User manual | Excell Precision FM Scale User Manual

EXCELL PRECISION CO., LTD.
User Manual
© Excell Precision Limited 2006. All rights reserved Worldwide.
The information contained herein is the property of Excell Precision Limited and is supplied
without liability for errors or omissions. No part may be reproduced or used except as
authorised by contract or other written permission. The copyright and the foregoing
restriction on reproduction and use extend to all media in which the information may be
embodied.
FM User Manual
SME300000119
EXCELL PRECISION CO., LTD.
TABLE OF CONTENT
SAFETY PRECAUTION....................................................................... 3
<CHAPTER 1>
FEATURES AND SPECIFICATION.......................... 4
1-1 FEATURES............................................................................................................................ 4
1-2 SPECIFICATION ..................................................................................................................... 5
<CHAPTER 2>
KEYPAD OPERATION INSTRUCTION .................... 6
<CHAPTER 3>
FRONT & REAR PANELS........................................ 7
3-1 FRONT PANEL ...................................................................................................................... 7
3-2 REAR PANEL ........................................................................................................................ 8
<CHAPTER 4>
INSTALLATION........................................................ 9
4-1 LOAD CELL .......................................................................................................................... 9
4-2 DIMENSION......................................................................................................................... 10
4-3 BATTERY ASSEMBLY .......................................................................................................... 11
<CHAPTER 5>
INTERNAL CALIBRATION .................................... 12
...................................................................... 13
5-1 SPECIFICATION SETTING
2
2
Specification Parameter Description .........................................................................................................14
Parameter Display Description ...................................................................................................................15
5-2 INTERNAL WEIGHT CALIBRATION
2
.......................................................... 16
Password Setting..........................................................................................................................................17
5-3 INTERNAL FUNCTION SETTING
2
2
.............................................................. 18
Internal Function Parameter Description ..................................................................................................19
Error Message ................................................................................................................................................20
<CHAPTER 6>
SPECIAL FUNCTION ............................................. 21
6-1 ANIMAL SCALE FUNCTION SETTING ................................................................................... 21
6-2 DUAL RANGE RESOLUTION SWITCH FUNCTION ................................................................... 22
6-3 PRE-TARE FUNCTION ........................................................................................................ 23
6-4 RESOLUTION SWITCH FUNCTION ........................................................................................ 23
FM User Manual
1
SME300000119
EXCELL PRECISION CO., LTD.
<CHAPTER 7>
TRANSMISSION INTERFACE ............................... 24
7-1 OP-01 RS232 / RS485 SERIAL OUTPUT (WITH RTC)........................................................ 24
2
2
Pin Allocation of Rear Panel........................................................................................................................24
Connection Description (RS485) ................................................................................................................25
<CHAPTER 8>
FUNCTION PARAMETER SETTING...................... 26
8-1 FUNCTION SETTING
2
Function Parameter Setting.........................................................................................................................28
8-2 RS232 SETTING
2
2
2
........................................................................... 27
............................................................................... 29
OP-01 RS232 / RS485 Interface Function ..................................................................................................30
Transmission Format....................................................................................................................................32
Command Mode.............................................................................................................................................33
<CHAPTER 9> MAINTENANCE ..................................................... 34
9-1 DEFAULT RECOVERY FOR ALL PARAMETERS........................................................................ 34
9-2 DEFAULT RECOVERY FOR GENERAL FUNCTION PARAMETERS ............................................... 34
9-3 SELF-DIAGNOSIS MODE....................................................................................................... 34
9-3-1 Program Version Number.........................................................................................................................35
9-3-2 7-segment Display Testing.......................................................................................................................35
9-3-3 Keypad & Calibration Switch Testing.....................................................................................................35
9-3-4 AD Conversion Value ................................................................................................................................35
9-3-5 EEPROM Testing........................................................................................................................................35
9-3-6 RTC Time & Date Testing..........................................................................................................................35
9-3-7 RS-232 Serial Output Interface Testing ( OP-01 ) .................................................................................35
FM User Manual
2
SME300000119
EXCELL PRECISION CO., LTD.
