User`s manual | Extron electronic 200, 300C, 300S, 600, 800 Network Card User Manual

User’s Manual
Cable Cubby® 200
Cable Cubby® 300C
Cable Cubby® 300S
Cable Cubby® 600
Cable Cubby® 800
Surface Access Products for Cables, AAPs, and Power Outlets
www.extron.com
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
© 2006 Extron Electronics. All rights reserved.
68-701-01 Rev. F
06 06
Table of Contents
Chapter One • Introduction .................................................... 1-1
About the Cable Cubby® Products ....................................... 1-2
Features ........................................................................................ 1-5
Chapter Two • Installation ...................................................... 2-1
Installation Overview ............................................................... 2-2
Preparing the Routing Template .......................................... 2-3
Preparing the Table ................................................................... 2-4
Preparing the table with a router ......................................... 2-4
Preparing the table with a hole saw
(Cable Cubby 300C only) ....................................................... 2-6
Installing the Cables and AAPs ............................................. 2-7
AAP shelf brackets (CC 300, 600, 800) .................................. 2-7
Installing the power module (CC 300, 600, 800) .................. 2-8
Installing the cables ............................................................... 2-8
Installing the AAPs................................................................. 2-9
Installing the shelf assembly (CC 300, 600, 800) ................ 2-10
Adjusting the cable position (CC 200) ................................ 2-10
Mounting the Cable Cubby .................................................. 2-11
Chapter 3 • Maintenance and Modifications ............. 3-1
Removing and Replacing the Cable Cubby ....................... 3-2
Replacing Cables or an AAP ................................................... 3-5
Adding an Additional Power Module
(CC 600 and CC 800) .................................................................. 3-6
Appendix A • Reference Information..............................A-1
Specifications ..............................................................................A-2
Cable Cubby Part Numbers ....................................................A-7
Included Parts .............................................................................A-8
Replacement/Modification Part Numbers .........................A-9
Routing Template Part Numbers ........................................A-11
Top Plate Dimensions .............................................................A-11
Appendix B • Packaging for Shipment ........................... B-1
Cable Cubby® Products • Table of Contents
i
Table of Contents, cont’d
Cable Cubby® Products
1
Chapter One
Introduction
About the Cable Cubby® Products
Features
68-701-01 Rev. F
06 06
All trademarks mentioned in this manual are the properties of their respective owners.
ii
Cable Cubby® Products • Table of Contents
Introduction
About the Cable Cubby® Products
The Extron Cable Cubbies are furniture-mounted, architectural
solutions for inconspicuous cable access and connection points.
When cables are not in use, they can be stored out of the way
while remaining connected to the presentation system.
Most US/domestic Cable Cubby models provide two
unswitched USA AC power outlets. The US/domestic Cable
Cubby 200 provides one outlet. Each of the international
versions provides a single unswitched AC power outlet
appropriate to the region where the Cable Cubby is sold.
Several different types of power receptacles are available for the
international version, including UK, French, Israeli, Australian,
Indian, European, and Swiss receptacles.
The four different sizes of Cable Cubbies provide room for
the indicated number of Extron’s Architectural Adapter Plates
(AAPs):
•
•
Cable Cubby 800 (international model) — Seven singlespace (single-height) AAPs
•
Cable Cubby 600 USA/domestic model — Six singlespace AAPs
•
Cable Cubby 600 (international model) — Five singlespace AAPs
•
Cable Cubby 300 USA/domestic model — Three singlespace AAPs
•
•
1-2
Cable Cubby 800 USA/domestic model — Eight singlespace (single-height) AAPs

Cable Cubby 300S — Square cover (figure 1-1)

Cable Cubby 300C — Circular (round) cover
Cable Cubby 300 (international model) — Two singlespace AAPs

Cable Cubby 300S — Square cover

Cable Cubby 300C — Circular (round) cover
Figure 1-1 — Cable Cubby 300S US/domestic enclosure
The AAP spaces inside the cubbies allow you to customize the
enclosure to meet your unique needs, with the included split
double space AAPs and Extron’s full line of optional passive
AAPs. The split AAPs can store almost any type of cable
you might encounter. The line of passive AAPs allows you
to customize the AAP with almost any kind of pass-through
connectivity you may need.
The elevation of the AAPs inside the cubby and the arrangement
of the AAPs and the power outlets are adjustable to suit cable
lengths and connector types.
N
The elevation and arrangement of the power outlet
and AAPs in the Cable Cubby 200 are fixed and not
customizable.
Cable Cubby 200 (all models) — Two single-space AAPs
Cable Cubby® Products • Introduction
Cable Cubby® Products • Introduction
1-3
Introduction, cont’d
The installed Cable Cubbies fit nearly flush within a table or
podium top, storing the AAPs and cables out of the way and
out of sight. To access the AAPs and connectors, lift the lid
(figure 1-2). Half-moon cutouts in the lid allow you to run
cables in or out and then close the lid. For Cable Cubby 300s,
600s, and 800s, you can lower the lid into its recessed position.
Extron
Cable Cubby 800
Hideaway Cable
Access Enclosure
Features
•
Easy access to cables and AAPs
•
Durable mechanical movement
•
Cable Cubby 300, 600, and 800 available in a variety of
surface finishes
•
Compact size
•
Flexible installation of Extron passive AAPs
•
Grounded AC receptacle(s)
•
UL/CUL listing
•
CSA certification
15-pin HD Cable
Audio Cable,
Network Cable
Mounted
through a table
or podium
Figure 1-2 — Typical Cable Cubby 800 application
The Cable Cubby 300 is available with either a round or a
rectangular top. The other cubbies all have rectangular tops
only. Preparing the table to install a Cable Cubby 300C (round)
requires simply drilling a hole in the table with a 6-inch hole
saw (figure 1-3). Preparing the table to install a square cubby
requires routing a square hole in the table top. Sheet metal
routing templates are available on request for all models at no
cost.
1
2
3
Figure 1-3 — Cable Cubby 300C mounting
1-4
Cable Cubby® Products • Introduction
Cable Cubby® Products • Introduction
1-5
Introduction, cont’d
Cable Cubby® Products
2
Chapter Two
Installation
Installation Overview
Preparing the Routing Template
Preparing the Table
Installing the Cables and AAPs
Mounting the Cable Cubby
1-6
Cable Cubby® Products • Introduction
Installation
Installation Overview
Preparing the Routing Template
Install and set up the Cable Cubby enclosures as follows:
1
If you plan to use a mounting template that has not been
prepared, prepare the template. See Preparing the Routing
Template, later in this chapter.
