User`s manual | Extron electronic DVI 201 Rx Stereo Receiver User Manual

User’s Manual
DVI 201 Tx/Rx
Digital Video Transmitter and Receiver
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Dubai
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2008 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-1034-02 Rev. B
08 08
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Extron’s Warranty
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics 1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Table of Contents
Chapter One • Introduction..................................................... 1-1
About this Manual..................................................................... 1-2
About the DVI 201 Transmitters and Receivers................ 1-2
TP cable advantages............................................................... 1-4
Control communications........................................................ 1-4
Transmission distance............................................................. 1-4
Features......................................................................................... 1-5
Chapter Two • Installation and Operation. .................. 2-1
Mounting the Tx/Rx.................................................................. 2-2
Non-Decora unit mounting.................................................... 2-2
Tabletop placement............................................................ 2-2
Rack mounting. .................................................................. 2-2
Under-furniture mounting.................................................. 2-4
Through-furniture mounting.............................................. 2-5
Projector mounting. ........................................................... 2-6
Decora unit mounting.......................................................... 2-11
UL/Safety Requirements................................................... 2-11
Preparing the site and installing the wall box. ................ 2-11
Final installation............................................................... 2-14
Connections................................................................................ 2-15
Transmitter connections....................................................... 2-15
Receiver connections............................................................ 2-19
Pin assignments and wiring................................................. 2-22
DVI connector pin assignments........................................ 2-22
TP cable termination......................................................... 2-23
Power supply wiring. ....................................................... 2-25
RS-232 connector wiring. ................................................. 2-26
Operation.................................................................................... 2-27
Transmitter control and indicator........................................ 2-29
Receiver indicator................................................................. 2-29
System operation.................................................................. 2-29
Technical Points for Digital Video and Content
Protection Encryption............................................................. 2-30
Troubleshooting........................................................................ 2-31
Application Examples. ............................................................ 2-32
Audio conversion.................................................................. 2-32
Modulated IR pass through.................................................. 2-33
DVI 201 Tx/Rx • Table of Contents
i
Table of Contents, cont’d
Appendix A • Reference Information..............................A-1
Specifications...............................................................................A-2
Part Numbers...............................................................................A-6
Transmitter/receiver pair part numbers................................A-6
Included parts.........................................................................A-6
Mounting accessories.............................................................A-7
Cables......................................................................................A-8
Adapters..................................................................................A-8
Decora Template Dimensions.................................................A-9
DVI 201 Tx/Rx
1
Chapter One
Introduction
About this Manual
About the DVI 201 Transmitters and Receivers
Features
68-1034-02 Rev. B
08 08
All trademarks mentioned in this manual are the properties of their respective owners.
ii
DVI 201 Tx/Rx • Table of Contents
Introduction
About this Manual
There are two subsets of transmitters and receivers in two
different enclosures or form factors:
This manual contains information about the Extron
DVI 201 family of Digital Visual Interface (DVI) video
transmitters (Tx) and receivers (Rx), including how to install,
operate, and configure them.
•
About the DVI 201 Transmitters and Receivers
DVI 201 Tx/Rx — These units are housed in quarter rack
width metal enclosures. They can be set on a tabletop
or mounted in a rack, under or through furniture, or to a
projector pole. The transmitter in this form factor has a
local monitor output.
N
The Extron DVI 201 is a family of DVI transmitters and
receivers, in enclosures that support different mounting options.
A transmitter and receiver pair extends the usable distance of
DVI digital video and RS-232 control signals over two Category
(CAT) 5/5e/6 unshielded twisted pair (UTP) or shielded twisted
pair (STP) cables. The DVI 201 A D transmitter and receiver also
route audio, but not on the TP link. The video and control (and
audio, if applicable) signals can be transmitted up to 200' (60 m).
•
The non-Decora® models do not input, transmit, receive,
or output audio.
DVI 201 A D Tx/Rx — These units are housed in
enclosures that can be mounted in UL standard wall boxes
with Decora-style face plates. These units also convert
computer level audio to balanced or unbalanced stereo
audio.
N
• A non-Decora transmitter or receiver is partially
compatible with a Decora receiver or transmitter.
• A mixed form factor system can transmit and receive
video and RS-232 communications.
UT
UTP
LO
CA
LO
Extron
DVI 201 Tx
T
PU
00
I2
DV
TX
S
RIE
CAT 5/5e/6/7 UTP up to 200’
• A mixed form factor system cannot handle audio,
as the non-Decora models do not input, transmit,
receive, or output audio.
SE
IN
DV
Extron
DVI 201 Rx
Transmitter
Receiver
RS-232
Control
DVI Cable
-232RU
RS TH
I
DV
0
20
Rx
RS-232
Multimedia
PC
Projector
Figure 1-1 — Typical transmitter and receiver application
A DVI 201 system consists of a transmitter (Tx) and a receiver
(Rx). The pair can handle a single link of DVI-D digital video
and a bi-directional RS-232 link. The DVI 201 A D also converts
a computer audio input into balanced or unbalanced stereo
audio output.
1-2
DVI 201 Tx/Rx • Introduction
Receivers
Tx
Transmitters
SS
PA
DVI 201 Tx
non-Decora
Transmitters
Receivers
DVI 201 Tx DVI 201 A D Tx DVI 201 Rx DVI 201 A D Rx
non-Decora Decora
non-Decora Decora
DVI video DVI video
Control
Control
DVI video
Control
DVI 201 A D Tx
non-Decora
DVI 201 Rx
non-Decora
DVI video
Control
DVI video
Control
DVI 201 A D Rx
non-Decora
DVI video
Control
DVI video
Control
Audio (pass)
DVI video
Control
Audio (pass)
The units can be purchased as a pair (of the same form factor)
or individually. Each purchased pair and each individual
transmitter is shipped with a single external desktop 12 VDC
power supply that accepts 100 to 240 VAC, 50 Hz or 60 Hz input.
A single power supply connected to either the transmitter or the
receiver can power both units through one of the TP cables that
link the units.
DVI 201 Tx/Rx • Introduction
1-3
Introduction, cont’d
N
In this manual, the terms "DVI 201," "DVI 201 Tx,"
"DVI 201 Rx," "transmitter," and "receiver" refer to the
applicable unit(s) in either form factor, unless otherwise
specified.
TP cable advantages
Twisted pair cable is much smaller, lighter, more flexible, and
less expensive than coaxial or DVI cable. These transmitter and
receiver twisted pair (TP) products make cable runs simpler
and less cumbersome. Termination of the cable with RJ-45
connectors is simple, quick, and economical.
N
The transmitter and receiver pair works with unshielded
twisted pair (UTP) or shielded twisted pair (STP)
cables; but, to ensure FCC Class A and CE compliance,
STP cables are recommended.
N
Do not use Extron’s UTP23SF-4 Enhanced SkewFree™ A/V UTP cable to link the transmitter and
receiver. Skew-free A/V cable was designed for most
Extron TP transmitter/receiver applications, but the
DVI 201 Tx/Rx does not work properly with this cable.
Control communications
The RS-232 and/or infrared (IR) communications are via a
passive pass-through only; the transmitter and receiver do not
generate or respond to these signals.
Transmission distance
The maximum transmission distance is determined by the
resolution of the signal and the TP cable that is used.
With CAT 5/5e/6/7 UTP cable, the Tx/Rx pair can transmit
and receive 720p and 1080i HDTV or XGA video signals up to
200' (60 m) and 1080p HDTV or UXGA video up to 100' (30 m).