BEFORE USING THE INDICATOR
Thanks for purchasing EXCELL FM Mini-indicator. In
order to operate smoothly, to last the durability, and to
reduce the chance of breakdown for this product,
please read the following instructions carefully.
Safety Precaution
&
Turn off power before installing or disassembling.
& Keep the product away from sunshine. The temperature range for operation
is -10℃ ~ +40℃.
& To connect the ground is a must for this equipment. The ground impedance
is less than 100Ω.
& Never connect the ground with other equipments which are huge in power
consumption.
& No ground or incorrect ground connecting might cause the electric shocks or
breakdowns.
FM User Manual
3
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 1> Features and Specification
1-1 Features
l Large and clear LCD (height 25.4mm × 10mm)
l LED Backlight, more duration, more energy saving
l Auto zero tracking
l Weighing calibration in both kilogram and pound
l High resolution switch function to display 10 times divisions
l Weighing unit shift function & data accumulation function
l Adjustable digital filter
l Available in connecting with up to four 350-ohm load cells
l Capable of connecting with 6-wire load cells
l
Convenient to operate power switch in front panel
FM User Manual
4
SME300000119
EXCELL PRECISION CO., LTD.
1-2 Specification
Analog Specification
♦
♦
♦
♦
♦
Load Cell Current: DC 5V ±5% 60mA (Up to Four 350Ω Load Cells)
Max. Load Cell Input Voltage: 16 mV
Input Sensitivity: 0.12µV/D or more
Conversion Rate: Approximately 100 times/sec. (max.)
Resolution: 19 bits
Digital Specification
♦
♦
♦
♦
♦
♦
Display: LCD, 6 digits, height 25.4x10mm, LED backlight
Display Frequency: 50 times/sec. (max.)
Display Range: - 999999 ~ 999999
Min. Division: 1, 2, 5, 10, 20, 50
Decimal Point: 0, 0.0, 0.00, 0.000, 0.0000
Memory: Calibration parameter and function setting are all stored in EEPROM.
Optional Interface
♦
OP-01
RS-232 / RS-485 (Includes RTC Function)
Power Requirement
♦ Adaptor Spec.: Input 120/230VAC 50~60Hz, output 9V/1000mA
♦ 6V/5pcs Hi-MH rechargeable battery kit (1800mA/1hr)
♦ Max. Power Consumption (by rechargeable battery):
120mA (with 4 Load Cells + backlight + RS-232 interface) →15 hours
50mA (with 1 Load Cell + no backlight + no RS-232 interface) →36 hours
Others
♦ Operation Temperature: -10 ℃ ~ 40 ℃
♦ Operation Humidity: < 85% R.H.
♦ Dimension: W 49.5 × L193 × H134 (mm)
♦ Weight: 700 (g)
FM User Manual
5
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 2> Keypad Operation Instruction
Function
General Function
Setting
Operation
Description
Press and hold
ENTER
and then press
F1
,
Refer to <Chapter 8> Function
Parameter Setting for details
Weighing
Parameter Setting
Adjust calibration
switch to ON
Setting for decimal point, capacity,
division, zero tracking, and unstable
detecting, etc. Refer to 5-1
Specification Setting for details.
Calibration
Adjust calibration
switch to ON
Refer to 5-2 Internal Weight
Calibration for operation.
Self-diagnosis
Mode
While turning on with
countdown, press and
hold ZE RO .
Refer to 9-3 Self-diagnosis Mode
for details.
Adjust calibration switch
Default Recover to ON, and then press
for All Parameters and hold F1 ENTER .
Default Recovery
While turning on with
for General
countdown, press and
Function
hold F1 ENTER .
Parameters
Refer to 9-1 for details.
Refer to 9-2 for details.
