot (2)
f
Lower the presser foot holder (b) until
the cut-out (c) is directly above the pin (d).
2
e
Raise the lever (e).
Lower the presser foot holder (b) and the
presser foot (f) will engage automatically.
g
Removing the presser foot (3)
Raise the presser foot.
Raise the lever (e) and the foot will
disengages.
Attaching the seam guide (4)
3
Attach the seam guide (g) in the slot as
illustrated. Adjust according to need for
hems, pleats, etc.
4
9
REPLACING THE NEEDLE
REPLACING THE NEEDLE
Attention: Turn power switch to off. ("O")
when carrying out any of the above
operations!
Change the needle regularly, especially if it is
showing signs of wear and causing problems.
B
A
Insert the needle following the illustrated
instructions.
A. Loosen the needle clamp screw and tighten
again after inserting the new needle.
The flat side of the shaft should be towards the
back.
B. Insert the needle as far up as it will go.
Needles must be in perfect condition.
Problems can occur with:
- Bent needles
- Blunt needles
- Damaged points
MATCHING NEEDLE/ FABRIC/ THREAD
MATCHING NEEDLE/ FABRIC/ THREAD
NEEDLE, FABRIC, THREAD SELECTION GUIDE
NEEDLE SIZE
FABRICS
THREAD
9-11 (70-80)
Lightweight fabrics-thin cottons, voile,
serge, silk, muslin, Qiana, interlocks,
cotton knits, tricot, jerseys, crepes,
woven polyester, shirt & blouse fabrics.
Light-duty thread in cotton, nylon,
polyester or cotton wrapped
polyester.
11-14 (80-90)
Medium weight fabrics-cotton, satin,
kettleclote, sailcloth, double knits,
lightweight woollens.
14 (90)
Medium weight fabrics-cotton duck,
woolen, heavier knits, terrycloth,
denims.
16 (100)
Heavyweight fabrics-canvas, woolens,
outdoor tent and quilted fabrics,
denims, upholstery material (light to
medium).
Most threads sold are medium
size and suitable for these
fabrics and needle sizes. Use
polyester threads on synthetic
materials and cotton on natural
woven fabrics for best results.
Always use the same thread on
top and bottom.
18 (110)
Heavy woollens, overcoat fabrics,
upholstery fabrics, some leathers
and vinyls.
Heavy duty thread, carpet thread.
Please Note:
- In general, fine threads and needles are used for sewing fine fabrics, and thicker threads
are used for sewing heavy fabrics.
- Always test thread and needle size on a small piece of fabric which will be used for actual
sewing.
- Use the same thread for needle and bobbin.
10
TYPE OF PRESSER FOOT CHART
TYPE OF PRESSER FOOT CHART
(Double needle is being suggested for certain stitches for more creativity)
PRESSER FOOT
APPLICATION
General sewing,
Patchwork stitches,
Decorative
stitching,
Smocking,
All purpose foot (T)
Fagoting, etc.
NEEDLE
PRESSER FOOT
APPLICATION
Satin stitch
Satin stitch foot (A)
Quilting
Inserting zippers
Zipper foot (I)
Quilting foot (P)
Buttonhole
Darning
Free embroidery
Monogramming
Darning/
Embroidery foot
Buttonhole foot
(D)
Gathering
Cording
Cording foot (M)
Gathering foot
Button sewing
Overcasting
Button sewing foot
Overcasting foot
(E)
This foot helps to
prevent uneven
feeding of very
difficult fabrics
Blind hem
Blind hem foot (F)
Walking foot
Narrow hemming
Hemmer foot (K)
11
NEEDLE
WINDING THE BOBBIN
WINDING THE BOBBIN
2
1
3
5
4
3
4
11
Bobbin winding
1. Place the thread and spool holder onto the spool pin.
For smaller spools of thread, place spool holder with
the small side next to the spool or use the small spool
holder.
1
2. Snap the thread into the thread guide (Child beneath
thread guide cover).
4
2
3. Wind the thread clockwise around the bobbin winder
tension discs.
3
4. Place the thread end through one of the inner holes in
the bobbin as illustrated and place empty bobbin on
the spindle.
4
5. Press the bobbin winder stopper against the bobbin.
5
12
WINDING THE BOBBIN
WINDING THE BOBBIN
6. When the bobbin winder switch is pressed to the left,
LCD will display the animation of bobbin winding,
press the engaging lever to right, the animation
disappear, LCD display the frame of ordinary
operating.
6
7. Hold the thread tail securely in one hand.
7
8. Press the Start/stop button or foot control.
8
9. After the bobbin has wound a few turns stop the
machine and cut the thread near the hole of the
bobbin. Set the speed to maximum. Continue filling
the bobbin until it is full. The motor stops automatically
when the bobbin is full.
9
10.Stop the machine, cut the thread and then remove the
bobbin.
10
Please Note: When the bobbin winder switch is placed on the left, "bobbin winding
position", the machine will not sew and the handwheel will not turn. To start sewing, push
the bobbin winder switch to the right "sewing position".
13
INSERTING THE BOBBIN
INSERTING THE BOBBIN
Attention: Turn power switch to off ("O")
before inserting or removing the bobbin.
When inserting or removing the bobbin,
the needle must be fully raised.
1. Insert the bobbin in the bobbin case with
the thread running in a counterclockwise
direction (arrow).
1
2. Pull the thread through the slit (A).
A
2
3. Pull the thread toward the left and along
the inside of the spring until it slips into
the notch (B) being sure that the thread
does not slip out of the slit (A).
B
3
A
B
4. Pull out about 15 cm (6 inches) of thread
and attach the bobbin cover plate. (C)
C
4
14
THREADING THE UPPER THREAD
THREADING THE UPPER THREAD
3
2
5
1
3
4
6
5
7
8
Please Note: It is important to carry out the threading correctly as by not doing so several
sewing problems could result.
Start by raising the needle to its highest point, and
also raise the presser foot to release the tension
discs.
1. Lift up the spool pin. Place the spool of thread on the
spool pin so that the thread comes from the front of the
spool, then place the spool cap at the end of the spool pin.
1
2. Draw the thread from the spool through the upper
thread guide.
4
2
3. Guide the thread around the thread guide pulling the
thread through the pre-tension spring as illustrated.
4
3
15
THREADING THE UPPER THREAD
THREADING THE UPPER THREAD
4. Thread the tension module by passing the thread
between the silver discs.
4
5. Then, down and around the check spring holder.
5
6. At the top of this movement, pass the thread from right
to the left through the slotted eye of the take-up lever
and then downwards again.
6
7. Pass the thread behind the flat, horizontal thread guide.
7
8. Guide the thread through the wire loop.
8
9. Pull the end of the thread through the needle from front
to rear, and pull out about 10 cm of thread.
Use the needle threader to thread the needle. (On the
next page.)
9
16
USING THE NEEDLE THREADER
USING THE NEEDLE THREADER
Attention: Turn power switch to the off
position ("O").
Raise the needle to its highest position
and lower the presser foot.
1. Lower the needle threader lever slowly
and draw the thread through the thread
guide as illustrated and then to the right.
1
2. The needle threader automatically turns
to the threading position and the hook pin
passes through the needle eye.
2
3. Take the thread in front of the needle.
3
4. Hold the thread loosely and release the
lever slowly. The hook will turn and pass
the thread through the needle eye forming
a loop.
Pull the thread through the needle eye.
4
17
THREAD TENSION
THREAD TENSION
Loose
Tight
- Basic thread tension setting: "4"
- To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial
to the next number down.