With CAT 5/5e/6/7 STP cable, the Tx/Rx pair can transmit
and receive 720p and 1080i HDTV or XGA video signals up to
200' (60 m) and 1080p HDTV or UXGA video up to 125' (38 m).
N
The transmission distance varies greatly, depending on
the signal resolution, type of cable used, graphics card,
and display used in the system.
Features
Transmits single link DVI-D signals over two CAT 5/5e/6
cables — Standard twisted pair cables provide an
economical, easily installed cable solution.
Long distance transmission —
CAT 5/5e/6/7 UTP cable — Accommodates 720p
and 1080i HDTV or XGA video over 200' (60 m), and
1080p HDTV or UXGA (1600 x 1200) over 100' (30 m).
CAT 5/5e/6/7 STP cable — Accommodates 720p and
1080i HDTV or XGA video over 200' (60 m), and
1080p HDTV or UXGA (1600 x 1200) over 125' (38 m).
Local monitor output (DVI 201 Tx [non-Decora] only) —
The DVI 201 Tx transmitter features a DVI-D output for
connection to a local monitor.
Supports DDC and HDCP copy protection transmission —
The Tx/Rx pairs fully support long distance transmission
of the DDC and HDCP signals.
DDC routing to local or remote display — At the DVI 201 Tx
[non-Decora], the DDC or HDCP signal is directed to
either the local display or the remote display, depending
on which is more critical in receiving the signal.
Remote powering of transmitter or receiver — Only one power
supply is necessary to power both devices.
Control communications pass-through — Bidirectional RS-232
or IR control signals can be transmitted alongside the
DVI or HDMI signal, so that the remote display can be
controlled without the need for additional cabling.
Audio routing — The DVI 201 A D Tx/Rx also routes
unbalanced stereo audio, when both units are the Decora
form factor.
Supports CEC signal transmission
1" high, quarter rack width, metal enclosures (DVI 201 Tx
and DVI 201 Rx [non-Decora] only) — With low profile
enclosures, the transmitter and receiver can be discreetly
installed in locations such as behind a plasma or LCD
flat-panel display.
Wall-mountable enclosures (DVI 201 A D Tx and
DVI 201 A D Rx [Decora] only)
External 100 VAC to 240 VAC, 50/60 Hz, international power
supply (part #70-055-01) — Included with units sold as a
paired system and with transmitters.
1-4
DVI 201 Tx/Rx • Introduction
DVI 201 Tx/Rx • Introduction
1-5
Introduction, cont’d
DVI 201 Tx/Rx
2
Chapter Two
Installation and Operation
Mounting the Tx/Rx
Connections
Operation
Technical Points for Digital Video and Content Protection Encryption
Troubleshooting
Application Examples
1-6
DVI 201 Tx/Rx • Introduction
Installation and Operation
Mounting the Tx/Rx
C
Installation and service must be performed by
authorized personnel only.
VersaTools Rack Shelf
Non-Decora unit mounting
The 1" high, quarter rack width DVI 201 (non-Decora)
transmitters and receivers can be placed on a tabletop, mounted
on a rack shelf, or mounted under a desk or tabletop. The
receiver can be mounted on a projector bracket.
Tabletop placement
Affix the four included rubber feet to the bottom of the unit and
place it in any convenient location.
1/4 Rack Width Front
False Faceplate
Rack mounting
UL requirements
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the transmitter or receiver into or
onto a rack (figure 2-1).
1.
2.
3.
4.
5.
2-2
Elevated operating ambient — If the equipment is
installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment
may be greater than room ambient. Therefore, consider
installing the equipment in an environment compatible
with the +122 °F (+50 °C) maximum ambient temperature
(Tma) specified by Extron.
Reduced air flow — Installation of the equipment in a rack
should be such that the amount of air flow required for
safe operation of the equipment is not compromised.
Mechanical loading — Mounting of the equipment in
the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
Circuit overloading — Consideration should be given to
the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be
used when addressing this concern.
Reliable earthing (grounding) — Reliable earthing
of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections
other than direct connections to the branch circuit (such as
the use of power strips).
DVI 201 Tx/Rx • Installation and Operation
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Figure 2-1 — Mounting the transmitter or receiver
unit on a VersaTools rack shelf
Rack mounting instructions
For optional rack mounting, mount the transmitter or receiver
on any of the following rack shelves:
•
RSF 123 3.5" deep 1U VersaTools® rack shelf kit
(part #60-190-20) (figure 2-1)
•
RSB 123 3.5" deep 1U VersaTools rack shelf (part #60-604-20)
•
RSU 126 6" deep 1U universal rack shelf kit
(part #60-190-10)
•
RSB 126 6" deep 1U basic rack shelf (part #60-604-10)
•
RSU 129 9.5" deep 1U universal rack shelf kit
(part #60-190-01) (figure 2-2 on the next page)
•
RSB 129 9.5" deep 1U basic rack shelf (part #60-604-01)
On the non-VersaTools rack shelves, the transmitter or receiver
unit can be mounted in the front or the rear of the rack.
1.
Remove the feet from the bottom of the transmitter or
receiver unit, if they are installed.
2.
Mount the transmitter or receiver unit using two
4-40 x 3/16" screws in opposite (diagonal) corners to
secure the transmitter or receiver to the shelf.
3.
Install false faceplate(s) or other unit(s) to the rack shelf.
DVI 201 Tx/Rx • Installationand Operation
2-3
Installation and Operation, cont’d
1U Universal Rack Shelf
1/2 Rack Width
Front False
Faceplate
1/4 Rack Width
Front False
Faceplate
Both front false faceplates
use 2 screws.
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Figure 2-2 — Mounting the transmitter or receiver
unit on a standard rack shelf
Under-furniture mounting
The unit can be mounted under a horizontal surface using an
optional MBU 125 under-desk mounting kit (part #70-077-01).
Mount the unit under a desk or table as follows:
2-4
1.
Secure the under-desk mounting brackets to the
transmitter or receiver with the four machine screws
provided in the mounting kit (figure 2-3).
2.
Hold the transmitter or receiver with attached brackets
against the underside of the desk or other furniture. Mark
the location of holes for screws on the desk.
3.
Drill 1/4" (6.4 mm) deep, 3/32" (2 mm) diameter pilot
holes in the table or desk at the marked screw locations
from the underside or inside (the concealed side) of the
furniture, where the transmitter or receiver will be located.
4.
Insert the four wood screws into the pilot holes. Fasten
each screw into the installation surface until just less than
1/4" of the screw head protrudes.
5.
Align the installed screws with the slots in the mounting
brackets, and place the transmitter or receiver against the
surface, with the screws through the bracket slots.
6.
Slide the transmitter or receiver slightly forward or back,
then tighten all four screws to fasten it in place.
DVI 201 Tx/Rx • Installation and Operation
Figure 2-3 — Under-desk mounting
Through-furniture mounting
The transmitter or receiver can be mounted through a desk or
other furniture using an optional Extron MBD 129 through-desk
mounting kit, part #70-077-02. Mount the transmitter or receiver
through a desk or table as follows (figure 2-4):
Figure 2-4 — Through-desk mounting
DVI 201 Tx/Rx • Installation and Operation
2-5
Installation and Operation, cont’d
1.
2.
Loosely attach the mounting brackets to the transmitter
or receiver using the four machine screws and washers
supplied with the mounting kit.