2
Cut a hole in the surface where the enclosure will be
installed. See Preparing the Table, later in this chapter.
3
Run all cables necessary to support the AC connector,
the cables stored in the cubby, and all planned AAP
connectors. Leave enough slack in the cables to connect or
route them before the cubby is installed in the table.
4
If applicable, install the power module. If your location
requires electrical conduit, install an Extron flexible
conduit kit. Refer to the Flexible Conduit Kit Installation
Guide, Extron part #68-734-01.
5
Install all desired cables into the cable pass-through (split)
AAPs and install the AAPs into the Cable Cubby. See
Installing the Cables and AAPs, later in this chapter.
6
If applicable, connect cables to the rear connectors on
the passive AAPs and install the AAPs in the cubby. See
Installing the AAPs, later in this chapter.
7
Extron provides metal templates for the Cable Cubbies at no
charge. See Routing Template Part Numbers, in appendix A,
Reference Information, for part numbers. Extron recommends
using this template as a guide to cut the hole in the table where
the cubby will be installed.
N
1.
The metal routing template is reusable. Do not discard
this template when the installation is complete. Save it
for installing Cable Cubby models of the same size.
Cut 1/2" x 4" strips of soft, finished lumber at least
long enough to span the distance between the desired
installation location on the mounting surface and the edges
of the mounting surface (figure 2-1).
These strips raise the routing template above the mounting
surface to provide room for the router’s collar, protect the
mounting surface, and extend the routing template’s reach
so that it can be clamped to the edge of the surface.
C
Do not allow the wood screws to protrude through
the bottom of the wooden strips. Protruding screws
will mar the table when the template is used.
Width of Mou
nting Surface
Mount the Cable Cubby in the table. See Mounting the
Cable Cubby, later in this chapter.
8
Peel the protective film from the top surface.
9
Connect the Cable Cubby power cord.
Mounting
Surface
Edge
Minimum
4 Screws
Wood
Strips
Wood Strip
Height
4" / 10.2 cm
Routing Template
Mounting
Surface
Edge
Wood Thickness
0.5" / 1.3 cm
Figure 2-1 — Prepared CC 300 mounting template
2.
2-2
Cable Cubby® Products • Installation
Using four or more short wood screws, secure the
mounting template to the lumber strips.
Cable Cubby® Products • Installation
2-3
Installation, cont’d
Preparing the Table
The preferred and recommended method for preparing the table
for square Cable Cubbies and one of two preferred methods for
the Cable Cubby 300C is to use the appropriate Extron routing
template and a router.
W
4.
For the Cable Cubby 300C, another preferred method is to use a
6" hole saw.
Wear safety glasses when operating the router.
Failure to comply can result in eye injury.
Using a router with a 5/8" (or 16 mm) outside diameter
guide bushing and a 1/2" (or 12 mm or 12.7 mm) diameter
straight router bit, carefully cut the opening in the surface
(figure 2-2).
Alternatively, for any model, you can use a paper cut-out
template (see appendix A) and a sabre saw or keyhole saw, but
this method is not recommended.
C
The opening in the table for the Cable Cubby should
be cut only by licensed and bonded craftspeople.
Exercise care to prevent scarring or damaging the
furniture.
The surfaces of the Cable Cubby enclosure have
screws and other protruding hardware that could
damage fine furniture. Do not rest the enclosure on
unprotected furniture.
Preparing the table with a router
Prepare the table with a router as follows:
C
C
N
2-4
The routing templates for the various Cable Cubbies
are not interchangeable. If you use the wrong
template, you will cut an improperly-sized hole. If
you use a larger template than required, the cut will
result in gaps in the table surface on either side of
the enclosure.
Figure 2-2 — Cutting the opening with a router
5.
Remove the C-clamps and the routing template.
Ensure that only the wooden strips on the routing
template contact the furniture. Failure to do so may
mar the furniture.
The metal routing template is reusable. Do not discard
the template when the installation is complete. Save it
for installing other Cable Cubbies of the same size.
1.
Locate the desired mounting location on the tabletop or
other installation surface. Mark the location.
2.
Place the mounting template assembly on the table,
centered on the mounting location. Angle the template
for the optimum positioning. If necessary, use a square to
ensure that the template is properly positioned. Extron is
not responsible for improperly positioned Cable Cubbies.
3.
Once the template assembly is positioned properly, secure
the assembly to the table with C-clamps.
Cable Cubby® Products • Installation
Cable Cubby® Products • Installation
2-5
Installation, cont’d
Preparing the table with a hole saw
(Cable Cubby 300C only)
Prepare the table with a hole saw as follows:
1.
On the tabletop or other installation surface, mark the 6"
circle, then find and mark the center of the circle.
W
2.
Wear safety glasses when operating the drill.
Failure to comply can result in eye injury.
Using a portable drill with a 6" (or 152 mm) hole saw,
carefully cut the opening in the table surface at the
desired location (figure 2-3). Extron is not responsible for
improperly positioned Cable Cubbies.
C
Installing the Cables and AAPs
Each Cable Cubby 300, 600, and 800 model ships with one or
two moveable AAP shelf assemblies. The Cable Cubby 200’s
AAP shelf is fixed in place.
AAP shelf brackets (CC 300, 600, 800)
Each shipped AAP shelf assembly consists of a set of shelf
brackets and a number of cable pass-through (split) AAPs.
Depending on the Cable Cubby model, each set of shelf
brackets supports either two, three, or four single-space AAPs
(figure 2-4).
Use a portable drill with sufficient power to handle
the 6” hole saw. Exercise caution when handling
the drill and hole saw. Take care to protect the
mounting surface from damage.
Four-Space Shelf Bracket
and Split AAPs
Three-Space Shelf Bracket
and Split AAPs
Two-Space Shelf Bracket
and Split AAPs
Figure 2-4 — Shelf brackets
Figure 2-3 — Cutting the opening with a hole saw
The simplest way to install the cables and AAPs in the Cable
Cubby 300, 600, and 800 is to populate the shelf brackets with
split and/or standard AAPs outside the cubby and then install
the populated AAP shelf assembly into the cubby.