- Proper setting of tension is important to good sewing.
- There is no single tension setting appropriate for all the stitch functions and fabrics.
- 90% of all sewing will be between "3" and "5" ("4" is basic setting).
- For all decorative sewing you will always obtain a nicer stitch and less fabric puckering when the
upper thread appears on the bottom side of your fabric.
Surface
1.Normal thread tension for straight stitch
sewing.
Surface
2. Thread tension is too loose for straight
stitch sewing. Turn dial to higher number.
Surface
3. Thread tension is too tight for straight stitch
sewing. Turn dial to lower number.
Surface
4. Normal thread tension for zig zag and
decorative sewing.
Reverse
side
Upper thread
1
Bobbin thread
Reverse
side
Upper thread
2
Bobbin thread
Reverse
side
Upper thread
3
Bobbin thread
Reverse
side
Upper thread
4
Bobbin thread
18
RAISING UP THE LOWER THREAD
RAISING UP THE LOWER THREAD
1. Hold the upper thread with the left
hand. Turn the handwheel towards
you (counterclockwise) lowering, then
raising the needle.
1
2. Gently pull on the upper thread to
bring the bobbin thread up through the
needle plate hole. The bobbin thread
will come up in a loop.
2
3. Pull both threads to the back under the
presser foot.
3
CUTTING THE THREAD
CUTTING THE THREAD
Raise the presser foot. Remove the
fabric, draw the threads to the left side of
the face cover and cut using the thread
cutter.
The threads are cut at the proper length
to start the next seam.
19
TWO-STEP PRESSER FOOT LIFTER
TWO-STEP PRESSER FOOT LIFTER
1. The presser foot lifter raises and
lowers your presser foot.
1
2. When sewing several layers or thick
fabrics, the presser foot can be raised
a second stage for easy positioning of
the work.
2
TO RAISE OR DROP THE FEED DOGS
TO RAISE OR DROP THE FEED DOGS
With the sewing table off the machine,
the feed dog adjustment lever can be
seen on the base in back of the sewing
machine.
Sliding the lever to the "
" (b) will lower
the feed dog, for example during button
sewing. If you wish to continue sewing
normally, slide the lever to the "
" (a) in
order to raise the feed dogs.
a
b
a
The feed dog will not rise up if you do not
turn the handwheel, even if the lever is
slid to the right. Make a complete turn to
raise the feed dogs.
b
20
OPERATION BUTTONS
OPERATION BUTTONS
Needle up/down
position button
Auto-lock button
Reverse button
Start/stop button
Start/stop button
The machine will start running when start/stop
button is pressed and will stop when pressed the
second time. The machine will rotate slowly at the
beginning of the sewing.
The sewing speed can be controlled by the speed
limiting adjustment lever.
Reverse button
When the patterns 00-05, 30-99 are selected, the
machine will sew in reverse or a reinforcement
stitch at a low speed if the reverse button is
pressed. The machine will sew forward after the
button is released.
An arrow " " on the LCD display indicates reverse
sewing.
21
OPERATION BUTTONS
OPERATION BUTTONS
Auto-lock button
When the patterns 00-06 are selected, the machine
will immediately sew 3 locking stitches when the
Auto-lock button is pressed, then automatically stop.
The LCD will display the figure " " until the
machine is stopped.
When the patterns 07-15, 30-99 are selected,
press the Auto-lock button, the machine will sew 3
locking stitches at the end of the current pattern
and automatically stop. The LCD will display the
figure " " until the machine is stopped.
The function will be cancelled if you press the
button once again or select another pattern.
Needle up/ down position button
With the Needle up/ down position button, you
decide whether the needle shall stop in the up
position or in the material when you stop sewing.
Press the button so that the arrow, on the LCD
screen, will point upward " " and the needle will
stop in the highest position. When you press the
button so that the arrow points downward "
",
the machine will stop with the needle in the
lowest position.
22
FUNCTION BUTTONS
FUNCTION BUTTONS
Mode selection button
Elongation button
Mirror button
Twin needle button
Stitch length
adjustment button
Stitch width
adjustment button
Stitch width adjustment button
When you select a stitch, the machine will
automatically set the recommended stitch width,
which will be indicated by numbers on the LCD
screen. The stitch width can be regulated by
pressing the stitch width adjustment buttons.
Certain stitches have a limited stitch width.
For a narrower stitch, press the " " button (left).
For a wider stitch, press the "+" button (right). The
stitch width can be adjusted between "0.0-7.0".
Certain stitches have a limited stitch width.
When patterns 00~04 are selected, the needle
position is regulated by the stitch width
adjustment buttons. Pressing the " " button (left),
will move the needle to the left and pressing the
"+" button (right), will move the needle to the right.
The numbers will be changed from left position
"0.0" to extreme right position "7.0". The pre-set
center needle position will be indicated as "3.5".
23
FUNCTION BUTTONS
FUNCTION BUTTONS
Stitch length adjustment button
When you select a stitch the machine will
automatically set the recommended stitch length
which will be indicated by numbers on the LCD
screen. The stitch length can be adjusted by
pressing the stitch length adjustment buttons.
To shorten the stitch length, press the " "
button (left). For a longer stitch length, press the
"..." button (right). The stitch length can be
adjusted between "0.0-4.5". Certain stitches have
a limited length.
MODE selection button
The LED light will be set at direct mode " " when
start the machine. By pressing the button, LED
light will move step by step to select the stitch
mode, as shown.
Direct mode stitch selection.
MODE
Utility and decorative pattern mode: Stitch
selection using number buttons.
A
A Block letter mode: Character selection using
number buttons.
A
A
Script letter mode: Character selection using
number buttons.
Outline letter mode: Character selection
using number buttons.
Elongation button (see page 56)
The pattern 30-39 can be elongated up to five
times its normal length by pressing the "
"
button, LED light will turn on.
When the width or length or stitch is changed, a
greater variety of patterns are available.
24
FUNCTION BUTTONS
FUNCTION BUTTONS
Mirror button (see page 57)
The patterns 00-15, 30-99 can be mirror imaged
along a vertical axis by pressing the " " button,
LED light will turn on. The machine will continue
to sew the reflected pattern until the mirror button
is pressed again. The mirror function also will be
canceled if the pattern changed.
The function for mirror imaging the pattern appears
on the LCD screen.
Twin needle button (see page 58)
With the twin needle, the patterns 00-15, 30-99
can sew two parallel lines of the same stitch with
two different threads.
Press the " " button, LED light will turn on, and
the machine automatically reduces the maximum
width for twin needle sewing. Press the button
again for single needle sewing.
25
SELECTION BUTTONS
SELECTION BUTTONS
Direct pattern selection
and number buttons
Clear button
Edit button
Memory button
Direct pattern selection and number buttons
1
2
3
4
5
6
7
8
9
Direct pattern selection
Press the buttons to select the utility patterns
shown beside the number button when the mode
button is set at the Direct mode.
0
Number buttons
Press the number buttons of the pattern number
to select the desired pattern.
Except the Direct Pattern mode, the other mode
can be selected by pressing the desired numbers.
Example: pattern 36
26
SELECTION BUTTONS
SELECTION BUTTONS
Clear button
1
2
3
4
5
6
7
8
9
Press this button when the incorrect character is
selected. Each press of this button erases one
character, or press this button to remove an
added pattern when sewing combinations of
characters or decorative stitches.