4
During the operation, use the following keys to complete all the
works.
ZERO
⇒ To add the value flashing
TARE
⇒ To reduce the value flashing
GROSS
NET
⇒ To move the cursor leftward
3
FM User Manual
F2
4
ENTER
ESC
⇒ To move the cursor rightward
⇒ Storage setting
⇒ To abort setting/to escape
6
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 3> Front & Rear Panels
3-1 Front Panel
R
+ -
TARE
ESC
MOTION
ZERO
+
M+
TARE
GROSS
GROSS
NET
PT
F2
F1
ENTER
Indication:
:
:
TARE
:
MOTION :
M+
:
GROSS :
PT
:
Battery charged status
Battery charging status
Tare status
Unstable weighing indication
Accumulation status indication
Gross weight
Pre-tare
Keypad:
ESC
ZERO
TARE
GROSS
NET
3
F2
4
F1
ENTER
1) Power ON / OFF. Press and hold this key for 3 seconds to shut down.
2) To abort or escape when setting.
1) Weight re-zero.
2) To add the value when setting.
1) To eliminate the gross weight.
2) To reduce the value when setting.
1) To switch Gross / Net weight shown on display.
2) To move the cursor leftward when setting.
1) Keypad function (FNC-02 & FNC-03)
2) To move the cursor rightward when setting.
Keypad function (FNC-02 & FNC-03)
Confirmation key.
FM User Manual
7
SME300000119
EXCELL PRECISION CO., LTD.
3-2 Rear Panel
1
2
5
3
4
1. Battery Case
2. RS232/485 Input/Output
3. DC 9V Power Input
4. Calibration Switch
5. Load Cell Connect Socket
FM User Manual
8
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 4> Installation
4-1 Load Cell
5
4
9
3
8
2
7
1
6
Load cell cable
Load cell
EXC+
SEN+
SIG+
SIG-
EXCSEN-
Shield
4-wired (5-wired) Load Cell
Short Pin4&5 to connect with EXC+
Short Pin2&3 to connect with EXCPin1 connects with SIG+
Pin9 connects with SIGPin6, 7, 8 connect with Shield
FM User Manual
6-wired (7-wired) Load Cell
Pin5 connects with EXC+
Pin4 connects with SEN+
Pin3 connects with EXCPin2 connects with SENPin1 connects with SIG+
Pin9 connects with SIGPin6, 7, 8 connect with Shield
9
SME300000119
EXCELL PRECISION CO., LTD.
4-2 Dimension
FM User Manual
10
SME300000119
EXCELL PRECISION CO., LTD.
4-3 Battery Assembly
將多餘的電線塞入電池孔中
Stuff
the surplus wires into the battery case.
FM User Manual
11
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 5> Internal Calibration
Adjust calibration switch to “ON”, and the screen displays:
After 2 seconds
ENTER
Press
ZERO
Press
TARE
ENTER
ZE RO
Press
Press
TARE
ENTER
Adjust calibration switch back to “OFF”.
⇒ Specification Setting
⇒ Internal Weight Calibration
⇒ Internal Function Setting
FM User Manual
12
SME300000119
EXCELL PRECISION CO., LTD.
5-1 Specification Setting
*Parameter Code
Press
ENTER
⇒ Decimal Point
⇒ Capacity
⇒ Division 1
Input the *Parameter
Code intended
⇒ Division 2
⇒ Zero Tracking Setting
ENTER
⇒ Unstable Detecting Setting
Press
The screen displays the parameters set previously.
Input the parameters intended and then press ENTER .
Continue other functions setting
or press
to escape.
ZERO
⇒ To add the value flashing
TARE
⇒ To reduce the value flashing
GROSS
NET
⇒ To move the cursor leftward
E SC
3
F2
4
⇒ To move the cursor rightward
ENTER
⇒ Storage setting
ESC
FM User Manual
13
⇒ To abort setting / escape
SME300000119
EXCELL PRECISION CO., LTD.