N
2-6
Cable Cubby® Products • Installation
Cable cubby 300, 600, and 800 only —
On US/domestic models, the power module takes up
two AAP spaces. On IEC, EU, Swiss, UK, Israeli, and
Australian models, the power module takes up three
AAP spaces. Cable pass-through AAPs take two, three,
or four AAP spaces. Consider the arrangement of the
Cable Cubby AAPs when you install them so that you do
not waste AAP space.
Cable Cubby® Products • Installation
2-7
Installation, cont’d
Installing the power module (CC 300, 600, 800)
From the underside of the Cable Cubby, gently push the power
module into the desired position at the desired elevation. Secure
the power module into position with four Phillips head screws.
Installing the cables
Install cables in the channels as follows:
1.
Remove a segment of a set of split AAPs by unscrewing
the nuts on the underside of the bracket that fastens the
plate to the shelf (CC 200) or shelf bracket (CC300, 600, or
800) (figure 2-4, on page 2-7).
2.
Rest the cables in the half-moon cutouts of the split AAP
segment still mounted on the shelf (CC 200) or shelf
brackets (CC 300, 600, and 800). Place the cables so that
the connectors that require inside Cable Cubby access
protrude from the front (black side) of the split AAP
segment.
3.
Insert the screws of the split AAP segment that you
removed in step 1 through the holes in the shelf bracket.
Ensure that the cables are free in the channels that the two
split AAP segments form without being pinched where the
two segments meet.
4.
Secure the split AAP segment to the shelf (CC 200) or shelf
brackets (CC 300, 600, and 800) with the provided captive
washers and #4-40 nuts.
5.
Slip the appropriate size split grommet over each cable
with the flange of the grommet toward the connector
that will be accessible inside the Cable Cubby. Snap the
grommets into the channels.
6.
If applicable, snap the included hole plugs into unused
channels in place of the split grommets.
Three half-moon cutouts in each set of cable pass-through (split)
AAPs loosely channel three cables in the cubby. Each channel
is padded with a split grommet to prevent cable wear. Each
channel and each associated split grommet is a different size
(figure 2-5).
Large
Small
Small
Medium
Medium
Medium
Small
Large
Cable hole
Large
Medium
Small
Large
Hole size
0.625" (1.59 cm)
0.562" (1.43 cm)
0.5" (1.27 cm)
Grommet size
0.453" (1.15 cm)
0.390" (0.99 cm)
0.312" (0.79 cm)
Figure 2-5 — Cable pass-through AAPs
A typical installation consists of a VGA cable, an audio cable,
and a network cable. In a typical installation, the VGA cable
runs in the largest channel, the network cable runs in the middle
(medium) channel, and the audio cable runs in the smaller
channel. In a non-standard installation, just match the diameter
of the cable to the size of the channel as best you can.
2-8
Cable Cubby® Products • Installation
Installing the AAPs
The split AAPs can be replaced with passive Extron AAPs.
Replace a set of split AAPs as follows:
1.
Remove the set of split AAPs to be replaced by unscrewing
the nuts on the underside the shelf (CC 200) or shelf
bracket (CC 300, 600, and 800) that fasten the plates to the
bracket (figure 2-4, on page 2-7).
2.
Cable the rear of the AAP(s) to be installed before attaching
the AAPs to the enclosure.
3.
Insert the screws of the AAPs through the holes in the shelf
or shelf bracket. Secure the AAPs to the shelf brackets with
the provided captive washers and #4-40 nuts.
Cable Cubby® Products • Installation
2-9
Installation, cont’d
3.
Install a second stand-off, in accordance with steps 1 and 2.
From the underside of the Cable Cubby, gently push the AAP
shelf assembly into the desired position at the desired elevation.
Ensure there is enough space above the AAP assembly for the
Cable Cubby lid to close completely. Secure the AAP shelf
assembly into position with four Phillips head screws.
4.
Slide the stand-offs back and forth in the horizontal slots to
position them so that the cables easily rise and lower but
do not fall below the stand-offs.
5.
Tighten the Phillips head screws to lock the stand-offs into
position.
N
6.
Install and position the third stand-off, in accordance with
steps 1 and 2 and 4 and 5 to secure the remaining cables.
Installing the shelf assembly (CC 300, 600, 800)
If the AAP shelf assembly does not slide easily into the
cubby, loosen the AAP mounting nuts. Retighten the
AAP mounting nuts once the AAP shelf assembly is
installed in position.
Adjusting the cable position (CC 200)
The Cable Cubby 200 has three cable stand-offs (figure 2-6) that
allow you to set the height of the cables inside the enclosure.
Adjust the cable height as follows:
Mounting the Cable Cubby
W
The flanged edges of the top of the surface enclosure
are sharp. Exercise caution when the cubby is not
installed in a table to prevent personal injury.
C
The flanged edges of the top of the cubby are
bevelled to an ultra-fine thickness of less than
0.04 (4/100)” (approximately 1 mm). These
edges are soft and can be easily nicked or bent.
Exercise caution when handling and mounting the
enclosure. Mishandling can damage the appearance
of the enclosure.
Cable Stand-Off
1.
Loosen screws to
adjust side to side.
N
2.
Remove screws to
adjust height.
Cable Cubby 300, 600, and 800 — If
screw clamps are installed, remove them
from both sides of the enclosure
(figure 2-7 on page 2-12).
Figure 2-7 shows the installation of
a Cable Cubby 300C. Cable Cubby
300S, 600, and 800 installations are similar.
Remove the plastic strips that protect the corners of the
enclosure and the plastic film on the finished surfaces. If
a sticky residue remains, remove it with an appropriate
metal cleaning product.
C
Figure 2-6 — Cable Cubby 200 height adjustment
2-10
1.
Insert the stand-off into the Cable Cubby and align the
stand-off with one set of horizontal slots in the side of the
enclosure. Choose the adjustment height that best lifts the
cable connectors off of the cable pass-through AAP and
yet still allows the lid to be closed.
2.
Loosely install the Phillips head screws and washers as
shown in figure 2-6.
Cable Cubby® Products • Installation
Do not use isopropyl alcohol or other solvents to
clean the Cable Cubby. Strong solvents will ruin
some finishes.
Cable Cubby® Products • Installation
2-11
Installation, cont’d
3.