Hold the transmitter or receiver against the inside of the
surface through which it will be mounted. Mark the four
screw holes on the inside of the surface to which you are
mounting the device.
3.
Drill four pilot holes, each 3/32" in diameter by 1/4" deep,
where you made marks.
4.
Using the provided four wood screws, secure the brackets
to the mounting surface.
5.
Slide the transmitter or receiver up and down in the
mounting brackets until the face of the transmitter or
receiver is at the desired height. Tighten the screws that
secure the brackets in place.
If the screws are inaccessible to a screwdriver:
Side Mounting
Plate
Bracket
Brace
U-Bolt
Extron
DVI 201 or HDMI 201
Receiver
Power Supply
Extron
PMK 300
Multi-product Pole Mount Kit
Front Mounting
Plate
a. Mark the location of the brackets relative to the screws.
b. Remove the transmitter or receiver from inside the
furniture.
c. Tighten the screws.
d. Replace the unit inside the surface (step 4).
Projector mounting
The receiver can be mounted on a projector bracket using either
of the following optional Extron projector mounting kits:
•
PMK 300 multi-product pole mount kit (part #70-374-01)
•
PMK 350 low profile, multi-product pole mount kit
(part #70-563-02 [black] or part #70-563-03 [white])
Figure 2-5 — PMK 300 projector mounting a receiver
3.
If the power supply is connected to the receiver, use the
two included tie wraps to strap the power supply to one of
the brackets.
PMK 300 mounting
Mount the receiver to a PMK 300 bracket as follows:
1.
If necessary, remove the feet from the bottom of the
receiver.
2.
Mount the receiver to one of the bracket’s three mounting
plates using two of the supplied 4-40 x 3/16" screws in
opposite (diagonal) corners to secure the device to the
bracket. It can be vertically mounted facing either up or
down (figure 2-5).
N
2-6
On the side mounting plates, the device is typically
mounted on the outside of the bracket.
On the front mounting plate, the device is typically
mounted on the inside of the bracket.
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-7
Installation and Operation, cont’d
N
The PMK 300 has a hole in the bottom plate that
allows the projector pole to be inserted through the
center of the plate (figure 2-6), rather than outside of
the plate (figure 2-5). To install the PMK 300 in this
configuration, slide the bracket up from the bottom of the
pole before the projector is installed on the pole.
PMK 350 mounting
Mount the receiver to a PMK 350 bracket as follows:
1.
Remove the front and rear plates from the PMK 350
(figure 2-7), using an Extron Tweeker or a #2 Philips
screwdriver. Retain the screws to reattach the plates when
you are finished.
Bracket
Brace
Extron
Quarter-rack
Sized Product
Rear Plate
Contoured
Base
U-Bolt
Extron
PMK 300
Multi-product Pole
Mount Kit
L-shaped
Bracket
Extron
PMK 350
U-bolt
Multi-product Pole
Mount Kit
Extron
Power Supply
Front Plate
Cover Sheet
Figure 2-7 — PMK 350 projector mounting a receiver
2.
If necessary, remove the feet from the bottom of the
receiver.
3.
Secure the receiver to one side of the mounting tray,
using two of the supplied 4-40 x 3/16" screws in opposite
(diagonal) corners.
4.
If power supply is connected to the receiver, use the
two included tie wraps to strap the power supply to the
bracket.
5.
Place the PMK 350 around the projector ceiling mounting
pole (figure 2-7).
Figure 2-6 — Projector pole on the inside
4.
5.
Place the contoured bracket brace against the pole and
opposite the back plate. The pole should fit snugly into the
depression in the center of the bracket brace.
Place the U-bolt around the ceiling pole. Insert the
two legs of the U-bolt through the round holes on the
contoured bracket brace and then through the slotted holes
on the bracket’s mounting plate.
N
6.
2-8
The supplied U-bolt fits a typical (1.5" to 2.0" diameter)
ceiling pole.
Secure the bracket to the U-bolt with the included hex
nuts, washers, and lock washers. Tighten the hex nuts just
enough that they can be loosened by hand.
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-9
Installation and Operation, cont’d
Assemble the U-bolt and the following parts in the
following order (figure 2-8):
6.
a. Pass the legs of the U-bolt through the slotted holes on
the mount plate flange.
b. Place the legs around the projector pole.
c. Pass the legs through the holes in the contour base.
N
The pole fits snugly into the depression in the
center of the contoured base.
d. Pass the legs through the holes in the L-shaped bracket.
N
The supplied U-bolt fits a typical (1.5" to 2.0"
diameter) ceiling pole.
Mount Plate
Flange
Contoured
Base
U-bolt
L-shaped
Bracket
Slotted Hole
in PMK Tray
L-shaped
Bracket Screws
Ceiling
Pole
Figure 2-8 — Hanging the tray on the pole
7.
Align the two slotted holes in the bottom of the L-shaped
bracket with the two slotted holes in the base of the tray.
Secure the L-bracket to the base by inserting two provided
6-32 x 5/16" screws through the aligned slots.
8.
Move the PMK 350 up to the desired location on the ceiling
pole, as close to the ceiling as desired.
9.
Secure the L-shaped bracket to the U-bolt using the
included hex nuts, washers, and lock washers. Tighten the
hex nuts securely.
N
Decora unit mounting
The DVI 201 A D (Decora) transmitter and receiver can be
installed in a one-gang electrical wall box with a Decora wall
plate cover (supplied).
The installation must conform to national and local electrical
codes and to the wall plate’s size requirements.
UL/Safety Requirements
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the Decora transmitters and
receivers into a wall or furniture.
1.
These units are not to be connected to a centralized DC
power source or used beyond their rated voltage range.
2.
These units must be installed in UL listed junction boxes.
3.
These units must be installed with conduit in accordance
with National Electrical Code.
Preparing the site and installing the wall box
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables. The
box should be at least 2.5" (6.4 cm) deep to accommodate the
connectors and cables. Install the cables into the wall, furniture,
or conduits before installing the wall plate.
N
The Decora units are very deep and have connectors
on the back side (figure 2-9 on page 2-12). Extron
recommends its 1-gang or 2-gang junction boxes
(part #s 980130 or 980084), which have a depth of
2.5" (6.4 cm).
Be sure to tighten the hex nuts securely enough that the
PMK 350 does not slide down the ceiling pole. A socket
wrench is recommended to tighten the hex nuts.
10. Secure the front and rear plates to the mounting tray with
four of the included #6 screws.
11. If desired, choose one of the provided four sizes of selfadhesive cover sheets, and apply it to the underside of the
mounting tray.
2-10
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-11
Installation and Operation, cont’d
2.50” [63.5mm]
Wall Stud
Signal
Output
Cable
Cable
Clamp
Wall Stud
Signal
Output
Cable
Cable
Clamp
TP Cable
(no boot)
TP Cable
(no boot)
1.51” [38.48mm]
Screws
or Nails
Captive
Screw
Connectors
Screws
or Nails
Figure 2-10 — Installing the wall box
N
If attaching the wall box to wood, use four #8 or #10
screws or 10-penny nails. A minimum of 0.5" (1.3 cm)
of screw thread must penetrate the wood.
If attaching the wall box to metal studs or furniture,
use four #8 or #10 self-tapping sheet metal screws or
machine bolts with matching nuts.
Junction Box
1.85” [47mm]
Figure 2-9 — Decora unit depth profile
6.