2
Specification Parameter Description
Setting
Parameter
Function
Code
Description
Parameter
Decimal
Point
CSP-00
CSP-01
CSP-02
Default
Setting
Refer to the description on next page.
Capacity
999999
↓
000000
Max. value for weight display
999999
Division 1
1
2
5
10
20
50
Min. value for weight display
1
Min. value for Weight display
1
1
2
CSP-03
Division 2
5
10
20
50
CSP-04
CSP-05
Zero
Tracking
Setting
Unstable
Detecting
Setting
FM User Manual
Refer to the description on next page.
Refer to the description on next page.
14
SME300000119
EXCELL PRECISION CO., LTD.
2
Parameter Display Description
CSP-00
Decimal Point
Display
Decimal Point Digit
None
CSP-04
.
1 Digit
.
2 Digits
.
3 Digits
.
4 Digits
Zero Tracking Setting
Display
Division/Period
0.25 D/1 sec
.
0.5 D/1 sec
.
0.75 D/1 sec
.
1D/1 sec
1.25 D/2 sec
.
1.5 D/2 sec
.
1.75 D/2 sec
.
2 D/2 sec
No Zero Tracking
CSP-05
Unstable Detecting Setting
Display
Division / Period
0.25 D/1 sec
.
.
0.5 D/1 sec
0.75 D/1 sec
.
1D/1 sec
1.25 D/2 sec
.
.
.
1.5 D/2 sec
1.75 D/2 sec
2 D/2 sec
No Unstable Detecting
FM User Manual
15
SME300000119
EXCELL PRECISION CO., LTD.
5-2 Internal Weight Calibration
Turn on and warm up the machine for 15 to 30 minutes before calibration.
Adjust calibration switch to “ON”, and the screen will display
Press
TARE
or
ZERO
to select
.
.
Procedure
ENTER
ENTER
Zero
Calibration
Zero calibration complete
ESC
ENTER
Weight
Calibration
Place the
weight mass
and set the
weight
ENTER
Confirmed
ESC
Calibration
Switch “OFF”
Zero Calibration
ENTER
a ) Ensure nothing on the platter; after being stable, press
, and the screen will display
“ ……. ”. The zero calibration will be complete 5 seconds later.
b ) To abort zero calibration, just press
.
ESC
Weight Calibration
a ) Place an object, whose weight is known, on the platter, and input the weight value from
front panel. After being stable, press ENTER and the screen will display “……. ”. The
weight calibration will be complete 5 seconds later.
b ) To abort weight calibration, just press
.
ESC
FM User Manual
16
SME300000119
EXCELL PRECISION CO., LTD.
2 Password Setting
Adjust calibration
switch to “ON”
After 2 seconds
ZERO
F1
Input new password
4 “0000” means no password.
ENTER
Confirm new password
(re-input again)
ENTER
4
After complete password setting, when entering calibration mode or function
setting mode, the screen displays
for 1 second, and then
.
It’s necessary to input the correct password to continue each setting.
If the password inputted is not correct, the screen displays
FM User Manual
17
.
SME300000119
EXCELL PRECISION CO., LTD.
5-3 Internal Function Setting
Press
ENTER
*Parameter Code
⇒ Tare or Zero Function under
Unstable Status
⇒ Turning on Re-zero
Input the *Parameter
code intended
⇒ Re-zero Range
⇒ Filter Strength
Press
ENTER
⇒ AD Sampling Rate
⇒ Animal Scale Mode
The screen displays
the parameters set
previously. Input the
parameters intended
and then press ENTER
⇒ Animal Scale Stable Range
⇒ Animal Scale Sampling
Frequency
⇒ Dual Range Resolution
Setting
⇒ Dual Range Resolution
Middle Point Setting
Continue other functions setting
or press
to escape.