Carefully lower the Cable Cubby into the hole to test the
fit. If necessary, remove the enclosure and use a file or rasp
to enlarge or smooth the edges of the opening (figure 2-7).
8.
Cable Cubby 200 — Use the four included 6-32 x 1/2"
screws to fasten the Cable Cubby 200 to the table
(figure 2-8).
15-pin HD Cable
Cable Cubby 300C
Audio Cable
Surface-Mountable
Enclosure for Cables, AAPs &
AC Power Outlet
RJ-45 Cable
Figure 2-8 — Cable Cubby, installation view
Mounting
Surface
Screw Clamp
Figure 2-7 — Cable Cubby 300C, installation view
4.
Cable Cubby 300, 600, and 800 — From the underside of
the table, reinstall the screw clamps on the enclosure at a
height at which the clamp will reach the underside of the
tabletop.
C
2-12
Do not overtighten the Phillips head screws on
the screw clamps. Overtightening can bend the
horizontal flange of the screw clamp.
5.
Cable Cubby 300, 600, and 800 — Snugly tighten the
Phillips head screws on the screw clamps to secure the
enclosure to the surface.
6.
Cable Cubby 300, 600, and 800 — Tighten the locking
thumbscrews on the screw clamps to lock the clamp in
position.
7.
Cable Cubby 200 — Drill 1/8" (3 mm) pilot holes ½"
(12 mm) deep into the table in the mounting holes at each
of the four corners of the cubby.
Cable Cubby® Products • Installation
Cable Cubby® Products • Installation
2-13
Installation, cont’d
Cable Cubby® Products
3
Chapter 3
Maintenance and Modifications
Removing and Replacing the Cable Cubby
Replacing Cables or an AAP
Adding an Additional Power Module (CC 600, CC 800)
2-14
Cable Cubby® Products • Installation
Maintenance and Modifications
The Cable Cubby can be modified in the future to change cables,
to replace an AAP, or to add a second power module. These
modification may require removing the cubby from the table.
Removing and Replacing the Cable Cubby
You may need to remove the cubby from the table in which
it is mounted to replace cables or AAPs, to adjust the height
of the AAP assemblies, or to install a second power module.
Figure 3-1 shows removal of the Cable Cubby 300, 600, or 800
from the table and removal of the AAP shelf assembly and
power module.
N
The Cable Cubby 200 is screwed to the top surface of the
table. Its shelves are fixed in position and not removable.
Remove and replace the Cable Cubby for maintenance as
follows:
W
Ensure that AC power is disconnected before
servicing the Cable Cubby.
1.
Cable Cubby 300, 600, and 800 — Loosen
the locking thumbscrews on the screw
clamps to unlock the clamp (figure 3-1).
2.
Cable Cubby 300, 600, and 800 — Loosen
the screw clamps.
3.
Cable Cubby 300, 600, and 800 —
Remove the screw clamps on both sides of the enclosure.
Extron
Cable Cubby 800
Pins
Screw Clamp
Phillips Head Screw
(Secures AAP Shelf Assembly
and Power Module.)
Figure 3-1 — Removing the cubby and its shelves
3-2
Cable Cubby® Products • Maintenance and Modifications
Cable Cubby® Products • Maintenance and Modifications
3-3
Maintenance and Modifications, cont’d
4.
Cable Cubby 200 — Remove the screws at the four corners
that secure the cubby to the table (figure 3-2).
10.
Cable Cubby 300, 600, and 800 — Snugly tighten the
Phillips head screws on the screw clamps to secure the
enclosure to the surface.
11.
Cable Cubby 300, 600, and 800 — Tighten the locking
thumbscrews on the screw clamps to lock the clamp in
position.
12.
Cable Cubby 200 — Fasten the Cable Cubby 200 to the
table with the four 6-32 x 1/2" screws removed in step 4
(figure 3-2).
Replacing Cables or an AAP
Before you change the cables inside the cubby or replace one or
more AAPs on Cable Cubby 300, 600, and 800 models, you must
remove the AAP shelf assembly from the Cable Cubby. Use the
following guidelines as applicable:
1
Cable Cubby 300, 600, and 800 — If the Phillips head
screws on the front and rear of the cubby are blocked by
the table, remove the cubby from the table. See Removing
and Replacing the Cable Cubby, steps 1 through 4, earlier in
this chapter.
2
Cable Cubby 300, 600, and 800 — Remove the AAP shelf
assembly(s) by removing the four Phillips head screws on
the front and rear of the Cable Cubby and gently pushing
the assembly out through the bottom of the cubby.
3
Change the cables and/or AAPs the same way you
installed them. See Installing the Cables and AAPs in
chapter 2, Installation.
4
Cable Cubby 300, 600, and 800 — If you removed
the cubby from the table, reinstall the surface mount
enclosure. See Removing and Replacing the Cubby, steps 8
through 11, earlier in this chapter.
Figure 3-2 — Removing the Cable Cubby 200
5.
Lift the enclosure from the table.
W
The flanged edges of the top of the surface enclosure
are sharp. Exercise caution when the cubby is not
installed in a table to prevent personal injury.
C
The flanged edges of the top of the cubby are
bevelled to an ultra-fine thickness of less than
0.04 (4/100)" (approximately 1 mm). These
edges are soft and can be easily nicked or bent.
Exercise caution when handling and mounting the
enclosure. Mishandling can damage the appearance
of the enclosure.
6.
Remove the AAP shelf assembly(s) or power module by
removing the four Phillips head screws on the front and
rear of the Cable Cubby and gently pushing the assembly
out through the bottom of the cubby.
7
Perform the desired maintenance procedure.
8.
Carefully lower the Cable Cubby into the hole in the table.
9.
Cable Cubby 300, 600, and 800 — From the underside of
the table, reinstall the screw clamps on the enclosure at a
height at which the clamp will reach the underside of the
tabletop.
C
3-4
Do not overtighten the Phillips head screws on
the screw clamps. Overtightening can bend the
horizontal flange of the screw clamp
Cable Cubby® Products • Maintenance and Modifications
Cable Cubby® Products • Maintenance and Modifications
3-5
Maintenance and Modifications, cont’d
Figure 3-4 shows typical configurations before and after
you add a second power module to an international
Cable Cubby 800.