0
Edit button
1
2
3
4
5
6
7
8
9
0
If you wish to modify any settings in the memory
mode, use the stitch width "+" or "-" button to
select the pattern to be modified, and press the
"123" button to set the selected pattern under the
editing mode, the LED light will turn on. Manual
setting function of the stitch width, stitch length,
mirror and auto-lock for these memorized
patterns is now possible. Press the "
" button
again to leave the editing mode and return to
memory mode.
Memory button
1
2
3
4
5
6
7
8
9
Press the " " button to enter the memory mode,
and store the combinations of characters or
decorative stitches. Use the stitch width " + " or
"...." button to confirm the pattern memorized by
pressing this button in memory mode.
Please Note: The Direct mode patterns and
buttonholes cannot be memorized.
0
27
USEFUL SKILLS
USEFUL SKILLS
Sewing corners
1. Stop the sewing machine
when you reach a corner.
2
1
5
3
2. Lower the needle into the
fabric manually or by pressing
the needle up/down button
once.
3. Raise the presser foot.
4
4. Use the needle as a pivot
and turn the fabric.
5. Lower the presser foot and
resume sewing.
Reverse
Reverse stitching is used to
secure the threads at the
beginning and at the end of a
seam.
Press the reverse button and
sew 4-5 stitches.
The machine will sew forward
when the button is released.
Free arm
Free-arm sewing is convenient for sewing tubular areas such as pant hems and cuffs.
28
USEFUL SKILLS
USEFUL SKILLS
Sewing on the heavy fabric
The black button on the right
side of the presser foot will lock
the presser foot in a horizontal
position if you push it in before
lowering the presser foot. This
ensures even feeding at the
beginning of a seam and helps
when sewing multiple layers of
fabric such as sewing over
seams when hemming jeans.
When you reach the point of an
increased thickness, lower the
needle and raise the presser
foot. Press the toe of the foot
and push in the black button,
then lower the foot and
continue sewing.
Cardboard or
thick fabric
The black button releases
automatically after sewing few
stitches.
You also can place another
piece of fabric with the same
thickness at the back of the
seam. Or support the presser
foot while feeding by hand and
sewing toward the folded side.
29
STRAIGHT STITCHES AND NEEDLE POSITION
STRAIGHT STITCHES AND NEEDLE POSITION
T
Changing the needle position
0.0
2.0
3.5
5.0
7.0
These setting apply only to pattern 00-04. The pre-set
position is "3.5", center position. When you press the
"..." stitch width adjustment button, the needle position
will move to the left. When you press the "+" stitch
width adjustment button, the needle position will move
to the right. On the LCD screen, the point illustration
and the number indicate the needle position.
Changing the stitch length
To shorten the stitch length, press the " " stitch length
adjustment button. For a longer stitch length, press the
"+" stitch length adjustment button.
0.5
1.0
3.0
2.0
4.5
Generally speaking, the thicker the fabric, thread and
needle, the longer the stitch should be.
ZIGZAG STITCHES
ZIGZAG STITCHES
A
T
Adjusting the stitch width
The maximum zigzag stitch width for zigzag stitching is
"7.0"; however, the width can be reduced on any
patterns. The width increases as you press the "+"
stitch width adjustment button from "0.0-7.0".
0.0
1.0
3.0
5.0
7.0
Adjusting the stitch length
The density of zigzag stitches increase as the setting
of stitch length approaches "0.2".
Neat zigzag stitches are usually achieved at "1.0-2.5".
0.5
1.0
2.0
3.0
4.5
Closed up zigzag stitches (close together) are referred
to as a satin stitch.
30
STRETCH STITCH
STRETCH STITCH
A
T
It assures you of a stitch that is strong and
flexible and will give with the fabric without
breaking. Good for easy to ravel and knit
fabrics. It is good for joining durable fabric
such as denims.
Straight stretch stitch
These stitches can also be used as a
decorative top stitch.
Straight stitch
Straight stretch stitch is used to add triple
reinforcement to stretch and hardwearing
seams.
Triple zigzag stretch stitch is suitable for
firm fabrics like denim, poplin, duck, etc.
31
OVERCASTING STITCHES
OVERCASTING STITCHES
Using the overcasting foot
E
1
5.0~7.0
2.0~3.0
3
2
1. Change the presser foot to the overcasting foot.
2. Sew the fabric with the fabric edge against the guide of the overcasting foot.
Attention: The overcasting foot should be used to sew with patterns 05 and 08 only and do
not set the stitch width narrower than "5.0". It is possible that needle could hit the presser
foot and break when sewing other patterns and width.
Using the all purpose foot
1
T
2.5~4.5
2.0~3.0
2
3
1. Change the presser foot to the all purpose foot.
2. Sewing the overcasting along the edge of the fabric so that the needle drops over the edge of
the fabric on the right side.
32
BLIND HEM/ LINGERIE STITCH
BLIND HEM/ LINGERIE STITCH
10: Blind hem/lingerie for firm fabrics
F
2.5~4.0
5mm
1.0~2.0
11: Blind hem for stretch fabrics
Please Note: It takes practice to sew
blind hems. Always make a sewing
test first.
5mm
1. Fold the fabric as illustrated with the
wrong side uppermost.
1
Reverse Overcasting
side
stitches
Reverse
side
a
2
3
2. Place the fabric under the foot. Turn the
handwheel forwards by hand until the
needle swings fully to the left. It should
just pierce the fold of the fabric. If it does
not, adjust the stitch width accordingly.
3. Adjust the guide (b) by turning the knob (a)
so that the guide just rests against the fold.
b
4. Sew slowly, guiding the fabric carefully
along the edge of the guide.
4
5. Turn over the fabric.
5
33
BUTTON SEWING
BUTTON SEWING
2.0~7.0
Change the presser foot to the button sewing
foot.
1. Move the drop feed control to "......." to
lower the feed dogs.
a
1
b
a
b
2. Position the work under the foot. Place the
button in the desired position, lower the
foot.
3
3. Select zig zag pattern. Adjust the stitch
width to "2.0-7.0" according to the distance
between the two holes of the button.
2.0~7.0
4. Turn the handwheel to check that the
needle goes cleanly into the left and right
holes of the button.
2
4
5. Before sewing, press the Auto-lock button
to sew reinforcement stitches automatically
at the beginning and at the end of the stitch.
If a shank is required, place a darning
needle on top of the button and sew.
5
6 For buttons with 4 holes, sew through the
front two holes first, push work forward and
then sew through the back two holes.
6
34
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
16: For thin or medium fabric
D
17: For horizontal holes on blouses
or shirts made from thin or
medium fabric
2.5~7.0
0.3~1.0
3.0~7.0
0.3~1.0
19: For horizontal holes on blouses
or shirts made from thin or
medium fabric
2.5~5.5
0.3~1.0
20: For horizontal buttonholes on
thick fabrics
18: For thin or medium fabric
21: For thin or medium fabric
5.5~7.0
0.3~1.0
22: For suits or overcoats
23: For thick coats
24: For jeans or trousers
3.0~7.0
1.0~2.0
25: For jeans or stretch fabric with
a coarse weave
26: For stretch fabric
3.0~7.0
1.0~3.0
Please Note: Before sewing a buttonhole on your project, practice on a scrap piece of the
same type of fabric.
1. Mark the positions of the buttonhole on the
fabric.
The maximum buttonhole length is 3cm (1
3/16 inch). (Total of diameter + thickness of
button.)
1
2. Attach the buttonhole foot, then pull out the
button holder plate and insert the button.