ESC
ZERO
⇒ To add the value flashing
TARE
⇒ To reduce the value flashing
GROSS
NET
⇒ To move the cursor leftward
3
F2
4
⇒ To move the cursor rightward
ENTER
⇒ Storage setting
ESC
FM User Manual
18
⇒ To abort setting / escape
SME300000119
EXCELL PRECISION CO., LTD.
2
Internal Function Parameter Description
Setting
Parameter
Function
Code
Description
Parameter
CFN-00
CFN-01
Default
Setting
Tare or Zero
Function under
Unstable Status
0
1
OFF
Re-zeroing after
Turning on
0
OFF
1
ON
0
2
ON
0
CFN-02
Re-zero Range
0% ~ 30%
0%: Full range re-zero
1% ~ 30%:
Capacity × ± setting value%
CFN-03
Filter Strength
0~5
Strength increases by number
0
No limit
1
20 times/sec.
2
10 times/sec.
3
0
5 times/sec.
OFF
CFN-04
CFN-05
CFN-06
CFN-07
CFN-08
CFN-09
FM User Manual
AD Sampling
Rate
Animal Scale
Mode
Animal Scale
Stable Range
Animal Scale
Sampling
Frequency
Dual Range
Resolution
Setting
Dual Range
Resolution
Middle Point
Setting
1
Mode 1: No weight display
under unstable status
2
Mode 2: Weight display whether
under stable or unstable status
0 ~ 100
Mode 2: Stable Range Setting
0
8 times
1
16 times
2
32 times
3
64 times
4
128 times
0
Multi-interval
1
Multi-range
0
2
0
30
2
0
0 ~ 65535
5000
19
SME300000119
EXCELL PRECISION CO., LTD.
2
Error Message
(1)
Load Cell or A/D circuit extraordinary
(2)
Real weighing value ≦ zero value
(3)
Internal resolution < 0.12μV/D range
(4)
.
Incorrect password
(5)
Turning on zero ≦ zero range
(6)
Turning on zero ≧ zero range
FM User Manual
20
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 6> Special Function
6-1
Animal Scale Function Setting
2 CFN-05 = 1
(Animal Scale Mode1: No weight display under unstable status)
When no any object is on the platter, the screen will display:
When the object is on the platter, after weight has been measured, the screen will
display:
.
If the display weight value keeps being lower than zero plus 10d, the screen will
display:
2 CFN-05 = 2
(Animal Scale Mode 2: Weight display weather under unstable or
stable status)
When the weight value reaches the range of CFN-06 and CFN-07 setting, the screen
will keep displaying the weight value.
When the weight value is over the range of CFN-06 and CFN-07 setting, the screen will
display the normal weight measurement.
Example: CFN-06=30
CFN-07=2
WT
Weight Holding
重量保持
30d
Weight Holding Cancellation
取消重量保持
32次
10d
T
32 Times
FM User Manual
21
SME300000119
EXCELL PRECISION CO., LTD.
6-2
Dual Range Resolution Switch Function
If the setting of CSP-02 is not the same as CSP-03, the dual range resolution
will be activated.
2 CFN-08 = 0 ⇒ Multi-interval
If CFN-09 = 5000
WT
Division 2
最小刻度2
2
5000
1
0
最小刻度1
Division 1
2 CFN-08 = 1 ⇒ Multi-range
If CFN-09 = 5000
WT
2
2
5000
2
0
FM User Manual
1
回到零點才恢復
Recover when back to zero
22
SME300000119
EXCELL PRECISION CO., LTD.
6-3
Pre-tare Function
2 FNC-02 or FNC-03 setting is at parameter 6. (Pre-tare Function)
Under weight display status, press
screen will display:
F1
or
F2
4
key (according to FNC setting), the
Input the pre-tare
value intended
Press
ENTER
key
Back to weight display status (PT indication lights up)
Pre-tare Cancellation
When the gross weight is displayed as “0”, press
6-4
TARE
key to cancel the pre-tare value.