To install a new wall box, perform steps 1 through 9 below. If a
suitable wall box is already installed, perform steps 6 through 9
below. UL listed wall boxes are recommended.
1.
2.
Place the wall box (or your template) against the
installation surface, and mark the opening guidelines.
3.
Cut out the material from the marked area.
4.
Insert the wall box into the opening. The box or the wall
plate’s rear connectors should fit easily into the opening.
Enlarge or smooth the edges of the opening if needed.
5.
2-12
If a wall box is not available to use for a template, use the
dimensions on page A-9 to create a template. If installing
directly into furniture, cut out the center portion of your
template.
Secure the wall box with nails or screws, leaving the front
edge flush with the outer wall or furniture surface. See
figure 2-10.
DVI 201 Tx/Rx • Installation and Operation
Feed the twisted pair cables and, if applicable, the audio
and power cables through the opening and through the
wall box punch-out holes, securing them with cable clamps
to provide strain relief.
N
In order to fit in the junction box, the TP cables and
RJ-45 connectors should not have a boot installed.
N
One power supply can power both the transmitter and
the receiver, so only one unit needs a power supply.
7.
Trim back and/or insulate exposed cable shields with heat
shrink to reduce the chance of short circuits.
To prevent short circuits, the outer foil shield can be cut
back to the point where the cable exits the cable clamp.
8.
Connect the cables to the rear of the unit. See
"Connections", later in this manual, for connector wiring
details.
9.
Connect front panel devices (see "Connections", later in
this manual, for connector details), restore the power
supply, and test the transmitter/receiver system. Make
any cabling adjustments before final installation, as the
cables will be inaccessible afterwards.
DVI 201 Tx/Rx • Installation and Operation
2-13
Installation and Operation, cont’d
Final installation
After testing and making any adjustments, do the following:
1.
At the power outlet, unplug the power supply.
N
2.
One power supply can power both the transmitter and
the receiver, so only one unit needs a power supply.
Mount the transmitter or receiver into the wall box, and
attach the supplied Decora faceplate to the unit, as shown
in figure 2-11.
Connections
Transmitter connections
The rack-mountable transmitter is in a quarter rack width
enclosure. The wall-mountable transmitter is in an enclosure
that can be mounted in UL standard wall boxes with Decorastyle face plates.
Figure 2-12 shows the front panel of both DVI 201 Tx models.
Figure 2-13 shows the rear panel of both models.
DVI 201 Tx Front Panel
DVI INPUT
LOCAL OUTPUT
DVI 200 Tx Series
1
Wall Box
Decora
Faceplate
INPU
2
DVI 201 A D Tx Front Panel
T
I
DV
Wall opening
is flush with
edge of box.
DIO
IN
AU
-232
RS THRU
SS
PA
Tx
Rx
Extron
DVI 201 A D
INPUT
Figure 2-11 — Mounting the transmitter or receiver
DVI
3.
At the power outlet, reconnect the power supply. This
powers up both units.
AUDIO L+R
3
1
RS-232
PASS THRU
4
Rx
Tx
Figure 2-12 — DVI 201 Tx front panel connectors
2-14
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-15
Installation and Operation, cont’d
N
DVI 201 Tx Rear Panel
POWER
12V
0.4A MAX
DVI 201 Tx
DDC ROUTE
REMOTE
RS-232
PASS THRU
SPARE
1
LOCAL
2
5
Tx Rx
6
c
4
DVI 201 A D Tx Rear Panel
Audio input (DVI 201 A D Tx [Decora] only) — Connect an
unbalanced stereo audio source to this 3.5 mm mini stereo jack
for unbalanced audio input. Figure 2-14 shows how to wire the
audio plug.
Tip (L+)
1
Ring (R+)
Tip (L+)
6
Sleeve (Gnd)
2
Figure 2-14 — Audio input connector wiring
d
AUDIO
OUTPUT
L
DO NOT
CONNECT
TO LAN
POWER
12V
0.4A MAX
7
a
DVI input connector — Connect a DVI cable between this port
and the DVI output port of the digital video source. See "DVI
connector pin assignments," on page 2-22, for pin assignments.
b
Local output (DVI 201 Tx ([non-Decora] only) — If desired,
connect a DVI monitor for local monitoring of the input digital
image. See "DVI connector pin assignments," on page 2-22, for
pin assignments.
The RS-232 connector can also transmit one-way
modulated infrared (IR) signals. See "Modulated IR
pass through" on page 2-33.
e
DC power input connector — Plug the included external
12 VDC power supply into either this connector or the power
input connector on the receiver (item k on page 2-21). See
"Power supply wiring," on page 2-25, to wire the connector.
f
Transmitter output connector — Connect one end of two
separate TP cables to these RJ-45 female connectors.
C
DVI 201 Tx/Rx • Installation and Operation
RS-232 connector — Connect a serial communications port to
this 3.5 mm, 3-pole captive screw connector for bidirectional
RS-232 communication. See "RS-232 connector wiring," on
page 2-26, to wire the connector.
N
5
Figure 2-13 — DVI 201 Tx rear panel connectors
2-16
Sleeve (Gnd)
DVI 201
A D Tx
R
O
U
T
P
U
T
S
In a system where the local output is not used, ensure
that you power up the end display first before the video
source. Route the DDC to the remote end (see the
DDC Route DIP switch [item b, in "Operation", on
page 2-29]).
Do not connect these devices to a computer data or
telecommunications network.
N
In order to fit in the junction box, the TP cables and
RJ-45 connectors should not have a boot installed.
N
Extron recommends 28AWG to 24AWG TP cable for the
RJ-45 connectors.
Connect the free ends of the same TP cables from the transmitter
to the receiver’s Input RJ-45 female connectors (item h on
page 2-20).
DVI 201 Tx/Rx • Installation and Operation
2-17
Installation and Operation, cont’d
N
Connect transmitter output 1 to receiver input 1.
Connect transmitter output 2 to receiver input 2.
N
If necessary, test for proper cable connection (output 1 to
input 1, output 2 to input 2) as follows:
1. Plug both TP cables into the powered unit.
2. Momentarily connect either of the cables on the
opposite end into the unpowered unit‘s “2” connector.
If the unpowered unit’s Power LED is lit, the
connection is correct.
If the unpowered unit’s Power LED is not lit,
unplug the connector on the unpowered end and
connect the other cable to the “2” connector.
See "TP cable termination," on page 2-23, to properly wire the
RJ-45 connectors.
g
Audio Output connector (DVI 201 A D Tx [Decora] only) —
Connect one end of a 5-wire audio cable to this 3.5 mm, 5-pole
direct insertion connector.
Connect the free end of the same cable from the transmitter to
any compatibly wired unit, such as a switcher, an amplifier, or a
DVI 201 A D Rx (Decora) receiver.
Receiver connections
The rack-mountable receiver is in a quarter rack width
enclosure. The wall-mountable receiver is in an enclosure that
can be mounted in UL standard wall boxes with Decora-style
face plates.
Figure 2-16 shows the rear panel of both DVI 201 Rx models.
Figure 2-17 shows the front panel of both models.
DVI 201 Rx Rear Panel
DVI 201 Rx
POWER
12V
0.4A MAX
1
11
DVI OUTPUT
2
8
9
DVI 201 A D Rx Rear Panel
DVI 201 A D Rx
1
INPUTS
Figure 2-15 shows how to wire the captive screw audio
connector. Insert the wires into the appropriate openings in the
direct insertion connector. Tighten the screws on the side to
fasten the wires.