The size of the buttonhole is determined by
the button inserted in the button plate.
The thread should be passed through the
hole in the presser foot, then be placed
under the foot.
2
35
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
3. Select the buttonhole stitch. Adjust the
stitch width and the stitch length to the
desired width and density.
NOTE
Make no
gap here
3
Starting
point
4. Position the fabric under the presser foot
so that the centerline's mark is aligning with
the center of the buttonhole foot.
Lower the buttonhole lever, then push it to
the back.
H
PUS
H
PUS
4
Please Note: When you select any
buttonhole pattern, LCD screen will be
demonstrated the warning animation
message display, it is to remind you to
lower the buttonhole lever.
5. While lightly holding the end of upper
thread and start sewing.
PUS
Please Note: Gently feed the fabric by
hand. Before stopping, the machine will
automatically sew a reinforcement
stitch after the buttonhole is sewn.
H
5
36
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
6
6. Buttonholes are sewn from the front of the
presser foot to the back, as shown.
7. Raise the presser foot and cut thread. To
sew over same buttonhole, raise the presser
foot (will return to original position). After
sewing the buttonhole stitch, raise the
buttonhole lever until it stops.
H
PUS
7
Please Note: After finishing the
buttonhole stitch, LCD screen will be
demonstrated the warning animation
message display, it is to remind you to
lift the buttonhole lever.
37
BUTTONHOLE STITCHING
BUTTONHOLE STITCHING
8. Cut the center of the buttonhole being
careful not to cut any stitches on either side.
Use a pin as a stopper at the bartack so
you do not cut too much.
8
Making a buttonhole on stretch fabrics
When sewing buttonholes on stretch fabric, hook heavy thread or cord under the
buttonhole foot.
1. Attach the buttonhole foot and hook the
gimp thread onto the back of the presser
foot. Bring the two gimp thread ends to the
front of the foot and insert them into the
grooves, then temporarily tie them there.
Lower the presser foot and start sewing.
Set the stitch width to match the diameter
of the gimp thread.
NOTE
Make no
gap here
1
2. Once sewing is completed, pull the gimp
thread gently to remove any slack, then
trim off any excess.
2
Please Note: It is suggested that you use interfacing on the backside of the fabric.
38
ADJUSTING
ADJUSTINGPATTERN
PATTERNBALANCE
BALANCE
If the decorative stitch patterns, numbers or manual buttonhole stitch are uneven when
you sew on a particular fabric, adjust them with the feed balancing dial.
The dial should usually be in a neutral
position.
Adjusting distorted stretch stitch patterns
A
B
A. When Patterns are too compressed, correct
by turning the dial in the direction of "–".
C
B. Correct setting.
C. When Patterns are too drawn out, correct
by turning the dial in the direction of "+".
Adjusting distorted letters or numbers
A
B
A. When the letters or numbers overlap, turn
the dial to "–".
C
B. Correct setting.
C. When the patterns are too drawn out,
correct by turn the dial to "+".
Adjusting the stitch density for buttonhole
A
B
A. Right side is denser. If the left side of the
buttonhole is less dense than the right side,
turn the feed balancing dial to "–".
C
B. Correct setting.
C. Left side is denser. If the right side of the
buttonhole is less dense than the left side,
turn the feed balancing dial to "+".
39
EYELET STITCH
EYELET STITCH
A
27: Select for sewing eyelets on belts , etc
5.0 6.0 7.0
1. Select pattern 27 to get the eyelet stitch.
Attach presser foot "A".
1
2. Press the " " or "+" stitch width adjustment
to button select the eyelet size.
Size of eyelet.
A
B
C
A. Large: 7.0mm (1/4 inch).
B. Medium: 6.0mm (15/64 inch).
C. Small: 5.0mm (3/16 inch).
2
3. Lower the needle into the fabric at the
beginning of the stitching, and then lower
the presser foot lever. Once sewing is
completed, the machine automatically
sews reinforcement stitches, then stops.
3
4. Make a hole at the center using an eyelet
punch.
* Eyelet punch is not included with the
machine.
Please Note: If thin thread is used, the
stitching may be coarse. If this occurs,
sew the eyelet twice one on top of the
other.
4
40
DARNING STITCH
DARNING STITCH
3.5~7.0
D
1.0~2.0
1. Select pattern 28 or 29 from the Group
Patterns "A" to get the darning stitch.
Change the presser foot to the buttonhole
foot.
1
2. Baste the upper fabric and the under fabric
together. Select the needle position. Lower
the presser foot over the center of the tear.
NOTE
Make no
gap here
2
3. Pull the button holder to the rear. Set the
button guide plate on buttonhole foot to the
desired length.
3
Stop
a
Start
4. The size of one darn cycle is variable.
However, the maximum stitch length is
2.6cm (1 inch) and the maximum stitch
width is 7mm (9/32 inch).
Stop
a
b
Start
b
NOTE
Make no
gap here
a. The length of sewing.
4
b. The width of sewing.
41
DARNING STITCH
DARNING STITCH
5. Position the fabric so that the needle is
2mm (1/16 inch) in front of the area to be
darned, and then lower the presser foot
lever.
Please Note: When lowering the
presser foot, do not push in the front of
the presser foot, otherwise the darning
will not be sewn with the correct size.
2mm
5
6. Pass the upper thread down through the
hole in the presser foot. Pull down the
buttonhole lever then push it back. The
buttonhole lever is positioned behind the
bracket on the buttonhole foot. Gently hold
the end of the upper thread in your left
hand, and then start sewing.
H
PUS
Please Note: When you select any
buttonhole pattern or darning pattern,
LCD screen will be demonstrated the
warning animation message display, it
is to remind you to lower the buttonhole
lever.
6
7. Darning stitches are sewn from the front of
the presser foot to the back, as shown.
7
8. If the sewing range is too big to sew, then
we suggest you can sew several times (or
cross sew) to get better sewing result.
8
42
ZIPPER INSERTION
ZIPPER INSERTION
3.5
I
Attention: Zipper foot should be used for
sewing width center needle position
straight stitch only. It is possible that
needle could hit the presser foot and
break when sewing other patterns.
1.5~3.0
Inserting a centered zipper
1. Baste the zipper opening on the garment.
2 inch
2. Press open the seam allowance. Place the
zipper face down on the seam allowance
with the teeth against the seam line. Baste
the zipper tape.
1
2
3. Attach the zipper foot. Attach the right side
of the presser foot pin to the holder when
sewing the left side of the zipper.
4. Attach the left side of the presser foot pin to
the presser foot holder when sewing the
right side of the zipper.
3
4
5. Stitch left side of the zipper from top to
bottom.
6. Stitch across the lower end and right side
of zipper. Remove the basting and press.
5
6
43
ZIPPER INSERTION
ZIPPER INSERTION
Inserting a side zipper
1. Baste the zipper opening on the garment.
2 inch
2. Fold back to the left seam allowance. Turn
under the right seam allowance to form
3mm (1/8 inch) fold.
1
2
3. Attach the zipper foot. Attach the right side
of the presser foot pin to the holder when
sewing the left side of the zipper. Attach
the left side of the presser foot pin to the
presser foot holder when sewing the right
side of the zipper.
4. Stitch the left side of zipper from bottom to
top.
3
4
5. Turn the fabric right side out, stitch across
the lower end and right side of zipper.
6. Stop about 5cm (2 inches) from the top of
zipper. Remove the basting and open the
zipper. Stitch the remainder of the seam.