Adding an Additional Power Module
(CC 600 and CC 800)
Each additional power module occupies two (USA/domestic
models) or three (international models) of the cubby’s AAP
spaces, reducing the amount of AAP space available in the
cubby for cable pass through (split) or passive AAPs. Use the
following guidelines as applicable:
1
Replacement two-space, three-space, and four-space shelf
brackets and cable pass-through (split) AAPs are available
from Extron, and may be required to maximize the
remaining available space if you add a power module.
•
Cable Cubby 200 models — Adding a second power
module is not possible.
•
Cable Cubby 300 models — Adding a second power
module is not recommended. Depending on the
model, with a second power module, there is room
left for either only a single one-space AAP or no AAP
space left at all.
•
After
Before
UNSWITCHED
Three AAP
Space Shelf
UNSWITCHED
230~50/60Hz
5A
Four AAP
Space Shelf
230~50/60Hz
5A
UNSWITCHED
230~50/60Hz
5A
Four AAP
Space Shelf
Figure 3-4 — International Cable Cubby 800 with
second power module
Cable Cubby 600 and 800 international models — In
general, you probably do not need replacement shelf
brackets when you add an international module to
an international Cable Cubby, because the power
module replaces a three-space shelf that is standard
in all international cubbies.
Figure 3-3 shows typical configurations before and after
you add a second power module to an international
Cable Cubby 600.
After
Before
UNSWITCHED
Two AAP
Space Shelf
230~50/60Hz
5A
Three AAP
Space Shelf
UNSWITCHED
230~50/60Hz
5A
UNSWITCHED
230~50/60Hz
5A
Two AAP
Space Shelf
Figure 3-3 — International Cable Cubby 600 with
second power module
3-6
Cable Cubby® Products • Maintenance and Modifications
Cable Cubby® Products • Maintenance and Modifications
3-7
Maintenance and Modifications, cont’d
Cable Cubby 600 and 800 US/Domestic models —
You probably do need replacement shelf brackets
when you add a US/Domestic power module to
a US/Domestic Cable Cubby, because the power
module takes up two spaces in a cubby that, in its
standard configuration, is equipped with three-space
(Cable Cubby 600) or four-space (Cable Cubby 800)
shelves.
Figure 3-6 shows typical configurations before and after
you add a second US/Domestic power module to a
US/domestic Cable Cubby 800 and suggests rack shelf
configurations to replace the lost shelf space.
After
Before
Figure 3-5 shows typical configurations before and after
you add a second US/Domestic power module to a
US/domestic Cable Cubby 600 and suggests rack shelf
configurations to replace the shelf space removed.
UNSWITCHED
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
100-240V/ 5AMAX
UNSWITCHED
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
100-240V/ 5AMAX
After
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
100-240V/ 5AMAX
UNSWITCHED
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
100-240V/ 5AMAX
Four AAP
Space Shelf
Four AAP
Space Shelf
Two AAP
Space Shelf
Four AAP
Space Shelf
or
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
AUDIO
Four AAP
Space Shelf
VIDEO
Three AAP
Space Shelf
VIDEO
Three AAP
Space Shelf
L
AUDIO
R
UNSWITCHED
R
Before
L
•
or
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
UNSWITCHED
UNSWITCHED
100-240V/ 5AMAX
100-240V/ 5AMAX
Two AAP
Space Shelf
Cable Cubby® Products • Maintenance and Modifications
Three AAP
Space Shelf
Figure 3-6 — Cable Cubby 800 with second power
module
2
If the Phillips head screws on the front and rear of the
cubby are blocked by the table, remove the cubby from the
table. See Removing and Replacing the Cable Cubby, steps 1
through 4, earlier in this chapter.
3
Before you add an additional power module, you must
make room for the Cable Cubby by eliminating two
or three AAP spaces and the AAP shelf brackets that
support them. Remove the Phillips head screws on the
front and rear of the Cable Cubby and gently pushing the
assembly(s) out through the bottom of the cubby.
Two AAP
Space Shelf
Figure 3-5 — Cable Cubby 600 with second power
module
3-8
Three AAP
Space Shelf
Cable Cubby® Products • Maintenance and Modifications
3-9
Maintenance and Modifications, cont’d
4
From the underside of the Cable Cubby, gently push the
additional power module into the desired position at the
desired elevation. Secure the power module into position
with the included four Phillips head screws (figure 3-7).
Extron
Cable Cubby 600
2 Screws ea. side
Cable Cubby® Products
A
Appendix A
Figure 3-7 — Installing the power module
5
6
If desired, assemble and install replacement AAP shelf
assemblies. Remember that the cable pull function of the
Cable Cubby requires at least two AAPs. See Installing the
Cables and AAPs in chapter 2, Installation.
If you removed the cubby from the table, reinstall the
surface mount enclosure. See Removing and Replacing the
Cable Cubby, steps 8 through 11, earlier in this chapter.
Reference Information
Specifications
Cable Cubby Part Numbers
Included Parts
Replacement/Modification Part Numbers
Routing Template Part Numbers
Top Plate Dimensions
3-10
Cable Cubby® Products • Maintenance and Modifications
Reference Information
Specifications
d
General
Rack mount .................................... No, but furniture mountable
Enclosure type .............................. Metal
H
H
Enclosure dimensions
C
N
Use the appropriate metal Extron routing template or refer to
the surface cutout dimensions here before cutting a hole in the
furniture or other surface. Pay special attention to the direction
the unit will face; the unit’s AAP and connector access side
is underlined. Extron is not responsible for miscut mounting
holes.
Architectural Adapter Plates (AAPs) are shown in the diagrams
that follow and in photographs as examples only. AAPs are
optional accessories for the Cable Cubby products. AAPs and
cables must be ordered separately.
H
W
D
Cable Cubby 200
Cable Cubby 200
Top plate (outer rim)....................
8.000" W x 4.394" D
(20.32 cm W x 11.16 cm D)
Surface cutout (inside rim) ......... 7.185 ±0.0325" W x 3.155 ±0.0325" D
(18.25 ±0.083 cm W x 8.01 ±0.083 cm D)
Box (under surface) ..................... 4.000" H x 7.120" W (front/rear of
unit) x 2.974" D
(10.16 cm H x 18.08 cm W x 7.55 cm D)
A-2
Cable Cubby® Products • Reference Information
W
D
Cable Cubby 300S
W
D
Cable Cubby 300C
Cable Cubby 300S
Top plate (outer rim)....................