Resolution Switch Function
2 FNC-02 or FNC-03 setting is at parameter 5. (HR)
F1
F2
Under weight display status, press
or 4 key (according to FNC setting), the
screen will display 10 times resolution, and then, recovery back to original after 5
seconds.
FM User Manual
23
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 7> Transmission Interface
7-1
OP-01 RS232/RS485 Serial Output (with RTC)
CN3
CN2
123
123
To short 1 and 2 pins is RS485 output.
To short 2 and 3 pins is RS232 output.
2
Pin Allocation of Rear Panel
4
5
9
4
3
8
1
2
7
Pin
Function
2
3
RXD
TXD
SG
DA
DB
5
6
7
6
RS485 interface is capable to connect up to 10 mini-indicators.
FM User Manual
24
SME300000119
EXCELL PRECISION CO., LTD.
2
Connection Description (RS485)
終端電阻
終極電阻
Terminal
Resistant
Host
電腦主機
EX0419 # 1
RS - 06 = 01
EX0419 # 2
RS - 06 = 02
EX0419 # 10
RS - 06 = 10
4 Notice
♦
♦
If the terminal resistant is built-in the host interface, it’s not necessary to connect with
another one outside.
If the host computer is no signal ground (SG), it’s not necessary to connect with it.
FM User Manual
25
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 8> Function Parameter Setting
Under general weight display status, press
F1
ENTER
, and the screen will display:
ENTER
Press
ZER O
Press
TARE
key
key
ENTER
Press ESC to escape.
Back to general weight display status.
⇒ External function setting
⇒ RS232/RS485 interface function
FM User Manual
26
SME300000119
EXCELL PRECISION CO., LTD.
8-1
Function Setting
*Parameter Code
Press
⇒ Key Disable
ENTER
⇒ DSP Update
⇒ F1 Key Function Setting
Input the *parameter
code intended
⇒ F2 Key Function Setting
⇒ Backlight Setting
Press
ENTER
The screen displays the parameters set previously.
Input the parameters intended and then press ENTER .
Continue other function settings
or press
to escape
ZERO
⇒ To add the value flashing
TARE
⇒ To reduce the value flashing
ESC
GROSS
NET
3
F2
4
⇒ To move the cursor rightward
ENTER
⇒ Storage setting
ESC
FM User Manual
27
⇒ To move the cursor leftward
⇒ To abort setting or escape
SME300000119
EXCELL PRECISION CO., LTD.
2
Function Parameter Setting
Parameter
Function
Code
FNC-00
FNC-01
Key Disable
DSP Update
F1 Key
Function
Setting
FNC-02
F2 Key
Function
Setting
FNC-03
Setting
Parameter
0000
↓
1111
FNC-04
FM User Manual
Description
0
ON 0000 is corresponding to:
1 OFF
ZERO
TARE
GROSS
NET
3
F2
4
0000
(from left to right)
0
No Limit
1
20 times/sec.
2
10 times/sec.
3
5 times/sec.
4
0
1 times/sec.
Print (printing)
1
Units (units switch)
2
M+ (accumulation and printing)
3
MC (memory clearing)
4
Weight/Weight Accumulation/Times
Accumulation Display Switch
5
HR (high resolution switch)
6
0
Pre-tare (pre-tare function)
Print (printing)
1
Units (units switch)
2
M+ (accumulation and printing)
3
MC (memory clearing)
4
Weight/Weight Accumulation/Times
Accumulation Display Switch
5
HR (high resolution switch)
6
Pre-tare (pre-tare function)
Auto Backlight On
(backlight on in operation only)
0
Backlight
Setting
Default
Setting
1
Backlight On (backlight always on)
2
Backlight Off
28
1
0
1
0
SME300000119
EXCELL PRECISION CO., LTD.