5
6
44
NARROW HEMMING
NARROW HEMMING
K
3.5
1.5~3.0
1. Fold edge of fabric over about 3mm (1/8
inch), then fold it over again 3mm (1/8 inch)
for about 5cm (2 inches) along the edge of
the fabric.
1
2. Insert the needle into the fold by rotating
the handwheel toward you, and lower the
presser foot. Sew several stitches and
raise the presser foot.
Insert the fabric fold into the spiral opening
of hemmer foot. Move fabric back and forth
until the fold forms a scroll shape.
2
3. Lower the presser foot and start sewing
slowly guiding the raw edge of the fabric in
front of the hemmer foot evenly into the
scroll of the foot.
3
45
CORDING
CORDING
Sew over one strand of cording to create a pretty swirled design on a jacket or vest or sew over
three strands of cording for border trims. Pearl cotton, knitting yarn, embroidery floss, lace thread,
fine wool or lily yarn can be used for cording.
Single cording
M
Mark the design on the fabric. Insert the cord
in the center groove of the cording foot from
the right side opening. Pull the cord about
5cm (2 inches) behind the foot.
The grooves under the foot will hold the
length of the cord in place while the stitches
are being form over the cord.
Select the stitch and adjust the stitch width so
that the stitches are just covering the cord.
Lower the foot and sew slowly, guiding the
cord over the design.
Triple cording
M
Push the sewing thread to the left and insert
three cords into the grooves of the foot and
pull about 5cm (2 inches) of the cords behind
the foot. Select the desired pattern and adjust
the stitch width so that the stitches are just
covering the cords. Lower the foot and sew
slowly guiding the cords.
46
SATIN STITCH SEWING
SATIN STITCH SEWING
A
3.5~7.0
0.5~2.0
Use the satin stitch foot for satin stitching and
sewing decorative stitches. This foot has a full
indentation on the underside to allowed easy
sewing over the thickness of the stitches form
by closely spaced zigzag stitches, and even
feeding of the fabric.
To tailor the satin or decorative stitch pattern,
you may adjust the length and width of the
pattern by pressing the stitch length and width
adjustment buttons. Experiment with fabric
scraps until you get the desired length and
width.
05
37
30
38
31
39
32
33
40
34
41
35
42
Please Note: When sewing very thin
fabrics, it is suggested that you use
interfacing on the backside of the fabric.
36
43
47
QUILTING
QUILTING
3.5
P
1.0~3.0
Insert the quilting guide in the presser foot
holder as illustrated and set the space as you
desire.
Sew the first row and move over the fabric to
sew successive rows with the guide riding
along the previous row of stitching.
48
GATHERING
GATHERING
3.5
4.5
1. Remove the presser foot holder and attach
the gathering foot.
2. Sew a single row or multiple rows of
straight stitches.
3. If more gathering is required, loosen the
upper thread tension to below 2 so that the
bobbin thread lies on the underside of the
material.
4. Pull the bobbin threads to obtain the
desired amount of gather, then tie the
threads to secure them.
5. Smooth the gathers by ironing them.
Please Note: It can also use the all
purpose foot and gather fabric by hand
by lowering the tension setting to below
2 and pulling the lower thread to gather
the material.
49
SMOCKING
SMOCKING
T
A
1. Use the gathering foot to sew straight lines
1cm (3/8 inch) apart, across the area to be
smocked.
* For gathering sewing instructions, see
page 49.
1
2. Knot the threads along one edge. Pull the
bobbin threads and distribute the gathers
evenly. Secure the threads at the other end.
2
3. Reduce the tension, if necessary and sew
decorative pattern stitches between the
straight seams.
3
4. Pull out the gathering stitches.
4
50
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
3.5~5.0
Move the drop feed control to "
the feed dogs.
" to lower
a
b
a
b
Remove the presser foot holder, and attach
the darning foot to the presser foot holder bar.
The lever (a) should be behind the needle
clamp screw (b). Press the darning foot on
firmly from behind with your index finger and
tighten the screw (c).
a
b
c
Darning
Please Note: Free motion darning is accomplished without the sewing machine internal
feed system. Movement of the fabric is controlled by the operator. It is necessary to
coordinate sewing speed and movement of fabric.
First sew around the edges of the hole (to
secure the threads). Working from left to right,
sew over the hole in a constant and
continuous movement. Turn the work by 1/4
and sew over the first stitching moving the
work slower over the hole to separate the
threads and not form big gaps between the
threads.
51
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING
Embroidery
Select zigzag stitch pattern and adjust the
stitch width as desired. Stitch along the
outline of the design by moving the
embroidery hoop. Make sure to maintain a
constant speed.
Fill in the design working from the outline
towards the inside. Keep the stitches close
together.
You will get longer stitches by moving the
hoop faster and shorter stitches by moving
the hoop more slowly.
Secure with a reinforcement stitches at the
end by press Auto-lock button.
Monogramming
Select the zigzag stitch pattern and adjust the
stitch width as desired. Sew at a constant
speed, moving the hoop slowly along the
lettering.
When the letter is finished. Secure with a
reinforcement stitches at the end by press
Auto-lock button.
* Embroider hoop is not included with the machine.
52
WALKING
WALKINGFOOT
FOOT
Please Note: Always try to sew first without the walking foot
accessory which should be used only when necessary.
It is easier to guide the fabric and you have a
better view of the seam when using the
standard, regular foot on your machine. Your
sewing machine offers excellent stitch quality
on a wide range of fabrics from delicate
chiffons to multiple layers of denim.
1
The Walking Foot accessory equalizes the
feeding of the upper and lower layers of fabric
and improves the matching of plaids, stripes
and patterns. It also helps to prevent uneven
feeding of very difficult fabrics.
1. Lift the presser foot lifter to raise the
presser foot bar.
2
2. Remove the presser foot holder by
unscrewing (counterclockwise) the presser
bar attaching screw.
a
b
3. Attach the Walking Foot to the machine as
follows:
- The arm (a) should fit into above the
needle screw and clamp (b).
c
- Slide the plastic attaching head (c) from
your left to right so that it is fitted into the
presser foot bar.
3
- Lower the presser foot bar.
- Replace and tighten (clockwise) the
presser bar attaching screw.
- Make sure both the needle screw and the
presser bar attaching screw are tightly
secured.
4. Draw the bobbin thread up and place both
the bobbin thread and the needle thread
behind the walking foot attachment.
4
53
FAGOTING
FAGOTING
A
T
1. Separate the folded edges of the fabric
pieces with a gap of 4mm (1/8 inch) and
baste them onto a piece of thin paper or
water-soluble stabilizer sheet.
Thin paper
Basting
1
2. Align the center of the presser foot with the
center of the two pieces of fabric and begin
sewing.
3. After sewing, remove the paper.
3
2
PATCHWORK STITCHING
PATCHWORK STITCHING
A
T
1. Place the two pieces of fabric with the right
side together and sew with the straight
stitch.
2. Open the seam allowances and presses it
flat.
1
2
3. Place the center of the presser foot on the
seam line of the joined pieces of fabric and
sew over the seam.
3
54
SCALLOP
SCALLOPSTITCH
STITCH
Scallop hem
T
1. Fold the fabric right side together in and
sew along the edge.
2. Cut the fabric along the seam leaving an
allowance of 3mm (1/8 inch) for seaming.
Notch the allowance.
1
Wrong side
of fabric
2
3. Turn fabric over and push out the curved
seam to the surface and iron it.