Do not tin the wires!
Figure 2-15 — Captive screw connector wiring for
transmitter audio output
C
AUDIO
INPUT
10
L
Sleeve (s)
Ring
Tip
R
DO NOT
CONNECT
TO LAN
Ring
Tip
POWER
AUDIO
OUTPUT
R
Balanced Output
NO GROUND HERE.
Tip
Sleeve (s)
NO GROUND HERE.
Tip
L
L
AUDIO
OUTPUT
R
Unbalanced Output
8
12V
0.4A MAX
2
11
Connect the sleeve to ground (Gnd). Connecting
the sleeve to a negative (–) terminal will damage the
audio output circuits.
Figure 2-16 — DVI 201 Rx rear panel connectors
2-18
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-19
Installation and Operation, cont’d
DVI 201 Rx Front Panel
RS-232
PASS THRU
Tx Rx
N
If necessary, test for proper cable connection (output 1 to
input 1, output 2 to input 2) as follows:
1. Plug both TP cables into the powered unit.
DVI 200 Rx Series
12
2. Momentarily connect either of the cables on the
opposite end into the unpowered unit‘s “2” connector.
If the unpowered unit’s Power LED is lit, the
connection is correct.
If the unpowered unit’s Power LED is not lit,
unplug the connector on the unpowered end and
connect the other cable to the “2” connector.
DVI 201 A D Rx Front Panel
N
OUTPUT
DVI
AUDIO OUT
See "TP cable termination," on page 2-23, to properly wire the
RJ-45 connectors.
i
DVI Output connector — Connect a DVI monitor or projector
for display of the transmitted direct digital image. See "DVI
connector pin assignments," on page 2-22, for pin assignments.
j
Audio Input connector (DVI 201 A D Rx [Decora] only) —
Connect one end of a 5-wire audio cable to this 3.5 mm, 5-pole
direct insertion connector.
Connect the free end of the same cable to any compatibly
wired audio source unit, such as a switcher's output or a
DVI 201 A D Tx (Decora) transmitter.
Figure 2-18 shows how to wire the captive screw audio
connector. Insert the wires into the appropriate openings in the
direct insertion connector. Tighten the screws on the side to
fasten the wires.
13
9
RS-232
PASS THRU
Tx
12
Rx
2-20
In order to fit in the junction box, the TP cables and
RJ-45 connectors should not have a boot installed.
N
Connect transmitter output 1 to receiver input 1.
Connect transmitter output 2 to receiver input 2.
DVI 201 Tx/Rx • Installation and Operation
AUDIO
OUTPUT
Ring
Tip
Sleeve (s)
Ring
Tip
Do not tin the wires!
Figure 2-18 — Captive screw connector wiring for
receiver audio output
Do not connect these devices to a computer data or
telecommunications network.
N
Sleeve
Tip
Balanced Input
L
AUDIO
OUTPUT
R
C
Tip
L
Receiver input connector — Connect one end of the two
separate TP cables from the transmitter output connectors (item
f on page 2-17) to these RJ-45 female connectors.
Sleeve
R
Unbalanced Input
Figure 2-17 — DVI 201 Rx front panel connectors
h
Extron recommends 28AWG to 24AWG TP cable for the
RJ-45 connectors.
k
DC power input connector — Plug the included external
12 VDC power supply into either this connector or the power
input connector on the transmitter (item e on page 2-17). See
"Power supply wiring," on page 2-25, to wire the connector.
DVI 201 Tx/Rx • Installation and Operation
2-21
Installation and Operation, cont’d
l
RS-232 connector — Connect a serial communications port to
this 3.5 mm, 3-pole captive screw connector for bidirectional
RS-232 communication. See "RS-232 connector wiring," on
page 2-26, to wire the connector.
N
m
The RS-232 connector can also transmit one-way
modulated infrared (IR) signals. See "Modulated IR
pass through" on page 2-33.
Audio output connector (DVI 201 A D Tx [Decora] only) —
Connect a stereo audio device to this 3.5 mm mini stereo jack to
receive the unbalanced audio output. Figure 2-14 on page 2-17
shows how to wire the audio plug.
TP cable termination
N
RJ-45 termination with CAT 5, CAT 5e, or
CAT 6 cable must comply with the TIA/EIA T 568A or
TIA/EIA T 568B wiring standard for all connections.
Figure 2-20 details the recommended termination of TP cables
with RJ-45 connectors in accordance with either the
TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.
Side
Pins:
TIA/EIA T
586 A
Pin Wire color
TIA/EIA T
586 B
Wire color
Signal
RJ-45 #1
RJ-45 #2
Pin assignments and wiring
White-orange
Data 0+
CEC
2
Green
Orange
Data 0–
HPD
DVI connector pin assignments
3
White-orange
White-green
ID Clock+
RS-232
TX
4
Blue
Blue
Data 1+
DDC Clk
5
White-blue
White-blue
Data 1–
+12 V
6
Orange
Green
ID Clock–
RS-232
RX
1 White-green
Figure 2-19 defines the pinout for the DVI protocol.
1
9
17
8
Insert
Twisted
Pair Wires
24
Male Connector
Female Connector
Pin
Signal
Pin
Signal
Pin
Signal
1
TMDS data 2–
9
TMDS data 1–
17
TMDS data 0–
2
TMDS data 2+
10
TMDS data 1+
18
TMDS data 0+
3
TMDS data 2
shield
11
TMDS data 1
shield
19
TMDS data 0
shield
4
Spare
12
Spare
20
Spare
5
Spare
13
Spare
21
6
DDC clock
14
+5 V power
7
DDC data
15
8
CEC control*
16
7
White-brown
White-brown
Data 2+
DDC data
8
Brown
Brown
Data 2–
Ground
N Terminate both ends of both cables identically, in accordance with
either the TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.
Figure 2-20 — TP cable termination
N
Do not use Extron’s UTP23SF-4 Enhanced Skew-Free™
A/V UTP cable to link the transmitter and receiver.
Skew-free A/V cable was designed for most Extron
TP transmitter/receiver applications, but the
DVI 201 Tx/Rx will not work properly with this cable.
Spare
N
22
TMDS clock
Shield
In order to fit in the junction box, the TP cables and
RJ-45 connectors should not have a boot installed.
N
If necessary, test for proper cable connection (output 1 to
input 1, output 2 to input 2) as follows:
Ground (+5 V)
23
TMDS clock+
Hot Plug Detect
24
TMDS clock–
* CEC control on pin 8 is a proprietary usage,
not the industry standard.
Figure 2-19 — DVI connectors
2-22
RJ-45
Connector
12345678
DVI 201 Tx/Rx • Installation and Operation
1. Plug both TP cables into the powered unit.
2. Momentarily connect either of the cables on the
opposite end into the unpowered unit‘s “2” connector.
If the unpowered unit’s Power LED is lit, the
connection is correct.
If the unpowered unit’s Power LED is not lit,
unplug the connector on the unpowered end and
connect the other cable to the “2” connector.
DVI 201 Tx/Rx • Installation and Operation
2-23
Installation and Operation, cont’d
Terminating shielded cable
N
The transmitter and receiver pair works with unshielded
twisted pair (UTP) or shielded twisted pair (STP) cables;
but, to ensure FCC Class A and CE compliance, STP
cables are recommended.