5.130" W x 6.470" D
(13.0 cm W x 16.4 cm D)
Surface cutout (inside rim) ........ 4.625 ±0.0325" W x 5.970 ±0.0325" D
(11.75 ±0.083 cm W x 15.16 ±0.083 cm D)
Box (under surface) ..................... 6.410" H x 4.320" W (front/rear of
unit) x 4.750" D without clamps
(16.28 cm H x 10.97 cm W x 12.07 cm D)
without clamps
6.410" H x 6.57" W x 4.750" D with
clamps
(16.28 cm H x 16.68 cm W x 12.07 cm D
with clamps
Cable Cubby 300C
Top plate (outer rim) ................... 6.500" (16.51 cm) diameter circle
Surface cutout (inside rim) ......... 6.000 ±0.0325"
(15.24 ±0.083 cm) diameter circle
Box (under surface) ..................... 6.410" H x 4.320" W (front/rear of
unit) x 4.750" D without clamps
(16.28 cm H x 10.97 cm W x 12.07 cm D)
without clamps
6.410" H x 6.57" W x 4.750" D with
clamps
(16.28 cm H x 16.68 cm W x 12.07 cm D)
with clamps
Cable Cubby® Products • Reference Information
A-3
Packaging for Shipment, cont’d
H
H
W
D
Cable Cubby 600
Cable Cubby 600
Top plate (outer rim) ...................
6.960" W x 6.960" D
(17.68 cm W x 17.68 cm D)
Surface cutout (inside rim) ......... 6.460 ±0.0325" W x 6.460 ±0.0325" D
(16.41 ±0.083 cm W x 16.41 ±0.083 cm D)
Box (under surface) ..................... 6.410” H x 6.400" W (front/rear of
unit) x 4.750" D without clamps
(16.28 cm H x 16.26 cm W x 12.07 cm D)
without clamps
6.410" H x 8.67" W x 4.750" D with
clamps
(16.28 cm H x 22.02 cm W x 12.07 cm D)
with clamps
A-4
Cable Cubby® Products • Packaging for Shipment
W
D
Cable Cubby 800
Cable Cubby 800
Top plate (outer rim) ...................
8.360" W x 6.820" D
(21.23 cm W x 17.32 cm D)
Surface cutout (inside rim) ........ 7.860 ±0.0325" W x 6.320 ±0.0325" D
(19.96 ±0.083 cm W x 16.05 ±0.083 cm D)
Box (under surface) ..................... 6.410" H x 7.800" W (front/rear of
unit) x 4.750" D without clamps
(16.28 cm H x 19.81 cm W x 12.07 cm D)
without clamps
6.410" H x 10.07" W x 4.750" D with
clamps
(16.28 cm H x 25.58 cm W x 12.07 cm D)
with clamps
Cable AAP cable hole diameters
Large cable hole ................. 0.63" (1.60 cm)
Large grommet .................. 0.45" (1.14 cm)
Medium cable hole............ 0.56" (1.42 cm)
Medium grommet ............. 0.39" (0.99 cm)
Small cable hole ................. 0.50" (1.27 cm)
Small grommet .................. 0.31" (0.79 cm)
Product weight
Cable Cubby 200 ................ 2.5 lbs (1.1 kg)
Cable Cubby 300S/300C .. 5.0 lbs (2.3 kg)
Cable Cubby 600................ 9.0 lbs (4.1 kg)
Cable Cubby 800................ 13.0 lbs (5.9 kg)
Cable Cubby® Products • Packaging for Shipment
A-5
Packaging for Shipment, cont’d
Shipping weight
Cable Cubby 200 ................
Cable Cubby 300S .............
Cable Cubby 300C .............
Cable Cubby 600................
Cable Cubby 800................
Vibration ........................................
4 lbs (2 kg)
8 lbs (4 kg)
8 lbs (4 kg)
12 lbs (6 kg)
15 lbs (7 kg)
ISTA 1A in carton
(International Safe Transit Association)
Listings, certifications ................... UL, CUL, CSA C/US
Compliances................................... CE
Warranty ........................................ 3 years parts and labor
N
Specifications are subject to change without notice.
Cable Cubby Part Numbers
Cable Cubby 200
Part number
Cable Cubby 200 US/domestic (powder coat finish)
60-716-01
Cable Cubby 200S international (powder coat finish)
60-717-nn
Cable Cubby 300S
Part number
Cable Cubby 300S US/domestic (black anodized finish)
60-526-01
Cable Cubby 300S international
60-712-nn
Cable Cubby 300C
Part number
Cable Cubby 300C/domestic (black anodized finish)
60-527-01
Cable Cubby 300C international
60-713-nn
Cable Cubby 600
Part number
Cable Cubby 600 US/domestic (black anodized finish)
60-525-01
Cable Cubby 600 international
60-714-nn
Cable Cubby 800
A-6
Cable Cubby® Products • Packaging for Shipment
Part number
Cable Cubby 800 US/domestic (black anodized finish)
60-524-01
Cable Cubby 800 international
60-715-nn
N
For the international versions, the nn in the part number
identifies the AC power connector and finish (black
anodized, brushed aluminum, polished aluminum, and
brushed brass). Specify the desired power connector and
finish when ordering.
N
All Cable Cubby 200 models are available in a powder
coat finsh only.
N
The USA versions of the Cable Cubby 300, 600, and
800 are also available in brushed aluminum, polished
aluminum, and brushed brass finishes. Visit the Extron
web site, www.extron.com for more part numbers.
Cable Cubby® Products • Packaging for Shipment
A-7
Packaging for Shipment, cont’d
Included Parts
Replacement/Modification Part Numbers
®
The Cable Cubby includes the Cable Cubby Products
manual and a selection of shelf brackets, cable pass through
AAPs, grommets, and hole plugs that vary depending on the
Cable Cubby model. See the table below for included parts:
Power modules (CC 300, 600, 800)
Large
Small
Small
Medium
Medium
Medium
Part number
Cable Cubby AC power module–USA
70-261-01
Cable Cubby AC power module–Swiss
70-262-01
Cable Cubby AC power module–Israel
70-388-01
Cable Cubby AC power module–Europe
70-264-01
Cable Cubby AC power module–Australia
70-265-01
Cable Cubby AC power module–UK
70-266-01
Cable Cubby AC power module–France
70-389-01
Cable Cubby AC power module–India
70-390-01
Small
Large
Cable pass-through AAPs
Large
Part number
N Each AAP cable pass-through kit listed below includes three
grommets; one large, one medium, and one small.