3
Scallop edging
A
T
1. Sew on hem line.
2. Trim the fabric close to the stitching taking
care not to cut the thread.
1
2
55
ELONGATION
ELONGATION
A
2.5~7.0
0.3~1.0
1. The stitch can be elongated up to five times
its normal length by pressing the elongation
button.
1
2. The LCD screen icon for elongation imaging
of the pattern appears.
2
3. When the width or length or stitch is
changed, a greater variety of patterns are
available.
x1
x2
Please Note: The patterns 30-39 can
be elongation and mirror simultaneously.
x3
x4
3
x5
56
MIRROR
MIRROR
Please Note:
- Pattern 16-29 cannot be mirror imaged.
- Mirror imaged patterns can also be combined with other patterns.
1. Select the pattern.
1
2. Pressing the mirror button.
2
3. The LCD screen icon for mirror imaging of
the pattern appears.
3
A. Normal pattern sewing.
B. Mirror pattern sewing.
A
B
4
57
USING
USINGTHE
THETWIN
TWINNEEDLE
NEEDLE
Please Note: When using twin needles, use the "T" presser
foot regardless of what kind of sewing will be carried out.
1.0~3.0
T
1. Insert the twin needle.
Attention: Only use the twin needle
(part code: 006020008). Use of any
other needle may bend the needle or
damage the machine. Never use bent
needles. Bent needles can easily break,
possibly resulting in injuries.
1
2. Follow the instructions for single-needle
threading using the horizontal spool pin.
Thread through the left needle.
5
Set the second spool pin (included with the
accessories) into the hole on the top of the
machine. Thread through remaining points,
making certain to omit the thread guide
above the needle and pass thread through
the right needle.
3
2
3. Thread each needle separately.
Please Note: Make sure that the two
threads used to thread the twin needle
are of the same weight. You can use
one or two colors.
3
4. Press the Twin needle button, LED light will
turn on, and the machine automatically
reduces the maximum width for twin needle
sewing.
4
5. Select a stitch pattern and start to sewing.
The patterns 00-15, 30-99 can be used.
Two lines of stitching are sewn parallel to
each other.
Please Note: When sewing with twin
needle, always proceed slowly, and
make sure to maintain a low speed to
insure quality stitching.
5
58
MEMORY
MEMORY
Combined patterns can be stored for later use. Since stored patterns are not lost after the
sewing machine is turned off, they can be recalled at any time. This is convenient for
patterns, such as names, that will be used often.
Please Note:
- Multiple patterns selecting from pattern modes
sewn together.
,
A
,
,
A
can be combined and
- This machine has 4 modules of program memory and each module can retain 20 units of
stitches.
- Patterns 16-29 cannot be entered into memory.
- All the units in the memory can be edited to set its function such as Stitch length, Stitch
width, Elongation, Mirror, and Auto-lock.
Combining patterns or letters
1. Press "MODE" button to select any desired pattern group
among
,A,
,
on front cover.
A
MODE
The LED will indicate the selected group.
A
1
A
2. Press the " " button to open the memory mode and then
appears a sub-screen in the center. It is available to select
the number of the memory module when the cursor start
flashing.
2
3. Press number of memory module. (e.g. 2)
3
4. Enter the memory screen automatically and the flashing
cursor stays in the first position.
4
59
MEMORY
MEMORY
5. Press the desired pattern number. (E.g.68)
5
6. The selected pattern displays on the LCD screen and the
cursor move to the next position.
6
7. Repeat step 5, 6 for more patterns to be stored in the
memory.
7
Please Note: When the memory the full with 20 units of
patterns, the machine will beep to signal it.
7
8. Press the " " button to leave the memory mode and return
to the normal screen.
Attention: The selected pattern will be cleared from the
memory module after closing the machine if you do not
press the "
" button again when you have completed
your selection.
8
Adding patterns or letters
1. Press the stitch width adjustment button and shift the cursor
past the last pattern or letter where you would like to add
another pattern while in the memory mode.
1
2. Press pattern number. (e.g. 31) The selected pattern will be
inserted.
2
60
MEMORY
MEMORY
Editing patterns
1. Use the stitch width adjustment button to select the pattern
that you wish to edit while in the memory mode.
1
2. Press the "
" button to edit the pattern. The stitch length,
stitch width, Elongation, Mirror, and Auto-lock of the
patterns can be adjusted manually.
2
Please Note: The stitch length, stitch width, Elongation,
Mirror, and Auto-lock of the patterns can be adjusted
manually.
3
4. Press the "
status.
" button when complete and return to browse
4
Clearing patterns or letters
1. Use the stitch width adjustment button to select the pattern
that you want to clear while in the memory mode.
1
2. Press the "
" button to delete the selected pattern and
the next pattern in the back will move forward.
2
61
MEMORY
MEMORY
Recalling and sewing the memorized pattern
1. Press the "
" button to enter memory mode and then input
the number of memory module when the cursor start flashing.
1
2. Input the number of memory module. (e.g. 2)
2
3. The LCD screen containing the various types of stitches will
open.
3
4. Press on the foot control or press the start/stop button to
start the sewing machine.
4
5. The cursor on the LCD screen will move along with the
sequential pattern while sewing.
Please Note: If the cursor stays in a vacant position in
the end, the machine will start sewing from the first
pattern. If the cursor stays under a specific pattern, the
machine will start sewing from that pattern.
5
6. Press the "
" button to leave memory mode and return to
the normal screen.
6
62
WARNING FUNCTIONS
WARNING FUNCTIONS
Warning animation message display
Presser foot is not lowered
The Start/stop button or reverse button was pressed
while the presser foot was raise.
BH lever is not lowered
The buttonhole or darning stitch was selected and the
start/stop button was pressed while the buttonhole lever
is raised.
BH lever is not lifted
A stitch other than the buttonhole or darning stitch was
selected and the start/stop button was pressed while the
buttonhole lever is down.
Return bobbin winder stopper to right
When the bobbin winder stopper is in left, press any
button (except the Start/stop button), the LCD screen will
display the animation of return bobbin winder stopper to
right.
The sewing machine is in trouble
The animation message means that the thread is twisted
or jammed and the hand wheel axle cannot move.
Please look through the "Trouble shooting guide" on
page 69/70 to find the solution. After the problem has
been solved, the machine will continue to sew.
63
WARNING FUNCTIONS
WARNING FUNCTIONS
Instruction animation message display
Bobbin winding
The bobbin winder is winding the bobbin.
Warning beeping sound
- When operating correctly: 1 beep
- When the memory is full 20 units of pattern: 2-short beeps
- When operating incorrectly: 3-short beeps
- When the sewing machine is in trouble and can't sew: 8 seconds short beeps
It means that the thread is twisted or jammed and the hand wheel axle can't move. Please look
through the "Trouble shooting guide" on page 69/70 to find the solution. After the problem has
been solved, the machine will continue to sew.
Please Note: If the problem is still not solved, please contact your local dealer.
Attention: During the sewing, if the thread get jammed inside the hook stopping the
needle from moving and you continue pressing the foot control, the security switch will
stop the machine completely. In order to restart the sewing machine, you will have to
turn the on/off switch to the OFF position and then ON again.
64
BUZZER SOUND
BUZZER SOUND
1
2
3
4
5
6
7
8
9
1. Press on the "
power switch.
OFF
" button and turn on the
ON
0
1
2. You can select the mode by pressing the
stitch width "+" or " " button. Select desired
mode sound on " "or sound off " ".
2
3. Pressing the "
" button. The Buzzer
sound setting mark will appear on the LCD
screen when you have set it.