The Tx/Rx includes four shielded RJ-45 connectors and a length
of self-adhesive shielded tape that you can use to make the STP
cables that connect the transmitter and receiver.
N
Crimped Connector
Figure 2-23 — Crimped RJ-45 connector
Power supply wiring
N
Extron supplies the connectors and the shielded tape.
You must supply the CAT 5, 5e, or 6 STP cable.
Terminate the STP cable as follows:
1.
• Only one power supply is required. A single power
supply connected to either unit in the pair powers
both units.
• A single power supply is included with systems
packaged as a pair.
Peel back the cable shielding (figure 2-21) from the
end of the cable the length of the RJ-45 connector body
(approximately 7/8" [2.2 cm]) and fold it back.
• A power supply is also included with each
individually-packaged transmitter.
Figure 2-24 shows how to wire the connector.
Peel back shield and
fold back.
C
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply and
the transmitter or receiver. Identify the power cord
negative lead by the ridges on the side of the cord
(figure 2-24).
Figure 2-21 — Peeling back the cable shielding
2.
Cut away and discard the clear cellophane inner wrapper
from the end of the cable back to the folded-over cable
shielding.
3.
Peel the backing off the self-adhesive shielded aluminum
tape and wrap it around the folded-over cable shielding,
slightly overlapping the beginning of the tape
(figure 2-22).
Aluminum Tape
Wrap tape around folded foil shielding.
Slightly overlap.
Cut and save the excess tape
for other connectors.
Smooth
Ridges
A
A
4.
Cut the unused portion of the shielded tape and retain for
shielding other RJ-45 connectors.
5.
Crimp the RJ-45 cable in the normal manner, folding the
tangs at the end of the connector over the shielded tape
(figure 2-23).
DVI 201 Tx/Rx • Installation and Operation
SECTION A–A
Power Supply
Output Cord
NOTE Decora units have a
shorter connector,
without the tie wrap.
Tie Wrap
3
Ferrite Bead
Figure 2-22 — Wrapping the shielded tape
2-24
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
DC Power Cord
(between power supply
and DVI unit
power connector)
5
Captive Screw
Connector
Figure 2-24 — Power connector wiring
W
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before wiring.
DVI 201 Tx/Rx • Installation and Operation
2-25
Installation and Operation, cont’d
C
N
The length of the exposed (stripped) copper wires
is important. The ideal length is 3/16" (5 mm).
Longer bare wires can short together. Shorter wires
are not as secure in the connector and could be
pulled out.
Do not tin the power supply leads before installing in
the connector. Tinned wires are not as secure in the
connector and could be pulled out of the connector.
Operation
Figure 2-26 shows the DDC control and power indicator on the
non-Decora transmitter. Figure 2-27 shows the power indicator
on the Decora transmitter.
N
Both receiver models have power indicators in the same
location as on the related transmitter model.
DVI INPUT
Use the supplied tie-wrap to strap the power cord to the
extended tail of the connector.
N
Your transmitter/receiver pair may have shipped with a
blue captive screw connector. This blue connector can be
plugged into either a blue or an orange power receptacle.
The blue connector does not have the extended tail or the
included tie-wrap.
Snap the provided ferrite bead onto the DC power cable,
between the power supply and the DVI unit’s connector.
DVI 200 Tx SERIES
DVI 201 Tx Transmitter Front Panel
1
POWER
12V
0.4A MAX
N
Tx/Rx
Pins
The RS-232 connector can also transmit one-way
modulated infrared (IR) signals. See "Modulated IR
pass through" on page 2-33.
DVI 201 Tx
DDC ROUTE
REMOTE
RS-232
PASS THRU
SPARE
RS-232 connector wiring
Figure 2-25 shows how to wire the RS-232 connector for serial
communications.
LOCAL OUTPUT
2
LOCAL
1
2
Tx Rx
DVI 201 Tx Transmitter Rear Panel
Figure 2-26 — Non-Decora model control and
indicator
Connected RS-232
Device Pins
Ground
Transmit
Receive
Rx
Tx
Figure 2-25 — RS-232 connector wiring
C
N
2-26
The length of the exposed (stripped) copper wires
is important. The ideal length is 3/16" (5 mm).
Longer bare wires can short together. Shorter wires
are not as secure in the connector and could be
pulled out.
Do not tin the power supply leads before installing in
the connector. Tinned wires are not as secure in the
connectors and could be pulled out of the connector.
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-27
Installation and Operation, cont’d
Transmitter control and indicator
1
a
Power LED —
DVI 201 Tx (non-Decora) — This front panel LED lights green
to indicate that the unit is receiving power:
DVI 201 A D Tx (Decora) — This two-color front panel LED
lights to indicate signal and power status as follows:
Amber — The unit is receiving power but not a DVI input.
INPUT
DVI
AUDIO L+R
b
RS-232
PASS THRU
Rx
Tx
Green — The unit is receiving power and a signal is present on
the DVI input.
DDC Route switch (DVI 201 Tx ([non-Decora] only) —
This rear panel switch selects either the remote or local DVI
display as the route of the display resolution data (the display
data channel [DDC]) and HDCP copyright decoding keys.
Receiver indicator
N
a
DVI 201 A D Tx Transmitter Front Panel
Figure 2-27 — Decora model power indicator
Both receiver models have power indicators in the same
location as on the related transmitter model.
Power LED —
DVI 201 Rx (non-Decora) — This front panel LED lights green
to indicate that the unit is receiving power:
DVI 201 A D Rx (Decora) — This two-color front panel LED
lights to indicate signal and power status as follows:
Amber — The unit is receiving power but not a TP input.
Green — The unit is receiving power and a signal is present on
the TP input.
System operation
After the transmitter, the receiver, and their connected devices
are powered up, the system is fully operational. If any problems
are encountered, ensure all cables are routed and connected
properly.
N
2-28
DVI 201 Tx/Rx • Installation and Operation
Ensure that the video source and display selected for the
DDC are properly connected to the transmitter/receiver
pair, and that the transmitter, the receiver, and the
display have power applied before power is applied to
the video source. If all other devices are not turned on
before the video source, the image may not appear.
DVI 201 Tx/Rx • Installation and Operation
2-29
Installation and Operation, cont’d
Technical Points for Digital Video and Content
Protection Encryption
•
Digital Visual Interface (DVI) is a digital video format
that was created by the computer industry in 1999.
•
High Definition Multimedia Interface (HDMI™) is a
multimedia format that was created by the consumer
video industry in 2003.

•
•
2-30
The HDMI format is built onto the DVI format,
adding digital audio and control while reducing the
size of the connector.

The HDMI format is likely to replace the DVI format
in the near future.

With passive adapters, the HDMI format is backward
compatible with the DVI format.
With Extron adapters and/or cables, the DVI 201 fully
supports either format, regardless of the connector
type on the video source and display. See appendix A,
"Reference Information," for part numbers.
High-bandwidth Digital Content Protection (HDCP) is
an encryption method that protects copyrighted digital
entertainment material that uses DVI video.

HDCP is generated by video player hardware,
enabled by the video content.

The HDCP key is transmitted with the Display Data
Channel (DDC).

The DDC signal line was designed for the DDC’s low
data rate; the HDCP key rate is much higher.
♦
Without active buffering, an HDCP key signal
can travel only a short distance. The display
may properly receive the digital video signal, but
not the HDCP key. Without the key, the display
cannot decrypt the video signal. Symptoms of
undecrypted video may include a flashing black
or blue screen or “snow”.