8-2
RS232 Setting
*Parameter Code
Press
ENTER
⇒ Information Pattern
⇒ Transmission Method
⇒ Transmission Rate
Input the *Parameter
code intended
⇒ Parity, Bit Length, Stop Bit
⇒ Unstable or Over Load
Press
ENTER
⇒ Auto Transmission
Condition
⇒ Command Address
The screen displays
the parameters set
previously. Input the
parameters intended
and then press ENTER
⇒ Output Format
⇒ Transmission Times
⇒ Date Setting
⇒ Time Setting
Continue other functions setting
or press
ESC
to escape.
ZERO
⇒ To add the value flashing
TARE
⇒ To reduce the value flashing
GROSS
NET
3
F2
4
⇒ To move the cursor rightward
ENTER
⇒ Storage setting
ESC
FM User Manual
29
⇒ To move the cursor leftward
⇒ To abort setting / escape
SME300000119
EXCELL PRECISION CO., LTD.
2
OP-01 RS232 / RS485 Interface Function
Parameter
Code
Function
RS1-00
Information
Pattern
RS1-01
Transmission
Method
RS1-02
Transmission
Rate
Parameter
0
1
2
3
4
5
6
0
1
2
3
4
0
1
2
3
4
0
Parity
Bit Length
Stop Bit
RS1-03
1
2
Setting
Description
Display Correspondingly
Gross Weight
Net Weight
Tare
Weight Accumulation
Times Accumulation
Output with Date & Time
Continuous Transmission
Auto Transmission
Press
F1
or
F2
4
to transmit
Command Mode (no address)
Command Mode (with address)
1200
2400
4800
9600
19200
No Parity
N, 8, 1
8 Bits Length
1 Stop Bit
Odd Parity,
O, 7, 1
7 Bits Length,
1 Stop Bit
Even Parity,
E, 7, 1
7 Bits Length,
1 Stop Bit
Default
Setting
0
0
1
2
RS1-04
Unstable or
Over Load
0
Continuous Output
1
Stop Output
0
RS1-05
Auto
Transmission
Condition
Positive (over + 10D)
Positive/negative
(over + 10D, under - 10D)
0
RS1-06
Command
Address
0
RS1-07
FM User Manual
Output
Format
1
0
00
↓
Available only if RS1-01 setting is “4”
99
0
Standard Format
1
UMC 600
30
0
SME300000119
EXCELL PRECISION CO., LTD.
RS1-08
Transmission
Times
RS1-09
Date Setting
RS1-10
Time Setting
FM User Manual
0
No Limit
1
1 times/sec.
2
2 times/sec
3
5 times/sec
4
10 times/sec
5
20 times/sec
31
4
SME300000119
EXCELL PRECISION CO., LTD.
2
Transmission Format
RS1-00 ⇒ 0 ~ 3
S
,
T
Header 1
G
S
,
1
+
Header 2
2
3
.
4
6
5
g CR LF
Weight Data ( 8 digits )
Header 1
ST : Stable Weight
/
US : Unstable Weight
Header 2
GS : Gross Weight
/
NT : Net Weight /
/
Unit Terminators
OL : Weight Over Load
TR : Tare
Weight Data ( 8 digits )
The first digit of weight data represents “+/-“ indication for weight value. The other 7
digits, including decimal point, represent the weight value. If the weight is over load
(Header 1 : OL), the screen turns into “blank” except “+/-“ indication and decimal point.
Unit
Kg, g, t, lb or “blank”
Terminators
CL and LF are data termination code.
RS1-00 = 4
T
N
,
1
2
3
CR
LF
,
+
1
2
3
4
.
RS1-00 = 5
T
W
5
6
k
g
CR
LF
X
X CR LF
RS1-00 = 6
D
A
T
E
:
2
0
X
X
/
X
X
/
T
I
M
E
:
X
X
:
X
X
:
X
X CR LF
G
R
O
S
:
+
1
2
3
4
.
5
6
k
g CR LF
N
E
T
:
+
1
2
3
4
.