3
65
REPLACING
REPLACINGTHE
THELIGHT
LIGHTBULB
BULB
Attention: Turn the power switch off and wait until the lamp has cooled down before
touching it.
Please Note:
- The 5W lamp is user-replaceable.
- The 240mW LED lamp is not user-replaceable.
1. Loosen the screw (a) on the left side of the
sewing head and remove the face plate (b).
a
b
1
2. If the machine is equipped with a 5W lamp,
replace the bulb as follows:
Pull light bulb downward to remove.
Replace the bulb with same type rated 5W.
Replace the face plate and tighten the
screw.
PUSH
2
3. If the machine is equipped with a 240mW
LED lamp, you must contact the
manufacturer or its service agent for repair
in the event of failure.
3
66
MAINTENANCE
MAINTENANCE
Attention: Disconnect the power cord from the wall socket before cleaning the screen and
sewing machine surface, otherwise injury or electrical shock may result.
Cleaning the screen
If the front panel is dirty, wipe it gently with a
soft, dry cloth.
Do not use any organic solvents or detergents.
Cleaning the sewing machine surface
If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it out
firmly and then wipe the surface. After cleaning it once in this way, wipe the surface again with a
dry cloth.
Cleaning the hook
If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of the
machine. Check regularly and clean the stitching mechanism when necessary.
Attention: Disconnect the machine from the wall outlet before carrying out any maintenance.
1. Remove the bobbin cover plate and bobbin.
1
2. Clean the bobbin holder with a brush.
2
67
MAINTENANCE
MAINTENANCE
3. Remove the needle, presser foot and
presser foot holder. Remove the bobbin
cover plate and bobbin. Remove the screw
holding the needle plate and remove the
needle plate.
3
4. Lift up the bobbin case and remove it.
4
5. Clean the hook race, feed dog and bobbin
case with a brush. Also clean them, using a
soft, dry cloth.
5
6. Replace the bobbin case into the hook race
so that the tip (a) fits to the stopper (b) as
shown.
6
a
b
68
TROUBLE
TROUBLESHOOTING
SHOOTINGGUIDE
GUIDE
Before calling for service, check the following items. If the problem still persists, contact the place of
purchase or your nearest authorized dealer.
Problem
Cause
Correction
1.The machine is not threaded correctly.
1.Rethread the machine.
Page 15
2.The thread tension is too tight.
2.Reduce the thread tension (lower
number).
Page 18
3.Select a larger needle.
Page 10
3.The thread is too thick for the needle.
Upper thread
4.The needle is not inserted correctly.
breaks
4.Remove and reinsert the needle (flat
side towards the back).
5.The thread is wound around the spool 5.Remove the reel and wind thread onto
holder pin.
reel.
Page 10
6.The needle is damaged.
Page 10
6.Replace the needle.
1.The bobbin case is not inserted 1.Remove and reinsert the bobbin case
correctly.
and pull on the thread. The thread
should pull easily.
Lower thread
breaks
2.The bobbin case is threaded wrong.
Skipped
stitches
Seam
gather or
pucker
Page 14
2.Check both bobbin and bobbin case.
Page 14
3.Loosen lower thread tension as
described.
Page 18
1.The needle is not inserted correctly.
1.Remove and reinsert needle(flat side
towards the back).
Page 10
2.The needle is damaged.
2.Insert a new needle.
Page 10
3.The wrong size needle has been used.
3.Choose a needle to suit the thread.
Page 10
4.The foot is not attached correctly.
4.Check and attach correctly.
Page 71
5.The machine is not threaded correctly.
5.Rethread the machine.
Page 15
Page 9
1.The needle is damaged.
1.Insert a new needle.
Page 10
2.The needle is not correctly inserted.
2.Insert the needle correctly (flat side
towards the back).
3.Choose a needle to suit the thread and
fabric.
Page 10
4.The wrong foot is attached.
4.Select the correct foot.
Page 71
5.The needle clamp screw is loose.
5.Use the screwdriver to firmly tighten
the screw.
Page 10
6.The presser foot that is used is not 6.Attach the presser foot that is approappropriate for the type of stitch that
priate for the type of stitch that you
you wish to sew.
wish to sew.
Page 71
7.The upper thread tension is too tight.
7.Loosen the upper thread tension.
Page 18
1.The machine is not correctly threaded.
1.Check the threading.
Page 15
3.Wrong needle size for the fabric.
Loose
stitches
Page 15
3.The lower thread tension is too tight
6.The presser foot pressure is not strong 6.Adjusting the presser foot pressure.
enough.
Needle
breaks
Reference
2.The bobbin case is not correctly 2.Thread the bobbin case as illustrated.
threaded.
3.Needle/fabric/thread combination is 3.The needle size must suit the fabric
and thread.
wrong.
Page 10
Page 14
Page 10
4.Thread tension is wrong.
4.Correct the thread tension.
Page 18
1.The needle is too thick for the fabric.
1.Select a finer needle.
Page 10
2.The stitch length is adjusted wrong.
2.Readjust the stitch length.
Page 24
3.The thread tension is too tight.
3.Loosen the thread tension.
Page 18
69
TROUBLE
TROUBLESHOOTING
SHOOTINGGUIDE
GUIDE
Problem
Cause
Correction
1.The needle thread tension is too tight.
Seam
puckering
Patterns are
distorted
The
machine
jams
The
machine is
noisy
The sewing
machine
doesn't
operate
Page 18
2.The needle thread is not threaded 2.Rethread the machine.
correctly.
Page 15
3.The needle is too heavy for the fabric 3.Choose a needle to suit the thread and
fabric.
being sewn.
Page 10
4.The stitch length is too long for the 4.Make stitch dense.
fabric.
Page 24
5.The presser foot pressure is not 5.Adjusting the presser foot pressure.
correctly adjusted.
Page 9
1.The correct presser foot is not used.
1.Select the correct foot.
Page 71
2.The needle thread tension is too tight.
2.Loosen the thread tension .
Page 18
3.The stitch length is not suitable for the 3.Make stitch adjust.
fabric being sewn.
Page 24
4.Feed balancing dial is not set properly.
4.Adjusting pattern balance.
Page 39
1.Thread is caught in the hook.
Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remands.
Page 67
1.Fluff or oil have collected on the hook 1.Clean the hook and feed dog as
or needle bar.
described.
Page 67
2.Poor quality oil has been used.
2.Only use good quality sewing machine
oil
Page 10
3.The needle is damaged.
3.Replace the needle.
Page 10
2.The feed dogs are packed with lint.
4.Slight humming sound coming from 4.Normal
internal motor.
-Page 67
6.The feed dogs are packed with lint.
Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remands.
1.Poor quality thread.
1.Select a better quality thread.
Page 10
2.The bobbin case is threaded wrong.
2.Remove the bobbin case, the thread
and reinsert correctly.
Page 14
3.Fabric has been pulled.
3.Do not pull on the fabric while sewing,
let it be taken up by the machine.
--
1.The machine is not turned on.
1.Turn on the machine.
Page 7
2.The Start/stop button was not pressed.
2.Press the Start/stop button.
Page 21
3.The presser foot lever is raised.
3.Lower the presser foot lever.
Page 20
5.Thread is caught in the hook.
Uneven
stitches,
uneven feed
1.Lossen the thread tension.
Reference
4.The Start/stop button was pressed, 4.Do not use Start/stop button when the
even through the foot controller is
foot controller is con-nected. To use
connected.