♦
With active buffering, an HDCP key signal can
travel as far as other signals to ensure proper
decryption.
♦
The DVI 201 actively buffers the HDCP key.
DVI 201 Tx/Rx • Installation and Operation
Troubleshooting
DVI signals run at a very high frequency and are especially
susceptible to bad video connections, too many adapters,
or cables that are too long. To avoid the loss of an image or
introduction of image jitter, follow these guidelines:
•
The DVI cable on the input to the transmitter or
the output of the receiver should not exceed 10' (3 m).
•
Use only cable designed for DVI signals.
•
Limit or avoid the use of adapters.
•
If the display exhibits a flashing black or blue screen,
snow, or other distortion, a non-HDCP compliant display
may be receiving an HDCP-encrypted signal.
Check for an HDCP problem by ejecting the DVD from
the player. If the display distortion stops and the DVD
menu or screen saver image is clear, the problem is
HDCP-related.
•
Always power the display before the DVI video source in
order for the source to retrieve the DDC from the display.
•
The DVI 201 works as described in point-to-point
applications. Do not use any additional adapters, patch
panels, or couplers with the input DVI cables, output DVI
cables, and/or twisted pair cables. Additional links in the
signal chain can result in the reduction of signal integrity
and overall cable length performance.
DVI 201 Tx/Rx • Installation and Operation
2-31
Installation and Operation, cont’d
Application Examples
Modulated IR pass through
DVI 200 RX SERIES
TP 1
DVI 201 A D Tx
Modulated IR
Tx
Rx
RS-232
PASS THRU
DVI
AUDIO L+R
INPUT
Control
System
Ground
Tx
Rx
DVI 201 A D Tx Front
Figure 2-29 — Installation routing modulated IR
Source
DVI-D In
TP 2
DVI 201 Rx
RS-232
Audio System
DVI 201 A D Tx Rear
DO NOT
CONNECT
TO LAN
RS-232
PASS THRU
DVI
INPUT
AUDIO L+R
Audio
Tx Rx
PASS THRU
IR Emitter
Balanced Audio
Wiring
L+
L-
TP 2
Balanced Audio Out
DVI OUTPUT
1
2
Projector
1
2
R
O
U
T
P
U
T
S
L
DVI 201 RX
POWER
12V
0.4A MAX
AUDIO
OUTPUT
POWER
TP 1
DVI 201 Rx
12V
0.4A MAX
DVI 201
A D Tx
R+
R-
Figure 2-28 shows a standard installation with DVI video and an
audio input. The DVI 201 A D Tx converts the video input into
two proprietary TP outputs. The Tx outputs the audio directly
on a captive screw connector.
Figure 2-29 shows an installation in which the Tx/Rx pair sends
a modulated infrared (IR) signal across the link. On the TX side,
control system is connected to the Tx pin (the modulated IR
signal) and the Gnd (signal ground) on the transmitter. An IR
emitter is connected to the Tx and Gnd receiver output.
Flat Panel Display
w/ IR Control
Audio conversion
Figure 2-28 — Typical installation
2-32
DVI 201 Tx/Rx • Installation and Operation
DVI 201 Tx/Rx • Installation and Operation
2-33
Installation and Operation, cont’d
DVI 201 Tx/Rx
A
Appendix A
Reference Information
Specifications
Part Numbers
Decora Template Dimensions
2-34
DVI 201 Tx/Rx • Installation and Operation
Reference Information
Specifications
N
*Appropriate DVI-D to HDMI cables or adapters are required for
HDMI signal input/output.
Also, an optional Extron HDMI-to-DVI adapter is required in order to
transmit a CEC signal.
Number/signal type��������������������� 1 single link DVI-D (or HDMI*)
Connectors
DVI 201 Tx/Rx������������������ 2 female DVI-D
DVI 201 A D Tx/Rx����������� 2 female DVI-I
Audio— DVI 201 A D Tx/Rx
Video
Maximum data rate���������������������� 4.95 Gbps (1.65 Gbps per color)
Maximum pixel clock������������������� 165 MHz
Resolution range��������������������������� 1920x1200 or 1080p @ 60 Hz
Formats������������������������������������������� RGB and YCbCr digital video
Standards���������������������������������������� DVI 1.0, HDMI 1.2
Video input and loop through— transmitters
Number/signal type��������������������� 1 single link DVI-D (or HDMI*) input
1 single link DVI-D (or HDMI*) local loopthrough
Connectors
DVI 201 Tx/Rx������������������ 2 female DVI-D
DVI 201 A D Tx/Rx����������� 2 female DVI-I
Interconnection between transmitter and receiver
Connectors������������������������������������� (2) RJ-45 per unit for 2 CAT 5/5e/6/7
UTP (unshielded twisted parir) or STP
(shielded twisted pair) cables connecting
the transmitter and receiver
Termination standards����������������� TIA/EIA T568A or T568B. Pin
configurations for each standard are
available in the manual's installation
chapter.
Signal transmission distance
1900x1200 or 1080p @ 60 Hz
CAT 5/5e/6/7 STP��� Up to 125' (38 m)
CAT 5/5e/6/7 UTP�� Up to 100' (30 m)
1024x768 or 720p/1080i @ 60 Hz
CAT 5/5e/6/7 UTP or STP
Up to 200' (60 m)
N
A-2
Video output— receivers
The transmission distance varies greatly depending on the signal
resolution and on the type of cable, graphic card, and display used in the
system.
DVI 201 Tx/Rx • Reference Information
Gain������������������������������������������������� Unbalanced output: 0 dB;
balanced output: +6 dB
Frequency response���������������������� 20 Hz to 20 kHz, ±0.05 dB
THD + Noise���������������������������������� 0.10% @ 1 kHz at nominal level
S/N�������������������������������������������������� >85 dB at maximum output (unweighted)
Stereo channel separation������������ >86 dB @ 1 kHz
Audio input— DVI 201 A D Tx/Rx
Number/signal type
DVI 201 A D Tx������������������ 1 stereo, unbalanced
DVI 201 A D Rx������������������ 1 stereo, balanced/unbalanced
Connectors
DVI 201 A D Tx������������������ (1) 3.5 mm mini audio jack (tip, ring, sleeve)
DVI 201 A D Rx������������������ (1) 3.5 mm captive screw connector, 5 pole
Impedance
DVI 201 A D Tx������������������ >10k ohms unbalanced, DC coupled
DVI 201 A D Rx������������������ >18k ohms unbalanced, 14k ohms
balanced, DC coupled
Nominal level
DVI 201 A D Tx������������������ -10 dBV (316 mVrms)
DVI 201 A D Rx������������������ +4 dBu (1.23 Vrms)
Maximum level
DVI 201 A D Tx������������������ +11 dBu, unbalanced at 1% THD+N
DVI 201 A D Rx������������������ +16.8 dBu, unbalanced at 1% THD+N
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output— DVI 201 A D Tx/Rx
Number/signal type
DVI 201 A D Tx������������������ 1 stereo, balanced/unbalanced
DVI 201 A D Rx������������������ 1 stereo, unbalanced
Connectors
DVI 201 A D Tx������������������ (1) 3.5 mm captive screw connector, 5 pole
DVI 201 A D Rx������������������ (1) 3.5 mm mini audio jack (tip, ring, sleeve)
DVI 201 Tx/Rx • Reference Information
A-3
Reference Information, cont’d
Impedance
DVI 201 A D Tx������������������ 50 ohms unbalanced, 100 ohms balanced
DVI 201 A D Rx������������������ 50 ohms unbalanced
Maximum level (Hi-Z)
DVI 201 A D Tx������������������ >+16 dBu, balanced or unbalanced at
1% THD+N
DVI 201 A D Rx������������������ >+9.8 dBu, unbalanced at 1% THD+N
Maximum level (600 ohm)
DVI 201 A D Tx������������������ >+9 dBm, balanced or unbalanced at
1% THD+N
DVI 201 A D Rx������������������ >+6.8 dBm, unbalanced at 1% THD+N
Control/remote — external device (pass-through)
Serial control port input
Transmitter������������������������� RS-232 via (1) 3.5 mm, 3 pole captive screw
connector
Receiver������������������������������ 1 set of proprietary signals on a female
RJ-45 jack
Serial control port output
Transmitter������������������������� 1 set of proprietary signals on a female
RJ-45 jack
Receiver������������������������������ RS-232 via a 3.5 mm, 3 pole captive screw
connector
N
Protocol is mirrored between the transmitter and the receiver.