5
6
k
g CR LF
T
A
R
:
+
1
2
3
4
.
5
6
k
g CR LF
T
N
:
X
X
X CR LF
T
W
:
+
1
2
.
5
6
k
g CR LF
FM User Manual
E
S
3
4
32
SME300000119
EXCELL PRECISION CO., LTD.
2
Command Mode
Command
Function
Command
Function
READ, RW
Weight Reading
CT
Tare Clearing
ZERO, MZ
Weight Re-zeroing
Rl
Weight Accumulation
TARE, MT
Gross Weight Reducing
Rm
Times Accumulation
NTGS
Gross / Net Switch
Rn
Date
MG
Gross Weight Indicating
Ro
Time
MN
Net Weight Indicating
AT
DT
Weight and Times
Accumulation
Weight and Times
Accumulation Clearing
Œ
After setting the commands mentioned above, it’s necessary to add the termination
code “CR(0DH) and LF(0AH)”.
• If the command is not correct, it will reply “E” + “Command Unidentified”.
Ž If setting command mode with address (RS1-06 = 4), add “@ address” in front of each
command.
Example: When RS1-08 = 1, for reading weight value, the whole complete command
should be “@01RW(CR)(LF)”.
FM User Manual
33
SME300000119
EXCELL PRECISION CO., LTD.
<Chapter 9> Maintenance
9-1 Default Recovery for All Parameters
(1) Adjust the calibration switch to “ON”, when re-zeroing after turning on, press
F1
ENTER
and hold simultaneously.
.
(2) The screen will display
.
ENTER
, and then adjust the
(3) If decided, press
and hold until displaying
calibration switch to “OFF”.
9-2 Default Recovery for General Function Parameters
(1) When re-zeroing after turning on, press
.
(2) The screen will display
F1
ENTER
and hold simultaneously.
.
ENTER
(3) If decided, press
and hold until re-turning on.
9-3 Self-diagnosis Mode
(1) When re-zeroing after turning on, press
(2) The screen will display
(3) Use
ZERO
Press
Item
or
ENTER
TARE
ZER O
and hold.
, which means entered self-diagnosis mode.
keys to select item intended to test.
key to enter self-diagnosis, and press
Display
ESC
key to escape.
Testing Item
1
Program Version Number Displaying
2
7-segment Display Testing
3
Keypad and Calibration Switch Testing
4
AD Conversion Value Displaying
5
EEPROM Testing
6
RTC Date & Time Testing
7
OP-1 RS232 Serial Output Interface Testing
FM User Manual
34
SME300000119
EXCELL PRECISION CO., LTD.
9-3-1
Program Version Number
7-segment display reveals program version number.
9-3-2
7-segment Display Testing
7-segment display reveals “
9-3-3
~
” and “.”.
Keypad & Calibration Switch Testing
Adjust calibration switch to “ON”, and press any key, the corresponding bit will be
→ .
changed from
9-3-4
AD Conversion Value
7-segment display reveals the internal value of the present weight.
9-3-5
EEPROM Testing
Displaying
represents in normal condition.
Displaying
9-3-6
represents in extraordinary condition.
RTC Time & Date Testing
Press
ENTER
key to enter the testing mode, and the screen will display date XX.XX.XX.
Example: “05.11.03” represents 3rd of November, 2005.
Press
ENTER
key again to display time XX.XX.XX.
Example: “09.45.50” represents 9 o’clock, 45 minute and 50 seconds.
9-3-7
RS-232 Serial Output Interface Testing ( OP-01 )
(1) Short the 2 nd pin and 3rd pin of the SER. OUT. D-SUB 9pin socket.
represents in normal condition.
Displaying
Displaying
represents in breakdown condition.
(2) If connected with a computer (protocol must be corresponding), the screen will
display
FM User Manual
~
, which means RS-232 output is in normal condition.
35
SME300000119
Download PDF

advertising