AAP Cable
Pass Through
Left
AAP Cable
Pass Through
Left Middle
AAP Cable
Pass Through
Right Middle
AAP Cable
Pass Through
Right
AAP Shelf brackets Pass through AAPs* Grommets
L L-M R-M R
Model
2 Pos. 3. Pos 4. Pos
L M S
0
0
1 1 1
0✫
CC 200 US
1
0
0
1
0
0
1 1 1
CC 200 Int.
0✫
1
0
0
1
❖
0
2
0
2 2 2
CC 300 US
2
1
0
0
2
0
0
1 1 1
CC 300❖ Int.
1
0
0
1
0
4
0
5 5 5
CC 600 US
1
2
2
1
2
2
0
4 4 4
CC 600 Int.
2
2
1
0
0
0
4
7 7 7
CC 800 US
1
3
3
1
0
2
2
6 6 6
CC 800 Int.
2
3
2
0
* L = left, L-M = left-middle, R-M = right midle, R = right
✝ L = large, M = medium, S = small
✫ Fixed two position shelf incorporated into the enclosure
❖ CC 300 S and CC 300 C have the same AAP configuration
✝
✝
Plugs
L M S
1 1 1
1 1 1
2 2 2
1 1 1
5 5 5
4 4 4
7 7 7
6 6 6
AAP cable pass through (right) (figure A-1)
70-267-01
AAP cable pass through (right-middle) (figure A-1)
70-268-01
AAP cable pass through (left-middle) (figure A-1)
70-269-01
AAP cable pass through (left) (figure A-1)
70-270-01
Large
Small
Small
Medium
Medium
Medium
Small
Large
AAP Cable
Pass Through
Left
AAP Cable
Pass Through
Left Middle
Large
AAP Cable
Pass Through
Right Middle
AAP Cable
Pass Through
Right
Figure A-1 — Cable pass through AAPs
A-8
Cable Cubby® Products • Packaging for Shipment
Cable Cubby® Products • Packaging for Shipment
A-9
Packaging for Shipment, cont’d
AAP shelf brackets (CC 300, 600, 800)
Part number
Routing Template Part Numbers
The following reuseable sheet metal routing templates are
recommended for installation and are available at no charge.
Four-space AAP Cable Cubby bracket (set of 2) (figure A-2)
70-273-01
Three-space AAP Cable Cubby bracket (set of 2) (figure A-2)
70-272-01
Two-space AAP Cable Cubby bracket (set of 2) (figure A-2)
70-271-01
Template
Single-space AAP Cable Cubby bracket (set of 2) (figure A-2)
70-392-01
Cable Cubby 200 routing template
70-384-01
Cable Cubby 300S/300C routing template
70-237-01
Cable Cubby 600 routing template
70-239-01
Cable Cubby 800 routing template
70-240-01
Part number
Top Plate Dimensions
There are two preferred and recommended methods for cutting
the table: either use the appropriate metal routing template
(figure A-3 and chapter 2, Installation) and a router or use a
hole saw (Cable Cubby 300C only). The templates (see Routing
Template Part Numbers, for part numbers) are available at no cost.
Four-Space Shelf Bracket
and Split AAPs
Three-Space Shelf Bracket
and Split AAPs
Two-Space Shelf Bracket
and Split AAPs
Figure A-2 — Shelf brackets
CABLE CUBBY 300
USER ACCESS
Grommet and plug kit
Part number
N The kit listed below includes three grommets; one large, one medium,
and one small.
Grommet and hole plug kit
70-387-01
HSA 200
USER ACCESS
HSA 200
CABLE CUBBY 300
Figure A-3 — CC 300S/300C metal routing template
If you choose not to use Extron’s metal routing templates, the
cut-out templates (figure A-4, figure A-5, figure A-6, figure A-7,
and figure A-8) will help you properly prepare the mounting
surface. The cutout templates are not to scale and are for
reference only. The surface cut-out area dimensions for the
template are marked in bold type.
For full size paper templates, visit the Extron Web site
(http://www.extron.com) or call the Extron S3 Sales & Technical
Support Hotline.
A-10
Cable Cubby® Products • Packaging for Shipment
Cable Cubby® Products • Packaging for Shipment
A-11
Packaging for Shipment, cont’d
Cut-Out Template for Extron's
Cut-Out Template for Extron's
Cable Cubby 200
Cable Cubby 300S
5.130" (13.0 cm)
4.394" (11.16 cm)
.350" (1.90 cm)
4.625 + 0.0325"
(11.75 + 0.083 cm)
3.155 + 0.0325"
(8.01 + 0.083 cm)
6.470"
(16.4 cm)
User Access
SURFACE CUT-OUT
AREA = 3.155 + 0.0325"
SURFACE CUT-OUT
AREA = 4.625 + 0.0325"
+
5.970" (11.75 cm) x 5.970 0.0325"
+
(15.16 0.083 cm)
(15.2 cm)
(8.01 + 0.083 cm)
x 7.185 + 0.0325"
(18.25 + 0.083 cm)
8.00
(20.32
7.185 + 0.0325"
(18.25 + 0.083 cm)
0.5"
(1.3 cm)
Cut surface material
out along this line.
Top Panel
Cut-Out Radius:
0.25"
(0.6 cm)
User Access
TEMPLATE IS NOT FULL SIZE.
0.5"
(1.3 cm)
Top Panel
Cut surface material
out along this line.
.350" (1.90 c
Cut-Out Radius:
0.25"
(0.6 cm)
Figure A-5 — Cable Cubby 300S cut-out template
Figure A-4 — Cable Cubby 200 cut-out template
A-12
Cable Cubby® Products • Packaging for Shipment
Cable Cubby® Products • Packaging for Shipment
A-13
Packaging for Shipment, cont’d
Cut-Out Template for Extron's
Cut-Out Template for Extron's
Cable Cubby 300C
Cable Cubby 600
6.960" (17.68 cm)
6.460 + 0.0325"
(16.41 + 0.083 cm)
6.500" Dia.
(16.51 cm)
6.960"
(17.68 cm)
6.000 + 0.0325" Dia.