Serial control pin configurations� Captive screw connectors: 1 = TX, 2 = RX,
3 = GND
General
External power supply����������������� 100 VAC to 240 VAC, 50/60 Hz, 6 W max.,
external; to 12 VDC, 1 A, regulated
Power input requirements����������� 12 VDC, 0.4 A for both transmitter and
receiver
N
Each transmitter or receiver can be powered either locally by an external
power supply or remotely by receiver or transmitter on the other end of
the CAT 5/5e/6/7 cable.
Temperature/humidity���������������� Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling������������������������������������������� Convection, no vents
A-4
DVI 201 Tx/Rx • Reference Information
Mounting
Rack mount������������������������ Yes, with optional 1U, 9.5" deep rack
shelf (RSU 129, #60-190-01; RSB 129,
60-604-01); 1U, 6" deep rack shelf (RSU
126, #60-190-10; RSB 126 60-604-10); or
VersaTools® 1U, 3.5" deep rack shelf
(RSF 123, #60-190-20; RSB 123, 60-604-20)
Furniture mount���������������� Yes, with optional MBD 129 Through-Desk
Mounting Kit, #70-077-02
Pole mount������������������������� Yes, with optional PMK 250 mounting kit,
#70-526-02 or -03
Enclosure type������������������������������� Metal
Enclosure dimensions
DVI 201 Tx/Rx������������������ 1.0" H x 4.3" W x 3.0" D
(quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
DVI 201 A D Tx/Rx
Faceplate��������������������� 2.6" H* x 1.3" W x 0.1" D
(6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang Decora
faceplate.)
*Height is 3.8" [9.7 cm] including
mounting tabs.
Buffer��������������������������� 2.7" H x 1.8" W x 0.75" D
(6.9 cm H x 4.6 cm W x 1.9 cm D)
(Depth excludes connectors.)
Product weight������������������������������ 0.5 lbs (0.3 kg)
Shipping weight���������������������������� 3 lbs (2 kg)
Vibration����������������������������������������� ISTA 1A in carton
(International Safe Transit Association)
Listings������������������������������������������� UL, CUL
Compliances����������������������������������� CE, FCC Class A**, VCCI, AS/NZS, ICES
MTBF����������������������������������������������� 30,000 hours
Warranty����������������������������������������� 3 years parts and labor
N
**FCC testing is conducted with STP (shielded twisted pair) cable.
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
DVI 201 Tx/Rx • Reference Information
A-5
Reference Information, cont’d
Part Numbers
Mounting accessories
Accessories
Transmitter/receiver pair part numbers
N
The Tx/Rx system requires a transmitter/receiver pair. The transmitter and receiver can be purchased as a pair
(of the same form factor) or separately (to mix form
factors or Decora colors).
DVI 201 models
DVI 201 Tx/Rx (non-Decora)
Part number
60-734-03
DVI 201 Tx
60-734-12
DVI 201 Rx
60-734-13
DVI 201 A D Tx/Rx (Decora) black, white
Part number
RSF 123
3.5" deep 1U VersaTools® rack shelf kit
60-190-20
RSB 123
3.5" deep 1U VersaTools rack shelf
60-604-20
RSU 126
6" deep 1U universal rack shelf kit
60-190-10
RSB 126 6" deep 1U basic rack shelf
60-604-10
RSU 129
9.5" deep 1U universal rack shelf kit
60-190-01
60-865-02, -03
RSB 129 9.5" deep 1U basic rack shelf
60-604-01
DVI 201 A D Tx black, white
60-865-12, -13
MBU 125 under-desk mount kit
70-077-01
DVI 201 A D Rx black, white
60-865-22 -23
MBD 129 through-desk mount kit
70-077-02
PMK 300 pole mount kit
Included parts
These items are included in each order for a DVI 201 Tx/Rx:
Included parts
PMK 350 low profile pole mount kit (black,
white)
70-374-03
70-563-02, -03
Part number
One-gang junction box
980130
DVID SL/6 (with DVI 201)
DVI-D male-to-male, 6' (1.8 m) cable
(non-Decora units only)
26-585-02
Two-gang junction box
980084
12 VDC, 1 A external power supply
(1 per pair or 1 per separately-ordered unit)
70-775-01
IEC power cord (1 per power supply)
EWB one-gang external wall box,
black, white, RAL9010 white
60-452-02, 03,04
EWB two-gang external wall box
black, white, RAL9010 white
60-453-02, 03,04
3.5 mm, 2-pole captive screw connector
(non-Decora only) (1 per unit)
10-319-13
SMB one-gang surface-mount box, black,
white
60-639-02, 05
3.5 mm, 3-pole captive screw connectors
(1 per unit)
10-319-15
SMB two-gang surface-mount box, black,
white
60-640-02, 05
Tweeker (small screwdriver)
User’s manual
A-6
DVI 201 Tx/Rx • Reference Information
DVI 201 Tx/Rx • Reference Information
A-7
Reference Information, cont’d
Decora Template Dimensions
Cables
Accessories
Part number
DVID SL/6
DVI-D male-to-male, 6' (1.8 m) cable
26-585-02
HDMI M-M/6
HDMI male to male, 6' (1.8 m)
26-613-02
HDMI M-DVI-DM/6
HDMI male to DVI-D male, 6' (1.8 m)
26-614-02
If you need to create a template, use the dimensions shown on
figure A-1, below.
N
The drawing is not full size or to scale. Do not scale up
or print to use as a template.
2.79"
(7.09 cm)
Adapters
Accessories
Top
Panel
Part number
HDMIF-DVIDM
HDMI female to DVI-D male adapter
26-616-01
HDMIM-DVIDF
HDMI male to DVI-D female adapter
26-617-01
1.9"
(4.83 cm)
4.50"
(11.43 cm)
2.8"
(7.1 cm)
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
To install a
1-gang
DVI 201 A D Tx or
DVI 201 A D Rx
directly into
furniture or
wall, cut along
this line.
Figure A-1 — Decora Template Dimensions
A-8
DVI 201 Tx/Rx • Reference Information
DVI 201 Tx/Rx • Reference Information
A-9
Reference Information, cont’d
A-10
DVI 201 Tx/Rx • Reference Information
Download PDF

advertising