Start/stop button, disconnect the foot
controller.
Page 21
5.A thread is caught in the hook race.
5.Remove the upper thread and bobbin
case, turn the handwheel backwards
and forwards by hand and remove the
thread remands.
Page 67
6.The machine is not plugged in.
6.Connect the power line plug to the
electric outlet.
Page 7
70
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
Stitch Pattern
Utility
stitches
Buttonhole
stitches
Darning
stitches
Satin
stitches
Width (mm)
Length (mm)
Manual
Presser
Foot
Functions
Reverse
Mirror/ Twin needle Memory
Auto-lock Elongation Presser
foot
Auto
Manual
Auto
00
3.5
0.0~7.0
2.5
0.0~4.5 T(P/K/I)
/T
01
0.0
0.0~7.0
2.5
0.0~4.5 T(P/K/I)
/T
02
3.5
0.0~7.0
2.5
1.0~3.0
T(P)
/T
03
3.5
1.0~6.0
2.5
1.0~3.0
T
/T
04
3.5
0.0~7.0
2.5
1.5~3.0
T
/T
05
5.0
0.0~7.0
2.0
0.3~4.5
T(E)
/T
06
5.0
2.0~7.0
1.0
0.3~4.5
T
/T
07
5.0
2.5~7.0
2.5
1.0~3.0
T(A)
/T
08
5.0
3.5~7.0
2.5
1.0~3.0
E
/T
09
5.0
2.5~7.0
2.5
1.0~3.0
T
/T
10
3.5
2.5~7.0
2.0
0.5~4.5
F
/T
11
3.5
2.5~7.0
1.0
0.5~4.5
F
/T
12
3.5
2.5~7.0
2.5
1.0~3.0
T
/T
13
5.0
2.5~7.0
2.5
1.0~3.0
T(A)
/T
14
7.0
2.5~7.0
2.5
1.0~3.0
A
/A
15
6.0
2.5~7.0
2.5
1.0~3.0
A(M)
/A
16
5.0
2.5~7.0
0.5
0.3~1.0
D
17
5.5
3.0~7.0
0.5
0.3~1.0
D
18
5.0
2.5~5.5
0.5
0.3~1.0
D
19
6.0
3.0~7.0
0.5
0.3~1.0
D
20
5.0
2.5~5.5
0.5
0.3~1.0
D
21
5.0
2.5~5.5
0.5
0.3~1.0
D
22
7.0
5.5~7.0
0.5
0.3~1.0
D
23
7.0
5.5~7.0
0.5
0.3~1.0
D
24
7.0
5.5~7.0
0.5
0.3~1.0
D
25
6.0
3.0~7.0
1.0
1.0~2.0
D
26
6.0
3.0~7.0
1.5
1.0~3.0
D
27
7.0 7.0,6.0,5.0
28
7.0
3.5~7.0
2.0
1.0~2.0
D
29
7.0
3.5~7.0
2.0
1.0~2.0
D
30
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
31
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
32
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
33
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
34
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
35
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
36
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
37
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
38
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
39
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
A
: Adjustments can be made.
71
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
Satin
stitches
Cross
stitches
Decorative
stitches
Width (mm)
Length (mm)
Functions
Auto
Manual
Auto
Manual
Presser
Foot
40
7.0
2.5~7.0
0.5
0.3~1.0
A
/A
41
7.0
2.5~7.0
1.5
0.5~3.0
A
/A
42
7.0
2.5~7.0
1.0
0.5~2.0
A
/A
43
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
44
5.0
2.5~7.0
2.5
1.0~3.0
A
/A
45
6.0
2.5~7.0
1.0
0.5~3.0
A(T)
/A
46
6.0
2.5~7.0
1.0
0.5~3.0
A
/A
47
4.0
2.5~7.0
1.0
0.5~3.0
A
/A
48
4.0
2.5~7.0
1.0
0.5~3.0
A
/A
49
6.0
2.5~7.0
1.0
0.5~3.0
A
/A
50
6.0
2.5~7.0
1.0
0.5~3.0
A
/A
51
6.0
2.5~7.0
1.0
0.5~3.0
A
/A
52
5.0
2.5~7.0
2.5
1.0~3.0
A(T)
/A
53
5.0
2.5~7.0
2.5
1.0~3.0
A
/A
54
5.0
2.5~7.0
2.5
1.0~3.0
A
/A
55
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
56
5.0
2.5~7.0
2.5
1.0~4.5
A
/A
57
7.0
2.5~7.0
2.0
1.0~3.0
T(A)
/T
58
5.0
2.5~7.0
2.5
1.0~3.0
T(A)
/T
59
7.0
2.5~7.0
1.5
1.0~3.0
A(T)
/A
60
6.0
2.5~7.0
1.5
1.0~3.0
A
/A
61
7.0
2.5~7.0
2.5
1.0~3.0
T
/T
62
7.0
2.5~7.0
2.5
1.0~4.5
A(T)
/A
63
7.0
2.5~7.0
2.5
1.0~3.0
A
/A
64
7.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
65
5.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
66
5.0
2.5~7.0
1.0
0.5~3.0
A
/A
67
7.0
2.5~7.0
3.0
1.0~3.0
A(T)
/A
68
5.0
2.5~7.0
1.0
0.5~4.5
T
/T
69
5.0
2.5~7.0
1.0
0.5~3.0
A(T)
/A
70
5.0
2.5~7.0
1.0
1.0~3.0
A(T)
/A
71
6.0
2.5~7.0
1.0
1.0~3.0
A
/A
72
6.0
2.5~7.0
2.0
1.0~3.0
A
/A
73
7.0
2.5~7.0
3.0
1.0~3.0
A
/A
74
7.0
2.5~7.0
3.0
1.0~3.0
A
/A
75
7.0
2.5~7.0
2.5
1.5~3.0
A(T)
/A
76
7.0
2.5~7.0
2.5
1.0~3.0
A(T)
/A
77
7.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
78
7.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
79
7.0
2.5~7.0
2.5
1.0~3.0
A(T)
/A
Stitch Pattern
Reverse
Mirror/ Twin needle Memory
Auto-lock Elongation Presser
foot
: Adjustments can be made.
72
QUICK ADJUSTMENT REFERENCE CHART
QUICK ADJUSTMENT REFERENCE CHART
Stitch Pattern
Decorative
stitches
Width (mm)
Length (mm)
Auto
Manual
Presser
Foot
Functions
Reverse
Mirror/ Twin needle Memory
Auto-lock Elongation Presser
foot
Auto
Manual
80
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
81
7.0
2.5~7.0
3.0
1.5~4.5
A
/A
82
7.0
2.5~7.0
3.0
1.0~3.0
A
/A
83
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
84
7.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
85
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
86
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
87
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
88
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
89
7.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
90
7.0
2.5~7.0
2.0
1.0~3.0
A
/A
91
7.0
2.5~7.0
2.5
1.0~3.0
A(T)
/A
92
7.0
2.5~7.0
3.0
1.0~3.0
A(T)
/A
93
5.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
94
5.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
95
5.0
2.5~7.0
3.0
1.0~3.0
A(T)
/A
96
5.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
97
5.0
2.5~7.0
2.0
1.0~3.0
A(T)
/A
98
7.0
2.5~7.0
2.5
1.0~3.0
A
/A
99
5.0
2.5~7.0
3.0
1.0~3.0
A
/A
: Adjustments can be made.
73
021D3B0101(C)( ) Aug/05
EURO-PRO 9110(9000B)