(15.24 + 0.083cm)
6.460 + 0.0325"
(16.41 + 0.083 cm)
SURFACE CUT-OUT
AREA = 6.460 + 0.0325"(16.41 + 0.083 cm) x
6.460 + 0.0325"(16.41 + 0.083 cm)
SURFACE CUT-OUT
AREA = 6.000 + 0.0325" Dia.
(15.24 + 0.083cm)
0.5"
(1.3 cm)
Cut surface material
out along this line.
Top Panel
Cut-Out Radius:
0.25"
(0.6 cm)
User Access
User Access
TEMPLATE IS NOT FULL SIZE.
TEMPLATE IS NOT FULL SIZE.
Figure A-7 — Cable Cubby 600 cut-out template
Figure A-6 — Cable Cubby 300C cut-out template
A-14
Cable Cubby® Products • Packaging for Shipment
Cable Cubby® Products • Packaging for Shipment
A-15
Packaging for Shipment, cont’d
Cut-Out Template for Extron's
Cable Cubby® Products
Cable Cubby 800
8.360" (21.23 cm)
7.860 + 0.0325"
(19.96 + 0.083 cm)
6.820"
(17.32 cm)
6.320 + 0.0325"
(16.05 + 0.083 cm)
SURFACE CUT-OUT
AREA = 7.860 + 0.0325"(19.96 + 0.083 cm) x
6.320 + 0.0325"(16.05 + 0.083 cm)
B
Appendix B
0.5"
(1.3 cm)
Cut surface material
out along this line.
Top Panel
Cut-Out Radius:
0.25"
(0.6 cm)
User Access
TEMPLATE IS NOT FULL SIZE.
Figure A-8 — Cable Cubby 800 cut-out template
A-16
Cable Cubby® Products • Packaging for Shipment
Packaging for Shipment
Packaging for Shipment
The Cable Cubby’s ultra-fine machined surfaces and moving
parts make them vulnerable to damage caused by mishandling
during shipment if they are improperly packaged. If, for any
reason, you need to return a Cable Cubby to Extron, first contact
Extron to obtain a return kit. The return kit, which reduces the
chances of damage during shipment, includes a sturdy shipping
carton and foam that can be fitted to each Cable Cubby model
(figure B-1).
2.
Disconnect and retain all cables, remove and retain the
AAP shelf assembly(s) (CC 300, 600, 800) and remove
the Cable Cubby from the table or desk. See Removing
and Replacing the Cubby, steps 1 through 4, in chapter 3,
Maintenance and Modifications.
N
3.
For Cable Cubby 300, 600, and 800 models, retain the
screw clamps.
Install the plastic strips that protect the flanged edges of
the top of the surface enclosure (figure B-2).
Figure B-1 — Cable Cubby return kit
Package a Cable Cubby for shipment as follows:
1.
Contact the Extron S3 Sales & Technical Support Hotline to
obtain a return kit. Extron will send the return kit to the
location you specify.
W
C
B-2
The flanged edges of the top of the surface enclosure
are sharp when the Cable Cubby is removed from
the table. Exercise caution when handling to
prevent personal injury.
The flanged edges of the top of the surface enclosure
are bevelled to an ultra-fine thickness of less than
0.04 (4/100)” (approximately 1 mm). These
edges are soft and can be easily nicked or bent.
Exercise caution when handling and mounting the
enclosure. Mishandling can damage the appearance
of the enclosure.
Cable Cubby® Products • Packaging for Shipment
Figure B-2 — Installing protective strips
N
For Cable Cubby 200 models proceed to step 13.
For Cable Cubby 300, 600, and 800 models, continue to
step 4, below.
4.
Remove and retain the top foam pad from the carton.
5.
CC 300, 600, 800 only — Remove and discard the center
foam section of the cushion in the carton (figure B-3). If
you are returning a Cable Cubby 300 model, this is the
correct fit. Proceed to step 8.
Cable Cubby® Products • Packaging for Shipment
B-3
Packaging for Shipment, cont’d
Figure B-5 — Removing outer side foams
Figure B-3 — Removing center foam
8.
6.
CC 600, 800 only — Remove and discard the inner side
foam sections of the cushion in the carton (figure B-4). If
you are returning a Cable Cubby 600 model, this is the
correct fit. Proceed to step 8.
Figure B-4 — Removing inner side foams
7.
B-4
CC 800 only — Remove and discard the outer side foam
sections of the cushion in the carton (figure B-5). This is
the correct fit for a Cable Cubby 800 model. Proceed to
step 8.
Cable Cubby® Products • Packaging for Shipment
If you will not install a replacement Cable Cubby in this
location, remove and retain one of the small foam sections
to the front or rear of the cubby opening in the cushion in
the carton (figure B-6).
Figure B-6 — Removing screw clamp area foam
9.
CC 300, 600, 800 only — Place the two screw clamps from
step 2 into the screw clamp opening in the foam cushion in
the carton.
Cable Cubby® Products • Packaging for Shipment
B-5
Packaging for Shipment, cont’d
10.
CC 300, 600, 800 only — Stuff the foam section removed in
step 8 into the screw clamp opening in the foam cushion in
the carton.
11.
CC 300, 600, 800 only — Lower the Cable Cubby, with the
top closed, into the foam cushion in the shipping carton
(figure B-7).
13.
CC 200 only — Lower the Cable Cubby and foam into the
shipping carton.
14.
Place the top foam pad, removed in step 4, on top of the
Cable Cubby.
15.
Close the shipping carton and seal it with high quality
shipping tape.
16.
Ship the Cable Cubby to Extron using a reputable shipping
company.
Figure B-7 — Placing the cubby in the carton
12.
CC 200 only — Insert the Cable Cubby 200 into the foam
shell (figure B-8). Firmly push the Cable Cubby into the
foam shell to completely suspend the Cable Cubby.
Figure B-8 — Installing the foam shell
B-6
Cable Cubby® Products • Packaging for Shipment
Cable Cubby® Products • Packaging for Shipment
B-7
Packaging for Shipment, cont’d
B-8
Cable Cubby® Products • Packaging for Shipment
Cable Cubby® Products • Packaging for Shipment
B-9
Packaging for Shipment
B-10
Cable Cubby® Products • Packaging for Shipment
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Extron’s Warranty
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Download PDF

advertising